Download Sealeyy VS8196 Operating instructions

FEATURE PACKED
BORESCOPES
•
•
•
•
Big screens.
Rewind and playback.
Integral memory.
Ø5.5mm - Ø8.5mm
probes.
NEW
5.5mm
From £99.95+VAT
See page 3
25pc COOLING SYSTEM
PRESSURE TEST KITS
NEW
• Features 5 new adaptors
for increased vehicle
applications.
• Fast and effective way
of finding coolant leaks.
£199.95+VAT
See page 16
NEW
EOBD DIAGNOSTIC
TOOLS
• 3 New Models.
• Colour
screens.
• I/M Readiness
indicator.
From £49.95+VAT
See page 2
Promotion Code: VST12.09
Prices exclude VAT unless stated otherwise
Promotion Valid from 1st September to 31st December 2012
1
Patented One-Click I/M Readiness
Check
EOBD Code Readers
Save time and money, plus take the guess work out of fault finding and
diagnosis with CAN enabled EOBD diagnostic tools. Interrogate your
vehicle’s engine and emission faults with our updated range of tools
which reads and clears both pending and confirmed Diagnostic Trouble
Codes (DTC’s). The VS8800 is a new entry level tool which will display only
the DTC number – the description can be looked up on the CD supplied.
The VS8801 and VS8802 feature full colour screens and patented
one-click I/M readiness function. Both the larger units will read live data
direct from the vehicles ECU and the VS8802 will allow you to graph the
data enabling fast interpretation of engine per formance. In the event
that the software requires updating or the EOBD protocols are updated,
the VS8801 and VS8802 may be updated using a USB inter face. The
results from the VS8802 may be saved out to PC for sharing.
A faulty component monitored by EOBD does not
always turn on the MIL light on the dash board
straight away. The vehicle has to run through a
drive cycle to pend, then confirm DT Cs, before then
turning on the MIL light. Sealey
’s VS8801 and
VS8802 have a new feature which, using only
one click of a button , can tell the technician
which groups of sensors are ready for diagnosis and
have gone through the drive cycle. F
or Pre
MOT work this is vital and enables the technician to
confirm that the MIL light will not come back on during
the MOT, creating a fail.
The VS8802 is also loaded with a Tech-Tips data base allowing you a more
rounded description of the DTC fault and some ideas about where to look
next to correct the fault – lik e having a professional technician on call
24/7.
See the table below for a full list of features and vehicle coverage.
EOBD Code Reader
with Live Data
EOBD Code Reader
NEW
EOBD Code Reader Memory & Graphics
NEW
Colour
NEW
Colour
Tech Tips
OFFER PRICE
£49.95 exc VAT
£59.94 inc VAT
• Model No.
VS8800
• List Price
£64.95
OFFER PRICE
£69.95 exc VAT
£83.94 inc VAT
• Model No.VS8801
• List Price £95.95
VS8800
VS8801
VS8802
Works with all 1996 and later OBDII / EOBD compliant
vehicles
EOBD Code Reader Features
Scans for Diagnostic Trouble Codes (DTC) - The cause
of the 'Engine Malfunction Indicator Light' (MIL)
Scans for pending DTCs
Retrieves generic (P0, P2, P3 & U10) and manufacturer
specific (P1, P3 & U1) DTCs
Turns off MIL light, clears DTCs and resets monitors
Displays DTC definitions on screen
View freeze frame data
Displays monitor and I/M readiness status (emissions)
Patented One-Click I/M Readiness button (emissions)
Retrieves vehicle information (VIN, CID & CVN)
Supports CAN and other current EOBD Protocols
• Model No.VS8802
• List Price £199.95
£149.95 exc VAT
£179.94 inc VAT
Diagnostic guidance and tips in the palm of your hand.
Supports the new extended sensor list (SAE J1979 - 2007)
Reads live ECU/PCM data stream
Displays live O2 sensor data
Graphing function for live data (96on)
Read, store and playback live sensor data
Performs 'modules present' test
Print out data via PC
Update software via the internet
Built-in EOBD library lookup
Diagnostic trouble tips and repair information guide
2
OFFER PRICE
Large, easy-to-read LCD display
Backlit screen
Easy-to-use
Prices exclude VAT unless stated otherwise
Watch live data on the VS8801 and the VS8802. VS8802 will additionally
allow selected data to be graphed.
Promotion Code: VST12.09
Proscope
• 128Mb Integral memory allows the storage of up to 80 images or 90sec of video
on the handset – use a Micro SD card (not included) in the expansion slot to
increase your storage capacity if required.
• Record and replay still and video images on the handset or stream live video via
Second
Generation
Borescopes
the USB/AV connection.
• Features digital zoom control and rotate/flip control of the image – ideal for
use in a tight spot or with a mirror.
• Pistol-grip style is perfect for trade use.
128mb
Brightness
Zoom
Colour
Video
Playback
Video
Camera
Internal
Memory
USB
Connection
AV Out
Digital
Probe
SD
Digital
Camera
Storage
Not Included
Proscope2
VS8220
Proscope1
OFFER PRICE
£139.95 exc VAT
£167.94 inc VAT
• Ideal for the professional tradesman and technician.
• High performance pistol grip borescope with 60mm
colour TFT screen.
• Ø8.5mm Digital output camera module ensures low-loss
transmission of images to the hand-set and gives great
image quality with excellent colour balance and
contrast.
• Supplied with an AV-out cable and USB cable to allow
connection to a PC to capture, store and share images
and video.
• Kit includes a 45° mirror, hook and magnetic pick-up
attachment. Powered by 4 x AA batteries.
• Model No. VS8220
• List Price £189.95
OFFER PRICE
£199.95 exc VAT
£239.94 inc VAT
• High performance pistol grip bore scope with
89mm colour TFT screen.
• Ø5.5mm Digital output camera module ensures
low-loss transmission of images to the hand-set.
• Camera capsule is waterproof to 3mtr and has
scratch resistant, tempered glass lens.
• Powered by lithium-ion battery pack giving up
to 4 hours continuous use.
• Supplied with an AV-out cable and USB cable to
allow connection to a PC to capture, store and
share images and video.
• Kit includes a 45° mirror, magnetic pick-up
attachment and mains charger.
• Model No. VS8221
• List Price £299.95
VS8221
NEW
• Versatile video borescope with Ø8.5mm x 1000mm semi-rigid probe.
• Quickest and most cost effective solution, ideal for the inspection of
engines, machinery, buildings and infrastructure.
• Image displayed on a crystal clear, 60mm high resolution colour LCD
display with on-screen horizontal/vertical flip features for use with
side-view mirrors.
• CMOS camera with adjustable LED for fine control of light output and
clear pictures.
• Suitable for internal inspection of cylinder head
bores and vehicle compartments/components.
• Supplied with AV cable for external viewing of image.
• Uses 4 x AA batteries supplied.
• Model No. VS8196 • List Price £224.95
Brightness
Colour
Camera
AV Out
OFFER PRICE
£99.95 exc VAT
£119.94 inc VAT
Promotion Code: VST12.09
Prices exclude VAT unless stated otherwise
VS8196
Still the best quality
Scope for the money
3
Automotive Diagnostic Oscilloscope 4 Channel
One of the most competitively priced, PC -based scopes around and suitable
for professional applications. High sample rate, multiple memor y function
and 4-channel display mak e this unit ideal for in-depth analysis of a variety
of automotive sensors and components and can be used with any
compatible lap-top or PC. The scope also features a comprehensive collection
of standard automotive diagnostic procedures, turning an other wise complex
process into a click of a button. The system is loaded with specimen waveforms
allowing the operator to compare actual results with those expected. The
4-channel function allows multiple components to be compared simultaneously.
The TA4000 Can be connected using a LAN cable (supplied) to any PC running
the appropriate software version. The scope is supplied with a wide selection of
automotive type test leads, connectors and probes. Supplied in carr y-case.
Accessories (supplied): Power Supply Lead, Power Supply
Plug Adaptors x 4, Cigar Lighter Power Lead,USB Cable,
Attenuators x 4, Calibration Probe, Crocodile Clips; 4 x Red,
4 x Black, Standard Probes; 4 x Red, 4 x Black,Back Probes
x 5, HT Coil On Plug Extension Leads x 4, HT Couplers x 4,
Standard Leads x 4, Earth Cables x 4, Software Disc
(Driver & Instructions)
Maximum Sample Rate: 200MS/s (Single Channel), 100MS/s
(Dual Channels)
Bandwidth: 60MHz (-3dB)
Gain Range: 10mV - 5V/div @ x1Probe (10mV, 20mV, 50mV,
100mV, 200mV, 500mV, 1V, 2V, 5V/div 1,2,5 sequence)
100mV - 50V/div @ x10 Probe
1V - 500V/div @ x100 Probe10V - 5KV/div @ x1000 Probe
Coupling: AC, DC, GND
Impedance: 1MΩ
DC Accuracy:+/-3%
Input Protection: 35Vpk (DC + Peak AC < 10 kHz, without
external attenuation)
Display Mode: Y-T, X-Y
Predicted Waveforms: 81
Timebase Range: 5ns/div - 1000s/div (1-2-5 sequence)
Acquisition Mode: Realtime Sampling: 5ns/div - 200ms/div
Roll Mode: 500ms/div - 1000s/div
Buffer Size: 10K - 16M Points (Single Channel)
Type: Edge Trigger, Pulse Trigger
Mode: Auto, Normal, Single
Autoset: 4
Trigger Level: +/-4 Divisions
Measurements: Vpp, Vmax, Vmin, Vmean, Vrms, Vamp,
Vtop, Vbase, Vmid, Positive Overshoot, Negative
Overshoot, Cycle Mean, Cycle RMS, Period, Frequency,
Positive Pulse Width, Negative Pulse Width, Rise Time
(10%-90%), Fall Time (10%-90%), Positive Duty Cycle,
Negative Duty Cycle
Math: Addition, Subtraction, Multiplication, FFT
FFT: Rectangular, Hanning, Hamming, Blackman Window
Interface: USB2.0 (USB1.1 compatible)
Operating System: Window NT, 2000, XP, VISTA, Win7
Power: 8.5V DC
Size (L x W x D): 224 x 168 x 37mm
Visit www.sealey.co.uk
for FREE software
Download and
Demonstration Video.
Try the Software Mode
before you buy.
OFFER PRICE
£899.95exc VAT
£1079.94 inc VAT
FREE
EOBD Code
Reader with
Live Data
• Model No. TA4000
• List Price £1295.95
Hand-Held Automotive Single Channel
Oscilloscope & Multimeter
• Model No.
VS8801
• List Price
£95.95
Simple to use oscilloscope that allows obser
vation of
constantly varying signals from vehicle components and
sensors. With a bandwidth of 20MHz the unit is suitable for
detecting CAN signals on modern vehicles. Functions include
date hold, record, auto -ranging and USB inter face for
downloading data to PC. This versatile unit also has a built in
multimeter with large digit display and bar graph. Supplied
with 3-pin UK and 2-pin European charger leads.
Display: 320 x 240 pixel with LED Backlight
Bandwidth: 20MHz
Sample Rate: Maximum 80MSa/S
Input Impedance: 1MΩ
Maximum Input: 600V
Memory Capacity: 6 Waveforms
Trigger Mode: Auto, Normal,
OFFER PRICE
Single
Multimeter Modes: Voltage
exc VAT
DC & AC, Current DC & AC,
inc VAT
Resistance,Capacitance,
Continuity, Diode
Battery: 3.7V Lithium
Polymer
Operating Time: 3hr
with Backlight
Size: 211 x 140 x 55mm
EOBD Code
Weight: 700g
Reader with
PC Compatibility:
Live Data
Windows 98, ME,
2000, XP, Win7, Vista
• Model No.
VS8801
• Model No. TA330
• List Price
• List Price £799.95
£549.95
£659.94
FREE
£95.95
4
Prices exclude VAT unless stated otherwise
Promotion Code: VST12.09
Relay Circuit Diagnostic
Tester
0-30V Power Scope
Automotive Probe
• Features a scope function to visually
test component signals, with the added
benefit of maximum/minimum volts,
frequency and duty cycle displayed.
• Allows components to be activated
in situ or prior to installation.
• The fly lead allows continuity and
polarity testing with a high-contrast
colour LCD display giving a 7mm
high read-out.
• Feature audible and positive/negative
voltage indicator and two integral work
lights.
• 6mtr Lead connects to the battery
supply and reaches to all areas of
the vehicle. Includes a cigarette
lighter adaptor.
• Model No. PP100
• List Price £149.95
• Fast, accurate and safe relay circuit
tester that tests the supply, earth and
trigger wires within the automotive circuit.
• Simply remove the relay and install the
corresponding dummy relay.
• Includes a universal fly lead for non
standard relay pin configurations.
• Earth, supply and trigger terminals
are displayed as green or red LEDs.
• The tester can also be used to power
components by simulating the relay in
the on/off positions using the test button.
• Model No. TA130
• List Price £179.95
OFFER PRICE
£129.95 exc VAT
£155.94 inc VAT
FREE
Current Tester 20A Standard Fuse
•
OFFER PRICE
Model No.
TA120
List Price
£21.95
•
£119.95 exc VAT
£143.94 inc VAT
Vacuum Tester & Brake
Bleeding Kit
• Multi-function
diagnostic tool used to
test a variety of essential engine
and associated functions including
fuel, ignition, transmission and emissions.
• Brass-bodied vacuum pump features large,
easy-to-read vacuum gauge calibrated in
both inches and millimetres of mercury.
• Model No. VS4021
• List Price £69.95
Vacuum Tester and
Brake Bleeding Kit
NEW
OFFER PRICE
£34.95 exc VAT
£41.94 inc VAT
NEW
FREE
Mini Digital
Thermometer
Model No. VS906
List Price £17.95
Promotion Code: VST12.09
ARRIVING
OCTOBER
NEW
• Features laser pointer, Maximum/
Minimum/Average/Difference
readings, data storage and
data hold function, high/low
alarm setup, auto power off.
• Temperature is displayed on
a large 29mm LCD panel with
back-lit display for use in low
light areas and can be shown
in either °C or °F.
• Powered by 9V cell (supplied).
• Model No. VS907
• List Price £99.95
FREE
• Kit includes reservoir, hoses
and adaptors for bleeding
brake and clutch systems
on cars, commercials and
motorcycles.
• Model No: VS4022
• List Price £79.95
•
•
Infrared Laser Digital
Thermometer 12:1
OFFER PRICE
£44.95 exc VAT
£53.94 inc VAT
OFFER PRICE
£64.95 exc VAT
£77.94 inc VAT
8 Function Digital
Multimeter with
Thermocouple
•
•
Model No.
MM20
List Price
£29.95
Lambda Sensor Tester/Simulator
• Tests Zirconia and Titania lambda sensors and ECU.
• Suitable for 1, 2, 3 and 4 wire sensors, heated
and unheated.
• LED display shows crossover signal from sensor.
• Simulates rich or lean mixture signals to check
ECU response.
• Insulation-piercing clip for quick and easy
connection plus, display to confirm wire identity.
• Features a low battery indicator and powered
by 9V battery (supplied).
• Model No. VS925
• List Price £99.95
OFFER PRICE
£69.95 exc VAT
£83.94 inc VAT
Prices exclude VAT unless stated otherwise
5
8 Function Digital Automotive
Analyser
12 Function Digital Automotive
Analyser
• Durable bi-composite case and integral stand
suitable for the toughest workshop conditions.
• Large, hi-contrast LCD display with 21mm high
digital read-out.
• Unique Test Lead Connection feature.
• Includes data hold feature
OFFER PRICE
and low battery display.
• Supplied with test probes
exc VAT
and crocodile clips.
• Model No. TA200
inc VAT
• List Price £59.95
• Durable bi-composite case and integral stand
suitable for the toughest workshop conditions.
• Large, hi-contrast LCD display with 18mm high
digital read-out and bar graph.
• Auto-ranging, data-hold, auto-polarity, autopower-off and low battery display functions.
• Bar graph simplifies lambda
sensor testing.
• Supplied with capped
OFFER PRICE
test probes and K-type
exc VAT
thermocouple.
• Model No. TA101
inc VAT
• List Price £64.95
£39.95
£47.94
£44.95
£53.94
12V Battery Drop Tester
• Integrated circuit, high visibility, backlit, LCD display
and five position stand.
• Fourteen functions including pulse-width measurement
for fuel injectors, idle air control motors and electronic
transmission control systems.
• Auto-ranging and auto-power-off.
• Suitable for AC and DC circuits.
• Supplied with test leads, inductive coupler with
adjustable sensitivity, K type
OFFER PRICE
temperature probe and
operating instructions.
exc VAT
• Model No. TA202
• List Price £99.95
inc VAT
£69.95
£83.94
6/12V Battery
Drop Tester
• Traditionally styled drop tester
for all 12V automotive batteries.
• Applies load across cells and
measures output on meter.
• Accurate indication of battery
voltage, faulty cell and short
circuited cell.
• Model No. BT91/3
• List Price £162.95
•
•
•
•
•
American style drop tester.
Load applied by internal switchgear - no sparking!
Suitable for 6 and 12V batteries.
Applies load across cells and measures output on meter.
Accurate indication of battery voltage, faulty cell and
short circuited cell.
• Model No. BT91/7
• List Price £59.95
OFFER PRICE
£119.95 exc VAT
£143.94 inc VAT
12V LED Battery/Alternator
Tester with Crocodile Clips
OFFER PRICE
£10.95 exc VAT
£13.14 inc VAT
OFFER PRICE
£34.95 exc VAT
£41.94 inc VAT
Dial Type Battery Fluid Tester
6pc Noid Light Set
• Tests 6, 12 and 24V batteries.
• Composite body and rubber
bulb for workshop durability.
• Model No. AK410
• List Price £6.45
• LED Indicators verify condition
of battery and alternator.
• Magnetic backing sticks
to metal surfaces for
hands-free operation.
• Model No. AK400
• List Price £16.95
6
14 Function Digital Automotive
Analyser with Inductive Coupler
• Check fuel injector signal faults fast.
• Easy-to-use and fits a wide variety
of injector harnesses.
• Applications: GM PFI, Ford
OFFER PRICE
TBI, GEO TBI, Bosch PFI,
exc VAT
GM TBI, GM SCPI.
• Model No. VS213
inc VAT
• List Price £21.45
£13.45
£16.14
Prices exclude VAT unless stated otherwise
OFFER PRICE
£3.95
£4.74
exc VAT
inc VAT
Promotion Code: VST12.09
6 Function Professional Auto-Ranging
Digital Clamp Meter NCVD
Diagnostic Socket
Memory Safe
EOBD 12V
NEW
• Used to preserve the memory
to on-board electronics whilst
vehicle's own battery is
disconnected.
