Download Sharp CP-C410 Service manual
Transcript
CD-C410H,CP-C410 SERVICE MANUAL No. S5728CDC410H/ CD-C410H CP-C410 CD-C410H and CP-C410 constitute CD-C410H. • In the interests of user-safety the set should be restored to its original condition and only parts identical to those specified be used. • Note for users in UK Recording and playback of any material may require consent which SHARP is unable to give. Please refer particularly to the provisions of Copyright Act 1956, the Dramatic and Musical Performers Protection Act 1956, the Performers Protection Acts 1963 and 1972 and to any subsequent statutory enactments and orders. CONTENTS Page SAFETY PRECAUTION FOR SERVICE MANUAL ........................................................................................................... 2 IMPORTANT SERVICE NOTES (FOR UK ONLY) ............................................................................................................ 3 SPECIFICATIONS ............................................................................................................................................................. 3 NAMES OF PARTS ........................................................................................................................................................... 4 OPERATION MANUAL ...................................................................................................................................................... 6 DISASSEMBLY .................................................................................................................................................................. 7 REMOVING AND REINSTALLING THE MAIN PARTS ..................................................................................................... 9 ADJUSTMENT .................................................................................................................................................................. 10 NOTES ON SCHEMATIC DIAGRAM ............................................................................................................................... 12 BLOCK DIAGRAM ............................................................................................................................................................ 13 SCHEMATIC DIAGRAM / WIRING SIDE OF P.W.BOARD .............................................................................................. 16 WAVEFORMS OF CD CIRCUIT ....................................................................................................................................... 30 TROUBLESHOOTING (CD CHANGER CONTROL / CD SECTION) ............................................................................... 31 FUNCTION TABLE OF IC ................................................................................................................................................ 35 FL DISPLAY ...................................................................................................................................................................... 41 WIRING OF PRIMARILY SUPPLY LEADS (FOR UK ONLY) ......................................................................................... 41 REPLACEMENT PARTS LIST/EXPLODED VIEW PACKING METHOD (FOR UK ONLY) SHARP CORPORATION –1– CD-C410H,CP-C410 (Except for UK) SAFETY PRECAUTION FOR SERVICE MANUAL Precaution to be taken when replacing and servicing the Laser Pickup. The AEL (Accessible Emission Level) of Laser Power Output for this model is specified to be lower than Class I Requirements. However, the following precautions must be observed during servicing to protect your eyes against exposure to the laser beam. LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT (1) When the cabinet has been removed, the power is turned on without a compact disc, and the Pickup is on a position outer than the lead-in position, the Laser will light for several seconds to detect a disc. Do not look into the Pickup Lens. (2) The Laser Power Output of the Pickup inside the unit and replacement service parts have already been adjusted prior to shipping. (3) No adjustment to the Laser Power should be attempted when replacing or servicing the Pickup. (4) Under no circumstances look directly into the Pickup Lens at any time. (5) CAUTION - Use of controls or adjustments, or performance of procedures other than those specified herein may result in hazardous radiation exposure. (For UK) VARNING-OSYNLIG LASERSTRÅNING NÄR DENNA DEL ÄR ÖPPNAD. STIRRA EJ IN I STRÅLEN OCH BETRAKTA EJ STRÅLEN MED OPTISKA INSTRUMENT. VARO! AVATTAESSA OLET ALTTIINA NÄKYMÄTÖN LASERSÄTEILYLLE. ÄLÄ TUIJOTA SÄTEESEEN ÄLÄKÄ KATSO SITÄ OPTISEN LAITTEEN LÄPI. VARNING-OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD. STIRRA EJ IN I STRÅLEN OCH BETRAKTA EJ STRÅLEN GENOM OPTISKT INSTRUMENT. Laser Diode Properties Material: GaAIAs Wavelength: 780 nm Emission Duration: continuous Laser Output: max. 0.6 mW CAUTION-INVISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS. VARNING-OSYNLIG LASERSTRALNING NAR DENNA DEL AR OPPNAD. STIRRA EJ IN I STRALEN OCH BETRAKTA EJ STRALEN MED OPTISKA INSTRUMENT. ADVERSEL-USYNLIG LASERSTRALING VED ABNING. SE IKKE IND I STRALEN-HELLER IKKE MED OPTISKE INSTRUMENTER. VARO! AVATTAESSA OLET ALTTIINA NAKYMATON LASERSATEILYLLE. ALA TUIJOTA SATEESEEN ALAKA KATSO SITA OPTISEN LAITTEEN LAPI. VARNING-OSYNLIG LASERSTRALNING NAR DENNA DEL AR OPPNAD. STIRRA EJ IN I STRALEN OCH BETRAKTA EJ STRALEN GENOM OPTISKT INSTRUMENT. ADVERSEL-USYNLIG LASERSTRALING NAR DEKSEL APNES. STIRR IKKE INN I STRALEN ELLER SE DIREKTE MED OPTISKE INSTRUMENTER. –2– CD-C410H,CP-C410 FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL. IMPORTANT SERVICE NOTES (FOR UK ONLY) WITHSTANDING VOLTAGE TESTER Before returning the unit to the customer after completion of a repair or adjustment it is necessary for the following withstand voltage test to be applied to ensure the unit is safe for the customer to use. Setting of Withstanding Voltage Tester and set. Set name PROBE + AC OUT - set value SHORT-CIRCUIT AC POWER SUPPLY CORD Withstanding Voltage Tester Test voltage 4,240 VPEAK 3,000 VRMS Set time 6 secs Set current(Cutoff current) 4 mA UNIT CONNECT THE PROBE TO GND TERMINAL OF CHASSIS OF PHONO TERMINAL SCREW Unit Judgment OK: The “GOOD” lamp lights. NG: The “NG” lamp lights and the buzzor sounds. CHASSIS SCREW SPECIFICATIONS CD-C410H General Power source: Power consumption: Dimensions: Weight: Compact disc player section AC 230 V, 50 Hz 65 W Width; 270 mm (10-5/8") Height; 300mm (11-13/16") Depth; 359.5mm (14-3/16") 4.8 kg (10.6 lbs.) Type: Signal readout: PMPO; 68 W MPO; 34 W (17 W + 17 W) (DIN 45 324) RMS; 20 W (10 W + 10 W) (DIN 45 324) MPO; 34 W (17 W + 17 W) (10 % T.H.D.) RMS; 20 W (10 W + 10 W) (10 % T.H.D.) Speakers; 8 ohms Headphones; 16-50 ohms (recommended; 32 ohms) VIDEO/AUX (audio signal); 245 mV/47 kohms Frequency response: Signal/noise ratio: D/A Converter: Frequency response: Dynamic range: Amplifier section Output power: (Except for UK) Output power: (For UK) Output terminals: Input terminals: Cassette deck section Wow and flutter: (Except for UK) Wow and flutter: (Except for UK) 50 - 14,000 Hz (Normal tape) 55 dB (TAPE 1, playback) 50 dB (TAPE 2, recording/playback) 0.25 % (DIN 45 511) 0.15 % (WRMS) CP-C410 Speaker section Type: Maximum input power: Impedance: Dimensions: Tuner section Frequency range: 3-disc multi-play compact disc player Non-contact, 3-beam semi-con-ductor laser pickup 1-bit D/A converter 20 - 20,000 Hz 90 dB (1 kHz) FM; 87.5 - 108 MHz AM; 522 - 1,620 kHz Weight: 100 mm (4") full range speaker 20 W 8 ohms Width; 180 mm (7-1/8") Height; 300 mm (11-13/16") Depth; 204 mm (8") 2.1 kg (4.6 lbs.)/each Specifications for this model are subject to change without prior notice. –3– CD-C410H,CP-C410 NAMES OF PARTS CD-C410H 1 Front Panel 1. Disc Tray 2. Disc Number Indicator 3. Timer Indicator 4. Record Indicator 5. Sleep Indicator 6. Extra Bass Indicator: X-BASS 7. Function/CD Track/CD Counter/Frequency/Preset Channel/Volume/Timer/Sleep Time Indicator 8. Memory Indicator 9. FM Stereo Mode Indicator: ST 10. FM Stereo Indicator: 11. CD Play Indicator: 12. CD Repeat Indicator: 13. CD Pause Indicator: 2 1 2 34 5 6 REC X-BASS 3 SLEEP 11 12 13 7 14. On/Stand-by Switch 15. Extra Bass/Equalizer Mode Button 16. Volume Up/Down Buttons: 17. Random/Demo Button 18. Clock Button 19. Timer/Sleep Button 20. Function Selector Buttons 21. Memory/Set Button 22. Tuning and Time Up/Down Buttons: 23. Track Down/Review/Preset Down Button: 24. Play/Repeat Button: 25. Stop Button: 26. Track Up/Cue/Preset Up Button: 27. Disc Skip Button 28. Open/Close Button: 29. Record Pause Button: 30. Headphone Socket 8 9 10 MEMORY ST kHz MHz 15 16 17 14 18 19 20 21 22 23 24 25 26 27 28 29 30 31 31. (TAPE 1) Cassette Compartment 32. (TAPE 2) Cassette Compartment –4– 32 CD-C410H,CP-C410 CD-C410H Rear Panel 1. Video/Auxiliary (Audio Signal) Input Sockets 2. Speaker Terminals 3. AC Power Lead 4. FM 75 ohms Aerial Socket 5. AM Loop Aerial Input Socket 1 2 4 5 3 CP-C410 Speaker Section 6. Full Range Speaker 7. Bass Reflex Duct 8. Speaker Wire 6 7 8 1 Remote Control 1. Remote Control Transmitter LED CD Control section 2. Disc Number Select Buttons 3. Track Down/Review Button: 4. Track Up/Cue Button: 5. Disc Skip Button 6. Play/Repeat Button: 7. Stop Button: 8. Memory Button 9. Clear Button 10. Random Button 11. Pause Button: 5 6 2 3 4 7 8 13 14 15 19 Tuner control section 12. Preset Up/Down Buttons: Tape control section 13. (TAPE 1/2) Stop Button: 14. (TAPE 1) Play Button: 15. (TAPE 2) Record Pause Button: 16. (TAPE 2) Play Button: 17. (TAPE 2) Rewind Button: 18. (TAPE 2) Fast Forward Button: 9 10 11 12 16 17 18 20 21 22 19. Function Selector Buttons 20. Extra Bass/Equalizer Mode Button 21. Power Button 22. Volume Up/Down Buttons: –5– –6– 9 8 7 6 5 4 3 2 0:00 AM 0:00 TUNING/TIME ( ) MEMORY/ SET CLOCK ON/ STAND-BY AM 12:00 In this example, the clock is set for the 24-hour (0:00) system. SETTING THE CLOCK Press the ON/STAND-BY switch to enter the stand-by mode. or ) button to select the time Press the TUNING/TIME ( or ) button to adjust the minutes. Press the button for at least 0.5 seconds to change the time in 5 minute intervals. The hour setting will not advance even if minutes advance from "59" to "00". Press the MEMORY/SET button. Press the TUNING/TIME ( or ) button to adjust the hour. Press the TUNING/TIME button once to advance the time by 1 hour. Press for more than 0.5 seconds to advance continuously. When the 12-hour display is selected, "AM" will change automatically to "PM". Press the MEMORY/SET button. "0:00" → The 24-hour display will appear. (0:00 - 23:59) "AM 0:00" → The 12-hour display will appear. (AM 0:00 - PM 11:59) "AM 12:00" → The 12-hour display will appear. (AM 12:00 - PM 11:59) Press the TUNING/TIME ( display. Within 3 seconds, press the MEMORY/SET button. Press the CLOCK button. Perform steps 1 - 9 above. Press and hold down the VOLUME button, the button and the ON/STAND-BY switch all at the same time. Hold them for at least 2 second. (Refer to RESETTING THE MICROCOMPUTER on page 16.) Press the ON/STAND-BY switch to enter the stand-by mode. Note: The operation explained above will erase all data stored in memory, such as clock and timer settings, tuner and CD presets. 3 1 2 To switch the time display mode: The time display will appear for about 3 seconds. Press the CLOCK button. To see the time display: (When the power is ON) 1 Press the CLOCK button. 2 Within 3 seconds, press the MEMORY/SET button. 3 Perform steps 6 - 9 above. When the ON/STAND-BY switch is set to ON. 1 Press the MEMORY/SET button. 2 Perform steps 6 - 9 above. When the ON/STAND-BY switch is set to STAND-BY. To change the clock time: Press the MEMORY/SET button. The clock starts operating from "0" seconds. (Seconds are not displayed.) Note: In the event of a power failure or when the AC power lead is disconnected, the clock display will go out. When the AC power supply is restored, the clock display will flash on and off to indicate the time when the power failure occurred or when the AC power lead was disconnected. If this happens follow the procedure below to change the clock time. 9 7 8 5 6 1 2 3 4 15 15 Reset the microcomputer under the following conditions:To erase all of the stored memory contents (clock and timer settings, tuner and CD presets). If the display is not correct. If the operation is not correct. RESETTING THE MICROCOMPUTER 0.2 m - 6 m (8" - 20') PREPARATION FOR USE 2 1 Press and hold down the VOLUME button, the button and the ON/STAND-BY (POWER) switch all at the same time. Hold them for at least 1 second. Press the ON/STAND-BY (POWER) switch to enter the standby mode. Notes concerning use: Replace the batteries if control distance decreases or operation becomes erratic. Periodically clean the transmitter LED on the remote control and the sensor on the main unit with a soft cloth. Exposing the sensor on the main unit to strong light may interfere with operation. Change the lighting or the direction of the unit. Keep the remote control away from moisture, excessive heat, shock, and vibrations. CD-C410H,CP-C410 OPERATION MANUAL CD-C410H,CP-C410 DISASSEMBLY Caution on Disassembly Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure excellent performance: 1. Take cassette tape and compact disc out of the unit. 2. Be sure to remove the power supply plug from the wall outlet before starting to disassemble the unit. 3. Take off nylon bands or wire holders where they need be removed when disassembling the unit. After servicing the unit, be sure to rearrange the leads where they were before disassembling. 4. Take sufficient care on static electricity of integrated circuits and other circuits when servicing. CP-C410H Top Cabinet ( A1 ) x2 ø3 x12mm Side Panel (Right) ( A1 ) x2 ø3 x12mm ( B1 ) x1 ø3 x10mm CD-C410H STEP REMOVAL PROCEDURE FIGURE 1 Top Cabinet 1. Screw ..................... (A1) x4 7-1 2 Side Panel (Left/right) 1. Screw ..................... (B1) x6 7-1 3 CD Player Unit/ CD Tray Cover 1. Turn on the power supply, open the disc tray, take out the CD cover, and close. (Note 1) 2. Hook ....................... (C1) x3 3. Hook ....................... (C2) x2 4. Socket .................... (C3) x4 7-2 1. Screw ..................... (D1) x5 7-2 ( B1 ) x2 ø3 x12mm ( B1 ) x1 ø3 x10mm Figure 7-1 CD Tray Cover Push Back Board 5 Main PWB/ 1. Screw ..................... (E1) x12 Display PWB/ 2. Socket .................... (E2) x4 Headphone PWB 8-1 6 Front Panel 1. Screw ..................... (F1) x2 2. Hook ....................... (F2) x2 8-1 7 Tape Mechanism 1. Open the cassette holder. 