Download Sharp CP-C602 Service manual
Transcript
CD-C602,CP-C602 SERVICE MANUAL No. S1903CDC602// CD-C602 CP-C602 CD-C602 mini component system consisting of CD-C602 mini component system, CP-C602 and rear (GBOXS0020AWM1) speaker system. • In the interests of user-safety the set should be restored to its original condition and only parts identical to those specified be used. CONTENTS Page IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY)....................................................................................................... 2 SPECIFICATIONS ............................................................................................................................................................. 2 NAMES OF PARTS ........................................................................................................................................................... 3 QUICK GUIDE ................................................................................................................................................................... 5 DISASSEMBLY .................................................................................................................................................................. 6 REMOVING AND REINSTALLING THE MAIN PARTS ..................................................................................................... 8 ADJUSTMENT ................................................................................................................................................................... 9 NOTES ON SCHEMATIC DIAGRAM .............................................................................................................................. 11 TYPE OF TRANSISTER .................................................................................................................................................. 11 WAVEFORMS OF CD CIRCUIT ...................................................................................................................................... 12 BLOCK DIAGRAM ........................................................................................................................................................... 13 SCHEMATIC DIAGRAM / WIRING SIDE OF P.W.BOARD .............................................................................................. 16 VOLTAGE ........................................................................................................................................................................ 28 TROUBLESHOOTING ..................................................................................................................................................... 29 FUNCTION TABLE OF IC ................................................................................................................................................ 33 LCD SEGMENT ................................................................................................................................................................ 38 PARTS GUIDE/EXPLODED VIEW PACKING OF THE SET (FOR U.S.A. ONLY) SHARP CORPORATION –1– This document has been published to be used for after sales service only. The contents are subject to change without notice. CD-C602,CP-C602 FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL. IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY) BEFORE RETURNING THE AUDIO PRODUCT (Fire & Shock Hazard) Before returning the audio product to the user, perform the following safety checks. 1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the audio product. 2. Inspect all protective devices such as insulating materials, cabinet, terminal board, adjustment and compartment covers or shields, mechanical insulators etc. 3. To be sure that no shock hazard exists, check for leakage current in the following manner. * Plug the AC line cord directly into a 120 volt AC outlet. * Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet parts and a known earth ground, such as conduit or electrical ground connected to earth ground. * Use a VTVM or VOM with 1000 ohm per volt, or higher, sensitivity to measure the AC voltage drop across the resistor (See diagram). * Connect the resistor connection to all exposed metal parts having a return path to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor. VTVM AC SCALE 1.5k ohms 10W 0.15µF TEST PROBE TO EXPOSED METAL PARTS CONNECT TO KNOWN EARTH GROUND All check must be repeated with the AC line cord plug connection reversed. Any reading of 0.3 volt RMS (this corresponds to 0.2 milliamp. AC.) or more is excessive and indicates a potential shock hazard which must be corrected before returning the audio product to the owner. SPECIFICATIONS CD-C602 CP-C602 ● General Power source: ● Front speaker section AC 120 V, 60 Hz Power consumption: 25 W Dimensions: Width; 10-5/8" (270 mm) Height; 11-1/16" (280 mm) Depth; 13-1/8" (332.5 mm) Weight: Headphones; 16-50 ohms (recommended; 32 ohms) Front speaker ; 6 ohms Rear speaker ; 12 ohms 5W Impedance: 6 ohms Dimensions: Width; 6-11/16" (170 mm) Height; 11-1/16" (280 mm) Depth; 5-15/16" (151 mm) Weight: 3.1 lbs. (1.4 kg)/each GBOXS0020AWM1 ● Rear speaker section ● Tuner section Frequency range: 4" (10 cm) full-range speaker Maximum input power: 9.2 lbs. (4.2 kg) ● Amplifier section Output terminals: Type: FM; 87.5-108 MHz AM; 530-1,720 kHz ● Cassette deck section Frequency response: 50-14,000 Hz (Normal tape) Signal/noise ratio: 50 dB (TAPE 1, recording/playback) 55 dB (TAPE 2, playback) Wow and flutter: 0.15 % (WRMS) Type: 3-3/32" (8 cm) full-range speaker Maximum input power: 4W Impedance: 12 ohms Dimensions: Width; 6" (150 mm) Height; 6" (150 mm) Depth; 3" (78 mm) Weight: 0.9 lbs. (0.4 kg)/each ● Compact disc player section Type: 3-disc multi-play compact disc player Signal readout: Non-contact, 3-beam semiconductor laser pickup D/A converter: 1-bit D/A converter Frequency response: 20 -20,000 Hz Dynamic range: 90 dB (1 kHz) Specifications for this model are subject to change without prior notice. –2– CD-C602,CP-C602 CD-C602 NAMES OF PARTS 1 ■ Front panel 11. Disc Tray 12. 13. 14. 15. 16. 17. 18. 19. CD Play Indicator: Disc Number Indicators FM Stereo Mode Indicator: ST Extra Bass Indicator: X-BASS Memory Indicator CD Pause Indicator: CD Repeat Indicator: FM Stereo Indicator: 2 3 1 Power Button Memory Button Extra Bass Button: X-BASS Volume Up/Down Buttons: / Function Selector Button Band Selector Button Tuning Up/Down Buttons: / (CD) Track Down/Review Button: (TUNER) Preset Down Button: Stop Button: Play/Repeat Button: / (CD) Track Up/Cue Button: / (TUNER) Preset Up Button: Disc Skip Button Open/Close Button: Headphone Socket (TAPE 1) Cassette Compartment (TAPE 2) Cassette Compartment (TAPE 1) Record Button: (TAPE 1) Play Button: (TAPE 1) Rewind Button: (TAPE 1) Fast Forward Button: (TAPE 1) Stop/Eject Button: / (TAPE 2) Play Button: (TAPE 2) Stop/Eject Button: / 2 3 7 8 10. 11. 12. 13. 14. 15. 16. 17. 3 18. 19. 20. 3 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 4 5 ST X-BASS 6 MEMORY 9 10 11 12 13 14 / 15 16 17 18 24 26 27 2829 30 19 20 21 22 23 25 31 32 ■ Rear panel 11. 12. 13. AC Power Input Socket Speaker Terminals FM/AM Loop Aerial Socket 1 2 –3– 3 CD-C602,CP-C602 ■ Speaker section 1 GBOXS0020AWM1 ● Rear speaker 11. 12. 2 Woofer Speaker Wire CP-C602 ● Front speaker 13. 14. 15. Woofer Bass Reflex Duct Speaker Wire 3 4 5 1 CD-C602 ■ Remote control 11. 12. 13. 3 14. 3 15. 16. 17. 18. 19. 10. 11. 12. 13. Remote Control Transmitter LED Stop Button: (CD) Track Down/Review Button: (TUNER) Preset Down Button: (CD) Track Up/Cue Button: / (TUNER) Preset Up Button: Play/Repeat Button: Disc Skip Button Pause Button: Memory Button Clear Button Extra Bass Button: X-BASS Function Selector Buttons Power Button Volume Up/Down Buttons: / 5 / 2 3 4 6 7 8 9 10 11 12 13 RESETTING THE MICROCOMPUTER Reset the microcomputer by performing the following procedure for the cases shown below: ● To erase all of the stored memory contents, or 1 Press the POWER button to turn the power off. 2 Press and hold down the POWER button and the ■ button at the same time. Hold them down for at least 1 second. ● If the display does not function properly, or 3 Press the POWER button to turn the power on. ● The unit does not operate properly. Caution: ● The operation explained above will erase all data stored in memory including the tuner and CD presets. –4– CD-C602,CP-C602 QUICK GUIDE MINI COMPONENT SYSTEM Quick-Guide Guía rápida CD-C602 Turning the power on and off Conexión y desconexión de la alimentación Preparation for use Preparación para su uso (Left) (Izquierdo) Remote control Control remoto Remote Sensor Sensor remote (Right) (Derecho) POWER (Left) (Izquierdo) (Right) (Derecho) Red Rojo Black Negro FRONT SPEAKERS REAR SPEAKERS 15 Red Rojo Black Negro 8" - 20' (0.2m - 6m) 0,2m - 6m ● 2 “AA” batteries ● Dos pilas “AA” RATED SPEAKER IMPEDANCE: 6 OHMS MIN 12 OHMS MIN . RIGHT LEFT RIGHT LEFT 15 POWER Wire with the white line Cable con la línea blanca 1 2 3 ● AM Loop Antenna ● Antena de cuadro de AM ● Batteries are not included. ● Las pilas no están incluidas. ● FM Antenna ● Antena de FM CD playback Reproducción de discos compactos ● AC 120 V, 60 Hz ● 120 V de CA, 60 Hz OPEN /CLOSE FUNCTION OPEN /CLOSE ● “Cd” will appear in the display ● “Cd” aparecerá en el visualizador ● Label facing up ● Etiqueta hacia arriba Recording from CDs Grabación de discos compactos FUNCTION ● Load the disc to be recorded. ● Introduzca el disco que va a grabar. Precaution Precaucíon RECORD STOP/EJECT / ● The sound level at a given volume setting depends on a combination of speaker efficiency, location and many other factors. It is advisable to avoid exposure to high volume levels, which occur while turning the unit on with the volume control setting up high, or while continually listening at high volume levels. ● El nivel de sonido en una posición de volumen fijado depende de una combinación del rendimiento de las altavoces, la posición y muchos otros factores. Es aconsejable evitar un aumento de volumen. Esto se produce, por ejemplo, al conectar el aparato con el volumen puesto en una posición alta. Evite continuar la audición prolongada a altos niveles de sonido. STOP/EJECT / TAPE 1 ● “Cd” will appear in the display ● “Cd” aparecerá en el visualizador ● CD recording starts. ● La grabación de CD empieza. Tape playback Reproducción de cintas FUNCTION STOP/EJECT / STOP/EJECT / PLAY TAPE 1 ● “Tape” will appear in the display ● “Tape” aparecerá en el visualizador ● Only discs bearing the logo as shown can be played in this unit. ● En este aparato sólo pueden reproducirse los discos que tengan el logotipo mostrado. Sound control Control del sonido TAPE 2 ● Volume ● Volumen Radio operation Funcionamiento de la radio VOLUME UP VOLUME X-BASS DOWN FM STEREO ST MHz FM MONO TUNING FUNCTION TUNING VOLUME UP MHz ● “Tuner” will appear in the display ● “Tuner” aparecerá en el visualizador TINSZ0394AWZZ BAND ● Extra-BASS ● Graves extra X-BASS AM X-BASS kHz DOWN Printed in Malaysia Impreso en Malaysia A9812.HK –5– CD-C602,CP-C602 DISASSEMBLY CD-C602 Caution on Disassembly Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure excellent performance: 1. Take cassette tape and compact disc out of the unit. 2. Be sure to remove the power supply plug from the wall outlet before starting to disassemble the unit. 3. Take off nylon bands or wire holders where they need to be removed when disassembling the unit. After servicing the unit, be sure to rearrange the leads where they were before disassembling. 4. Take sufficient care on static electricity of integrated circuits and other circuits when servicing. Top Cabinet (A1)x2 ø3x12mm Front Panel Hook (B3x1) REMOVAL PROCEDURE FIGURE 1 Top Cabinet 1. Screw ..................... (A1) x4 2. Hook ....................... (A2) x3 6-1 2 Side Panel (Left/Right) 1. Screw ..................... (B1) x4 2. Screw ..................... (B2) x2 3. Hook ....................... (B3) x2 6-1 3 CD Tray Cover/ CD Player Unit 1. Turn on the power supply, open the disc tray, take out the CD tray cover, and close. (Note 1) 2. Hook ....................... (C1) x3 3. Hook ....................... (C2) x2 4. Socket .................... (C3) x4 6-2 Back Board 1. Screw ..................... (D1) x3 6-2 5 Main PWB/ Display PWB 1. Screw ..................... (E1) x10 2. Hook ....................... (E2) x2 3. Socket .................... (E3) x6 7-1 Front Panel 1. Screw ..................... (F1) x2 2. Hook ....................... (F2) x5 7-1 7 Tape Mechanism 1. Open the cassette holder. 2. Screw...................... (G1) x6 7-2 8 Turntable 1. Screw ..................... (H1) x1 2. Stabilizer ................ (H2) x1 7-3 9 Disc Tray 1. Screw ..................... (J1) x2 2. Guide ..................... (J2) x2 7-3 10 CD Changer Mechanism 1. Screw ..................... (K1) x4 7-4 1. Screw ..................... (L1) x1 Hook Back Board (B3x1) Side Panel (B2)x1 (B1)x2 (Right) ø3x12mm ø3x12mm Side Panel (Left) Figure 6-1 Hook (C1)x3 CD Tray Cover Pull Disc Tray CD Player Unit 6 CD Mechanism (B1)x2 ø3x12mm Hook (C2)x1 4 11 (A1)x2 ø3x12mm (B2)x1 ø3x12mm CD-C602 STEP Hook (A2x3) 2 1 Hook (C2)x1 Pull Front Panel (D1)x3 ø3x10mm 7-4 (C3)x4 Back Board Note 1: How to open the change manually. 1. Then, turn fully the lock lever in the arrow direction through the hole on the loading chassis bottom in this state. After that, push forward the CD player base. (Fig. 6-3) 2. After removing the connector for the optical pickup fromthe connector wrap the conductive aluminium foil around the front end of connector so as to protect the optical pickup from electrostatic damage. Main PWB Figure 6-2 Lock Lever Figure 6-3 –6– CD-C602,CP-C602 Shift Lever Display PWB Hook (E2)x2 (E1)x8 ø3x10mm PWB Spacer (L1) x1 ø2.6 x10mm Front Panel (E1)x1 ø3x10mm (E3)x5 (K1) x4 ø3 x12mm CD Changer Mechanism PWB Spacer CD Player Base (E1)x1 ø3x10mm Hook (F2)x1 (E3)x1 Main PWB Hook (F2)x4 (F1)x2 ø3x10mm Figure 7-1 Be careful when installing the CD changer mechanism. Install the CD changer mechanism on the CD player base after the shift lever has been set in the highest position. Figure 7-4 CP-C602 STEP 1 REMOVAL Front Speaker Front Panel Tape Mechanism CD Mechanism PROCEDURE CP-C602 (G1)x6 ø3x10mm FIGURE 1. Net .......................... (A1) x1 2. Duct Panel .............. (A2) x1 3. Screw ...................... (A3) x4 Speaker Box Cassette Holder (Left/Right) Open Figure 7-2 (A1) x1 (H1) x1 ø3 x10mm (H2) x1 (A2) x1 Washer Driver should be pried away from Speaker Box. Driver Turntable Direction of handle Figure 7-5 Speaker Box Woofer Disc Tray (J1) x1 ø3 x10mm (A3) x4 ø4x12mm (J2) x1 CD Player Unit (J1) x1 ø3 x10mm (J2) x1 Figure 7-6 Figure 7-3 –7– 7-5 7-6 CD-C602,CP-C602 REMOVING AND REINSTALLING THE MAIN PARTS CD MECHANISM SECTION Perform steps 1, 2, 3, and 8 ~ 11 of the disassembly method to remove the CD mechanism. How to remove the turntable up/down/loading motor (See Fig. 8-1) Turntable Up/Down/ Loading Motor 1. Remove the screws (A1) x 2 pcs., to remove the turntable up/down/loading motor. Motor PWB (A1) x2 ø2.6 x5mm Figure 8-1 How to remove the pickup (See Fig. 8-2) (B1) x2 ø2.6 x6mm 1. Remove the screws (B1) x 2 pcs., to remove the shaft (B2) x 1 pc. 2. Remove the stop washer (B3) x 1 pc., to remove the gear (B4) x 1 pc. 3. Remove the pickup. (B3) x1 Note: After disconnecting the optical pickup connector wrap the front end of connector in conductive aluminum foil so as to prevent damage to the optical pickup by static electricity. Pickup (B2) x1 CD Mechanism (B4) x1 Figure 8-2 –8– CD-C602,CP-C602 ADJUSTMENT MECHANISM SECTION TUNER SECTION • Driving Force Check Torque Meter fL: Low-range frequency fH: High-renge frequency • AM IF/RF Signal generator: 400 Hz, 30%, AM modulated Specified Value Play: TW-2412 Tape 1: Over 100 g Tape 2: Over 50 g Test Stage Frequency Frequency Display IF 450 kHz 1,720 kHz Band Coverage — 530 kHz (fL): T333 *2 1.1 ± 0.1 V Tracking 990 kHz 990 kHz (fL): T331 • Torque Check Torque Meter Specified Value Tape 1 Tape 2 Play: TW-2111 30 to 60 g. cm 30 to 60 g.cm Fast forward: TW-2231 80 to 135 g.cm — Rewind: TW-2231 80 to 135 g.cm — Normal speed MTT-111 Adjusting Point Specified Value Volume in motor 3,000 ± 30 Hz *1 *1. Input: Antenna (CNP301), Output: TP302 *2. Input: Antenna (CNP301), Output: TP301 • Tape Speed Test Tape Setting/ Instrument Adjusting Connection Parts T351 *1 • FM RF Signal generator: 1 kHz, 22.5 kHz dev., FM modulated Instrument Connection Test Stage Frequency Frequency Display Speaker terminal (Load resistance: 4 ohms) Instrument Connection Serring/ Adjusting Point Band Coverage — 87.50 MHz L303(fL): 1.3 V ± 0.1 V RF 98.00 MHz 98.00 MHz L302 (10-30 dB) *1 *2 *1. Input: Antenna (CNP301), Output: TP301 *2. Input: Antenna (CNP301), Output: Speaker terminal TAPE MECHANISM • FM Detection Signal generator: 10.7 MHz, FM sweep generator Test Stage Volume in motor Frequency Frequency Display AM Band Coverage fL AM IF T351 98.00 MHz T352 IF 98.00 MHz T301(Turn Input: Pin 1 of the core of IC301 transformer Output: TP302 T352 fully counterclookwise.) 10.7 MHz Frequency T333 98.00 MHz (60 dB) + TP301 T352 FM Detection TP302 T331 L303 T301 FM IF L302 Frequency Display 98.00 MHz Adjusting Parts VR351* Instrument Connection Pin 13, Pin 21 and ground of IC351 * Adjust for 76 kHz ± 200 Hz. R319 21 C360 C364 VR351 VCO IC351 13 Input: Pin 1 of IC301 Output: TP302 • VCO Frequency FM Band Coverage fL TP303 Instrument Connection Detection 10.7 MHz Figure 9-1 ADJUSTMENT POINTS AM Tracking fL Adjusting Parts 1 IC301 CNP301 FM/AM ANTENNA TERMINAL Notes: After preparing the test circuit shown in Fig 9-3, connect the Pin 13 , Pin 21 and ground of the IC351 with test circuit, and measure the Value. At this time, apply a standard unmodulated signal input and adjust the VCO. Pin 13 of IC351 G FM RF L301 Pin 21 of IC351 D FET : 2SK19 or 2SK54 TO FREQUENCY COUNTER S 10 kohm MAIN PWB Figure 9-3 Figure 9-2 ADJUSTMENT POINTS –9– CD-C602,CP-C602 CD SECTION CD TEST MODE Since this CD system incorporates the following automatic adjustment function, when the pickup is replaced, it is not necessary to readjust it. Since this CD unit does not need adjustment, the combination of PWB and laser pickup unit is not restricted. IL is not performed. • Automatic adjustment item 1. Focus offset (Fig. 10-1) 2. Tracking offset (Fig. 10-2) 3. E/F balance (tracking error balance) (Fig. 10-3) 4. RF level AGC function (HF level: constant) 5. RF level automatic follow-up of the tracking gain When the PLAY and POWER buttons are pressed at the same time in OFF MODE, the set will enter CD TEST MODE ↓ "CD TEST" of LCD will light up. ↓ The pickup can be moved by using the ( ) or ( ) button. → Press PLAY button ↓ LASER ON Press PLAY button ↓ FOCUS SERVO ON This automatic adjustment is performed each time a disc is changed. Therefore, each disc is played back using the optimal settings. Press PLAY button ↓ TRACKING ON THE STOP SERVO OFF PLAY Display "CD 01 0:00" 0.1s 0.50 V IC1 20 FE FOCUS OFF-SET ADJUST 0.1s 0.50 V IC1 7 TE Press PLAY button ↓ TRACKING ON THE STOP SERVO OFF PLAY TRACKING OFF-SET 1 ADJUST ↓ STOP Press PLAY button "CD TEST" will display 2 Cancel method: POWER OFF Figure 10-1 LCD display: After the PLAY or APMS MEMORY button has been pressed, the track No. and time only will appear (valid). The other items are optional. Enlarged View 10ms 0.50 V IC1 20 FE Note: The pickup can be slid using the while in the stop mode. or button only ALL CLEAR AND RE-START FUNCTION 10ms 0.50 V IC1 7 TE When the STOP and POWER buttons are pressed to turn on the power, the entire internal memory will be cleared and the mechanism will run from address 0. All of the tuner presets, APMS, TOC and disc numbers which were last stored in memory will be cleared, and the tuner, changer mechanism and all of the other items will be initialized. TRACKING OFF-SET 1 ADJUST 2 Figure 10-2 TRACKING/ ERROR BARANCE 1 ADJUST 200 ms 1V/diV IC 1 15 TO 200 ms 1V/diV IC 1 7 TE 2 Figure 10-3 – 10 – CD-C602,CP-C602 NOTES ON SCHEMATIC DIAGRAM • Resistor: To differentiate the units of resistors, such symbol as K and M are used: the symbol K means 1000 ohm and the symbol M means 1000 kohm and the resistor without any symbol is ohm-type resistor. Besides, the one with “Fusible” is a fuse type. • Capacitor: To indicate the unit of capacitor, a symbol P is used: this symbol P means micro-micro-farad and the unit of the capacitor without such a symbol is microfarad. As to electrolytic capacitor, the expression “capacitance/withstand voltage” is used. (CH), (TH), (RH), (UJ): Temperature compensation (ML): Mylar type (P.P.): Polypropylene type • Schematic diagram and Wiring Side of P.W.Board for this model are subject to change for improvement without prior notice. REF. NO DESCRIPTION • The indicated voltage in each section is the one measured by Digital Multimeter between such a section and the chassis with no signal given. 1. In the tuner section, ( ) indicates AM < > indicates FM stereo 2. In the main section, a tape is being played back. 3. In the deck section, a tape is being played back. ( ) indicates the record state. 4. In the power section, a tape is being played back. 5. In the CD section, the CD is stopped. • Parts marked with “ ”( ) are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. POSITION REF. NO SW1 OPEN/CLOSE ON—OFF SW705 FAST FORWARD ON—OFF SW2 MECHA UP ON—OFF SW706 REWIND ON—OFF SW3 DISC NUMBER ON—OFF SW707 OPEN/CLOSE ON—OFF SW4 PICKUP IN ON—OFF SW708 STOP ON—OFF SW605 TAPE 1 MAIN ON—OFF SW709 DISC SKIP ON—OFF SW606 TAPE 2 MAIN ON—OFF SW710 X-BASS ON—OFF SW607 TAPE 1 RECORD ON—OFF SW711 FUNCTION ON—OFF SW608 TAPE 1 PLAY ON—OFF SW712 BAND ON—OFF SW701 POWER ON—OFF SW714 MEMORY ON—OFF SW702 VOLUME UP ON—OFF SW715 TUNING UP ON—OFF SW703 VOLUME DOWN ON—OFF SW716 TUNING DOWN ON—OFF SW704 PLAY ON—OFF FRONT VIEW FRONT VIEW E C B (S)(G)(D) (1) (2) (3) B C E (D)(G)(S) (3) (2) (1) 2SC2389 SE KRA102 M KRA109 M KRC102 M KRC104 M KTA1266 GR KTA1271 Y KTC3194 Y KTC3199 GR KTC3203 Y DESCRIPTION 2SD2012 Y Figure 11 TYPES OF TRANSISTOR – 11 – 1 2 3 SVC211C SVC348S POSITION CD-C602,CP-C602 WAVEFORMS OF CD CIRCUIT STOP FOCUS 1 PLAY SERCH 6 1 5ms 0.50 V IC1 20 FE 7 1 8 1 12 5ms 5.0 V IC1 54 DRF 9 1 3 0.5ms 10.0 V IC1 33 0.5ms 10.0 V IC1 32 0.5ms 0.50 V IC1 14 0.5ms 1.00 V IC1 7 JP+ JP- JP TE 1 CUE 3 1 0.5ms 1.00 V IC1 41 HF PLAY 10 1 4 1 0.5ms 5.0 V IC1 4 HFL 5 1 0.5ms 5.0 V IC1 36 TES 3 1 0.5ms 1.00 V IC1 41 HF 4 1 0.5ms 5.0 V IC1 4 HFL 5 1 0.5ms 5.0 V IC1 36 TES 6 1 50ms 10.0 V IC1 33 JP+ NORMAL DISC TN0=01 20ms 1.00 V IC1 27 SPO 1 2 3 20ms V 11 1 2.00 IC2 12 CLV+ REVIEW 8 1 50ms 10.0 V IC1 32 JP50ms 0.50 V IC1 14 JP 9 1 50ms 1.00 V IC1 7 TE 7 1 6 1 7 1 8 1 9 1 0.5ms 10.0 V IC1 33 0.5ms 10.0 V IC1 32 0.5ms 0.50 V IC1 14 0.5ms 1.00 V IC1 7 50ms 1.00 V IC1 27 SPO 3 50ms V 11 1 2.00 IC2 12 CLV+ CUE PLAY TCD-712 5s 100mV IC1 29 SLD JP+ JP- JP 1 TE 8 1 9 1 50ms 1.00 V IC1 7 TE 7 1 10 1 2 12 1 50ms 10.0 V IC1 33 JP+ 50ms 10.0 V IC1 32 JP50ms 0.50 V IC1 14 JP 6 1 PLAY TCD-712 (140mm) TN0=01 1 REVIEW 12 1 0.5s 100mV IC1 29 SLD 1 – 12 – CD-C602,CP-C602 TO MAIN/ POWER SECTION CHANGER MECHANISM SW1 SW2 SW3 SOLM2 OPEN/ MECHA DISC SOLENOID CLOSE UP NUMBER M - + 7 Q93 D81 37 38 39 40 36 41 LVDD RVDD /RES 36 LVDD 23 VDD +B 4.3V 58 +B 5V 32 DRF 54 SL+, SL–, DRF 50 49 44 43 40 SW4 PICKUP IN +5V ~ 20 61 ~ JP4M 1 9 10 12 JP- DEF1 EFMO EFMIN CLV+ 45 XIN XL1 16.9344MHz CLK DEF SLI SLC CV+ 44 XOUT DEF, CLK, CL, DAT, CE, DRF CQCK 57 IC2 COIN 56 LC78622N SQOUT 55 RWC 54 SERVO/SIGNAL WRQ 53 CONTROL 6 VVDD 5 ISET ~ +B 5V 28 LCHO LVSS RVSS RCHO CONT1 24 43 XVDD 41 RVDD CONT5 +B 4.3V ~ CL 51 LASER DRIVER 64 VCC1 LDO FIN2 FIN1 E F +B 4.3V 62 1 2 3 4 17 20 DRF 54 SL+ 31 SL- 30 32 23 22 SLD 29 SPO 27 FD 16 TO 15 14 5 8 ~ IC1 LA9241M SERVO AMP. 6 7 13 12 M LASER POWER CONTROL M2 SLED MOTOR TRACKING COIL PICKUP UNIT Figure 13 BLOCK DIAGRAM (1/3) – 13 – FOCUS COIL 29 IC5 M56748FP FOCUS/ TRACKING/ SPIN/SLIDE DRIVER Q1 ALPC 11 26 ~ 1 SWITCHING 9 ~ 6 Q91 ~ 2 SOLENOID DRIVER ~ IC91 TA7291S LOADING MOTOR DRIVER ~ 3 TO DISPLAY SECTION L-CH OUT AUDIO GND R-CH OUT +12V DRIVER +5V (µ COM) +5V (SERVO) SQ OUT CO IN CQCK DRF RWC WRQ DSP_RES DISC NO. SL – SL + DRF PU-IN M3 TURNTABLE UP/DOWN/ LOADING MOTOR M M1 SPINDLE MOTOR 24 25 30 31 CD-C602,CP-C602 IC301 TA7358AP FM FRONT END +B5 AM IF 3 FM +B 17 7 16 DET OUT 1 2 3 21 FM +B ST IND AM AM AM 22 23 24 AM +B FM OSC. FM IF FM RF 20 FM DET FM IF DET. /FM MPX. /AM IF 8 6 AM OSC L303 T301 AM RF IN VD302 L302 5 AM IF IC351 LA1805 TUN IND VD301 15 CNP301 FM/AM ANTNNA TERMINAL AM ANT. Q352 FM +B 11 L OUT L-CH 9 R-CH 10 R OUT VCO 13 VR351 VCO AM OSC. T333 X IN B01 Q381 D381 16 15 11 10 IC381 LC72131 PLL CONTROLLER 3 4 5 6 CE FM 7 22 CL 1 X OUT 20 A OUT VT FM IN X381 4.5MHz B04 RF AMP. AM IN Q302 VD331-2 IO1 VD331-1 DI T331 VOLTAGE REGULATOR VDD 17 ZD381 VSS 21 DO AM LOOP ANTENNA 1 2 3 1 FM IF IN MONO/ST CF302 L301 AM IF IN AM MIX OUT FM/AM FM IF 10.7MHz 9 ST 8 7 MPX IN 5 STEREO 6 GND FM BAND PASS FM FILTER ANTENNA 4 3 T352 ST FM IN 1 SWITCHING FM DET CF351 T351 VCC FM IF IN OSC FM-M/ST B.A MIX RF +B5 SWITCHING CD SECTION M601 TAPE MOTOR M +B4 D201 D202 SW606 TAPE2 MAIN T2 PLAY SW605 TAPE1 MAIN T1 PLAY SW608 TAPE1 PLAY TU T TA IC201 AN7345K PLAYBACK AND RECORD/PLAYBACK AMP. TAPE1 RECORD/ PLAYBACK L-CH R-CH HEAD REC. P.B. SWITCHING Q201 T2 L Q206 +B5 VCC 13 1 P. B T2 R 24 T1 L L R 2 ~ TAPE2 PLAYBACK L-CH HEAD R-CH L OUT 4 21 R OUT T1 R 23 L NF 3 R NF 22 POP REDUCE 6 L REC 9 R REC T1/T2 T1/T2 19 18 L REC IN 7 8 REC 16 R REC IN Q210 Q213 17 REC MUTING Q207~ Q209 ALC Nor/ CrO2 15 ALC 12 GND 10 11 ALC CUT Q214 Q211 SWITCHING +B4 SWITCHING SW607 TAPE1 RECORD Q212 L203 ERASE HEAD REC BIAS