• Can be connected via the
vehicle's EOBD or cigarette
lighter socket.
• Unit features an internal 12V
4Amp sealed battery and LEDs
provide battery condition and
charge indicator.
• Supplied with mains charger.
• Model No.VS2071
• List Price £129.95
FREE
6-24V Circuit Tester
OFFER PRICE
£49.95 exc VAT
£59.94 inc VAT
FREE
Compression Tester
Push-On Type with
Straight Stem
OFFER PRICE
£86.95exc VAT
£104.34 inc VAT
• Conforms to EN 61010-1 CATIII 600V safety
requirements for electrical equipment for
measurement, control and laboratory use.
• Features non-contact AC voltage detection
function while controls are laid out to enable
use with one hand.
• Includes data and max hold functions.
• Double moulded housing with soft grip case
and large display for ease of use.
• Supplied in zipped pouch with carry strap.
• Model No. TM105
• List Price £69.95
•
•
Model No. CT954
List Price £20.45
ARRIVING
OCTOBER
Digital Automotive Analyser
12 Function with IC
• Reads standard automotive
parameters including duty
cycle.
• Features auto-ranging and
data hold functions with
overload protection on all
ranges.
• Model No. TA302
• List Price £99.95
•
•
Model No. AK4008
List Price £7.75
FREE
90pc Test Lead Kit
• Comprehensive set of test
leads and components
suitable for testing, isolating
and evaluating automotive
electronic circuits.
• Kit includes standard
Ø4mm banana style
plugs and sockets
suitable for use with most
diagnostic multimeters
and test equipment.
• Supplied in sectioned
carry-case for quick
location of components.
• Model No. TA111
• List Price £234.95
12 & 42V Hybrid Vehicle
Circuit Tester
•
•
Model No. AK4010
List Price £25.95
OFFER PRICE
£169.95 exc VAT
£203.94 inc VAT
9 Function Workshop
Volt/Amp Meter
6-24V
FREE
Diagnostic Socket
Memory Safe - EOBD
•
•
Model No. VS2072
List Price £29.95
OFFER PRICE
£69.95 exc VAT
£83.94 inc VAT
• Reads up to 32V/100Amps.
• Tests battery voltage, feed voltage,
earth contact, alternator current, equalization,
alternator drop, electric system and rundown current.
• Steel case with carry strap.
• 2 Large meter read-out display.
• Supplied with two pairs of leads with crocodile clips
and full operating instructions.
• Model No. BT91/5
• List Price £99.95
Digital Battery Tester
with Printer 6/12V
12V Digital Battery
& Alternator Tester
• Fast, accurate diagnosis and
recording of battery faults.
• LCD Screen shows easy-to-follow
test prompts and results.
• Integral printer will produce hard-copy
results for your own or customer’s records.
• Suitable for Regular Liquid, AGM Flat Plate,
AGM Spiral and Gel batteries.
• Supplied with carry-case, two printer rolls
and instruction manual.
• Model No. BT2013
• List Price £399.95
• Utilises
low
current
draw
technology
to evaluate
condition of SLI, VRLA,
AGM and Gel batteries.
• Suitable also for the evaluation
of the alternator and charging
circuitry of the vehicle - the results
displayed simply and clearly on
the LED panel.
• Model No. BT102
• List Price £89.95
Promotion Code: VST12.09
OFFER PRICE
£289.95 exc VAT
£347.94 inc VAT
Prices exclude VAT unless stated otherwise
OFFER PRICE
£64.95 exc VAT
£77.94 inc VAT
OFFER PRICE
£64.95 exc VAT
£77.94 inc VAT
7
13-Pin Towing Socket Tester
12V - VOSA Approved
20A Current Testers
20
l
de
Mo
A1
.T
No
21
l
de
A1
.T
No
Mo
• Ideal for fault-finding on car and commercial vehicle electrical circuits.
• Plugs straight into the vehicle's fuse board.
Model No.
Range
Fuse Type
List Price
Exc. VAT
Inc. VAT
TA120
0-20A - 0-48V
Standard
£21.95
£12.95
£15.54
TA121
0-20A - 0-48V
Mini
£21.95
£12.95
£15.54
• Quick and simple test of 12V
13-pin Euro-type sockets fitted
to the rear of the vehicle.
• Features self-test facility to ensure
the serviceability of the tool.
• Also tests the 12V continuous live feed,
12V ignition live feed and the reversing
lights - not part of the current MOT test,
but useful when diagnosing electrical
faults.
• Includes 13 to 7 pin adaptor for testing
older wiring systems.
• Model No. TST22
• List Price £99.95
OFFER PRICE
£49.95 exc VAT
£59.94 inc VAT
Coil On Plug Test Extension
Car Fuse
Adaptor
Lead Sets
• Ideal for use on
car and commercial
vehicles.
• Fitted with regular
Ø4mm banana
adaptors found
on most scopes
and multimeters.
• Maximum
Current/Voltage:
20A/48V.
FREE
Wire Piercing
Guide Clip
lN
de
Mo
Model No. Fuse Type
•
•
24
23
1
TA
o.
l
de
Mo
.
No
1
TA
List Price
Exc. VAT
Inc. VAT
TA123
Standard
£12.95
£7.95
£9.54
TA124
Mini
£12.95
£7.95
£9.54
FREE
Automotive Test Probe
• Allows for inductive couplers to be used on engines
that have no HT leads to diagnose engine faults.
• Ideal for coil-pack diagnostics on modern engines.
• Enables the technician to correctly diagnose a fault
without unnecessary component changing.
• Simply plugs in-between the coil-pack and spark plug.
• Model No. VS5263
• List Price £34.95
Model No. TA115
List Price £7.75
OFFER PRICE
£22.95 exc VAT
£27.54 inc VAT
399pc Crimping Tool Set
Automotive Test Probe
•
•
• Checks for short circuits and bad
earths quickly and easily.
• Tests continuity and polarity using
flying lead and also indicates
voltage (2V to 24V) of system on
test using an LED array.
• Power-up components prior to
installation and check in situ
function of components and
accessories allowing fast
problem diagnosis.
• Features integral work light
with touch sensitive control.
• Model No. PPVT
• List Price £59.95
Model No. VS906
List Price £17.95
OFFER PRICE
£35.95 exc VAT
£43.14 inc VAT
Automatic Wire
Stripping Tool
• One-handed, compound action pliers grip and strip
electric cables from 0.5mm2 up to 5.5mm2 automatically.
• Jaw action prevents crushing or cutting even the finest
wires.
• Supplied with length gauge and fitted with vinyl grips.
• Model No. AK2252
• List Price £18.95
8
• Comprehensive crimping tool
and accessory set, including
5-function crimping tool with soft
rubber grips for comfort and control.
• Model No. AK8904
• List Price £54.95
OFFER PRICE
£34.95 exc VAT
£41.94 inc VAT
Ratchet Crimping Tool Insulated Terminals
OFFER PRICE
£11.95
£14.34
exc VAT
inc VAT
• All steel construction with large comfort grip
handles and hardened and tempered jaws.
• Ratchet action ensures consistent crimping.
• Terminal Suitability: 0.5-1.0mm2, 1.5-2.5mm2,
4.0-6.0mm2.
• Model No. AK3864
• List Price £42.95
Prices exclude VAT unless stated otherwise
OFFER PRICE
£27.95 exc VAT
£33.54 inc VAT
Promotion Code: VST12.09
Fuel Injection Pressure Test Kit
90ltr Stainless Steel
Fuel Tank Drainer
• Comprehensive kit of hoses, adaptors
and fittings for testing the pressure on
modern petrol fuel injection systems.
• Fitted with quick couplings and safety
valve to prevent inadvertent discharge
of fuel under pressure.
• Supplied with Ø92mm single high
pressure gauge with rubber bumper,
reading 0-120psi and 0-8bar.
• Gauge features a hanging hook and
suction cup.
• Pressure release valve fitted with long
drain hose allows safe recovery of fuel.
• Model No. VSE212
• List Price £399.95
• Stainless steel fuel drainer
with venturi type suction.
• 90ltr Capacity tank suitable
for petrol or diesel.
• Supplied with suction tubes
and adaptors for breaking
into vehicle fuel system.
• CE Certified (971231EC).
• Model No. TP201
• List Price £1649.95
FREE
6pc Petrol Engine
Compression Tester
Deluxe Kit
OFFER PRICE
£289.95 exc VAT
£347.94 inc VAT
FREE
•
Model No. VSE300D
List Price
£124.95
Diesel Injection Leak Back Master
Kit - Bosch/Delphi/Denso
6kg Dry Powder Fire
Extinguisher
•
•
•
• Identifies worn, blocked
or inoperative injectors
quickly and easily.
• Contains measurement
tubes for short term tests
and measurement bottles
for long term, more accurate
evaluation.
• Master kit includes range of
adaptors to suit Bosch, Delphi &
Denso injectors for comprehensive
coverage of common rail diesel vehicles.
• Model No. VS2048 • List Price £179.95
Model No.
SDPE06
List Price
£93.95
OFFER PRICE
FREE
8 Function Digital
Multimeter with
Thermocouple
OFFER PRICE
£1145.95 exc VAT
£1375.14 inc VAT
£99.95 exc VAT
£119.94 inc VAT
• Essential for reintroduction of fuel into fuel pump
following maintenance such as fitting of new
diesel filter or following
drainage of fuel tank.
OFFER PRICE
• Must be used whenever
exc VAT
fuel system is disturbed.
• Model No. VS055
inc VAT
• List Price £19.95
• Popular glow plug sized 3/8"Sq drive Chrome Vanadium
steel sockets with universal joints for simple replacement.
• Features rubber inserts for
retention of plug in socket.
• Socket Sizes: 8, 10, 12mm.
OFFER PRICE
• Set includes 75mm
exc VAT
extension bar.
• Model No. SX0402
inc VAT
• List Price £31.95
Diesel & Petrol Fuel
Pump Priming Tool
Fuel Filter Cap
Removal Tool
£10.95
£13.14
•
Model No.
MM20
List Price
£29.95
Injector Nozzle
Tester - Diesel
4pc 3/8"Sq Drive
Diesel Glow
Plug Socket
Set
Diesel Injection System
Priming Device
•
£19.95
£23.94
• Enables the testing of
injectors under pressure.
• Fitted with Ø88mm gauge
with rubber bumper reading
both psi and Bar.
• Ideal for checking of atomisation
pattern and opening pressure.
• Transparent reservoir fitted with
fine filter and unit supplied with
two injector connection pipes.
• Model No. VS2058
• List Price £299.95
OFFER PRICE
£199.95 exc VAT
£239.94 inc VAT
Fuel Feed
Pipe Pliers
NEW
• Required for priming injection pump.
• Use after diesel filter change, drainage of fuel
tank or any other disturbance of the fuel system.
• Supplied with two fuel
OFFER PRICE
pipe clips.
• Suitable for 9mm bore
exc VAT
hose.
• Model No. VSE055
inc VAT
• List Price £15.95
£9.95
£11.94
Promotion Code: VST12.09
• Specialist socket
required for the
removal of diesel
fuel filter fitted to
2.0, 2.2 HDi engines
found in some
Citroen, Ford, Land
Rover, Mitsubishi and
Volvo vehicles.
• Model No. VS6426
• List Price £15.95
OFFER PRICE
£9.95
£11.94
exc VAT
inc VAT
Prices exclude VAT unless stated otherwise
• Suitable for releasing
connections on in-line
fuel line filters.
• Fitted with long handle
for restricted access.
• Model No. VS0458
• List Price £22.95
OFFER PRICE
£14.75
£17.70
exc VAT
inc VAT
9
14pc Diesel Injector
Puller Set
Cylinder Head
Component
Organiser
• Suitable for the fast
and safe removal of
Bosch, Delphi, Denso
and Siemens diesel injectors.
• Ball joint allows hammer to be
used in confined areas.
• Set includes keys and deep open
profile sockets, used to dismantle
injectors, plus adaptors for attaching
the slide hammer securely to the body of the injector.
• Contents: Slide Hammer, 4pcs 1/2" Sockets, 25, 27, 29
and 30mm, Tamper Proof Key, 5pcs Adaptor (Bosch,
Delphi, Denso, Siemens), Ball Joint.
• Model No. VS2059
• List Price £239.95
OFFER PRICE
£149.95 exc VAT
£179.94 inc VAT
Fuel Filter Removal Kit Vauxhall/Opel
NEW
• An essential item for a cylinder
head rebuild.
• Keeps all components neat
and tidy as they come off
the cylinder head.
• Saves time and frustration.
• Model No. VSR01
• List Price £39.95
OFFER PRICE
£26.95 exc VAT
£32.34 inc VAT
6pc Diesel Injector
Seat Cleaner Set
• Set of four diesel injector seat
cleaners, centring pilot and
T-handle.
• Used to clean/decarbonise
injector seats when changing
injectors.
• Helps to avoid blow-back due
to poorly seated injectors.
• Suitable for a wide range
of vehicles.
• Model No. VS2055
• List Price £119.95
• Designed to remove the fuel
filter on Vauxhall/Opel vehicles
fitted with 1.9CDTi engines.
• Also fits some Alfa Romeo, Fiat
and Saab 1.9JTD/TD vehicles.
• Filter housing fits into the plastic
holder using a vice, so the key
can be used to unscrew the
housing cap without causing
damage.
• Model No. VS2065
• List Price £79.95
FREE
6-24V Auto Probe with
4.5mtr Cable
£49.95 exc VAT
£59.94 inc VAT
£44.95 exc VAT
£53.94 inc VAT
8pc Glow Plug
Reamer/Base
Cleaning Set
•
•
OFFER PRICE
OFFER PRICE
33pc Glow Plug
Thread Repair Set
FREE
FREE
4pc 3/8"Sq Drive Diesel
Glow Plug Socket Set
Angular Torque Gauge
1/2"Sq Drive
•
•
• Quickly removes accumulations of carbon residue
inside the cylinder head assisting the installation
and effective operation of replacement glow plugs.
• Includes four ream guides which aid the centralisation
of the Chrome Vanadium reams.
• Suitable for M8, M10 and M12 threaded glow plugs.
• Model No. VS312
• List Price £169.95
10
•
•
Model No.
VS530
List Price
£16.95
OFFER PRICE
£99.95 exc VAT
£119.94 inc VAT
Model No. SX0402
List Price £31.95
• Fast and effective remedy for damage to cylinder
head glow plug threads.
• Set includes tools for the precise insertion of threaded
inserts into the head and features a unique tap guide
system to ensure their correct alignment.
• Includes 4 sizes of threaded adaptors suitable for
common sizes of glow plug.
• Model No. VS311
• List Price £173.95
OFFER PRICE
£119.95 exc VAT
£143.94 inc VAT
Glow Plug Puller Set
HGV Injector Nozzle
Socket - Diesel
• Suitable for the removal and installation of the
diesel injection nozzle on MAN, Mercedes-Benz
and Scania commercial vehicles.
• Specially designed with window, toothed
end and M14 pulling force screw.
• Model No. SX0411
• List Price £32.45
Model No. PP1
List Price £39.95
• A comprehensive set suitable for
removing stubborn glow plugs.
• Ideal for removing plugs that
have been unscrewed,
but seized, due to
residue build up
or where the
filament
has been
distorted.
• Quick
and effective
method, saving
time and money.
• Model No. VS313
• List Price £124.95
OFFER PRICE
£19.95 exc VAT
£23.94 inc VAT
OFFER PRICE
£84.95 exc VAT
£101.94 inc VAT
Prices exclude VAT unless stated otherwise
FREE
20pc Cleaning &
Decarbonising
Brush Set
•
•
Model No. VS1800
List Price £35.95
Promotion Code: VST12.09
FREE
Diesel & Petrol
Compression,
Leakage & TDC
Kit
14pc Valve Seat Cutter
Brake Pipe Cutter
•
•
Model No. VS0350
List Price £24.95
• Suitable for re-cutting inlet/exhaust
valve seats concentric to the valve
guides.
• Features tungsten carbide cutting
blades, expandable pilots and
double end cutters for increased
application.
• Cutter Sizes: Ø28-37mm 45º & 75º,
Ø28-37mm 30º & Ø37-44mm 75º,
Ø37-46mm 45º & 60º, Ø37-46mm
30º & Ø44-52mm 75º, Ø46mm
45º & Ø60mm 30º, Ø52mm
75º & Ø65mm 60º.
• Model No. VS1825
• List Price £889.95
FREE
2pc Valve Grinder
Set
OFFER PRICE
£649.95exc VAT
£779.94 inc VAT
• A comprehensive kit for testing
the compression and leakage
on both diesel and petrol vehicles.
• Features 600psi gauge with large rubber
bumper, straight and right angled quick
connect fittings and an extensive range
of spark/glow plug and injector adaptors.
• Includes TDC finder, ideal for use when the
engine has no crankshaft timing marks.
• Model No. VSE3156
• List Price £389.95
OFFER PRICE
£234.95exc VAT
£281.94 inc VAT
•
•
Technician's Straight
Edge
Model No. VS1653
List Price £9.95
•
•
Model No. VS1481
List Price £61.95
10pc Petrol Compression
Test Kit
FREE
with
each
Model No. Depth
Capacity
List Price
Model No. VS158
Model No. VS157
Model No. VS156
Model No. VS155
Piston Ring Compressors
Exc. VAT
Inc. VAT
2pc Valve Grinder Set
VS155
75mm Ø60-125mm
£12.95
£8.45
£10.14
•
•
VS156
75mm Ø60-175mm
£18.95
£12.45
£14.94
VS157
100mm Ø60-150mm
£19.95
£12.95
£15.54
VS158
150mm Ø60-150mm
£26.95
£17.95
£21.54
Model No. VS1653
List Price £9.95
Fuel Tank Sender Spanner
3-Leg Ø75-160mm Drive
24mm
• For removing and
refitting fuel tank
sender mounting
rings.
• Model No. VS6423
• List Price £26.95
• Ø59mm Gauge fitted with 250mm
hose and quick connect.
• Scale reads from 0-21bar(0-300psi).
• Includes four extension hoses and seven
plug thread adaptors from 10 to 18mm.
• Suitable for most petrol engined cars
and light commercials.
• Model No. VSE206
• List Price £99.95
£17.95
£21.54
exc VAT
£64.95 exc VAT
£77.94 inc VAT
Compression Testers
Push-On Type
• Fitted with Ø63mm gauge
reading up to 300psi and
20kg/cm2.
• Cone type spark plug
connection on straight
rigid 130mm extension
aids quick installation
on most petrol engines,
including motorcycle
and small portable
power units.
Model No.