2. Screw...................... (G1) x6 8-2 8 Turntable 1. Screw ..................... (H1) x1 2. Cover ...................... (H2) x1 8-3 9 Disc Tray 1. Screw ..................... (J1) x2 2. Guide ...................... (J2) x2 8-3 10 CD Changer Mechanism 1. Screw ..................... (K1) x4 8-4 CD Mechanism 1. Screw ..................... (L1) x1 Driver CD Player Unit Hook ( C2 ) x1 Push Driver ( D1 ) x1 ø3 x12mm ( D1 ) x4 ø3 x12mm ( C3 ) x1 ( C3 ) x3 Back Board 8-4 Figure 7-2 Note 1: How to open the changer manually. (Fig. 7-3) 1. Insert the tip of fine screwdriver into the hole of CD player base, and press down the worm wheel < A > . 2. Then, turn fully the lock lever in the arrow direction through the hole on the loading chassis bottom in this state. After that, push forward the CD player base. <A> CP-C410 STEP 1 REMOVAL Speaker PROCEDURE 1. Front panel ............. (A1) x1 2. Screw ..................... (A2) x4 Hook ( C1) x3 Hook ( C2 ) x1 4 11 Side Panel (Left) ( B1 ) x2 ø3 x12mm FIGURE LOCK LEVER 9-5 9-6 Figure 7-3 –7– CD-C410H,CP-C410 Display PWB ( K1 ) x4 ø3 x12mm Front Panel ( E1 ) x9 ø3 x10mm ( L1 ) x1 ø2.6 x10mm ( E1 ) x1 ø3 x10mm Shift Lever ( E2 ) x2 CD Changer Mechanism Tape Mechanism ( E1 ) x1 ø3 x8mm Main PWB ( E2 ) x1 CD Player Base CD Mechanism Care when installing the CD changer mechanism. Install the CD changer mechanism on the CD player base after the shift lever has been set in the highest position. Figure 8-4 ( E1 ) x1 ø3 x8mm Figure 8-1 CP-C410 Front Panel ( E2 ) x1 ( G1 ) x6 ø3 x10mm Front Panel (A1) x1 Open Cassette Holder Power Supply PWB ( F1 ) x2 ø3 x10mm Tape Mechanism Speaker Box Screw driver Figure 8-2 Driver should be pried away from speaker Box. ( H1 ) x1 ø3 x10mm Direction of handle ( H2 ) x1 Figure 8-5 Speaker Box Turntable Disc Tray ( J1 ) x1 ø3 x10mm Woofer ( J2 ) x1 (A2) x4 4 x32mm ( J1 ) x1 ø3 x10mm CD Player Unit ( J2 ) x1 Figure 8-6 Figure 8-3 –8– CD-C410H,CP-C410 REMOVING AND REINSTALLING THE MAIN PARTS CD MECHANISM SECTION Perform steps 1, 2, 3, 10 and 11 of the disassembly method to remove the CD mechanism. Loading Motor How to remove the loading motor (See Fig. 9-1) 1. Remove the screws (A1) x 2 pcs., to remove the loading motor. ( A1 ) x2 ø2 x5mm Figure 9-1 How to remove the pickup (See Fig. 9-2) 1. Remove the screws (C1) x 2 pcs., to remove the shaft (C2). 2. Remove the stop washer (C3) x 1 pc., to remove the gear (C4). 3. Remove the pickup. ( C1 ) x2 2.6 x6mm Pickup ( C2 ) x1 ( C3 ) x1 CD Mechanism ( C4 ) x1 Figure 9-2 –9– CD-C410H,CP-C410 ADJUSTMENT MECHANISM SECTION TUNER SECTION • Driving Force Check fL: Low-range frequency fH: High-renge frequency • AM IF/RF Signal generator: 400 Hz, 30%, AM modulated Torque Meter Specified Value Play: TW-2412 Tape 1: Over 80 g Tape 2: Over 80 g • Torque Check Torque Meter Tape 2 30 to 60 g. cm 30 to 60 g.cm Fast forward: TW-2231 — 60 to 120 g.cm Rewind: TW-2231 — 60 to 120 g.cm IF 450 kHz 1,620 kHz Band Coverage — 522 kHz (fL): T302 *2 1.1 ± 0.1 V Tracking 990 kHz 990 kHz (fL): T302 Test Tape Adjusting Point Specified Value MTT-111 Volume in motor. 3,000 ± 30 Hz Setting/ Instrument Adjusting Connection Parts T351 *1 *1 *1. Input: Antenna, Output: TP302 *2. Input: Input is not connected, Output: TP301 • Tape Speed • Setting the Test Mode Keeping the TUNING (DOWN) button and MEMORY button pressed, turn on POWER. Then, the frequency is initially set in the memory as shown in Table. Call it with the PRESET button to use it for adjustment and check of tuner circuit. Instrument Connection Speaker terminal (Load resistance: 8 ohms) Preset No. FM Preset No. 1 2 3 4 5 87.50 MHz 108.00 MHz 90.00 MHz 106.00 MHz 98.00 MHz 6 7 8 9 10 TAPE MECHANISM AM 522 kHz 1,620 kHz 603 kHz 1,404 kHz 990 kHz 11 ~ 40 • FM Mute Level Signal generator: 1 kHz, 40 kHz dev. FM modulated. MM 1 Motor Frequency Display Frequency Volume in motor 98.00 MHz (25 dBµV) 98.00 MHz Adjusting Parts VR351 *1 Instrument Connection Input: So301 Output: Speaker Terminal *1. Adjust so that an output signal appears TUNER PWB TP301 FE301 Normal speed Frequency Display Specified Value Tape 1 Play: TW-2111 Test Stage Frequency T351 VR351 FM MUTE AM IF LEVEL 1 T302 IC303 13 L311 21 R331 TP302 AM BAND COVERAGE fL AM TRACKING fL Figure 10-1 ADJUSTMENT POINTS – 10 – SO301 ANTENNA TERMINAL CNP301 CD-C410H,CP-C410 TEST MODE • Setting the test mode Any one of test mode can be set by pressing several keys as follows. <REC. PAUSE> + <DISC. SKIP> + <POWER> TEST: CD operation test • TEST mode Function — CD test mode Setting of TEST mode Indication of CD TST mode (Fig. 11-1) IL is not performed. OPEN/CLOSE operation is manual operation. The pickup can be moved by using the ( <MEMORY> LASER ON <MEMORY> Tracking on the spot. SERVO OFF PLAY <PLAY> key input ) or ( ) key. <STOP> STOP <MEMORY> Tracking on the spot. SERVO ON PLAY TOC. IL is performed, and the ordinary PLAY is performed. If the following key is pressed during PLAY, it is possible to specify directly any Track No. <Disc Number 1> key: Track 4 <Disc Number 2> key: Track 9 <Disc Number 3> key: Track 15 Note: Only in STOP state it is possible to slide the pickup with the ( VOL. --- Last memory BAL. --- CENTER R.GEQ. --- FLAT 1 X-BAS --- OFF ) or ( 2 Press <STOP> key. Stop ) key. 3 Canceling method - POWER OFF Figure 11-1 CD SECTION Since this CD system incorporates the following automatic adjustment function, when the pickup is replaced, it is not necessary to readjust it. Since this CD unit does not need adjustment, the combination of PWB and laser pickup unit is not restricted. • Automatic adjustment item 1. Focus offset (Fig. 11-2) 2. Tracking offset (Fig. 11-3) 3. E/F balance (tracking error balance) (Fig. 11-4) 4. RF level AGC function (HF level: constant) 5. RF level automatic follow-up of the tracking gain This automatic adjustment is performed each time a disc is changed. Therefore, each disc is played back using the optimal settings. Enlarged View 10ms 0.50 V IC1 20 FE 0.1s 0.50 V IC1 20 FE FOCUS OFF-SET ADJUST 10ms 0.50 V IC1 7 TE 0.1s 0.50 V IC1 7 TE TRACKING OFF-SET 1 ADJUST TRACKING OFF-SET ADJUST 1 2 2 Figure 11-3 Figure 11-2 TRACKING/ ERROR BARANCE 1 ADJUST 200 ms 1V/diV IC 1 15 TO 200 ms 1V/diV IC 1 7 TE 2 Figure 11-4 – 11 – CD-C410H,CP-C410 NOTES ON SCHEMATIC DIAGRAM • The indicated voltage in each section is the one measured by Digital Multimeter between such a section and the chassis with no signal given. 1. In the tuner section, ( ) indicates AM < > indicates FM stereo 2. In the main section, a tape is being played back. 3. In the deck section, a tape is being played back. ( ) indicates the record state. 4. In the power section, a tape is being played back. 5. In the CD section, the CD is stopped. • Parts marked with “ ”( ) are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. • Resistor: To differentiate the units of resistors, such symbol as K and M are used: the symbol K means 1000 ohm and the symbol M means 1000 kohm and the resistor without any symbol is ohm-type resistor. Besides, the one with “Fusible” is a fuse type. • Capacitor: To indicate the unit of capacitor, a symbol P is used: this symbol P means micro-micro-farad and the unit of the capacitor without such a symbol is microfarad. As to electrolytic capacitor, the expression “capacitance/withstand voltage” is used. (CH), (TH), (RH), (UJ): Temperature compensation (ML): Mylar type (P.P.): Polypropylene type • Schematic diagram and Wiring Side of P.W.Board for this model are subject to change for improvement without prior notice. REF. NO DESCRIPTION POSITION REF. NO SW713 DESCRIPTION POSITION SW1 OPEN/CLOSE ON—OFF DOWN ON—OFF SW2 MECHA UP ON—OFF SW714 TUNING UP ON—OFF SW3 DISC NUMBER ON—OFF SW715 TUNING DOWN ON—OFF SW4 PICKUP IN ON—OFF SW717 POWER ON—OFF SW701 RANDOM/DEMO ON—OFF SW718 CLOCK ON—OFF SW702 VOLUME DOWN ON—OFF SW719 TIMER/SLEEP ON—OFF SW703 X-BASS ON—OFF SW721 MEMORY/SET ON—OFF SW704 VOLUME UP ON—OFF SW722 CD ON—OFF SW705 OPEN/CLOSE ON—OFF SW723 TUNER ON—OFF SW706 DISC SKIP ON—OFF SW724 TAPE ON—OFF SW709 REC./PAUSE ON—OFF SW725 AUX ON—OFF SW710 UP ON—OFF SWM 3 FOOL PROOF ON—OFF SW711 STOP ON—OFF SWM 4 F.A.S. ON—OFF SW712 PLAY ON—OFF SWM 5 CAM ON—OFF FRONT VIEW FRONT VIEW E C B (S) (G) (D) (1) (2) (3) B C E (D)(G) (S) (3) (2) (1) 2SA1015 GR 2SB561 C 2SC2389 SS 2SC535 C KRA102 M KRA109 M KRC102 M KRC104 M KRC107 M KTA1266 GR KTA1273 Y KTC3199 GR KTC3203 Y 2SD2012 Y Figure 12 TYPES OF TRANSISTOR – 12 – KDV147B – 13 – Figure 13 BLOCK DIAGRAM (1/3) M M PICKUP IN SW4 M1 SPIN MOTOR M2 SLIDE MOTOR TRACKING COIL FOCUS COIL 24 25 30 31 12 13 6 7 1 2 3 4 22 32 8 9 10 11 IC5 M56748FP DRIVER 5 26 27 28 29 34 35 36 20 30 31 54 SERVO AMP. 15 16 27 23 29 FIN2 FIN1 E F LA9240M IC1 64 VCC1 62 LD0 TO FD SPO SP SLD JP– 32 CV+ 40 SLC 43 SL1 44 ~ Q1 SL– SL+ DRF 20 JP– PU-IN SW +B1 SL+. SL–. DRF CL, DAT, SELIAL CONTROL/CE 51 52 53 44 XOUT 45 XIN XL1 6 23 36 41 43 +5V LCHO 37 53 ~ 58 Q91 Q93 26 RES. CQCK. COIN SQOUT. RWC. WRQ +5V 9 CONT2 25 +12V(+B5) 1 CONT1 24 IC2 LVSS 38 RVSS 39 LC78622U RCHO 40 9 EFMO SERVO/SIGNAL 10 EFMIN 12 CLV+ CONTROL ~ +5V CL DAT CE VVDD VDD LVDD RVDD XVDD PICKUP UNIT 7 Q81 9 8 7 6 5 4 3 2 1 +B1 CNS10 9 8 7 6 5 4 3 2 1 10 +5.6V (B1) MECHA UP GND (D) DISK NO. OPEN/CLOSE GND (D) M– M+ GND (M) 10 GND (D) 5 6 CNP10 REGULATOR 3 IC91 TA7291S LOADING MOTOR DRIVER SOLM1 M3 LOADING SW1 OPEN/CLOSE SW3 DISC No. SW2 MECHA UP TO DISPLAY SECTION M ( TO IC401 ) TO MAIN SECTION CD-C410H,CP-C410 CD-C410H,CP-C410 +B4 +B6 FM IF AM IF CF302 T351 FM IF IN 5 2 6 4 VCC 3 7 2 MIX OUT 1 VR351 FM MUTE LEVEL 3 REG 4 21 10 IF OUT 22 AM RF IN FM OSC 17 7 6 18 16 13 14 15 L-CH R-CH 12 MUTING Q35 Q35 +B6 BALUN VOLTAGE REGURATER +B4 AM BAND COVERAGE X352 4.5MHz VT 20 12 1 22 OSC SWITCHING FM Q360 10 16 11 3 4 5 6 IC302 LC72131 PLL 13 17 21 ST 7 15 CE DI CL DO T304 AM AMT. FM IN AM TRACKING AM IN L311 23 AM OSC OUT AM OSC IN 24 8 9 FM DET MONO/ST IC303 LA1832 FM IF DET./FM MPX./AM IF AFC AM LOOP ANTENNA 5 L354 FM/AM Q301 CF301 X351 1 SD FE301 FM FRONT END 8 CF351 ANTENNA TERMINAL STEREO SO301 ST FM +B4 Q361 SO401 VIDEO/AUX. TAPE TUNER CD FROM CD SECTION PLAYBACK&RECORD/ PLAYBACK AMP. IC101 AN7345K TAPE 1 PB HEAD L-CH R-CH Q106 REC P.B L REC 9 R REC 16 AC BIAS REF +B4 13 L 4 R 21 L NF 3 R NF 4 POP REDUCE 6 REC P. B. L (T2) 2 R (T2) 23 ~ TAPE 2 REC/PB HEAD L-CH R-CH L (T1) 1 R (T1) 24 SWITCHING Q103 Q121 Q122 MUTING P. B L R 5 20 T1/T2 REC H/N 7 L REC R 8 L NF 17 R NF 10 ALC 18 14 T1/T2 12 19 T1/T2 SWITCHING SWITCHING Q107 Q108 Q111 Q109 Q110 SWITCHING BIAS OCS ERASE HEAD Q128 L104 SWITCHING BIAS Q124 Q126 Figure 14 BLOCK DIAGRAM (2/3) – 14 – BIAS CD-C410H,CP-C410 +B2 UNSWITCH +B1 FL701 DISPLAY 3 ~ MEMORY BACK UP 30 31 32 33 13 Q701 14 15 M IF TO CD SECTION TO CD SECTION TAPE BIAS TAPE REC T1/T2 CD DSP WRQ CD DSP RWC CD DSP CQCK CD DSP COIN CD DSP SQOUT RESET CD DSP RES CD T/T OPEN/CLOSE 6 1 2 CD UP DOWN/DISC NO T2 RRUN PLSE L-CH INPUT R-CH INPUT MONO/ST L-CH R-CH FM/AM 12 MUTING Q353 Q354 9 7 8 10 11 12 13 14 15 16 17 18 19 20 TO POWER SECTION +B5 PHM1 21 22 23 24 25 KEY SW701 ~ 6 ~ 72 TAGE ATER B4 29 IC701 IX0191AW SYSTEM CONTROL MICROCOMPUTER 1 80 71 70 30 ~ 27 ~ +B6 VDD +B2 AVDD AVREF SW725 33 34 XL702 4.19MHz 35 36 ~ 37 65 38 64 ~ 39 40 61 CL DE DI DO DRF TO CD SECTION RESET 13 17 POWER CD SL– CD SL+ CD PUIN 6 VDD TAPE MOTOR TAPE SOL DO TAPE MECHASTOP T1 RUN PLSE TAPE FP 60 59 58 57 56 55 54 53 52 51 50 49 43 48 47 46 45 44 43 42 41 RESET Q708 Q709 ZD701 SYSTEM STOP TO CD SECTION SWM3 FOOL PROOF 21 SWM4 F. A. S 1 ST FM +B2 SOLM1 SOLENOID Q707 RX701 2 3 SWM5 CAM PRESET GRAPHIC EQUALIZER CL DI CE +B4 23 24 25 7 42 5 44 8 41 IC401 LC75394E AUDIO PROCESSOR 17 32 6 43 9 40 IC801 LA4551 POWER AMP. 49 VOLUME OUT L R 58 55 13 R-IN 9 L-IN L-OUT 2 5 R-OUT 7 VCC MUTE L R 19 30 CD L R 21 28 14 GRAPHIC EQUALIZER 14 35 56 63 50 26 27 8 12 37 11 38 10 12 NF 3 J801 HEADPHONES 4 11 + – 39 SO801 FRONT SPEAKER TERMINAL X-BASS VOLTAGE REGULATOR +B1 TO CD SECTION +B1 +B4 +B5 UN-SWITCHED +5.6V Q952 Q953 D965 ~ D968 +5.6V F962 T2.5A L 250V VOLTAGE REGULATOR +12V (ANALOG) +12V (MOTOR) Q942 Q941 D961 ~ D964 Q943 VOLTAGE REGULATOR ZD972 D971 Q971 VOLTAGE REGULATOR ~ TUNER VSS AVSS L R 45 64 LVREF R 4 57 VDD 16 33 RVREF TAPE L VREF SO401 VIDEO/AUX. AC POWER SUPPLY CORD D973 F963 T1.6A L 250V T.F AC 230 V, 50 Hz Figure 15 BLOCK DIAGRAM (3/3) – 15 – CD-C410H,CP-C410 TO A 11 4 5 6 7 12 R31 P19 7 - H TO MOTOR PWB CNS10 B C E IC91 R96 R95 Q93 C702 25 26 27 R732 R794 24 C17 R736 R749 R730 28 R737 30 SW725 VIDEO/AUX R761 L701 32 33 1 2 3 R785 F R776 R786 ZD701 R798 R795 R782 D704 D706 D705 C709 SW709 REC/PAUSE R763 R767 R773 C146 R150 R134 B C E 1 2 3 Q107 C107 C102 C108 R108 B C E Q111 1 2 3 Q110 1 2 3 R110 Q108 F1 T500mA L 250 C453 SW702 VOL-DOWN C809 R811 C843 C844 R777 R835 J801 R809 C813 R836 HEADPHONES DISPLAY PWB-A2 HEADPHONS PWB-A3 CNS101 P18 2 - H TO TAPE MECHANISM H • The numbers 1 to 12 are waveform numbers shown in page 30. 