OSC Figure 14 BLOCK DIAGRAM (2/3) – 14 – CD-C602,CP-C602 LCD701 LCD DISPLAY COM 0 ~ COM 3 25 ~ 22 S0 ~ S20 21 ~ 1 LCD BIAS 25 BIAS 29 KI0 26 VLC0 21 ~ 1 ~ 9 69 ~ 80 24 COM 0 ~ COM 3 COM OUT ~ ~ KEY MATRIX SEG0 ~ SEG20 SEG OUT 32 KI3 SW701 ~ SW712 SW714 ~ SW716 RESET RESET 68 Q701 KEY IN ~ ~ 34 KO0 37 KO3 DO DI CE CL POWER FAIL DETECTOR IC701 IX0217AW SYSTEM MICROCOMPUTER 63 65 66 64 D703 Q702 Q703 SYSTEM STOP 39 +B6 DSP RST POWER VDD(+5V) 40 41 43 51 52 54 T1/T2 POWER CONT. WRQ DISC NO DRF 42 61 62 67 T2 PLAY T1 PLAY REC REMOTE SENSOR REMOCON 38 IC 57 VDD X1 58 1 RX701 X2 59 2 3 XL701 4.19MHz CE DI CL IC601 LA4597 POWER AMP. 6 2 8 1 7 25 24 23 CD L 21 L1 IC431 LC75394E AUDIO PROCESSOR CD R 28 R1 TUNER L 19 L2 TUNER R 30 R2 TAPE L VOLUME GRAPHIC EQUALIZER 17 L3 LVR OUT 58 L-IN R-IN 3 VCC 56 63 50 26 27 12 37 11 38 RF1C3 LF1C3 RF1C2 LF1C2 RF1C1 LF1C1 AVSS VSS RVREF LVREF VREF L SELO R SELO 14 35 L R L-OUT JK601 HEADPHONES 4 GND L OUT SWITCHING Q601 RVR OUT 55 R VDD 57 MUTE 10 12 R-OUT 5 NF TAPE R 32 R3 NC NC 16 33 L R REF Q602 VOLTAGE REGULATOR SPEAKER SWITCH FRONT SO601 SPEAKER TERMINALS +B5 REAR 10 39 PT901 POWER TRANSFORMER D901 ~ D904 VOLTAGE REGULATOR +B4 +12V (MECHA) +B5 +12V (ANALOG) Q921 Q922 Q923 SO901 AC SOCKET T.F TO CD SECTION +B6(5V) VOLTAGE REGULATOR AC POWER SUPPLY CORD AC 120V 60Hz 3 IC921 1 2 Figure 15 BLOCK DIAGRAM (3/3) – 15 – CD-C602,CP-C602 R1 1K +B TR+ 2 TR+ FO+ 3 FO– 4 FO+ 7 C37 220/6.3 C38 0.01 R29 1K R15 47K R41 4.7K CL CLK DEF DAT R16 1.5K SLOF – – VREF C33 0.001 RFSM C30 2.2P 41 CV+ 40 CV– SLOF 39 HFL 37 TES 36 TOFF TGL JP+ 35 SL+ JP– – SL– REF SLD SLEO SPO C34 0.033 (ML) RFS– 42 + – – + R23 1.2K R19 39K + – LATOH JP+ JPCLO OR R38 33K R36 47K R37 47K R33 5.6K C32 27P R34 1K R32 56K R35 C31 470 0.0027 L HF TP1 38 34 33 29 30 31 32 C19 47/25 R22 6.8K 44 JP– + – REF SP– REF – R17 82K RF 24 25 26 27 28 C16 0.001 C14 0.01 R39 22K R40 22K FE– FE FA FA– R14 10K CE FSS DRF REF1 VR LF2 PHI BHI VCC2 CV+ R25 R24 1.2K 10K R30 18K C53 220 R27 220K R26 220K GND FO– TR– 6 8 C12 330P R12 C13 15K 0.1(ML) 20 21 22 23 45 C11 0.1(ML) GND 5 LD 18 19 17 REF REF CV– C17 0.47/50 F TR– 1 PD FSC JP REF FOSTA + – TO GEN –+ REF + + – GEN REF + – FD– R13 33K R28 1K VR REF REF – C75 100P 1/16 16 FD 2200p 5 D B VCC + – SLI SLC 43 + – + + TGL1 – – REF THDL GL FSTA REF JP THD 1M 3 4 E A 2200p 1M 2 K IC1 LA9241M 8/12CM SERVO AMP.SLOF + 1 FSTA + PICKUP UNIT VCR – R7 1K DGND LASER S.Q.R C7 R6 0.1/50 100 TH 10 C9 C8 0.047(ML) 0.068 NC + 11 (ML) 12 GEN TD– R9 R8 C10 27K 12K 180P TD R11 13 3.3K 14 JP 15 TO + C DRF REF 9 SCI C50 0.1(ML) 46 FSC CE REF CL 2FREQ C20 0.0033 C6 0.033 (ML) REF R5 6.8K FOSTA TOSTA SLOF R4 C5 2.2K 0.033(ML) + – EFBAL HFL SLOF + TE C4 0.001 R2 100K R3 15K NC 48 TBC 47 C18 1/50 C3 0.1/50 DEF REF 5 SPI 5 SPG F 5 + – – + 10K 56K 4 C15 0.0047 3 4 R20 R21 3 55 54 53 52 51 50 49 REF FE1 2 56 + – AGND SP 2 1 + E 2 A 3 B 4 FIN2 RF – REF + 2 FIN1 – FE1 – REF + E REF 3 F VCR 4 REF – VCR TB 5 – VCR TE– REF – 6 TE 7 REF + – + – REF TESI 8 57 58 + 1 59 + 1 - + K 1 61 60 LDO VCC1 + LDS CNP1 CNS1A CNS1B B 62 64 63 C45 4.7/50 C24 1/50 R42 560 2.78V C39 0.47/50 C25 0.01 C40 0.33/50 A C35 0.1/50 LASER DRIVER Q1 R43 KTA1266 GR 4.15V 12 1.84V C2 47/25 C1 0.01 R10 82K C21 1/50 D2 1SS133 ACTUATOR 1 2 3 4 5 6 7 F 8 TR– TR+ FO+ FO– GND PD VR LD CNP2 CNS2B CNS2A E NC 36 2 NC 35 3 NC NC 34 4 NC NC 33 5 1 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 6 TR– 7 TR+ 8 FO+ 9 FO– 10 GND PD VR LD C44 330/10 IC5 M56748FP FOCUS/ TRACKING/ SPIN/SLIDE DRIVER 32 30 29 28 27 11 26 12 25 13 24 14 23 15 22 16 NC 21 17 20 18 NC +5V 31 R31 10K +B NC 19 +B 6 5 5 + 4 4 4 4 – 3 3 3 3 2 2 2 2 1 1 1 1 CNP3 6 5 CNP3A 6 5 SP+ SP– SL+ SL– R54 1K PU-IN 1 H • The numbers 1 to 12 are waveform numbers shown in page 12. • NOTES ON SCHEMATIC DIAGRAM can be found on page 11. 1 2 3 4 Figure 16 SCHEMATIC DIAGRAM (1/9) – 16 – 5 6 SL– SW4 PICKUP IN M 6 – + SL+ M2 SLED MOTOR M PUIN M1 SPINDLE MOTOR CNS3A G CNS3B CD MOTOR PWB-B 2 3 CD-C602,CP-C602 MAIN PWB-A1(1/4) 1K 1K 1K +B C57 100P R60 1K C22 0.01 C55 100P CD SIGNAL C54 100P R45 R46 R47 C56 100P +B EFLG 48 SBSY 47 NC SUB-CODE 1 DEF1 2 TA1 CLV DIGITAL SERVO V/P HLF C53 220P DAC 1BIT N.C. 34 TEST4 33 EXTERNAL OUTPUT SERVO TES COMMAND TOFF 16 CLV- 1K R86 CD-LD M– R97 2.2K R98 10K 4 5 6 +B L1 0.82µH +4.3V D81 1SS133 15 D_GND R96 10K Q91 KTA1271 Y SOLENOID 0V DRIVER +5V (SERVO) TO MAIN/ POWER SECTION P18 1-F 16 AUDIO GND 11.82V R94 56 CNS4 CNP4 1 2 3 4 5 6 7 8 9 10 R92 10K +5V (µCOM) C51 0.022 D91 1SS133 SWITCHING Q93 KRC102 M 11.82V 3 0V 2 R95 1 0V 2.2K SOL GND(M) M+ M– OPEN CLOSE GND(D) DISC NO. GND(D) MECHA UP GND(D) R91 10K 9 10 TRAY MOTOR PWB-C BIM5 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 SW2 MECHA UP SOLM2 SOLENOID M3 TURNTABLE UP/DOWN/ LOADING MOTOR SW1 OPEN/CLOSE + – M 1 2 CNS5 1 2 SW3 DISC NUMBER D_GND DISC NO M_GND MOTOR GND 1K R78 7 8 C72 100P +B DSP_RES R77 RWC WRQ CQCK 3 COIN 2 DRF SL– 1 SL+ SQOUT 1K C73 100P 14 C74 100P 11.84V C91 47/25 +12V DRIVER +B +B 1 2 3 4 5 6 7 8 9 CD_L 13 R93 4.7 NC IC91 TA7291S LOADING MOTOR DRIVER C69 220P C43 100/10 R82 100 L2 27µH D_GND +B R75 1K 12 CD A GND TO MAIN/ POWER SECTION P18 1-E +B +5V C70 220P R73 4.7K +12V C52 100/10 CD-LD M+ C67 10/50 R76 1K C58 220P D2 1SS133 C59 0.022(ML) CD_R R74 4.7K TEST3 32 24 25 26 27 28 29 30 31 NC 17 18 19 20 21 22 23 C68 10/50 DIGITAL OUT EMPH NC C2F NC DOUT NC 15 TEST2 CLV+ LVSS 38 LCHO 37 LVDD 36 MUTEL NC 35 IC2 LC78622N SERVO/ SIGNAL CONTROL CONT5 14 SYNC-DETECT EFM DEMODULATE SLICE LEVEL CONTROL CONT4 13 EFMIN C71 330P 1K 12 EFMO 1K 11 VSS R89 OPEN/CLOSE R90 MECHA UP 10 FR CONT3 8 4FS DIGITAL FILTER 1K 7 9 VVDD ERROR COERECT FLAG CONTROL R88 R56 1.2K VCO CLOCK OSC CONTROL 1K 6 XVDD 43 MUTER 42 NC RVDD 41 RCHO 40 RVSS 39 ISET R87 R57 27K VVSS CONT1 CONT2 5 C42 0.047(ML) LUG1 1 027 4 FSEQ NC VDD R34 1K PCK C41 R58 0.047(ML) 680 XIN 45 XOUT 44 X-TAL GENERATOR 2KX8 RAM JP– R37 47K 3 PDO JP+ R18 3.3M XVSS 46 TGL 8 K NC XL1 16.9344MHz µ-COM INTERFACE 49 PW NC FSX NC SBCK SFSY NC RWC WRQ COIN /CQCK SQOUT 16M NC NC /RES TEST11 TEST1 /CS TEST5 4M 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 ML) 11 TO DISPLAY PWB P24 4-H 7 8 9 10 Figure 17 SCHEMATIC DIAGRAM (2/9) – 17 – 11 12 CD-C602,CP-C602 C443 0.68/50 8 7 6 5 4 3 2 NC NC NC NC NC NC NC NC L SELO NC 18 NC LIN VIN 2 62 20 NC B LTEST 59 23 CL 25 CE VDD 57 Vref 56 RVR OUT 55 26 VSS 27 AVSS RTEST 54 28 R1 RVR IN 53 RF1C3 NC NC NC NC NC NC NC RVref 50 NC RT IN R SELO NC 32 R3 RF1C2 RIN VIN 2 51 RF1C1 RT OUT 52 30 R2 RIN VIN 1 29 NC 31 NC C 49 13 CD_L CD_A_GND 15 C442 180P C440 22/16 CD_R +5V(µCOM) CD +B C436 0.047(ML) 12 RFS C 0 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 TO CD SECTION P17 12-D 10/5 LVR OUT 58 IC431 LC75394E AUDIO PROCESSOR 24 DI C434 0.047(ML) 100 LVR IN 60 C46 22 VSS C432 0.047(ML) LFS LT OUT 61 21 L1 R460 1K R461 1K R462 1K 64 LVref 63 C46 19 L2 C431 0.047(ML) 1 NC C433 0.047(ML) LF1C3 9 LF1C1 16 15 14 13 12 11 10 17 L3 LI VIN 1 C435 0.047(ML) C445 0.022(ML) LT IN C441 180P LF1C2 C439 22/16 NC R449 10K R447 3.3K A GND(D) R452 1K R448 3.3K C482 2.2/50 C444 0.68/50 R450 10K R451 1K C446 0.022(ML) C481 2.2/50 D TO DECK SECTION P21 12-F E 31 +B +12V(MECHA) +B +B TO CD SECTION P17 12-D +B +B 14 +12V(SERVO) +B +B 12V TO DISPLAY 34 PWB P24 5-A POWER_CONT +B 16 12V R922 10K 11.09V C921 0.022 (ML) +5V(µCOM) R921 2.2K 2 0V +B C92 0.02 (ML R923 22K 3.72V 3 Q922 0V 1 KRC102 M C 2 GND(µCOM) F TO CD SECTION P17 12-E GND (MECHA) +B +B CD +B C925 47/25 G +B 24 28 +12V PLAYL 27 RECL CL 26 RECR +12V ROUT GND(D) PLAYR 25 DI 22 21 20 CE 17 18 LOUT 19 TO TUNER/ TO TUNER DISPLAY SECTION SECTION P23 12-G P23 12-E P24 3-A H GND(A) GND(D) +B TO DECK SECTION P21 12-B • NOTES ON SCHEMATIC DIAGRAM can be found on page 11. 1 2 3 4 Figure 18 SCHEMATIC DIAGRAM (3/9) – 18 – 5 +12 Q921 KTA1271 Y 6 CD-C602,CP-C602 MAIN PWB-A1(2/4) FM SIGNAL 64 ef 63 C463 2 62 PLAYBACK SIGNAL C459 0.0027 C461 100/10 LFS RECORD SIGNAL 100P CD SIGNAL UT 61 N 60 C465 10/50 R601 10K N 53 UT 52 R605 120 C471 0.022 R603 C601 3.3K 0.001 R604 C602 3.3K 0.001 C460 0.0027 C606 220/25 C462 100/10 RFS – 62 20K 9 20K 11 4 ef 50 C604 100/10 R606 120 10 L 7 C603 100/10 C464 100P 2 51 + 6 1 62 13 – + 3 R 2 C609 470/16 C611 0.1(ML) R607 3.3 R609 1.2K C466 10/50 R608 3.3 C476 100/16 R612 220 R611 220 JK601 HEADPHONES C612 0.1(ML) R610 1.2K ST 54 R602 10K C607 100/10 C475 100/10 C468 10/50 UT 55 49 IC601 LA4597 POWER AMP. +B D 57 ef 56 C608 100/10 C467 10/50 UT 58 R463 220 ST 59 12 C610 470/16 8 5 D601 1SS133 +B 13.9V 2 Q601 KRA102 M SWITCHING SO601 SPEAKER TERMINALS 14V 1 3 1.26V R-CH GND L-CH GND FRONT SPEAKER R-CH R613 1K L-CH (6 ohms) 1 0V 0V 2 Q602 KRC102 M VOLTAGE REGULATOR 3 REAR R-CH GND VOLTAGE REGULATOR Q923 2SD2012 Y +B +B REAR R-CH +12V 14.09V C613 22/50 +B REAR L-CH GND C614 22/50 REAR L-CH (12 ohms ) 12.04V R927 270 (1/2W) C903 3300 D904 RL203F D902 RL203F 1 2 925 7/25 C926 0.022 7 1 1 1 1 2 2 2 2 T.F PT901 POWER TRANSFORMER CNP902 +B C901 0.047 (ML) C902 0.047 (ML) D903 RL203F CNS902 IC921 KIA7805P VOLTAGE REGULATOR 3 D901 RL203F +B CNS901 C924 470/25 ZD921 MTZJ13A C923 220/16 R925 22K R926 100 CNP901 R924 47 C922 0.022 (ML) REAR SPEAKER 3.69V SO901 AC SOCKET AC POWER SUPPLY CORD AC120V 60Hz C927 0.1 (ML) 8 9 10 Figure 19 SCHEMATIC DIAGRAM (4/9) – 19 – 11 12 CD-C602,CP-C602 MAIN PWB-A1(3/4) CNP201 2 2 1 1 R228 68K C201 0.001 3 C202 0.001 R229 33K R216 56 R207 1K R-CH R218 100K Q201~Q206:SWITCHING R223 3.9K R226 5.6K Q205 KTC3199 GR R203 6.8K R214 1K 1 2 C212 330P 2 2 R236 560 7 8 + IC201 AN7345K HIGH=T2 PLAYBACK AN + 1 0V 0.7V 0V R204 6.8K 0V R201 10K Q204 2SC2389 SE 0.7V E R215 1K 23 C213 330P 112K 22 21 R210 10K 0V C203 180P – 24 0V 0V R205 3.3K 0V 20 C221 1/50 C211 330P C217 0.033 C219 (ML) 560P R225 5.6K R219 R224 100K 3.9K R211 10K R217 56 18 6 R227 33K 17 R234 6.8K C228 0.001 3 19 C224 3.3/50 3 5 112K C 2 R232 3.3K 5 4 4 – NC 5 3 NC 0V C 2 C220 1/50 7 6 4 1 ERASE HEAD 0.7V 0V C223 0.022 R-CH 0V 0V R202 3.3K C215 47/25 D 0.7V C208 0.001 6 0V R233 6.8K C210 330P C207 0.001 Q206 KTC3199 GR 7 Q203 2SC2389 SE L-CH C204 180P RECORD/ PLAYBACK HEAD CNP202 TAPE1 CNS202 C (ML) C214 47/25 0V 0V R209 10K Q202 Q201 2SC2389 SE 2SC2389 SE C216 C218 0.033 560P R208 10K R237 3 L-CH R206 1K C227 0.001 B CNS201 TAPE2 PLAYBACK HEAD PLAYBACK SIGNAL RECORD SIGNAL R231 3.3K A GND REC M601 TAPE MOTOR G M + – 1 1 2 2 SW606 TAPE2 MAIN 3 3 4 4 SW605 TAPE1 MAIN 5 5 6 SW607 TAPE1 RECORD C246 47/25 L205 100µH D201 1N4004S +B +B SWITCHING Q207 KTA1266 GR 10.9V 10.2V D202 1N4004S +B 7 7 8 C209 0.022 (ML) +B 1 0V 2 0V 3 6.1V 11V R220 10K 1 0V 3 R213 10K Q208 KRC104 M 6 8 REC 11V R212 10K F CNP203 CNS203 REC 2 6.1V C222 22/16 0V Q209 KRC104 M SWITCHING H • NOTES ON SCHEMATIC DIAGRAM can be found on page 11. 1 2 3 4 Figure 20 SCHEMATIC DIAGRAM (5/9) – 20 – 5 11.7 Q214 KTC3199 GR 11.68V 6 CD-C602,CP-C602 R230 22K 24 RECL R259 100K 25 PLAYL 0V Q210 KTC3199 GR 0V 0V R245 10K R249 0V 10K R266 100K R236 560 C235 0.0033 D205 1SS133 C240 22/16 C241 100/10 9 GND(A) GND(D) R254 10K R247 10K R251 6.8K 15 14 13 Nor/ RIPPLE VCC CrO2 Q211 KTC3199 GR SWITCHING +B +B 56K +B R256 470 R248 10K +B R252 100K R250 47K HIGH=CHROME 56K 17 ALC ALC 10 11 GND 12 C238 1/50 C239 0.082 (ML) 16 T1/T2 C242 0.0039 (ML) + – C230 22/16 C236 0.0033 R237 560 30 7.23V BIAS OSC Q212 0.5V KTC3203 Y -1.5V R255 1K R240 100 29 R257 150 ACK AND RECORD/PLAYBACK AMP. 0.001 +B REC 45K 34 K 28 +12V 0.7V 0V C237 1/50 – + +B 0V R246 10K 8 27 RECR R258 100K 0V R265 10K R243 10K C229 22/16 Q213 KTC3199 GR REC MUTING TO DISPLAY PWB P24 4-A 0.001 C231 0.047 (ML) R239 100 0V C265 4.7/50 REC MUTING 26 PLAYR TO MAIN/POWER SECTION P18 4-H R238 10K C244 47/25 R253 12 R244 10K C232 0.047 (ML) C243 0.027 (ML) L203 330µH GND(MECHA) +B +12V (MECHA) +B +B R235 2.2K T1 PLAY T2 PLAY REC_SW R260 6.8K 2 6 TO DISPLAY PWB P24 4-A 32 33 CNS204 11.77V GR 11.68V 31 CNP204 V TO MAIN/ POWER SECTION P18 1-E +B 1 2 1 2 SW608 TAPE1 PLAY 7 8 9 10 Figure 21 SCHEMATIC DIAGRAM (6/9) – 21 – 11 12 CD-C602,CP-C602 A 7 C322 15P (CH) L302 R313 33K R312 22 R316 47 C332 0.001 C328 10/50 1 VD302 SVC211C 3 CF302 10.7MH R317 10K 2 R320 820 C321 0.022 FM IF +B FM BAND COVERAGE fL C320 0.001 C319 0.022 C323 18P R319 4.7K + R318 680 C327 100P R315 47K 2.11V D331 1SS133 C C316 0.0047 3 R314 10 FM OSC T301 FM IF 1 2 9 8 C326 0.022 6 VD301 SVC211C FM RF C313 0.0047 FM 1 GND 2 AM 3 C314 4.7P(UJ) D303 1SS133 CNP301 AM LOOP ANTENNA 4 5 C317 4.7P C318 0.001 FM ANTENNA B 3 C325 22P(CH) 2 C315 0.01 L303 L301 1 C302 6.8P C324 3.3P (UJ) C301 82P IC301 TA7358AP FM FRONT END C312 10P R311 100K FM BAND PASS FILTER 0.74V 0V RF AMP. Q302 KTC3194 Y HEAT SINK GND D AM TRACKING fL T331 +B R339 10K C344 18P (UJ) AM ANT AM OSC C333 560P T333 C339 0.047 C342 0.022 VD331 SVC348S C331 0.022 C353 10/50 E CNP302 2 1 F R331 68K AM BAND COVERAGE fL C336 22P (UJ) FM SIGNAL G AM SIGNAL +B MAIN PWB-A1(4/4) H • NOTES ON SCHEMATIC DIAGRAM can be found on page 11. 