OFFER PRICE
OFFER PRICE
Model No. CT953
Model No. CT954
Type
List Price
Exc. VAT
Inc. VAT
CT953
Angled
£20.45
£12.95
£15.54
CT954
Straight
£20.45
£12.95
£15.54
inc VAT
600mm Precision Straight Edge
Cylinder Head Stands
• Two support stands which
locate into cylinder head
via stud holes.
• Also provide clearance
between head and
workbench for reaming
valve guides.
• Model No. VS1555
• List Price £28.45
• Suitable for testing for distortion
on cylinder heads and engine
blocks during engine overhauls
and rebuilds.
• May be used with feeler gauges
for high precision work.
• Supplied in storage case.
• Model No. VS1480
• List Price £135.95
FREE
15 Blade Feeler
Gauge - Metric
OFFER PRICE
£15.95 exc VAT
£19.14 inc VAT
Promotion Code: VST12.09
OFFER PRICE
£89.95 exc VAT
£107.94 inc VAT
Prices exclude VAT unless stated otherwise
•
•
Model No.
VS511
List Price
£8.95
Angular Torque Gauge
1/2"Sq Drive
•
•
Model No.
VS530
List Price
£16.95
11
FSI Injector Remover/Installer
& Service Kit - VAG
NEW
• Injector remover/installer and
service kit for petrol injectors
found in VAG vehicles covering
1.4, 1.6, 1.8, 2.0, 2.7 V6, 3.0 V6,
3.2 V6, 3.6 V6 and 4.2L V8
FSI engines.
• Model No. VS2069
• List Price £154.95
• New lightweight design for the
installation of bearings without
damaging the bearing or
housing.
• Contains 3 metal bearing drift
sleeves and 34 nylon drifts.
• Can also be used to install oil
seals.
• Fits most sizes of bearing and
seals found on modern vehicles.
• Model No. VS7024
• List Price £249.95
FREE
8 Function Digital
Multimeter with
Thermocouple
•
•
£99.95 exc VAT
£119.94 inc VAT
• Suitable for installation/removal
of ignition coils on VAG vehicles.
• Long shafts with composite T-style
handle for added control and
stability.
• Prevents damage to ignition
coils whilst allowing faster
removal.
• Model No. VS5294
• List Price £49.95
FREE
Spark Plug Lead
Tool - VAG
Model No. VS5293
List Price £22.95
OFFER PRICE
£29.95 exc VAT
£35.94 inc VAT
Spark Plug Thread Repair Kit
FREE
4pc 3/8"Sq Drive Spark
Plug Socket Set
•
•
OFFER PRICE
Model No. AK6556
List Price £28.95
£129.95 exc VAT
£155.94 inc VAT
el
d
Mo
24
S6
.V
No
12
Model No.
Size
Length
VS624
12mm
260mm
VS625
14mm
260mm
o.
lN
de
Model No. AK865
List Price £4.45
• Suitable for five
common sizes of
thread.
• Creates a stronger
internal thread in soft
metals.
• Ideal for repairing damaged
or stripped internal threads.
• Protects tapped threads against
wear and damage.
• Includes drill bits, thread taps, insert
installation and lug breaking tools.
• Model No. TRMK
• List Price £109.95
• Suitable for straight installation
of bearing race without damage
to the bearing or axle housing.
• Fits most popular bearing race
sizes.
• Driver Sizes: 39.5, 44, 50, 59, 63,
64.5, 72, 76, 81mm
• Model No. VS703
• List Price £74.95
• A comprehensive set
for easy removal of
freewhee alternator
pulley, either on or off
the vehicle.
• Allows alternator shaft
to be held while pulley
retainer is removed.
• Model No. SX403
• List Price £124.95
5
Mo
•
•
£149.95 exc VAT
£179.94 inc VAT
23pc Alternator
Freewheel Pulley
Removal Set
Reverse Action Spark
Plug Thread Chasers
Spark Plug Boot
Puller Tongs
•
Model No.
TM100
List Price
£37.45
OFFER PRICE
£69.95 exc VAT
£83.94 inc VAT
10pc Bearing Race & Seal
Driver Set - Aluminium
• Comprehensive and time saving kit
of spark plug thread repair tools.
• Especially suitable for the
repair of deep-seated
plug configurations.
• Stepped tap ensures
correct alignment of
cutter in existing spark
plug hole.
• Extension tools allow easy
access to the bottom of the
plug recess.
• Model No. VS301
• List Price £199.95
• Specially designed
to repair damaged,
deep-seated spark
plug threads on
modern engines.
OFFER PRICE
Thread Repair
Master Kit
4pc Spark Plug Puller Set - VAG
each
FREE with
FREE
6 Function Professional
Digital Multimeter
•
OFFER PRICE
Model No.
MM20
List Price
£29.95
•
•
37pc Bearing & Seal
Installation Kit
2
S6
V
List Price Exc. VAT
Inc. VAT
£44.95
£29.95
£35.94
£46.95
£30.95
£37.14
NEW
OFFER PRICE
£39.95 exc VAT
£47.94 inc VAT
FREE
6pc Pick & Hook
Set Extra-Long
•
•
Model No. AK5215
List Price
£19.95
ARRIVING
OCTOBER
OFFER PRICE
£79.95 exc VAT
£95.94 inc VAT
Prices exclude VAT unless stated otherwise
Promotion Code: VST12.09
9pc Gasket Punch Set
FREE
15 Blade Feeler
Gauge - Metric
• Interchangeable hollow punch
set capable of punching holes in
gaskets, leather, paper, plastic,
wood sheet and other soft materials.
• Model No. AK708
• List Price £32.95
3pc Miniature
Brush Set
•
•
Model No. AK9791
List Price £3.95
FREE
3pc Miniature
Brush Set
•
•
Model No. AK9791
List Price £3.95
OFFER PRICE
£19.95 exc VAT
£23.94 inc VAT
26 Blade Offset Feeler
Gauge - Dual Marked
•
•
•
•
•
•
•
•
•
•
•
OFFER PRICE
Metric graduated, 15 blade, feeler gauge.
Sizes: 0.06 to 0.70mm.
Blade dimensions: 75 x 13mm.
Model No. VS511
List Price £8.95
£5.45
£6.54
exc VAT
inc VAT
Triple Leg Glaze Breaker
Ø50-175mm 75mm
Medium Stones
Imperial graduated 26 blade feeler gauge.
Sizes: 0.005" to 0.030"
Dual marked in Imperial and Metric.
Blade dimensions 75 x 13mm(45º-15mm offset).
Model No. VS515
List Price £21.95
OFFER PRICE
£14.45
£17.34
exc VAT
inc VAT
Valve Spring Compressor
OHC/OHV/CVH
• For removal of heat glaze and carbon deposits
on cylinder walls.
• Fitted with 75mm, medium grade cutting stones
and suitable for cylinders up to Ø175mm.
• Range collar adjusts arm travel between Ø50mm
and Ø100mm or Ø100mm and Ø175mm.
• Adjustable spring tension gives finish control.
• Model No. VS162
• List Price £46.95
OFFER PRICE
£29.95 exc VAT
£35.94 inc VAT
Pack of 3 75mm
Stones
FREE
2pc Valve Grinder Set
•
•
Model No. VS1653
List Price £9.95
l
de
• Application: VS162.
• Suitable for most small and medium sized OHC engines
and also for general use on OHV and CVH engines.
• Universal jaw with 60-155mm capacity and 160mm throat
depth.
• Model No. VS153
• List Price £37.95
OFFER PRICE
£24.95 exc VAT
£29.94 inc VAT
Mo
1
62
S1
.V
No
Model No.
Grade
Pack Quantity
List Price
Exc. VAT
Inc. VAT
VS1621
Medium
3
£9.75
£6.95
£8.34
VS1622
Coarse
3
£9.75
£6.95
£8.34
VS1623
Fine
3
£9.75
£6.95
£8.34
Stud Remover
& Installer
Mechanic's
Stethoscope
Universal Clutch
Alignment Tool
• Suitable for the removal
and installation of
various sizes of stud.
• Cam rotates to grip
onto the stud for
quick and easy use.
• Use with 1/2"Sq drive
ratchet wrench.
• Model No. VS7232
• List Price £12.95
• Quickly locates the source of engine noise such as
piston slap, worn gears and bearings, damaged
valves, water pump failure and blown gaskets and
even dash board squeaks.
OFFER PRICE
• Plastic ear pieces and
300mm probe with sound
exc VAT
amplifying chamber.
• Model No. AK871
inc VAT
• List Price £14.95
• Nylon components with steel main shaft.
• Fits 90% of cars and light vans up to
5tonne gross (not suitable for Minis (A Series)
or vehicles with double plate clutches).
• Suitable for front wheel
drive vehicles.
OFFER PRICE
• Supplied with 2 different
exc VAT
sized expanding collets.
• Model No. VS010
inc VAT
• List Price £15.95
Promotion Code: VST12.09
OFFER PRICE
£8.45
£10.14
exc VAT
inc VAT
£8.95
£10.74
Prices exclude VAT unless stated otherwise
£9.95
£11.94
13
Toyota Oil Filter Cap Wrench
30pc Oil Filter Cap
Wrench Set
NEW
• Model No.
VS7111
• List Price
£12.45
OFFER PRICE
£7.95
£9.54
inc VAT
NEW
Lexus/Toyota Oil Filter
Cap Wrench
• Model No.
VS7112
• List Price
£12.45
OFFER PRICE
£7.95
£9.54
exc VAT
inc VAT
NEW
Mercedes-Benz Oil Filter
Cap Wrench
• Model No.
VS7113
• List Price
£12.45
8-in-1 Oil Drain
Plug Wrench
•
•
£95.95 exc VAT
£115.14 inc VAT
exc VAT
inc VAT
ARRIVING
OCTOBER
• Model No.
VS7114
• List Price
£12.45
• Refractometer designed to measure aqueous/urea
content of AdBlue additive.
• Ensures AdBlue additive is correctly diluted before
adding to vehicle’s AdBlue tank.
• Measures refractive index of fluid
using only a drop of AdBlue.
OFFER PRICE
• Simple calibration check
using distilled water.
exc VAT
• Model No. VS0051
• List Price £89.95
inc VAT
OFFER PRICE
£6.95
£8.34
OFFER PRICE
£7.95
£9.54
Refractometer
AdBlue
• Designed to remove AdBlue
filter housing cap on BlueTec
engines, fitted to Mercedes
commercial vehicles.
• Model No. SX120
• List Price £10.95
NEW
Volvo Oil Filter Cap
Wrench
Model No. VS650
List Price £34.95
OFFER PRICE
3/8"Sq Drive Filter Wrench
46mm AdBlue-Mercedes
OFFER PRICE
£7.95
£9.54
FREE
• Extensive set designed for
a wide range of vehicles.
• Cap type filter wrenches,
made from 7 and 16
gauge steel, will withstand
up to 115Nm (85lb.ft) of
torque.
• Designed to grip like sockets,
thereby minimising the
possibility of crushed filters.
• Adaptor allows use with 3/8"
or 1/2"Sq drive wrenches.
• Adjustable oil filter wrench
Ø65-120mm.
• Model No. VS7006
• List Price £145.95
exc VAT
exc VAT
inc VAT
£59.95
£71.94
exc VAT
inc VAT
15pc 3/8"Sq Drive Magnetic
Oil Drain Plug Socket
& Key Set
Swivel Jaw Filter Pliers
Ø57-120mm Capacity
NEW
FREE
8ltr Oil/Fluid Drain Pan
•
•
• Jaws swivel up to 90º to give access to awkwardly
positioned oil and fuel filters.
• Chemically blackened finish to prevent corrosion
and non-slip grip for added comfort and control.
• Capacity: Ø57-120mm.
• Model No. AK6417
• List Price £44.95
Model No. DRP01
List Price
£8.45
OFFER PRICE
£28.95 exc VAT
£34.74 inc VAT
Band Type Oil Filter Wrenches
o.
lN
e
od
Low Profile Oil/Fluid
Drainer
OFFER PRICE
£54.95 exc VAT
£65.94 inc VAT
NEW
4
64
AK
M
o.
N
el
Model No.
Capacity
List Price
Exc. VAT
Inc. VAT
AK644
Ø65-110mm
£19.95
£12.95
£15.54
AK645
Ø105-155mm
£19.95
£12.95
£15.54
5
64
AK
d
Mo
14
• Each features magnetic retention
to prevent sump plugs from
accidently falling into drain pans.
• Suitable for use on engines,
gearboxes and back axles.
• Includes application chart.
• Contents: Square; 8, 10mm, Hex; 8,
10, 12, 13, 14, 17mm, TRX-Star*; T45,
Sockets; 13, 14, 17, 18, 19, 21mm.
• Model No. AK6588
• List Price £79.95
• Low profile design is
ideal for the professional
mechanic and DIY user.
• Ensures safe and clean
collection, transportation
and temporary storage of
waste fluids.
• Four castors provide easy
manoeuvrability.
• Includes grid to aid draining
of filters and to prevent debris
entering the tank.
• Model No. DRP011
• List Price £72.95
Prices exclude VAT unless stated otherwise
OFFER PRICE
£44.95 exc VAT
£53.94 inc VAT
Promotion Code: VST12.09
Ø74mm Oil Filter Cap Wrench
14 Flutes
3pc Oil Filter Cap Wrench Set - Renault
• Cap type filter wrenches for vehicles fitted with
Renault dCi engines 1.5, 1.9, 2.2 and 2.5.
• Also compatible with some Nissan
and Vauxhall/Opel vehicles.
• Sizes: 27, 76, 96mm.
• Model No. VS7001
• List Price £27.95
• Will withstand up to 115Nm (85lb.ft) of torque.
• Applications: Purlux grove filters fitted to Audi,
BMW, Citroen, Fiat, Ford, Lancia, Mazda,
Mercedes-Benz, Nissan, Peugeot, Porsche,
Renault, Suzuki, Toyota, Vauxhall/Opel, VW.
• Model No. SX226
• List Price £15.95
OFFER PRICE
OFFER PRICE
£9.95
£11.94
£17.95
£21.54
exc VAT
inc VAT
Sump Separator
inc VAT
46mm Differential Filter
Spanner - VAG
• Designed to separate the engine or gearbox
sump without damaging the sump.
• Thin blade allows for the seal to be broken
by lightly tapping the body with a hammer.
• Features two handle locations making it
ideal for use in confined engine spaces.
• Model No. VS664
• List Price £15.95
OFFER PRICE
£9.95
£11.94
exc VAT
inc VAT
• Specially designed
for removing and
installing differential
filters.
• Suitable for use on
Audi; TT, Seat, Skoda,
VW; 4Motion Golf
and Passat.
• Model No. SX150
• List Price £32.95
Oil Filter Wrench Claw Type 1/2"
& 3/8"Sq Drive 65-110mm
Capacity
Oil Filter Strap Wrench
3/8" & 1/2"Sq Drive
300mm Capacity
• Model No. AK643
• List Price £16.95
• Satin finish cast steel body
with 3/8" and 1/2"Sq drives.
• May also be used with a
21mm (13/16") spanner.
• Extra wide Nylon webbing
strap suitable for filters up
to Ø300mm.
• Model No. AK6403
• List Price £15.45
OFFER PRICE
£8.45
£10.14
exc VAT
exc VAT
inc VAT
OFFER PRICE
£22.95 exc VAT
£27.54 inc VAT
Oil Filter Drain
Tube - VAG FSi
OFFER PRICE
£8.95
£10.74
exc VAT
inc VAT
• Designed to attach to the
oil filter housing on VAG FSi
petrol engines.
• Allows the filter housing to
be drained before removal,
preventing spillage.
• Use in conjunction with
a suitable oil drainer.
• Model No. VS7010
• List Price £24.95
OFFER PRICE
£15.95 exc VAT
£19.14 inc VAT
534pc Sump Plug &
Washer Assortment
Oil Drain Plug Master
Thread Repair Kit
FREE
120pc Automotive
Fuse Assortment
•
•
• Set is suitable for the most popular threads
used on cars and light commercial vehicles.
• Sizes: M13 x 1.25, M13 x 1.5, M15 x 1.5,
M17 x 1.5, M20 x 1.5, M22 x 1.5mm.
• Model No. VS661
• List Price £124.95
OFFER PRICE
£69.95 exc VAT
£83.94 inc VAT
• Sump Plugs: M10 x 1.0, M12 x 1.5, M13 x 1.5, M14 x 1.5,
M15 x 1.5, M16 x 1.5, M18 x 1.5, M20 x 1.5mm.
• Model No. VS663
• List Price £69.95
Mercedes Transmission Dipsticks
Oil Seal Removal/Installation Kit
• Made from spring steel
with plastic measuring
tip for accurately
checking the fluid
level.
• Comprehensive kit for the removal
and installation of oil seals without
damaging the new seal or housing.
• Kit includes a seal removal puller
and seven adaptors to fit most
sizes of seal.
• Designed to allow original
pulley/flange bolt to be
used to press in the
new seal, ensuring
a squarely seated
seal every time.
• Model No. VS7002
• List Price £145.95
Model No.
D
lN
de
Mo
V
o.
0T
20
S1
o
lN
de
Mo
D
0T
92
S
.V
Transmission Code
List Price
Length
Exc. VAT
Inc. VAT
VS920TD
716.5, 722.7, 722.8
£29.95
920mm
£17.95
£21.54
VS1200TD
722.6
£29.95
1200mm
£18.95
£22.74
Promotion Code: VST12.09
OFFER PRICE
£99.95 exc VAT
£119.94 inc VAT
Prices exclude VAT unless stated otherwise
Model No. BCF120
List Price £13.45
OFFER PRICE
£49.95 exc VAT
£59.94 inc VAT
FREE
8-in-1 Oil Drain
Plug Wrench
•
•
Model No. VS650
List Price £34.95
15
25pc Cooling System
Pressure Test Kit
NEW
Cooling System
Vacuum Purge
& Refill Kit
FREE
Antifreeze Tester
Tube Type
•
•
FREE
9pc Hose Clip Removal
Tool Set
•
•
Model No. VS1662
List Price £124.95
• Traditional style cooling system pressure testing kit.
Features five new adaptors increasing the vehicle
applications. Suitable for Alfa, Audi, BMW, Chrysler,
Citroen, Daewoo, Fiat, Ford, Honda, Hyundai, Kia,
Lancia, Mazda, Mercedes, Mitsubishi, Nissan,
Peugeot, Renault, Rover, Saab, Seat, Skoda, Suzuki,
Toyota, Vauxhall/Opel, Volvo, VW. Also includes
non-specific adaptors for other makes.
• Model No. VS0011
• List Price £329.95
£199.95 exc VAT
£239.94 inc VAT
20pc Cleaning &
Decarbonising
Brush Set
Oxygen Sensor Port
Thread Chaser
M18 x 1.5mm
•
•
• Ideal for cleaning and decarbonising areas
with limited access, especially glow plug and
injector apertures before refitting.