2 2 C1 R102 R107 C1 C454 G 1 20 SW705 OP/CL SW701 RANDOM/DEMO SW704 VOL-UP C111 R117 C101 SW706 D-SKIP R701 SW703 X-BASS R101 B C E 5 1 C115 R119 L107 C117 C123 R764 Q707 Q708 B C E D703 C707 C708 15 3 4 Figure 16 WIRING SIDE OF P.W.BOARD (1/4) – 16 – 5 6 C812 Q701 R779 R781 R780 1 2 3 C C121 R123 C855 C710 Q709 C711 R734 R741 R717 R719 R721 R713 R715 R716 R718 R720 R723 R725 D701 R762 R766 10 C131 C128 C127 R125 R121 R772 C147 12 C133 R172 R133 C705 R722 C141 C139 R139 R145 R131 SW710 UP R768 C119 C701 29 C57 R135 C129 R754 C148 R137 IC101 R733 B C E C113 80 23 R141 C135 Q121 R152 SW724 TAPE 31 L1 R88 R87 R86 C58 D7 D5 R756 R109 PLAY SW712 5 R757 22 C22 C96 R778 R750 R751 10 21 E R61 R792 R746 R745 R738 15 70 75 20 20 IC701 60 R60 R47 R46 R45 CNP101 64 65 19 R755 R154 18 R739 R153 17 R58 XL1 R752 C54 C56 C55 PINK 55 50 R740 TUN SW723 C46 PK 55 R57 1 64 60 48 49 R70 R77 R78 R49 16 25 24 45 R35 R56 5 IC2 40 C43 R71 R72 R79 BLACK 30 30 35 R82 STOP SW711 BK 50 35 R793 15 C703 WHITE 45 14 XL701 WH(W) 13 32 33 R38 10 25 R744 C704 GRAY 17 16 15 20 R742 R3 C3 R3 C53 C59 SW713 DOWN C51 41 40 12 VIOLET R20 D81 C20 R26 CD SW722 R797 11 VL C15 C16 C52 10 GY R19 R21 C81 1 2 3 CD SW722 R703 R705 R707 R709 R731 R726 R727 R748 BLUE R735 R747 GREEN BL R724 GR R22 C19 SW714 TUN-UP R27 R81 R704 YELLOW R702 ORANGE YL R708 OR R714 RED R706 RD(R) 3 4 5 6 7 8 9 R23 Q81 R712 BROWN FL701 D BR C C18 R25 R24 Q91 R54 R30 SW721 MEMORY/SET D91 C11 E C B R743 COLOR TABLE 18 R39 C718 1 2 10 15 SW715 TUN-DOWN R783 C 5 CNP10 R774 R711 R603 19 20 25 R799 1 2 3 CNSM1 C715 8 30 IC5 R788 Q705 R758 Q706 E C B RX701 WH GY WH TIMER/SLEEP SW719 R760 GY 35 1 9 8 7 6 5 4 3 2 1 R98 R771 C706 BIM01 WH GY WH E C B R759 1 D702 P18 2 - A CNPM1 TO TAPE MECHANISM PWB 1 2 3 4 5 6 7 8 9 10 11 12 R99 C91 R775 R765 RD R789 B C95 10 9 8 7 6 5 4 3 2 1 SW718 CLOCK R769 R97 SW717 POWER D709 D708 C717 L700 C44 36 CD-C410H,CP-C410 P18 6 - H TO CD MOTOR PWB CNS3A 7 12 1 R43 10 5 4 3 2 1 1 2 3 4 5 6 7 8 C7 R13 C13 R2 C14 15 20 25 40 1 2 3 C455 R422 R406 R972 C973 D971 D972 R844 C849 C845 C853 C851 C847 R982 C852 C848 C956 D968 C955 D966 Q106 D965 C824 C823 R825 R114 C829 R808 R804 R807 C804 R803 R806 C803 R805 C831 C802 Q942 1 2 3 4 5 6 7 8 9 10 11 12 13 14 B C E B C E L832 R104 C820 D973 D967 R106 F1 T500mA L 250V C974 ZD971 C975 R421 C944 C828 R115 L-CH R843 C850 C846 R981 C109 R113 R105 C871 C872 C953 R953 C954 E C B D963 R174 Q124 E C B R845 SO801 SPEAKERS RATED SPEAKER IMPEDANCE :8OHMS MIN. C957 Q941 B C E L831 Q110 R110 Q108 L104 R166 B C E E C B C116 R120 Q103 R103 E C B 7 6 5 4 3 2 1 C962 R-CH ZD951 R952 C952 1 2 3 C151 R168 Q943 B C E C101 Q111 1 2 3 Q109 Q107 C107 C102 C108 R108 CNP102 C113 24 C114 R102 R107 C112 B C E 1 2 3 R109 R101 CNP101 C111 R117 C428 B C E Q128 C945 1 C115 R119 L107 C426 C152 R167 C972 C961 C441 R164 C132 R126 C124 R124 C118 C122 R122 L108 C120 Q105 CNP901 6 5 4 3 2 1 R479 C825 IC101 20 5 C435 C437 C439 50 C440 C438 C436 C434 R480 C442 C424 B C E R162 C153 C130 R138 R132 C121 48 49 C971 D401 R140 C134 15 C420 C422 Q126 10 C131 C128 C127 45 C427 L-CH C408 Q971 R977 55 C418 R160 R118 C106 R112 C105 R111 Q104 12 C133 40 1 64C433 C452 L105 C145 C142 C140 R146 13 5 60 C943 C146 Q122 R150 R134 R152 C147 R414 R412 C414 R476 C423 10 IC401 D964 C406 R136 R158 R142 C136 C148 R137 C141 C139 C412 B C E SO401 VIDEO/AUX R407 D961 C405 30 35 C425 C976 ZD972 R976 R975 R978 B C E Q953 C92 C68 R141 15 20 32 33 R974 E C B C421 D962 C402 25 C67 R45 C135 R419 R420 C417 C419 17 16 R418 R973 C445 R47 R46 48 49 C451 R415 R416 R943 50 C407 C413 C401 R60 R-CH R408 R411 C827 C22 R58 R413 R475 R405 C409 C942 C41 R18 C443 C42 R57 C410 R477 60 55 R56 C33 R36 C34 C411 R478 IC2 0 45 1 64 C97 C37 D2 R815 5 C39 C35 C808 10 5 C38 C50 C31 R37 R35 C40 R73 C69 R75 15 20 R38 55 50 R74 C70 R76 17 16 1 64 C2 R1 48 49 R41 C45 C30 R33 C32 R34 R32 C53 C1 5 60 R951 45 E C B Q81 10 IC1 C444 30 35 ZD941 32 33 C3 R403 R402 R401 C81 D81 C20 R26 C52 R27 R81 C403 R20 R4 C5 R3 C10 C404 C15 C16 R5 R944 R19 R21 R8 C806 R22 C19 R11 R15 R16 R948 C948 R23 R14 R945 R17 C947 C12 C830 C17 C11 C18 C446 C4 C6 R9 C941 R949 R12 R28 R417 R39 D402 R29 18 3 CNP402 1 2 3 4 5 6 7 8 9 10 R6 C9 R7 C94 MAIN PWB-A1 2 R946 R10 C21 10 15 C150 25 5 9 D404 D403 CNP1 CNP2 C8 19 20 R947 C44 8 C24 E C B Q1 6 5 4 3 2 1 CNP3 R42 R31 C25 6 P18 5 - D TO PICKUP UNIT CNS1A P18 5 - D TO PICKUP UNIT CNS2A B C E Q952 IC801 C453 C810 C809 C801 R809 C813 R812 CNS901 P19 10 - B TO POWER PWB C812 R811 R810 C814 C454 CNS102 P18 3 - H TO TAPE MECHANISM H HANISM 7 8 9 10 Figure 17 WIRING SIDE OF P.W.BOARD (2/4) – 17 – 11 12 CD-C410H,CP-C410 P16 1 - C TO DISPLAY PWB CNSM1 PICKUP UNIT A SWM4 F. A. S BROWN RD(R) RED OR ORANGE YL YELLOW GR GREEN BL BLUE VL VIOLET GY GRAY WH(W) WHITE BK BLACK PK PINK 1 2 3 4 5 6 7 8 CNS2B CNPM2 BL PK WH YL BK CNS1B 1 2 3 4 5 BK WH C BK WH PK YL BL 1 2 RD WH GY WH GY WH GY WH FWM2 B BR CNPM1 12 11 10 9 8 7 6 5 4 3 2 1 R COLOR TABLE 1 2 3 4 5 SOLM1 SOLNOID 1 2 3 4 5 6 7 8 CNS1A CNS2A SWM5 CAM SWM3 F. P. CNP1 P17 9 - A TO MAIN PWB FWM1 D 1 WH 2 BK CNP2 P17 8 - A TO MAIN PWB M1 DISC MOTOR PHM1 4 3 E 1 2 MM1 TAPE MOTOR + M2 SW4 PICK UP IN SLIDE MOTOR TAPE MECHANISM PWB-C + TAPE 1 TAPE 2 PLAY BACK HEAD(55) ERASE HEAD(56) RECORD/PLAY BACK HEAD(55) F CNP3A WH WH BK YL BK BL PK 1 2 3 4 5 6 BK PK WH CD MOTOR PWB-D GY BR GY 1 2 3 4 5 6 BK WH PK BK BL YL WH 7 6 5 4 3 2 1 CNS102 3 2 1 CNS101 RD BK WH RD WH GY WH GY WH G CNS3B 1 2 3 4 5 6 CNP102 P17 8 - H TO MAIN PWB CNP101 P16 6 - H TO MAIN PWB CNP3 P17 7 - A TO MAIN PWB H 1 2 CNS3A 3 4 Figure 18 WIRING SIDE OF P.W.BOARD (3/4) – 18 – 5 6 CD-C410H,CP-C410 TUNER PWB-B1 POWER PWB-B2@@ F963 T1.6A L 250V CNS901 R362 R361 C365 C353 IC303 L354 R330 C367 C366 20 R351 24 C363 C350 3 2 1 C364 C325 C361 R358 VR351 C362 L353 C341 R380 C394 C381 R381 C334 C331 Q301 T302 R320 C322 R310 C320 L311 C327 R399 D362 D311 C321 5 6 7 8 D312 FE301 C332 R323 L312 C323 B C E R315 R307 R305 R304 1 2 3 R318 1 2 3 4 CNP301 1 2 SO301 FM 75 OHMS SW3 DISC NUMBER CNS5 2 1 MOTOR PWB-E SW2 MECHA UP SW1 OPEN/CLOSE M3 T/T OP/DOWN CNS10 OR BR WH GY WH GY WH GY WH RD 1 - SOLENOID SOLM1 BIM5 TO MAIN PWB CNP10 P16 4 - B 10 9 8 7 6 5 4 3 2 1 AM LOOP ANTENNA 2 1 + 6 7 8 9 10 Figure 19 WIRING SIDE OF P.W.BOARD (4/4) – 19 – R356 X351 R355 R353 CF302 C351 C352 C342 R366 R365 R368 R363 R364 R354 R377 C358 C357 C396 L351 IC302 C383 R352 C393 CF301 5 15 D361 X352 12 13 14 R398 15 16 C385 17 18 19 R379 20 21 C392 22 C382 10 1 C387 R331 13 C399 C398 C354 C355 R360 C386 R376 9 8 7 6 5 4 3 2 1 ZD352 R373 R374 Q361 D368 D367 C384 POWER PWB-B3@@ 3 2 1 D364 R387 R384 C372 C368 C373 12 C370 R395 C374 C371 CF351 C356 BF351 11 10 K951 R359 1 2 3 R372 AC POWER SUPPRY CORD AC 230V,50Hz D352 C375 R386 Q360 R371 C395 L352 C391 D363 K952 R385 CNP303 TO MAIN PWB CNP402 P17 9 - A 1 2 3 4 5 6 7 8 9 10 B C E Q354 E C B Q353 E C B R382 T.F R367 ZD351 R392 C390 R383 R370 R375 1 T351 POWER TRANSFOMER TO MAIN PWB CNP901 P17 11 - G C397 T961 6 5 4 3 2 1 C388 CNP901 WH GY WH GY WH RD R391 6 R308 F962 T2.5A L 250V 11 12 CD-C410H,CP-C410 A R1 1K C24 1/50 1 2 3 4 5 6 7 8 CNP2 TR_ 1 TR+ 2 FO+ 3 FO_ 4 GND 5 PD 6 VR 7 LD 8 FE1 10 11 12 13 14 15 C33 0.001 + + 38 HFL 37 TES 36 TOFF 35 TGL 34 SL+ R34 1K 33 29 30 31 32 C53 220P R24 C18 10K 1/50 C19 47/10 R25 1.2K C31 0.0027 + SLOF SLOF SLD REF SLEO SPO C16 0.001 39 SLOF R27 220K C20 0.0033 R26 220K R16 1.5K 27 28 40 CV– JP+ R22 6.8K C14 0.01 SP– 24 25 26 R20 10K 20 21 22 23 SPG – VREF 1 2 3 4 5 6 7 8 9 R41 4.7K C45 4.7/25 CL CLK DEF CE DAT FSS DRF VCC2 VR REF1 – CV+ +B R61 15K C21 1/50 R10 82K D2 1SS119 36 35 34 33 32 +5V 31 30 29 28 27 26 25 R31 10K 24 23 22 16 21 17 20 18 19 +B 6 5 4 3 2 1 CNP3 SP+ SP_ SL+ SL_ PU-IN R54 1K PUIN 1 2 3 4 H • NOTES ON SCHEMATIC DIAGRAM can be found on page 12. 1 2 R49 100K C46 0.022 DRF 6 5 4 3 2 1 SL– SL+ 6 5 4 3 2 1 CNS3A CNS3B M + – SLOF REF R21 56K FE 18 19 FE– FA– FA 17 R32 56K 41 +B CD MOTOR PWB-B + – OR + – +– 42 C32 27P R35 470 R30 15K F G +– + – REF R33 5.6K JP– SL– REF REF R37 47K 43 + REF C17 0.47/50 C44 100/10 M RF RFSM R36 47K R38 33K R70 1K R71 1K R72 1K 1 2 3 4 5 6 7 8 TR_ TR+ FO+ FO_ GND PD VR LD PUCKUP IN SW4 + – R23 1.2K TO FSC FOSTA GEN REF JP REF TO GEN SPI TD + – REF JP GEN TD– C34 0.033 3 4 Figure 20 SCHEMATIC DIAGRAM (1/10) – 20 – 5 6 SQOUT COIN CQCK CNS2A REF JP JPCLO R15 47K E SLIDE M2 FSTA 44 – JP+ R29 1K +B CNS2B CV– + –+ C13 R12 0.1 15K PICKUP UNIT SPIN M1 RFS– C11 0.1 C94 0.001 ACTUATOR SLC CV+ S.Q.R REF GL THD TH R13 33K +B 8/12CM SLOF REF R19 39K FO– TGL1 45 – REF + THDL IC5 M56748FP FOCUS/TRACKING SPIN/SLIDE DRIVER TR– LF2 + – FD R39 22K FSTA REF 16 T– T+ F+ F– GND PD VR LD CL + R14 10K 1 2 3 4 5 6 7 8 FO+ LASER SLI REF DRF SCI 15 D CE VCC TESI R28 1K TR+ + – REF 2FREQ C30 2.2P + – SP C10 14 180P + TE REF 13 – C12 330P R17 82K LT0H30P1 R8 12K DGND TOSTA IC1 LA9240M SERVO AMP. – VCR REF TE– FD– A F C K E A B F + – TB C50 0.1 47 46 FSC FOSTA + 5 4 3 2 1 LD GND R11 3.3K HFL + 12 R9 27K – + – AGND 6 7 C5 0.033 8 R4 C6 2.2K 0.033 9 MON K E B REF VCR VCR REF VCR R5 R6 6.8K C7 0.1/50 100 10 R7 C8 C9 1K 0.047 0.068 11 LD BHI F – C4 0.001 +B DEF + + E REF C + – C15 0.0047 R2 100K TBC EFBAL FE1 – – + R3 10K 5 48 REF + 3 4 55 54 53 52 51 50 49 + – – + REF C3 0.1/50 + RF REF 56 JP– 2 FIN1 57 LATOH FIN2 58 + 1 59 – 1 2 3 4 5 – – 1 2 3 4 5 61 60 62 LDS – 1 2 3 4 5 +B – F B A E K VCC1 64 63 CNP1 CNS1A LDO B PHI +B CNS1B R45 1K R46 1K R47 1K R42 560 3.3V C38 0.01 C35 0.1/50 C25 0.01 C37 220/6.3 C40 0.33/50 4V +B C39 0.47/50 – C1 0.01 +B C2 47/10 Q1 R43 KTA1266 GR 12 1.5V 5 6 CD-C410H,CP-C410 MAIN PWB-A1 (1/4) +B +B C56 100P C57 100P C54 100P +B R75 270 C69 220P CD_L 19 18 35 NC 34 TEST4 33 C43 100/10 C58 0.022 DIGITAL OUT 24 25 26 27 28 29 30 31 D5 1SS119 EXTERNAL OUTPUT SERVO COMMAND TES SURR S_MUTE 32 +B +12V REGULATOR +B R86 1K R87 1K R88 1K Q81 KTC3203 Y 4V D2 1SS119 +B +B GND D7 1SS119 HLF IC2 LC78622U SERVO/SIGNAL CONTROL C21 1/50 C70 220P V/P 17 18 19 20 21 22 23 K C59 0.022 D_GND R82 100 L1 0.82µH +4.3V C51 0.022 C52 47/10 4.7V M_12V 5.2V 17 R81 82 +B GND 16 D_GND 15 D_5V CD-LD M– 1 2 3 4 5 6 7 8 9 Q91 2SB561 C +B 11.8V Q93 R96 KRC102 M 10K R95 3 2 2.2K 0V 0V 11.8V 11.8V 1 0V R98 10K C91 47/16 R97 2.2K CD SIGNAL +B +B 1 2 3 4 11 12 CNP10 CNS10 1 1 SOL 2 2 GND(M) 3 3 M+ M– 4 4 5 5 GND(D) 6 6 OPEN CLOSE 7 7 DISC NO. 8 8 GND(D) 9 9 MECHA UP 10 GND(D) 10 DISC_NO/UP/DOWN GND L700 2.2µH CD_OPEN/CLOSE M_GND GND 5 6 7 8 9 10 MOTOR GND SQOUT COIN CQCK RWC WRQ RES DRF PUIN SL– SL+ 4 K C95 0.001 R49 100K D_GND R70 1K R71 1K R72 1K R77 1K R78 1K R79 1K R99 10K C46 0.022 F1 T500mA L 250V +B +5V 13 1 2 MOTOR PWB-D BIM5 NC LOADING MOTOR DRIVER IC91 TA7291S D91 1SS119 CD-LD M+ +5V P24 2 - A TO MAIN SECTION 1BIT DAC 4FS DIGITAL FILTER CLV DIGITAL SERVO 20 R76 270 R73 2.7K 36 LVDD CLV+ CLV_ XL1 FSX SFSY SBCK RWC WRQ COIN SQOUT /CQCK 16M /RES TEST11 /CS PW 37 MUTEL TEST2 C67 10/16 38 LVSS CD_R R74 2.7K 39 P26 1 - G,P23 10 - G TO MAIN SECTION,DISPLAY PWB C53 220P 40 LCHO SYNC-DETECT EFM DEMODULATE SLICE LEVEL CONTROL EFMIN TOFF 16 41 C81 100/10 15 EFMO C2F 14 VSS C92 0.022 C68 10/16 42 RVSS FR DOUT 13 43 RCHO VVDD EMPH 12 44 RVDD CONT5 11 ERROR COERECT FLAG CONTROL CONT4 10 45 MUTER ISET CONT3 R56 1.2K 46 XVDD CONT2 6 7 8 9 47 XOUT VVSS VDD R34 1K 2KX8 RAM PDO VCO OSC CLOCK CONTROL R57 27K X-TAL GENERATOR CONT1 R32 56K R35 470 C42 0.047 C31 0.0027 C32 27P 3 R58 680 4 5 48 XIN PCK C41 0.047 TA1 JP_ R37 47K TEST5 4M TEST1 R18 3.3M R38 33K EFLG SBSY SUB-CODE XVSS FSEQ R33 5.6K 1 2 µ-COM INTERFACE 49 DEF1 JP+ R36 47K 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 TEST3 C50 0.1 C34 0.033 C30 2.2P R60 1K C22 0.01 +B TGL 4.7K C45 4.7/25 +B C55 100P R45 1K R46 1K R47 1K 1 2 3 4 5 6 + – SOLM2 LOCK M3 UP/DOWN LOADING SW1 OPEN CLOSE M SW2 MECH UP SW3 DISC NO CNS5 14 P22 6 - G,P23 8 - G, 9 - G TO DISPLAY PWB • The numbers 1 to 12 are waveform numbers shown in page 30. 7 8 9 10 Figure 21 SCHEMATIC DIAGRAM (2/10) – 21 – 11 12 CD-C410H,CP-C410 C701 0.022 +B FL701 F F P15 P16 P13 P20 P14 P11 P10 P9 P8 P7 P6 5G P5 P4 6G 7G P3 P2 8G P1 P12 P19 P18 P17 1G 2G 3G 4G 9G F F A 1 2 3 4 5 6 7 8 9 C702 220/6.3 NC NC NC NC 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 +B Q701 KRC107 M 2 –24.8V 4.4V 3 1 –24.9V +B B +B R734 10K R751 100K R701 100K +B R732 10K R717 R719 R721 R713 R715 R716 R718 R720 R722 R723 R725 1K 1K 1K 1K 1K 1K 1K 1K 1K 1K 1K R750 100K R730 1K 7G 8G 1G 2G 3G 4G 9G CD T. T OPEN/CLOSE AVSS CD UP/DOWN, DISC NO RESET CD DSP RES CD DSP COIN CD DSP CQCK CD DSP SQOUT T1/T2 CD DSP RWC TAPE REC TAPE BIAS T0 T1 VDD T2 T5 KEY-3 25 KEY-1 27 SET UP 28 SRS ON/OFF 31 XT2 32 NC VSS 33 42 41 CE 37 CD SL+ CD PUIN SYSTEM STOP X1 34 CL 36 XL7 X2 35 R R R R DI 38 POWER TUNER SD REMOCON IC TAPE SOL NC TAPE MOTOR VDD MIC NC T1 RUN PLSE TAPE F.P. TAPE MECHA STOP 66 S10 DISC1 64 63 DISC2 67 S9 DISC3 68 S8 S12 S13 70 S6 DO 39 CD SL– 71 R797 1K AVREF 30 R-CH INPUT 72 S5 T2 RUN PLSE 73 S4 L-CH INPUT 22 23 24 IC701 IX0191AW SYSTEM MICROCOMPUTER 74 S3 65 S11 R740 1K AVDD 29 75 S2 69 S7 R738 1K KEY-2 26 76 S1 S15 C710 1/50 +B 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 77 S0 S14 D 1 2 T6 79 T8 T3 80 T7 78 NC P17 P18 P19 P12 P1 P6 VLOAD P7 P8 P9 P10 P11 P14 T4 1 2 3 4 5 6 7 8 9 6G 5G CD DSP WRQ C R733 10K DRF 40 R705 10K R703 1K R707 10K R724 1K R700 5.6K R731 10K R727 1K R711 10K 29 17 8 7 6 5 4 3 2 1 24 SL– BIM1 SL+ PUIN MECHA STOP SOLENOIDO T1 RUN FOOL PROOF T2 RUN +B GND MOTOR POWER –VP M_12V GND VF2 VF1 C718 0.001 11.7V 2 3 1 M_GND 11 R 1 D702 1SS119 R771 1.2K 30 R603 10K +B 11.7V C717 0.022 R743 10K C706 47/16 11.7V Q705 KTA1273 Y R758 Q706 10 2SB561 C (1/2W) 0V R760 10K D709 1SS119 D708 1SS119 0V F 28 R704 2.2K 11.7V R759 10K R709 1K +B +B E R702 2.2K R714 1K R712 1K R708 1K R706 1K P13 P16 P15 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 P20 C711 1/50 P21 8 - H TO CD SECTION CNSM1 P26 1 - G,P25 11 - D TO POWER SECTION, MAIN SECTION 1 2 3 4 5 6 7 8 9 G 1 2 3 4 5 6 7 8 9 10 10 11 11 12 12 P25 CNPM1 MOTOR PHM1 RUN PUL SENSO GND +B T2 RUNPULSE FOOL PROOF T1 RUNPULSE SOLENOID MECHA STOP TAPE MEC PW H • NOTES ON SCHEMATIC DIAGRAM can be found on page 12. 