1 2 3 4 Figure 22 SCHEMATIC DIAGRAM (7/9) – 22 – 5 6 CD-C602,CP-C602 AM IF CF351 1 3 T351 +B 15 C360 3.3/50 TP302 C363 1/50 14 TP303 13 R357 1.2K C359 3.3/50 R353 1.5K VR351 6.8K(B) VCO FM DET C356 0.0022 C354 220/10 12 11 NC 2.7K R376 3.3K C374 1/50 FM-M/ST 18 17 7.58V C362 3.3/50 T352 16 DET OUT 20 19 R351 3.9K 24 23 22 21 10 R359 10K 3 Q352 KRA109 M SWITCHING 7V 2 VCO 9 1 5.5V AM/FM 8 L-CH 7 TUN IND 6 GND AM IF 5 IC351 LA1805 FM IF DET./FM MPX./AM IF R352 C357 33K 0.018 +B 4 3 FM DET FM IF AM OSC IN AM +B AM MIX AM RF 2 ST IND C393 22/16 FM +B 1 R319 4.7K C371 0.018(ML) C352 0.022 FM IF R373 2.7K R-CH C351 0.022 CF302 10.7MHz MPX-IN 3 C373 R375 3.3K C372 1/50 0.018(ML) R374 2 C358 470P C364 0.0015 (P.P) R354 47K R358 15K C355 0.022 TP301 +B R360 470 +B R OUT 17 GND(A) +B ZD381 MTZJ5.1B +B L OUT R399 10K 2 1 C384 47/25 12 NC R386 10K C383 0.022 C387 100P C385 1/50 R390 2.2K R388 1.5K B04 10 14 NC NC 9 15 AM IN NC 8 16 FM IN B01 7 17 VDD DO 6 18 PD CL 5 CE 3 21 VSS NC 2 C388 0.001 22 X OUT X IN 1 X381 4.5MHz TO MAIN/ POWER SECTION P18 2-H 18 GND(D) +B +12V 19 R392 1K R391 47K R393 1K DI 4 20 A OUT C390 12P (CH) R387 150 IO1 11 13 IO2 19 A IN +B L381 100µH R363 10K +B R395 1K SWITCHING D381 1SS133 Q381 1 KRA102 M R397 4.7K 2 12V 0V 3 12V R396 1K R394 1K CE DI IC381 LC72131 PLL CONTROLLER C391 15P (CH) CL DO 20 TO MAIN/ POWER/ DISPLAY SECTION P18 3-H P24 3-A 21 22 23 C392 0.001 +B +B 7 8 9 10 Figure 23 SCHEMATIC DIAGRAM (8/9) – 23 – 11 12 CD-C602,CP-C602 TO MAIN/POWER SECTION P18 1-E 30 34 +B GND (µCOM) +5V (µCOM) 15 POWER_CONT 29 33 T2 PLAY T1 PLAY 32 REC 23 22 DO DI CE DISPLAY PWB-A2 21 CL 20 A TO DECK SECTION P21 12-D TO DECK SECTION P21 12-G T1/T2 TO MAIN/POWER TUNER SECTION P18 3-H, P23 12-G 1K 1K 1K 1K 6.8K B R742 4.7K R764 1K PU IN DISC NO REC WRQ C709 0.01 C717 0.022 REMOTE SENSOR RX701 3 +B +B R760 100K C707 0.01 R735 1K C701 100P R701 100K 0V SW716 BAND TUNING DOWN SW703 SW707 SW711 VOLUME DOWN OPEN/ CLOSE FUNCTION TUNING SW702 SW706 SW714 RESET SW712 STOP R708 100K VDD SW708 PLAY 3 0V Q701 KRC102 M UP SW705 FAST DISC SKIP FORWARD R705 1K R706 3.3K R703 1K D701 1SS133 +B VOLUME REWIND X-BASS MEMORY UP SW701 D702 0V 1SS133 1 2 4.2V SW715 POWER C708 0.01 C706 3.3/50 L701 100µH SW704 SW710 0V +B C702 0.01 SW709 WRQ DRF DISC NO. PUIN SQOUT SL+ RWC CQCK COIN SL– DSP_RES C703 100P R702 100K 0V 0V R722 82 R758 100K R757 100K C705 100P G Q702 KTC3199 GR 0.9V R759 100K F 100K R749 1K R761 100K R704 2 ZD701 R724 MTZJ3.3B 1K R723 1K C704 100P R732 12 1 2122 23 24 25 26 27 28 29 30 3132 33 34 35 36 37 38 39 40 R707 100K D704 1SS133 C713 10/50 D703 1SS133 9 4 11 1 5 3 8 7 6 2 10 TO MAIN PWB P17 7-H H • NOTES ON SCHEMATIC DIAGRAM can be found on page 11. 1 2 3 4 Figure 24 SCHEMATIC DIAGRAM (9/9) – 24 – C710 0.01 21 COM0 1K 1K 1K 1K 1K 1K 1K 1K 1K 1K 1K 1K Q703 KTC3199 GR POWER FALL DETECTOR RWC 39 SYSTEM STOP SL+ SQOUT 40 DRF +B R731 R730 R718 R728 R727 R726 R717 R729 R720 R719 R743 R725 C716 100/10 +B R716 10K R721 100 POWER NC IC701 POWER IX0217AW DSP RST SL– SYSTEM COIN MICROCOMPUTER CQCK R736 150 C714 0.022 R715 10K CE DI CL DO RESET T1/T2 61 T2 PLAY D705 1SS133 +B 4.3V NC NC NC 62 T1 PLAY XL701 4.19MHz R714 10K NC NC NC NC NC NC NC NC 79 SEG10 80 SEG11 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 R737 470 R762 10K SEG16 SEG17 SEG18 SEG19 SEG20 IC XT2 NC XT1 NC VDD(+5V) R712 10K C712 47/25 SEG14 SEG15 R734 1K SPAN 60 X2 59 X1 58 R711 10K E SEG12 SEG13 KI0 KI1 KI2 KI3 VSS KO0 KO1 KO2 K03 REMOCON COM 0 COM 1 COM 2 COM 3 +B 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 VLC0 NC VLC1 NC VLC2 S11 S12 S13 S14 S15 S16 S17 S18 S19 S20 R744 4.7K +B SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0 S10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 COM2 COM3 BIAS S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 COM1 D LCD701 C LCD DISPLAY R738 R741 R739 R740 R765 R745 4.7K 5 6 CD-C602,CP-C602 SW3 DISC NUMBER SW607 TAPE1 RECORD CNS5 2 1 2 1 SW605 TAPE1 MAIN SW606 TAPE2 MAIN M601 TAPE MOTOR A - SW2 MECHA UP 8 7 6 5 4 3 2 1 TO MAIN PWB CNP203 P27 7 - A M3 TURNTABLE UP/DOWN/ LOADING MOTOR CNS4 TO MAIN PWB CNP4 P27 8 - H 6 - GY VL BL GR YL OR RD BR SOLM2 SOLENOID BIM5 B OR BR WH GY WH GY WH GY WH RD 10 9 8 7 6 5 4 3 2 1 + COLOR TABLE 1 BR TRAY MOTOR PWB-C PT901 POWER TRANSFOMER PICKUP UNIT C 1 + CNS203 SW1 OPEN/CLOSE BROWN RD(R) RED OR ORANGE YL YELLOW GR GREEN BL BLUE VL VIOLET GY GRAY WH(W) WHITE BK BLACK PK PINK 5 1 8 D BR CNS902 CNS901 CNS1B 1 2 3 4 5 TO MAIN PWB CNP901 P26 5 - A CNS2B BL PK WH YL BK 1 2 3 4 5 6 7 8 BL TO MAIN PWB CNP902 P26 3 - A 1 2 1 RD 2 RD WH GY WH GY WH GY WH BR SW608 TAPE1 PLAY BK WH PK YL BL E CNS1A 1 2 3 4 5 CNS2A 1 2 3 4 5 6 7 8 CNP1 P26 5 - H TO MAIN PWB CNP2 P26 6 - H TO MAIN PWB 2 1 CNP204 P27 9 - A TO MAIN PWB - M1 SPINDLE MOTOR CNS204 BK BK + F TAPE 2 SW4 PICKUP IN TAPE 1 PLAYBACK HEAD ERASE HEAD RECORD/PLAYBACK HEAD + WH PK BK YL WH BK WH M2 SLED MOTOR RD BK BK - CNP3A 1 2 3 4 5 6 G GY GY GY CD MOTOR PWB-B 3 2 1 7 6 5 4 3 2 1 CNS201 CNS3B RD WH GY WH GY WH BK BK YL WH RD BK WH WH RD BK 1 2 3 4 5 6 CNS202 1 2 3 4 5 6 CNS3A H CNP201 P27 7 - A TO MAIN PWB 1 CNP202 P27 9 - A TO MAIN PWB 2 CNP3 P27 7 - H TO MAIN PWB 3 4 Figure 25 WIRING SIDE OF P.W.BOARD (1/3) – 25 – 5 6 CD-C602,CP-C602 FROM POWER TRANSFORMER P25 6-D FROM POWER TRANSFORMER P25 3-D CNS902 CNS901 M 1 IC921 1 2 3 5 10 C445 35 30 33 32 25 15 R450 R245 R240 C222 R448 40 IC431 C440 C58 20 C436 16 17 11 R C41 C34 R36 R357 C38 C40 R42 R8 R11 C364 R2 R3 C3 C362 1 Q1 R358 R353 MAIN PWB-A1 2 3 4 Figure 26 WIRING SIDE OF P.W.BOARD (2/3) – 26 – C10 D381 R396 9 CNS1A CNS2A P25 1-F FROM PICKUP UNIT P25 2-F FROM PICKUP UNIT 8 1 • The numbers 1 to 12 are waveform numbers shown in page 12. 2 C9 C7 8 7 6 5 4 3 2 1 R394 R393 R9 CNP3 1 2 3 4 5 6 CNP2 R395 R398 C75 R6 CNP1 1 2 3 4 5 X381 C390 C385 R386 R5 C4 C8 C6 R388 R363 R390 C387 R392 R391 C392 10 C5 11 10 9 8 7 6 5 4 3 2 1 C301 5 B C E R4 12 13 141516171819 20 21 22 IC381 C35 R359 C363 C374 C371 C358 C360 C357 R352 C359 C354 C313 L301 1 2 3 C24 C388 C318 60 64 1 R43 R354 C383 C314 TP302 R397 R311 55 R1 C25 VCO R41 4 TP303 VR351 C384 Q381 C316 D303 L302 L381 T301 C315 C320 R313 VD301 R360 C324 C325 R387 C321 ZD381 R314 C323 R399 C322 C317 VD302 C319 C302 C312 9 8 7 6 5 4 3 2 1 C355 TP301 R317 R318 IC301 C326 R312 T352 R320 L303 C328 G C352 2 B C E FM/AM LOOP ANTENNA R351 C356 Q302 CNP301 R316 R319 1 C2 C1 IC351 24 23 22 21 2019 18 17 16 15 14 13 CNP302 C327 C74 3 2 1 1 2 3 4 5 6 7 8 9 10 11 12 CF302 C391 C331 C353 C332 D331 T331 R315 1 2 3 C39 Q352 C393 1 2 3 F C372 C336 C351 C373 R339 C342 R331 C339 T333 C344 T351 CF351 1 2 3 C37 C50 VD331 R37 C33 C333 1 2 3 C42 R58 C432 R462 C431 R460 R461 C434 C441 C433 C435 R375 R373 R374 R376 E R18 R38 R449 R447 R451 C481 1 R237 R258 C446 C460 C462 45 R46 64 1 C442 50 55 60 C482 R452 C459 C463 C465 C461 C613 C444 C464 49 48 C439 H R265 R249 C237 R231 R233 C471 C466 C443 AM C235 R236 R239 C231 C924 C476 R463 C475 L-CH FM 12 11 10 9 C229 R922 C926 C922 C927 Q923 C467 R-CH REAR SPEAKERS GND C614 I R927 R926 ZD921 3 2 1 GND D 131415161 R248 Q602 C468 L-CH R923 R924 R925 C610 1 2 3 R603 C601 R613 C608 C607 C603 R605 C602 R604 D601 Q601 R601 SO601 SPEAKER TERMINALS R256 C239 B C E Q2 E C R243 IC601 R602 R-CH FRONT SPEAKERS GND R246 C241 B C E C925 C923 C612 C609 C611 C606 C604 R609 R606 GND Q210 Q921 1 2 3 4 5 6 7 8 9 10 11 12 13 C E C B C240 R608 R607 R610 B 3 2 1 R259 C238 C236 R234 R921 Q922 C921 C903 D205 C265 R232 B C E R255 D901 Q211 D903 D904 D902 2 2 CNP901 1 R266 CNP902 SO901 AC SOCKET AC120V 60Hz C902 C901 A 5 6 CNS3 P25 5FROM MOTOR CD-C602,CP-C602 FROM TAPE MECHANISM P25 4-B FROM TAPE MECHANISM P25 1-H FROM TAPE MECHANISM P25 3-F FROM TAPE MECHANISM P25 2-H CNS203 CNS201 CNS204 CNS202 SW703 VOLUME DOWN R612 SW702 VOLUME UP R611 R220 1 2 3 R759 R758 1 2 3 SW705 FAST FORWARD R704 C704 R707 C705 C72 Q208 Q209 C707 R73 40 41 C43 C53 36 30 25 R746 R734 D704 R703 R705 R706 D701 L701 C714 C717 R712 SW714 MEMORY 20 R10 IC5 R29 SW712 BAND SW715 TUNING UP 19 5 R7 C712 Q91 C21 R25 35 10 15 SW716 TUNING DOWN 18 D2 CNP4 10 9 8 7 6 5 4 3 2 1 R761 D91 1 CNP3 1 2 3 4 5 6 C709 B C E C44 R19 C11 R8 R11 R12 R14 C15 R20 R17 C12 C14 R16 R15 C9 C10 C8 R9 R762 R96 R95 C17 R13 R28 C13 5 1 2 3 C18 20 16 17 R39 R40 15 R22 R24 10 R23 33 32 C16 R21 35 30 Q93 R94 C19 25 R765 R26 R31 45 IC1 C702 R764 R27 C20 R30 5 R744 R745 R740 R739 R741 R738 R97 R98 40 60 R93 9 8 7 6 5 4 3 2 1 R711 R34 R35 C32 R37 C31 C35 IC91 C45 60 61 SW706 REWIND R54 65 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 C91 49 48 64 1 R91 1 80 XL701 R718 R87 R86 R32 R33 C30 R41 55 R92 5 75 70 55 R731 L1 R88 16 17 50 R89 20 15 R36 C33 R90 33 C52 32 35 30 25 10 10 IC701 45 SW704 PLAY R725 R743 R719 R720 R729 R730 40 IC2 5 C59 R56 R38 34 C67 45 60 64 1 R57 15 R723 R717 R726 R727 R728 C42 R58 30 35 50 XL1 50 25 SW708 STOP 49 48 55 21 20 C68 R82 R60 C701 R701 C703 R702 R78 L2 R77 C69 R75 C71 C55 C716 R757 R760 R742 RX701 1 2 3 LCD701 R213 C209 C243 C242 C244 R252 R721 C713 Q703 R714 R208 ZD701 C51 C54 E C B C710 R253 R722 Q212 Q207 C70 R76 C56 C57 C22 R46 R47 R45 R724 C706 R212 R74 E C B SW709 DISC SKIP R251 R735 8 D705 D703 R257 Q702 E C B D81 R715 Q701 3 2 1 R250 E C B R205 E C B R736 R716 L203 R209 C207 R202 R203 R238 R204 R218 E C B R732 R749 R708 C708 D202 Q201 Q202 Q204 E C B Q214 R258 R211 C201 R215 R216 R214 C204 C203 Q203 C214 R226 R223 C218 B C E R235 R233 C222 R229 243 R260 B C E 7 6 5 4 3 2 1 CNP202 C220 C216 C229 C237 C223 C227 R236 R239 C210 C235 C212 C224 12 11 10 9 8 7 6 5 4 3 2 1 B C E CNP204 C215 R219 R217 C211 C219 IC201 SW707 OPEN/CLOSE C202 Q205 R210 B C E C208 R227 R225 R244 R228 C238 C236 R234 C228 R206 Q206 2 1 3 2 1 CNP201 R207 R737 D201 1 2 3 4 5 6 7 8 CNP203 R247 C217 C221 R224 C213 R245 C232 R240 R232 L205 Q213 13141516171819 20 21 22 23 24 R255 JK601 HEADPHONES C246 E C B R237 C230 R265 R259 D702 R254 R201 R230 SW710 X-BASS SW701 POWER C73 SW711 FUNCTION 1 CNS3A P25 5-H FROM CD MOTOR PWB 7 10 12 7 6 CNS4 P25 1-B FROM TRAY MOTOR PWB 8 DISPLAY PWB-A2 5 4 3 9 10 Figure 27 WIRING SIDE OF P.W.BOARD (3/3) – 27 – 11 12 CD-C602,CP-C602 VOLTAGE VOLTAGE 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 0V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 2.5V 0V 0V 0V 0V 0V 0V 0V 0V 0V 1.6V 2.5V 2.5V 2.5V 0V 2.5V 0V 0V 0V 2.5V 4V 4V 0V 0V 5V 5V 2.5V 2.5V 1V 1V 2.3V 5V 0V 5V PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 VOLTAGE 0V 0V 2.7V 0V 2.3V 5V 1V 0V 2.5V 2.5V 0V 0V 0V 5V 0V 0V 5V 5V 0V 0V – – 5V 0V 0V 0V 0V 0V – – – 0V 0V – – 5V 2.5V 0V 0V 2.5V 4.9V – 5V 1.9V 2.2V 0V – – – – – – 0V 0V 0V 4V 4V 0V – – 2.5V 0V 0V 0V IC201 IC5 IC2 IC1 PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 VOLTAGE 2.2V 2V – – 2.2V 2.2V 2.2V 0V 0V 0V 0V 2.2V 2.2V 2.2V 2.2V – 5V – – 5V 2.2V 2.2V 2.2V 2.2V 2.2V 0V 0V 0V 0V 2.2V 2.2V 2.2V – – – – PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 VOLTAGE 0V(0V) 0V(0V) 0.6V(0.6V) 2.7V(2.7V) 0V(0V) 0V(1.2V) 0V(0V) 0.6V(0.6V) 2.7V(2.7V) 2.7V(2.7V) 0V(0V) 0V(0V) 5.6V(5.6V) 3.4V(3.4V) 0V(0V) 2.7V(2.7V) 0.6V(0.6V) 0V(0V) 0V(0.8V) 0V(0V) 2.7V(2.7V) 0.6V(0.6V) 0V(0V) 0V(0V) IC301 PIN NO. 1 2 3 4 5 6 7 8 9 VOLTAGE 0.7V(0V) 1.5V(0V) 4.9V(0V) 1.5V(0V) 0V(0V) 4.9V(0V) 4V(0V) 4.7V(0V) 4.9V(0V) IC351 PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 VOLTAGE 1.7V(1.7V) 1.7V(1.7V) 5.5V(6.9V) 0.2V(0.8V) 1.7V(1.7V) 0V(0V) 5.5V(5.5V) 0V(0V) 2.4V(2.4V) 2.4V(2.4V) 4.8V(6.8V) 1V(1V) 1.1V(0V) 1.9V(1.7V) 1V(1.1V) 1.7V(1.7V) 1.7V(1.7V) 1.6V(1.6V) 0.4V(0.7V) 5.4V(6.8V) 5.4V(6.8V) 1.7V(1.7V) 1.7V(1.7V) 1.7V(1.7V) IC381 PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 VOLTAGE 2.7V(2.7V) 0V(0V) 0V(0V) 0V(4.7V) 0V(0V) 4.9V(4.9V) 0.2V(11.2V) 0V(0V) 0V(0V) 1V(0V) 5.5V(5.5V) 0V(0V) 0.3V(0.3V) 0V(0V) 0V(2.7V) 2.5V(0V) 5.2V(5.2V) 0V(1V) 0V(1V) 11.2V(10.6V) 0V(0V) 2.7V(2.7V) – 28 – IC431 PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 VOLTAGE 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 0V 5.6V 0V 5.6V 0V 0V 0V 0V 0V 0V 5.6V 0V 5.6V 0V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 5.6V 0V 5.6V 0V 5.6V 5.6V 11.3V 5.6V 0V 5.6V 0V 5.6V 5.6V 5.6V PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 IC701 VOLTAGE PIN NO. 2.2V 41 2.2V 42 2.2V 43 2.2V 44 2.2V 45 2.2V 46 2.2V 47 2.2V 48 2.2V 49 2.2V 50 2.2V 51 2.2V 52 2.2V 53 2.2V 54 2.2V 55 2.2V 56 2.2V 57 2.2V 58 2.2V 59 2.2V 60 61 2.2V 2.2V 62 63 2.2V 64 2.2V 4.3V 65 4.3V 66 3V 67 1.5V 68 4.3V 69 4.3V 70 4.3V 71 4.3V 72 0V 73 4.3V 74 4.3V 75 4.3V 76 4.3V 77 4.3V 78 4V 79 4V 80 IC601 PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 VOLTAGE 1.3V 0V 14V 0V 14V 0V 1.3V 14.7V 13V 7V 0V 7V 13V IC921 PIN NO. 1 2 3 VOLTAGE 17.6V 0V 5V VOLTAGE 0V 0V 4.3V 4.3V 0V 2.2V 0V 3.7V 3.7V 2.2V 0V 4.2V 0V 4.3V – – 4.3V 2.2V 1.8V 4.2V 4.2V 4.3V 4.3V 0V 0V 0V 0V 4.2V 2.2V 2.2V 2.2V 2.2V 2.2V 2.2V 2.2V 2.2V 2.2V 2.2V 2.2V 2.2V IC91 PIN NO. 1 2 3 4 5 6 7 8 9 VOLTAGE 2.2V 11.2V 0V – 0V 11.2V 0V 4.2V 2.2V CD-C602,CP-C602 TROUBLESHOOTING When the CD does not function When the CD section does not operate. When the objective lens of the optical pickup is dirty, this section may not operate. Clean the objective lens, and check the playback operation. When this section does not operate even after the above step is taken, check the following items. Remove the cabinet and follow the troubleshooting instructions. "Track skipping and/or no TOC (Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickup lens. Before attempting any adjustment make certain that the lens is clean. If not, clean it as mentioned below." Turn the power off. Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol. Do not touch the lens with the bare hand. Dust gradually accumulates on the objective lens during use, and it may degrade performance. To avoid this problem, use a cleaning disc designed for CD optical pickup lenses. HOW TO USE 1. Using the brush in the cleaner cap, apply 1 or 2 drops of the cleaning fluid to the brush on the CD cleaner disc which has the mark next to it. 2. Place the CD cleaner disc onto the CD disc tray with the brush side down, then press the play button. 3. You will hear music for about 20 seconds and the CD player will automatically stop. If it continues to turn, press the stop button. CAUTION The CD lens cleaner should be effective for 30~50 operations, however if the brushes become worn out earller then please replace the cleaner disc. If the CD cleaner brushes become very wet then wipe off any excess fluid with a soft cloth. Do not drink the cleaner fluid or allow it to come in contact with the eyes. In the event of this happening then drink and / or rinse with clean water and seek medical advice. The CD cleaner disc must not be used on car CD players or on computer CD ROM drives. All rights reserved. Unauthorized duplicating, broadcasting and renting this product is prohibited by law. Cleaner Liquid Cleaning Disc PARTS CODE: UDSKA0004AFZZ • When the turntable fails to stop. 5V Is from 2.5V 5 V till 2.5V down pulse (approx. 300 ms) 0V No Check the SW2 and the wiring from the IC2 pin 28 to the SW2. input into the IC2 pin 28 when the turntable is rotating? Yes Is there following voltage input on the IC2 pin 28 in the specific state? When the CD mechanism is moved up: 0V In other states: 4.3V No Yes Check IC2 pin26 Q91 and Q93 and the periphery. Yes IC2 defective. – 29 – Check the MECHA UP switch and the wiring from the IC2 pin 28 to the MECHA UP switch. CD-C602,CP-C602 • When turntable fails to move. Is there following voltage input on the IC2 pin 28 in the specific state? When the CD mechanism is moved up: 0V In other states: 4.3V No Check the MECHA UP switch and the wiring from the IC2 pin 28 to the MECHA UP switch. Yes Is L output from the IC2 pin 26 during SEC when the disc skip switch is pressed? Check the wiring of IC2 pin 26 and Q93 pin 2. No OK Yes IC2 defective. Is 4V output from the Q91 emitter during operation stated above? No Check Q91, Q93 and the periphery. Yes Check turntable motor and turntable mechanism. • When the CD tray fails to open or close. Is there following voltage input in specific state of IC2 pin 27? Open state: 0V Close state: 0V Intermediate state between open state and close state: 4.3V No Check the OPEN/CLOSE switch and the wiring from the IC2 pin 27 to the OPEN/CLOSE switch. Yes Is H output to IC2 pin 24 or 25 for 7 seconds when the OPEN/ CLOSE button is pressed? IC91 is defective. Replace it. Check the wiring of the IC2 pins 24 and 25, IC91 pins 1 and 3. No OK Yes IC2 defective. Is 4V output between IC91 pins 3 and 7 during operation stated above? Check the periphery of IC91. No OK Yes IC91 defective. Check the loading motor (M3) and the loading mechanism. • The CD function will not work. The CD operating buttons don't work. Yes Check the CD, DSP, power supply, and 16.93 MHz clock, and reset terminal. Yes Check the waveform of SCK, SO (DATA) and SI (COMM). Yes See if the pick-up in the PICKUP IN switch position. Yes If the items mentioned above are OK, check the main microcomputer IC701. – 30 – CD-C602,CP-C602 • The CD operating keys work. Check the Focus - HF system. Playback can be performed without a disc. Yes Does the pick-up move up and down twice? Focus search OK Yes No Does the output waveform of IC1(16)(FD) match that shown in Fig. 31-1? Check the area around IC5-CNP2. Yes No Check the IC1(50)(CLK) line, 4MHz. Check the microcomputer data on pins (51)(CL), (52)(DAT) and (53)CE. Focus search is performed two times when play operation is done without disc. 0.5s 0.50 V IC1 16 FD 0.5s 0.50 V IC1 7 TE 1 2 Figure 31-1 • Playback can only be performed when a disc is loaded. Is the Focus servo active? (Can you hear it working?) No Check the laser diode driver. Check the area around IC1(16) - (21) (focus servo circuit). No If the disc is not turning, the DRF Yes should not change to "H". Check the spin system. Level is abnormal. Check the periphery of IC1 pins 41 and 42. Yes Does the DRF signal change from "L" to "H"? Yes Is HF waveform normal (see the Fig. 31-2, Fig. 31-3)? Yes No Yes Waveform is unstable. Check the tracking system. HF 1.0V/DIV 0.5µsec/DIV(DC) (When playing back the disc) Yes Waveform in case of normal playback 0.5s 1.00 V IC1 16 FD 0.5s 10.0 V IC2 12 CLV+ 2 1 3 0.5s 10.0 V IC1 54 DRF 4 0.5s 2.00 V IC1 7 TE Figure 31-2 Figure 31-3 – 31 – Check the spin system. CD-C602,CP-C602 • Check the tracking system. Check waveform of IC1 pin 7 (TE). The waveform shown in Fig. 32-1 appears, and no-disc state appears soon. Play is possible in TEST mode. Data cannot be read. Yes Yes Yes Tracking servo is inoperative. Yes Although IL is possible, Yes play is impossible. Check the VCO-PLL system. Check the periphery of IC 1 pin 8 to pin 15, and IC 5 to CNP2. Normal jump is impeded, and the program top cannot be reached. Yes Check the periphery of IC 1 pin 14. 5ms 1.00 V IC1 7 TE 4 5 ms 5.0 V IC1 54 DRF 3 Figure 32-1 • Checking the spin system. Play operation is performed without disc. Yes The spin driver circuit is normal. The turntable rotates a little. Yes No The turntable fails to rotate or rotates at high speed. Yes Check the periphery of IC1 pins 23 to 27, pin 39, and pin 40, IC2 pin 12 and pin 13, IC5 to CNP3. • Checking the VCO-PLL system Play operation is performed when disc exits. Yes Although HF waveform is normal, TOC data cannot be read. Yes Check PDO waveform (Fig. 32-2). Abnormal Check the IC1 pins 43 and 44, IC2 pins 3, 5, 7, 10, and 11. Stop --> Play As VCO frequency is locked at 4.32 MHz, voltage of PDO rises and stabilizes. 0.5s 1.00 V IC2 3 PDO 2 0.5s 1.00 V IC1 16 FD 3 Figure 32-2 • Although HF waveform is normal and the time indication is normal, no sound is emitted. Check IC2 pin 48 (EFLG). Yes No Check IC2 pins 37, 40. Abnomal Check IC431 and POWER AMP. IC601. – 32 – Usually, the number of pulses of flawless disc is 100 pulses/sec or less. CD-C602,CP-C602 FUNCTION TABLE OF IC IC1 VHiLA9241M/-1: Servo Amp., (LA9241M) (1/2) Pin No. Port Name Function 1 FIN2 Connection pin for photodiode of pickup. RF signal is generated through addition with FIN pin, and FE signal is generated through subtraction. 2 FIN1 Connection pin for photodiode of pickup. 3 E Connection pin for photodiode of pickup. TE signal is generated through subtraction with F pin. 4 F Connection pin for photodiode of pickup. 5 TB Pin for input of DC component of TE signal. 6 TE- Pin to connect gain setting resistor of TE signal to TE signal. 7 TE TE signal output pin. 8 TESI TES (Track error sense) comparator input pin. TE signal is band-passed and input. 9 SCI Input pin for shock detection. 10 TH Pin to set time constant of tracking gain. 11* N.C. No connect. 12 TD- Pin to compose tracking phase compensation constant between TD and VR pins. 13 TD Pin to set tracking phase compensation. 14 JP Pin to set amplitude of tracking jump signal (kick pulse). 15 TO Tracking control signal output pin. 16 FD Focusing control signal output pin. 17 FD- Pin to compose focusing phase compensation constant between FD and FA pins. 18 FA Pin to compose focusing phase compensation constant between FD-/FA-pins. 19 FA- Pin to compose focusing phase compensation constant between FA and FE pins. 20 FE Output pin of FE signal. 21 FE- Pin to connect gain setting resistor of FE signal across TE pin. 22 AGND GND for analog signal. 23 SP Single end output for CV+ and CV- pin input. 24 SPI Spindle amplifier input. 25 SPG Pin to connect gain setting resistor in the 12cm mode of spindle. 26 SP- Pin to connect spindle phase compensation constant together with SPD pin. 27 SPO Spindle control signal output pin. 28 SLEO Pin to connect thread phase compensation constant. 29 SLD Thread control signal output pin. 30 SL- Input pin of thread feed signal from microcomputer. 31 SL+ Input pin of thread feed signal from microcomputer. 32 JP- Input pin of tracking jump signal from DSP. 33 JP+ Input pin of tracking jump signal from DSP. 34 TGL Input pin of tracking gain control signal from DSP. TGL = Gain low at "H" 35 TOFF Input pin of tracking off control signal from DSP. TOFF = Off at "H" 36 TES Output pin of TES signal to DSP. 37 HFL (HIGH FREQUENCY LEVEL) is used to judge whether main beam is positioned on the bit or on the mirror. 38 SLOF Thread servo off control input pin. 39 CV- Pin to input CLV error signal from DSP. 40 CV+ Pin to input CLV error signal from DSP. 41 RFSM RF output pin. 42 RFS- Pin to set gain of RF and set 3T compensation constant together with RFSM pin. 43 SLC (SLICE LEVEL CONTROL) is the output pin to control of the level of the data slice with RF waveform DSP. 44 SLI Input pin to control the level of data slice with DSP. 45 DGND GND pin in the digital system. 46 FSC Output pin for focus search smoothening capacitor. 47 TBC (Tracking Balance Control) Pin to set EF balance variable range. 48* NC No connect. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 33 – CD-C602,CP-C602 IC1 VHiLA9241M/-1: Servo Amp., (LA9241M) (2/2) Pin No. Port Name Function 49 DEF 50 CLK Defect detection output pin of disc. Reference clock input pin. 4.23MHz of DSP is input. 51 CL Microcomputer command clock input pin. 52 DAT Microcomputer command data input pin. 53 CE Microcomputer command chip enable input pin. 54 DRF (DETECT RF) RF level detection output. 55 FSS (Focus Serch Select) Pin to switch focus search mode. (± search/+ search for reference voltage) 56 VCC2 VCC pin for servo system and digital system. 57 REF1 Pin to connect pass control for reference voltage. 58 VR Reference voltage output pin. 59 LF2 Pin to set defect detection time constant of disc. 60 PHI Pin to connect capacitor for peak hold of RF signal. 61 BHI Pin to connect capacitor for bottom hold of RF signal. 62 LDO APC circuit output pin. 63 LDS APC circuit output pin. 64 VCC1 RF system VCC pin. 30 15K 15K 25K 29 27 28 26 (N.C)REGBASE VM4(+) 31 Vcc VM4(-) 32 VCTI3(+) VCTI4(-) 33 VCTI3(-) (N.C)GAIN4 34 VCTI3(OUT) (N.C)STAND BY 35 VM3(-) (N.C)SS.GND 36 GND VM3(+) (N.C)STAND BY IC5 VHiM56748FP-1: Focus/Tracking/Spin/Slide Driver (M56748FP) 25 24 23 22 21 20 19 10K 23K PA Stand by OP1 PA PA OP1 PA 10K 10K 10K Vcc TSD OP1 OP1 10K 10K PA PA PA 3.6K OP1 PA 10.8K OP1 10K VREI-OUT N.C GAIN1(N.C) VCTI(-) VM1(-) VM1(+) 8 9 10 GND 11 12 13 14 15 16 17 18 REG 5V(N.C) 7 Vcc 6 N.C 5 GAIN2 4 VCTI2(-) 3 VM2(-) 2 VM2(+) 1 VREI-IN 10K Figure 34 BLOCK DIAGRAM OF IC – 34 – CD-C602,CP-C602 IC2 VHiLC78622N-1: Servo/Signal Control (LC78622N) (1/2) Pin No. Terminal Name Input/Output 1 DEFI Input Input terminal of defect detection signal (DEF). (Connected to OV when not used.) 2 TAI Input For PLL 3 PDO Output For PLL Output terminal of phase comparison for external VCO control. 4 VVSS — For PLL Ground terminal for integrated VCO. Surely connected to 0V. 5 ISET Input For PLL Resistance connection terminal for current adjustment of PDO output. 6 VVDD 7 FR 8 VSS 9 EFMO Output For slice level control EFM signal output terminal. 10 EFMIN Input For slice level control EFM signal input terminal. 11 TEST2 Input Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V. 12 CLV+ Outout Output for disc motor control. 3 values can be output with the commands. 13 CLV- Output Output for disc motor control. 3 values can be output with the commands. 14 V/P Output Monitor output terminal for automatic switch of rough servo/phase control. "H" for rough servo, and "L" for phase servo. 15 HLF Intput Input terminal of track detection signal. Schmit input. 16 TES Input Input terminal of tracking error signal. Schmit input. 17 TOFF 18 19 Function Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V. — For PLL Power terminal for integrated VCO. Input For PLL VCO frequency range adjustment. — Ground terminal of digital system. Surely connected to 0V. Output Tracking OFF output terminal. TGL Output Output terminal for switch of tracking gain "L" increases the gain. JP+ Output Output for track jump control. 