• Supplied in sizes from Ø9-19mm in brass,
nylon and steel.
• Features quick-release extension bar for
increased reach.
• Model No. VS1800
• List Price £35.95
Model No. VS528
List Price £8.95
OFFER PRICE
£22.95 exc VAT
£27.54 inc VAT
32
Antifreeze Testers
Twin-Rotor
Mo
o.
N
el
1
03
VS
• Features a temperature
compensation rotor that
automatically adjusts the
reading regardless of the
coolant temperature.
• Freeze protection level is
indicated on the scale in
degrees Celsius.
d
Mo
o
lN
30
S0
.V
de
Mo
• Smooth rounded jaw edges prevent damage
to internal hose reinforcement.
• Quick and simple - one handed use.
• Made from durable glass reinforced nylon.
Model No.
Application
Size
VS030
Brake & Fuel Hoses
Small
VS031
Heater Hoses
VS032
Radiator Hoses
List Price
Exc. VAT
Inc. VAT
£8.25
£5.45
£6.54
Medium
£9.25
£5.95
Large
£12.45
£7.95
o.
lN
de 1
Mo S412
V
Type
List Price
Exc. VAT
Inc. VAT
£7.14
VS4120
Ethylene
£21.95
£14.95
£17.94
£9.54
VS4121
Propylene
£21.95
£14.95
£17.94
Radiator Fin
Straightener
• Suitable for synthetic antifreeze mixtures including
long life OAT (Organic Acid Technology).
• Temperature corrected
prism ensures accuracy.
OFFER PRICE
• Eyepiece with adjustable
exc VAT
focus.
• Model No. VS005
inc VAT
• List Price £99.95
• Allows removal of any small debris build
up that can gather between the fins.
• Six different comb sizes.
• Also suitable for domestic
and industrial air
OFFER PRICE
conditioning and heat
exc VAT
exchange applications.
• Model No. VS0472
inc VAT
• List Price £7.95
£59.95
£71.94
o.
lN
de 0
Mo S412
V
Model No.
Refractometer Antifreeze/Battery
Fluid/Screenwash
16
£59.95 exc VAT
£71.94 inc VAT
OFFER PRICE
S0
.V
No
OFFER PRICE
• Dramatically reduces cooling system refill time,
without mess and without introducing air-locks.
• Model No. VS0042
• List Price £85.95
FREE
Composite Hose Pinch Tools
l
de
Model No. AK413
List Price £9.45
NEW
£4.45
£5.34
Prices exclude VAT unless stated otherwise
Brake & Fuel Hose Pinch
Tool - Bar Type
• Suitable for both brake and fuel lines.
• Simple, yet effective pinch action with
rounded clamp section to prevent
damage to hose lining.
• Metal construction with
OFFER PRICE
chromed finish.
exc VAT
• Model No. VS033
• List Price £17.95
inc VAT
£9.95
£11.94
Promotion Code: VST12.09
Exhaust Fume Extraction Systems 230V - 370W
Model No. EFS101
•
•
•
•
•
Model No. EFS102
Wall mounting electric fan fitted with heat resistant ducting and exhaust pipe
cone with exhaust gas analyser port.
Ideal for bikes, cars and car derived vans.
Requires installation onto workshop wall and ducting to expel exhaust gases.
Does not include electrical switch gear.
Ideal for smaller garages and workshops where space is limited.
5pc Oxygen Sensor
& Thread Chaser
Set
OFFER PRICE
£25.95 exc VAT
£31.14 inc VAT
• Model No. SX0320
• List Price £39.95
EFS101
EFS102
Type
Motor
Single Hose 370W - 230V 50Hz
Twin Hose
370W - 230V 50Hz
List Price
Exc. VAT
Inc. VAT
£1345.95
£899.95
£1079.94
£1795.95
£1199.95
£1439.94
Ratcheting Exhaust
Pipe Cutter
3pc Exhaust Pipe
Expander Set
• Cuts up to 3mm thick and
is suitable for the toughest
materials including
stainless steel exhaust
pipes.
• Model No. VS16371
• List Price £139.95
• Ideal for fitting aftermarket
components to standard
exhausts.
• Sizes: Small; 30-44mm,
Medium; 38-62mm,
Large; 54-87mm.
• Model No. VS1668
• List Price £99.95
FREE
9pc Hose Clip
Removal Tool
Set
Model No.
OFFER PRICE
£89.95 exc VAT
£107.94 inc VAT
• Manufactured to CAT 2 BS EN 388 and BS EN 407
from 100% DuPont Kevlar®.
• Designed for use in engine bays to prevent cuts
to forearms and burns from exhausts and other
hot components.
• Thumb slot design ensures sleeve will stay in position.
Model No.
Length
List Price Exc. VAT
SSP36
355mm
£11.95
£6.95
£8.34
SSP37
460mm
£14.95
£8.45
£10.14
Promotion Code: VST12.09
•
•
£65.95 exc VAT
£79.14 inc VAT
• Set comprises full length and kneeler mats.
• For use on workshop floors when working
on wheels, brakes, tyres and exhausts etc.
• Also ideal for roadside repairs.
• Sizes: Kneeler; 385 x 280 x 22mm,
Full-length; 890 x 390 x 22mm.
• Model No. VS857
• List Price £34.95
Inc. VAT
Model No. DRP01
List Price £8.45
OFFER PRICE
£19.95 exc VAT
£23.94 inc VAT
2pc Exhaust
Puller Tool Set
Exhaust Doughnut Puller
Kevlar Hot Sleeves
FREE
8ltr Oil/Fluid Drain Pan
Model No. DRP04
List Price £25.95
OFFER PRICE
• All the hose clip tools you are likely to need in one case.
• Model No. VS1662
• List Price £124.95
£59.95 exc VAT
£71.94 inc VAT
Mechanic's Mat Set EVA - 22mm
17ltr Antifreeze/Fluid
Drain Pan
•
•
OFFER PRICE
• Steel construction with dipped vinyl handle.
• Enables fast removal
and installation of rubber
OFFER PRICE
anti-vibration mountings
found on modern exhaust
exc VAT
systems.
• Model No. VS163
inc VAT
• List Price £8.45
£4.95
£5.94
Prices exclude VAT unless stated otherwise
• Invaluable when installing exhaust systems.
• T-handled tools allow easy fitting of exhaust
mounts.
• One straight and one
OFFER PRICE
hooked to suit block
and ring mounts
exc VAT
respectively.
• Model No. VS1641
inc VAT
• List Price £13.45
£8.85
£10.62
17
Petrol Engine Setting/
Locking Kit Alfa Romeo,
Fiat 1.4 - MultiAir
Belt Drive
Diesel Engine Timing Overhaul
Kit - Alfa Romeo, Fiat, Ford,
Lancia, Suzuki, Vauxhall/Opel
1.3 JTD/TDCi - Chain Drive
• The MultiAir engine
replaces the inlet camshaft
with an electro/hydraulic system
operating the inlet valves.
• This kit is required to set the engine
timing when carrying out belt replacement.
• Features a camshaft setting plate, crankshaft
locking tool and tensioner adjuster.
• Model No. VS5050
• List Price £119.95
• This range of Fiat 1.3 16v diesel
engines, used by a number of
vehicle manufacturers, are all
twin camshaft, common rail diesels.
• The chain drive connects the crankshaft
to the exhaust camshaft which in turn is
connected by gears to the inlet camshaft.
• The overhaul kit is designed to minimise the level
of disassembly so the cylinder head/camshafts
can be removed without removing the front-end
timing cover, sprockets and timing chain.
• Model No. VS5080
• List Price £199.95
OFFER PRICE
£79.95 exc VAT
£95.94 inc VAT
Petrol Engine Setting/Locking
Kit - Fiat, Lancia 1.6 16v
Belt Drive
OFFER PRICE
£139.95exc VAT
£167.94 inc VAT
Diesel Engine Setting/Locking
Kit - Fiat 1.7/1.9D/TD
Belt Drive
NEW
ARRIVING
OCTOBER
• Suitable for timing belt
replacement on 1.7/1.9
Fiat vehicles.
• Features camshaft locking
plates and crankshaft timing tool.
• Model No. VSE2512
• List Price £109.95
• Kit contains inlet and exhaust
camshaft setting plates and a
timing belt tensioner adjuster.
• TDC Position on these twin cam
engines is established using
VSE2515 TDC Positioning Tool
and AK9634M Dial Gauge.
• Model No. VSE2513
• List Price £129.95
TDC Position Tool
Alfa Romeo, Fiat
• Used in conjunction with Model
No. AK9634M dial gauge (not
included) and enables accurate
interpretation of piston position
relative to TDC.
• Model No. VSE2515
• List Price £39.95
£89.95 exc VAT
£107.94 inc VAT
NEW
Petrol Engine Setting/
Locking Kit - Fiat, Ford,
Lancia 1.2, 1.4 8v
Belt Drive
NEW
£26.95 exc VAT
£32.34 inc VAT
• Kit consists of camshaft setting
plate, crankshaft locking tool
and belt tensioner adjuster for
the 1.2 engine.
• Additional sprocket locking tool
and alignment fixture for the
camshaft sensor on the 1.4 VVT
engine.
• Model No. VSE5061
• List Price £99.95
OFFER PRICE
£69.95 exc VAT
£83.94 inc VAT
Petrol Engine Setting/Locking
Kit - Fiat, Lancia 1.6
16v Belt Drive
Petrol Engine Setting/Locking
Kit - Alfa Romeo Twin Spark
1.4, 1.6, 1.8, 2.0 16v Twin
Cam - Belt Drive
18
£64.95 exc VAT
£77.94 inc VAT
OFFER PRICE
OFFER PRICE
• Kit includes camshaft setting
plates for locking the
camshafts in the timed
position.
• The plates are positioned
in place of the camshaft
bearing caps.
• The kit also includes timing
and balance shaft belt
tensioner adjusters.
• TDC positioning tools are
also required to time these
engines, not supplied in kit.
• Model No. VSE2510
• List Price £139.95
OFFER PRICE
OFFER PRICE
£99.95 exc VAT
£119.94 inc VAT
• Kit consists of Camshaft
Setting Plates and a special
timing belt tensioner adjuster.
• Model No. VS1402
• List Price £222.95
Prices exclude VAT unless stated otherwise
OFFER PRICE
£157.95 exc VAT
£189.54 inc VAT
Promotion Code: VST12.09
Diesel Engine Setting/
Locking Kit - BMW, Land
Rover, Vauxhall/Opel
M41, M51 - Chain
Drive
Diesel Engine Setting/Locking Kit - Alfa
Romeo, Fiat, Ford, Lancia, Suzuki,
Vauxhall/Opel 1.3D JTD(M)/
TDCi/DDiS/CDTi 16v
Chain Drive
NEW
NEW
• Suitable for timing the camshaft
and crankshaft, on chain drive
1.3 diesel engines.
• Set also includes a tensioner
locking pin.
• Model No. VSE5881A
• List Price £59.95
OFFER PRICE
£39.95 exc VAT
£47.94 inc VAT
Diesel Engine Setting/
Locking Kit - Jaguar,
Land Rover 2.7 V6
Belt Drive
£84.95 exc VAT
£101.94 inc VAT
NEW
OFFER PRICE
£44.95 exc VAT
£53.94 inc VAT
• For use with twin vanos
variable valve/timing units
on six cylinder BMW engines.
• Designed for dismantling/assembling
and timing of the unit after engine
overhaul/repair work.
• Used in conjunction with Model No. VS4425
Setting/Locking Tool Kit for engine timing.
• Model No.VSE5906
• List Price £124.95
Petrol Engine Setting/Locking Kit Land Rover, MG, Rover 2.0, 2.5
KV6 - Belt Drive
Diesel Engine Setting/Locking
Kit - Land Rover 2.5D Td5
Chain Drive
• Set comprises flywheel locking pin (threaded) and camshaft
locking pin to cover engine timing on the Land Rover
Td5 engines in Defender and Discovery models.
• Model No. VSE5986
• List Price £14.95
Injection & HP Pump Remover/
Sprocket Retainer - BMW M47,
M57, Land Rover (Td6),
Vauxhall/Opel
NEW
OFFER PRICE
£9.95
£11.94
exc VAT
inc VAT
£84.95 exc VAT
£101.94 inc VAT
FREE
Petrol Engine Camshaft
Setting Plates - MG 2.0,
2.5 KV6 (190) - Belt Drive
Model No. VS4617
List Price £36.95
OFFER PRICE
£319.95 exc VAT
£383.94 inc VAT
Injection & HP Pump Remover/
Sprocket Retainer M47R Land
Rover, Rover/MG
• For engine timing use
Setting/Locking Kit
Model No. VSE5666.
OFFER PRICE
•
•
• Kit includes all engine
timing belt replacement
tools for the 2.0 and 2.5
variants of the KV6 quad
cam engine.
• Applications: Rover: 825
(96-99), 45, 75 (99on)
Land Rover: Freelander
(00on).
• Model No. VS1290
• List Price £462.95
NEW
NEW
Flywheel Locking
Tool
• Model No: VSE5665
• List Price £39.95
• Model No. VSE5664
• List Price £39.95
OFFER PRICE
£25.95 exc VAT
£31.14 inc VAT
Promotion Code: VST12.09
OFFER PRICE
Petrol Engine Twin Vanos
Service Kit - BMW M52TU,
M54, M56
• Setting and locking kit for
2.7 diesel belt drive engines,
fitted to both Land Rover and
Jaguar vehicles.
• Kit contains camshaft alignment/
timing pins and flywheel locking
tools.
• Model No. VSE5000
• List Price £67.45
• For engine timing use
Setting/Locking Kit
Model No. VSE5666.
• Kit includes camshaft setting plate and
TDC location pin which are required to
‘set’ and ‘lock’ the specified 1.7 and 2.5
diesel engines in the timing position.
• The kit also contains timing chain tensioner
retaining pins (pair), tensioner compression
lever and injection pump remover/sprocket
retainer which is used to retain and support
the sprocket and timing chains in position
when the pump has been removed.
• Model No. VSE5522
• List Price £124.95
OFFER PRICE
£25.95 exc VAT
£31.14 inc VAT
Prices exclude VAT unless stated otherwise
• Used to lock the flywheel so the bottom pulley bolt
can be loosened or tightened, which is usually
necessary when replacing the timing belt.
• Removal of the starter motor or gearbox
may be required for
fitment of the tool.
OFFER PRICE
• Adjustment on the
tool allows it to fit
exc VAT
most vehicles.
• Model No. VS778
inc VAT
• List Price £59.95
£39.95
£47.94
19
Diesel/Petrol Engine Setting/
Locking Master Kit - Ford
Belt - Chain Drive
• Master kit of setting & locking
tools suitable for a wide range
of modern Ford vehicles.
• Also suitable for some Mazda
vehicles.
• Model No. VSE5042
• List Price £154.95
Petrol Engine Setting/Locking Kit
Ford, Mazda - Belt - Chain Drive
OFFER PRICE
£115.95 exc VAT
£139.14 inc VAT
Diesel Engine
Setting/Locking
Tool Set - Ford
TDCi, Mazda D
1.4, 1.6, PSA
HDi - Belt Drive
• Features timing pins to lock and
hold the camshaft and crankshaft
in the timed position.
OFFER PRICE
• Flywheel locking tool can
also be used for Ford
exc VAT
Mondeo/Transit vehicles.
• Model No. VSE5846B
inc VAT
• List Price £22.95
£16.95
£20.34
• Includes revised design camshaft setting
plate and tensioner locking pin.
• This kit covers the complete range of Ford
Duratec engines 1.25 through to 2.0 16v
in both belt and chain drive variants.
• Pins also suitable for some Mazda vehicles.
• Model No. VSE5515
• List Price £22.45
OFFER PRICE
£15.95 exc VAT
£19.14 inc VAT
Auxiliary Stretch Belt
Removal/Installation
Tool
Diesel/Petrol Engine Crankshaft/
Camshaft Locking Pin Set
Renault 1.5, 1.8, 1.9,
2.0 - Belt Drive
• Designed for the recommended
removal and installation of
elasticated or stretch drive
belts fitted to modern
auxiliary drive systems such
OFFER PRICE
as the alternator or power
exc VAT
steering.
• Model No. VS787
inc VAT
• List Price £49.95
• Set of camshaft and crankshaft locking pins
for Renault diesel and petrol engines.
• Suitable for locking engine during cam belt
replacement or during
OFFER PRICE
associated engine
maintenance.
exc VAT
• Model No. VSE1901
• List Price £24.95
inc VAT
£33.95
£40.74
Petrol Engine Setting/Locking Kit
Renault 1.4, 1.6, 1.8, 2.0 16v
K4J, K4M, F4P, F4R(t) - Belt Drive
£15.95
£19.14
Diesel Engine Locking Kit - Nissan,
Renault dCi, Vauxhall/Opel 1.5,
1.9, 2.2, 2.5Di/DTi/CDTi
Belt Drive
NEW
• Updated kit suitable for timing belt
replacement on 1.4, 1.6, 1.8 and
2.0 engines fitted in Renault vehicles.
• These engines will require the use of
associated tool, Model No. VSE5034
or VSE5734 Camshaft Sprocket Holding
Tool, to loosen the camshaft sprocket
bolts.
• Kit features updated camshaft setting
plate which avoids the camshaft position
sensor on later 1.4 and 1.6 engines.
• Model No. VSE5071A
• List Price £79.95
Petrol Engine Camshaft Setting
Tool - VAG 1.4, 1.6 Belt Drive
OFFER PRICE
£54.95 exc VAT
£65.94 inc VAT
• Essential tools for timing belt
replacement on a wide range
of Renault, Nissan & Vauxhall/
Opel diesel engines.
• Model No. VSE5871
• List Price £194.95
OFFER PRICE
£129.95 exc VAT
£155.94 inc VAT
Belt Guide Roller Adjuster
Vauxhall/Opel V6
• Suitable for VW 1.4 and 1.6
twin camshaft/twin belt
engines introduced in 1997.
• Model No. VS1246
• List Price £72.95
OFFER PRICE
£44.95 exc VAT
£53.94 inc VAT
20
• Suitable for adjusting the
position of the upper and
lower guide rollers on the
Vauxhall/Opel V6 EcoTec engine.
• Helps ensure that the timing belt is taut during
installation and to assist initial belt tension.
• Model No. VS1301
• List Price £62.45
Prices exclude VAT unless stated otherwise
OFFER PRICE
£34.95 exc VAT
£41.94 inc VAT
Promotion Code: VST12.09
Diesel Engine Camshaft
Sprocket Hub Remover/
Installer Set - VAG - Belt
Drive
Diesel Engine Setting/Locking
Kit VAG 2.5TDi V6 - Belt Drive
NEW
• Suitable for the VAG 2.5 V6 diesel
engines first introduced in 1997.
