Download Sam4s ER-5100? SERIES Service manual

ELECTRONIC CASH REGISTER
ER-5100 / ER-5140
ER-5115 / ER-5140FP
SERVICE Manual
ELECTRONIC CASH REGISTER
CONTENTS
1.
Precaution Statements
2.
Product Specifications
3.
Installation and Operation
4.
Disassembly and Assembly
5.
Alignment and Adjustment
6.
Troubleshooting
7.
Exploded Views and Parts List
8.
PCB Parts List
9.
Block Diagram
10.
Wiring Diagram
11.
ASIC SCR60K Pin Assignment
12.
Schematic Diagrams
About this Manual
This service manual describes how to perform
hardware service maintenance for the SAM4S
ER-5100 Series Electronic Cash Register.
Notes
Notes may appear anywhere in the manual.
They describe additional information about the
item.
Precaution symbols
. Indicates a Safety Precaution that applies to
this part component.
. Indicates the part or component is an
electro-statically sensitive device. Use caution
when handling these parts.
Acronym
ASIC
ECR
EPROM
ESD
Ext.
F
GND
IC
N.C.
PCB
R..
RAM
ROM
SRAM
T..
Definition
Application for Specific
Integrated Circuit
Electronic Cash Register
Electric Programmable ROM
Electro-statically Sensitive
Device
Extension
Fiscal
Ground
Integrated Circuit
Not Connected
Printed Access Memory
Receive
Random Access Memory
Read Only Memory
Static Random Access
Memory
Transmission
Copyright
ⓒ 2004 by Shin Heung Precision.
All right reserved.
This manual may not, in whole or in part, be
copied, photocopied, reproduced, translated or
converted to any electronic or machine readable
from without prior written permission of Shin
Heung Precision .
SAM4S ER-5100 SERIES
ER-5100 Service Manual
March 2004.
V1.0
Printed in KOREA
Overview of this System ECR
This service manual provides the technical information for many individual component systems, circuits and gives an
analysis of the operations performed by the circuits. If you need more technical information, please contact our service
branch or R&D center. Schematics and specifications provide the needed information for the accurate troubleshooting.
All information in this manual is subject to change without prior notice. Therefore, you must check the correspondence of
your manual with your machine. No part of this manual may be copied or reproduced in any form or by any means, without
the prior written consent of Shin Heung Precision
Note: Before using this System Electronic Cash Register (ECR) for the first time, leave it powered on in the REG
mode for at least twenty-four hours. This allows the Ni-MH battery, which maintains the memory of the
SECR while the power is off, to charge completely.
1 Precaution Statements
Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as
electrical shock.
1-1 Safety Precautions
1. Be sure that all of the built-in protective devices are
replaced. Restore any missing protective shields.
2. When reinstalling the chassis and its assemblies, be
sure to restore all protective devices, including
nonmetallic control knobs and compartment covers.
3. Make sure there are no cabinet openings through
which people-particularly children-might insert
fingers and contact dangerous voltages.
Such openings include excessively wide cabinet
ventilation slots and improperly fitted covers and
drawers.
4. Design Alteration Warning:
Never alter or add to the mechanical or electrical
design of the ECR. Unauthorized alterations might
create a safety hazard. Also, any design changes or
additions will void the manufacturer’s warranty.
5. Components, parts and wiring that appear to have
overheated or that are otherwise damaged should be
replaced with parts that meet the original
specifications. Always determine the cause of
damage or over- heating, and correct any potential
hazards.
SAM4S ER-5100 SERIES
6. Observe the original lead dress, especially near the
following areas: sharp edges, and especially the AC
and high voltage supplies. Always inspect for
pinched, out-of-place, or frayed wiring. Do not
change the spacing between components and the
printed circuit board. Check the AC power cord for
damage. Make sure that leads and components do
not touch thermally hot parts.
7. Product Safety Notice:
Some electrical and mechanical parts have special
safety-related characteristics which might be obvious
from visual inspection.
These safety features and the protection they give
might be lost if the replacement component differs
from the original - even if the replacement is rated
for higher voltage, wattage, etc.
Components that are critical for safety are indicated
in the circuit diagram by shading, ( ) or ( ).
Use replacement components that have the same
ratings, especially for flame resistance and dielectric
strength specifications. A replacement part that
does not have the same safety characteristics as the
original might create shock, fire or other hazards.
1-1
1 Precaution Statements
1-2 Servicing Precautions
WARNING: First read the-Safety Precautions-section of this manual. If some unforeseen circumstance creates
a conflict between the servicing and safety precautions, always follow the safety precautions.
WARNING: An electrolytic capacitor installed with the wrong polarity might explode.
1. Servicing precautions are printed on the cabinet.
Follow them.
2. Always unplug the units AC power cord from the AC
power source before attempting to:
(a) Remove or reinstall any component or assembly
(b) Disconnect an electrical plug or connector
(c) Connect a test component in parallel with an
electrolytic capacitor
3. Some components are raised above the printed circuit
board for safety. An insulation tube or tape is
sometimes used. The internal wiring is sometimes
clamped to prevent contact with thermally hot
components. Reinstall all such elements to their
original position.
4. After servicing, always check that the screws,
components and wiring have been correctly
reinstalled. Make sure that the portion around the
serviced part has not been damaged.
5. Check the insulation between the blades of the AC
plug and accessible conductive parts (examples:
metal panels and input terminals).
6. Insulation Checking Procedure:
Disconnect
the power cord from the AC source and turn the
power switch ON. Connect an insulation resistance
meter (500V) to the blades of AC plug.
The insulation resistances between each blade of the
AC plug and accessible conductive parts (see above)
should be greater than 1 megohm.
7. Never defeat any of the B+ voltage interlocks.
Do not apply AC power to the unit (or any of its
assemblies) unless all solid-state heat sinks are
correctly installed.
8. Always connect an instrument’s ground lead to the
instrument chassis ground before connecting the
positive lead ; always remove the instrument’s ground
lead last.
1-3 Precautions for Electrostatically Sensitive Devices (ESDs)
1. Some semiconductor (solid state) devices are easily
damaged by static electricity. Such components are
called Electrostatically Sensitive Devices (ESDs);
examples include integrated circuits and some fieldeffect transistors. The following techniques will reduce
the occurrence of component damage caused by static
electricity.
2. Immediately before handling any semiconductor
components or assemblies, drain the electrostatic
charge from your body by touching a known earth
ground. Alternatively, wear a discharging wrist-strap
device. (Be sure to remove it prior to applying power
- this is an electric shock precaution.)
3. After removing an ESD-equipped assembly, place it
on a conductive surface such as aluminum foil to
prevent accumulation of electrostatic charge.
4. Do not use Freon-propelled chemicals. These can
generate electrical charges that damage ESDs.
5. Use only a grounded-tip soldering iron when
soldering or unsoldering ESDs.
6. Use only an anti-static solder removal device. Many
solder removal devices are not rated as anti-static;
these can accumulate sufficient electrical charge to
damage ESDs.
1-2
7. Do not remove a replacement ESD from its protective
package until you are ready to install it. Most
replacement ESDs are packaged with leads that are
electrically shorted together by conductive foam,
aluminum foil or other conductive materials.
8. Immediately before removing the protective material
from the leads of a replacement ESD, touch the
protective material to the chassis or circuit assembly
into which the device will be installed.
9. Minimize body motions when handling unpackaged
replacement ESDs. Motions such as brushing clothes
together or lifting a foot from a carpeted floor can
generate enough static electricity to damage an ESD.
SAM4S ER-5100 SERIES
2 Product Specifications
Specifications are correct at the time of printing. Product specifications are subject to change without notice. See below
for product specifications.
2-1 Specifications
Item
Description
AC Power Source
Power Consumption
Remark
AC 120V, 60Hz
USA
AC 230V, 50Hz
Europe
35W max
USA and Europe
1 pair, 9-pin Dot matrix
R/J Printer
Printing speed; 3.0 lines per second
Receipt / Journal paper sensor
Processor
SCR60K
Memory
* Main PCB
Default : SRAM(KM681000*1) : 128kbyte
EPROM(27C010*1) : 128kbyte
or EPROM(27C020*1) : 256kbyte
Ext.
: SRAM(KM681000*1) : 128kbyte
* Fiscal(ER-5140FP)
Default : EPROM(27C512*1) : 64kbyte
Ext.
: EPROM(27C010*1) 128kbyte
Data Storage
60 Days
Battery
Ni-MH,3.6V,70mAh
Charging time
Display
Keyboard
When battery fully
charged
: 24 hours
Front
: 10-digit display (Front display)
Rear
: 10-digit display (Real display)
160-Key
ER-5100
90-Key
ER-5140/5140FP
60-Key
Default
Interface
Ext.
Drawer
Packing Carton
ER-5115
- RS-232C
: 1 port
(Optional Board I)
or Modular Jack
: 1 ports
(Optional Board I)
- RS-232C
: 2 port
(Optional Board II)
5C5B
USA
8C4B
Europe
EURO
8C7B
Weight
: 9.3 Kg
Dimensions
: 400(W) x 450(L) x 111(H)
Weight
: 17.6 Kg
Dimensions
: 498(W) x 564(L) x 384(H)
When packed
millimeters
millimeters
Equipment specifications are subject to change without notice.
SAM4S ER-5100 SERIES
2-1
2 Product Specifications
2-2 Dimensions
305
40
0
2-2
5
45
SAM4S ER-5100 SERIES
2 Product Specifications
2-3 Communication Interfaces
2-3-1 Serial Interfaces and Port Locations
Figure 2-1. RS-232C Interface Locations
2-3-2 Pin Descriptions for Serial Interfaces (Optional P.C.B.)
Figure 2-2. Pin Number Assignment
Table 2-1. Pin Descriptions and Signals of Serial Ports
Serial port #1
Serial port #2
Pin #
Signal
Pin #
Signal
Pin #
Signal
1
N.C.
1
DTR
1
DTR
2
RxD
2
N.C.
2
N.C.
3
TxD
3
TxD
3
TxD
4
DTR
4
N.C.
4
N.C.
5
GND
5
RxD
5
Rxd
6
N.C.
6
GND
6
gnd
7
N.C.
8
DTR
9
N.C.
SAM4S ER-5100 SERIES
2-3
2 Product Specifications
Memo
2-4
SAM4S ER-5100 SERIES
3 Installation and Operation
3 Installation and Operation
This chapter describes the method for installing the ECR system and shows the locations of the various feature items.
3-1 System configuration
Figure 3-1. Terminal System
3-1-1 Terminator Specification
Figure 3-2. Terminator
Figure 3-4. Cable for Serial Port 2
3-1-2 Cable Specifications
Figure 3-3. Cable for Serial Port 1
SAM4S ER-5100 SERIES
3-1
3 Installation and Operation
3-2 Installation
WARING: When connecting the keyboard to the Main PCB, made sure the membrane sheet is shaped as in
figure 3-6(a), below. If the membrane is shaped as in Figure 3-6(b), the keyboard may malfunction.
Figure 3-6. Membrane Shape
3-2-1 Ribbon Cassette Installation
Figure 3-7. Ribbon Cassette
1.Before inserting ribbon cassette②, turn. knob①(see Figure 4-4) counterclockwise to prevent twisting the
ribbon.