3 values can be output with the commands. 20 JP- Output Output for track jump control. 3 values can be output with the commands. 21* PCK (NC) Output Clock monitor terminal for EFM data replay. 4,3218MHz as the phase clock. 22* FSEQ (NC) Output Output terminal synchronous signal detection. "H" is output when synchronous signal detected by EFM signal matches synchronous signal internally generated. 23 VDD 24 CONT1 Input/Output General purpose input/output terminal 1 25 CONT2 Input/Output General purpose input/output terminal 2 26 CONT3 Input/Output General purpose input/output terminal 3 27 CONT4 Input/Output General purpose input/output terminal 4 28 CONT5 Input/Output General purpose input/output terminal 5 29* EMPH (NC) Output Difference monitor terminal At "H", deemphasis disk is being replayed. 30* C2F (NC) Output C2 flag output terminal. 31* DOUT (NC) Output Output terminal of digital OUTPUT. (EIAJ format) 32 TEST3 Input 33 TEST4 Input 34* N.C. 35* MUTEL (NC) Output L channel 1 bit DAC 36 LVDD — L channel 1 bit DAC Power terminal for L channel. 37 LCHO Output L channel 1 bit DAC L channel output terminal. 38 LVSS — L channel 1 bit DAC Ground terminal for L channel. Surely connected to 0V. 39 RVSS — R channel 1 bit DAC Ground terminal for R channel. Surely connected to 0V. 40 RCHO Output R channel 1 bit DAC R channel output terminal. — R channel 1 bit DAC Power terminal for R channel. Output R channel 1 bit DAC Mute output terminal for R channel. — — Power terminal of digital system. Controlled with serial data command from microcomputer. When not used, set it as the input terminal and open it by connecting to 0V, or set it as the output terminal and open it. Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V. Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V. Terminal not used. Open during operation. Mute output terminal for L channel. 41 RVDD 42* MUTER (NC) 43 XVDD — 44 XOUT Output 45 XIN 46 XVSS 47* SBSY (NC) Output Output terminal of synchronous signal of subcode block. 48* EFLG (NC) Output Correction monitor terminal of C1, C2, single and double. 49* PW (NC) Output Output terminal of subcodes P, A, R, S, T, U and W. Input — Power terminal for quartz oscillation. Ground terminal of 16.9344 MHz quartz oscillator. Ground terminal of 16.9344 MHz quartz oscillator. Ground terminal for quartz oscillation. Surely connected to 0V. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 35 – CD-C602,CP-C602 IC2 VHiLC78622N-1: Servo/Signal Control (LC78622N) (2/2) Pin No. Terminal Name Input/Output 50* SFSY (NC) Output Input Function Output terminal of synchronous signal of subcode frame. It drops when subcode stands by. 51 SBCK 52* FSX (NC) Output Output terminal of synchronous signal of 7.35kHz divided from quartz oscillation. 53 WRQ Output Output terminal to stand by output of subcode Q. 54 RWC 55 SQOUT 56 COIN Input Command input terminal from microcomputer. 57 /CQCK Input Clock input terminal to fetch command input, or pick up subcode from SQOUT. Schmit input. 58 /RES Input 59* TEST11 (NC) Output Output terminal for test. Used in the open state ("L" output as ordinary). 60* 16M (NC) Output Output terminal of 16.9344Hz. 61 4M Output Output terminal of 4.2336MHz. 62 TEST5 Input Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V. 63 /CS Input Chip selection input terminal. Pull-down resistor is integrated. Connected to 0when not controlled. 64 TEST1 Input Input terminal for test. Pull-down resistor is integrated. Surely connected to 0V. Input Output Clock input terminal to read subcode. Schmit input (Connected to 0V when not used.) Input terminal of read/write. Schmit input. Output terminal of subcode Q. Reset input terminal of LC78622. When turning on power, set it at "L". Note: The same potential must be supplied to the power terminals (VDD, VVDD, LVDD, RVDD, XVDD). In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0 RESET T1/T2 CE D1 CL D0 T1 PLAY T2 PLAY LCD S11 LCD S10 LCD S9 LCD S8 LCD S7 LCD S6 LCD S5 LCD S4 LCD S3 LCD S2 LCD S1 LCD S0 RESET P73 P72 P71 P70 P63 P62 P61 IC701 RH-iX0217AWZZ: System Microcomputer (IX0217AW) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 NC NC NC NC NC NC NC NC NC NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 IX0217AW 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 COM0 LCD COM0 COM1 LCD COM1 COM2 LCD COM2 COM3 LCD COM3 BIAS LCD BIAS VLC0 LCD VLC0 LCD VLC1 (NC)VLC1 LCD VLC1 (NC)VLC2 KI0 P40 KI1 P41 KI2 P42 KI3 P43 VSS GND KO0 P50 KO1 P51 KO2 P52 KO3 P53 REMOCON INT4 SYSTEM STOP P01 DRF P02 LCD S12 LCD S13 LCD S14 LCD S15 LCD S16 LCD S17 LCD S18 LCD S19 LCD S20 LCD S21 LCD S22 LCD S23 LCD BP0 LCD BP1 LCD BP2 LCD BP3 LCD BP4 LCD BP5 LCD BP6 LCD BP7 Figure 36 BLOCK DIAGRAM OF IC – 36 – 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 SPAN X2 X1 IC XT2(NC) XT1(NC) VDD(+5V) POWER(NC) POWER DSP RESET SLCOIN CQCK RWC SL+ SQOUT PUIN DISC NO REC WRQ P60 SYSTEM CLOCK SYSTEM CLOCK CONNECT VDD NC NC +5V P33 P32 P31 P30 P23 P22 P21 P20 P13 P12 P11 P10 P03 CD-C602,CP-C602 IC701 RH-iX0217AWZZ: System Microcomputer (IX0217AW) Pin No. Port Name Terminal Name SEG12-SEG20 Function Input/Output 1-9 S12-S20 Output 10*-12* S21-S23 N.C. — Not connect 13*-20* BP0-BP7 N.C. — Not connect 21-24 COM0-COM3 COM0-COM3 Output LCD Common 25 BIAS BIAS Output LCD Bias 26 VLC0 VLC0 — LCD Bias 27* VLC1 (N.C.) VLC1 — Not connect 28* VLC2 (N.C.) VLC2 — Not connect 29 P40 KI0 Input Key In 0 30 P41 KI1 Input Key In 1 31 P42 KI2 Input Key In 2 32 P43 KI3 Input 33 VSS VSS — 34 P50 KO0 Output Key Out 0 35 P51 KO1 Output Key Out 1 36 P52 KO2 Output Key Out 2 37 P53 KO3 Output Key Out 3 38 P00 REMOCON Input Remocon Input 39 P01 SYSTEM STOP Input System stop detect 40 P02 DRF Input Focus ok flug 41 P03 WRQ Input Write request from contrroer 42 P10 REC Input REC ON 43 P11 DISC NO. Input Disc No. detector 44 P12 PU IN Input Pickup In side switch 45 P13 SQOUT Input SQ data from DSP 46 P20 SL+ 47 P21 RWC Output Read/Write control 48 P22 CQCK Output Clock for CD DSP 49 P23 COIN Output Command data for DSP 50 P30 SL– Output Slide – 51 P31 DSP RST Output CD DSP Reset 52 P32 POWER Output Power ON/OFF control 53* P33 POWER (N.C.) Output — LCD Segment Key In 3 VSS Slide + Not connect 54 VDD VDD (+5V) — VDD +5V 55* XT1 XT1 (N.C.) — Not connect 56* XT2 XT2 (N.C.) — Not connect 57 IC IC — Connect to VDD 58 X1 X1 — X-TAL OSC IN 59 X2 X2 — X-TAL OSC OUT 60 P60 SPAN Input Span selector 9K/10K 61 P61 T2 PLAY Input Tape 2 Play detect 62 P62 T1 PLAY Input Tape 1 Play detect 63 P63 D0 Input Data in to VOL/PLL 64 P70 CL Output Clock for VOL/PLL 65 P71 DI Output Data in to VOL/PLL 66 P72 CE Output Chip enable for VOL/PLL 67 P73 T1/T2 Output 68 RESET RESET 69-80 S0-S11 SEG0-SEG11 Tape play SW H: Tape 1 L: Tape 2 Input System reset Output LCD Segment In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 37 – CD-C602,CP-C602 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 COM0 COMMON COM3 3 COM1 2 COM2 SEG19 SEG20 SEG18 SEG8 SEG17 SEG7 SEG16 SEG6 SEG15 SEG5 SEG14 SEG4 SEG13 SEG3 SEG12 SEG2 SEG11 SEG1 1 SEG9 SEG0 SEGMENT SEG10 LCD701: RV-LX0024AWZZ LCD Display 22 23 24 25 PIN COM1 COM2 COM3 COM4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 TONE LOW X9 4I X6 NC X4 1A X5 2A 3H,3I 3A NC 4A 5B,5C 6A NC 7A ST 8A X-BASS 9A COM1 NC NC NC MEMORY COL 4H X7 X1 1F 1B 2F 2B 3F 3B 4F 4B 6F 6B 7F 7B 8F 8B 9F 9B NC COM2 NC NC kHz DP 4K CH X2 1E 1G 2E 2G 3E 3G 4E 4G 6E 6G 7E 7G 8E 8G 9E 9G NC NC COM3 NC MHz NC 4J X8 X3 1D 1C 2D 2C 3D 3C 4D 4C 6D 6C 7D 7C 8D 8C 9D 9C NC NC NC COM4 Figure 38 LCD SEGMENT – 38 – CD-C602,CP-C602 PARTS GUIDE MODEL CD-C602 CP-C602 CD-C602 mini component system consisting of CD-C602 mini component system, CP-C602 and rear (GBOXS0020AWM1) speaker system. “HOW TO ORDER REPLACEMENT PARTS” To have your order filled promptly and correctly, please furnish the following information. 1. MODEL NUMBER 2. REF. No. 3. PART NO. 4. DESCRIPTION For U.S.A. only Contact your nearest SHARP Parts Distributor to order. For location of SHARP Parts Distributor, Please call Toll-Free; 1-800-BE-SHARP MARK: SPARE PARTS-DELIVERY SECTION Explanation of capacitors/resistors parts codes Capacitors Resistors VCC ....................... Ceramic type VCK ........................ Ceramic type VCT ........................ Semiconductor type VC • • MF ............... Cylindrical type (without lead wire) VC • • MN ............... Cylindrical type (without lead wire) VC • • TV ................ Square type (without lead wire) VC • • TQ ............... Square type (without lead wire) VC • • CY ............... Square type (without lead wire) VC • • CZ ............... Square type (without lead wire) VC • • • • • • • • • J .. The 13th character represents capacity difference. ("J" ±5%, "K" ±10%, "M" ±20%, "N" ±30%, "C" ±0.25 pF, "D" ±0.5 pF, "Z" +80-20%.) VRD ....................... Carbon-film type VRS ........................ Carbon-film type VRN ....................... Metal-film type VR • • MF ............... Cylindrical type (without lead wire) VR • • MN ............... Cylindrical type (without lead wire) VR • • TV ................ Square type (without lead wire) VR • • TQ ............... Square type (without lead wire) VR • • CY ............... Square type (without lead wire) VR • • CZ ............... Square type (without lead wire) VR • • • • • • • • • J .. The 13th character represents error. ("J" ±5%, "F" ±1%, "D" ±0.5%.) If there are no indications for the electrolytic capacitors, error is ±20%. If there are no indications for other parts, the resistors are ±5% carbon-film type. NOTE: Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace parts with specified ones for maintaining the safety and performance of the set. – 39 – CD-C602,CPC602 NO. PRICE RANK PARTS CODE DESCRIPTION CD-C602 INTEGRATED CIRCUITS IC1 IC2 IC5 VHILA9241M/-1 VHILC78622N-1 VHIM56748FP-1 J J J IC91 IC201 VHITA7291S/-1 VHIAN7345K/-1 J J IC301 IC351 VHITA7358AP-1 VHILA1805//-1 J J IC381 IC431 IC601 IC701 VHILC72131/-1 VHILC75394E-1 VHILA4597//-1 RH-IX0217AWZZ J J J J IC921 VHIKIA7805P-1 J AS Servo Amp.,LA9241M AY Servo/Signal Control,LC78622N AR Focus/Tracking/Spin/Slide Driver,M56748FP AH Loading Motor Driver,TA7291S AM Playback and Record/Playback Amp.,AN7345K AG FM Front End,TA7358AP AM FM IF DET./FM MPX./AM IF, LA1805 AP PLL Controller,LC72131 AX Audio Processor,LC75394E AH Power Amp.,LA4597 AX System Microcomputer, IX0217AW AF Voltage Regulator,KIA7805P VSKTA1266GR-1 VSKTA1271Y/-1 VSKRC102M//-1 VS2SC2389SE-1 VSKTC3199GR-1 VSKTA1266GR-1 VSKRC104M//-1 VSKTC3199GR-1 VSKTC3203Y/-1 VSKTC3199GR-1 VSKTC3194Y/-1 VSKRA109M//-1 VSKRA102M//-1 VSKRA102M//-1 VSKRC102M//-1 VSKRC102M//-1 VSKTC3199GR-1 VSKTA1271Y/-1 VSKRC102M//-1 VS2SD2012Y/-1 J J J J J J J J J J J J J J J J J J J J AB AC AC AD AB AB AC AB AC AB AD AC AC AC AC AC AB AC AC AF Silicon,PNP,KTA1266 GR Silicon,PNP,KTA1271 Y Digital,NPN,KRC102 M Silicon,NPN,2SC2389 SE Silicon,NPN,KTC3199 GR Silicon,PNP,KTA1266 GR Digital,NPN,KRC104 M Silicon,NPN,KTC3199 GR Silicon,NPN,KTC3203 Y Silicon,NPN,KTC3199 GR Silicon,NPN,KTC3194 Y Digital,PNP,KRA109 M Digital,PNP,KRA102 M Digital,PNP,KRA102 M Digital,NPN,KRC102 M Digital,NPN,KRC102 M Silicon,NPN,KTC3199 GR Silicon,PNP,KTA1271 Y Digital,NPN,KRC102 M Silicon,NPN,2SD2012 Y VHD1SS133//-1 VHD1SS133//-1 VHD1SS133//-1 VHD1N4004S/-1 VHD1SS133//-1 VHD1SS133//-1 VHD1SS133//-1 VHD1SS133//-1 VHD1SS133//-1 VHD1SS133//-1 VHDRL203F//-1 VHCSVC211C/-1 VHCSVC348S/-1 VHEMTZJ5R1B-1 VHEMTZJ3R3B-1 VHEMTZJ130A-1 J J J J J J J J J J J J J J J J AA AA AA AB AA AA AA AA AA AA AE AG AK AC AA AC Silicon,1SS133 Silicon,1SS133 Silicon,1SS133 Silicon,1N4004S Silicon,1SS133 Silicon,1SS133 Silicon,1SS133 Silicon,1SS133 Silicon,1SS133 Silicon,1SS133 Silicon,RL203F Variable Capacitance,SVC211C Variable Capacitance,SVC348S Zener,5.1V,MTZJ5.1B Zener,3.3V,MTZJ3.3B Zener,13V,MTZJ13A RFILF0124AFZZ 92LFILTA1768A J J AD FM IF,10.7 MHz AE AM IF RTRNP0238AWZZ RCILI0012AWZZ RCILA0052AWZZ RCILB0058AWZZ RCILI0015AWZZ RCILI0016AWZZ J J J J J J AY AD AE AC AE AC VP-XHR82K0000 VP-CH270K0000 J J AC 0.82 µH,Choke AB 2.7 µH,Choke TRANSISTORS Q1 Q91 Q93 Q201~204 Q205,206 Q207 Q208,209 Q210,211 Q212 Q213,214 Q302 Q352 Q381 Q601 Q602 Q701 Q702,703 Q921 Q922 Q923 DIODES D2 D81 D91 D201,202 D205 D303 D331 D381 D601 D701~705 D901~904 VD301,302 VD331 ZD381 ZD701 ZD921 FILTERS CF302 CF351 TRANSFORMERS ! PT901 T301 T331 T333 T351 T352 Power FM IF AM Antenna AM Oscillation AM IF FM Detection COILS L1 L2 NO. L203 L205 L301 L302 L303 L381 L701 PRICE RANK PARTS CODE VP-CH331K0000 VP-CH101K0000 RCILF0001AWZZ RCILR0029AWZZ RCILB0060AWZZ VP-DH101K0000 VP-CH101K0000 DESCRIPTION 330 µH,Choke 100 µH,Choke FM Band Pass Filter FM RF FM Oscillation 100 µH,Choke 100 µH,Choke J J J J J J J AB AB AC AA AC AB AB J AC 6.8 kohms (B),Semi-VR [VCO] VARIABLE RESISTOR VR351 RVR-M0025AWZZ VIBRATORS X381 XL1 XL701 RCRSP0002AWZZ J 92LCRSTL1746AT J 92LCRSTL-1595A J AH Crystal,4.5 MHz AH