• Includes front end support guides,
crankshaft locking pin, camshaft
setting plates, injection pump
locking pin, tensioner socket and
tensioner locking pin.
• Model No. VSE2351
• List Price £64.95
NEW
OFFER PRICE
£44.95 exc VAT
£53.94 inc VAT
• Essential tool required when
removing the cylinder head/
camshafts on VAG Pumpe
Duse and common rail
diesels.
• Set comprises camshaft
sprocket hub holding tool
and hub remover.
• Model No. VSE5952
• List Price £59.95
ARRIVING
OCTOBER
OFFER PRICE
£39.95 exc VAT
£47.94 inc VAT
Diesel Engine Setting/Locking
Kit VAG Pumpe Duse 1.2,
1.4, 1.9 - Belt Drive
Diesel Engine Balance Shaft
Locking Set VAG 2.0 Pumpe
Duse - Belt Drive
NEW
• Special tools required during removal/
installation of the balance shaft on
certain VAG 2.0 Pumpe Duse diesel
engines.
• Set comprises balance shaft locking
tool and chain tensioner locking pin.
• These engines are a belt drive with
the balance shaft driven separately
by a chain.
• Model No. VSE5953
• List Price £17.95
OFFER PRICE
£11.95
£14.34
exc VAT
inc VAT
Diesel Engine Setting/Locking
Kit - VAG Pumpe Duse 1.2,
1.4, 1.9, 2.0TDi PD
Belt Drive
• Setting and locking kit for a range of
VAG vehicles with Pumpe Duse TDi PD
(1.9).
• Contents: Injection pump locking pin,
locking tensioner tool and crankshaft
locking tool.
• Model No. VSE2356
• List Price £19.95
OFFER PRICE
£11.95
£14.34
exc VAT
inc VAT
Diesel/Petrol Camshaft Sprocket
Remover VAG 1.9, 2.4, 2.5,
2.7, 2.8 - Belt Drive
Also 1.6, 2.0
common rail
• Suitable for belt replacement
on Pumpe Duse diesel engines
fitted to VAG vehicles and Ford
Galaxy from 1999 on.
• Kit contains both crank locking tools
for ‘Round’ and ‘Oval’ crankshaft gears,
camshaft pins and tensioner tools for
hydraulic and mechanical belt tensioners.
• Model No. VSE5951
• List Price £129.95
OFFER PRICE
£84.95 exc VAT
£101.94 inc VAT
FREE
Mini Digital
Thermometer
• Model No. VS906
• List Price £17.95
Promotion Code: VST12.09
OFFER PRICE
£47.95
£57.54
exc VAT
inc VAT
16pc Setting/Locking Tool Kit
9pc Belt Tensioner
Wrench Set
• Interchangeable auxiliary and timing
pulley belt tensioner wrench set.
• A time saving and effective method
for the professional technician.
• Sizes: 12-19mm.
• Model No. VS789
• List Price £119.95
• Specially designed to remove
camshaft sprockets with 5 and 6
spokes from Audi, Skoda and VW
vehicles.
• Features ball end thrust screw to
reduce damage to camshaft bolt.
• Model No. VSE5959
• List Price £69.95
OFFER PRICE
£79.95 exc VAT
£95.94 inc VAT
• Updated kit of camshaft, crankshaft
and flywheel locking tools with
wide general coverage.
• Applications: Audi,
Citroen, Fiat,
Ford,
Peugeot,
Renault,
Rover, Saab,
Seat, Skoda,
Vauxhall/Opel, VW.
• Model No. VSE180
• List Price £132.95
OFFER PRICE
£79.95 exc VAT
£95.94 inc VAT
Prices exclude VAT unless stated otherwise
FREE
8 Function
Digital
Multimeter
with
Thermocouple
• Model No. MM20
• List Price £29.95
21
Front Wheel Bearing GEN2 Removal/Installation Kits
GEN 1
Double row
contact
bearing.
• Designed for the second generation of wheel bearings found on
modern vehicles.
• These bearings are lightweight with an integral mounting flange.
• They are also pre-loaded with a retaining ring that secures the
bearing into the housing.
• Suitable to be used in situ when replacing the front wheel bearings.
• Supplied in carry-case.
NEW
GEN 2
Hub unit with
bearing
(Single Flange).
GEN 3
Hub unit with
bearing
(Double Flange).
62mm Front Wheel
Bearing GEN2
Removal/
Installation
Kit
• Applications:
Audi; A2 1.2TDi
PD (01-05), VW;
Lupo 3L 1.2TDi
PD (01-06).
• Model No. VS7027
• List Price £299.95
OFFER PRICE
£199.95 exc VAT
£239.94 inc VAT
72mm Front Wheel
Bearing GEN2
Removal/
Installation
Kit
• Applications: Audi;
A1 (2010-on), A2
(00-05), Seat; Cordoba
(03-09), Ibiza (02-12),
Skoda; Fabia (00-12),
Roomster (06-12), VW;
Fox (05-10), Polo (02-12).
• Model No. VS7029
• List Price £299.95
OFFER PRICE
£199.95 exc VAT
£239.94 inc VAT
22
66mm Front Wheel
Bearing GEN2
Removal/
Installation
Kit
• Applications:
Skoda; Fabia
(00-12), VW; Fox
(05-10), Polo (02-09)
• Model No. VS7028
• List Price £299.95
OFFER PRICE
£199.95 exc VAT
£239.94 inc VAT
78mm Front Wheel
Bearing GEN2
Removal/
Installation
Kit
• Applications: Ford;
C-Max (07-11), Focus II
(04-11), Focus C-Max (03-07),
Mazda; 3 (03-05), Volvo; C30
(06-10), C70 (05-10), S40 (0412), V50 (04-10).
• Model No. VS7030
• List Price £349.95
FREE
With Each Kit
18pc Brake Piston
Wind-Back Tool Kit
• Model No. VS0282
• List Price £129.95
OFFER PRICE
£239.95exc VAT
£287.94 inc VAT
Prices exclude VAT unless stated otherwise
Promotion Code: VST12.09
FREE
Optical Wheel Alignment Gauge
Steering Rack
Knuckle Tool
•
•
• Steel and cast aluminium
construction.
• Measures toe-in and toe-out by contact with wheel rims and
optical sight to alignment markers.
• Works on practically all cars and light commercial vehicles
with rim diameters between 200mm and 600mm.
• Model No. GA40
• List Price £769.95
Model No. VS4000
List Price £24.95
Steering Turntables Pair
• Measures up to 45º rotation
in either direction.
• Maximum loading 1360kg
per pair.
• Model No. GA44
• List Price £329.95
FREE
Magnetic Camber/
Castor Gauge
OFFER PRICE
•
•
OFFER PRICE
£499.95 exc VAT
£599.94 inc VAT
£245.95exc VAT
£295.14 inc VAT
Model No. GA45
List Price £54.95
Professional Coil Spring
Compressor Set
1000kg Capacity
2pc Coil Spring
Compressor
• Hardened carbon
steel lead screws
and cast jaws.
• Use with 1/2"Sq drive
wrench.
• 230mm Maximum
jaw opening.
• Model No. AK3841
• List Price £36.95
• Suitable for
MacPherson
strut coil springs.
• Features a yoke
extension bracket
that also allows
use on conical springs.
• Supplied with three
pairs of different sized
interchangeable yokes,
for a wide range of vehicle
applications and plastic yoke
protectors that protect the
spring coating from damage
which can invalidate the
vehicle manufacturer's warranty.
• Model No. RE229
• List Price £499.95
OFFER PRICE
£22.95 exc VAT
£27.54 inc VAT
FREE
35pc 1/2”Sq Drive
WallDrive® Socket Set
Metric
OFFER PRICE
£299.95exc VAT
£359.94 inc VAT
•
•
Model No. S0914
List Price
£107.45
Coil Spring Compressing Stations - 1500kg Capacity
2pc Heavy-Duty
Coil Spring
Compressor Set
• Quicker and easier than using ratchet driven spring compressor.
• Plastic coated yokes reduce the risk of spring slippage/damage.
• Suitable for springs from Ø102mm to Ø160mm.
• Heavy-duty coil
spring compressor
with hardened steel
body and force screw.
• Ensures smooth
compression of spring.
• Maximum Capacity
per Pair: 1000kg.
• Model No. AK3845
• List Price £129.95
OFFER PRICE
£94.95 exc VAT
£113.94 inc VAT
4pc Subframe Locating
Pin Set - VAG
NEW
• Set of four subframe
locating pins allows
precise alignment of
the subframe to the
vehicle's chassis.
• Compatible with
a wide variety of
Audi and VW vehicles.
• Model No. VS3900
• List Price £34.95
FREE
4pc Mini Hook Set
OFFER PRICE
£22.95 exc VAT
£27.54 inc VAT
Promotion Code: VST12.09
•
•
Model No. AK521
List Price £8.45
• Model No. RE231
• List Price £314.95
OFFER PRICE
£189.95exc VAT
£227.94 inc VAT
Prices exclude VAT unless stated otherwise
• Model No. RE232
• List Price £374.95
OFFER PRICE
£219.95 exc VAT
£263.94inc VAT
23
Mercedes Lower Ball Joint
Remover/Installer
Wheel Bearing Removal/
Installation Kit
• Comprehensive kit for the fast
and effective removal and
installation of wheel
bearings on
front-wheel
drive
vehicles.
• Reduces
chances of
damage to hub
and bearing.
• Model No. VS7020
• List Price £274.95
OFFER PRICE
£169.95 exc VAT
£203.94 inc VAT
FREE
2pc Coil
Spring
Compressor
•
•
Model No.
AK3841
List Price
£36.95
• Suitable for the in
situ removal and
installation of front
lower ball joints on
W220, W211 & W230
Mercedes.
• Includes all necessary
adaptors.
• Use with ratchet wrench.
• Model No. VS1272
• List Price £274.95
OFFER PRICE
£169.95 exc VAT
£203.94 inc VAT
Front Disc Removal
Tool Kit - Ford Transit
Hydraulic HGV Ball
Joint Separator
• Suitable
for removal
of Ford Transit
(2000on) brake
discs.
• Simple mechanical
action makes removal
of bound-on or stubborn
discs fast and easy.
• Kit comprises of extra-long
forged steel legs, triple yoke
and force screw.
• Model No. VS1271
• List Price £189.95
• Forged steel body ball
joint splitter suitable for
light commercial vehicles.
• Specially designed to
be operated manually
or by 1.5tonne hydraulic
ram supplied.
• Model No. VS3811
• List Price £94.95
OFFER PRICE
£119.95 exc VAT
£143.94 inc VAT
Universal CVJ Boot
Clamp Kit
Ball Joint
Remover
• Fast and simple to use.
• Kit includes 56mtr* of high
quality stainless steel
banding with a tensile
strength of 420N/mm2.
• Dispenser case also
houses 150* clamp sets
and unique pliers with
integrated cutters and
band tensioner.
• Never be caught without the
right sized boot clamp again.
• Model No. BSL102
• List Price £56.95
• Chemically blackened forged
steel body with thrust bolt.
• Suitable for most small cars and
light vans.
• Jaw Capacity: 19mm.
• Model No. AK381
• List Price £18.95
OFFER PRICE
OFFER PRICE
£39.95 exc VAT
£47.94 inc VAT
5pc 1/2"Sq Drive
Impact Hub Nut
Socket Set
• Heavy-duty, high quality,
Chrome Molybdenum
impact sockets suitable
for use with any 1/2"Sq
drive impact tool.
• Blackened finish for
added corrosion resistance.
• Tool suitable for hub nut
applications where high
torque is required.
• Contents: 30, 32, 34, 35, 36mm.
• Model No. SX050
• List Price £74.95
OFFER PRICE
£39.95 exc VAT
£47.94 inc VAT
24
* Approximate quantities
FREE
4pc 1/2"Sq Drive
Alloy Wheel Impact
Socket Set
£10.95 exc VAT
£13.14 inc VAT
•
•
Model No. SX030
List Price
£49.95
OFFER PRICE
£59.95 exc VAT
£71.94 inc VAT
Ball Joint
Separator
• Forged steel body with satin finish.
• Suitable for most small cars and
light vans.
• Model No. AK382
• List Price £12.45
OFFER PRICE
£6.45
£7.74
exc VAT
inc VAT
Ball Joint Splitter Hydraulic
& Manual - HGV
• Specially designed to be operated
manually or by 12tonne
hydraulic ram supplied.
• Features a step
down thread
adaptor that
allows fitting
of the manual
thrust screw or
hydraulic ram.
• Hydraulic ram
interchangeable
with Model No. PS990.
• Model No. VS3813
• List Price £199.95
OFFER PRICE
£139.95 exc VAT
£167.94 inc VAT
Prices exclude VAT unless stated otherwise
FREE
4pc Prybar Set
•
•
Model No. AK206
List Price
£26.95
Promotion Code: VST12.09
FREE
CVJ Removal Tool
3pc Ball Joint Removal Set
Ear-Type CVJ Boot/
Hose Clip Pliers
• Quickly removes the
CV joint from the
drive shaft without
damaging the joint,
and keeps hands
free for releasing
retaining circlip.
• Reduces risk of
damage to
transmission.
• Saves on labour
time and suitable
for most vehicles.
• Model No. VS710
• List Price £59.95
• Low profile set suitable
for most modern vehicles.
• Three sizes of jaw allow use on
most cars and light commercial
vehicles.
• Jaw Capacities: Small 23mm,
Medium 28mm, Large 34mm.
• Features heavy-duty forged steel body
and hardened screw with thrust ball.
• Model No. VS3800
• List Price £99.95
OFFER PRICE
£39.95 exc VAT
£47.94 inc VAT
Steering Rack
Knuckle Tools
o.
N
el
01
40
VS
d
Mo
l
de
FREE
2
00
S4
.V
No
FREE
Mo
5pc Prybar/Heelbar Set
CVJ Boot
Installation Tool
•
•
Model No. VS1633
List Price
£12.45
OFFER PRICE
£65.95 exc VAT
£79.14 inc VAT
CVJ Boot Band
Pliers
•
•
•
•
Model No.
VS705
List Price
£19.95
Model No. AK20641
List Price £29.95
• Suitable for the fast and easy removal/installation of the steering knuckle.
• Designed to fit over the steering shaft onto the steering rack.
• For the assembly of new stainless
steel bands on drive shafts
where a torque setting is
required.
• Model No. VS1640
• List Price £79.95
OFFER PRICE
£49.95 exc VAT
£59.94 inc VAT
Model No.
Diameter
List Price
Exc. VAT
Inc. VAT
VS4001
35.5 - 41mm
£109.95
£49.95
£59.94
VS4002
29 - 34mm
£109.95
£44.95
£53.94
CVJ Boot
Installation Tool
BMW Rear
Ball Joint Tool
Universal Stretch CVJ Boot
• Universal CV boot made from high quality
elastomer material suitable for use with
air operated boot installation tools.
• Supplied with fitting kit including
clips, grease sachet
and cutting guide.
• Suitable for most car
and car derived
van applications.
• Model No. CV96
• List Price £5.95ea
• Composite cone.
• Enables installation
of CVJ boot without
splitting drive train.
• Model No. VS705
• List Price £19.95
• Remove/install press-fit
rear suspension ball
joints in situ, on BMW 5
and 7 Series.
• Applications:
BMW 5 Series E39,
7 Series E38.
• Model No. VSE5509
• List Price £169.95
Bundle Deal
OFFER PRICE
£99.95 exc VAT
£119.94 inc VAT
2pc Lower Ball Joint Socket Set
• Set of two heat treated alloy steel sockets.
• Suitable for removal of OEM and aftermarket
lower ball joints.
• Applications:
Citroen; Xantia,
C5, C6,
Peugeot; 405, 406,
407, 605, 607.
• Supplied in
carry-case.
• Model No. SX0271
• List Price £29.95
OFFER PRICE
£19.95 exc VAT
£23.94 inc VAT
Promotion Code: VST12.09
Bundle Includes:
BUNDLE PRICE
1 x Model No. VS705
2 x Model No. CV96
Bundle Model No. VS705BD
Total Bundle List Price £31.85
£21.95 exc VAT
£26.34 inc VAT
Ear-Type Clip Pliers
Extra Heavy-Duty
• Steel jaws with PVC coated handles
for added comfort.
• Each handle features a 1/2"Sq
drive for use with a torque
wrench and breaker bar
where vehicle maker
demands specific
band
tensions.
• Model No.
VS1639
• List Price
£29.95
OFFER PRICE
£19.95 exc VAT
£23.94 inc VAT
Prices exclude VAT unless stated otherwise
25
Disc Brake Piston
Spreader
Pistol Grip
Pneumatic Pressure Bleeder Kit
• Designed to
fit front brake
callipers.
• Pistol grip design
provides a fast, no
nonsense approach
to pushing the piston
back.
• Model No. AK7113
• List Price £39.95
FREE
•
Model
No.
VS0209
List Price £29.95
•
FREE
18pc Brake Piston
Wind-Back Tool Kit
Gravity Brake
Bleeder
Kit
•
Model
No.
VS0209
List Price £29.95
•
• Suitable for push-back
and wind-back brake pistons.
• Includes left and right-handed
thrust bolt assemblies.
• Applications: Alfa Romeo, Audi,
BMW, Citroen, Fiat, Ford, Honda,
Jaguar, Mazda, Mercedes, Mitsubishi,
Nissan, Peugeot, Renault, Rover, Saab,
Seat, Skoda, Subaru, Toyota, Vauxhall/Opel,
VW, Volvo.
• Model No. VS0282
• List Price £129.95
OFFER PRICE
£54.95 exc VAT
£65.94 inc VAT
FREE
HGV Air Dryer Cartridge Remover
NEW
Mechanic’s Mat Set
EVA 22mm
•
•
•
•
•
•
Model No. VS857
List Price £34.95
Spring loaded air dryer filter wrench.
Essential tool for removing commercial air brake filters.
Model No. VS935
List Price £139.95
Brake & Clutch Bleeding System
• One-man brake and clutch bleeding
the professional way.
• Requires no external power source
- simply fill and pump.
• Holds 2.5ltr of hydraulic fluid - flush
the entire system with one fill
without the risk of running the
reservoir dry.
• Pressure range makes unit suitable
for use with ABS systems.
• Fitted with Ø42mm cap and
suitable for most European models.
• Model No. VS820
• List Price £99.95
OFFER PRICE
£69.95 exc VAT
£83.94 inc VAT
26
Model No. VS0282
List Price £129.95
Gravity Brake
Bleeder
Kit
£24.95 exc VAT
£29.94 inc VAT
£99.95 exc VAT
£119.94 inc VAT
18pc Brake Piston
Wind-Back Tool Kit
•
•
OFFER PRICE
OFFER PRICE
FREE
• One-man pressure brake and clutch bleeding
system suitable for the professional workshop.