2.After inserting the ribbon cassette② at the center③ of the printer, turn the knob ① counterclockwise again
to make sure the ribbon moves freely in the cassette
3-2
SAM4S ER-5100 SERIES
3 Installation and Operation
3-2-2 Receipt / Journal Paper Insertion
Figure3-8 Folding Paper for Insertion
Figure3-9 Inserting the paper
Figure3-10 Inserting the Journal Paper
1. Using a new roll of paper, unroll the paper about 150mm and fold the paper as shown in Fig 3-8
2. Insert fold paper into the chute ② of the printer. While holding the lever ① down,
pull the paper out until the fold point ③ is completely out of the printer. And turn the knob ④
like an arrow. (Fig 3-9)
3. Cut the receipt paper.
4. Insert the journal into paper the silt ③ of the rewind spindle. Wind the spindle three or four
times.
5. Push end disk ⑥ into the spindle as shown in Fig 3-10.
6. Insert the spool to the printer part ⑤.
7. When the journal paper is loose, rewind the spindle to tighten the paper.
3-3 Operation
Note: Before using this Electronic Cash Register (ECR) for the first time, leave it powered ON in the REG mode for at
least twenty-four hours. This allows the Ni-Cad battery, which maintains the ECRs memory while the power is
OFF, to fully charge.
3-3-1 ECR Features
1
4
3
2
5
3
6
8
①
②
③
④
⑤
Cover Printer
Impact dot Printer
Keyboard
Drawer
Drawer Lock Key
SAM4S ER-5100 SERIES
7
⑥
⑦
⑧
⑨
Serial Interface Port
Serial 1 (D-sub 9 Pin) *2
Serial 2 (Modular Jack) *1
Mode Key Switch
Rear Display
Clerk Key
3-3
3 Installation and Operation
3-3-2 Mode switch
This position of the Key in the Mode Switch determines the action of the SECR. Table 3-1 shows the various modes
that are available.
Table 3-1. ECR Modes
Mode
Function
VOID
Cancel operation
OFF
Operation Stop
REG
Sales operation
X
X-level report generation
Z
Z-level report generation
P
Program mode
MC
Manager control
Figure 3-14. Mode Switch
3-3-3 Keyboard Matrix
3
The ER-5100, ER-5140, ER-5115 and ER-1551F ECRs offer three different types of keyboards; 160-key, 90-key or
60-key as shown in Table 3-2.
Table 3-2. Keyboard Types
SAM4S ER-5100 SERIES
Model
Keys
Type
ER-5100
160
Membrane (Flat)
ER-5140
90
Membrane
ER-5115
60
Membrane
Er-5115F/FP
60
Membrane
3-4
4 Disassembly and Assembly
This chapter describes the Disassembling and Reassembling procedures for ER-5100, electronic cash registers.
WARNING: This ECR contains electro-statically sensitive devices. Use caution when handling any components.
4-1 Disassembly
Caution: Disconnect the ECR from the external power source before Disassembly.
Note: The following directions are given for the ER-5100. differences between the models are identified in the text.
4-1-1 Upper Case Disassembly
1.
2.
3.
4.
Lift off the Printer cover.
Remove three screws ((B-6) and (B-11))on the
Upper Case and loft it up.
Remove the red and the white connectors on the
main PCB.
Remove the Upper Case.
4-1-2 ERP-400 Printer Disassembly
1.
2.
3.
Remove the two screws, ⓑ, and remove the
Ribbon Frame, B, from the Lower Frame
assembly I, as shown in the drawing.
Remove the four screws, ⓒ, and separate the
Upper Frame Assembly, C, from the Lower
Frame assembly, I. Pull the Upper Frame
assembly in the direction shown in figure 4-2.
PULLING
DIRECTION
UP
Remove the four screws ⓐ on the Upper Frame
Assembly, C, and remove the Cover, A. See
Figure 4-1, below.
FRONT
Figure 4-1. Printer Disassembly
SAM4S ER-5100 SERIES
Figure 4-2. Separating Upper Frame from the Lower
Frame.
4-1
4 Disassembly and Assembly
4.
Turn the upper Frame Assembly, down and
remove the three screws, . Remove the Stamp
Paper Guide Assembly D, from the Upper Frame
Assembly C.
5.
Remove the left-side screw, , on the Platen Paper
Guide, E. This screw connects the Platen Paper
Guide Assembly E, -to Stamp Paper Guide
Assembly, D. See figure 4-4, below.
e
E
D
Figure 4-3. Stamp Paper Guide Removal
Figure 4-4. Platen Guide Removal
4-2 Assembly
Caution: Adjust the Head Gap )see Alignment and Adjusts chapter) before returning the ECR to the owner.
4-2-1 ERP-400 Printer Assembly
1.
2.
3.
Position the Platen Paper Guide Assembly, E, on
the Stamp Paper guide Assembly, D, and replace
the screw -ⓔ (see Figure 4-4, above).
With the Upper Frame Assembly C, upside-down,
position the Stamp Paper Guide Assembly, D, and
replace the three screws –ⓓ (see Figure 4-3,
above).
Position the Upper Frame Assembly, C, on the
Lower Frame Assembly, I, and replace the four
screws ⓒ (see Figure 4-5, to the fight).
Caution: Locate Stamp Pusher ⓕ on the hatched
area as shown in the figure.
4.
5.
4-2
Position the Ribbon Frame, B, on the Lower
Frame Assembly, I, and replace the two screws
ⓑ (see Figure 4-1, above)
Position the cover, A, on the Upper Frame
Assembly, C, and replace the four screws_-ⓐ.
C
F
Hatched
area
D
Figure 4-5. Stamp Pusher Position
SAM4S ER-5100 SERIES
4 Disassembly and Assembly
4-2-2 Upper Case Assembly
1.
2.
3.
Position the Upper Case so that the connectors
are within reach of the Main PCB. Replace the
red and the white connectors.
Position the Upper Case on the Lower Case and
replace the three screws ((B-6) and (B-11))
Replace the Printer Cover.
SAM4S ER-5100 SERIES
4-3
4 Disassembly and Assembly
Memo
4-4
SAM4S ER-5100 SERIES
5 Alignment and Adjustments
This chapter describes the methods for aligning and adjusting components in this ECR.
5-1 Printer Adjustments
5-1-1 Head Gap Adjustment
1.
2.
3.
4.
5.
6.
Assemble the Upper Frame Assembly, A, to the
Lower Frame Assembly, I and loosely fox
screws .
Wind the Head Gear counterclockwise to;
move the Head to the right end of the Platen
Guide.
Insert the Gap Gauge (width 0.5mm) and
tighten the Head and Platen. Tighten the
screws .
Wind the Head Gear counterclockwise again
and move the Head to the left end of the Platen
Guide.
Insert the Gap Gauge (0.5mm) and tighten the
screws.
After tightening al screws , apply Nej-Lock (a
brand of grease) on each of the four screws .
5-1-2 Roll Paper Near-End Detector
(Type 1 Paper Sensor)
5-1-2-(a) Adjustment Point
ADJUSTMENT SCALE
#5
#4
#3
#2
#1
ADJUSTMENT POINT
BRACKET P/END
SLIDE BRACKET
(SET FOR PAPER THICKNESS = 0.075MM)
Figure 5-2. Adjustment Point
As Figure 5-2 shows, the slide bracket is set at
Adjustment Scale #3. This is the appropriate scale for the
recommended paper thickness (0.075mm).
The accuracy of the Near-End Detector depends on the
Adjustment Scale setting and the Roll Paper Winding
Core diameter. The only paper approved for use in this
ECR has the following characteristics:
Table 5-1. Roll Paper characteristics
Characteristic
Paper Thickness
Figure 5-1. Head Gap Adjustment
SAM4S ER-5100 SERIES
Paper Width
Measurement
0
075mm
44.5mm ± 0.5mm
5-1
5 Alignment and Adjustments
The relationship between the Adjustment Scale and the
paper remnant remaining on the core is as shown in
figure 5-3.
Winding Core may pull out of its holder due to the
paper sticking to Winding Core, If the Winding
Core pulls out of its holder, the Paper Sensor may
indicate an inaccurate remnant length.
Remnant of (m):
5-1-3 Clearing a Paper Jam
5
4
3
2
1
5-1-3-(a) Paper Jamming Causes
1.
#1 #2 #3 #4 #5
Figure 5-3. Relationship: Adjustment Scale to
Remnant Length
Note: figure 5-3 applies only when using SAM4S
recommended papers.
Figure 5-4 shows the relationship between the
Adjustment Scale and the outer diameter of the
Winding Core.
Adjusting Scale:
2.
5-1-3-(b) Clearing Procedure
Caution: Always disconnect the power cord from
the power outlet before working on the
Paper Cutter.
1.
2.
3.
4.
#5
#4
#3
#2
#1
When more than two papers have entered the
paper path.
When paper cutting remnants remain in the
paper exit space.
Open the Printer cover and remove the AutoCutter Cover 2.
Remove all jammed paper at the Auto-Cutter.
Replace Auto-Cutter Cover 2 and close the
Printer cover.
The Auto-Cutter will operate as soon as power
is restored to the ECR. After cutting once, the
Auto-Cutter goes to its normal state.
10 15 20 25 30
Outer diameter of paper winding core (Φ :mm )
D:
d:
Outer Diameter
Inner Diameter
Figure 5-4. relationship: Adjustment Scale to
Winding core diameter
Note:
1.
2.
5-2
When using roll paper other than SAM4S
recommended paper, the roll paper remnant
lengths will differ.
When using roll paper with a red end mark, the
SAM4S ER-5100 SERIES
6 Reference Information
This chapter describes the methods for determining the source of malfunctions in this ECR.
6-1 Troubleshooting
Key Board Problem
Key Input Failure
1. Check the fuse on the Main PCB.
2. Check all Voltage states.
3. Check/Change the related circuit
(IC9 ~IC11) on the Main PCB.
Specific Key
Buzzer
Failure
Malfunction
1. Check the affected keys and the data
bus.
2. Check the diodes (D16~D35)
1. Check the related circuit with the
buzzer(Q4,Q17,IC2,R10,R12,R23,R
24,R100,CC3,Buzzer)
4. Check whether the Printer (ERP400) is out of order.
Drawer Failure
Drawer does not
Automatically open
1. Check the drawer Solenoid and the connector (both the ECR side and the Drawer
side.
2. Check the manual open and closed states using the Drawer Key.
3. Check the IC4,TA3,TA4 and the related circuit on the Main PCB.
SAM4S ER-5100 SERIES
6-1
6 Troubleshooting and Test Procedure
Printer failure
Motor, Stamp, Auto-cutter
Printer head failure
Or Paper feed Failure
1. Check whether the Printer is out of
order.
2.
Check whether the harness
(CN7~CN9) are disconnected.
3. Check TA1 to TA4 and related
circuits on the Main PCB.
1. Check the Head Pin and the Coil.
2.
Check whether the harnesses
(CN7~CN9) are disconnected.
3. Check or change the TA1~TA4 and
the related circuits on the Main PCB.
4. Check whether the paper jam of the
ribbon is twisted.
Receipt/Journal Paper
Sensing Failure
1. Check whether the dummy of the
Paper Near End Sensor (Optional
Item) is not working.
2. Check the Spring of the Sensor.
3. Check the switch operation status of
the Sensor.
4. Check the wire soldering state.
5. Check the connection between the
Main PCB and the Printer.
Real Time Clock Failure
Check the IC8, CC35, CC36 and X2
6-2
SAM4S ER-5100 SERIES
6 Troubleshooting and Test Procedure
Front/Rear(Window/Turret)
Display Failure.
1. Check/change the solder points and the connection harness of the
Window Display PCB.
2. Check the CN6 connection harness on the Main PCB.
3. Check/change the related circuits on the Main PCB.
4. Check the HV5812P and the Digitron on the Display PCB and Turret
PCB.