Crystal,16.9344 MHz AE Crystal,4.19 MHz CAPACITORS C1 C2 C3 C4 C5,6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 C20 C21 C22 C24 C25 C30 C31 C32 C33 C34 C35 C37 C38 C39 C40 C41,42 C43 C44 C45 C50 C51 C52 C53 C54~57 C58 C59 C67,68 C69,70 C71 C72,73 C74 C75 C91 C201,202 C203,204 C207,208 C209 C210~213 C214,215 C216,217 C218,219 C220,221 C222 C223 –1– VCTYMN1CY103N VCEAZA1EW476M VCEAEA1HW104M VCKYMN1HB102K VCQYKA1HM333K VCEAEA1HW104M VCQYKA1HM683K VCQYKA1HM473K VCKYMN1HB181K VCQYKA1HM104K VCKYMN1HB331K VCQYKA1HM104K VCTYMN1CY103K VCTYMN1CX472K VCKYMN1HB102K VCEAEA1HW474M VCEAEA1HW105M VCEAZA1EW476M VCTYMN1CX332K VCEAEA1HW105M VCTYMN1CY103N VCEAEA1HW105M VCTYMN1CY103N VCCSMN1HL2R2C VCTYMN1CX272K VCCSMN1HL270J VCKYMN1HB102K VCQYKA1HM333K VCEAEA1HW104M VCEAZA0JW227M VCTYMN1CY103K VCEAEA1HW474M VCEAEA1HW334M VCQYKA1HM473K VCEAZA1AW107M VCEAZA1AW337M VCEAEA1HW475M VCQYKA1HM104K VCTYMN1EF223Z VCEAZA1AW107M VCKYMN1HB221K VCKYMN1HB101K VCKYPA1HB221K VCQYKA1HM223K VCEAZA1HW106M VCKYMN1HB221K VCKYMN1HB331K VCKYMN1HB101K VCKYBT1HB101K VCKYMN1HB101K VCEAZA1EW476M VCKYMN1HB102K VCKYMN1HB181K VCKYMN1HB102K VCQYKA1HM223K VCKYMN1HB331K VCEAZA1EW476M VCQYKA1HM333K VCKYMN1HB561K VCEAEA1HW105M VCEAEA1CW226M VCTYMN1EF223Z J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AB AB AA AB AB AB AB AA AB AA AB AA AA AA AB AB AB AA AB AA AB AA AB AA AA AA AB AB AC AA AB AB AB AB AC AB AB AA AB AA AA AA AB AB AA AA AA AA AA AB AA AA AA AB AA AB AB AA AB AB AA 0.01 µF,16V 47 µF,25V,Electrolytic 0.1 µF,50V,Electrolytic 0.001 µF,50V 0.033 µF,50V,Mylar 0.1 µF,50V,Electrolytic 0.068 µF,50V,Mylar 0.047 µF,50V,Mylar 180 pF,50V 0.1 µF,50V,Mylar 330 pF,50V 0.1 µF,50V,Mylar 0.01 µF,16V 0.0047 µF,16V 0.001 µF,50V 0.47 µF,50V,Electrolytic 1 µF,50V,Electrolytic 47 µF,25V,Electrolytic 0.0033 µF,16V 1 µF,50V,Electrolytic 0.01 µF,16V 1 µF,50V,Electrolytic 0.01 µF,16V 2.2 pF,50V 0.0027 µF,16V 27 pF,50V 0.001 µF,50V 0.033 µF,50V,Mylar 0.1 µF,50V,Electrolytic 220 µF,6.3V,Electrolytic 0.01 µF,16V 0.47 µF,50V,Electrolytic 0.33 µF,50V,Electrolytic 0.047 µF,50V,Mylar 100 µF,10V,Electrolytic 330 µF,10V,Electrolytic 4.7 µF,50V,Electrolytic 0.1 µF,50V,Mylar 0.022 µF,25V 100 µF,10V,Electrolytic 220 pF,50V 100 pF,50V 220 pF,50V 0.022 µF,50V,Mylar 10 µF,50V,Electrolytic 220 pF,50V 330 pF,50V 100 pF,50V 100 pF,50V 100 pF,50V 47 µF,25V,Electrolytic 0.001 µF,50V 180 pF,50V 0.001 µF,50V 0.022 µF,50V,Mylar 330 pF,50V 47 µF,25V,Electrolytic 0.033 µF,50V,Mylar 560 pF,50V 1 µF,50V,Electrolytic 22 µF,16V,Electrolytic 0.022 µF,25V CD-C602,CPC602 NO. C224 C227,228 C229,230 C231,232 C235,236 C237,238 C239 C240 C241 C242 C243 C244 C246 C265 C301 C302 C312 C313 C314 C315 C316 C317 C318 C319 C320 C321 C322 C323 C324 C325 C326 C327 C328 C331 C332 C333 C336 C339 C342 C344 C351,352 C353 C354 C355 C356 C357 C358 C359,360 C362 C363 C364 C371,372 C373,374 C383 C384 C385 C387 C388 C390 C391 C392 C393 C431~436 C439,440 C441,442 C443,444 C445,446 C459,460 C461,462 C463,464 C465~468 C471 C475 C476 C481,482 C601,602 C603,604 C606 C607,608 C609,610 C611,612 C613,614 PARTS CODE VCEAEA1HW335M VCKYMN1HB102K VCEAEA1CW226M VCQYKA1HM473K VCTYMN1CX332K VCEAEA1HW105M VCQYKA1HM823K VCEAEA1CW226M VCEAZA1AW107M VCQYKA1HM392K VCQYKA1HM273K VCEAZA1EW476M VCEAZA1EW476M VCEAEA1HW475M VCKYMN1HB820K VCCSMN1HL6R8K VCCSMN1HL100J VCTYMN1CX472K VCCUMN1HJ4R7D VCTYMN1CY103N VCTYMN1CX472K VCCSMN1HL4R7C VCKYMN1HB102K VCTYMN1EF223Z VCKYMN1HB102K VCTYMN1EF223Z VCCCMN1HH150J VCCSMN1HL180J VCCUMN1HJ3R3K VCCCMN1HH220J VCTYMN1EF223Z VCKYMN1HB101K VCEAZA1HW106M VCKZPA1HF223Z VCKYMN1HB102K VCCSPA1HL561J VCCUMN1HJ220J VCKZPA1HF473Z VCTYMN1EF223Z VCCUMN1HJ180J VCTYMN1EF223Z VCEAZA1HW106M VCEAZA1AW227M VCTYMN1EF223Z VCTYMN1CX222K VCTYMN0JY183M VCKYMN1HB471K VCEAEA1HW335M VCEAEA1HW335M VCEAEA1HW105M CPU100V1500PJ VCQYKA1HM183K VCEAEA1HW105M VCTYMN1EF223Z VCEAZA1EW476M VCEAEA1HW105M VCKYMN1HB101K VCKYMN1HB102K VCCCMN1HH120J VCCCMN1HH150J VCKYMN1HB102K VCEAEA1CW226M VCQYKA1HM473K VCEAEA1CW226M VCKYMN1HB181K VCEAZA1HW684M VCQYKA1HM223K VCTYMN1CX272K VCEAZA1AW107M VCKYMN1HB101K VCEAZA1HW106M VCKZPA1HF223Z VCEAZA1AW107M VCEAZA1CW107M VCEAEA1HW225M VCKYPA1HB102K VCEAZA1AW107M VCEAZA1EW227M VCEAZA1AW107M VCEAZA1CW477M VCQYKA1HM104K VCEAZA1HW226M J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J PRICE RANK DESCRIPTION AB AA AB AB AA AB AC AB AB AA AB AB AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AB AA AA AA AA AA AA AA AA AB AC AA AA AA AA AB AB AB AC AB AB AA AB AB AA AA AA AA AA AB AB AB AA AB AB AA AB AA AB AA AB AC AB AA AB AC AB AC AB AB 3.3 µF,50V,Electrolytic 0.001 µF,50V 22 µF,16V,Electrolytic 0.047 µF,50V,Mylar 0.0033 µF,16V 1 µF,50V,Electrolytic 0.082 µF,50V,Mylar 22 µF,16V,Electrolytic 100 µF,10V,Electrolytic 0.0039 µF,50V,Mylar 0.027 µF,50V,Mylar 47 µF,25V,Electrolytic 47 µF,25V,Electrolytic 4.7 µF,50V,Electrolytic 82 pF,50V 6.8 pF,50V 10 pF,50V 0.0047 µF,16V 4.7 pF (UJ),50V 0.01 µF,16V 0.0047 µF,16V 4.7 pF,50V 0.001 µF,50V 0.022 µF,25V 0.001 µF,50V 0.022 µF,25V 15 pF (CH),50V 18 pF,50V 3.3 pF (UJ),50V 22 pF (CH),50V 0.022 µF,25V 100 pF,50V 10 µF,50V,Electrolytic 0.022 µF,50V 0.001 µF,50V 560 pF,50V 22 pF (UJ),50V 0.047 µF,50V 0.022 µF,25V 18 pF (UJ),50V 0.022 µF,25V 10 µF,50V,Electrolytic 220 µF,10V,Electrolytic 0.022 µF,25V 0.0022 µF,16V 0.018 µF,6.3V 470 pF,50V 3.3 µF,50V,Electrolytic 3.3 µF,50V,Electrolytic 1 µF,50V,Electrolytic 0.0015 µF,100V,Polypropylene 0.018 µF,50V,Mylar 1 µF,50V,Electrolytic 0.022 µF,25V 47 µF,25V,Electrolytic 1 µF,50V,Electrolytic 100 pF,50V 0.001 µF,50V 12 pF (CH),50V 15 pF (CH),50V 0.001 µF,50V 22 µF,16V,Electrolytic 0.047 µF,50V,Mylar 22 µF,16V,Electrolytic 180 pF,50V 0.68 µF,50V,Electrolytic 0.022 µF,50V,Mylar 0.0027 µF,16V 100 µF,10V,Electrolytic 100 pF,50V 10 µF,50V,Electrolytic 0.022 µF,50V 100 µF,10V,Electrolytic 100 µF,16V,Electrolytic 2.2 µF,50V,Electrolytic 0.001 µF,50V 100 µF,10V,Electrolytic 220 µF,25V,Electrolytic 100 µF,10V,Electrolytic 470 µF,16V,Electrolytic 0.1 µF,50V,Mylar 22 µF,50V,Electrolytic NO. –2– C701 C702 C703~705 C706 C707~710 C712 C713 C714 C716 C717 C901,902 C903 C921,922 C923 C924 C925 C926 C927 PRICE RANK PARTS CODE VCKYMN1HB101K VCTYMN1CY103N VCKYMN1HB101K VCEAEA1HW335M VCTYMN1CY103N VCEAZA1EW476M VCEAZA1HW106M VCTYMN1EF223Z VCEAZA1AW107M VCTYMN1EF223Z VCQYKA1HM473K VCEAZW1EW338M VCQYKA1HM223K VCEAZA1CW227M VCEAZA1EW477M VCEAZA1EW476M VCKZPA1HF223Z VCQYKA1HM104K DESCRIPTION J J J J J J J J J J J J J J J J J J AA AA AA AB AA AB AB AA AB AA AB AG AB AC AD AB AA AB 100 pF,50V 0.01 µF,16V 100 pF,50V 3.3 µF,50V,Electrolytic 0.01 µF,16V 47 µF,25V,Electrolytic 10 µF,50V,Electrolytic 0.022 µF,25V 100 µF,10V,Electrolytic 0.022 µF,25V 0.047 µF,50V,Mylar 3300 µF,25V 0.022 µF,50V,Mylar 220 µF,16V,Electrolytic 470 µF,25V,Electrolytic 47 µF,25V,Electrolytic 0.022 µF,50V 0.1 µF,50V,Mylar J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 0 ohm,Jumper,ø1.4×3.5mm,Ivory 1 kohm,1/8W 100 kohm,1/8W 15 kohms,1/8W 2.2 kohms,1/8W 6.8 kohms,1/8W 100 ohm,1/8W 1 kohm,1/8W 12 kohms,1/8W 27 kohms,1/8W 82 kohms,1/6W 3.3 kohms,1/8W 15 kohms,1/8W 33 kohms,1/8W 10 kohm,1/8W 47 kohms,1/8W 1.5 kohms,1/8W 82 kohms,1/8W 3.3 Mohms,1/6W 39 kohms,1/8W 10 kohm,1/8W 56 kohms,1/8W 6.8 kohms,1/8W 1.2 kohms,1/8W 10 kohm,1/8W 1.2 kohms,1/8W 220 kohms,1/6W 1 kohm,1/6W 18 kohms,1/8W 10 kohm,1/8W 56 kohms,1/8W 5.6 kohms,1/8W 1 kohm,1/8W 470 ohms,1/8W 47 kohms,1/8W 33 kohms,1/8W 22 kohms,1/8W 4.7 kohms,1/8W 560 ohms,1/8W 12 ohms,1/8W 1 kohm,1/6W 1 kohm,1/8W 1 kohm,1/6W 1.2 kohms,1/8W 27 kohms,1/8W 680 ohms,1/8W 1 kohm,1/8W 4.7 kohms,1/8W 4.7 kohms,1/6W 1 kohm,1/8W 1 kohm,1/6W 100 ohm,1/8W 1 kohm,1/8W 1 kohm,1/6W 10 kohm,1/6W 4.7 ohms,1/4W 56 ohms,1/4W 2.2 kohms,1/8W 10 kohm,1/8W 2.2 kohms,1/8W 10 kohm,1/6W RESISTORS R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 R14 R15 R16 R17 R18 R19 R20 R21 R22 R23 R24 R25 R26,27 R28,29 R30 R31 R32 R33 R34 R35 R36,37 R38 R39,40 R41 R42 R43 R45 R46,47 R54 R56 R57 R58 R60 R73 R74 R75,76 R77,78 R82 R86~88 R89,90 R91,92 R93 R94 R95 R96 R97 R98 VRD-MN2BD000C VRD-MN2BD102J VRD-MN2BD104J VRD-MN2BD153J VRD-MN2BD222J VRD-MN2BD682J VRD-MN2BD101J VRD-MN2BD102J VRD-MN2BD123J VRD-MN2BD273J VRD-ST2CD823J VRD-MN2BD332J VRD-MN2BD153J VRD-MN2BD333J VRD-MN2BD103J VRD-MN2BD473J VRD-MN2BD152J VRD-MN2BD823J VRD-ST2CD335J VRD-MN2BD393J VRD-MN2BD103J VRD-MN2BD563J VRD-MN2BD682J VRD-MN2BD122J VRD-MN2BD103J VRD-MN2BD122J VRD-ST2CD224J VRD-ST2CD102J VRD-MN2BD183J VRD-MN2BD103J VRD-MN2BD563J VRD-MN2BD562J VRD-MN2BD102J VRD-MN2BD471J VRD-MN2BD473J VRD-MN2BD333J VRD-MN2BD223J VRD-MN2BD472J VRD-MN2BD561J VRD-MN2BD120J VRD-ST2CD102J VRD-MN2BD102J VRD-ST2CD102J VRD-MN2BD122J VRD-MN2BD273J VRD-MN2BD681J VRD-MN2BD102J VRD-MN2BD472J VRD-ST2CD472J VRD-MN2BD102J VRD-ST2CD102J VRD-MN2BD101J VRD-MN2BD102J VRD-ST2CD102J VRD-ST2CD103J VRD-ST2EE4R7J VRD-ST2EE560J VRD-MN2BD222J VRD-MN2BD103J VRD-MN2BD222J VRD-ST2CD103J CD-C602,CPC602 NO. R201 R202 R203,204 R205 R206,207 R208~213 R214 R215 R216,217 R218,219 R220 R223,224 R225,226 R227 R228 R229 R230 R231,232 R233 R234 R235 R236,237 R238 R239,240 R243~249 R250 R251 R252 R253 R254 R255 R256 R257 R258 R259 R260 R265 R266 R311 R312 R313 R314 R315 R316 R317 R318 R319 R320 R331 R339 R351 R352 R353 R354 R357 R358 R359 R360 R363 R373,374 R375,376 R386 R387 R388 R390 R391 R392 R393~396 R397 R399 R447,448 R449,450 R451,452 R460~462 R463 R601,602 R603,604 R605,606 R607,608 R609,610 R611,612 R613 PRICE RANK PARTS CODE VRD-ST2CD103J VRD-MN2BD332J VRD-MN2BD682J VRD-MN2BD332J VRD-ST2CD102J VRD-MN2BD103J VRD-MN2BD102J VRD-ST2CD102J VRD-ST2CD560J VRD-MN2BD104J VRD-MN2BD103J VRD-MN2BD392J VRD-MN2BD562J VRD-MN2BD333J VRD-MN2BD683J VRD-MN2BD333J VRD-ST2CD223J VRD-MN2BD332J VRD-ST2CD682J VRD-MN2BD682J VRD-MN2BD222J VRD-MN2BD561J VRD-MN2BD103J VRD-MN2BD101J VRD-MN2BD103J VRD-MN2BD473J VRD-ST2CD682J VRD-MN2BD104J VRD-MN2BD120J VRD-ST2CD103J VRD-MN2BD102J VRD-ST2CD471J VRD-ST2EE151J VRD-ST2CD104J VRD-MN2BD104J VRD-ST2CD682J VRD-MN2BD103J VRD-MN2BD104J VRD-MN2BD104J VRD-ST2CD220J VRD-MN2BD333J VRD-MN2BD100J VRD-MN2BD473J VRD-ST2CD470J VRD-ST2CD103J VRD-MN2BD681J VRD-ST2CD472J VRD-ST2CD821J VRD-MN2BD683J VRD-MN2BD103J VRD-MN2BD392J VRD-MN2BD333J VRD-MN2BD152J VRD-MN2BD473J VRD-ST2CD122J VRD-MN2BD153J VRD-MN2BD103J VRD-ST2EE471J VRD-ST2CD103J VRD-ST2CD272J VRD-ST2CD332J VRD-ST2CD103J VRD-ST2EE151J VRD-MN2BD152J VRD-ST2CD222J VRD-ST2CD473J VRD-ST2CD102J VRD-MN2BD102J VRD-MN2BD472J VRD-MN2BD103J VRD-MN2BD332J VRD-MN2BD103J VRD-ST2CD102J VRD-ST2CD102J VRD-ST2EE221J VRD-ST2CD103J VRD-ST2CD332J VRD-ST2CD121J VRD-ST2CD3R3J VRD-ST2CD122J VRD-ST2EE221J VRD-ST2CD102J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA DESCRIPTION 10 kohm,1/6W 3.3 kohms,1/8W 6.8 kohms,1/8W 3.3 kohms,1/8W 1 kohm,1/6W 10 kohm,1/8W 1 kohm,1/8W 1 kohm,1/6W 56 ohms,1/6W 100 kohm,1/8W 10 kohm,1/8W 3.9 kohms,1/8W 5.6 kohms,1/8W 33 kohms,1/8W 68 kohms,1/8W 33 kohms,1/8W 22 kohms,1/6W 3.3 kohms,1/8W 6.8 kohms,1/6W 6.8 kohms,1/8W 2.2 kohms,1/8W 560 ohms,1/8W 10 kohm,1/8W 100 ohm,1/8W 10 kohm,1/8W 47 kohms,1/8W 6.8 kohms,1/6W 100 kohm,1/8W 12 ohms,1/8W 10 kohm,1/6W 1 kohm,1/8W 470 ohms,1/6W 150 ohms,1/4W 100 kohm,1/6W 100 kohm,1/8W 6.8 kohms,1/6W 10 kohm,1/8W 100 kohm,1/8W 100 kohm,1/8W 22 ohms,1/6W 33 kohms,1/8W 10 ohm,1/8W 47 kohms,1/8W 47 ohms,1/6W 10 kohm,1/6W 680 ohms,1/8W 4.7 kohms,1/6W 820 ohms,1/6W 68 kohms,1/8W 10 kohm,1/8W 3.9 kohms,1/8W 33 kohms,1/8W 1.5 kohms,1/8W 47 kohms,1/8W 1.2 kohms,1/6W 15 kohms,1/8W 10 kohm,1/8W 470 ohms,1/4W 10 kohm,1/6W 2.7 kohms,1/6W 3.3 kohms,1/6W 10 kohm,1/6W 150 ohms,1/4W 1.5 kohms,1/8W 2.2 kohms,1/6W 47 kohms,1/6W 1 kohm,1/6W 1 kohm,1/8W 4.7 kohms,1/8W 10 kohm,1/8W 3.3 kohms,1/8W 10 kohm,1/8W 1 kohm,1/6W 1 kohm,1/6W 220 ohms,1/4W 10 kohm,1/6W 3.3 kohms,1/6W 120 ohms,1/6W 3.3 ohms,1/6W 1.2 kohms,1/6W 220 ohms,1/4W 1 kohm,1/6W NO. R701,702 R703 R704 R705 R706 R707,708 R711,712 R714~716 R717 R718 R719,720 R721 R722 R723 R724 R725~729 R730,731 R732 R734,735 R736 R737 R738~741 R742 R743 R744,745 R749 R757~760 R761 R762 R764 R765 R921 R922 R923 R924 R925 R926 R927 PRICE RANK PARTS CODE VRD-MN2BD104J VRD-MN2BD102J VRD-MN2BD104J VRD-MN2BD102J VRD-MN2BD332J VRD-MN2BD104J VRD-MN2BD103J VRD-MN2BD103J VRD-ST2CD102J VRD-MN2BD102J VRD-ST2CD102J VRD-MN2BD101J VRD-MN2BD820J VRD-ST2CD102J VRD-MN2BD102J VRD-ST2CD102J VRD-MN2BD102J VRD-ST2EE120J VRD-ST2CD102J VRD-MN2BD151J VRD-MN2BD471J VRD-ST2CD102J VRD-ST2CD472J VRD-ST2CD102J VRD-MN2BD472J VRD-MN2BD102J VRD-MN2BD104J VRD-ST2CD104J VRD-MN2BD103J VRD-ST2CD102J VRD-ST2CD682J VRD-ST2CD222J VRD-ST2CD103J VRD-ST2CD223J VRD-ST2EE470J VRD-ST2CD223J VRD-ST2CD101J VRD-RT2HD271J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J DESCRIPTION AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 100 kohm,1/8W 1 kohm,1/8W 100 kohm,1/8W 1 kohm,1/8W 3.3 kohms,1/8W 100 kohm,1/8W 10 kohm,1/8W 10 kohm,1/8W 1 kohm,1/6W 1 kohm,1/8W 1 kohm,1/6W 100 ohm,1/8W 82 ohms,1/8W 1 kohm,1/6W 1 kohm,1/8W 1 kohm,1/6W 1 kohm,1/8W 12 ohms,1/4W 1 kohm,1/6W 150 ohms,1/8W 470 ohms,1/8W 1 kohm,1/6W 4.7 