1 2 3 4 Figure 22 SCHEMATIC DIAGRAM (3/10) – 22 – 5 6 CD-C410H,CP-C410 DISPLAY PWB-A2 +B +B R734 10K R751 100K R741 10K R757 100K CD T. T OPEN/CLOSE AVSS CD UP/DOWN, DISC NO R749 100 KEY-3 25 KEY-1 27 R740 1K R-CH INPUT CD PUIN X1 34 CL 36 42 41 CE 37 R745 R746 R747 R748 R755 8.2K R783 3.9K R788 5.6K R789 2.2K R775 1.8K R792 3.9K R793 5.6K R794 12K DO 39 DRF 40 1K 1K 1K 1K +B +B 1 2 3 4 5 6 7 8 9 4 39 34 33 35 32 31 14 13 10 CNPM1 MOTOR PHM1 RUN PULSE SENSOR GND +B T2 RUNPULSE 4 2 3 5 6 7 8 9 37 38 36 P21 8 - H,P27 9 - B P24 2 - E TO CD SECTION, TO MAIN MAIN SECTION SECTION + 1 – 2 M 0.2V R785 100 RX701 1V R786 1K R776 0.2V Q709 82 KTC3199 GR 1 2 3 +B D706 1SS119 0.2V R780 10K R798 150 C709 100/6.3 R772 100K D705 C715 220/6.3 1SS119 C708 0.01 D704 ZD701 1SS119 +B MTZJ3.3B R779 R799 1K 12 0.2V 1 0V 4.4V 0V Q708 KTC3199 GR R781 10K R795 2.2K GND D_5V +B 16 15 D_GND R_CHECK L_CHECK DISC_NO/UP/DOWN CD_OPEN/CLOSE RES SQOUT COIN CQCK RWC WRQ T1_T2 REC BIAS SD DRF DO DI CE CL SL+ PUIN SL– CNSM1 40 P25 5 - A,P21 8 - H,P24 2 - B TO CD SECTION, MAIN SECTION 2 C707 3.3/50 D703 1SS119 C705 0.01 R700 5.6K R731 10K R762 1K R724 1K R727 1K C718 0.001 2 3 1 P21 8 - H TO CD SECTION Q707 KRC102 M 4.4V 3 R761 1K +B R705 10K RESET R726 10K R707 10K R703 1K R709 1K R766 3.3K POWER DI 38 M1 12 R769 1.2K R778 2.2K SW712 SW713 SW714 SW715 PLAY DOWN TUNING TUNING UP DOWN C703 15P (CH) C704 18P (CH) XL701 X2 35 CD SL– TUNER SD R744 8.2K XT2 32 NC VSS 33 +B L701 2.2µH 10 R774 1.8K R753 3.3K +B +B 11 R768 1.2K SRS ON/OFF 31 CD SL+ L-CH INPUT T2 RUN PLSE SYSTEM STOP R797 1K AVREF 30 47 46 45 44 43 42 41 1 2 3 4 5 6 7 8 9 R782 3.9K SW717 SW718 SW719 SW721 SW722 SW723 SW724 SW725 TUNER TAPE VIDEO/ CD POWER CLOCK TIMER MEMORY AUX /BAND SET UP 28 AVDD 29 R777 2.2K R773 1.8K SW710 SW711 UP STOP R765 1K R739 1K KEY-2 26 22 23 24 REMOCON R742 10K R738 1K R764 1K SW709 REC PAUSE D701 1SS119 CD DSP RES 18 19 20 21 22 23 24 R752 8.2K R730 1K R733 10K R767 1.2K SW701 SW702 SW703 SW704 SW705 SW706 RANDOM VOLUME X-BASS VOLUME OPEN DISK /DEMO DOWN UP /CLOSE SKIP +B R732 10K R723 1K R725 1K R756 100K R736 100 R750 100K R754 3.3K R737 10K R763 1K P21 12 - E,P26 1 - G TO CD SECTION, POWER SECTION MM1 TAPE MOTOR FWM1 1 FOOL PROOF SWM3 F. P. CNPM2 SWM4 F. A. S T1 RUNPULSE 10 SOLENOID 11 MECHA STOP 12 SOLM1 SOLENOID SWM5 CAM FWM2 TAPE MECHANISM PWB-C 7 8 9 10 Figure 23 SCHEMATIC DIAGRAM (4/10) – 23 – 11 12 CD-C410H,CP-C410 R422 R420 1K 1K C404 0.047(ML) C A_GND 22 C418 0.18(ML) C420 0.068(ML) C422 0.18(ML) C424 0.18(ML) C426 0.033 C428 0.0039 RF4C2 RF4C3 LF4C1 LF4C2 LF4C3 3 2 1 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 R411 22K C445 0.022 RTIN RF1C1 RF1C2 RF1C3 RF2C1 RF2C2 RF2C3 RF3C1 RF3C2 RF3C3 RF4C1 IC401 LC75394E AUDIO PROCES RVref 50 RINVIN2 51 RTOUT 52 RVRIN 53 RTEST 54 RVROUT 55 Vref 56 VDD 57 LVROUT 58 LTEST 59 LVRIN 60 LTOUT 61 LINVIN2 62 LVref 63 LFS 64 C438 100P C440 10/16 C443 22/16 C442 1/50 D 1S C444 100/16 C441 1/50 C439 10/16 C437 100P C435 C433 22/16 0.0027 R479 100K NC NC NC R417 1K C405 0.047(ML) C409 R421 0.047 1K (ML) TO TUNER GND 47 48 C434 0.0027 C436 RFS 49 22/16 C452 2.2/50 C417 0.18(ML) C419 0.068(ML) C421 0.18(ML) C423 0.18(ML) C425 0.033 C427 0.0039 C455 0.0022 R405 39K R3 NC R2 NC R1 AVSS VSS CE DI CL VSS L1 NC L2 NC L3 TAPE_R TAPE_L R406 39K R-CH VIDEO/ AUX. L-CH R415 1K R419 1K C408 390P R407 1.5K SO401 CE DI CL 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 R416 1K R402 1K R401 1K C401 0.047(ML) C407 390P 33 34 35 P23 8 - G TO DISPLAY PWB R408 1.5K B R480 100K 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 R418 1K C406 0.047(ML) C403 0.047(ML) R403 1K OUT_R NC NC NC C402 0.047 (ML) CD_L R4 RINVIN1 RSEL0 18 C410 0.047 (ML) GND L4 LINVIN1 LSEL0 LTIN LF1C1 LF1C2 LF1C3 LF2C1 LF2C2 LF2C3 LF3C1 LF3C2 LF3C3 A_GND 22 C413 100P P21 12 - C TO CD SECTION C412 22/25 R414 3.3K R412 22K C414 100P A OUT_R CD_R C411 22/25 R413 3.3K 20 OUT_L REC_R GND GND D403 1SS119 D L105 1.5µH BIAS Q103 2SC2389 SS 0V R103 2.2K 0.7V + 2 C111 330P R117 1K Q107 KTC3199 GR Q105~Q108: SWITCHING L107 2.2µH C115 47/10 C117 0.018 R119 56 112K 3 4 6 C121 1/50 C127 0.022 R125 5.6K C119 C124 560P 0.015 R131 4.7K 7 8 H • NOTES ON SCHEMATIC DIAGRAM can be found on page 12. 2 3 4 Figure 24 SCHEMATIC DIAGRAM (5/10) – 24 – 5 9 C135 0.068 R111 10K 1 C142 1/50 R146 C145 10K – 5 C113 330P 16 56K Hich=CHROME + 56K C128 3.3/25 1 17 – Hich=T1 + – C136 0.068 C132 0.001 18 R150 10K R140 560 19 6 15 Nor/ CrO2 20 C133 22/16 R141 56 R118 1K 112K ALC 21 – + C131 0.001 R122 100K R124 3.9K 22 R142 56 C134 22/16 10 C141 1/50 C148 0.7V 23 C122 1/50 R15 10 C140 0.0033 R145 10K 0V 0V 24 C130 470P R138 6.8K R126 5.6K KTC 0.7V 0V R136 3.3K R137 6.8K Q105 2SC2389 SS Q108 KTC3199 GR R108 10K Q106 2SC2389 SS 0V 0V 0V R104 2.2K 0V 0.7V C123 0.015 C118 0.018 C116 47/10 L108 2.2µH C114 330P MUTING Q122 KTC3199 GR R154 0V 10K C129 470P R139 560 CNP102 0V C107 0.001 TAPE2 RECORD/ PLAYBACK HEAD 1 2 3 4 5 6 7 8 R106 3.3K R110 10K M_GND ERASE TAPE2_R2 A_GND TAPE2_R1 TAPE2_L1 A_GND TAPE2_L2 0.7V 0V 0V R109 10K L-CH 1 2 3 4 5 6 7 8 Q104 2SC2389 SS C106 180P 0V G CNS102 0V R105 3.3K R-CH C101 0.001 C105 180P ERASE HEAD R120 56 R101 1K C108 0.001 0V L-CH R102 1K 0V CNP101 TAPE1_R 1 A_GND 2 TAPE1_L 3 R107 10K 1 2 3 C102 0.001 CNS101 R112 10K R134 68K R135 3.3K Q111 KRC104 M R133 22K R132 4.7K TAPE1 PLAYBACK HEAD F 3.6V 0V 8.7V REC +B R174 C153 150 100/16 C112 330P NC Q110 Q109~Q111: SWITCHING KRC104 M +B C109 R114 0.047 10K 3 2 R113 0V 10K 0V 1 9.4V R115 Q109 0V 10K 2 1 3 KTA1266 GR 9.4V NC REC C120 560P 38 T1_T2 R121 100K R123 3.9K 37 E 3.6V P23 9 - G TO DISPLAY PWB R-CH R476 100K TAPE_R 36 C139 0.0033 CD-C410H,CP-C410 R R477 2.7K OUT_R MAIN_L GND MAIN_R 21 22 P26 1 - B TO POWER SECTION A_GND 23 R478 2.7K C445 0.022 CNP402 R480 100K C434 0027 C436 22/16 C438 100P C440 10/16 C443 22/16 C442 1/50 1 2 3 4 5 6 7 8 9 D402 1SS119 C444 100/16 C439 10/16 C437 100P +B D401 1SS119 C441 1/50 10 C435 433 22/16 0027 33 SD CL DI DE 39 DO 16 D_GND 11 27 M_GND 40 R479 100K 35 34 C452 2.2/50 TUN_R TUN_L A_GND A–12V D_GND SD DO CL DI CE TO TUNER PWB CNP303 P28 5 - A TO DISPLAY SECTION P23 8 - G T_L C451 2.2/50 GND REC_L C446 0.022 D403 D404 1SS119 1SS119 GND GND A_12V +B R476 100K R475 100K TAPE_L C135 0.068 7 C146 220/10 11 12 R145 10K 11.7V PLAYBACK AND RECORD / PLAYBACK AMP. Vcc 10 C141 1/50 C148 0.082 9 C133 22/16 R141 56 C131 0.001 8 C129 470P R139 560 R137 6.8K R135 3.3K 7 2 C128 3.3/25 – 7 13 IC101 AN7345K Hich=CHROME + 56K 6 14 RIPPLE 56K 11.7V +B 15 R162 4.7K Q126 KRC104 M BIAS GND C142 1/50 R146 C145 10K 22/16 C147 0.022 R150 10K 16 R158 470 0V 2 R164 4.7K 11.6V GND + CD SIGNAL 0V 1 ALC – RECORD SIGNAL 0V R152 1K 17 Nor/ CrO2 18 19 R142 56 C134 22/16 0V 3 C136 0.068 C132 0.001 C130 470P R138 6.8K R172 1K 0.6V R153 10K C140 0.0033 R136 3.3K PLAYBACK SIGNAL MUTING Q121 KTC3199 GR 0.7V 0V FM SIGNAL +B C139 0.0033 0V R167 100K R166 47K SWITCHING Q124 2SA1015 GR R160 150 (1/2W) 0V 0V C150 0.0039 (ML) C151 0.027 (ML) 8 BIAS OSC. Q128 KTC3203 Y 0V C152 47/10 L104 R168 330µH 12 MUTING Q122 KTC3199 GR R154 0V 10K ALC R140 560 REC R134 68K A_12V P22 2 - G,P26 1 - G TO DISPLAY PWB,POWE SECTION REC_R MAIN PWB-A1 (2/4) 9 10 Figure 25 SCHEMATIC DIAGRAM (6/10) – 25 – 11 12 CD-C410H,CP-C410 A MAIN PWB-A1 (3/4) – + + – IC801 LA4451 POWER AMP. B 23 R806 1K C830 47/50 C829 47/50 R805 1K C803 0.0015 R803 3.3K C804 0.0015 R804 3.3K C831 0.001 C827 100/50 R807 180 C C810 1000/25 C801 0.1 C806 1/50 C855 560P C809 1000/25 C828 100/50 22 MAIN_L A_GND MAIN_R C808 47/50 21 9 8 7 6 5 4 3 2 1 C805 1/50 R815 10K P25 1 - A TO MAIN SECTION 14 13 12 11 10 C802 0.1 +B C824 0.022 R808 180 R812 270 (1/2) C812 0.1 (ML) C811 0.1 (ML) C814 0.1 (ML) C813 0.1 (ML) R809 4.7 R810 4.7 TO CD G R811 270 (1/2) L832 0.29µH +B VOLTAGE REGULATOR Q941 2SD2012 Y +B 12.42V D941 1SS119 +B +B C846 0.022 R982 2.2 C850 0.047 +B 19.3V 11.84V VOLTAGE REGULATOR Q942 2SD2012 Y C82 0.0 R825 10K +B 19.1V 11.7V E C848 0.022 D C852 0.047 R844 18 C823 100/50 C825 2200/35 R943 18 Q943 KTC3199 GR D966 D968 D967 +B R946 R947 100 270 D961 RL104A G 19.1V 5.1V M_GND +B 27 16 28 29 30 C954 10/50 D_GND VF1 –VP VF2 5.7V 19.1V Q953 5.7V KTC3199 GR 6.32V C953 0.01 C952 47/16 R952 R951 1.5K 33K R974 12K C957 0.022 ZD951 MTZJ6.2C C976 100/35 11 D_5V ZD972 MTZJ6.2A R975 220 R976 220 • NOTES ON SCHEMATIC DIAGRAM can be found on page 12. 2 3 4 Figure 26 SCHEMATIC DIAGRAM (7/10) – 26 – 5 C974 47/50 R973 100 –28.7V –36V Q971 KTA1266 G VOLTAGE REGULATO H 1 C972 C961 0.047 (ML) C973 47/50 +B C944 4700/25 17 +B C96 0.04 (ML D962 RL104A D964 RL104A Q952 2SD2012 Y +B D951 1SS119 15 Q952, Q953: VOLTAGE LEGULATOR R953 10K P22 2 - G,P23 10 - G,P21 12 - E TO DISPLAY PWB, CD SECTION F POWER C956 0.22 (ML) C943 470/25 D963 RL104A 24 C955 0.22 (ML) C975 47/50 R945 33K C942 100/16 D965 –28V 19.3V 13.1V ZD941 MTZJ13A D942 1SS119 C945 0.022 R949 22K R948 22K C948 10/50 R944 18 12.5V A_12V M_12V C947 10/50 C941 0.022 D965~D968: IN5402M 12.37V 6 CD-C410H,CP-C410 1 51 L_CHECK R_CHECK ER AMP. C453 1/50 C855 560P 9 0/25 31 32 P23 9 - G TO MAIN SECTION C454 1/50 TO CD GND FM SIGNAL R812 270 (1/2) C811 0.1 (ML) J801 HEADPHONES R835 330(1/2W) R811 270 (1/2) R836 330 (1/2W) C844 L831 0.29µH 220P L832 0.29µH C843 220P HEADPHONES PWB-A3 C872 0.001 C871 R845 0.001 10 C845 0.047 C849 0.022 C847 0.047 C851 0.022 R981 2.2 R843 18 C846 0.022 C848 0.022 R982 2.2 C850 0.047 C852 0.047 R844 18 C813 0.1 (ML) R809 4.7 + – – + SP_L-CH SP_L-CH_GND SO801 FRONT SPEAKERS SP_R-CH_GND SP_R-CH C820 0.001 POWER TRANS FORMER T961 D971 RL104A C972 100/50 CNS901 BI901 F962 T2.5A L 250V AC POWER SUPPLY CORD(216) AC 230V 50Hz F963 T1.6A L 250V C971 100/50 –28.7V –36V R972 3.3K R977 2.2 Q971 KTA1266 GR VOLTAGE REGULATOR 7 1 2 3 4 5 6 T. F. ZD971 MTZJ3B C974 47/50 C975 47/50 R976 220 1 2 3 4 5 6 D973 RL104A R973 100 –28V C976 100/35 C961 0.047 (ML) C973 47/50 ZD972 MTZJ6.2A 75 20 C962 0.047 (ML) D962 RL104A D964 RL104A C944 4700/25 D967 D961 RL104A D963 RL104A 1 2 3 4 5 6 C956 0.22 (ML) D972 RL104A D968 R974 12K C955 0.22 (ML) D966 D965 CNP901 D965~D968: IN5402M R978 2.2 POWER PWB-B3 8 9 POWER PWB-B2 10 Figure 27 SCHEMATIC DIAGRAM (8/10) – 27 – 11 12 SO301 ANTENNA TERMINAL 2 1 D362 1SS119 C328 0.001 C323 0.022 5 AM SIGNAL FM SIGNAL D361 1SS119 8 7 6 5 4 3 2 1 R310 4.7K R399 330 R318 470 C331 0.047 FE301 C322 0.022 L311 BALUN VT F OUT GND IF OUT C320 0.022 ANT GND GND VCC R315 82 L312 2.2µH C321 0.022 3 R305 6.8K R320 10K T302 AM ANT. R307 330 NC CF301 2 1 C334 6.8P (UJ) TP301 R304 680 R323 100K R387 22K H:33 N,W,T:56 2 1 Q301 2SC380O CF302 AM LOOP ANTENNA D311 1SS119 R308 33 3 FM MUTE LEVEL Q360 KTA1266GR R386 47K CNP301 C342 0.022 R351 5.6K ZD352 MTZJ3.9B D364 1SS119 3 C397 220P 1 2 T351 AM IF 20 19 18 21 24 23 22 C352 10 C393 1 3 2 1 3 4 5 6 7 8 R377 1K L351 100µH 2 3 4 5 6 7 8 9 1 TP302 R330 L354 2.7K C367 1 C366 0.001 19 18 17 16 15 14 13 12 R381 R380 10K 1.5K 22 21 20 2 Q361 KRC107M C390 470P 1 C382 15P R384 (CH) 12K L353 1mH R358 8.2K VR351 10K(B) IC303 LA1832 X IN X OUT C325 33P C391 R385 10K 47 C362 3.3 AOUT R383 C381 5.6K 12P (CH) X352 AM OSC OUT FM IF IN AM OSC IN AM MIX OUT C350 0.022 C394 47 VSS R382 150 C341 0.022 CE NC C332 0.022 AIN DI D312 1SS119 PD CL C351 0.022 C361 0.022 FM AFC DO VDD R376 1K 10 11 9 17 16 15 14 R395 5.6K R359 1.8K 13 C371 R361 1 4.7K R364 1.8K C372 R362 1 4.7K R360 4.7K C386 330P R398 1.2K C358 1 12 C357 R355 2.2 3.3K 10 11 MPX IN C364 22 AM RF IN VSM REG R379 2.2K 1K 1K 1K 1K MPX VCO C363 0.022 FM/AM OUT AM IF IN AM LOW CUT BF351 C383 0.022 BO1 FM IN C327 0.001 R366 10K Q354 KTC3199GR ZD351 MTZJ5.1B D368 1SS119 D367 1SS199 C384 0.001 L352 100µH C370 1 R354 3.9K R365 10K C375 3.3 R368 33K R367 1K Q353 KTC3199GR R363 1.8K TUN_R SD D_GND R391 390 R392 A_GND 390 TUN_L CNP303 10 1 2 3 4 5 6 7 8 9 TUN_R TUN_L A_GND A_12V D_GND SD DO CL DI CE TO MAIN PWB CNP402 P25 11 - B A R374 R373 R372 R371 D363 1SS119 NC FM DET C368 R356 1K 1 IF OUT C365 0.022 C385 0.01 C392 0.001 SD C353 0.022 C388 10 STEREO C354 0.022 GND R352 1K BO2 AM IN 4 BO3 CF351 R353 270 C399 10.7MHz 0.022 C387 0.022 – 28 – IC302 LC72131 3 BO4 IO2 Figure 28 SCHEMATIC DIAGRAM (9/10) IO1 IF IN X351 VCC R331 470K C374 0.022 C373 0.022 L-CH OUT 2 R-CH OUT 1 PHASE F C398 C356 100 0.001 E (FM/AM) (ST/MONO//STOP) PHASE PILOT D C395 0.022 C396 100 G D352 1SS119 C C355 22P B TUNER PWB-B1 CD-C410H,CP-C410 H • NOTES ON SCHEMATIC DIAGRAM can be found on page 12. 6 CD-C410H,CP-C410 IC1 PIN VOLTAGE NO. 1 2V 2 2V 3 2.1V 4 2.1V 5 2V 6 2V 7 2V 8 2V 9 2V 10 2V 11 2V 12 2V 13 2V 14 2V 15 2V 16 2V 17 2V 18 2V 19 2V 20 2V 21 2V 22 0V 23 2V 24 2V 25 2V 26 2V 27 2V 28 2V 29 2V 30 1.8V 31 1.8V 32 0V 33 0V 34 4V 35 4V 36 0V 37 0V 38 4V 39 0V 40 0V 41 0.3V 42 2V 43 2.1V 44 2.1V 45 0V 46 2V 47 2V 48 0V 49 0V 50 2V 51 4V 52 4V 53 0V 54 4V 55 4V 56 4V 57 2.1V 58 2.1V 59 0V 60 0V 61 2V 62 3.4V 63 0V 64 4V 7 IC2 PIN VOLTAGE NO. 1 0V 2 0V 3 0V 4 0V 5 1.8V 6 4V 7 0V 8 0V 9 2V 10 2V 11 0V 12 0V 13 0V 14 4V 15 0V 16 0V 17 4V 18 4V 19 0V 20 0V 21 2V 22 0V 23 4V 24 0V 25 0V 26 0V 27 0V 28 0V 29 0V 30 4V 31 2V 32 0V 33 0V 34 0V 35 4V 36 3.8V 37 1.7V 38 0V 39 0V 40 1.7V 41 4V 42 4V 43 4V 44 1.8V 45 1.7V 46 0V 47 0V 48 1.8V 49 0V 50 2V 51 0V 52 2V 53 0V 54 0V 55 0V 56 4.4V 57 4.4V 58 4.4V 59 0V 60 1.6V 61 2V 62 0V 63 0V 64 0V 8 IC5 PIN VOLTAGE NO. 1 2V 2 2V 3 0V 4 2V 5 2V 6 2.2V 7 2.2V 8 0V 9 0V 10 0V 11 0V 12 0V 13 2.2V 14 0V 15 2V 16 0V 17 0V 18 0V 19 0.7V 20 5.2V 21 2V 22 2V 23 2V 24 2V 25 2.2V 26 0V 27 0V 28 0V 29 0V 30 2.2V 31 2.2V 32 2V 33 2V 34 0V 35 0V 36 0V IC91 PIN VOLTAGE NO. 1 0V 2 5.1V 3 0.1V 4 0V 5 0V 6 5.1V 7 0V 8 4.2V 9 0V IC101 PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 IC302 PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 VOLTAGE 1.2V(1.2V) 0V(0V) 0V(0V) 4.6V(4.6V) 0V(0V) 4.5V(4.5V) 0.4V(11.3V) 0V(0V) 0V(0V) 1.1V(0V) 5.5V(5.5V) 0V(0V) 0.5V(0.1V) 0V(0V) 0V(2.6V) 1.5V(0V) 5.6V(5.3V) 1.2V(1V) 1.2V(1V) 3.8V(1.2V) 0V(0V) 2.8V(2.6V) IC303 PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 VOLTAGE 2V(2V) 2V(2V) 7.2V(8.2V) 0.5V(0.8V) 2V(2V) 0V(0V) 5.5V(5.5V) 0V(0V) 2.6V(2.6V) 2.6V(2.6V) 6.3V(8.2V) 1.2V(1.2V) 1.4V(0V) 2.2V(2V) 1.3V(1.4V) 2V(1.9V) 2V(2V) 1.6V(1.6V) 0.6V(0.7V) 7.2V(8.2V) 7.2V(8.2V) 2V(2V) 2V(2V) 2V(2V) VOLTAGE 0V 0V 0.6V 3V 0V 1.3V 0V 0.6V 3V 3V 0V 0V 6V 3.7V 0V 3V 0.6V 0V 0.8V 0V 3V 0.6V 0V 0V 9 IC401 PIN VOLTAGE NO. 1 5V 2 5V 3 5V 4 5V 5 5V 6 5V 7 5V 8 5V 9 5V 10 5V 11 5V 12 5V 13 5V 14 5V 15 5.1V 16 4.7V 17 4.7V 18 0V 19 4.7V 20 0V 21 4.7V 22 0V 23 0V 24 4.4V 25 0V 26 0V 27 0V 28 4.7V 29 0V 30 4.7V 31 0V 32 4.7V 33 4.7V 34 5.1V 35 5.1V 36 5.1V 37 5.1V 38 5.1V 39 5.1V 40 5.1V 41 5.1V 42 5.1V 43 5.1V 44 5.1V 45 5.1V 46 5.1V 47 5.1V 48 5V 49 5.1V 50 5.1V 51 5.1V 52 5.1V 53 5.1V 54 0V 55 5.1V 56 5.1V 57 10.2V 58 5.1V 59 0V 60 5.1V 61 5.1V 62 5.1V 63 5.1V 64 5.1V 10 Figure 29 SCHEMATIC DIAGRAM (10/10) – 29 – 11 IC701 PIN VOLTAGE PIN VOLTAGE NO. NO. 1 –24.7V 41 0.41V 2 –24.7V 42 0V –24.7V 3 43 0V –24.7V 4 44 4.4V 5 –24.7V 45 0V 6 –24.7V 46 4.4V 7 –24.7V 47 4.4V 8 4.4V 48 0V 9 0V 49 2.7V 10 4.4V 50 11.7V 11 4.4V 51 11.7V 12 0.24V 52 4.4V 13 0V 53 4.4V 14 4.4V 54 4.4V 15 4.4V 55 0V 16 0.12V 56 0V 17 0V 57 4.4V 18 4.4V 58 0V 19 0V 59 0V 20 0V 60 0V 21 0V 61 –21.2V 22 3.8V 62 –18V 23 0V 63 –11.5V 24 0V 64 –27.8V 25 4.4V 65 –24.5V 26 4.4V 66 –14.8V 27 4.4V 67 –24.5V 28 0.6V 68 –21.2V 29 4.4V 69 –27.8V 30 0V 70 –18V 31 4.4V 71 –28V 32 0V 72 –11.5V 33 2V 73 –24.4V 34 2V 74 –24.4V 35 0V 75 14.7V 36 0V 76 –27.8V 37 0V 77 –24.4V 38 4.4V 78 –27.8V 39 4.4V 79 –27.8V 40 0V 80 –24.8V IC801 PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 VOLTAGE 24.7V 14.19V 0V 0V 14.05V 24.8V 27.8V(C420)/31.8V(C2700) 1.24V 5.3mV 26.7V 0V 2.25V 5.2mV 1.23V 12 CD-C410H,CP-C410 WAVEFORMS OF CD CIRCUIT STOP FOCUS 1 2 PLAY SERCH 5ms 0.50 V IC1 20 F.E 5ms 5.0 V IC1 54 DRF 6 0.5ms 10.0 V JP+ 7 0.5ms 10.0 V JP- 8 0.5ms 0.50 V JP 9 0.5ms 1.00 V TE 3 1 CUE 3 0.5ms 1.00 V HF 4 0.5ms 5.0 V HFL 1 5 0.5ms 5.0 V TES 3 3 0.5ms 1.00 V HF PLAY NORMAL DISC TN0=01 10 20ms 1.00 V SPO 11 20ms 2.00 V CLV+ 2 REVIEW PLAY 4 0.5ms 5.0 V HFL 1 5 0.5ms 5.0 V TES 3 6 50ms 10.0 V JP+ 7 50ms 10.0 V JP- 8 50ms 0.50 V JP 9 50ms 1.00 V TE 6 0.5ms 10.0 V JP+ 7 0.5ms 10.0 V JP- 8 0.5ms 0.50 V JP 9 0.5ms 1.00 V TE 6 50ms 10.0 V JP+ 7 50ms 10.0 V JP- 8 50ms 0.50 V JP 9 50ms 1.00 V TE TCD-712 (140mm) TN0=01 2 10 50ms 1.00 V SPO 11 50ms 2.00 V CLV+ CUE PLAY TCD-712 12 5s 100mV SLD 1 12 0.5s 100mV SLD REVIEW 1 – 30 – CD-C410H,CP-C410 TROUBLESHOOTING (CD SECTION) When the CD does not function When the CD section does not operate When the objective lens of the optical pickup is dirty,this section may not operate.Clean the objective lens,and check the playback operation.When this section does not operate even after the above step is taken,check the following items. Remove the cabinet and follow the troubleshooting instructions. "Track skipping and/or no TOC(Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickup lens. Before attempting any adjustment make certain that the lens is clean. If not, clean it as mentioned below." Turn the power off. Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol. Do not touch the lens with the bare hand. • When the turntable fails to stop. 5V Is from 2.5V 5 V till 2.5V down pulse (approx. 300 ms) 0V No input into the IC701 pin 21 when the turntable is rotating? Check the SWM3 and the wiring from the IC701 pin 21 to the SWM3. Yes Is there following voltage input on the IC701 pin 21 in the specific state? When the CD mechanism is moved up: 0V In other states: 4.3V No Check the MECHA UP SW and the wiring from the IC701 pin 21 to the MECHA UP SW. Yes Check IC2 pin26 Q91 and Q93 and the periphery. Yes IC701 defective. • When turntable fails to move. Is there following voltage input on the IC701 pin 21 in the specific state? When the CD mechanism is moved up: 0V In other states: 4.3V No Check the MECHA UP SW and the wiring from the IC701 pin 21 to the MECHA UP SW. Yes Is L output from the IC2 pin 26 during SEC when the disc skip switch is pressed? Check the wiring of IC2 pin 26 and Q93 pin 2. No OK Yes IC2 defective. Is 4V output from the Q91 emitter during operation stated above? No Yes Check turntable motor and turntable mechanism. – 31 – Check Q91, Q93 and the periphery. CD-C410H,CP-C410 • When the CD tray fails to open or close. Is there following voltage input in specific state of IC701 pin 19? Open state: 0V Close state: 0V Intermediate state between open state and close state: 4.3V Check the OPEN CLOSE SW and the wiring from the IC701 pin 19 to the OPEN CLOSE SW. No Yes Is H output to IC2 pin 24 or 25 for 7 seconds when the OPEN/ CLOSE key is pressed?IC91 is defective. Replace it. Check the wiring of the IC2 pins 24 and 25, IC91 pins 1 and 3. No OK IC2 defective. Yes Is 4V output between IC91 pins 3 and 7 during operation stated above? Check the periphery of IC91. No OK Yes IC91 defective. Check the loading motor (M1) and the loading mechanism. • The CD function will not work. The CD operating keys don't work. Yes Check the CD, DSP, power supply, and 16.93 MHz clock, and reset terminal. Yes Check the waveform of SCK, SO (DATA) and SI (COMM). Yes See if the pick-up is in the pick-up in PICKUP IN SW position. Focus search is performed two times when play operation is done without disc. 0.5s 0.50 V IC1 16 FD Yes If the items mentioned above are OK, check the main microcomputer IC701. • The CD operating keys work. 0.5s 0.50 V IC1 7 TE Check the Focus - HF system. 1 Playback can be performed without a disc. 2 Figure 32 Yes Does the pick-up move up and down twice? Yes Focus search OK No Does the output waveform of IC1(16)(FD) match that shown in Fig. 32? Check the area around IC5-CNP2. Yes No Check the IC1(50)(CLK) line, 4MHz. Check the microcomputer data on pins (51)(CL), (52)(DAT) and (53)CE. – 32 – CD-C410H,CP-C410 • Playback can only be performed when a disc is loaded. Is the Focus servo active? (Can you hear it working?) No Check the laser diode driver. Check the area around IC1(16) - (21) (focus servo circuit). No If the disc is not turning, the DRF should not change to "H". Yes Yes Does the DRF signal change from "L" to "H"? Check the spin system. Yes Yes No Is HF waveform normal (see the Fig.33-1, 2)? Check the periphery of IC1 pins 41 and 42. Level is abnormal. Yes Yes Check the spin system. Waveform is unstable. Check the tracking system. HF 1.0V/DIV 0.5µsec/DIV(DC) (When playing back the disc) Waveform in case of normal play-back 0.5s 1.00 V IC1 16 FD 0.5s 10.0 V IC2 13 CLV+ 2 1 3 0.5s 10.0 V IC1 54 DRF 4 0.5s 2.00 V IC1 7 TE Figure 33-1 Figure 33-2 • Check the tracking system. Check waveform of IC1 pin 7 (TE). The waveform shown in Fig.33-3 appears, and nodisc state appears soon. Play is possible in TEST mode. Yes Yes Tracking servo is inoperative. Yes Although IL is possible, play is impossible. Data cannot be read. Yes Yes Check the periphery of IC 1 pin 8 to pin 15, and IC 5 to CNP2. Normal jump is impeded, and the program top cannot be reached. Check the VCO-PLL system. 5ms 1.00 V IC1 7 TE 4 5 ms 5.0 V IC1 54 DRF 3 Figure 33-3 – 33 – Yes Check the periphery of IC 1 pin 14. CD-C410H,CP-C410 • Checking the spin system. Play operation is performed without disc. Yes Yes The turntable rotates a little. The spin driver circuit is normal. No Yes The turntable fails to rotate or rotates at high speed. Check the periphery of IC1 pins 23 to 27, pin 39, and pin 40, IC2 pin 12 and pin 13, IC5 to CNP3. • Checking the VCO-PLL system Play operation is performed when disc exits. Yes Although HF waveform is normal, TOC data cannot be read. Yes Check PDO waveform (Fig. 34). Abnormal Check the IC1 pins 43 and 44, IC2 pins 3, 5, 7, 10, and 11. Stop --> Play As VCO frequency is locked at 4.32 M Hz, voltage of PDO rises and stabili- zes. 0.5s 1.00 V IC2 3 PDO 2 0.5s 1.00 V IC2 16 FD 3 Figure 34 • Although HF waveform is normal and the time indication is normal, no sound is emitted. No Check IC 2 pin 48 (EFLG). Yes Check IC2 pins 37, 40. Abnomal Check IC 401 and POWER AMP IC 801. – 34 – Usually, the number of pulses of flawless disc is 100 pulses/sec or less. CD-C410H,CP-C410 FUNCTION TABLE OF IC IC2 VHiLC78622U-1:Servo/Signal Control(LC78622U) (1/2) Pin No. Terminal Name Input/Output 1 DEFI 2 TAI 3 PDO Output 4 VVSS — 5 ISET Input 6 VVDD — Power terminal for integrated VCO. 7 FR Input VCO frequency range adjustment. 8 VSS 9 EFMO Output 10 EFMIN Input 11 TEST2 Input 12 CLV+ Outout Output for disk motor control. 3 values can be output with the commands. 13 CLV- Output Output for disk motor control. 3 values can be output with the commands. 14 V/P Output Monitor output terminal for automatic switch of rough servo/phase control. "H" for rough servo, and "L" for phase servo. 15 HFL Intput Input terminal of track detection signal. Schmit input. 16 TES Input Input terminal of tracking error signal. Schmit input. 17 TOFF Output 18 TGL Output Output terminal for switch of tracking gain "L" increases the gain. 19 JP+ Output Output for track jump control. 3 values can be output with the commands. 20 JP- Output Output for track jump control. 3 values can be output with the commands. 21 PCK Output Clock monitor terminal for EFM data replay. 4,3218MHz as the phase clock. 22 FSEQ Output Output terminal synchronous signal detection. "H" is output when synchronous signal detected by EFM signal matches synchronous signal internally generated. 23 VDD 24 CONT1 Input/Output General purpose input/output terminal 1 25 CONT2 Input/Output General purpose input/output terminal 2 26 CONT3 Input/Output General purpose input/output terminal 3 27 CONT4 Input/Output General purpose input/output terminal 4 28 CONT5 Input/Output General purpose input/output terminal 5 29 EMPH Output Difference monitor terminal At "H", deemphasis disk is being replayed. 30 C2F Output C2 flag output terminal. 31 DOUT Output Output terminal of digital OUTPUT. (EIAJ format) 32 TEST3 Input Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V. 33 TEST4 Input Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V. 34 N.C. 35 MUTEL 36 LVDD — 37 LCHO Output 38 LVSS — 39 RVSS — 40 RCH0 Output 41 RVDD — 42 MUTER 43 XVDD — 44 XOUT Output Ground terminal of 16.9344 MHz quartz oscillator. 45 XIN Input Ground terminal of 16.9344 MHz quartz oscillator. 46 XVSS — 47 SBSY Output Output terminal of synchronous signal of subcode block. 48 EFLG Output Correction monitor terminal of C1, C2, single and double. Function Input Input terminal of defect detection signal (DEF). (Connected to OV when not used.) Input For PLL — — — Output Output Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V. Output terminal of phase comparison for external VCO control. Ground terminal for integrated VCO. Surely connected to 0V. Resistance connection terminal for current adjustment of PDO output. Ground terminal of digital system. Surely connected to 0V. For slice level control EFM signal output terminal. EFM signal input terminal. Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V. Tracking OFF output terminal. Power terminal of digital system. Controlled with serial data command from micro computer. When not used, set it as the input terminal and open it by connecting to 0V, or set it as the output terminal and open it. Terminal not used. Open during operation. L channel 1 bit DAC Mute output terminal for L channel. Power terminal for L channel. L channel output terminal. Ground terminal for L channel Surely connected to 0V. R channel 1 bit DAC Ground terminal for R channel Surely connected to 0V. R channel output terminal. Power terminal for R channel. Mute output terminal for R channel. Power terminal for quartz oscillation. Ground terminal for quartz oscillation. Surely connected to 0V. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 35 – CD-C410H,CP-C410 IC2 VHiLC78622U-1:Servo/Signal Control(LC78622U) (2/2) Pin No. Terminal Name Input/Output 49 PW Output Output terminal of subcodes P, A, R, S, T, U and W. 50 SFSY Output Output terminal of synchronous signal of subcode frame. It drops when subcode stands by. 51 SBCK 52 FSX Output Output terminal of synchronous signal of 7.35kHz divided from quartz oscillation. 53 WRQ Output Output terminal to stand by output of subcode Q. 54 RWC 55 SQOUT 56 COIN Input Command input terminal from microcomputer. 57 CQCK Input Clock input terminal to fetch command input, or pick up subcode from SQOUT. Schmit input 58 RES Input 59 TST11 Output Output terminal for test. Used in the open state ("L" output as ordinary). 60 16M Output Output terminal of 16.9344Hz. 61 4.2M Output Output terminal of 4.2336MHz. 62 TEST5 Input Input terminal for test Pull-down resistor is integrated. Surely connected to 0V. 63 CS Input Chip selection input terminal. Pull-down resistor is integrated. Connected to 0when not controlled. 64 TEST1 Input Input terminal for test Pull-down resistor is integrated. Surely connected to 0V. Input Input Output Function Clock input terminal to read subcode. Schmit input (Connected to 0V when not used.) Input terminal of read/write. Schmit input. Output terminal of subcode Q. Reset input terminal of LC78622. When turning on power, set it at "L". Note: The same potential must be supplied to the power terminals (VDD, VVDD, LVDD, RVDD, XVDD). DEFI Slice level control EFMIN FSEQ Vss VDD TAI TSTI1 TEST1 TEST2 TEST3 TEST4 TEST5 PCK FR I SET PDO VVDD VVss EFMO In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. RAM address generator 2K X 8bit RAM VCO colck oscillation clock control Sync detection EFM demodulation Interpolation mute C2F Bilingual Digital OUT CLV+ CLV- CLV Digital servo Flag processing of C1/C2 error detection and correction DOUT Digital attenuator V/P PW SBCK SBSY SFSY CS Subcode division QCRC WRQ SQOUT X4 oversampling digital filter (NC) µCOM Interface 1bitDAC CQCK Figure 36 BLOCK DIAGRAM OF IC – 36 – LCHO MUTEL LVss LVDD RCHO RVss RVDD MUTER EFLG EMPH CONT1 CONT2 CONT3 CONT4 CONT5 TGL RES JP- JP+ TOFF HFL RWC TES L.P.F XTAL system timing generator General-use port Servo commander 16M 4.2M XVss FSX XIN XOUT XVDD COIN CD-C410H,CP-C410 IC1 VHiLA9240M/-1:Servo Amp.,(LA9240M) (1/2) Pin No. Function Port Name 1 FIN2 Connection pin for photodiode of pickup. RF signal is generated through addition with FIN pin, and FE signal is generated through subtraction. 2 FIN1 Connection pin for photodiode of pickup. 3 E Connection pin for photodiode of pickup. TE signal is generated through subtraction with F pin. 4 F Connection pin for photodiode of pickup. 5 TB Pin for input of DC component of TE signal. 6 TE- Pin to connect gain setting resistor of TE signal to TE signal. 7 TE TE signal output pin. 8 TESI TES (Track error sense) comparator input pin. TE signal is band-passed and input. 9 SCI Input pin for shock detection. 10 TH Pin to set time constant of tracking gain. 11 TA TA amplifier output pin. 12 TD- Pin to compose tracking phase compensation constant between TD and VR pins. 13 TD Pin to set tracking phase compensation. 14 JP Pin to set amplitude of tracking jump signal (kick pulse). 15 TO Tracking control signal output pin. 16 FD Focusing control signal output pin. 17 FD- Pin to compose focusing phase compensation constant between FD and FA pins. 18 FA Pin to compose focusing phase compensation constant between FD-/FA-pins. 19 FA- Pin to compose focusing phase compensation constant between FA and FE pins. 20 FE Output pin of FE signal. 21 FE- Pin to connect gain setting resistor of FE signal across TE pin. 22 AGND GND for analog signal. 23 SP Single end output for CV+ and CV- pin input. 24 SPI Spindle amplifier input. 25 SPG Pin to connect gain setting resistor in the 12cm mode of spindle. 26 SP- Pin to connect spindle phase compensation constant together with SPD pin. 27 SPD Spindle control signal output pin. 28 SLEQ Pin to connect thread phase compensation constant. 29 SLD Thread control signal output pin. 30 SL- Input pin of thread feed signal from micro computer. 31 SL+ Input pin of thread feed signal from micro computer. 32 JP- Input pin of tracking jump signal from DSP. 33 JP+ Input pin of tracking jump signal from DSP. 34 TGL Input pin of tracking gain control signal from DSP. TGL = Gain low at "H" 35 TOFF Input pin of tracking off control signal from DSP. TOFF = Off at "H" 36 TES Output pin of TES signal to DSP. 37 HFL (HIGH FREQUENCY LEVEL) is used to judge whether main beam is positioned on the bit or on the mirror. 