Mode Key failure
1. Check the key-locked status and the connector insertion in the lock.
2. Check the RA3 on the Main PCB.
Serial 1,2(Optional)
Failure
1. Check the Cable connection with the CN18.
2. Check the solder points on Optional PCB (IC14,Q15 and Q16) and
the related circuits.
3. Check the Bead Wire between the Main PCB and the Optional PCB.
4. Do Loop Back Test with the male D-sub 9Pin connected pin #2 and
#3.
SAM4S ER-5100 SERIES
6-3
6 Troubleshooting and Test Procedure
Modular jack
failure.
1. Check whether the Cable is short, open or etc.
2. Check the connection status between the CN19 and the cable.
3. Check the IC4,Q15,Q16 and the related circuit on the Optional PCB.
4. Check the Bead wire between the Main PCB and Optional PCB.
System failure:
System does not operate
When all clear
1. Confirm input voltage is 120V/230V
2. Check the fuse on Main PCB and each output voltage.
3. Check the contact of the mode switch connector state..
4. Check whether the FPC of Key Board is connected or not.
5. Check Whether the Printer (ERP-400) is out of order.
6-4
SAM4S ER-5100 SERIES
6 Troubleshooting and Test Procedure
6-2 Change the ASIC SCR60K (IC4)
6-2-1 When change the IC4, follow next procedure if the IC4 or out of order certainly
1.
Cut the ASIC-side end of the top of ASIC’s pin with a sharp-tip knife, one by one by one carefully. There may be
some Pattern under the IC4, so it is necessary that you cut carefully them.
Knife
SEC
627D
SCR6CK
Cutting Direction
2.
After cutting, desolder the lead dummy at the pins using a shield wire or flux.
Shield Wire / Flux
SEC
627D
SCR6CK
3.
4.
5.
Then remove the pins one by one the soldering iron.
Desolder the lead dummy on the PCB one more time before soldering the new ASIC SCR60k.
Take the Position of SCR60K on the Land of the Main PCB.
6. Solder the 4 points first like first like the left side of the following Figure.
SAM4S ER-5100 SERIES
6-5
6 Troubleshooting and Test Procedure
7.
Solder the IC4 one top to bottom with much lead under the PCB erected.
SEC
627D
SCR6CK
8.
9.
Desolder the lead dummy around the end pin of the square using a shield wire of Flux liquid.
When using Flux liquid, after paint the Flux liquid and then desolder the lead dummy.
Shield Wire / Flux
SEC
627D
SCR6CK
6-6
SAM4S ER-5100 SERIES
6 Troubleshooting and Test Procedure
6-3 Test Procedure
6-3-1 Initial Clear Procedure
1.
2.
Turn key to P-Mode.
Unplug Register.
3.
4.
Hold down the SULTL on keyboard and plug
in the Register, again.
The Register issues an Initial Clear receipt.
3.
4.
Hold down the Key 00 on the Key board, turn.
The Register issues an All Clear receipt.
6-3-2 All Clear
1.
2.
Turn the Mode Key to S-Mode.
Turn off the power.
5
6
CHECK
2
3
SBTL
00
.
CASH
USE THIS KEY FOR ALL CLEAR PROCEDURE
REGARDLESS OF WHAT KEY FUNCTION ID
PROGRAMMED AT THAT LOCATION
6-3-3 Loop Back Connections
1.
Turn the Mode Key to S-Mode.
7
CASH
For the jig for the communication test
… Serial 1, serial 2 (Main PCB, D-sub 9)
TxD (3) ---- RxD (2)
…
Serial 3, serial 4 (Option PCB, Modular)
TxD (3) ---- RxD (5)
6-3-4 Test
1.
2.
Turn the Mode Key to S-Mode.
Enter the one key of the following code, and enter the Key CASH.
CODE
FUNCTION
1
Printer the Several Characters and Display 0~1 and the Several Characters.
2
Test the Key Board.
3
Test the Mode Key Switch.
4
Print the EPROM version and the Check Sum.
5
Test the Display (Display the
6
Print the H Pattern.
SAM4S ER-5100 SERIES
).
6-7
6 Troubleshooting and Test Procedure
Memo
6-8
SAM4S ER-5100 SERIES
7 Exploded Views and Parts List
7-1 Main Set
7-1-1 Exploded View
Figure7-1 Total Disassembly
SAM4S ER-5100 SERIES
7-1
7 Exploded Views and Parts List
7-1 Main Set
7-1-2 Parts List
Figure7-2 Cover Printer Assembly
7-1-2-(a) Cover Printer Assembly
No.
A
Parts No.
JK97-00141E
Description / Specification
MEA-COVER PRINTER
Q`ty
1
Design-Location
Serviceable
N
A-1
JK75-10391A
MEC-LOCK:ER-5100,-,-
1
Y
A-2
JK72-40223A
PMO-WINDOW JOURNAL:PMMA
1
Y
A-3
JK97-01069A
MEA-COVER PRINTER:ER-5100,BASIC,WORLD
1
Y
A-4
JK70-10323A
IPR-PLATE CLIP:ER-100,SWP,T0.5,-
1
Y
7-2
Remark
SAM4S
SAM4S ER-5100 SERIES
7 Exploded Views and Parts List
7-1 Main Set
7-1-2 Parts List
Figure7-3 Case Upper Assembly
7-1-2-(b) Case Upper Assembly
No.
B-1
B-2
Parts No.
JK72-40356A
Description / Specification
PMO-WINDOW DISPLAY:ER-5100,STANDARD
Q`ty
1
Design-Location
Serviceable
Y
JK72-40356B
PMO-WINDOW DISPLAY:ER-5115/40,STANDARD
1
Y
JK72-40356D
PMO-WINDOW DISPLAY:ER-5140F,SEPOL
1
Y
JK72-40356E
PMO-WINDOW DISPLAY:ER-5115/40,ROC
1
Y
JK72-40356F
PMO-WINDOW DISPLAY:ER-5100,ROC
1
Y
JK72-40920A
PMO-WINDOW DISPLAY:ER-51XX,CRS
1
Y
JK72-40357A
PMO-COVER MODE S/W:ER-5100
1
Y
JK72-40357B
PMO-COVER MODE S/W:ER-5115
1
Y
JK72-40357C
PMO-COVER MODE S/W:ER-5140
1
Y
Y
JK72-40357D
PMO-COVER MODE S/W:ER-5115F
1
JK72-40357E
PMO-COVER MODE S/W:ER-5140F
1
Y
JK72-40357F
PMO-COVER MODE S/W:ER-5100F
1
Y
JK72-40357G
PMO-COVER MODE S/W:ER-5140FI
1
Y
JK72-40357H
PMO-COVER MODE S/W:ER-5115G/SAN
1
Y
Y
JK72-40357J
PMO-COVER MODE S/W:ER-5100G/SAN
1
JK72-40357K
PMO-COVER MODE S/W:ER-5100/SAN
1
Y
B-3
6002-000319
SCREW-TAPPING:PH,+,2,M3,L8,ZPC(YEL),SM20
2
Y
B-4
JK70-10004A
IPR-BRKT MODE_S/W:SBHG-1,T1,-
1
Y
B-5
6002-000319
SCREW-TAPPING:PH,+,2,M3,L8,ZPC(YEL),SM20
2
Y
B-6
6002-000172
SCREW-TAPPING:PH,+,2S,M4,L15,PASS,STS304
3
Y
B-7
JK96-00115A
ELA ETC-MODE S/W:SER-6500
1
Y
B-8
JK72-40359A
PMO-WINDOW TURRET:ER-5100,PC,D/BLU,HB,-
1
Y
B-9
JK92-01231A
PBA TURRET:ER-350F/5100/5200,10G
1
Y
B-10
JK72-40358A
PMO-TURRET BODY:ER-5100,ABS,IVR,V0,-
1
Y
B-11
6001-000367
SCREW-MACHINE:FH,+,M4,L10,NI PLT,SM20C,-
1
Y
B-12
JK70-40305A
ICT-SHAFT MOLDING:SUM 24L,FISCAL
1
Y
JK72-40352A
PMO-CASE UPPER;ER5100
1
Y
JK72-40352B
PMO-CASE UPPER;ER5115F,FISCAL
1
Y
JK92-01230A
PBA SUB-DISPLAY:ER-5100/5200,STD
1
Y
B-13
B-14
SAM4S ER-5100 SERIES
Remark
Fiscal only
7-3
7 Exploded Views and Parts List
7-1 Main Set
7-1-2 Parts List
Figure7-4 Case Lower Assembly
7-1-2-(e) Case Lower Assembly
No.
Parts No.
E-1
6002-000209
E-2
JK73-40201A
RMO-PRINTER:NR,BLK
4
Y
E-3
JK59-10511A
UNIT-PRINTER ASS'Y:ERP-400,ENGLISH
1
Y
E-4
JK75-10383A
MEC-RIBBON CASSETTE:ERC-18
1
Y
E-5
JK39-40021A
CBF HARNESS:VLI05,330/130
1
Y
E-6
6001-000618
SCREW-MACHINE:PH,+,M4,L8,ZPC(YEL),SM20C,
1
Y
E-7
JK72-40353A
PMO-CASE LOWER:ER-5100,ABS,IVR,V0,-
1
Y
E-8
JK92-00130F
PBA MAIN-FISCAL BOAR;ER-5115F
1
Y
JK72-40360A
PMO-COVER FRONT:ER-5100,ABS,IVR,V0,-
1
Y
E-9
Description / Specification
SCREW-TAPPING:RWH,+,2,M3,L17.5,ZPC(YEL),
Q`ty
4
Design-Location
Serviceable
Remark
Y
JK72-40361A
PMO-COVER CLERK KEY:ER-5100
1
Y
OPTION
JK96-00114A
ELA HOU-CLERK ASSY;ER-5100
1
Y
OPTION
JK39-10002A
CBF-POWER CORD: AUSTRALIA
1
Y
JK39-10003A
CBF-POWER CORD: USA
1
Y
JK39-10008A
CBF-POWER CORD: UK
1
Y
JK39-10501A
CBF-POWER CORD: EUROPE
1
Y
E-12
JK70-10002A
IPR-BRKT CASING:SBHG-1,T1.6,-
1
Y
E-13
6002-000171
SCREW-TAPPING:PH,+,2S,M4,L10
1
Y
E-14
JK70-10417A
IPR-GROUND PLATE:SECC,T1,-
1
Y
E-10
E-11
7-4
SAM4S ER-5100 SERIES
7 Exploded Views and Parts List
7-1 Main Set
7-1-2 Parts List (Continue)
7-1-2-(e) Case Lower Assembly (Continue)
No.
Parts No.