• Low pressure tank (20-40psi) can be pre-charged
with compressed air - making the unit fully portable.
FREE
Disc Brake Piston
Spreader - Pistol Grip
•
•
Model No. AK7113
List Price £39.95
• Suitable for use on ABS systems.
• Features a long delivery hose for operation with a low
level ramp and long reach handle for easy mobility.
• Model No. VS0204
• List Price £399.95
OFFER PRICE
£274.95 exc VAT
£329.94inc VAT
2pc Calliper
Support Hooks
• Used to hold the brake
calliper away from the hub
when replacing brake pads.
• Simply hang the calliper hook onto a
suitable suspension component to hold the
calliper out of the way and also stop
the weight of the calliper damaging
the brake hose.
• Model No. VS0354
• List Price £6.45
OFFER PRICE
£3.95
£4.74
exc VAT
inc VAT
11pc Brake Service Kit
• Set contains the majority of
tools required to carry
out servicing/repair
work on disc
and drum
brakes.
• This handy set
is supplied in a
carry-case to
keep these
commonly used
tools together and
is ideal for the
busy workshop.
• Model No. VS0353
• List Price £109.95
OFFER PRICE
£59.95 exc VAT
£71.94 inc VAT
Automatic Brake &
Clutch Bleeder
• Fast, easy and effective
bleeding of brakes and
clutch using air from tyre.
• Innovative design
incorporates valve for
control of air pressure,
extra-long air hose for
use with larger vehicles
and magnetic reservoir
base to prevent
accidental spillage.
• Supplied with range
of common adaptors.
• Model No. VS0205
• List Price £29.95
FREE
Brake Piston Cube
3/8"Sq Drive
•
•
Model No.
VS039
List Price
£9.95
OFFER PRICE
£19.95 exc VAT
£23.94 inc VAT
Prices exclude VAT unless stated otherwise
Promotion Code: VST12.09
Electronic Parking Brake
Service Tool
Brake Flaring Tool
Turret Type
• Suitable for safe and professional
replacement of brake pads on
vehicles fitted with an electronic
parking brake (EPB).
• Deactivates/activates SBC
(Sensotronic Brake Control).
• Applications: Audi; A6, A8
(02on), Mercedes; E Class
(02-07) (W211), SL (02on)
(R230), CLS (01-02) (C219),
VW; Passat (05on).
• Model No. VS8622
• List Price £199.95
FREE
8pc Brake Piston
Wind-Back Tool Kit
•
•
Model No. VS028
List Price £71.95
OFFER PRICE
• Cam-action body mounts in bench vice for ease of use.
• Supplied with 4.75mm, 3/16", 1/4", 5/16" and 3/8"
dies and 4.75mm, 3/16", 1/4", 5/16" clamp blocks
for forming most popular flares.
• Optional 3/8" clamp block available.
• Model No. PFT07
• List Price £279.95
•
£179.95 exc VAT
£215.94 inc VAT
FREE
Brake Pipe Bender
•
OFFER PRICE
Brake & Fuel Pipe
Inspection Tool
Model No.
VS5055
List Price
£24.95
•
•
Model No.
VS0210
List Price
£16.95
•
Model No.
VS0350
List Price
£24.95
• Compact design for bending
automotive brake pipes without
crushing the pipe walls.
• Rigid construction makes it
suitable for steel pipes.
• Will bend Ø3mm (1/8"),
Ø4.75mm (3/16") and
Ø6mm (1/4") pipe up to 90°.
FREE
3pc Miniature
Brush Set
OFFER PRICE
£14.95
£17.94
inc VAT
•
• Model No. VS5055
• List Price £24.95
•
Model
No.
AK9791
List
Price
£3.95
FREE
Brake Pipe Cutter
• Patented design ensures
that the spring mechanism
maintains the correct
cutting pressure on
the pipe at all times.
• Features a smooth
screw action and
nickel plated
blade for
increased cutting
performance.
• Model No. VS0350
• List Price £24.95
Brake & Fuel Pipe Inspection Tool
• Specially designed for the removal of
corrosion from brake and fuel pipes for
fast and thorough inspection.
• Applications: 3.5mm (Citroen), 4, 4.75mm;
3/16" Pipes.
• Ideal for use during MOT inspections.
• Model No. VS0210
• List Price £16.95
OFFER PRICE
£10.95 exc VAT
£13.14 inc VAT
Promotion Code: VST12.09
Brake Calliper Thread
Repair Kit M12 x 1.5mm
Brake Pipe Cutter
•
Brake Pipe Bender
exc VAT
£139.95exc VAT
£167.94 inc VAT
• Quick and
effective method
of replacing brake
calliper threads using
M12 x 1.5mm inserts.
• Kit includes M12 x 1.5mm
tap, step drill, insert locator,
two washers with centre roller
bearing and ten replacement
inserts in storage case.
• Model No. VS0463
• List Price £139.95
FREE
Disc Brake Piston
Spreader Tool
•
•
Model No. AK711
List Price £32.95
OFFER PRICE
£89.95 exc VAT
£107.94 inc VAT
12pc Fuel Line Clamp & Stopper Kit
7mm Angled Head
Long Reach Hex
Wrench
•
•
Model No. AK6572
List Price
£4.95
OFFER PRICE
£14.95
£17.94
exc VAT
inc VAT
• A comprehensive kit
designed to stop the
flow of fuel from fuel
lines after disconnection.
• Compatible with brake,
transmission, fuel lines
and other applications.
• Model No. VS0558
• List Price £74.95
OFFER PRICE
£49.95 exc VAT
£59.94 inc VAT
4pc Hose Pinch Tool Set
• Light and compact steel
alloy construction allows
easy use where space
is limited.
• Rounded jaw edges
prevents damage to
internal hose reinforcements.
• Suitable for use on fuel,
vacuum and brake hoses.
• Model No. VS0301
• List Price £19.95
OFFER PRICE
£12.95
£15.54
Prices exclude VAT unless stated otherwise
exc VAT
inc VAT
27
FREE
Tyre Changer Pneumatic/
Manual Operation
• Centre cone clamp makes this
tyre changer ideal for use with
most automotive/light
commercial open centre wheels.
• Heavy-duty bead breaker
(operating force up to 1250kg)
- is able to handle latest safety
wheels.
• Min./Max. Wheel Clamping Size:
203/460mm (8"/18").
• To prevent damage to the rims
of the alloy wheel, it is essential
to use a TC963 Tyre Bar.
• Model No. TC962
• List Price £729.95
4pc 1/2"Sq Drive
Alloy Wheel
Impact Socket Set
•
•
Model No. SX030
List Price
£49.95
OFFER PRICE
• Dumps air into tyre
void forcing bead
to seat against rim
for inflation.
• Fully certified tank
with gauge and
safety valve prevents
over pressurising.
• Suitable for use on
cars, commercials,
agricultural and
ATV tyres.
• Model No. TC900
• List Price £299.95
OFFER PRICE
£499.95exc VAT
£599.94 inc VAT
£199.95exc VAT
£239.94inc VAT
3pc 1/2"Sq Drive Alloy Wheel
Deep Impact Socket Set
14pc Wheel
Maintenance Kit
• Features nylon sleeve
and insert to prevent
damage to alloy
wheels.
• Colour coded sockets
for easy size selection.
• Comprises deep 17,
19 and 21mm 1/2"Sq
drive sockets, plus
spare nylon sleeves.
• Model No. SX031D
• List Price £69.95
FREE
2pc 1/2"Sq Drive
Locking Wheel Nut
Removal Set
OFFER PRICE
£44.95 exc VAT
£53.94 inc VAT
Bead Seating Tool
•
•
Model No.
SX200
List
Price
£17.95
7pc 1/2"Sq Drive Locking
Wheel Nut Removal Set
• Removes surface
dirt and corrosion.
• Ideal for preparing
wheels, hubs and brake
discs or drums for
re-assembly.
• Suitable for use with power
drill or air impact wrench.
• Supplied with 1/2"Sq drive adaptor.
• Model No. SX036
• List Price £52.95
OFFER PRICE
£34.95 exc VAT
£41.94 inc VAT
Torque Sticks
1/2"Sq Drive
3
24
S2
el
od
N
M
• May also be used on fixings too damaged or
corroded for standard sockets.
• Suitable for use with impact wrenches.
• Contents: 17, 18.5, 20, 21.5, 23, 24.5, 26mm.
• Model No. SX202
• List Price £52.95
£34.95 exc VAT
£41.94 inc VAT
• Removes the plastic wheel nut caps fitted to Audi,
Seat, Skoda, Vauxhall/Opel and VW vehicles.
• Eliminates the need to lever off caps with a
screwdriver, which may damage the alloy wheel.
• Up to six caps may be stored in the handle,
ready for refitting.
OFFER PRICE
28
exc VAT
inc VAT
el
od
N
M
5
el
od
S2
V
o.
N
M
6
el
od
S2
V
o.
N
M
7
24
24
24
S2
V
o.
el
od
V
o.
N
M
OFFER PRICE
Wheel Nut Cap Remover
£17.95
£21.54
4
24
S2
V
o.
• Model No. VS930
• List Price £29.95
• Chrome Molybdenum steel torque stick designed for use with air and electric impact wrenches.
• Prevents over-torque of wheel nuts.
• Features a twist distortion marking for checking serviceability of tool.
Model No.
Colour
Torque
Rating
List Price
Exc. VAT
Inc. VAT
VS2243
Green
65lb.ft (90Nm)
£19.95
£12.95
£15.54
VS2244
Black
75lb.ft (100Nm)
£19.95
£12.95
£15.54
VS2245
Gold
80lb.ft (110Nm)
£19.95
£12.95
£15.54
VS2246
Red
90lb.ft (120Nm)
£19.95
£12.95
£15.54
VS2247
Blue
100lb.ft (135Nm)
£19.95
£12.95
£15.54
Prices exclude VAT unless stated otherwise
Promotion Code: VST12.09
Tyre Valve Removal/
Installation Tool
NEW
Jumbo
Tyre Inflators
Push-On
Connector
Model No.
SA9313
Clip-On
Connector
Model No.
SA9303
FREE
Tyre Valve Core Tool
•
Remove tyre valve from wheel.
Push valve through the wheel.
• Remove and install leaking tyre valves without
having to remove the tyre.
• Works on steel wheels and especially good for
valves on motorcycle or agricultural wheels.
• Time saving tool.
• Contents: Cone, Push/Pull Driver, Valve Hook Tool.
• Not suitable for high pressure valves.
• Model No. TSTVRK
• List Price £19.95
OFFER PRICE
£12.95
£15.54
12V Heavy-Duty Compressor
• Suitable for inflating tyres on
cars, vans and 4x4s.
• Powered by reliable, heavyduty motor producing 45ft3
air per hour.
• Integral gauge reads up to
20bar/300psi.
• Maximum Working Pressure:
200psi.
• Accessory kit containing,
Presta type adaptor, ball
spike and two inflatables
adaptors included in storage
compartment on base.
• Model No. MAC2300
• List Price £74.95
Pull valve to seat in wheel rim.
exc VAT
inc VAT
Model No.
TST/VCT
List Price
£2.95
•
• Composite body and dial type jumbo
gauge with rubber protector.
• Calibrated in bar and psi.
• Fitted with 400mm rubber hose.
Model No.
Range
Air Inlet
Size
List
Price
Exc. VAT
Inc. VAT
SA9303
0-6.9bar(0-100psi)
1/4"BSP
£31.95
£19.95
£23.94
SA9313
0-11bar(0-160psi)
1/4"BSP
£34.95
£21.95
£26.34
Tyre Valve Installer
of
• Simplifies installation of tyre valves in tubeless wheels.
• Pulls tyre valve assembly through rim.
• Shank is notched to accommodate
various rim styles.
• Strong 270mm long handle
with corrosion resistant plating.
• Model No. TST/TVI
• List Price £8.45
OFFER PRICE
£4.95
£5.94
exc VAT
inc VAT
Single Barrel Foot Pump
OFFER PRICE
£49.95 exc VAT
£59.94 inc VAT
TPMS Valve Tool
• Specialist tool designed to remove 11mm and
12mm TPMS sensor nuts and reseating the
bevelled and non-bevelled sealing grommets.
• Model No. TSTPMS
• List Price £5.45
• 610mm Flexible hose
with locking connector.
• 0-100psi.
• Supplied with accessory
for inflating items such
as small inflatable boats,
air beds and balls etc.
• Model No. FP1
• List Price £12.95
OFFER PRICE
£9.45
£11.34
exc VAT
inc VAT
OFFER PRICE
£3.55
£4.26
exc VAT
inc VAT
Dial Type Tyre Pressure Gauge
TUV/GS Approved
• Dial type pressure gauge with metal
body and offset valve connector.
• Accurate to ±1.5psi.
• Range: 0-3bar/0-40psi.
• Model No. TST/PG97
• List Price £8.95
OFFER PRICE
£5.95
£7.14
exc VAT
inc VAT
Promotion Code: VST12.09
Digital Tyre Tread
Depth Gauge
• Tough Composite
sliding gauge.
• 10mm High figures
in LCD display.
• Range: 0-25mm/0-1".
• Zero setting control
allows for comparative
measurement.
• Model No. VS0564
• List Price £17.95
OFFER PRICE
£11.95
£14.34
Prices exclude VAT unless stated otherwise
FREE
Tyre Pressure
Gauge
exc VAT
inc VAT
•
•
Model No. TSTPG1
List Price £3.75
29
Twin Leg Pullers
Bar Type
5tonne Triple Leg
Hydraulic Puller
Model No. AK46250
• Heavy-duty twin leg bar type puller.
• Easy removal of pulleys, flywheels,
bearings and gears.
• Drop-forged Chrome Vanadium
steel.
• Heat treated and chrome plated.
• Thrust bearing prevents wear and
damage to shaft.
Model No.
Size/Spread x Reach
List Price
Exc. VAT
Inc. VAT
AK46080
80 x 100mm
£13.45
£7.95
£9.54
AK46120
120 x 100mm
£18.95
AK46150
£10.95
£13.14
150 x 150mm
£33.95
£18.95
£22.74
AK46200
200 x 150mm
£41.95
£23.95
£28.74
AK46250
250 x 200mm
£62.95
£35.95
£43.14
• Heavy-duty
triple leg
5tonne
hydraulic
puller.
• Suitable for
pulling hubs,
flanges, gears
and bearings.
• Supplied with
three 2-position
puller legs and
carry-case.
• Model No. HP5
• List Price £114.95
FREE
Twin Leg Puller Bar Type
120 x 100mm
OFFER PRICE
£79.95 exc VAT
£95.94 inc VAT
•
•
FREE
Hydraulic Hub Puller Set
19pc Hydraulic Puller Set
• Forged steel 2-way yoke allows
twin or triple leg pulls.
• 10tonne Hydraulic
power unit with
tommy bar.
• Supplied with
3 x 3 position
puller arms and
3 sets of extension
plates.
• Maximum reach:
250mm.
• Model No. PS981
• List Price £164.95
FREE
£99.95 exc VAT
£119.94 inc VAT
•
•
• Drop-forged, high carbon
steel reversible legs and
body.
• Heat treated and zinc
plated to resist corrosion.
• Swivel thrust plates on
larger sizes prevent
damage to shaft ends.
• Sizes: 75, 100, 150, 200mm.
• Model No. VS79
• List Price £60.95
5pc Scraper
& Hook
Set
OFFER PRICE
•
•
Model
No. AK520
List Price £19.95
FREE
5pc Scraper
& Hook
Set
•
•
30
Model
No. PP1
List Price
£39.95
£84.95 exc VAT
£101.94 inc VAT
FREE
• Multi-purpose puller
set for extracting
flywheels and pulleys.
• Minimum/Maximum
Spread: 40/93mm.
• Model No. PS979
• List Price £45.95
•
4pc Triple Leg
Gear Puller Set
• Mechanical puller set
with Ø30-50mm
and Ø50-75mm
separators and
single yoke with
180mm thrust bolt.
• Model No. PS984
• List Price £109.95
49pc Harmonic
Balancer
Puller
Set
•
OFFER PRICE
Model
No.
AK5209
List Price £31.95
12pc Mechanical Bearing
Separator Set
£69.95 exc VAT
£83.94 inc VAT
6-24V Auto Probe
with 4.5mtr Cable
• Chromed, heat
treated S45C
steel puller
yoke with
hydraulic ram.
• Suitable for four
and five stud hubs.
• Hydraulic ram
provides additional
power to extract the
most stubborn hubs.
• Model No. PS993
• List Price £119.95
9pc Scraper
& Hook
Set
OFFER PRICE
Model No.
AK46120
List Price
£18.95
Model
No. AK520
List Price £19.95
FREE
OFFER PRICE
£39.95 exc VAT
£47.94 inc VAT
6pc Pick & Hook
Set Extra-Long
•
•
Model No. AK5215
List Price £19.95
1.2mtr Telescopic Bonnet/Tailgate Support
• Three tier telescopic aluminium tailgate/bonnet
support with tough rubber pads at each end.
• Lock in any position with a simple twist.
• Also used for holding open doors,
depressing clutch, brake
or accelerator pedals.
• Model No. VS0140
• List Price £12.95
OFFER PRICE
£29.95 exc VAT
£35.94 inc VAT
Prices exclude VAT unless stated otherwise
OFFER PRICE
£8.45
£10.14
exc VAT
inc VAT
Promotion Code: VST12.09
Anemometer
• Wind
speed
measuring
device
featuring
live/max/
average/
wind chill and
Beaufort scale.
• Also reads temperature
which can be measured
in either °C or °F.
• Readings are displayed on
a 24mm high back-lit LCD screen.
• Features a battery indicator and
auto/manual power off.
• Requires CR2032 3V battery
(supplied).
• Model No. TA070
• List Price £34.95
FREE
NEW
Ultrasonic Leak Detector
Mini Digital
Thermometer
• Model No. VS906
• List Price £17.95
OFFER PRICE
£22.95 exc VAT
£27.54 inc VAT
• Quick and simple
location of air, water,
dust leaks.
• Place the transmitter in the vehicle
and close the doors and windows.
• Trace the detector around outside of the screen,
windows and door seals to locate the leak.
• Includes adjustable headphone for detector.
• Transmitter and detector powered by 9V Lithium
batteries.
• Supplied in foam lined carry-case.
• Model No. PP4
• List Price £79.95
Sound Level Meter
1ltr Chemical Sprayer
• High quality meter suitable for
measurement of environmental
and mechanical noise.
• Conforms to IEC61672-1 class 2
for sound meters.
• Features min./max. measurements,
over and under range, A and C
weighting, fast and slow response,
data hold, record, digital read-out
and bar graph with backlight.