38 SLOF Thread servo off control input pin. 39 CV- Pin to input CLV error signal from DSP. 40 CV+ Pin to input CLV error signal from DSP. 41 RFSM RF output pin. 42 RFS- Pin to set gain of RF and set 3T compensation constant together with RFSM pin. 43 SLC (SLICE LEVEL CONTROL) is the output pin to control of the level of the data slice with RF waveform DSP. 44 SLI Input pin to control the level of data slice with DSP. 45 DGND GND pin in the digital system. 46 FSC Output pin for focus search smoothening capacitor. 47 TBC (Tracking Balance Control) Pin to set EF balance variable range. 48 NC No connect. 49 DEF Defect detection output pin of disk. 50 CLK Reference clock input pin. 4.23MHz of DSP is input. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 37 – CD-C410H,CP-C410 IC1 VHiLA9240M/-1:Servo Amp.,(LA9240M) (2/2) Function Port Name Pin No. 51 CL 52 DAT Micro computer command clock input pin. Micro computer command data input pin. 53 CE Micro computer command chip enable input pin. 54 DRF (DETECT RF) RF level detection output. 55 FSS (Focus Serch Select) Pin to switch focus search mode. (± search/+ search for reference voltage) 56 VCC2 VCC pin for servo system and digital system. 57 REFI Pin to connect pass control for reference voltage. 58 VR Reference voltage output pin. 59 LF2 Pin to set defect detection time constant of disk. 60 PH1 Pin to connect capacitor for peak hold of RF signal. 61 BH1 Pin to connect capacitor for bottom hold of RF signal. 62 LDD APC circuit output pin. 63 LDS APC circuit output pin. 64 VCC1 RF system VCC pin. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. LDS 63 VCC1 64 LDD 62 BH1 61 PH1 60 APC FIN2 1 FIN1 2 3 F 4 TB 5 TE- 6 TE 7 TESI 8 SCI 9 VR 58 REFI 57 VCC2 56 FSS DRF CE DAT CL CLK 55 54 53 52 51 50 DEF 49 REF RF DET 48 NC 47 TBC VCA I/V E LP2 59 46 FSC BAL 45 DGND SLC µ-COM VCA INTER FACE 44 SLI 43 SLC 42 RFS- TE 41 RFSM RF AMP 40 CV+ 39 CV- T.SERVO & T.LOGIC 38 SLOF TH 10 37 HFL 36 TES TA 11 35 TOFF 34 TGL TD- 12 F.SERVO & F.LOGIC SPINDLE SERVO 33 JP+ SLED SERVO TD 13 JP 14 TO 15 FD 16 17 FD- 18 FA 19 FA- 20 FE 21 22 23 FE- AGND SP 24 SPI 25 SPG Figure 38 BLOCK DIAGRAM OF IC – 38 – 26 SP- 27 SPD 28 SLEQ 29 SLD 30 31 SL- SL+ 32 JP- CD-C410H,CP-C410 IC701 RH-iX0191AWZZ:System Microcomputer (IX0191AW) (1/2) Pin No. Port Name Terminal Name 1-7 FIP6-0 8 VDD 9 P27 TAPE BIAS Output TAPE BIAS ON: H 10 P26 TAPE REC Output TAPE REC. ON:L 11 P25 T1/T2 Output TAPE2 PLAY:L 12 P24 CD DSP WRQ 13 P23 CD DSP RWC Output CD DSP Read write control 14 SCK1 CD DSP CQCK Output CD DSP Clock 15 SO1 CD DSP COIN Output CD DSP Comand 16 SI1 CD DSP SQOUT 17 RESET RESET 18 P74 CD DSP RES 19 P73 CD T/T OPEN/CLOSE 20 AVSS — 21 ANI7 CD UP/DOWN CD DISC NO 22 ANI6 T2 RUN PLSE Input 23 ANI5 L-CH CHECK Input/Output For TEST mode 24 ANI4 R-CH CHECK Input/Output For TEST mode 25 ANI3 KEY INPUT 3 Input Key input 3 26 ANI2 KEY INPUT 2 Input Key input 2 27 ANI1 KEY INPUT 1 Input Key input 1 28 ANI0 Initial setting input Input Initial setting input 29 AVDD AVDD — Connect with BACK UP VDD 30 AVREF AVREF — Connect with UNBACK UP VDD 31 P04 SRS 32* XT2 — Non connect 33 VSS — Connect with GND 34 X1 X1 Input 35 X2 X2 Output MAIN CLOCK 4.19NHz 36 P37 C2B CL Output C2B Bus clock 37 P36 C2B CE 38 P35 FL DRIVER Function Input/Output Output — Input Segment Output Connect with BACK UP VDD CD DSP Write request Input CD DSP Code Q out Input Reset Input: L Outout Input — Intput Input CD DSP RES interface signal CD Turntable open close Connect with GND CD mecha up/down CD disc no TAPE2 Run pulse SRS provided/not provided MAIN CLOCK 4.19MHz Output C2B Bus chip enable 2 Output C2B Bus comand 2 C B DI 39 P34 C B DO Input C2B Bus data 40 P33 CD DRF Input Data read fiug from DSP 41 P32 CD PUIN Input 42 P31 CD SL+ Output CD pickup slide motor control 43 P30 CD SL- Output CD pickup slide motor control 44 P03 POWER Output POWER ON: H 45 P02 TUNER SD Input Tuner SD Signal 46 INPT1 SYSTEM STOP Input System Stop Signal 47 INPT0 REMOCON Input 48 IC INTERNALLY CONECTED — L: Innermost periphery Remote Control Code Input Connect with GND 49* P72 P.B MUTE Output P.B MUTE ON: H 50 P71 TAPE SOL. Output TAPE SOL. ON: L 51 P70 TAPE MOTOR Output TAPE MOTOR ON: L 52 VDD VDD 53 P127 MIC MUTE 54* P126 — 55 P125 TAPE F.P. — Input Output Input Connect with BACK UP VDD MIC MUTE: L CD STOP, TAPE STOP state: Mute cancel Non connect TAPE FOOL PROOF REC: L In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 39 – CD-C410H,CP-C410 IC701 RH-iX0191AWZZ:System Microcomputer (IX0191AW) (2/2) Pin No. Port Name Terminal Name Input/Output 56 57 P124 TAPE1 RUN PULSE Input TAPE1 Run pluse P123 TAPE MECHA STOP Input 58*-60* Tape mecha up state: L P122-P120 DISC1-DISC3 Function Output Non connect 61-70 FIP25-16 FL DRIVER Output Segment output 71 VLOAD VLOAD Output Connect with VPP 72-77 FIP15-FIP10 FL DRIVER Output Segment output 78* P97 — Output Non connect 79,80 FIP8,FIP7 FL DRIVER Output Segment output PB CrO2 In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. FIP21 FIP20 FIP19 FIP18 FIP17 FIP16 V.LOAD FL DRIVER SEGMENT FIP15 FIP14 FIP13 FIP12 FIP11 FL DRIVER SEGMENT FIP10 P97 FIP8 FIP7 FL DRIVER DIGIT FIP4 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 FIP22 63 FIP23 2 62 FIP24 3 FIP3 4 FIP2 5 FIP1 6 FIP0 7 CONNECT WITH VDD VDD 8 TAPE BIAS P27 9 TAPE REC P26 10 T1/T2 P25 11 CD DSP WRQ P24 12 CD DSP RWC P23 13 SCK1 14 SO1 15 SI1 16 FIP6 FIP5 CD DSP CQCK CD DSP COIN CD DSP SQOUT RESET INPUT CD DSP RES 1 61 FIP25 60 P120 µPD78045 DISC 2 57 P123 56 P124 TAPE MECHA STOP 55 P125 54 P126 TAPE F.P. 53 P127 52 VDD MIC MUTE 51 P70 50 P71 TAPE MOTOR 49 P72 48 IC RESET 17 P74 18 DRF P33 C B DO P34 2 C B DI P35 2 C B CE P36 2 C2 B CL MAIN CLOCK GND TERMINAL SRS CONNECT WITH UN BACK UP VDD CONNECT WITH VDD Initial Setting Input P37 41 P32 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 X2 AN14 X1 Rch INPUT Vss 23 XT2 AN15 XT1 22 AVREF AN16 AVDD T2 RUN PLSE Lch INPUT ANI0 21 ANI1 AN17 KEY INPUT 1 P.B MUTE CONNECT WITH GND CD SL- CD UP/DOWN DISC NO KEY INPUT 2 TAPE SOL. 43 P30 42 P31 20 ANI2 CONNECT WITH VDD TUNER SD AVSS ANI3 VOL.0 MUTE 45 P02 44 P03 CONNECT WITH GND KEY INPUT 3 T1 RUN PLSE REMOCON INPUT CD T.T OPEN/CLOSE 19 – 40 – DISC 1 47 INTP0 46 INTP1 P73 Figure 40 BLOCK DIAGRAM OF IC DISC 3 59 P121 58 P122 SYSTEM STOP POWER CD SL+ CD PUIN CD-C410H,CP-C410 Regbase 19 18 Reg5V 20 17 Vcc Vcc Vctl3(+) 21 16 N.C Vctl3(-) 15 Gain2 22 14 Vctl2(-) Vctl3(out) PA 13 VM2(-) 23 25 PA 12 VM2(+) VM3(-) 26 11 24 VM3(+) 27 28 9 10 29 8 GND VM4(+) 30 VM4(-) Vctl4(-) 32 10K 31 Gain4 33 Standby 34 35 15K 3.6K 10.8K OP1 10K PA PA 10K GND 5 Vctl(-) 7 4 Gain1 VM1(+) 3 N.C 6 2 Vrel-out VM1(-) 1 Vrel-in 10K OP1 OP1 10K OP1 TSD Vcc 10K 10K OP1 PA PA PA 10K OP1 PA 23K Stand by 25K 15K 36 Standby SS.GND IC5 VHiM56748FP-1:Focus/Tracking/Spin/Slide Driver (M56748FP) Figure 41-1 BLOCK DIAGRAM OF IC LCD701 : VVKFiP9EM7R-1 1 2 FL Display 3 REC SLEEP X-BASS MEMORY ST WIDE TA SRS kHz DOLBY NR T P MHz Figure 41-2 FL DISPLAY WIRING OF PRIMARILY SUPPLY LEADS (FOR UK ONLY) If any one of the bands shown in Fig. 41-3 is removed for some reason, be sure replace it to the original position and same appearance as before. Nylon Band 80mm 92LN-BAND 1318A Core Power Transformer AC Power Supply Cord Blue Brown Figure 41-3 – 41 – RDS CD-C410H,CP-C410 —MEMO— – 42 – CD-C410H,CP-C410 PARTS GUIDE MODEL CD-C410H CP-C410 “HOW TO ORDER REPLACEMENT PARTS” To have your order filled promptly and correctly, please furnish the following information. 1. MODEL NUMBER 2. REF. No. 3. PART NO. 4. DESCRIPTION For U.S.A. only Contact your nearest SHARP Parts Distributor to order. For location of SHARP Parts Distributor, Please call Toll-Free; 1-800-BE-SHARP MARK: SPARE PARTS-DELIVERY SECTION Explanation of capacitors/resistors parts codes Capacitors Resistors VCC ....................... Ceramic type VCK ........................ Ceramic type VCT ........................ Semiconductor type VC • • MF ............... Cylindrical type (without lead wire) VC • • MN ............... Cylindrical type (without lead wire) VC • • TV ................ Square type (without lead wire) VC • • TQ ............... Square type (without lead wire) VC • • CY ............... Square type (without lead wire) VC • • CZ ................ Square type (without lead wire) VC • • • • • • • • • J .. The 13th character represents capacity difference. ("J" ±5%, "K" ±10%, "M" ±20%, "N" ±30%, "C" ±0.25 pF, "D" ±0.5 pF, "Z" +80-20%.) VRD ....................... Carbon-film type VRS ........................ Carbon-film type VRN ....................... Metal-film type VR • • MF ............... Cylindrical type (without lead wire) VR • • MN ............... Cylindrical type (without lead wire) VR • • TV ................ Square type (without lead wire) VR • • TQ ............... Square type (without lead wire) VR • • CY ............... Square type (without lead wire) VR • • CZ ................ Square type (without lead wire) VR • • • • • • • • • J .. The 13th character represents error. ("J" ±5%, "F" ±1%, "D" ±0.5%.) If there are no indications for the electrolytic capacitors, error is ±20%. If there are no indications for other parts, the resistors are ±5% carbon-film type. NOTE: Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace parts with specified ones for maintaining the safety and performance of the set. – 43 – CD-C410H,CP-C410 NO. PRICE RANK PART CODE DESCRIPTION NO. INTEGRATED CIRCUITS IC1 IC2 IC5 VHILA9240M/-1 VHILC78622U-1 VHIM56748FP-1 J J J IC91 IC101 VHITA7291S/-1 VHIAN7345K/-1 J J IC302 IC303 VHILC72131/-1 VHILA1832//-1 J J IC401 IC701 VHILC75394E-1 RH-IX0191AWZZ J J IC801 VHILA4451//-1 J AV Servo Amp.,LA9240M AT Servo/Signal Control,LC78622U AR Focus/Tracking/Spin/Slide Driver,M56748FP AH Loading Motor Driver, TA7291S AM Playback and Record/ Playback Amp.,AN7345K AP PLL (Tuner),LC72131 AR FM IF Det./FM Mpx./ AM IF, LA1832 AX Audio Processor,LC75394E AZ System Microcomputer, IX0191AW AN Power Amp.,LA4451 VSKTA1266GR-1 VSKTC3203Y/-1 VS2SB561-C/-1 VSKRC102M//-1 VS2SC1845F/-1 VSKTC3199GR-1 VSKTA1266GR-1 VSKRC104M//-1 VSKTC3199GR-1 VS2SA1015GR-1 VSKRC104M//-1 VSKTC3203Y/-1 VS2SC380-O/-1 VSKTC3199GR-1 VSKTA1266GR-1 VSKRC107M//-1 VSKRC107M//-1 VSKTA1273Y/-1 VS2SB561-C/-1 VSKRC102M//-1 VSKTC3199GR-1 VS2SD2012Y/-1 VSKTC3199GR-1 VS2SD2012Y/-1 VSKTC3199GR-1 VSKTA1266GR-1 J J J J J J J J J J J J J J J J J J J J J J J J J J AB AC AC AC AC AB AB AC AB AB AC AC AC AB AB AC AC AE AC AC AB AF AB AF AB AB Silicon,PNP,KTA1266 GR Silicon,NPN,KTC3203 Y Silicon,PNP,2SB561 C Digital,NPN,KRC102 M Silicon,NPN,2SC1845 F Digital,NPN,KTC3199 GR Silicon,PNP,KTA1266 GR Digital,NPN,KRC104 M Digital,NPN,KTC3199 GR Silicon,PNP,2SA1015 GR Digital,NPN,KRC104 M Silicon,NPN,KTC3203 Y Silicon,NPN,2SC380 O Digital,NPN,KTC3199 GR Silicon,PNP,KTA1266 GR Digital,NPN,KRC107 M Digital,NPN,KRC107 M Silicon,PNP,KTA1273 Y Silicon,PNP,2SB561 C Digital,NPN,KRC102 M Digital,NPN,KTC3199 GR Silicon,NPN,2SD2012 Y Digital,NPN,KTC3199 GR Silicon,NPN,2SD2012 Y Digital,NPN,KTC3199 GR Silicon,PNP,KTA1266 GR VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHDRL104A//-1 VHD1N5402M/-1 VHDRL104A//-1 VHPI31535CD-1 VHEMTZJ5R1B-1 VHEMTZJ3R9B-1 VHEMTZJ3R3B-1 VHEMTZJ130A-1 VHEMTZJ6R2C-1 VHEMTZJ300B-1 VHEMTZJ6R2A-1 J J J J J J J J J J J J J J J J J J J J J J J J J AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AE AB AG AC AC AA AC AC AB AA Silicon,1SS119 Silicon,1SS119 Silicon,1SS119 Silicon,1SS119 Silicon,1SS119 Silicon,1SS119 Silicon,1SS119 Silicon,1SS119 Silicon,1SS119 Silicon,1SS119 Silicon,1SS119 Silicon,1SS119 Silicon,1SS119 Silicon,1SS119 Silicon,RL104A Silicon,1N5402M Silicon,RL104A Phote Interrupter Zener,5.1V,MTZJ5.1B Zener,3.9V,MTZJ3.9B Zener,3.3V,MTZJ3.3B Zener,13V,MTZJ13A Zener,6.2V,MTZJ6.2C Zener,3V,MTZJ3B Zener,6.2V,MTZJ6.2A RFILA0009AWZZ RFILF0072AFZZ RFILF0003AWZZ J J J AE AM IF AG FM IF AK FM IF TRANSISTORS DIODES D2 D5 D7 D81 D91 D311,312 D352 D361~364 D367,368 D401~404 D701~706 D708,709 D941,942 D951 D961~964 D965~968 D971~973 PHM1 ZD351 ZD352 ZD701 ZD941 ZD951 ZD971 ZD972 FILTERS BF351 CF301,302 CF351 DESCRIPTION TRANSFORMERS CD-C410H Q1 Q81 Q91 Q93 Q103~106 Q107,108 Q109 Q110,111 Q121,122 Q124 Q126 Q128 Q301 Q353,354 Q360 Q361 Q701 Q705 Q706 Q707 Q708,709 Q941,942 Q943 Q952 Q953 Q971 PRICE RANK PARTS CODE ! T302 T351 T961 RCILZ0014AWZZ J RCILI0011AWZZ J RTRNP0118AWZZ J AL AM Antenna AD AM IF AW Power VP-XHR82K0000 VP-MK331K0000 VP-DH1R5K0000 VP-XH2R2K0000 RBLN-0001AWZZ VP-DH2R2K0000 VP-DH101K0000 VP-DH102K0000 RFILL0001AWZZ VP-XH2R2K0000 VP-DH2R2K0000 RCILZ0137AFZZ J J J J J J J J J J J J AC AB AC AB AD AB AB AB AE AB AB AA J AB 10 kohm (B),Semi-VR [FM Mute Level] J J J J AD AH AF AH Crystal,456 kHz Crystal,4.5 MHz Ceramic,16.93 MHz Crystal J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AB AB AA AA AB AA AA AA AB AA AB AA AA AA AA AB AB AA AB AA AB AA AB AA AA AA AA AB AB AA AA AA AA AB AB AA AB AA AB AA AA AA AA AB AA AB 0.01 µF,16V 47 µF,10V,Electrolytic 0.1 µF,50V,Electrolytic 0.001 µF,50V 0.033 µF,16V 0.1 µF,50V,Electrolytic 0.068 µF,16V 0.047 µF,16V 180 pF,50V 0.1 µF,16V 330 pF,50V 0.1 µF,16V 0.01 µF,16V 0.0047 µF,16V 0.001 µF,50V 0.47 µF,50V,Electrolytic 1 µF,50V,Electrolytic 47 µF,10V,Electrolytic 0.0033 µF,16V 1 µF,50V,Electrolytic 0.01 µF,16V 1 µF,50V,Electrolytic 0.01 µF,16V 2.2 pF,50V 0.0027 µF,16V 27 pF,50V 0.001 µF,50V 0.033 µF,16V 0.1 µF,50V,Electrolytic 220 µF,6.3V,Electrolytic 0.01 µF,16V 0.47 µF,50V,Electrolytic 0.33 µF,50V,Electrolytic 0.047 µF,16V 100 µF,10V,Electrolytic 4.7 µF,25V,Electrolytic 0.022 µF,6.3V 0.1 µF,16V 0.022 µF,25V 47 µF,10V,Electrolytic 220 pF,50V 100 pF,50V 0.022 µF,25V 0.022 µF,50V 10 µF,16V,Electrolytic 220 pF,50V 100 µF,10V,Electrolytic COILS L1 L104 L105 L107,108 L311 L312 L351,352 L353 L354 L700 L701 L831,832 0.82 µH,Choke 330 µH,Choke 1.5 µH 2.2 µH,Choke Balun 2.2 mmH,Peaking 100 µH,Choke 1 mH,Choke Low Pass Filter 2.2 µH,Choke 2.2 µH,Peaking 0.29 µH VARIABLE RESISTOR VR351 RVR-M0999AFZZ VIBRATORS X351 X352 XL1 XL701 RCRM-0075AFZZ RCRSP0002AWZZ RCRM-0008AWZZ RCRSP0003AWZZ CAPACITORS C1 C2 C3 C4 C5,6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 C20 C21 C22 C24 C25 C30 C31 C32 C33 C34 C35 C37 C38 C39 C40 C41,42 C43,44 C45 C46 C50 C51 C52 C53 C54~57 C58 C59 C67,68 C69,70 C81 –1– VCTYMN1CY103N RC-GZA476AF1A RC-GZA104AF1H VCKYMN1HB102K VCTYPA1CX333K RC-GZA104AF1H VCTYPA1CX683K VCTYPA1CX473K VCKYMN1HB181K VCTYPA1CX104K VCKYMN1HB331K VCTYPA1CX104K VCTYMN1CY103K VCTYMN1CX472K VCKYMN1HB102K RC-GZA474AF1H RC-GZA105AF1H RC-GZA476AF1A VCTYMN1CX332K RC-GZA105AF1H VCTYMN1CY103N RC-GZA105AF1H VCTYMN1CY103N VCCSMN1HL2R2C