E-15
6006-000187
E-16
E-17
E-18
Description / Specification
Q`ty
Design-Location
Serviceable
SCREW-ASS'Y MACH:WT,BH,+,M4,L6
1
Y
6002-000174
SCREW-TAPPING:PWH,+,2,M3,L10
2
Y
6006-000195
SCREW-ASS'Y TAPP:WS,BH,+,M4,L10,ZPC(YEL)
2
Y
JK26-00015A
TRANS-POWER:USA: 120V 60Hz
1
Y
JK26-00014A
TRANS-POWER:EUROPE: 230V 50Hz
1
Y
E-19
JK72-40330A
PMO-ROLLER PAPER/END:POM
2
Y
E-20
JK72-40389A
PMO-HOLDER COVER/PRT:ER-5100,ABS,IVR
1
Y
E-21
6002-000174
SCREW-TAPPING:PWH,+,2,M3,L10
1
Y
E-22
JK92-01054A
PBA MAIN-CLK/OPTION;ER-5100,WO
1
Y
E-23
6002-000174
SCREW-TAPPING:PWH,+,2,M3,L10
4
E-24
JK39-40306D
CBF HARNESS;ER-4615FP,-,UL1007
1
CN7,CN8
Y
E-25
JK39-40306C
CBF HARNESS;ER-4615FP,-,UL1007
1
CN9
Y
E-26
JK64-10301A
PMO-KNOB PAPER/END:POM,-,BLK,T2
2
Y
E-27
6107-000127
SPRING-ES:PI0.3,D3.7,L10.8
2
Y
Y
E-28
6003-000221
SCREW-TAPTITE:PWH,+,S,M4,L8,ZPC(YEL)
2
Y
E-29
JK70-10384A
IPR-BRKT PAPER/END:SECC,T1.5
2
Y
E-30
6002-000175
SCREW-TAPPING:PWH,+,2,M3,L8,ZPC(YEL)
2
Y
E-31
JK70-10385A
IPR-BRKT SLIDE:SECC,T1.5
2
Y
E-32
6001-000496
SCREW-MACHINE:PH,+,M2,L12,ZPC(YEL)
2
Y
E-33
3405-000103
SWITCH-MICRO:125V,100Ma,25gf,SPST
2
Y
E-34
JK39-40303M
CBF-HARNESS:2P,630MM,WHT,1061,#26
1
Y
E-35
6003-001149
SCREW-TAPTITE:PWH,+,S,M4,L10,ZPC(YEL)
1
Y
E-36
JK60-00001A
SCREW-ASSY TAPTITE:-,SWRCH18A,M3,L8
2
Y
E-37
JK39-40011A
CBF HARNESS:ER-350,-,UL1015,250MM
1
Y
E-38
JK39-40303G
CBF-HARNESS:2P,355MM,RED,1007,#26
1
E-39
JK39-40200A
CBF HARNESS;ER-250,FLAT,UL1007
1
DRAWER
Y
E-40
JK39-40302C
CBF HARNESS;ER-350,-,UL1007,18
1
COMPULSORY
Y
SAM4S ER-5100 SERIES
Remark
Y
7-5
7 Exploded Views and Parts List
7-2 Printer (ERP-400)
7-2-1 Exploded View
51
39
40-1
39-3
39-6
40
42
39-4
39-2
39-1
41
39-5
51
40-2
49
38
27
36
51
54
59
60
51
28
29
29-4
36-7 36-4
36-5
29-1 29-3
29-2
36-3
54
37
47
32
36-2
26
37
36-1
33-1
31
47
36-6
33
51
26-1
35
30-2
34-2
34-3
34
33-2
26-2
30-3
30-1
30
26-4
34-5
26-3
34-1
24
20
58
34-4
18
35
6
57
44
51
25
24-1
6-3
24-2
6-1
13
24-3
24-4
18-1
47
53
18-3
21
22
18-6
44
18-2
12
18-4
18-6
6-2
6-4
11-4
3
46
48
43
11-2
52
18-5
44
19
11-1
18-7
24-5
51
11-4
54
11-3
4
45
5
11
52
14
23
44
51
1
7
50
16
17
16-4 16-7
51
56
51
8
54
15
10
2
50
55
51
9
16-5
16-3
56
47
16-6 16-2
16-1
16-8
51
Figure7-5 Printer (ERP-400)
7-6
SAM4S ER-5100 SERIES
7 Exploded Views and Parts List
7-2 Printer (ERP-400)
7-2-2 Parts List
SAM4S ER-5100 SERIES
7-7
7 Exploded Views and Parts List
7-2 Printer (ERP-400)
7-2-2 Parts List
7-8
SAM4S ER-5100 SERIES
7 Exploded Views and Parts List
7-2 Printer (ERP-400)
7-2-2 Parts List
SAM4S ER-5100 SERIES
7-9
7 Exploded Views and Parts List
7-4 Key Board
7-4-1 Key Board (60Key)
7-4-1-(a) Exploded View
Figure7-6 Key Board (60 Key)
7-10
SAM4S ER-5100 SERIES
7 Exploded Views and Parts List
7-4 Key Board
7-4-1-(b) Parts List
No.
F
Code No.
JK59-30006A
Description
UNIT-KBD ASS'Y
Specification
MEMBRANE,60 KEY:ER-5215
Q`ty
1
Remark
Serviceable
Y
F-1
JK72-40230A
PMO-KBD HOUSING
HIPS(VO),60 KEY
1
F-2
JK81-10286D
AS-KEY CAP S(1*1)
PC,S-Z0513-71#01
1
Y
F-3
JK59-30006A
LABEL KEY TOP
-
1
N
F-4
JK81-10286C
AS-KEY TOP S(1*2)
ABS,302KAS-014-01
1
Y
F-5
JK81-10286B
AS-CONTACT SPRING
SUS304,601KAS-001-01
1
Y
Y
F-6
JK81-10286A
AS-RETURN SPRING(1*1)
SWP-A,601KAS-005-01
1
Y
F-7
JK72-40310A
PMO-COVER BLANK(1*1)
HIPS(VO)
1
Y
F-8
JK72-40311A
PMO-COVER BLANK(1*5)
HIPS(VO)
1
Y
F-9
JK81-10286E
AS-KEY CAP L(1*2)
PC,S-Z0513-75#01
1
Y
F-10
JK72-40327A
AS-KEY TOP L(1*1)
ABS,302KAS-032-00
1
Y
F-11
JK61-70301A
AS-RETURN SPRING(1*2)
SWP-A,601KAS-016-01
1
Y
F-12
JK72-40324A
PMO-HOLDER HOOK(A)
POM,541KAS-001-01
1
Y
F-13
JK70-10382A
IPR-SPACER KEYBOARD
SUS304,321KAS-019-90
1
Y
F-14
JK72-40325A
PMO-HOLDER HOOK(B)
POM,541KAS-002-01
1
Y
F-15
JK72-40309A
PMO-FRAME KEYBOARD
POM,60 KEY,101KAS-054-01R
1
Y
F-16
6002-000175
SCREW-TAPPING
PWH,+,2,M3,L8,ZPC(YEL)
8
Y
F-17
JK41-10100F
FPC(60 KEY)
402KAS-101~102-01R
1
Y
F-18
JK70-10379A
IPR-BASE PLATE(60 KEY)
SECC T0.8,501KAS-032-01R
1
Y
F-19
6002-000147
SCREW-TAPPING
PH,+,2,M3,L10,ZPC(YEL)
2
Y
JK72-40250A
PMO-KEY CAP/1
ABS,302KAS-017-21
1
Y
JK72-40251A
PMO-KEY CAP/2
ABS,302KAS-017-22
1
Y
JK72-40252A
PMO-KEY CAP/3
ABS,302KAS-017-23
1
Y
JK72-40253A
PMO-KEY CAP/4
ABS,302KAS-017-24
1
Y
JK72-40261A
PMO-KEY CAP/5
ABS,302KAS-018-05
1
Y
JK72-40254A
PMO-KEY CAP/6
ABS,302KAS-017-26
1
Y
JK72-40255A
PMO-KEY CAP/7
ABS,302KAS-017-27
1
Y
JK72-40256A
PMO-KEY CAP/8
ABS,302KAS-017-28
1
Y
JK72-40257A
PMO-KEY CAP/9
ABS,302KAS-017-29
1
Y
JK72-40262A
PMO-KEY CAP/0
ABS,302KAS-017-30
1
Y
JK72-40258A
PMO-KEY CAP/00
ABS,302KAS-017-31
1
Y
JK72-40259A
PMO-KEY CAP/.
ABS,302KAS-017-32
1
Y
F-20
SAM4S ER-5100 SERIES
7-11
7 Exploded Views and Parts List
7-4 Key Board
7-4-2 Key Board (90Key)
7-4-2-(a) Exploded View
Figure7-7 Key Board (90 Key)
7-12
SAM4S ER-5100 SERIES
7 Exploded Views and Parts List
7-4 Key Board
7-4-2-(b) Parts List
No.
F
Parts No.
JK59-30004A
UNIT-KBD ASS'Y: MEMBRANE,90 KEY;ER-5240/USA
F-1
JK72-40231A
PMO-KBD HOUSING: HIPS(VO),90 KEY
1
Y
F-2
JK81-10286D
AS-KEY CAP S(1*1): PC,S-Z0513-71#01
1
Y
F-3
JK59-30004A
LABEL KEY TOP: ER-5240/USA
1
N
F-4
JK81-10286C
AS-KEY TOP S(1*1): ABS,302KAS-014-01
1
Y
F-5
JK81-10286B
AS-CONTACT SPRING: SUS304,601KAS-001-01
1
Y
F-6
JK81-10286A
AS-RETURN SPRING(1*1): SWP-A,601KAS-005-01
1
Y
F-7
JK72-40310A
PMO-COVER BLANK(1*1): HIPS(VO)
1
Y
F-8
JK72-40311A
PMO-COVER BLANK(1*5): HIPS(VO)
1
Y
F-9
JK81-10286E
AS-KEY CAP L(1*2): PC,S-Z0513-75#01
1
Y
F-10
JK72-40327A
AS-KEY TOP L(1*2): PC,S-Z0513-75#01
1
Y
F-11
JK61-70301A
AS-RETURN SPRING(1*2): SWP-A,601KAS-016-01
1
Y
F-12
JK72-40324A
1
Y
F-13
JK70-10382A
1
Y
F-14
JK72-40325A
1
Y
F-15
JK72-40312A
F-16
6002-000175
PMO-HOLDER HOOK(A): POM,541KAS-001-01
IPR-SPACER KEYBOARD: SUS304,321KAS-01990
PMO-HOLDER HOOK(B): POM,541KAS-002-01
PMO-FRAME KEYBOARD: POM,90 KEY,101KAS055-01R
SCREW-TAPPING: PWH,+,2,M3,L8,ZPC(YEL)
F-17
JK41-10100K
F-18
JK70-10380A
F-19
F-20
Description / Specification
Q`ty
1
Design-Location
Serviceable
Y
1
Y
12
Y
1
Y
1
Y
6002-000147
FPC(90 KEY): 402KAS-103~104-01R
IPR-BASE PLATE(90 KEY): SECC T0.8,501KAS032-01R
SCREW-TAPPING: PH,+,2,M3,L10,ZPC(YEL)
3
Y
JK72-40250A
PMO-KEY CAP/1: ABS,302KAS-017-21
1
Y
JK72-40251A
PMO-KEY CAP/2: ABS,302KAS-017-22
1
Y
JK72-40252A
PMO-KEY CAP/3: ABS,302KAS-017-23
1
Y
JK72-40253A
PMO-KEY CAP/4: ABS,302KAS-017-24
1
Y
JK72-40261A
PMO-KEY CAP/5: ABS,302KAS-018-05
1
Y
JK72-40254A
PMO-KEY CAP/6: ABS,302KAS-017-26
1
Y
JK72-40255A
PMO-KEY CAP/7: ABS,302KAS-017-27
1
Y
JK72-40256A
PMO-KEY CAP/8: ABS,302KAS-017-28
1
Y
JK72-40257A
PMO-KEY CAP/9: ABS,302KAS-017-29
1
Y
JK72-40262A
PMO-KEY CAP/0: ABS,302KAS-017-30
1
Y
JK72-40258A
PMO-KEY CAP/00: ABS,302KAS-017-31
1
Y
JK72-40259A
PMO-KEY CAP/.: ABS,302KAS-017-32
1
Y
SAM4S ER-5100 SERIES
Remark
7-13
7 Exploded Views and Parts List
7-4 Key Board
7-4-3 Key Board (160Key)
7-4-3-(a) Exploded View
Figure7-8 Key Board (160 Key)
7-4-3-(b) Parts List
No.