• Powered by 9V battery (supplied).
• Model No. TA060
• List Price £139.95
• Ideal for use with some brake
cleaners, detergents, traffic film
remover, penetrating oils and
weed killer.
• Adjustable nozzle enables easy
and direct application of liquid
exactly where it is required.
• Robust composite construction
with 1ltr capacity container.
• A compatibility document is
available.
• Model No. TP01
• List Price £22.95
FREE
OFFER PRICE
£49.95 exc VAT
£59.94 inc VAT
Mini Digital
Thermometer
OFFER PRICE
£99.95 exc VAT
£119.94 inc VAT
•
•
Model No. VS906
List Price £17.95
OFFER PRICE
£13.95 exc VAT
£16.78 inc VAT
On-Vehicle Brake Disc Lathe
• Time and money saver that allows the brake disc to be refaced
whilst still on the vehicle and mounts directly to the mounting
holes of the brake calliper.
• Eliminates disc run-out and compensates for small inaccuracies
in the hubs.
• Features a flexible mounting system with a selection of adaptors
for various vehicles.
• Automatic setting with cut-out allows the operator to leave the
unit unattended.
• See Video tab on our website for full demonstration video
www.sealey.co.uk.
• Model No. VS0299
• List Price £6495.95
Workshop Headlamp
Beam Setter
• Suitable for pre-MOT inspection
in garages and bodyshops.
• Utilises same optical box and
aiming screen as fitted to our
MOT approved headlamp
beam setter.
• Fixed aiming screen. Internal
analogue LUX meter for
accurate light intensity
measurement.
• Suitable for all types of cars
and light commercial vehicles.
• Fitted with fixed column and
rubber wheels.
• Model No. HBS2001
• List Price £724.95
FREE
Replacement Cutting
Tips for Brake Disc
Lathe Pack of 10
OFFER PRICE
£3995.95 exc VAT
£4795.14 inc VAT
Promotion Code: VST12.09
•
•
Model No. VS0299R
List Price
£179.95
Prices exclude VAT unless stated otherwise
OFFER PRICE
£499.95 exc VAT
£599.94 inc VAT
31
Under-Vehicle Engine Support - Base Unit
• Supports/raises engine from underneath during maintenance operations
without use of a trolley jack or conventional over-engine support beam.
• Allows unimpeded access to the engine from above and also permits
safe movementof the vehicle whilst the engine is raised.
• Vehicle-specific adaptor sleeve mounts onto the vehicle structure and
takes the support beam.
• Engine is raised by a screw adjusted pad.
• Vital for rapid and safe timing belt changes, engine
mount replacement and transmission removal.
• No risk of scratching customer's paintwork around
inner wings.
OFFER PRICE
• No need for chains or lifting straps.
exc VAT
• Sleeve system allows fitting to a wide range of vehicles.
• Model No. ES200
inc VAT
• List Price £219.95
£89.95
£107.94
Model
No.
Applications
Picture
Model
No.
Applications
Picture
Model
No.
Applications
ES200-01
Ford Galaxy,
Seat Alhambra,
VW Sharan
ES200-11
Citroen C4
ES200-20
GM Astra H,
Zafira B Petrol
(2005 on)
ES200-02
Audi A3, Seat Leon,
Skoda Octavia,
VW Golf, Beetle
ES200-12
Citroen C5
ES200-21
GM Vectra C
Deisel,
Saab 9-3 Diesel
(2005 on)
ES200-03
Ford Focus
ES200-13
Peugeot 407
ES200-22
Citroen Jumper,
Fiat Ducato,
Peugeot Boxer
ES200-04
Peugeot 206, 307
ES200-14
Citroen Jumpy,
Peugeot
Expert/806
ES200-23
GM Vectra Petrol
ES200-05
Citroen Berlingo,
Peugeot 406,
Partner
ES200-15
Citroen Picasso/
Xantia/Xsara/ZX
ES200-25
Fiat Stilo 1.6 Petrol
ES200-06
Ford C-Max
ES200-16
Citroen C8,
Peugeot 807
ES200-26
Alfa Romeo 159
Diesel (2006 on)
ES200-07
Ford Fusion, Fiesta
ES200-17
Peugeot 607
ES200-27
GM Zafira A/Astra
1.6 Petrol
ES200-08
Audi A3,
Seat Altea/Toledo,
Skoda Octavia 2004,
VW Golf 5
ES200-18
Skoda Fabia,
Seat Ibiza (2002 on),
VW Polo
ES200-28
Fiat Doblo
ES200-10
Skoda Roomster,
VW Lupo
ES200-19
Ford Fiesta Diesel
(2005 on)
ES200-29
VW Transporter
ALL ADAPTORS £54.95 EACH
LIST PRICE £143.95 EACH
32
Prices exclude VAT unless stated otherwise
Picture
OFFER PRICE
£54.95 exc VAT
£65.94 inc VAT
Promotion Code: VST12.09
40kg Vacuum Suction Cup
10pc Scraper Set
• Nylon and glass fibre manufacture
provides strength and durability.
• Ideal for removing gasket residue
and other stubborn materials.
• Model No. RT10K
• List Price £33.95
NEW
• Rubber suction device with red
line indicator which warns of
any vacuum loss.
• Easy attachment on smooth,
non-porous flat surfaces such
as glass, sheet metal and tiles.
• Model No. AK98941
• List Price £89.95
NEW
OFFER PRICE
OFFER PRICE
£59.95 exc VAT
£71.94 inc VAT
£20.95 exc VAT
£25.14 inc VAT
40kg Vacuum Suction Cup - Curved Surfaces
•
•
Model No. RT011
List Price £5.95
• Tools specially designed
to remove small
items of trim.
• Manufactured from
nylon to minimise
damage.
• Compact design
allows use even
where space is
limited or where trim
is most fragile.
• Model No. RT7KIT
• List Price £25.95
• Profiled rubber suction cup suitable
for attachment to curved surfaces
such as windscreens.
• Red line indicator warns of any
vacuum loss.
• Easy attachment on smooth,
non-porous flat surfaces such
as glass, sheet metal and tiles.
• Model No. AK98942
• List Price £109.95
OFFER PRICE
OFFER PRICE
£79.95 exc VAT
£95.94 inc VAT
4pc Micro Welding Clamp Set
ARRIVING
OCTOBER
7pc Mini Automotive Trim
& Upholstery Tool Set
NEW
• Small and compact with exceptional
clamping force.
• Ideal for automotive applications
when positioning body panels prior
to welding.
• Micro clamp enables areas to be
secured where other tools struggle
to fit, such as door columns and
window edges.
• Model No. AK6804
• List Price £34.95
FREE
2pc Mini Trim Clip
Removal Pliers
£14.95
£17.94
NEW
• Glass reinforced nylon trim clip
removal pliers with spring-loaded
handles.
• Length: 100mm.
• Model No. RT011
• List Price £5.95
OFFER PRICE
FREE
£22.45 exc VAT
£26.94 inc VAT
inc VAT
2pc Mini Trim Clip
Removal Pliers
NEW
OFFER PRICE
exc VAT
2pc Mini Trim Clip
Removal Pliers
•
•
Model No. RT011
List Price £5.95
Adjustable Double Head
Suction Gripper
£3.95
£4.74
exc VAT
inc VAT
5pc Auto Electrical Installation Kit
• Slim profile helps to locate and seat
wiring loom in awkward places and
to separate individual wires ready
for inspection/installation,
so minimizing damage.
• Model No. RT5KIT
• List Price £24.95
OFFER PRICE
£14.95
£17.94
NEW
NEW
FREE
2pc Mini Trim Clip
Removal Pliers
exc VAT
inc VAT
•
•
Model No. RT011
List Price £5.95
Single Head Suction Gripper
• Designed for handling materials such as glass, tiles,
plastic, sheet metal and other non-porous materials.
• Two Ø115mm rubber suction grips prevent damage to
surface.
• Adjustable handle allows use on curved surfaces.
• Holds up to 60kg in the horizontal position.
• Model No. AK8929
• List Price £37.45
Promotion Code: VST12.09
• Ø60mm Rubber suction grip prevents damage
to surface.
• Designed for handling glass, tiles, plastic and
other non-porous material.
• Holds up to 10kg in the horizontal position.
• Model No. AK9990
• List Price £9.95
OFFER PRICE
£24.95 exc VAT
£29.94 inc VAT
OFFER PRICE
£5.95
£7.14
Prices exclude VAT unless stated otherwise
exc VAT
inc VAT
33
Professional
Dent Pullers
33pc Paintless
Dent Repair Kit
NEW
FREE
• Specialist device for
pulling dents from
panels and bodywork.
• Contoured aluminium
handle and suction
release trigger give
the technician close
control.
3pc Windscreen
Handling Kit
•
•
Model No. WK1
List Price
£74.95
• Heavyweight, heat treated, high quality steel components are carefully
shaped and finished to allow the technician (with practice) to coax out
all manner of dents and creases from behind the body panel, removing
the need to respray/refinish the painted surface.
• The results achieved with this kit will depend on the skill of the operator.
• Model No. RE102
• List Price £399.95
Air Suction
Dent Puller
• Air activated
suction pad keeps
firm hold of panel.
• Slide hammer used to ease
out dents and depressions
without damage to the
paint surface.
• Ideal for initial panel
reshaping.
• Supplied with large and
small suction pads.
• Model No. RE101
• List Price £169.95
Model No. Diameter
OFFER PRICE
£299.95exc VAT
£359.94 inc VAT
Model No. AK100
Max. Pull
Capacity
List Price
Exc. VAT
Inc. VAT
AK100
Ø75mm
10kg
£27.95
£17.95
£21.54
AK101
Ø100mm
15kg
£28.95
£18.95
£22.74
AK102
Ø125mm
20kg
£29.95
£19.95
£23.94
7pc Airbag Removal Tool Set
FREE
Ø60mm
Air Suction Pad
•
Model No.
RE101.60
List Price
£14.95
•
OFFER PRICE
• Designed for the safe removal
of steering wheel airbags.
• Suitable for use on
Audi, BMW, Mercedes,
Seat, Skoda and
VW vehicles.
• Model No. VS9000
• List Price £57.95
OFFER PRICE
£99.95 exc VAT
£119.94 inc VAT
£34.95 exc VAT
£41.94 inc VAT
Door Hinge & Handle
Removal Kit
6pc Pick & Hook Set Extra-Long
• TRX-Star* tools for the
easy removal of door hinges
and handles.
• For Audi, Mercedes, Porsche
and VW models.
• Consists of two TRX-Star* long-reach
drivers, 8mm hex drive reversible ratchet
wrench and four TRX-Star* bits.
• Model No. VS805
• List Price £40.95
FREE
• Six long reach picks with black
finished steel shafts.
• Contents: Straight, Right Angle,
Half-Round, Swan Neck,
45°/ 90° Tip, 40°/45° Tip.
• Suitable for pin/clip
picking and the
removal of O-rings
and seals.
• Model No. AK5215
• List Price £19.95
Trim Stick
OFFER PRICE
£24.95 exc VAT
£29.94 inc VAT
•
•
Model No. RTTS
List Price £4.95
9pc Radio Release Tool Set
• Stainless steel radio removal tools.
• For Audi, BMW, Ford, Mercedes
Benz and VW.
• Supplied in labelled storage
pouch.
• Model No. VS804
• List Price £21.95
OFFER PRICE
£11.95
£14.34
exc VAT
inc VAT
36 Function
Radio Release
Key Set
• Thirty-six tools in one.
• Updated set of tools
for safe, fast, authorised
removal of fitted radios.
• Composite handle allows
firm and comfortable grip.
• Model No. VS8048
• List Price £34.95
FREE
6-24V Circuit Tester
OFFER PRICE
£12.95
£15.54
34
exc VAT
inc VAT
OFFER PRICE
£25.95
£31.14 inc VAT
exc VAT
Prices exclude VAT unless stated otherwise
•
•
Model No. AK4008
List Price
£7.75
Promotion Code: VST12.09
HVLP Gravity Feed Spray Gun
2.0mm Set-Up
HVLP Gravity Feed Touch-Up Spray
Gun 0.8mm Set-Up
• Standard large set-up and economy price make
this spray gun ideal for applying base coats.
• Round/flat fan control allows spray pattern to be
adjusted for any job.
• Anodized spray gun body resists corrosion
and makes for easier cleaning.
• Aluminium air cap with stainless steel
needle and nozzle make this HVLP
gun suitable for water based paint.
• Supplied with 2.0mm set-up suitable
for primer. 1.4 and 1.7mm
set-ups available separately.
• Model No. HVLP742
• List Price £72.95
• Professional gravity feed spray gun with 0.8mm
set-up, ideal for small panels.
• HVLP Design gives a high transfer efficiency
of paint saving on costs.
• Brass air cap with stainless steel needle
and nozzle suitable for water based paints.
• Features air and paint flow controls
for fine adjustment of spray pattern.
• Fully polished body resists corrosion
and makes for easy cleaning.
• Alternative set-up available separately.
• 1.0mm Set-up available.
• Model No. HVLP736
• List Price £69.95
FREE
OFFER PRICE
£49.95 exc VAT
£59.94 inc VAT
FREE
20pc Spray Gun
Cleaning
Set
OFFER PRICE
£46.95 exc VAT
£56.34 inc VAT
• Model
No. BSGC2
• List Price
£10.45
Gravity Feed Spray Gun
2.0mm Set-Up
• Superbly balanced spray gun
ideal for applying base coats.
• Features adjustable paint flow,
fan width and air regulator controls.
• Supplied with composite
gravity feed pot.
• Suitable for use with
water based paints.
• Alternative set-ups
available separately.
• Model No. SSG5
• List Price £45.95
OFFER PRICE
£29.95 exc VAT
£35.94 inc VAT
• Model
No. BSGC2
• List Price
£10.45
General Purpose
Suction Feed Spray
Gun 1.5mm Set-Up
• Ideal for applying base coats.
• Features adjustable paint flow
and fan width controls.
• Supplied with aluminium screw
type suction feed pot.
• Suitable for use with water
based paints.
• Alternative set-ups available
separately.
• Model No. SSG2
• List Price £34.95
FREE
5pc Mini Brush Spray
Gun Cleaning Set
OFFER PRICE
£24.95 exc VAT
£29.94 inc VAT
• Model No.
BSGC4
• List Price
£5.45
Wheel Skate Hydraulic
680kg Capacity
• Steel tube chassis with four
Ø100mm nylon castors.
• Aluminium rollers cradle
vehicle’s tyre
and are
capable of
handling up
to 240mm
profile.
• Suitable for
bodyshops, garages,
showrooms or anywhere
a disabled vehicle needs
moving on an even surface.
• Note: Sold as singles, but
must be used in pairs.
• Model No. WS680
• List Price £209.95
20pc Spray Gun
Cleaning
Set
FREE
5pc Mini Brush Spray Gun
Cleaning Set
• Model
No. BSGC4
• List Price
£5.45
Dust-Free Air Operated
Random Orbital
Sander
OFFER PRICE
£149.95 exc VAT
£179.94 inc VAT
10pc Heavy-Duty
Slide Hammer Kit
• Lightweight, balanced
aluminium body with
smooth double bearing
counter balance
assembly for
fatigue free
operation.
• Fitted with
airflow control
valve, safety
knuckle guard
and housing insulation
to prevent hand chill.
• Pad not included.
• Model No. SA7/SAS
• List Price £99.95
FREE
150 x 230mm Hand
Pads Fine Pack of 10
• Model No.
HP1523F
• List Price
£9.95
OFFER PRICE
£69.95 exc VAT
£83.94 inc VAT
5pc Air Accessory Kit
• Heavy-duty slide hammer with
4.4kg sliding weight.
• For use on body panels
and vehicle chassis.
• Supplied with various
attachments.
• Model No. DP90
• List Price
£119.95
OFFER PRICE
£84.95 exc VAT
£101.94 inc VAT
Promotion Code: VST12.09
• Contents:
Suction Feed Spray Gun, Blowgun, Tyre Inflator,
Paraffin Gun, Coiled Air Hose with couplings.
• Model No. SA33/S
• List Price £49.95
Prices exclude VAT unless stated otherwise
OFFER PRICE
£32.95 exc VAT
£39.54 inc VAT
35
STOCK CLEARANCE
THESE ITEMS WILL SELL OUT
Throttle
Potentiometer
Tester
• Simple to use digital
meter indicates
throttle position sensor
output voltage.
• Connect to battery
terminals and
sensor signal wire.
• Model No. VS215
• List Price £97.45
OFFER PRICE
£54.95 exc VAT
£65.94 inc VAT
3pc 3/8"Sq Drive
Spark & Glow
Plug Torque
Limiter Set
3pc 3/8"Sq Drive
Torque Control
Spark Plug
Socket Set
• Supplied with 3
common torque ratings,
10, 15 and 25Nm.
• Developed in
conjunction with
leading plug maker.
• Model No. SX0371
• List Price £89.95
• Chrome Vanadium
steel, WallDrive®, 12-point
sockets, with plug
retaining insert.
• Sizes: 14, 16, 21mm.
• Torque Limits: 19, 20,
25Nm.
• Model No. SX037
• List Price £97.45
£36.95 exc VAT
£44.34 inc VAT
13pc Fuel Pump Timing Kit
Bosch, Lucas/CAV
2pc Coil Spring Compressor
with Safety Jaws
• Kit includes Bosch adaptor for pumps fitted
with M10 service ports commonly
found on VW/Audi, Volvo,
Renault and Ford Transit.
• Model No. VS1131
• List Price £229.95
• Features spring loaded safety jaws for easy location
of the jaws on assembly.
• Prevents accidental release of spring under load.
• Use with 24mm hex socket or spanner.
• Model No. AK3844
• List Price £104.95
OFFER PRICE
• Suitable for Ford 1.6 and 1.8 diesel
engines as fitted to Fiesta, Escort,
Orion, P100, Sierra, Mondeo
Transit 2.5DI (85on)
and Galaxy 1.9TD.
OFFER PRICE
£19.95
£23.94 inc VAT
• Model No.
VSE101
• List Price £36.95
4pc 1/2"Sq Drive Torque
Control Impact Socket Set
4pc T-Handle Spark
Plug Socket Set
• Universal
joint, spark
plug sockets
with built-in
extension
bar.
• Socket Sizes:
14, 16, 18, 21mm.
• Model No. SX0405
• List Price £78.95
• Chrome Molybdenum steel,
WallDrive®, impact sockets.
• Torque Limit:
60lb.ft/80Nm.
• Sizes: 17, 19, 21, 22mm.