kohms,1/6W 1 kohm,1/6W 4.7 kohms,1/8W 1 kohm,1/8W 100 kohm,1/8W 100 kohm,1/6W 10 kohm,1/8W 1 kohm,1/6W 6.8 kohms,1/6W 2.2 kohms,1/6W 10 kohm,1/6W 22 kohms,1/6W 47 ohms,1/4W 22 kohms,1/6W 100 ohm,1/6W 270 ohms,1/2W Connector Ass’y,6/10/2Pin Plug,5Pin Plug,8Pin Plug,6Pin Plug,6Pin Plug,10Pin Plug,3Pin Plug,7Pin Plug,8Pin Plug,2Pin Plug,3Pin Plug,2Pin Plug,2Pin Plug,2Pin Connector Ass’y,5/5Pin Connector Ass’y,8/8Pin Connector Ass’y,6/6Pin Connector Ass’y,3Pin Connector Ass’y,7Pin Connector Ass’y,8Pin Connector Ass’y,2Pin Jack,Headphones LCD Display Motor with Chassis [Spindle] Motor with Gear [Sled] Motor with Worm [Turntable Up/Down/Loading] Motor with Pulley [Tape] Remote Sensor,21043TH2 Terminal,Speaker Socket,AC Input Solenoid Ass’y Switch,Push Type [Open/Close] Switch,Leaf/Skeleton Type [Mecha Up] Switch,Push Type [Disc Number] Switch,Push Type [Pickup In] Switch,Leaf Type [Tape 1 Main] Switch,Leaf Type [Tape 2 Main] Switch,Leaf Type [Tape 1 Record] OTHER CIRCUITRY PARTS ! BIM5/CNS4/CNS5 QCNWN0894AWZZ CNP1 92LCONE5P53253 CNP2 92LCONE8P53253 CNP3 92LCONE6P53253 CNP3A 92LCONE6P53254 CNP4 92LCONEAP53253 CNP201 92LCONE3P53253 CNP202 92LCONE7P53253 CNP203 92LCONE8P53253 CNP204 QCNCM035BAWZZ CNP301 92LCONE-3P5268 CNP302 QCNWN1455AWZZ CNP901 QCNCM035BAWZZ CNP902 QCNCM036BAWZZ CNS1A/B QCNWN0891AWZZ CNS2A/B QCNWN0892AWZZ CNS3A/B QCNWN0893AWZZ CNS201 QCNWN0634AWZZ CNS202 QCNWN0635AWZZ CNS203 QCNWN0921AWZZ CNS204 QCNWN0923AWZZ JK601 QJAKM0012AWZZ LCD701 RV-LX0024AWZZ M1 92LMTR1858CASY M2 92LMTR1854BASY M3 92LMTR2037AS1 J J J J J J J J J J J J J J J J J J J J J J J J J J AH AB AC AC AC AC AB AC AC AB AC AE AB AC AG AF AF AK AQ AE AD AF AL AS AP AP M601(257-7) RX701 SO601 SO901 SOLM2(247) SW1 SW2 J J J J J J J AR AG AK AH AH AE AD J J J J J AD AD AE AE AB RMOTM0004AWM1 VHL21043TH2-1 QTANA0801AWZZ QSOCA0209AWZZ RPLU-0002AWZZ QSW-P0004AWZZ QSW-F0001AWZZ SW3 QSW-P0005AWZZ SW4 QSW-F9001AW01 SW605(257-8) 92LM-SW1491A SW606(257-9) 92LM-SW1491A SW607(257-10) 92LM-SW1658A –3– CD-C602,CPC602 NO. PRICE RANK PARTS CODE SW608(257-11) 92LM-SW1658A SW701 92LSWICHT1663T SW702 92LSWICHT1663T SW703 92LSWICHT1663T SW704 92LSWICHT1663T SW705 92LSWICHT1663T SW706 92LSWICHT1663T SW707 92LSWICHT1663T SW708 92LSWICHT1663T SW709 92LSWICHT1663T SW710 92LSWICHT1663T SW711 92LSWICHT1663T SW712 92LSWICHT1663T SW714 92LSWICHT1663T SW715 92LSWICHT1663T SW716 92LSWICHT1663T DESCRIPTION NO. J J J J J J J J J J J J J J J J AB AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC Switch,Leaf Type [Tape 1 Play] Switch,Key Type [Power] Switch,Key Type [Volume Up] Switch,Key Type [Volume Down] Switch,Key Type [Play] Switch,Key Type [Fast Forward] Switch,Key Type [Rewind] Switch,Key Type [Open/Close] Switch,Key Type [Stop] Switch,Key Type [Disc Skip] Switch,Key Type [X-BASS] Switch,Key Type [Function] Switch,Key Type [Band] Switch,Key Type [Memory] Switch,Key Type [Tuning Up] Switch,Key Type [Tuning Down] 235 237 238 239 240 241 242 243 244 245 246 247(SOLM2) 248 248- 1 NGERK0004AWZZ NGERW0006AWZZ NPLYD0001AWZZ NGERK0005AWZZ MLEVP0066AWZZ NGERH0064AWZZ NGERK0003AWZZ LHLDZ1141AWZZ NGERH0065AWZZ NBLTK0029AWZZ 92LN-BAND1318A RPLU-0002AWZZ 92LCOV3037CTS1 ———— J J J J J J J J J J J J J AB AC AB AB AE AD AC AB AB AB AA AH AK — 248- 2 249 249- 1 HDECQ0447AWSA J 92LCOV3037CTS2 J ———— AD AK — Gear,Middle Gear,Drive Rail,Guide Shaft,Guide Cushion Pickup Unit Ass’y Pickup Unit (Not Replacement Item) Gear,Rack Spring,Rack Screw,ø2.6×6mm Screw,ø2×5mm Screw,ø2×3mm Washer,ø1.5×ø3.8×0.25mm Motor with Chassis [Spindle] Motor with Gear [Sled] Switch,Push Type [Pickup In] 249- 2 250 251 252 253 254 255 HDECQ0448AWSA MLIFP0001AWSA JKNBZ0591AWSA JKNBZ0590AWSA JKNBZ0587AWSA JKNBZ0588AWSA JKNBZ0589AWSA J J J J J J J AD AG AG AG AG AF AG 257 92LMECHA3037A 257- 1 92LM-BELT1651B 257- 2 92LMBELT1658A1 257- 3 92LMBELT1658B1 257- 4 92LM-EH1658A 257- 5 92LM-PRA1651A 257- 6 92LM-RPH1746A 257- 7(M601) RMOTM0004AWM1 257- 8(SW605) 92LM-SW1491A 257- 9(SW606) 92LM-SW1491A 257-10(SW607) 92LM-SW1658A J J J J J J J J J J J BH AB AC AC AG AE AM AR AE AE AB 257-11(SW608) 92LM-SW1658A 259 TLABS0058AWZZ 260 TLABS0155AWZZ 261 QLUGP0001AWZZ 262 GDORF0060AWSA 263 GDORF0061AWSA 264 XWHJZ62-09510 265 LANGF0032AWZZ 266 PCUSG0022AWZZ 267 TLABN0086AWZZ J J J J J J J J J J AB AB AC AC AF AF AB AC AB AB 268 92LLABL372C J AB 269 601 602 603 605 606 607 608 609 610 611 612 613 614 615 PCOVZ1013AWZZ XEBSD30P10000 XESSD30P10000 XEBSD30P12000 XEBSF30P12000 LX-JZ0004AWFD LX-JZ0002AWFD LX-EZ0005AWFD XJSSF30P10000 XBPSD26P05JSO LX-TZ0019AFZZ XEBSD26P12000 XJBSF30P08000 XJBSD30P08000 XWHSD32-10130 J J J J J J J J J J J J J J J AB AA AA AA AA AA AA AA AA AB AB AA AA AA AA CD MECHANISM PARTS ! PRICE RANK PARTS CODE 301 302 303 304 305 306 306- 1 NGERH0011AWZZ NGERH0012AWZZ MLEVP0080AWZZ NSFTM0002AWFW 92LMCUSN1524A 92LHPC1MASY ———— J J J J J J AC AC AC AE AD BG — 306- 2 306- 3 701 702 703 704 M1 M2 SW4 NGERH0010AWZZ MSPRC0961AFZZ XBSSD26P06000 XHBSD20P05000 XBBSD20P03000 LX-WZ1070AFZZ 92LMTR1854CASY 92LMTR1854BASY QSW-F9001AW01 J J J J J J J J J AB AA AA AA AA AA AS AP AD AX Front Panel Ass’y — Front Panel (Not Replacement Item) AG Panel,LCD Display AD Cover,Remote Sensor AG Back Board [For U.S.A.] Back Board [For Central America] Back Board [For Canada] AK Side Panel,Left AH Side Panel,Right AP Top Cabinet AM Cover,CD Tray AC Label,UL Caution AA Spring,Cassette Holder Up AE Button,Record [Tape 1] AE Button,Play [Tape 1] AE Button,Rewind [Tape 1] AE Button,Fast Forward [Tape 1] AE Button,Stop/Eject [Tape 1] AE Button,Play [Tape 2] AH Main Chassis AE Button,Stop/Eject [Tape 2] AG Heat Sink AB Spring,Lock Lever AC Lever,Lock AB Roller AM Chassis,Loading AB Lever,Turntable Lock AB Spring,Turntable Lock Lever AM CD Player Base AD Support,Stabilizer AK Stabilizer Ass’y — Stabilizer (Not Replacement Item) AF Magnet AA Support,Magnet AK Turntable AB Guide AB Lever,Change AB Spring,Solenoid AG Chassis,CD Mechanism CABINET PARTS 201 201- 1 92LCAB3037AS1 ———— J 201- 2 201- 3 202 202 HDECQ0446AWSA GCOVA1204AWSA GITAR0427AWSA GITAR0428AWSA J J J J 202 203 204 205 206 207 208 209 210 211 212 213 214 215 217 218 220 221 222 223 224 225 226 228 229 229- 1 GITAR0430AWSA GITAS0035AWSC GITAS0036AWSC GCAB-1046AWSC GCOVA1231AWSA 92LLABL1784F 92LCSPR1596A JBTN-0126AWSA JBTN-0127AWSA JBTN-0128AWSA JBTN-0129AWSA JBTN-0130AWSA JBTN-0131AWSA LCHSM0054AWSA JBTN-0132AWSA PRDAR0131AWFW MSPRD0044AWFJ MLEVP0067AWZZ NROLP0009AWZZ LCHSZ0010AWZZ MLEVP0070AWZZ MSPRC0020AWFJ GCAB-1044AWSA LHLDZ1139AWSA 92LHOLD2037AS1 ———— J J J J J J J J J J J J J J J J J J J J J J J J J 229- 2 229- 3 230 231 232 233 234 PMAGF0001AWZZ 92LSUPT1749D NTNT-0018AWSA LHLDZ1140AWZZ MLEVP0068AWZZ MSPRC0024AWFW LCHSZ0011AWZZ J J J J J J J –4– ! DESCRIPTION Gear,Bevel Gear,Worm Wheel Pulley Gear,Loading Lever,Shift Gear,Cam Gear,Drive Support,Pitch Gear,Turntable Belt,Drive Nylon Band,80mm Solenoid Ass’y Cassette Cover Ass’y,Tape 1 Cassette Cover,Tape 1 (Not Replacement Item) Panel,Cassette Cover,Tape 1 Cassette Cover Ass’y,Tape 2 Cassette Cover,Tape 2 (Not Replacement Item) Panel,Cassette Cover,Tape 2 Damper Button,Stop Button,Function Button,Volume Up/Down Button,X-BASS Button,Power/Function/Tuning Up/Down Tape Mechanism Ass’y FF/REW Belt Belt,Drive [Tape 1] Drive Belt [Tape 2] Head,Erase Pinch Roller Ass’y Head,Record/Playback Motor with Pulley [Tape] Switch,Leaf Type [Tape 1 Main] Switch,Leaf Type [Tape 2 Main] Switch,Leaf Type [Tape 1 Record] Switch,Leaf Type [Tape 1 Play] Label,UL Shinca Jitra Label,UL Team Concepts Terminal,Lug Cassette Holder,Tape 1 Cassette Holder,Tape 2 Washer,ø6.2×ø10×0.9mm Support,Turntable Lock Lever Cushion,Foot Label,Production SER.No. [U.S.A. Only] Label,Serial No. [For Canada/Central America Only] Cover,Wire Screw,ø3×10mm Screw,ø3×10mm Screw,ø3×12mm Screw,ø3×12mm Screw,ø3×12mm Screw,ø3×10mm Screw,ø2.6×10mm Screw,ø3×10mm Screw,ø2.6×5mm Screw,Special Screw,ø2.6×12mm Screw,ø3×8mm Screw,ø3×8mm Washer,Power Transformer PACKING PARTS (For Canada/Central America) SPAKA0196AWZZ SPAKC0733AWZZ J J SPAKC0750AWZZ SPAKP0013AWZZ1 SPAKZ0292AWZZ TLABR1029AWZZ J J J J 92LBAG1460C1 J AN Packing Add.,Left/Right AS Packing Case [For Central America] Packing Case [For Canada] AC Polyethylene Bag,Unit AB Mirror Mat AB Label,Bar Code [For Central America Only] AB Polyethylene Bag,Accessories CD-C602,CPC602 NO. PRICE RANK PARTS CODE DESCRIPTION NO. ACCESSORIES ! QACCD0015AW00 J ! QACCD0020AWZZ J QANTL0007AWZZ TINSE0235AWZZ TINSK0078AWZZ TINSZ0394AWZZ J J J J TINSZ0395AWZZ J TLABZ0529AWZZ TLABZ0530AWZZ RRMCG0103AWSA 92LLID1782A J J J J AM AC Power Supply Cord [For Canada] AN AC Power Supply Cord [For U.S.A./Central America] AK AM/FM Loop Antenna AD Operation Manual [For U.S.A.] Operation Manual [For Canada] AB Quick Guide [For U.S.A./Central America Only] Operation Manual [For Central America] AB Label,Feature,Unit,Tape 1 AB Label,Feature,Unit,Tape 2 AR Remote Control AQ Battery Lid,Remote Control P.W.B. ASSEMBLY (Not Replacement Item) PWB-A1~4 92LPWB3037MANS J PWB-B PWB-C QPWBF0027AWZZ J QPWBF0341AWZZ J — Main/Display/Spacer A/B (Combined Ass’y) AD CD Motor (PWB Only) AB Tray Motor (PWB Only) OTHER SERVICE PARTS UDSKA0004AFZZ J AZ CD Pickup Lens Cleaner CP-C602 SPEAKER BOX PARTS (Front Speaker) 701 702 703 704 705 706 707 SP1,2 92L121-0160 92L051-0068 92L291-0080 92L372-0006 92L351-0321 92L316-0067 92L394-0026 VSP0010PBR36A J J J J J J J J AT AV AH AD AC AP AB AR Net Frame Ass’y Speaker Box Ass’y Cord,Speaker Screw,ø4×12mm Label,Specifications Panel,Duct Port Cushion Speaker,Woofer SPEAKER BOX PARTS (Rear Speaker) (GBOXS0020AWM1) 901 902 903 904 905 SP3,4 92LSRCNF001RS 92LSRCBC002RS 92LSRCSC004RS 92LSRCSW005RS 92LSRCPL009RS VSP0080PBP1CA J J J J J J AP AM AK AB Net Frame Ass’y Bottom Cabinet Cord,Speaker Screw,ø3×12mm Label,Specifications AN Speaker,Woofer 92LSRCBP008RS J 92LSRCPE006RS 92LSRCTP007RS 92L411-0019 92L412-0121 J J J J Packing Add.,Bottom,Rear Speaker Polyethylene Bag,Rear Speaker Packing Add.,Top,Rear Speaker AB Polyethylene Bag,Front Speaker Packing Add.,Top/Bottom,Front Speaker PACKING PARTS –5– PARTS CODE PRICE RANK DESCRIPTION CD-C602,CP-C602 CD-C602 306-2 306 A 306-1 701 306-3 B 304 701 302 704 C 702 702 301 D 303 703x2 E M1 F 305 M2 G 305x2 SW4 H PWB-B 1 2 3 4 Figure 6 CD MECHANISM EXPLODED VIEW –6– 5 6 CD-C602,CP-C602 CD-C602 606 203 A 613 605 PWB-A2 259,260 267(U.S.A.Only) 268 (Canada/ Central America Only) PWB-A1 602x8 601x3 606 606 602 B 202 PWB-A4 LCD701 252 Silicon 261 Grease 255 602 PWB-A3 IC601 C 254 201 253 614 PWB-A4 218 IC921 251 201-1 D Q923 614x2 TAPE MECHANISM 602x6 201-3 209 210 211 213 212 214 E 217 615 250 PT901 257(257-1, 257-2, 257-3, 257-4, 257-5, 257-6, 257-7(M601), 257-8(SW605), 257-9(SW606), 603x2 257-10(SW607), 257-11(SW608)) 615 (Tape Mechanism Assembly) 201-2 F 601x2 262 263 248-1 215 G 249-1 606 249 248-2 H 248 249-2 208 605 204 208 246 Note: Only the unit and consumale parts are supplied as aprts supply for the Tape mechanism. 1 2 3 4 Figure 7 CABINET EXPLODED VIEW (1/2) –7– 5 6 CD-C602,CP-C602 CD-C602 228 609 229 A 229-3 229-2 264 205 605x2 229-1 230 B 224 207 C SW3 222 225 222 222 605x2 206 226 D 222x2 607 265 220 CD MECHANISM E 612 243 244 266 601 614 611 611 245 231 238 221 242 235 222 235 241 232 608 F 269 237 240 SW2 231 G 223 239 610x2 222 234 601 233 603x4 222 H 1 2 3 4 Figure 8 CABINET EXPLODED VIEW (2/2) –8– PWB-C M3 247 (SOLM2) 5 6 CD-C602,CP-C602 CP-C602 BLACK WOOFER SP1(L-CH) SP2(R-CH) RED A 701 B WOOFER SP1(L-CH) SP2(R-CH) C 706 704x4 D SP1(L-CH) SP2(R-CH) E 702 707x2 F G 705 H 703 1 2 3 4 Figure 9 FRONT SPEAKER EXPLODED VIEW (1/2) –9– 5 6 CD-C602,CP-C602 GBOXS0020AWM1 A WOOFER SP3(L-CH) SP4(R-CH) 901 B WOOFER SP3(L-CH) SP4(R-CH) C SP3(L-CH) SP4(R-CH) D 903 E WHITE BLACK 902 F G 904x6 905 H 1 2 3 4 Figure 10 REAR SPEAKER EXPLODED VIEW (2/2) – 10 – 5 6 CD-C602,CP-C602 PACKING OFF THE SET (FOR U.S.A. ONLY) Setting position of switches and knobs Tape Mechanism SPAKP0013AWZZ1 Polyethylene Bag,Unit 92L411-0019 Polyethylene Bag, Front Speaker SPAKA0196AWZZ Packing Add., Left/Right SPAKZ0292AWZZ Mirror Mat AC Power Supply Cord Remote Control Operation Manual Quick Guide FM/AM Loop Antenna P TO Left FR ON T 92LBAG1460C1 Polyethylene Bag, Accessories M O TT O B Feature Label, Tape 1 Feature Label, Tape 2 STOP Right FR ON T FR ON T 92LSRCPE006RS Polyethylene Bag, Rear Speaker P TO T ON FR 92L412-0121 Packing Add., Front Speaker (Top/Bottom) 92LSRCTP007RS Packing Add., Top Rear Speaker TLABR1029AWZZ Bar code Label 92LSRCBP008RS Packing Add., Bottom Rear Speaker SPAKC0733AWZZ Packing Case Not Replacement Item – 11 – CD-C602,CP-C602 —MEMO— – 12 – CD-C602,CP-C602 COPYRIGHT © 1999 BY SHARP COPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any from or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. SHARP CORPORATION Communication Systems Group Quality & Reliability Control Center Higashihiroshima, Hiroshima 739-0192, Japan Printed in Japan A9901-2062NS•HA•M SC • SL