F
Parts No.
JK59-30016A
Description / Specification
UNIT-KEYBOARD,RUBBER-FLAT,160KEY
Q`ty
1
Design-Location
Serviceable
Y
F-1
JK73-20216A
REX-WATER-PROOF:SILICON,160KEY
1
Y
F-2
JK68-40012A
LABEL(P)-KBD SHEET: ER-5100, PC T0.125
1
F-3
JK81-20018A
PMO-HOUSING:HIPS(V0) IV,RUBBER,160KEY
1
Y
Y
F-4
JK81-20019A
RUBBER-KEY,SILICON,160KEY
1
Y
F-5
JK81-20020A
ASSY-FPC,RUBBER,160KEY
1
Y
F-6
JK81-20005A
SCREW-TAP,M2.6*6,
19
Y
7-14
Remark
SAM4S ER-5100 SERIES
7 Exploded Views and Parts List
7-5 Drawer
7-5-1 Exploded View
a5
a3
a9
a4
a2
a1
a10
c3
a6
a. ASS'Y
BILL-COIN
(4B8C)
c1
a7
c. ASS'Y
HOUSING
a8
c2
d6
d7
d11
d8
d10
d3
b7
b5
b8
b4
d5
d1
b9
d4
b10
b. ASS'Y
TRAY-TILL
d. ASS'Y
LOCK
d9
d2
b6
e3
b2
e4
e6
b3
e2
b1
e7
e. ASS'Y
BOTTOM
e5
e1
e8
b12
b11
Figure7-9 Drawer (4B/8C)
a3
a4
a2
a5
c3
a1
a6
c1
a. ASS'Y
BILL-COIN
(5B5C)
c. ASS'Y
HOUSING
a7
a8
c2
d6
d7
d11
d8
d10
d3
d9
d2
b7
b5
b8
b4
d. ASS'Y
LOCK
d5
d1
b9
d4
b10
b6
e3
b. ASS'Y
TRAY-TILL
b2
e4
e6
b3
e2
e7
b1
e. ASS'Y
BOTTOM
e5
e1
e8
b12
b11
Figure7-10 Drawer (5B/5C)
a3
a1
a. ASS'Y
BILL-COIN
(7B8C)
c3
c1
a2
a4
c. ASS'Y
HOUSING
c2
d6
d7
d11
d8
a5
d10
d3
d9
d2
b7
b5
b8
b4
d. ASS'Y
LOCK
d5
d1
b9
d4
b10
b6
e3
b. ASS'Y
TRAY-TILL
b2
e4
e6
b3
b1
e2
e7
e5
e. ASS'Y
BOTTOM
e1
e8
b12
b11
Figure7-11 Drawer (7B/8C)
SAM4S ER-5100 SERIES
7-15
7 Exploded Views and Parts List
7-5 Drawer
7-5-2 Parts List
7-5-2-(a) ASS’Y BILL-COIN (4B/8C, 5B/5C)
No.
a
Code No.
JK97-20014A
Description / Specification
MEA-UNIT BILL COIN: A-TYPE, 4B8C
Q`ty
Design-Location
Serviceable
1
Y
JK97-00407A
MEA-UNIT BILL COIN: A-TYPE, 5B5C
1
Y
a-1
JK72-40267A
PMO-LEVER PRESS: A-TYPE,POM
4
Y
a-2
6107-000134
SPRING ES: SUS304
4
Y
a-3
JK70-10314A
IPR-HOLDER LEVER: A-TYPE,T1.2,ZPC
4
Y
a-4
6002-000175
SCREW-TAPPING: PWH,+2,M3,L8,ZPC(YEL)
3
Y
a-5
6002-001078
SCREW-TAPPING: PWH,+2,M3,L5
4
Y
a-6
JK70-10304A
IPR-PLATE HOLDER: A-TYPE,SBHG-1,T1.2
1
Y
a-7
JK72-40269A
PMO-PANEL PARTITION: A-TYPE,HIPS,BLK
3
Y
JK72-20088A
PMO-BILL COIN TILL: A-TYPE,4B8C,HIPS,BLK
1
Y
JK72-40268A
PMO-BILL COIN TILL: A-TYPE,5B5C,HIPS,BLK
1
Y
a-9
JK72-20090A
PMO-COIN PARTITION: A-TYPE,4B8C
6
Y
a-10
JK72-20089A
PMO-COIN TILL: A-TYPE,4B8C,-
1
Y
a-8
Remark
7-5-2-(a) ASS’Y BILL-COIN (7B/8C)
No.
Code No.
a
JK97-01103A
Description / Specification
MEA-UNIT BILL COIN: A-TYPE, 7B8C
Q`ty
Design-Location
1
Serviceable
Remark
Y
a-1
6002-000175
SCREW-TAPPING: PWH,+2,M3,L8,ZPC(YEL)
3
Y
a-2
JK70-00068A
IPR-HOLDER PLATE: A-TYPE,SBHG-1, T1.2
1
Y
a-3
JK72-00083A
PMO-BILL PARTITION: A-TYPE,HIPS,BLK
5
Y
a-4
JK72-00082A
PMO-BILL TILL: A-TYPE,HIPS,BLK
2
Y
a-5
JK72-00084A
PMO-BILL COIN TILL: A-TYPE,HIPS,BLK
1
Y
7-5-2-(b) ASS’Y TRAY-TILL
No.
Code No.
JK97-01073B
b
b-1
b-2
b-3
Description / Specification
Q`ty
Design-Location
Serviceable
1
N
1
N
JK75-10389A
MEA-UNIT TRAY TILL: A-TYPE,5B5C
MEA-UNIT TRAY TILL:
A-TYPE,4B8C,7B8C(EURO)
MEC-LOCK: DRAWER
1
Y
JK70-10014A
IPR-PLATE FRONT: A-TYPE,SBC-1,T1.0
1
Y
JK97-01073D
JK70-10014B
IPR-PLATE FRONT: A-TYPE,4B8C,7B8C
1
Y
JK75-00025A
MEA-TRAY TILL: A-TYPE,4B8C,7B8C
1
N
JK75-00025B
MEA-TRAY TILL: A-TYPE,5B5C
1
N
b-4
JK73-10203A
RPR-TENSION: DRAWER,SPONGE,BLK
2
N
b-5
JK75-10386A
MEC-ROLLER: DRAWER,DR-10-B1/ Φ19
2
Y
b-6
6031-000549
WASHER-PLAIN: IDΦ6.5,ODΦ13, T1.0
2
Y
b-7
6003-000221
SCREW-TAPTITE: PWH,+2,M4,L8,ZPC(YEL)
1
Y
b-8
JK70-10324A
IPR-SUPPORT TRAY: DRAWER,SBHG-1,T1.2
1
N
b-9
JK70-40302A
ICT,SHAFT PIN: A-TYPE
1
N
b-10
6044-000124
RING-E: IDΦ3,ODΦ7, T0.6,ZPC(BLK),STSC
1
Y
b-11
6002-001042
SCREW-TAPPING: FH,+2,M3,L6
2
Y
b-12
JK70-10323A
IPR-PLATE CLIP: DRAWER,SWP,T0.5
1
Y
7-16
Remark
SAM4S ER-5100 SERIES
7 Exploded Views and Parts List
7-5 Drawer
7-5-2 Parts List
7-5-2-(c) ASS’Y HOUSING
No.
Code No.
JK97-01074A
Description / Specification
c-2
JK75-10386A
MEA-COVER HOUSING: A-TYPE,BASIC
MEA-COVER HOUSING:
A-TYPE,NONE HOLE,OPTION
MEA-SUB HOUSING: A-TYPE,BASIC
MEA-SUB HOUSING:
A-TYPE,NONE HOLE,OPTION
MEC-ROLLER: DRAWER,DR-10-B1/ Φ19
c-3
JK73-20207A
REX-PAD DRAWER: DRAWER,NR,BLK
c
JK97-01074B
JK75-00026A
c-1
JK75-00026B
Q`ty
Design-Location
Serviceable
1
N
1
N
1
N
1
N
2
N
2
N
Remark
7-5-2-(d) ASS’Y LOCK
No.
Code No.
JK97-00985A
d
JK97-00987A
d-1
6002-000157
Description / Specification
MEA-UNIT LOCK:
A-TYPE,2-LATCH,LONG LEVER
MEA-UNIT LOCK:
A-TYPE,2-LATCH,SHORT LEVER
SCREW-TAPPING: PH,+2,M4,L14,ZPC(YEL)
Q`ty
Design-Location
1
Serviceable
1
Y
1
Y
d-2
JK73-20210A
REX-BUMPER: DRAWER,NR,BLK
1
Y
d-3
JK61-70100A
1
Y
1
N
1
N
1
Y
d-5
6107-001014
SPRING-PUSH: DRAWER,FZN
MEC-LOCK LEVER:
A-TYPE,2-LATCH,LONG LEVER
MEC-LOCK LEVER:
A-TYPE,2-LATCH,SHORT LEVER
SPRING-ES: Φ0.4,D4.8,L18
d-6
JK33-10500A
SOLENOID-DC: A-DRAWER
1
Y
d-7
6001-000131
SCREW-MACHINE: BH,+2,M3,L6,ZPC(YEL)
2
Y
d-8
6001-000525
SCREW-MACHINE: PH,+2,M3,L14,ZPC(YEL)
2
Y
d-9
3405-001013
SWITCH-MICRO: 125V,5A
1
Y
d-10
JK39-40301R
CBF-HARNESS: 2P,150MM,BRN,1007
1
Y
d-11
6002-000161
SCREW-TAPPING: PH,+2,M4,L8,ZPC(YEL)
3
Y
JK75-00027A
d-4
JK75-00027B
Remark
Y
7-5-2-(e) ASS’Y BOTTOM
No.
e
e-1
e-2
Code No.