• Model No. SX035
• List Price £134.95
OFFER PRICE
OFFER PRICE
£39.95 exc VAT
£47.94 inc VAT
£39.95 exc VAT
£47.94 inc VAT
Petrol Injection Pressure Test
Kit Mechanical Systems
Petrol Engine Setting/Locking Kit - Citroen,
Peugeot, Renault 3.0 V6 - Belt Drive
• Used in conjunction with
Model No. VS2110 Test Kit.
• Kit consists of three in-line
tees, ten male and female
thread adaptors and spare
O-rings and valve cores.
• Suitable for setting and locking Renault
3.0 V6 (L7X) engines and Citroen/
Peugeot V6 (XFZ) engines (97-01).
• Kit contains locking pins for camshafts
and crankshaft, camshaft holding tool
and tensioner tools.
OFFER PRICE
£129.95 exc VAT
£155.94 inc VAT
OFFER PRICE
£114.95 exc VAT
£137.94 inc VAT
• Model No.
VS2112
• List Price
£224.95
Crankshaft Pulley Remover &
Installer - Ford
• Suitable
for
removal
and
installation
of free-floating
crankshaft pulley.
• Model No. VS1013
• List Price £152.95
£34.95 exc VAT
£41.94 inc VAT
£59.95 exc VAT
£71.94 inc VAT
Diesel Engine Setting/Locking Kit
Ford 1.6, 1.8, 1.9, 2.5 - Belt Drive
exc VAT
OFFER PRICE
OFFER PRICE
£119.95 exc VAT
£143.94 inc VAT
36
OFFER PRICE
OFFER PRICE
£89.95 exc VAT
£107.94 inc VAT
Petrol Engine Tensioner Locking Pins
VAG 1.6, 1.8,
2.0 - Belt Drive
• Set of timing belt
tensioner locking
pins for a wide variety
of VW, Audi and Seat
petrol and diesel vehicles.
• Holds back tensioner
assembly on cam belt
and auxiliary belt
during belt change.
• Model No. VSE1900
• List Price £10.95
OFFER PRICE
£5.95
£7.14
exc VAT
inc VAT
Prices exclude VAT unless stated otherwise
• Model No.
VS1213
• List Price
£185.95
Windscreen Removal
Tools Flat Blade
• Suitable for Sealey AK420,
WK020, WK021 and WK022
urethane cutting tools.
• Blades can be re-sharpened.
Model
No.
Width
List
Price
Exc.
VAT
Inc.
VAT
WK02005
16mm
£7.45
£3.45
£4.14
WK02006
13mm
£7.45
£3.45
£4.14
Promotion Code: VST12.09
1/2"Sq Drive Digital Torque Adaptor
with Angle Function 20-200Nm
5pc Flare
Nuts
Spanner
Set - Metric
NEW
• Drop-forged Chrome Vanadium steel with
contoured shafts.
• Fully hardened, tempered and chrome plated
with polished mirror finish for resistance to corrosion.
• Flare type spanner jaw suitable for most common
sizes of compression joint fittings.
• Five spanners covering ten sizes.
• Model No. AK2651
• List Price £39.95
OFFER PRICE
£21.95 exc VAT
£26.34 inc VAT
• Designed for use with a standard
ratchet or breaker bar.
• Ideal for work around the engine
bay and the tightening of wheel
nuts to factory specifications.
• Large LCD display with LED/audible
alarm indicating achieved and
target torque levels.
• Selectable readings in Nm, lb.ft, lb.
in or kg.m.
• Accurate to ±2% of stated capacity
and operates in either direction.
• Features angle mode, eliminating the need for angle
gauges and protractors providing the most accurate
and fastest way to measure torque plus angle tightening
sequences.
• Will also accumulate angle measurement when
multiple turns are required, ideal for use where
access is restricted.
• Model No. STW291
• List Price £129.95
NEW
OFFER PRICE
£59.95 exc VAT
£71.94 inc VAT
33pc 1/4"Sq Drive Socket Set
WallDrive® - Metric
41pc 3/8"Sq Drive Socket Set
WallDrive® - Metric
10pc 1/4", 3/8" & 1/2"Sq Drive
Hex Socket Bit Set - Stubby
• Deluxe professional socket set with standard and deep,
heat treated, mirror polished Chrome Vanadium steel
sockets.
• Covers sizes from 4 to 14mm.
• Features 48-tooth gear-to-gear comfort grip ratchet
handle, extension bars and accessories.
• Supplied in tough, durable
storage case with a contents
OFFER PRICE
map displayed on the
exc VAT
inside of the lid.
• Model No. AK8950
inc VAT
• List Price £67.45
• Deluxe professional socket set with standard and deep,
heat treated, mirror polished Chrome Vanadium steel
sockets.
• Covers sizes from 6 to 24mm.
• Features 48-tooth gear-to-gear comfort grip ratchet
handle, spark plug sockets, extension bars and
accessories.
• Supplied in tough, durable
carry-case with contents
OFFER PRICE
map displayed on the
exc VAT
inside of the lid.
• Model No. AK8952
inc VAT
• List Price £114.95
• Drop-forged Chrome Vanadium steel sockets, heat
treated and chrome plated with a fully polished
mirror finish for corrosion resistance.
• S2 Steel stubby hex bits with a zinc phosphate finish.
• Ideal for limited access applications.
• Contents: 4, 5, 6, 7, 8, 10,
12, 14, 17, 19mm.
OFFER PRICE
• Knurled ring for extra grip
exc VAT
with greasy fingers.
• Model No. AK6229
inc VAT
• List Price £33.95
23pc TRX-P* & Security TRX-TS* Bit
Set 1/4" & 3/8"Sq Drive
6pc Hammer-Thru
Screwdriver Set
£39.95
£47.94
• Comprises six sided TRX-P* and five sided security
TRX-TS* bits manufactured from S2 Chrome Vanadium
steel.
• TRX-P* fixings are now common place on new European
vehicles such as Renault, Vauxhall, Citroen and Peugeot.
• If a TRX-Star* bit is used on a TRX-P* fixing it can result
in damage to the fastener and tool. Using the correct
bit gives greater torque and minimises wear.
• TRX-TS* bits are suitable for a range of applications
such as fuel injection pumps and air conditioning units.
• Contents: TRX-P* Bits; TP10-TP60, Security TRX-TS* Bits;
TS10H-TS60H, Drive Adaptors;
1/4"Sq x 6mm Hex,
OFFER PRICE
3/8"Sq x 10mm Hex,
exc VAT
Magnetic Quick Chuck.
• Model No. AK6226
inc VAT
• List Price £36.95
£17.95
£21.54
Promotion Code: VST12.09
£64.95
£77.94
£20.95
£25.14
3pc Quick Release
Locking Pliers
Set
• Hardened and tempered
Chrome Vanadium steel
shafts with a satin polished
finish.
• Features hexagonal bolsters for use with a wrench.
• Contoured, textured handles with hammer caps.
• Shot blasted and blackened tips.
• Contents: Slotted; 5 x 100,
6 x 150, 8 x 175mm,
OFFER PRICE
Phillips; #1 x 75,
exc VAT
#2 x 100, #3 x 150mm.
• Model No. AK4932
inc VAT
• List Price £34.95
£19.95
£23.94
Prices exclude VAT unless stated otherwise
• Heat treated Chrome
Molybdenum and
Chrome Vanadium
steel construction with
a smooth satin finish.
• Deeply serrated and
hardened teeth grip the
workpiece from any angle.
• Curved jaw design applies
maximum pressure to all four corners of nut
or bolt heads making it ideal for high torque applications.
• Features one hand no-pinch quick release grip to
provide comfort and control, reduce hand fatigue
and are much easier to use than traditional style
locking pliers.
• Contents: 140 & 220mm
OFFER PRICE
Curved Jaw, 210mm
exc VAT
Long Nose.
• Model No. AK6863
inc VAT
• List Price £49.95
£29.95
£35.94
37
Motorcycle Storage
Shelters
NEW
• Made with 600D polyester
Oxford waterproof material.
• Easy to assemble and use.
• When shut can be locked
with a padlock (not included).
• Free standing or can be bolted
to a hard surface (bolts not included).
• Supplied with soft ground anchors.
• Will fit trikes, ATVs and ride on lawn mowers.
Side Stand Type Motorcycle Dolly
NEW
Model No. MS065
Model No.
Size
(L x W x H)
List Price
Exc. VAT
Inc. VAT
MS065
2700 x 1050 x 1550mm
£219.95
£149.95
£179.94
MS066
3450 x 1370 x 1900mm
£269.95
£179.95
£215.94
MS067
3450 x 1880 x 1900mm
£319.95
£199.95
£239.94
• Motorcycle dolly holds a single motorcycle or sport bike with a side stand, weighing
up to 565kgs.
• Easy manoeuvring around the workshop or garage.
• Front and rear lever operated wedge gates allow for easy loading and unloading.
• Five position side stand platform to fit varied length side stands.
• Front/rear steel pins to keep the motorcycle on the dolly
during moving, and smooth rolling dual castor wheels.
OFFER PRICE
• Overall Dimensions (L x W x H): 2120 x 770 x 90mm.
exc VAT
• Loading Track Dimensions (L x W x H): 2000 x 200 x 50mm.
• Model No. MS063
inc VAT
• List Price £179.95
£109.95
£131.94
Motorcycle Lift
450kg Capacity
Motorcycle Lift 365kg Capacity
FREE
Motorcycle Rear Lift
for MC450
•
•
•
•
•
•
•
•
•
•
•
Min./Max. Height: 220/760mm.
Working Platform Size (W x L): 480 x 1350mm.
All steel construction with foot operated, integral hydraulic pump and ram assembly.
Fitted with safety lock device to fix platform at three working heights of 760mm, 640mm
and 500mm and to prevent accidental lowering.
Suitable only for motorcycles with a centre stand.
Support platform fitted with full width loading ramp.
OFFER PRICE
Base assembly fitted with transport wheels and
exc VAT
lock-downs to prevent lift from moving during use.
Model No. MC365
inc VAT
List Price £469.95
£299.95
£359.94
Model No. MC450RL
List Price £34.95
• Min./Max. Height: 175/810mm.
• Platform (W x L): 145 x 2140mm.
• All steel construction with foot operated, integral
hydraulic pump and ram assembly.
• Fitted with platform safety lock device to prevent
accidental lowering.
• Base assembly fitted with transport wheels allowing
lift to be moved in horizontal or vertical position.
• Model No. MC450
• List Price £499.95
Hydraulic Mini Tractor/Quad/
Motorcycle Lift 700kg Capacity
Hydraulic Mini Tractor/Quad/
Motorcycle Lift 680kg Capacity
•
•
•
•
• All steel construction with heavy-duty hydraulic ram.
• Supplied with separate, foot operated, hydraulic pump
and reservoir unit.
• Features two additional side platforms for extra width.
• Ramp and platform made with chequer plate
surface to ease loading and positioning of mini tractor.
• Safety lock to prevent accidental lowering.
• Model No. MT680
• List Price £1499.95
Min./Max. Height: 180/900mm.
Platform Size (W x L): 950 x 2250mm.
All steel construction with heavy-duty hydraulic ram.
Full width ramp and platform with chequer plate
surface to ease loading and positioning of vehicle.
• Fitted with over-run guard at front of platform
and mechanical safety lock.
• Model No. MT700
• List Price £1599.95
38
OFFER PRICE
£899.95 exc VAT
£1079.94 inc VAT
Prices exclude VAT unless stated otherwise
OFFER PRICE
£349.95 exc VAT
£419.94 inc VAT
OFFER PRICE
£999.95 exc VAT
£1199.94 inc VAT
Promotion Code: VST12.09
Motorcycle Chain
Alignment Tool
Motorcycle Piston Ring
Compressing
Tool
6-8mm Carburettor Jet
Wrench Set
NEW
NEW
• Simple to use yet accurate tool for
correct alignment of the chain and
sprocket.
• Helps prevent wear
OFFER PRICE
to the chain and
exc VAT
sprockets.
• Model No. MS005
inc VAT
• List Price £19.95
£14.95
£17.94
Motorcycle Brake
Bleeder
• Used to
prevent
piston ring
damage while
installing the
cylinder head.
• Easily removed when cylinder is in place.
• Tool supplied with four
rings ranging from
Ø40-85mm.
OFFER PRICE
• Will fit most
exc VAT
engine sizes.
• Model No. MS006
inc VAT
• List Price £24.95
• Double end wrench
suitable for use with
6 & 8mm round jets.
• Single end wrench
for use on 6mm hex
jets.
• Model No. MS007
• List Price £17.95
1ltr Motorcycle
Portable Fuel
Tank
9pc Motorcycle
Fork Seal
Driver Kit
• Useful must have item, when needing to remove fuel
tank to perform maintenance on your motorcycle.
• Eliminates need to balance fuel tank in an awkward
position.
• Features 1ltr tank, 1200mm
OFFER PRICE
hose, two hose clamps
exc VAT
and on/off tap.
• Model No. MS029
inc VAT
• List Price £39.95
• Split design for easy
operation on both
conventional and USD
(inverted) forks for the installation of fork seals.
• Hardened and tempered carbon steel, finished
with zinc plating for corrosion resistance.
• Heavy knurled grip
gives positive purchase
OFFER PRICE
when in use and limits
exc VAT
risk of slip if hands are oily.
• Model No. MS018
inc VAT
• List Price £509.95
NEW
£19.95
£23.94
NEW
• One man bleeding/servicing of
hydraulic brakes and clutches.
• The kit utilises a small non-return valve
and two connector hoses that attach to
the scooter or motorcycle bleed nipple.
• As the brake/clutch are
bled the valve prevents
the used fluid and air
OFFER PRICE
being drawn back into
exc VAT
the system.
• Model No. MS014
inc VAT
• List Price £19.95
£11.95
£14.34
NEW
Model No. MS052
Motorcycle Fork
Seal Drivers
• Split design for easy operation on both conventional
and USD (inverted) forks for the installation of fork seals.
• Hardened and tempered carbon steel, finished with
zinc plating for corrosion resistance.
• Heavy knurled grip gives positive purchase when in
use and limits risk of slip if hands are oily.
• Limits potential damage to the forks caused by using
other methods.
Height Adjustable Front/Rear
Combination Stand
• Lifts and
stabilises
the front
or rear
of any
dual
sided
swing
armed
bike quickly
and easily.
• Supplied with width
and angle adjustable
rubber support pads
and front under fork
supports and
interchangeable
handles.
• Model No. RPS5
• List Price £79.95
Promotion Code: VST12.09
NEW
£22.95
£27.54
Model
No.
Seal
Driver
List
Price
Exc.
VAT
Inc.
VAT
MS052
33mm
£59.95
£31.95
£38.34
MS053
35-36mm
£60.95
£31.95
£38.34
MS054
39mm
£61.95
£31.95
£38.34
MS055
41mm
£62.95
£31.95
£38.34
MS056
43mm
£63.95
£31.95
£38.34
MS057
45mm
£64.95
£31.95
£38.34
MS058
46-47mm
£65.95
£31.95
£38.34
MS059
48mm
£65.95
£33.95
£40.74
MS060
49-50mm
£67.95
£33.95
£40.74
MS061
54mm
£68.95
£33.95
£40.74
Front/Rear
Combination Stand
NEW
OFFER PRICE
£54.95 exc VAT
£65.94 inc VAT
• Supplied with width and angle adjustable rubber
support pads and bobbin supports, front lifting pin
type supports and interchangeable handles.
• All supports mounted
on heavy-duty box
OFFER PRICE
section.
exc VAT
• Model No. RPS6
• List Price £49.95
inc VAT
£33.95
£40.74
Prices exclude VAT unless stated otherwise
OFFER PRICE
£10.95 exc VAT
£13.14 inc VAT
NEW
£239.95
£287.94
9pc Motorcycle Wheel
Bearing Removal
Kit
NEW
• For easy removal of wheel bearings.
• Covers sizes 10-25mm so should cover
most popular motorcycles and ATVs.
• Drift Shafts: 250, 400mm.
• Assorted Seal Collets
OFFER PRICE
Ø: 10, 12, 15, 17, 19,
exc VAT
20, 25mm.
• Model No. MS062
inc VAT
• List Price £79.95
£49.95
£59.94
Heavy-Duty Motorcycle
Front Wheel
Chock
NEW
• Fully adjustable to
fit wheels Ø15-18".
• Min./Max.tyre width
110/130mm.
• Features a pivot clamp which locks the
front wheel securely by the bike weight.
• Chock can be used free standing or
fixed (fixings not included).
• Please note: Motorcycle
OFFER PRICE
must also be secured
exc VAT
using tie-down straps.
• Model No. FPS7
inc VAT
• List Price £99.95
£59.95
£71.94
39
Motorcycle
Motorcycle Wheel Alignment
Tool
NEW
• Fast, simple and accurate alignment of rear
wheel.
• Optimises vehicle performance and set up
after installation or modification of the chain,
sprockets, brakes or suspension components.
• This fully portable kit is also ideal for trackday set up or for the motorcycle enthusiast.
• Model No. MS070
• List Price £349.95
ARRIVING
OCTOBER
OFFER PRICE
£249.95 exc VAT
£299.94 inc VAT
Calibration Rig for MS070
NEW
Calibration Charge
for MS070 Motorcycle
Wheel Alignment Tool
ARRIVING
OCTOBER
• Used to check and adjust the alignment of
the lasers on Model No. MS070 Motorcycle
Wheel Laser Aligner.
• This unit will allow workshops to check and
adjust in-house.
• Supplied with comprehensive instructions.
• Model No. MS070CR
• List Price £99.95
OFFER PRICE
£79.95 exc VAT
£95.94 inc VAT
Visit your online store and download the
FREE Sealey App today to view our
latest catalogue and promotions on
your iPad or iPhone.
Get your FREE
Catalogue
• RE-CALIBRATION SERVICE: We
offer a competitively priced
calibration service and
recommend the unit is returned
to us if the unit becomes
damaged or re-calibration is
required.
• Contact our technical help line
for further information on 01284
757505 and quote Model No.
MS070CAL.
• List Price £49.95
Your Local Dealer
Sealey Group
Kempson Way, Suffolk Business Park,
Bury St Edmunds, Suffolk IP32 7AR
01284 757500
01284 703534
email
Web
[email protected]
www.sealey.co.uk
Promotion valid from 1st September to 31st December 2012. Offers will be withdrawn
when stock is sold.
We reserve the right to change products and pricing at any time.
Specifications and descriptions on this promotion are given in good faith but
may change without notice and do not form any part of a sale contract E & OE.
40
To see Sealey’s impressive
full range of products browse
online at www.sealey.co.uk
or request a copy.
Prices exclude VAT unless stated otherwise
Promotion Code: VST12.09
*TRX-STAR, TRX-TS and TRX-P tools are suitable for driving TORX® and TORX PLUS® fasteners respectively. TORX® and TORX PLUS® are registered trademarks of Acument Intellectual Properties, LLC.
Tools & Equipment