VCTYMN1CX272K VCCSMN1HL270J VCKYMN1HB102K VCTYPA1CX333K RC-GZA104AF1H RC-GZA227AF0J VCTYMN1CY103K RC-GZA474AF1H RC-GZA334AF1H VCTYPA1CX473K RC-GZA107AF1A RC-GZA475AF1E VCTYMN0JY223N VCTYPA1CX104K VCTYMN1EF223Z RC-GZA476AF1A VCKYBT1HB221K VCKYMN1HB101K VCTYMN1EF223Z VCKZPA1HF223Z RC-GZA106AF1C VCKYMN1HB221K RC-GZA107AF1A CD-C410H,CP-C410 NO. C91 C92 C94,95 C96,97 C101,102 C105,106 C107,108 C109 C111~114 C115,116 C117,118 C119,120 C121,122 C123,124 C127 C128 C129,130 C131,132 C133,134 C135,136 C139,140 C141,142 C145 C146 C147 C148 C150 C151 C152 C153 C320~323 C325 C327 C331 C332 C334 C341,342 C350,351 C352 C353,354 C355 C356 C357 C358 C361 C362 C363 C364 C365 C366 C367,368 C370~372 C373,374 C375 C381 C382 C383 C384 C385 C386 C387 C388 C390 C391 C392 C393 C394 C395 C396 C397 C398 C399 C401~406 C407,408 C409,410 C411,412 C413,414 C417,418 C419,420 C421~424 C425,426 C427,428 PRICE RANK PART CODE RC-GZA476AF1C VCTYMN1EF223Z VCKYMN1HB102K VCTYPA1EX102M VCKYMN1HB102K VCKYMN1HB181K VCKYMN1HB102K VCKZPA1HF473Z VCKYMN1HB331K RC-GZA476AF1A VCTYMN0JY183M VCKYMN1HB561K RC-GZA105AF1H VCTYMN0JY153M VCTYMN1EF223Z RC-GZA335AF1E VCKYMN1HB471K VCKYMN1HB102K RC-GZA226AF1C VCTYPA1CX683K VCTYMN1CX332K RC-GZA105AF1H RC-GZA226AF1C RC-GZA227AF1A VCTYMN1EF223Z VCTYPA1CX823K RC-QZA392AFYJ RC-QZA273AFYJ RC-GZA476AF1A RC-GZA107AF1C VCTYMN1EF223Z VCCSMN1HL330J VCKYMN1HB102K VCKZPA1HF473Z VCTYMN1EF223Z VCCUMN1HJ6R8D VCTYMN1EF223Z VCTYMN1EF223Z RC-GZA106AF1C VCTYMN1EF223Z VCCCPA1HH220J VCKYMN1HB102K RC-GZA225AF1H RC-GZA105AF1H VCTYMN1EF223Z RC-GZA335AF1H VCTYMN1EF223Z RC-GZA226AF1C VCTYMN1EF223Z VCKYMN1HB102K RC-GZA105AF1H RC-GZA105AF1H VCTYMN0JY223M RC-GZA335AF1H VCCCMN1HH120J VCCCMN1HH150J VCTYMN1EF223Z VCKYMN1HB102K VCTYMN1CY103K VCKYMN1HB331K VCKZPA1HF223Z RC-GZA106AF1H VCKYMN1HB471K RC-GZA476AF1C VCTYMN1CX102K RC-GZA105AF1H RC-GZA476AF1C VCTYMN1EF223Z RC-GZA107AF1A VCKYMN1HB221K RC-GZA107AF0J VCTYMN1EF223Z RC-QZA473AFYK VCKYMN1HB391K RC-QZA473AFYK RC-GZA226AF1E VCKYMN1HB101K RC-QZA184AFYJ RC-QZA683AFYJ RC-QZA184AFYJ RC-QZA333AFYJ RC-QZA392AFYJ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AB AA AA AA AA AA AA AA AA AB AA AA AB AA AA AB AA AA AB AA AA AB AB AB AA AB AB AB AB AB AA AA AA AA AA AB AA AA AB AA AA AA AB AB AA AB AA AB AA AA AB AB AB AA AA AA AA AA AA AA AB AA AB AA AB AB AA AB AA AB AA AB AA AB AB AA AC AB AC AB AB DESCRIPTION NO. 47 µF,16V,Electrolytic 0.022 µF,25V 0.001 µF,50V 0.001 µF,25V 0.001 µF,50V 180 pF,50V 0.001 µF,50V 0.047 µF,50V 330 pF,50V 47 µF,10V,Electrolytic 0.018 µF,6.3V 560 pF,50V 1 µF,50V,Electrolytic 0.015 µF,6.3V 0.022 µF,25V 3.3 µF,25V,Electrolytic 470 pF,50V 0.001 µF,50V 22 µF,16V,Electrolytic 0.068 µF,16V 0.0033 µF,16V 1 µF,50V,Electrolytic 22 µF,16V,Electrolytic 220 µF,10V,Electrolytic 0.022 µF,25V 0.082 µF,16V 0.0039 µF,50V,Mylar 0.027 µF,50V,Mylar 47 µF,10V,Electrolytic 100 µF,16V,Electrolytic 0.022 µF,25V 33 pF,50V 0.001 µF,50V 0.047 µF,50V 0.022 µF,25V 6.8 pF (UJ),50V 0.022 µF,25V 0.022 µF,25V 10 µF,16V,Electrolytic 0.022 µF,25V 22 pF (CH),50V 0.001 µF,50V 2.2 µF,50V,Electrolytic 1 µF,50V,Electrolytic 0.022 µF,25V 3.3 µF,50V,Electrolytic 0.022 µF,25V 22 µF,16V,Electrolytic 0.022 µF,25V 0.001 µF,50V 1 µF,50V,Electrolytic 1 µF,50V,Electrolytic 0.022 µF,6.3V 3.3 µF,50V,Electrolytic 12 pF (CH),50V 15 pF (CH),50V 0.022 µF,25V 0.001 µF,50V 0.01 µF,16V 330 pF,50V 0.022 µF,50V 10 µF,50V,Electrolytic 470 pF,50V 47 µF,16V,Electrolytic 0.001 µF,16V 1 µF,50V,Electrolytic 47 µF,16V,Electrolytic 0.022 µF,25V 100 µF,10V,Electrolytic 220 pF,50V 100 µF,6.3V,Electrolytic 0.022 µF,25V 0.047 µF,50V,Mylar 390 pF,50V 0.047 µF,50V,Mylar 22 µF,25V,Electrolytic 100 pF,50V 0.18 µF,50V,Mylar 0.068 µF,50V,Mylar 0.18 µF,50V,Mylar 0.033 µF,50V,Mylar 0.0039 µF,50V,Mylar C433,434 C435,436 C437,438 C439,440 C441,442 C443 C444 C445,446 C451,452 C453,454 C455 C701 C702 C703 C704 C705 C706 C707 C708 C709 C710,711 C715 C717 C718 C801,802 C803,804 C805,806 C808 C809,810 C811~814 C820 C823 C824 C825 C827,828 C829,830 C831 C843,844 C845 C846 C847 C848,849 C850 C851 C852 C853 C855 C871,872 C941 C942 C943 C944 C945 C947,948 C952 C953 C954 C955,956 C957 C961,962 C971,972 C973~975 C976 PRICE RANK PARTS CODE VCTYMN1CX272K RC-GZA226AF1C VCKYMN1HB101K RC-GZA106AF1C RC-GZA105AF1H RC-GZA226AF1C RC-GZA107AF1C VCTYMN1EF223Z RC-GZA225AF1H RC-GZA105AF1H VCKYMN1HB221K VCTYMN1EF223Z RC-GZA227AF0J VCCCMN1HH150J VCCCMN1HH180J VCTYMN1CY103N RC-EZY476AF1C RC-GZA335AF1H VCTYMN1CY103N RC-EZY107AF0J RC-GZA105AF1H RC-GZA227AF0J VCTYMN1EF223Z VCKYMN1HB102K RC-QZ0026AWZZ VCTYMN1CX152K RC-GZA105AF1H RC-GZA476AF1H RC-GZV108AF1E RC-QZA104AFYK VCKYPA1HB102K RC-GZA107AF1H VCKZPA1HF223Z RC-GZW228AF1H RC-GZA107AF1H RC-GZA476AF1H VCKYBT1HB102K VCKYPA1HB221K VCKZPA1HF473Z VCKZPA1HF223Z VCKZPA1HF473Z VCKZPA1HF223Z VCKZPA1HF473Z VCKZPA1HF223Z VCKZPA1HF473Z VCKZPA1HF103Z VCKYBT1HB561K VCKYMN1HB102K VCTYMN1EF223Z RC-GZA107AF1C RC-GZV477AF1E RC-GZW478AF1E VCTYMN1EF223Z RC-GZA106AF1H RC-GZA476AF1C VCKZPA1HF103Z RC-GZA106AF1H RC-QZA224AFYJ VCTYMN1EF223Z RC-QZA473AFYJ RC-GZA107AF1H RC-GZA476AF1H RC-GZA107AF1V DESCRIPTION J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AB AA AB AB AB AB AA AB AB AA AA AB AA AA AA AB AB AA AB AB AB AA AA AB AA AB AB AD AB AA AC AA AH AC AB AA AA AA AA AA AA AA AA AA AA AA AA AA AB AC AG AA AB AB AA AB AB AA AB AC AB AB 0.0027 µF,16V 22 µF,16V,Electrolytic 100 pF,50V 10 µF,16V,Electrolytic 1 µF,50V,Electrolytic 22 µF,16V,Electrolytic 100 µF,16V,Electrolytic 0.022 µF,25V 2.2 µF,50V,Electrolytic 1 µF,50V,Electrolytic 220 pF,50V 0.022 µF,25V 220 µF,6.3V,Electrolytic 15 pF (CH),50V 18 pF (CH),50V 0.01 µF,16V 47 µF,16V,Electrolytic 3.3 µF,50V,Electrolytic 0.01 µF,16V 100 µF,6.3V,Electrolytic 1 µF,50V,Electrolytic 220 µF,6.3V,Electrolytic 0.022 µF,25V 0.001 µF,50V 0.1 µF,50V,Mylar 0.0015 µF,16V 1 µF,50V,Electrolytic 47 µF,50V,Electrolytic 1000 µF,25V,Electrolytic 0.1 µF,50V,Mylar 0.001 µF,50V 100 µF,50V,Electrolytic 0.022 µF,50V 2200 µF,50V,Electrolytic 100 µF,50V,Electrolytic 47 µF,50V,Electrolytic 0.001 µF,50V 220 pF,50V 0.047 µF,50V 0.022 µF,50V 0.047 µF,50V 0.022 µF,50V 0.047 µF,50V 0.022 µF,50V 0.047 µF,50V 0.01 µF,50V 560 pF,50V 0.001 µF,50V 0.022 µF,25V 100 µF,16V,Electrolytic 470 µF,25V,Electrolytic 4700 µF,25V,Electrolytic 0.022 µF,25V 10 µF,50V,Electrolytic 47 µF,16V,Electrolytic 0.01 µF,50V 10 µF,50V,Electrolytic 0.22 µF,50V,Mylar 0.022 µF,25V 0.047 µF,50V,Mylar 100 µF,50V,Electrolytic 47 µF,50V,Electrolytic 100 µF,35V,Electrolytic J J J J J J J J J J J J J J J J AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 0 ohm,Jumper,ø1.4×3.5mm,Ivory 1 kohm,1/8W 100 kohm,1/8W 10 kohm,1/8W 2.2 kohms,1/8W 6.8 kohms,1/8W 100 ohm,1/8W 1 kohm,1/8W 12 kohms,1/8W 27 kohms,1/8W 82 kohms,1/8W 3.3 kohms,1/8W 15 kohms,1/8W 33 kohms,1/8W 10 kohm,1/8W 47 kohms,1/8W RESISTORS R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 R14 R15 –2– VRD-MN2BD000C VRD-MN2BD102J VRD-MN2BD104J VRD-MN2BD103J VRD-MN2BD222J VRD-MN2BD682J VRD-MN2BD101J VRD-MN2BD102J VRD-MN2BD123J VRD-MN2BD273J VRD-MN2BD823J VRD-MN2BD332J VRD-MN2BD153J VRD-MN2BD333J VRD-MN2BD103J VRD-MN2BD473J CD-C410H,CP-C410 NO. R16 R17 R18 R19 R20 R21 R22 R23 R24 R25 R26,27 R28,29 R30 R31 R32 R33 R34 R35 R36,37 R38 R39 R41 R42 R43 R45 R46,47 R49 R54 R56 R57 R58 R60 R61 R70~72 R73,74 R75,76 R77~79 R81 R82 R86~88 R95 R96 R97 R98,99 R101,102 R103,104 R105,106 R107,108 R109 R110 R111,112 R113~115 R117 R118 R119,120 R121,122 R123,124 R125,126 R131,132 R133 R134 R135,136 R137,138 R139,140 R141,142 R145,146 R150 R152 R153,154 R158 R160 R162 R164 R166 R167 R168 R172 R174 R304 R305 R307 R308 PRICE RANK PART CODE VRD-MN2BD152J VRD-MN2BD823J VRD-ST2CD335J VRD-MN2BD393J VRD-MN2BD103J VRD-MN2BD563J VRD-MN2BD682J VRD-MN2BD122J VRD-MN2BD103J VRD-MN2BD122J VRD-MN2BD224J VRD-ST2CD102J VRD-MN2BD153J VRD-MN2BD103J VRD-MN2BD563J VRD-MN2BD562J VRD-MN2BD102J VRD-ST2CD471J VRD-MN2BD473J VRD-MN2BD333J VRD-MN2BD223J VRD-MN2BD472J VRD-MN2BD561J VRD-MN2BD120J VRD-ST2CD102J VRD-MN2BD102J VRD-ST2CD104J VRD-MN2BD102J VRD-MN2BD122J VRD-MN2BD273J VRD-MN2BD681J VRD-MN2BD102J VRD-ST2CD153J VRD-MN2BD102J VRD-MN2BD272J VRD-MN2BD271J VRD-MN2BD102J VRD-MN2BD820J VRD-ST2CD101J VRD-ST2CD102J VRD-ST2CD222J VRD-MN2BD103J VRD-ST2CD222J VRD-MN2BD103J VRD-MN2BD102J VRD-MN2BD222J VRD-MN2BD332J VRD-MN2BD103J VRD-ST2CD103J VRD-MN2BD103J VRD-ST2CD103J VRD-MN2BD103J VRD-ST2CD102J VRD-MN2BD102J VRD-ST2CD560J VRD-MN2BD104J VRD-MN2BD392J VRD-MN2BD562J VRD-MN2BD472J VRD-ST2CD223J VRD-MN2BD683J VRD-MN2BD332J VRD-MN2BD682J VRD-MN2BD561J VRD-MN2BD560J VRD-MN2BD103J VRD-MN2BD103J VRD-MN2BD102J VRD-MN2BD103J VRD-ST2EE471J VRD-RT2HD151J VRD-MN2BD472J VRD-MN2BD472J VRD-MN2BD473J VRD-MN2BD104J VRD-MN2BD120J VRD-ST2CD102J VRD-ST2EE151J VRD-MN2BD681J VRD-MN2BD682J VRD-MN2BD331J VRD-MN2BD330J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA DESCRIPTION 1.5 kohms,1/8W 82 kohms,1/8W 3.3 Mohms,1/6W 39 kohms,1/8W 10 kohm,1/8W 56 kohms,1/8W 6.8 kohms,1/8W 1.2 kohms,1/8W 10 kohm,1/8W 1.2 kohms,1/8W 220 kohms,1/8W 1 kohm,1/6W 15 kohms,1/8W 10 kohm,1/8W 56 kohms,1/8W 5.6 kohms,1/8W 1 kohm,1/8W 470 ohms,1/6W 47 kohms,1/8W 33 kohms,1/8W 22 kohms,1/8W 4.7 kohms,1/8W 560 ohms,1/8W 12 ohms,1/8W 1 kohm,1/6W 1 kohm,1/8W 100 kohm,1/6W 1 kohm,1/8W 1.2 kohms,1/8W 27 kohms,1/8W 680 ohms,1/8W 1 kohm,1/8W 15 kohms,1/6W 1 kohm,1/8W 2.7 kohms,1/8W 270 ohms,1/8W 1 kohm,1/8W 82 ohms,1/8W 100 ohm,1/6W 1 kohm,1/6W 2.2 kohms,1/6W 10 kohm,1/8W 2.2 kohms,1/6W 10 kohm,1/8W 1 kohm,1/8W 2.2 kohms,1/8W 3.3 kohms,1/8W 10 kohm,1/8W 10 kohm,1/6W 10 kohm,1/8W 10 kohm,1/6W 10 kohm,1/8W 1 kohm,1/6W 1 kohm,1/8W 56 ohms,1/6W 100 kohm,1/8W 3.9 kohms,1/8W 5.6 kohms,1/8W 4.7 kohms,1/8W 22 kohms,1/6W 68 kohms,1/8W 3.3 kohms,1/8W 6.8 kohms,1/8W 560 ohms,1/8W 56 ohms,1/8W 10 kohm,1/8W 10 kohm,1/8W 1 kohm,1/8W 10 kohm,1/8W 470 ohms,1/4W 150 ohms,1/2W 4.7 kohms,1/8W 4.7 kohms,1/8W 47 kohms,1/8W 100 kohm,1/8W 12 ohms,1/8W 1 kohm,1/6W 150 ohms,1/4W 680 ohms,1/8W 6.8 kohms,1/8W 330 ohms,1/8W 33 ohms,1/8W NO. R310 R315 R318 R320 R323 R330 R331 R351 R352 R353 R354 R355 R356 R358 R359 R360~362 R363,364 R365,366 R367 R368 R371~374 R376,377 R379 R380 R381 R382 R383 R384 R385 R386 R387 R391,392 R395 R398 R399 R401~403 R405,406 R407,408 R411,412 R413,414 R415~422 R475,476 R477,478 R479,480 R603 R700 R701 R702 R703 R704 R705 R706 R707 R708,709 R711 R712~725 R726 R727 R730 R731~735 R736 R737 R738~740 R741~743 R744 R745~748 R749 R750,751 R752 R753,754 R755 R756,757 R758 R759,760 R761,762 R763,764 R765 R766 R767 R768 R769 R770 –3– PRICE RANK PARTS CODE VRD-MN2BD472J VRD-MN2BD820J VRD-MN2BD471J VRD-ST2CD103J VRD-MN2BD104J VRD-MN2BD272J VRD-ST2CD474J VRD-MN2BD562J VRD-MN2BD102J VRD-MN2BD271J VRD-MN2BD392J VRD-MN2BD332J VRD-MN2BD102J VRD-MN2BD822J VRD-MN2BD182J VRD-MN2BD472J VRD-MN2BD182J VRD-MN2BD103J VRD-MN2BD102J VRD-MN2BD333J VRD-MN2BD102J VRD-MN2BD102J VRD-MN2BD222J VRD-MN2BD152J VRD-MN2BD103J VRD-ST2EE151J VRD-MN2BD562J VRD-MN2BD123J VRD-MN2BD103J VRD-MN2BD473J VRD-MN2BD223J VRD-ST2EE391J VRD-MN2BD562J VRD-MN2BD122J VRD-MN2BD331J VRD-ST2CD102J VRD-MN2BD393J VRD-MN2BD152J VRD-MN2BD223J VRD-MN2BD332J VRD-ST2CD102J VRD-ST2CD104J VRD-ST2CD272J VRD-MN2BD104J VRD-MN2BD103J VRD-MN2BD562J VRD-ST2CD104J VRD-MN2BD222J VRD-MN2BD102J VRD-MN2BD222J VRD-MN2BD103J VRD-MN2BD102J VRD-MN2BD103J VRD-MN2BD102J VRD-MN2BD103J VRD-MN2BD102J VRD-MN2BD103J VRD-MN2BD102J VRD-MN2BD102J VRD-MN2BD103J VRD-ST2CD101J VRD-MN2BD103J VRD-MN2BD102J VRD-MN2BD103J VRD-MN2BD822J VRD-MN2BD102J VRD-ST2CD101J VRD-MN2BD104J VRD-MN2BD822J VRD-MN2BD332J VRD-MN2BD822J VRD-MN2BD104J VRD-RT2HD100J VRD-MN2BD103J VRD-MN2BD102J VRD-ST2CD102J VRD-MN2BD102J VRD-MN2BD332J VRD-MN2BD122J VRD-ST2CD122J VRD-MN2BD122J VRD-ST2CD103J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA DESCRIPTION 4.7 kohms,1/8W 82 ohms,1/8W 470 ohms,1/8W 10 kohm,1/6W 100 kohm,1/8W 2.7 kohms,1/8W 470 kohms,1/6W 5.6 kohms,1/8W 1 kohm,1/8W 270 ohms,1/8W 3.9 kohms,1/8W 3.3 kohms,1/8W 1 kohm,1/8W 8.2 kohms,1/8W 1.8 kohms,1/8W 4.7 kohms,1/8W 1.8 kohms,1/8W 10 kohm,1/8W 1 kohm,1/8W 33 kohms,1/8W 1 kohm,1/8W 1 kohm,1/8W 2.2 kohms,1/8W 1.5 kohms,1/8W 10 kohm,1/8W 150 ohms,1/4W 5.6 kohms,1/8W 12 kohms,1/8W 10 kohm,1/8W 47 kohms,1/8W 22 kohms,1/8W 390 ohms,1/4W 5.6 kohms,1/8W 1.2 kohms,1/8W 330 ohms,1/8W 1 kohm,1/6W 39 kohms,1/8W 1.5 kohms,1/8W 22 kohms,1/8W 3.3 kohms,1/8W 1 kohm,1/6W 100 kohm,1/6W 2.7 kohms,1/6W 100 kohm,1/8W 10 kohm,1/8W 5.6 kohms,1/8W 100 kohm,1/6W 2.2 kohms,1/8W 1 kohm,1/8W 2.2 kohms,1/8W 10 kohm,1/8W 1 kohm,1/8W 10 kohm,1/8W 1 kohm,1/8W 10 kohm,1/8W 1 kohm,1/8W 10 kohm,1/8W 1 kohm,1/8W 1 kohm,1/8W 10 kohm,1/8W 100 ohm,1/6W 10 kohm,1/8W 1 kohm,1/8W 10 kohm,1/8W 8.2 kohms,1/8W 1 kohm,1/8W 100 ohm,1/6W 100 kohm,1/8W 8.2 kohms,1/8W 3.3 kohms,1/8W 8.2 kohms,1/8W 100 kohm,1/8W 10 ohm,1/2W 10 kohm,1/8W 1 kohm,1/8W 1 kohm,1/6W 1 kohm,1/8W 3.3 kohms,1/8W 1.2 kohms,1/8W 1.2 kohms,1/6W 1.2 kohms,1/8W 10 kohm,1/6W CD-C410H,CP-C410 NO. R771 R772 R773~775 R776 R777,778 R779 R780,781 R782 R783 R785 R786 R788 R789 R792 R793 R794 R795 R797 R798 R799 R803,804 R805,806 R807,808 R809,810 R811,812 R815 R825 R835,836 R843,844 R845 R943,944 R945 R946 R947 R948,949 R951 R952 R953 R972 R973 R974 R975,976 R977,978 R981,982 PRICE RANK PART CODE VRD-MN2BD122J VRD-MN2BD104J VRD-MN2BD182J VRD-MN2BD820J VRD-ST2CD222J VRD-MN2BD102J VRD-MN2BD103J VRD-MN2BD392J VRD-ST2CD392J VRD-MN2BD101J VRD-MN2BD102J VRD-MN2BD562J VRD-ST2CD222J VRD-ST2CD392J VRD-ST2CD562J VRD-ST2CD123J VRD-MN2BD222J VRD-MN2BD102J VRD-MN2BD151J VRD-MN2BD120J VRD-MN2BD332J VRD-MN2BD102J VRD-MN2BD181J VRD-ST2EE4R7J VRD-RT2HD271J VRD-ST2CD103J VRD-ST2EE103J VRD-RT2HD331J VRD-ST2EE2R2J VRD-ST2CD100J VRD-ST2EE180J VRD-MN2BD333J VRD-ST2EE101J VRD-ST2EE271J VRD-MN2BD223J VRD-ST2EE152J VRD-ST2CD333J VRD-ST2CD103J VRD-ST2CD332J VRD-ST2CD101J VRD-ST2CD123J VRD-ST2CD221J VRD-ST2EE2R2J VRD-ST2EE2R2J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J DESCRIPTION NO. AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 1.2 kohms,1/8W 100 kohm,1/8W 1.8 kohms,1/8W 82 ohms,1/8W 2.2 kohms,1/6W 1 kohm,1/8W 10 kohm,1/8W 3.9 kohms,1/8W 3.9 kohms,1/6W 100 ohm,1/8W 1 kohm,1/8W 5.6 kohms,1/8W 2.2 kohms,1/6W 3.9 kohms,1/6W 5.6 kohms,1/6W 12 kohms,1/6W 2.2 kohms,1/8W 1 kohm,1/8W 150 ohms,1/8W 12 ohms,1/8W 3.3 kohms,1/8W 1 kohm,1/8W 180 ohms,1/8W 4.7 ohms,1/4W 270 ohms,1/2W 10 kohm,1/6W 10 kohm,1/4W 330 ohms,1/2W 2.2 ohms,1/4W 10 ohm,1/6W 18 ohms,1/4W 33 kohms,1/8W 100 ohm,1/4W 270 ohms,1/4W 22 kohms,1/8W 1.5 kohms,1/4W 33 kohms,1/6W 10 kohm,1/6W 3.3 kohms,1/6W 100 ohm,1/6W 12 kohms,1/6W 220 ohms,1/6W 2.2 ohms,1/4W 