Description / Specification
JK97-01976A
MEA-UNIT BOTTOM: A-TYPE
Q`ty
Design-Location
Serviceable
1
N
N
JK97-01076B
MEA-UNIT BOTTOM: A-TYPE,UNIVERSAL
1
JK70-10938A
IPR-PLATE BOTTOM: A-TYPE,SBHG-1,T1.0
1
N
JK73-40200A
RMO-STOPPER: DRAWER,NR,BLK
2
N
N
JK73-10902A
RMO-STOPPER: DRAWER,NR,BLK,UNIVERSAL
2
e-3
JK61-40200A
RMO-FOOT RUBBER: DRAWER,NR,GRAY,80HB
4
Y
e-4
6002-000234
SCREW-TAPPING: TH,+2,M4,L16,ZPC(YEL)
4
Y
e-5
6003-000267
SCREW-TAPTITE: PWH,+2,M3,L8,ZPC(YEL)
6
Y
e-6
6003-000267
SCREW-TAPTITE: PWH,+2,M3,L8,ZPC(YEL)
2
Y
e-7
JK70-10401A
IPR-PLATE SPRING: DRAWER,STS304,T0.3
2
Y
e-8
6003-000267
SCREW-TAPTITE: PWH,+2,M3,L8,ZPC(YEL)
4
Y
SAM4S ER-5100 SERIES
Remark
7-17
7 Exploded Views and Parts List
Memo
7-18
SAM4S ER-5100 SERIES
8 PCB Parts List
8-1 Main PCB (c.f. 10-1 Main PCB Diagram)
No
Part-No
-
JK92-01054A
-
JK92-01054B
-
JK92-01054C
-
JK92-01054D
-
JK92-01055A
-
JK92-01055B
-
JK92-01055C
-
JK92-01055D
-
JK92-01056A
-
JK92-01056B
-
JK92-01056C
-
JK92-01056D
-
JK92-01057A
-
JK92-01057B
-
JK91-01057C
-
JK91-01057C
-
JK92-01070A
-
JK92-01070B
-
JK92-01070C
-
JK92-01070D
-
JK92-01071A
-
JK92-01071B
-
JK92-01071C
-
JK91-01071D
-
JK92-01064D
-
Description / Specification
Q'TY
Design-location
Serviceable
1
BASIC
Y
1
CLERK KEY
Y
1
BASIC
Y
1
CLERK KEY
Y
1
BASIC
Y
1
CLERK KEY
Y
1
BASIC
Y
1
CLERK KEY
Y
1
BASIC
Y
1
CLERK KEY
Y
1
BASIC
Y
1
CLERK KEY
Y
1
BASIC
Y
1
CLERK KEY
Y
1
BASIC
Y
1
CLERK KEY
Y
1
BASIC
Y
1
CLERK KEY
Y
1
BASIC
Y
1
CLERK KEY
Y
1
BASIC
Y
1
CLERK KEY
Y
1
BASIC
Y
1
CLERK KEY
Y
ASS’Y PCB ER-5140FI
1
BASIC
Y
0402-000168
DIODE-RECTIFIER;1N5822,40V,3A
1
D2
Y
-
0402-000208
DIODE-RECTIFIER;EK-04,40V,1.5A
3
D13,D36,D100
Y
-
0402-000287
DIODE-BRIDGE;GBL01,100V,3A,SIP
1
BD1
Y
-
0402-000395
DIODE-ZENER;UZP6.2B,5.8-6.6Z
1
ZD3
Y
-
0502-000240
TR-POWER:KSA614-Y,PNP,25W,TO-220,TP,120
1
Q14
Y
-
0506-001019
TR-ARRAY;STA471A,NPN,4,4W,SIP
4
TA1,TA2,TA3,TA4
Y
-
0801-000522
IC-CMOS LOGIC;74HCT541,BUFFER
1
IC12 (CLERK KEY)
Y
-
0801-000485
IC-CMOS LOGIC:74HCT138,3-TO-8 DECODER
3
IC9,IC10,IC11
Y
-
0904-001230
IC-PERIPHERAL;82C55,8BIT,DIP,40P
1
IC13
Y
-
1102-000109
IC-EPROM;27C010,128Kx8BIT,DIP
1
IC5
Y
ASS;Y PCB ER-5100 (EUROPE)
ASS’Y PCB ER-5100 (USA)
ASS’Y PCB ER-5115 (EUROPE)
ASS’Y PCB ER-5115 (USA)
ASS’Y PCB ER-5140 (EUROPE)
ASS’Y PCB ER-5140 (USA)
ASS’Y PCB ER-5140F (EUROPE)
ASS’Y PCB ER-5140F (USA)
ASS’Y PCB ER-5100F (EUROPE)
ASS’Y PCB ER-5100F (USA)
ASS’Y PCB ER-5115F (EUROPE)
ASS’Y PCB ER-5115F (USA)
SAM4S ER-5100SERIES
Remark
8-1
8 Electrical Parts List
No
Part-No
Description / Specification
Q'TY
-
1102-000135
IC-EPROM:27C020,256Kx8BIT,DIP,32P,600MIL
1
IC5 (ER-5140FI)
Y
-
1106-000389
IC-SRAM:681000,128Kx8BIT,DIP,32P,600MIL
1
IC6
Y
-
1203-000442
IC-POSI.FIXED REG.;7812,TO-220
1
Q13
Y
-
2011-000290
R-NETWORK;1Kohm,5%,1/8W,A,SIP
1
RA1
Y
-
2011-000539
R-NETWORK;4.7Kohm,5%,1/8W,A,SIP
1
RA2 (CLERK KEY)
Y
-
2011-000539
R-NETWORK;4.7Kohm,5%,1/8W,A,SIP
1
RA3
Y
-
2201-000119
C-CERAMIC,DISC:100nF,+80-20%,50V,Y5V,TP
3
104
Y
-
2401-002144
C-AL:47uF,20%,16V,GP,TP,5x11,5
2
R34 BOTH, R37 BOTH
Y
-
2401-000230
C-AL:100uF,20%,100V,GP,TP,12.5x20mm
1
CE3
Y
-
2401-001442
C-AL;470uF,20%,63V,GP,TP,5x12.5
1
CE2
Y
-
2401-001312
C-AL;4700uF,20%,50V,GP,BK,22x4
1
CE1
Y
-
2503-001030
C-NETWORK:100PFX8,20%,50V,X7R
1
CA3
Y
-
2801-003376
CRYSTAL-UNIT;0.032768MHz,20ppm
1
X2
Y
-
3002-001027
BUZZER-PIEZO:85dB,1.5V,24mA,2.048KHz
1
BUZZER
Y
-
3601-000261
FUSE-CARTRIDGE:250V,3.15A,TIME-LAG
1
FUSE
Y
-
3701-000232
CONNECTOR-DSUB;9P,2R,FEMALE,ANGLE
1
CN18
Y
-
3704-000255
SOCKET-IC:32P,DIP,SN,2.54mm
1
IC5 SOCKET
Y
-
3708-000215
CONNECTOR-FPC/FFC/PIC:20P,2.54mm
1
CN15 (ER-5100)
Y
-
3708-000147
CONNECTOR-FPC/FFC/PIC:12P,2.54mm
1
CN15 (ER-5140)
Y
-
3708-000327
CONNECTOR-FPC/FFC/PIC:8P,2.54mm
1
CN15 (ER-5115)
Y
-
3708-000327
CONNECTOR-FPC/FFC/PIC:8P,2.54mm
1
CN16
Y
-
3710-000111
CONNECTOR-SHUNT;2P,1R,2.54mm
1
CN21
Y
-
3711-000041
CONNECTOR-HEADER:BOX,8P,1R,2.5,RED
1
CN6
Y
-
3711-000183
CONNECTOR-HEADER;1WALL,2P,1R,3.96mm
2
CN4,CN5
Y
-
3711-000242
CONNECTOR-HEADER;1WALL,4P,1R,3.96mm
1
CN1
Y
-
3711-003969
CONNECTOR-HEADER;BOX,2P,1R,2.5,WHT
2
CN11,CN12 (P/SENSOR)
Y
-
3711-003969
CONNECTOR-HEADER;BOX,2P,1R,2.5,WHT
2
CN2,CN3
Y
-
3711-001011
CONNECTOR-HEADER;BOX,5P,1R,2.5,WHT
1
CN14 (CLERK KEY)
Y
-
3711-001133
CONNECTOR-HEADER;BOX,8P,1R,2.5,WHT
1
CN17
Y
-
3711-001475
CONNECTOR-NOWALL,3P,1R,2.54mm
2
CN21,CN25
Y
-
3711-001962
CONNECTOR-NOWALL,30P,2R
1
CN13 (FISCAL)
Y
-
4302-000126
BATTERY-NICD(2ND):3.6V(1.2Vx3),60Mah
1
BATTERY
Y
-
JC68-10564A
LABEL(P)-PROTECTOR;SLB-3108H,ART
1
EPROM LABEL
Y
-
JK13-10050A
IC ASIC:ER-5200,SCR60K,QFP,100P
1
IC4
Y
-
JK27-60100D
COIL FILTER-;ER-350,140 UH
1
COIL
Y
-
JK39-40512A
CBF HARNESS:ER-4615F,-,UL1007,70mm,GRN
1
A TO A (TOP SIDE)
Y
-
JK39-40541A
CBF HARNESS-MAIN:ER-4615,1R,UL1015,220m
2
GND1,GND2
Y
-
JK39-40306D
CBF-HARNESS;ER-4615FP,UL1007
1
CN7/CN8
Y
8-2
Design-location
Serviceable
Remark
SAM4S ER-5100 SERIES
8 Electrical Parts List
No
Part-No
Description / Specification
-
JK39-40306C
CBF-HARNESS;ER-4615FP,UL1007
1
-
JK39-40550A
CBF-HARNESS-JUMPER;ER-350F,WIR
1
-
JK68-10232A
LABEL(P)-BATTERY;ER-4915(CRS)
1
BATTERY WARNING
Y
-
JK73-10207A
RPR-PAD;ER-220N,SPONGE,BLK
1
CLOCK B’D
Y
-
0502-000234
TR-POWER;KSA1010Y,PNP,40W,TO-220
1
Q3
Y
-
0502-000395
TR-POWER:KSD73-Y,NPN,30W,TO-220,120-240
1
Q2
Y
-
6002-000175
SCREW-TAPPING;PWH,+,2,M3,L8,ZP
2
Q2,Q3
Y
-
6203-000107
HEAT SINK;NONE,T2,W17,L22,H45
2
Q2,Q3
Y
SAM4S ER-5100SERIES
Q'TY
Design-location
CN9
SOLDER SIDE
(IC5 30P~IC4 88P)
Serviceable
Remark
Y
Y
8-3
8 Electrical Parts List
8-2 Main Auto
No
Part-No
-
JK94-01065A
-
8-4
Description / Specification
Q'TY
Design-location
Serviceable
PBA MAN-AUTO
1
0401-00005
DIODE-SWITCHING;1N4148,75V,300
22
D1,D1~35,D101
Y
-
0402-000129
DIODE-RECTIFIER;1N4003,200V,1A
7
D3,D5~9,D14
Y
-
0402-000208
DIODE-RECTIFIFR;EK-04,40V,1.5A
6
D10~13,D36,D100
Y
-
0403-000343
DIODE-ZENER;UZ3,9B3.7-4.1V,50
1
ZD2
Y
-
0403-000537
DIODE-ZENER;1N4749A,5%,1W,DO-4
1
ZD1
Y
-
0501-000399
TR-SMAII SIGNAI;KSC945-G,NPN,2
11
Q1/4~6/9~12/15~17
Y
-
0801-000967
IC-CMOS I OGIC; 74HCT138,3-TO-8
1
IC9
Y
-
0909-00111
IC-REAL TIMF CLOCK;5C15,4BIT,D
1
IC8
Y
-
1006-000137
IC-DRIVER/RECEIVER;232,DIP,16P
1
IC14
Y
-
1202-000103
IC-VOLTAGE COMP.;232,DIP,16P
1
IC2
Y
-
1203-000391
IC-DC/DC CONVERTER;34063,DIP,8
1
IC1
Y
-
1206-000139
IC-TIMER;NE555CN,DIP,8P,250MIL
1
IC3
Y
-
2001-000027
R-CARBON;100ohm,5%,1/4W,AA,TP,
3
R58~60
Y
-
2001-000034
R-CARBON;220ohm,5%,1/4W,AA,TP,
4
R48,R51,R53,R76
Y
-
2001-000036
R-CARBON;330ohm,5%,1/4W,AA,TP,
1
R82
Y
-
2001-000042
-
2001-000045
R-CARBON;1.8ohm,5%,1/4W,AA,TP,
1
R79
Y
-
2001-000047
R-CARBON;2.2ohm,5%,1/4W,AA,TP,
4
R35/R36R61/87
Y
-
2001-000055
R-CARBON;4.7Kohm,5%,1/4W,AA,TP,
9
R44~46/54/62~65/68
Y
-
2001-000055
R-CARBON;4.7Kohm,5%,1/4W,AA,TP,
6
R9/16~17/22/34/37
Y
-
2001-000055
R-CARBON;4.7Kohm,5%,1/4W,AA,TP,
8
R1/24/31/93~97
Y
-
2001-000055
R-CARBON;4.7Kohm,5%,1/4W,AA,TP,
7
R70/89~92/98/99
Y
-
2001-000055
R-CARBON;4.7Kohm,5%,1/4W,AA,TP,
1
R73 (ER-5140 FI)
Y
-
2001-000060
R-CARBON;6.8Kohm,5%,1/4W,AA,TP,
2
R21/77
Y
-
2001-000060
R-CARBON;6.8Kohm,5%,1/4W,AA,TP,
1
R73 (ER-5140 FI)
Y
-
2001-000065
R-CARBON;10Kohm,5%,1/4W,AA,TP,
9
R8/25~28/47/49/56/30
Y
-
2001-000065
R-CARBON;10Kohm,5%,1/4W,AA,TP,
8
R69/71~75/86/88
Y
-
2001-000073
R-CARBON;33Kohm,5%,1/4W,AA,TP,
1
R18
Y
-
2001-000076
R-CARBON;47Kohm,5%,1/4W,AA,TP,
3
R5/R50/52
Y
-
2001-000081
R-CARBON;68Kohm,5%,1/4W,AA,TP,
3
R10/23/100
Y
-
2001-000113
R-CARBON;18Kohm,5%,1/4W,AA,TP,
1
R19
Y
-
2001-000855
R-CARBON;560ohm,5%,1/4W,AA,TP,
3
R3/55/57
Y
-
2001-000876
R-CARBON;6.2Kohm,5%,1/4W,AA,TP,
2
R14/R15
Y
-
2001-000915
R-CARBON;680ohm,5%,1/4W,AA,TP,
1
R12
Y
-
2004-000284
R-CARBON;100ohm,5%,1/4W,AA,TP,
1
R7
Y
R-CARBON;1Kohm,5%,1/4W,AA,TP,
13
Remark
N
R4/11/13/20/38
Y
~43/67/80/81
SAM4S ER-5100 SERIES
8 Electrical Parts List
-
2004-000825
R-METAL;12Kohm,1%,1/4W,AA,TP,2
2
R6/R8
Y
-
2005-000210
R-METAL;36Kohm,1%,1/4W,AA,TP,2
1
R2
Y
-
2201-000013
C-CERAMIC,DISC;470pF,10%,50V
7
CC3/11/15/16/52/62/63
Y
-
2201-000021
-
2201-000021
C-CERAMIC,DISC;100nF,+80-20%,5
5
CC66/67/68/69/64
Y
-
2201-000021
C-CERAMIC,DISC;100nF,+80-20%,5
5
CC37,38,40,12,50
Y
-
2201-000021
C-CERAMIC,DISC;100nF,+80-20%,5
5
CC25,26,28~30
Y
-
2201-000021
C-CERAMIC,DISC;100nF,+80-20%,5
5
CC43~47
Y
-
2201-000138
C-CERAMIC,DISC;100pF,10%,50V,Y
10
CC51,53~61
Y
-
2201-000138
-
2201-000163
C-CERAMIC,DISC;10nF,79.8,50V,Y
1
CC21
Y
-
2201-000232
C-CERAMIC,DISC;150pF,10%,50V,Y
1
CC1
Y
-
2201-000464
C-CERAMIC,DISC;30pF,10%,50V,Y
2
CC35,36
Y
-
2201-000776
C-CERAMIC,DISC;47nF,+80-20%,50
2
CC23/24
Y
-
2201-000579
C-CERAMIC,MLC-AXIAL;100nF,+80-
2
CC17,CC18
Y
-
2301-000010
C-FILM,PEF;100nF,5%,100V,TP,11
4
CM1~4
Y
-
2401-000023
C-AL;1uF,20%,16V,GP,TP,6.3x1
1
CE10
Y
-
2401-000025
C-AL;100uF,20%,16V,GP,TP,6.3x1
3
CE11/17/19
Y
-
2401-000025
C-AL;100uF,20%,16V,GP,TP,6.3x1
1
CE9
Y
-
2401-000783
C-AL;220uF,20%,16V,GP,TP,6.3x1
1
CE9 (ER-5140 FI)
Y
-
2401-000025
C-AL;100uF,20%,16V,GP,TP,6.3x1
3
CE20/21/23
Y
-
2401-000027
C-AL;4.7uF,20%,16V,GP,TP,6.3x1
3
CE7/13/14
Y
-
2401-000028
C-AL;10uF,20%,16V,GP,TP,6.3x1
3
CE12/15/16
Y
-
2401-000966
C-AL;22uF,20%,16V,GP,TP,6.3x1
2
CE6/22
Y
-
2401-001363
C-AL;470uF,20%,16V,GP,TP,6.3x1
2
CB5/8
Y
-
3901-000183
FILTER-EMI ON BOARD;50V,1A,-,1
3
CB1~3
Y
-
3301-000299
CORE-FERRITE BEAD;AA,3.6x5.0mm
6
FB36/37/39/40/43/44
Y
-
3301-000299
CORE-FERRITE BEAD;AA,3.6x5.0mm
15
FB9/21~34
Y
-
3301-000299
CORE-FERRITE BEAD;AA,3.6x5.0mm
3
FB18/20/46
Y
-
3301-000344
CORE-FERRITE BEAD;AA,3.6x5.0mm
4
FB35,41,42,45
Y
-
3301-000344
CORE-FERRITE BEAD;AA,3.6x5.0mm
5
FB1/2/4/7/8
Y
-
3301-000344
CORE-FERRITE BEAD;AA,3.6x5.0mm
8
FB10-17
Y
-
3602-000001
FUSE-CLIP;-,-,30mohm
2
Fuse
Y
-
BH39-40305U
CBF-HARNESS;,52MM,,,AWG22(0.6P
72
J43~107/111~116/121
Y
-
BH39-40305U
CBF-HARNESS;,52MM,,,AWG22(0.6P
17
J23~27/29/30/32~41
Y
-
BH39-40305U
CBF-HARNESS;,52MM,,,AWG22(0.6P
18
J1~4/5~7/10~15/17~21
Y
-
JK41-10528A
PCB-MAIN;ER-5100(EUROPE),FR-1,
1
MAIN PCB
Y
C-CERAMIC,DISC;100nF,+80-20%,5
C-CERAMIC,DISC;100pF,10%,50V,Y
SAM4S ER-5100SERIES
10
10
CC2,4.6.8~10,19
~20,22,100
CC27,31, CC71~75
~34,41,42,48,70,77
Y
Y
8-5
8 Electrical Parts List
8-3 Clock PCB (c.f. 10-2 Clock PCB Diagram)
No
Part-No
Description / Specification
Q'TY
Design-location
Serviceable
-
JK92-01062A
CLOCK BOARD:ER-5100,WORLD
1
-
2007-000308
R-CHIP:10OHM,5%,1/10W,DA,TP,2012
1
CR5
Y
-
2001-000477
R-CHIP:1MOHM,5%,1/10W,DA,TP,2012
1
CR1
Y
-
2007-000493
R-CHIP:2.2KOHM,5%,1/10W,DA,TP,2012
1
CR2
Y
-
2007-000941
R-CHIP:47KOHM,5%,1/10W,DA,TP,2012
2
CR3,CR4
Y
-
2007-001155
R-CHIP:750OHM,5%,1/10W,DA,TP,2012
1
CR6
Y
-
2203-000192
C-CERAMIC,CHIP:100nF,+80-20%,50V
1
CCC5
Y
-
2203-000634
C-CERAMIC,CHIP:0.022nF,5%,50V
3
CCC1,CCC2,CCC4
Y
-
2203-000938
C-CERAMIC,CHIP:0.47nF,5%,50V
1
CCC3
Y
-
3301-000325
CORE-FERRITE BEAD:AB,3.2x2.5x1.3mm
2
CBD1,CBD2
Y
-
4701-001020
IC-FREQ-ATTENUATOR:5-80MHz,15dB
1
CU1
Y
-
2401-000913
C-AL:22uF,20%,16V,GP,TP,5x11,5
1
CCE1
Y
-
2802-001030
RESONATOR-CERAMIC:22.11MHz,0.5%
1
CX1
Y
-
JK41-10519A
PCB-CLOCK;ER-5100,,ER-4
1
Remark
Y
Y
8-4 Front Display PCB (c.f. 10-3 Front Display PCB diagram)
No
Part-No
Description / Specification
Q'TY
-
JK92-01230A
PBA SUB-DISPLAY:ER-5100/5200,STD
1
ASSY
Y
-
3711-001133
CONNECTOR-HEADER:BOX,8P,1R,2.5mm,ST
1
CN1
Y
-
3711-002002
CONNECTOR-HEADER:-,22P,2R,2mm,ST
1
CN2
Y
-
JK07-00005A
DISPLAY VFD-DC10G:FUTABA,10-LT-50GK
1
FUTABA VFD/10 DIGIT
Y
-
JK39-00034A
CONNECT WIRE-350 DISPLAY:ER-350,FLAT
1
DISPLAY TO MAIN
Y
-
JK73-10207A
RPR-PAD:ER-220N,SPONGE,-,BLK,-
2
PAD(T5.0)
Y
-
1003-001381
IC-VFD:HV5812P,DIP,28P,540MIL,-,-,ST,PLA
1
U1
Y
-
JK41-10548A
PCB-DISPLAY:ER-5100/5200,FR-1,1L,T1.6
1
FUTABA VFD/10 DIGIT
Y
-
0402-000129
DIODE-RECTIFIER:1N4003,200V,1A,DO-41,TP
1
D1
Y
-
0402-000208
DIODE-RECTIFIER:EK-04,40V,1.5A,DO-41
1
D2
Y
JP1,JP2,JP3,JP4,JP5
Y
-
JC39-40511A
CBF HARNESS:ML-80,JUMPER,AWG22,52mm
18
-
2202-000632
C-CERAMIC,MLC-AXIAL:100nF,20%,50V,Z5U
2
Design-location
Serviceable
Remark
JP6,JP7,JP8,JP9,JP10
JP11,JP12,JP13,JP14
JP15,JP16, JP17,JP18
8-6
C1,C2
Y
SAM4S ER-5100 SERIES
8 Electrical Parts List
8-5 Rear Display PCB (c.f. 10-4 Rear Display PCB Diagram)
No
Part-No
Serviceable
Remark
-
JK92-01231A
PBA SUB-TURRET:ER-5100/5200,STD
Description / Specification
Q'TY
1
REAR DISPLAY ASSY
Design-location
Y
-
-
JK39-40002A
CBF HARNESS:ER-220N,-,UL1061,400MM,BLK
1
DISPLAY TO MAIN
Y
-
-
JK07-00005A
DISPLAY VFD-DC10G:FUTABA,10-LT-50GK
1
FUTABA VFD/10 DIGIT
Y
-
-
3711-002812
CONNECTOR-HEADER:BOX,11P,1R,2mm,ST
2
CN1,CN2
Y
-
-
JK73-10207A
RPR-PAD:ER-220N,SPONGE,-,BLK
2
PAD
Y
-
-
JC39-40511A
CBF HARNESS:ML-80,JUMPER,AWG22,52mm
6
JP1~JP6
Y
-
-
JK41-10548B
PCB-TURRET:ER-5100/5200,FR-1,1L,T1.6
1
FUTABA VFD/10 DIGIT
Y
-
Serviceable
Remark
8-6 Fiscal PCB (c.f. 10-5 Fiscal PCB Diagram)
8-6-1 EPROM (27C010)
No
Part-No
Description / Specification
Q'TY
Design-location
-
JK92-00130G
PBA SUB-FISCAL BOARD
1
-
1102-000109
IC-EPROM:27C010,128Kx8BIT,DIP,32P
1
U1
Y
-
2011-000539
R-CETWORK, 4.7KOHM. 5%, 1/8W, SIP, 9P
1
RA1