2.2 ohms,1/4W ! ! ! J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AE AF AH AC AC AC AD AA AB AA AD AC AB AE AB AG AF AF AE AG AD AD AD AT AV AC AD AD AS AP AP AR AH AD AD Connector Ass’y,6-6Pin Connector Ass’y,8-12Pin Connector Ass’y,6-10-2Pin Plug,5Pin Plug,8Pin Plug,6Pin Plug,10Pin Plug,3Pin Plug,7Pin Plug,2Pin Plug,10Pin Plug,10Pin Plug,6Pin Plug,11Pin Plug,2Pin Connector Ass’y,5-5Pin Connector Ass’y,8-8Pin Connector Ass’y,6-6Pin Connector Ass’y,3Pin Connector Ass’y,8Pin Fuse,T500mA L,250V Fuse,T2.5A L 250V Fuse,T1.6A L 250V FM Front End FL Display Flat Cable,2Pin Flat Cable,2Pin Jack,Headphones Motor with Chassis [Disc] Motor with Gear [Slide] Motor with Worm [T/T Up/Down] Motor with Pulley [Tape] Remote Sensor,SPSP440 Antenna Terminal Jack,VIDEO/AUX. SO801 SOLM1,2 SW1 SW2 SW3 SW4 SW701 QTANA0404AWZZ RPLU-0002AWZZ QSW-P0004AWZZ QSW-F0001AWZZ QSW-P0005AWZZ QSW-F9001AWZZ 92LSWICH-1401A J J J J J J J AF AH AE AD AD AE AC SW702 SW703 SW704 SW705 SW706 SW709 SW710 SW711 SW712 SW713 SW714 SW715 SW717 SW718 SW719 SW721 SW722 SW723 SW724 SW725 SWM3 SWM4 SWM5 92LSWICH-1401A 92LSWICH-1401A 92LSWICH-1401A 92LSWICH-1401A 92LSWICH-1401A 92LSWICH-1401A 92LSWICH-1401A 92LSWICH-1401A 92LSWICH-1401A 92LSWICH-1401A 92LSWICH-1401A 92LSWICH-1401A 92LSWICH-1401A 92LSWICH-1401A 92LSWICH-1401A 92LSWICH-1401A 92LSWICH-1401A 92LSWICH-1401A 92LSWICH-1401A 92LSWICH-1401A 92LM-SW1676A QSW-F9003AWZZ 92LM-SW1658A J J J J J J J J J J J J J J J J J J J J J J J AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AG AB DESCRIPTION Terminal,Speaker Solenoid Ass’y Switch,Push Type [Open/Close] Switch,Leaf Type [Mecha Up] Switch,Push Type [Disc Number] Switch,Push Type [Pickup In] Switch,Key Type [Random/Demo] Switch,Key Type [Volume Down] Switch,Key Type [X-BASS] Switch,Key Type [Volume Up] Switch,Key Type [Open/Close] Switch,Key Type [Disc Skip] Switch,Key Type [Rec./Pause] Switch,Key Type [Up] Switch,Key Type [Stop] Switch,Key Type [Play] Switch,Key Type [Down] Switch,Key Type [Tuning Up] Switch,Key Type [Tuning Down] Switch,Key Type [Power] Switch,Key Type [Clock] Switch,Key Type [Timer/Sleep] Switch,Key Type [Memory/Set] Switch,Key Type [CD] Switch,Key Type [Tuner] Switch,Key Type [Tape] Switch,Key Type [Aux] Switch,Leaf Type [Fool Proof] Switch,Leaf Type [F.A.S.] Switch,Leaf Type [CAM] CASSETTE MECHANISM PARTS OTHER CIRCUITRY PARTS BI901/CNS901 QCNWN0890AWZZ BIM1/CNSM1 QCNWN0897AWZZ BIM5/CNS10/CNS5 QCNWN0894AWZZ CNP1 QCNCM931EAFZZ CNP2 92LCONE8P53253 CNP3 92LCONE6P53253 CNP10 92LCONEAP53254 CNP101 QCNCM742CAFZZ CNP102 QCNCM588GAFZZ CNP301 QCNCM602BAFZZ CNP303 QCNCW010KAWZZ CNP402 QCNCM010KAWZZ CNP901 QCNCM742FAFZZ CNPM1 QCNCM932MAFZZ CNPM2 QCNCM030BAWZZ CNS1A/B QCNWN0891AWZZ CNS2A/B QCNWN0892AWZZ CNS3A/B QCNWN0893AWZZ CNS101 QCNWN0895AWZZ CNS102 QCNWN0896AWZZ F1 92LFUSE-T501E F962 92LFUSET252E F963 92LFUSE-T162-E FE301 RTUNS0007AWZZ FL701 VVKFIP9EM7R-1 FWM1 QCNWN0328AWZZ FWM2 QCNWN0338AWZZ J801 QJAKM0005AWZZ M1 92LMTR1858CASY M2 92LMTR1854BASY M3 92LMTR2037AS1 MM1 RMOTV0006AWM1 RX701 VHLSPSP440/-1 SO301 QTANC0103AWZZ SO401 QSOCJ0209AWZZ PRICE RANK PARTS CODE –4– 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 52 53 55 LCHSM0014AW01 LPLTP0001AWZZ LPLTP0002AWZZ NDAIR0004AW01 NDAIR0005AW01 NGERH0024AWZZ NROLY0002AWZZ NFLYC0002AWZZ NFLYC0003AWZZ MLEVP0024AW01 NGERH0027AWZZ NGERH0028AWZZ NGERH0030AWZZ NGERH0032AWZZ NPLYB0004AWZZ MLEVP0026AWZZ MLEVP0027AWZZ MLEVP0028AWZZ MLEVP0069AWZZ LHLDS1001AW01 PGIDM0007AWZZ PGIDM0009AWZZ MLEVF0004AWFW MLEVF0005AW01 MLEVF0006AW01 MLEVF0007AW01 MLEVF0008AW01 LANGT0025AWFW LANGT0026AWFW LANGT0033AWFW MSPRP0005AWFW MSPRC0008AWFJ MSPRD0031AWFJ MSPRD0032AWFJ MSPRD0033AWFJ MSPRD0034AWFJ MSPRD0035AWFJ MSPRD0036AWFJ MSPRD0037AWFJ MSPRD0038AWFJ MSPRD0039AWFJ MSPRD0040AWFJ NBLTK0009AWZZ NBLTK0011AWZZ NBLTK0012AWZZ 92LM-LEV1756A 92LM-TSPR1756C 92LMRPH1746A J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AN AD AD AG AG AB AF AG AH AH AE AB AE AC AB AC AC AC AB AE AC AC AB AE AD AC AD AD AC AB AB AB AB AB AB AB AB AB AB AB AB AB AC AC AB AB AB AM Main Chassis Ass’y Plate,Head [Tape 1] Plate,Head [Tape 2] Take-Up Reel Ass’y [Tape 1] Take-Up Reel Ass’y [Tape 2] Gear,Supply Reel Pinch Roller Ass’y Flywheel Ass’y [Tape 1] Flywheel Ass’y [Tape 2] Lever,FF/REW Roller Ass’y Gear,Cam Gear,Flywheel Gear,Play Idler Gear,FF Sensor,Wing Lever,Trigger Lever,Lock [Tape 1] Lever,Eject Obstruct [Tape 1] Lever,Eject Obstruct [Tape 2] Holder,Bearing Guide,Cassette [Tape 2] Guide,Cassette [Tape 1] Lever,Over Strok [Tape 1] Lever,Over Strok Ass’y [Tape 2] Lever,Mode Ass’y Lever,Idler Ass’y [Tape 1] Lever,Idler Ass’y [Tape 2] Blacket Motor Blacket Hold Blacket,Switch Spring,Cassette Spring,Back Tention Spring,Lock Lever [Tape 1] Spring,Mode Lever Spring,Play Idler Lever Spring,Play Roller Spring,Eject Obstruct [Tape 1] Spring,Play Return Spring,Over Strok Lever Spring,Trigger Lever Spring,FR Lever Spring,Eject Obstruct [Tape 2] Belt,Sub Belt,Main [Tape 1] Belt,Main [Tape 2] Lever,Lock [Tape 2] Spring,Lock Lever [Tape 2] Head,Record/Playback CD-C410H,CP-C410 NO. 56 57 58 59 501 502 503 504 505 506 507 508 510 MM1 SOLM1 SWM3 SWM4 SWM5 PRICE RANK DESCRIPTION J J J J J J J J J J J J J J J J J J AG AB AA AA AA AA AA AA AB AC AA AA AA AR AH AC AG AB Head,Erase Cap,Supply Reel Spring,Supply Cap Nylon Band,80mm Screw,ø2.6×2.5mm Screw,ø2×4mm Screw,ø2×5mm Washer,ø1.5×ø3.8×0.5mm Washer,ø2mm Screw,Lock Lever Screw,ø2×5mm Washer,ø2.3×ø3.4×0.25mm Washer,ø1.8×ø4×0.5mm Motor with Pulley [Tape] Solenoid Ass’y Switch,Leaf Type [Fool Proof] Switch,Leaf Type [F.A.S.] Switch,Leaf Type [CAM] Gear,Middle Gear,Drive Rail,Guide Shaft,Guide Cushion Pickup Unit Ass’y Pickup Unit (Not Replacement Item) Gear,Rack Spring,Rack Screw,ø2.6×6mm Screw,ø2×5mm Screw,ø2×3mm Washer,ø1.5×ø3.8×0.25mm Motor with Chassis [Disc] Motor with Gear [Slide] Switch,Leaf Type [Pickup In] PART CODE 92LM-EH1658A 92LM-REL1676B 92LM-CSPR1676B 92LN-BAND1318A 92LS2R6S1746A 92L2TTS+4BZ 92L2TTS+5BZ 92L1R5WC3R8R5P 92L2R2TW0 LX-BZ0004AWFD XHPSD20P05000 92L2R3W3R4R25P 92L1R8WC4-R5P RMOTV0006AWM1 RPLU-0002AWZZ 92LM-SW1676A QSW-F9003AWZZ 92LM-SW1658A CD MECHANISM PARTS ! 301 302 303 304 305 306 306- 1 NGERH0011AWZZ NGERH0012AWZZ MLEVP0010AWZZ NSFTM0002AWFW 92LM-CUSN1524A 92LHPC1MASY ———— J J J J J J AC AC AC AE AC BG — 306- 2 306- 3 701 702 703 704 M1 M2 SW4 NGERR0043AFZZ MSPRC0961AFZZ 92L2R6S+6CZ 92L2TTS+5BB 92L2S+3PZ 92L1R5WC3R8R25 92LMTR1858CASY 92LMTR1854BASY QSW-F9001AWZZ J J J J J J J J J AC AA AB AB AA AA AS AP AE CABINET PARTS ! ! 201 201- 1 92LCAB2529AS1 ———— J 201- 2 201- 3 202 203 PCUSG0022AWZZ HDECQ0203AWSA GCAB-1045AWSB GITAR0208AWSA J J J J 203 203 204 204- 1 GITAR0209AWSA J GITAR0210AWSA J 92LMEC2475CTS1 J ———— 204- 2 206 206- 1 HDECQ0173AWSA J 92LMEC2475CTS2 J ———— 206- 2 208 209 209- 1 HDECQ0174AWSA J MSPRD0093AWFJ J 92LCAB2475BS1 J ———— 209- 2 210 210- 1 PCUSG0022AWZZ J 92LCAB2475CS1 J ———— 210- 2 211 213 214 215 216 216 PCUSG0022AWZZ GCOVA1135AWSB MLIFP0003AWZA MSPRD0092AWFJ LCHSM0045AWFW QACCB0003AW00 QACCE0008AW00 J J J J J J J 217 218 220 221 222 223 92LN-BAND1318A LANGT0043AWFW LANGT0045AWFW JKNBZ0335AWSA JKNBZ0334AWSA JKNBZ0332AWSA J J J J J J AV Front Panel Ass’y — Front Panel (Not Replacement Item) AB Cushion,Leg AG Panel,Amp. AL Top Cabinet AG Back Board [Except for UK/ Thailand] AG Back Board [For UK] AF Back Board [For Thailand] AL Cassette Holder Ass’y,Tape 1 — Cassette Holder Tape 1 (Not Replacement Item) AD Panel,Cassette,Tape 1 AL Cassette Holder Ass’y,Tape 2 — Cassette Holder Tape 2 (Not Replacement Item) AD Panel,Cassette,Tape 2 AB Spring,Cassette,Tape 2 AK Side Panel Ass’y,Left — Side Panel,Left (Not Replacement Item) AB Cushion,Leg AK Side Panel Ass’y,Right — Side Panel,Right (Not Replacement Item) AB Cushion,Leg AF Cover,CD Tray Damper AB Spring,Cassette,Tape 1 AR Main Chassis BA AC Power Supply Cord [For UK] AG AC Power Supply Cord [Except For UK] AA Nylon Band,80mm AC Bracket,Heat Sink Support AD Bracket,Terminal AC Knob,Tuner/Memory AD Knob,Function AD Knob,Operation A NO. PRICE RANK PARTS CODE 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 252 253 254 255 256 257 260 261 JKNBZ0333AWSA JKNBZ0337AWSB JKNBZ0336AWSA MLEVP0068AWZZ LCHSZ0011AWZZ NGERK0004AWZZ MSPRC0021AWFJ NGERW0006AWZZ NPLYD0001AWZZ NGERK0005AWZZ MLEVP0066AWZZ NGERH0064AWZZ NGERK0003AWZZ LHLDZ1141AWZZ NGERH0065AWZZ NBLTK0029AWZZ MSPRD0044AWFJ MLEVP0067AWZZ LCHSZ0010AWZZ NROLP0009AWZZ MLEVP0070AWZZ MSPRC0020AWFJ GCAB-1044AWSA LHLDZ1139AWSA 92LHOLD2037AS1 NTNT-0018AWSA LHLDZ1140AWZZ PRDAR0069AWFW LANGT0042AWFW PRDAR0053AWFW LBSHC0002AWZZ PCUSG0027AWZZ MSPRC0024AWFW 92LFSHOLD1652T TSPC-0427AWZZ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AC AD AC AB AG AB AB AC AB AB AE AD AC AB AB AB AB AC AM AB AB AB AM AD AK AK AB AF AC AM AD AB AB AB AC 262 TCAUS0019AWZZ J AD 263 264 265 267 268 268 269 270 271 601 602 603 604 605 606 608 609 610 611 612 613 614 617 618 619 LHLDZ1087AWSA 92LLUG1746A PSLDM5002AWZZ RPLU-0002AWZZ QCNWN0769AWZZ 92LCAUT1706A1 92LCAUT1706B 92LLABL1420A1 RCORF0002AWZZ XESSD30P10000 LX-JZ0022AFFD XEBSD30P10000 XHBSD40P08000 XJBSD30P06000 XJBSF30P10000 XEBSF30P12000 XJBSF30P08000 LX-TZ0019AFZZ XEBSD26P12000 XEBSD30P12000 LX-EZ0005AWFD XJSSF30P10000 LX-JZ0002AWFD XJBSD30P08000 LX-JZ0003AWFF J J J J J J J J J J J J J J J J J J J J J J J J J AC AA AH AD AC AA AC AE AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA DESCRIPTION Knob,Operation B Knob,X-BASS Knob,Open/Close,Rec./Playback Lever,Change Chassis,CD Mechanism Gear,Bevel Spring,Worm Wheel Gear,Worm Wheel Pulley Gear,Loading Lever,Shift Gear,Cam Gear,Drive Support,Pitch Gear,Turntable Belt,Drive Spring,Lock Lever Lever,Lock Chassis,Loading Roller Lever,T/T Lock Spring,T/T Lock Lever CD Player Base Support,Stabilizer Stabilizer Ass’y Turntable Guide Heat Sink Bracket Heat Sink,Fin Type,Small Bushing,AC Power Supply Cord Worm Wheel Cushion Spring,Solenoid Holder,Fuse Label,Specifications [For Thailand] Label,Caution [For Thailand Only] Holder,FL Display Lug,Terminal Shield Solenoid Ass’y Wire Lug Label,Class 3A Label,Laser Label,Class 1 Core Screw,ø3×10mm Screw,ø3×8mm Screw,ø3×10mm Screw,ø4×8mm Screw,ø3×6mm Screw,ø3×10mm Screw,ø3×12mm Screw,ø3×8mm Screw,Special Screw,ø2.6×12mm Screw,ø3×12mm Screw,Special Screw,ø3×10mm Screw,ø3×10mm Screw,ø3×8mm Screw,ø3×12mm ACCESSORIES/PACKING PARTS 1 2 3 3 4 5 5 5 SPAKA0124AWZZ1 SPAKP0013AWZZ1 SPAKC0505AWZZ SPAKC0507AWZZ 92LBAG1460C1 TINSE0155AWZZ TINST0021AWZZ TINSZ0210AWZZ J J J J J J J J 6 7 8 9 9- 1 10 QANTL0005AWZZ 92LF-ANT1535A 92LCARD1751A RRMCG0099AWSA 92LLID1782A 92LBAG1770A J J J J J J –5– AH Packing Add.,Left/Right AC Polyethylene Bag,Unit AN Packing Case Packing Case AB Polyethylene Bag, Accessories AE Operation Manual [For UK] AH Operation Manual [For Thailand] AL Operation Manual [Except For UK/Thailand] AG AM Loop Antenna AF FM Antena AB Registration Card [For UK Only] AR Remote Control AQ Battery Lid,Remote Control AB Polyethylene Bag,AC Power Supply Cord [For UK Only] CD-C410H,CP-C410 NO. 11 PRICE RANK PART CODE TLABE0153AWZZ J DESCRIPTION NO. AB Label P.W.B. ASSEMBLY (Not Replacement Item) PWB-A1~3 92LPWB2529MANS J PWB-B1~3 92LPWB2529TUNS J PWB-C PWB-D PWB-E QPWBF0106AWZZ J QPWBF0027AWZZ J QPWBF0341AWZZ J — Main/Display/Headphones (Combined Ass’y) — Tuner/Power/Powe (Combined Ass’y) AF Tape Mechanism (PWB Only) AD CD Motor (PWB Only) AB Motor (PWB Only) CP-C410 SPEAKER BOX PARTS 701 702 703 704 705 706 707 708 SP1,2 92L121-0068 92L051-0036 92L291-0032 92L351-0125 92L316-0030 92L394-0024 92L502-0008 92L372-0087 VSP0010PBS78A J J J J J J J J J AP Net Frame Ass’y AW Cabinet Ass’y Speaker Cord AD Label,Specifications AN Duct Panel AC Port Cushion Support,Woofer AB Screw,ø4×32mm AU Woofer ACCESSORIES/PACKING PARTS 1 2 92L411-0064 92L412-0063 J J 3 92L353-0046 J Polyethylene Bag,Speaker AM Packing Add.,Speaker (Top/Bottom) Feature Label –6– PARTS CODE PRICE RANK DESCRIPTION CD-C410H,CP-C410 CD-C410H A 306-2 306 306-1 701 306-3 B 304 701 302 C 704 702 702 301 D 303 703 E M1 F 305 M2 305x2 G SW4 H PWB-D 1 2 3 4 Figure 7 CD MECHANISM EXPLODED VIEW 7 –– –– 52 5 6 CD-C410H,CP-C410 CD-C410H TAPE1 TAPE2 504 57 58 A 55 56 6 39 23 504 3 39 57 58 504 6 B 4 18 503x2 33 506 34 503x3 503x2 38 7 C 24 5 504 503x3 509 37 7 36 25 38 36 27 55 21 26 20 42 20 22 31 17 19 2 D 31 1 35 13 507 E SWM5 52 14 SOLM1 41 501x2 15 53 32 506 13 SWM4 502 40 504 508 30 12 510 45 503 28 F 9 SWM3 12 MM1 8 43 502x2 10 PWB-C 16 G BELT CONNECTION 10 505 44 503 11 MOTOR 43 29 H 9 1 45 2 44 502 8 3 4 Figure 8 TAPE MECHANISM EXPLODED VIEW 8 –– ––53 5 6 CD-C410H,CP-C410 CD-C410H 619x7 A 209 262 203 618 PWB-A1 606 209-1 B 261 601x9 606x2 PWB-A2 270 618 619 253 a 209-2 C 602 618x2 263 FL701 260x2 PWB-A3 224 603 618 603x3 222 201-3 D 220 253 PWB-B1 221 b a' 603x2 223 Silicon Grease 254 603 603x2 225 252 226 213 605 254 E 618 218 201 213 201-1 204 201-2 204-1 601x6 603 604x4 TAPE MECHANISM F 606x2 PWB-B2 264x2 201-2 204-2 214 210 210-1 PWB-B3 260x4 206-1 b' G 216 271x2 619 255 206-2 606 208 206 210-2 H 215 217 1 2 3 4 Figure 9 CABINET EXPLODED VIEW (1/2) –– 54 9 –– 5 6 CD-C410H,CP-C410 CD-C410H 247 614 A 608x2 248 202 B 249 244 243 C 269 SW3 243 245 243 268 D 608x2 211 246 617 240 243x2 CD MECHANISM 610 E 611 238 237 236 250 603 241 229 243 610 229 232 235 613 F 239 231 230 234 227 SW2 250 233 609x2 G 243 242 603 228 M3 257 612x4 H PWB-E 267 243 1 2 3 4 Figure 10 CABINET EXPLODED VIEW (2/2) – 10 55 – 5 6 CD-C410H,CP-C410 CP-C410 A 704 B 702 703 701 C 707 SP1,2 D 708x4 SH AR P E 706 Woofer F 705 Black Red G H 1 2 3 4 Figure 11 SPEAKER EXPLODED VIEW – 11 56 – 5 6 CD-C410H,CP-C410 PACKING METHOD (FOR UK ONLY) Setting position of switches and knobs Tape Mechanism STOP CD-C410H SPAKA0124AWZZ SPAKP0013AWZZ1 SPAKC0505AWZZ 92LBAG1460C1 TiNSE0155AWZZ QANTL0005AWZZ 92LF-ANT1535A 92LCARD1751A RRMCG0099AWSA 1. Polyathylene Bag, Speaker 2. Packing Add.,Speaker (Top/Bottom) 3. Feature Label 92LBAG1770A TLABE0153AWZZ 2 P O T FR ON T 1 1 M O T T O B 10 3 O P 4,5,6,7,8,9 T 1. Packing Add., Left/Right 2. Polyathylene Bag, Unit 3. Packing Case 4. Polyethylene Bag, Accessories 5. Operation Manual 6. AM Loop Antenna 7. FM Antenna 8. Registration Card 9. Remote Control 10. Polyethylene Bag, AC Power Supply Cord 11. Label CP-C410 2 T ON FR 3 CK BA – 12 57 – 92L411-0064 92L412-0063 92L353-0046 CD-C410H,CP-C410 A9705-4778NS•HA•M Writer and Editor: Quality & Reliability Control Center of Audio-Visual Systems Group, Sharp Corp. – 58 – Printed in Europe SG • SK • STCL