Y
-
JK39-40305B
CBF-HARNESS ;UL1007, 120, WHT / BLU
1
FISCAL HARNESS
Y
-
0402-000208
DIODE-RECTIFIER, EK-04, 40V, 1.5A
2
D1,D2
Y
-
0403-000141
DIODE-ZENOR, 1N4735A, 6.2V, 5%, 1W
1
D3
Y
-
0501-000399
TR-SMALL SIGNAL, KSC945-G, NPN
1
Q1
Y
-
2001-000044
R-CARBON, 1.2KOHM, 5%, 1/4W
1
R4
Y
-
2001-000055
R-CARBON, 4.7KOHM, 5%, 1/4W
2
R1,R3
Y
-
2001-000855
R-CARBON, 560OHM, 5%, 1/4W
1
R2
Y
-
2202-000630
C-CERAMIC,MLC-AXIAL:100nF,10%,50V
1
C1
Y
-
JK41-10531A
PCB-FISCAL, FR-4, 2L, T1.6
1
Y
Y
8-6-2 EPROM (27C512)
No
Part-No
Description / Specification
-
JK92-00131A
PBA SUB-FISCAL BOARD
1
-
1102-000173
IC-EPROM ;27C512, 64K*8BIT, DIP, 28P
1
U1
Y
-
2011-000539
R-NETWORK, 4.7Kohm, 5%, 1/8W, SIP, 9P
1
RA1
Y
-
2202-000630
C-CERAMIC,MLC-AXIAL:100nF,10%,50V
1
C1
Y
-
JK39-40305B
CBF-HARNESS ; UL1007, 120, WHT / BLU
1
FISCAL HARNESS
Y
-
JK41-10531A
PCB-FISCAL: FR-4, 2L, T1.6
1
SAM4S ER-5100SERIES
Q'TY
Design-location
Serviceable
Remark
Y
Y
8-7
8 Electrical Parts List
8-7 Clock PCB (c.f. 10-2 Clock PCB Diagram)
No
Part-No
-
8-8
Description / Specification
Q'TY
PCB-OPTION,E-5100,FR-4,T1.6
1
Design-location
Serviceable
Remark
Y
-
0501-000399
TR-SMALL SIGNAL;KSC945,NPN
2
IQ1.2
Y
-
0904-000519
IC-PERIPHERAL,82C452A,8BIT
1
IC15
Y
-
2804-000325
OSC-CLOCK,8MHz,100PPM
1
IX1
Y
-
1006-000137
IC-DRIVER/RECEIVER,232,DIP,16P
2
IX14,16
Y
-
3701-000232
CONNECTOR-DSUB,9P,2R,FEMAL
2
XN18,20
Y
-
3301-000344
CORE-FERRITE BEAD;AA
8
IFB1-8
Y
-
2201-000021
C-CERAMIC DISC;100nF
7
ICC3,4,7,8,9,10,11
Y
-
2201-000013
C-CERAMIC DISC;470pF
4
ICC1,2,5,6
Y
-
2201-000326
C-CERAMIC DISC;2.2Nf
2
ICC12,13
Y
-
2001-000065
R-CARBON;10Kohm,1/4W,AA
3
IR1,3,4
Y
-
2001-000042
R-CARBON;1Kohm,1/4W,AA
1
IR2
Y
-
2401-000028
C-AL;10uF,20%,5V
6
ICE1,4,5,6,9,10
Y
-
2401-000027
C-AL;4.7uF,20%,5V
4
ICE2,3,7,8
Y
-
2401-000025
C-AL;100uF,20%,5V
1
ICE11
Y
-
JK39-40305X
CBF-HARNESS;150MM,22P
1
CN22
Y
-
JK39-40024A
CBF-HARNESS;350MM/GYN/YE
1
CN20 SIDE
Y
-
JK39-40305G
CBF-HARNESS;250MM/GYN/YE
1
CN18 SIDE
Y
-
JK39-40523A
CBF-HARNESS;SRP-250,BLU/BLU
1
CN23
Y
SAM4S ER-5100 SERIES
9 Block Diagram
9-1 Main
POWER
RESET
1Mbit
1Mbit
SRAM
SRAM
PAPER END
27010/
SENSOR
27C020
(Program)
CPU
ASIC
SCR 60K
R/J PRINTER
ERP-400
NTERFACE
DRIVER
MAX 232
SERIAL1
Option Board I
EPROM
NTERFACE
27C010
DRIVER
(Fiscal)
82C452 / MAX 232
SERIAL 2
Option Board II
EPROM
27C010
(Fiscal)
DISPLAY/
BUZZER
POWER
+5V
+24V
DRAWER
TURRET
MODE
CLERK
KEY
KEY
KEY BOARD
+28V
+30V
This box means Optional Part
SAM4S ER-5100 SERIES
9-1
9 Block Diagram
9-2 front/Rear display Driver
IC4
SERIAL DATA,
SCR60K
CLOCK, LATCH,
STROBE SIGNAL
+5V, +33V, GND
10 DIGITS (Display)
DRIVER
SN75518
Main PCB
10 DIGITS (Turret)
Display / Turret PCB
Clock
Data
1st Data Byte (1byte)
9th Data Byte (1byte)
1st Data Byte (1byte)
Strobe Latch
(Display wave form Diagram)
9-2
SAM4S ER-5100 SERIES
9 Block Diagram
9-3 Serial Communications
IC14
Modular
MAX
Jack
232
Serial Comm.
D-SUB 9
IC4
SCR
IC14
60K
MAX
232
82C452
9-4 IRC Communications (Optional Board II)
DATA
IC4
ADD
TxD
IRC+
Controller
IC 14
Transceiver
Modular
IC 15
MAX232
IC 4
Comm.
82C452
75176
RxD
IRC-
SCR60K
SRAM.
SAM4S ER-5100SERIES
9-3
9 Block Diagram
9-5 Printer driver
Note:
When Head driving voltage is High, Head driving time becomes Short.
When Head driving voltage 기 low, Head driving time becomes Long.
ERP-400
9-PIN DOT MATRIX R/J PRINTER
PART A
RECEIVER
PART B
DRIVER
PART C
CONTROL
TIMING PULSE SENSING,
MOTOR, STAMP, AUTO-
HEAD SOLENOID DRIVING
GUARANTEE PAPER
CUTTER,
TIME CONTROLLING
SENSING,
RECCEIPT/JOURNAL
HEAD LOCATION
PAPER FEEDING, HEAD
SENSING
SOLENOID DRIVING
IC4 (SCR 60K)
9-4
SAM4S ER-5100 SERIES
9 Block Diagram
9-6 keyboard
IC4 (ASIC SCR60K)
20 Lines
8 Lines
IC9
IC10
IC11
74138
74138
74138
CA2 / CA3
20 Lines
8 Lines
CN17
Diode (1n4148) x 20
Mode Key Switch
20 Lines
8 Line (D0 ~ 7)
Key Board
(160 / 90 / 60)
SAM4S ER-5100SERIES
9-5
9 Block Diagram
Memo
9-6
SAM4S ER-5100 SERIES
10 Wiring Diagrams
For Transformer
For Window / Turret
Pin
Output
Pin
Signal
Pin
Signal
Blue(3~4)
24V/2A
1
Disconn.chk
5
Ground
Red(5~6)
22V/0.15A
2
Strobe
6
Vpp
3
Clock
7
Vcc
4
Latch
8
Data in
For Modular Jack (CN19)
CN1
For Compulsory
Pin1
Pin2
CN2
IC4#75
Ground
CN3
IC4#76
Ground
CN19
Pin
Sa
Pin
Sa
1
DTR
4
N.C.
2
N.C.
5
Rxd
3
Txd
6
GN
CN7
CN2
CN18
CN3
ForERP-400 (Printer)
CN6
CN 7 : 12 Pins
CN8
CN8 : 10 Pins
CN9 : 14 Pins
CN4/5
Sa
5
GND
1
N.C.
6
N.C.
2
Rxd
7
N.C.
3
Txd
8
DTR
4
DTR
9
N.C.
For Optional Interface
(82C452)
For Drawer
Pin1
Pin2
CN4
IC4#60
Ground
CN5
Ground
IC4#59
CN9
For paper End sensor
Pin1
Pin
CN25
c.f. 12-5 for detail
CN11
For Serial Interface (CN18)
CN10 : 22Pins
CN10
For Clerk Key
CN14 : 5Pins
CN11/12
Pin2
c.f. 12-2 for detail
CN14
Ground CN9#13
For Mode Key
CN17 : 8Pins
CN312 SN9#13 Ground
For Fiscal (Optional)
CN 13 : 30 Pins
c.f. 12-3 for detail
CN17
CN13
CN15
c.f. 12-2 for detail
CN16
For Key Board
CN 15 : 20/12/8 Pins
CN 16 : 8 Pins
c.f. 12-3 for detail
The Pin #1 is the Pin at left or at top
SAM4S ER-5100 SERIES
10-1
10 Wiring Diagram
MEMO
10-2
SAM4S ER-5100 SERIES
11 ASIC SCR60K Pin Assignments
Pin No.
Name
1
RD
2
RTC
3
Description
Pin No.
Name
Description
Read
51
INT1
CN9 #3 (Timing Sihnal)
Real Time clock
52
PR1
CN8 #4 (Ayto Cutter)
RAM2
Chip Select
53
PR2
CN8 #8 (Motor)
4
RAM1
Chip select
54
PR3
CN8 #3 (Stamp)
5
P2
A16 (for 1M RAM)
55
PR4
CN8 #2 (Receipt Feed)
6
P4
RAM/CS
56
PR5
CN8 #1 (Journal Feed)
7
P3
A16 (for 1M ROM)
57
P8_1
CN13 #30 (Fiscal Reset), IC3 #4
8
A15
Address Bus
58
W1
NE555 Timer Trigger
9
A14
Address Bus
59
W3
CN5 (Drawer)
10
A12
Address Bus
60
W4
CN4 (Drawer)
11
A13
Address Bus
61
HD9
CN7 #12 (Head)
12
A7
Address Bus
62
HD8
CN7 #11
13
A8
Address Bus
63
HD7
CN7 #10
14
A9
Address Bus
64
HD6
CN7 #9
15
VDD1
+5V
65
VDD9
16
A9
Address Bus
66
RAM1_1
Open
17
GND3
0V (ground)
67
GND12
0V (Ground)
18
A5
Address Bus
68
HD5
CN7 #8
19
A11
Address Bus
69
HD4
CN7 #4
20
A4
Address Bus
70
HD3
CN7 #3
21
PSEN
ROM/CS
71
HD2
CN7 #2
22
A3
Address Bus
72
HD1
CN7 #1
23
A10
Address Bus
73
XTAL1
Crystal 22.1184 MHz
24
A2
Address Bus
74
XTAL2
Crystal 22.1184 MHz
25
ALE
Address Latch Enable
75
R6
CN2 (Compulsory)
26
A1
Address Bus
76
R7
CN3 (Compulsory)
27
D7
Data Bus
77
R8
CN21 (All Clear)
28
A0
Address Bus
78
R3
Option Board
29
D6
Data Bus
79
R5
Buzzer
30
D0
Data Bus
80
RESET
31
D5
Data Bus
81
PWRFAIL
32
D1
Data Bus
82
R4
Display Disconnection Check
33
D4
Data Bus
83
P6
Display Clock
34
D2
Data Bus
84
P7
Display Latch Enable
35
D3
Data Bus
85
P8_1
SAM4S ER-5100 SERIES
+5V
System Reset
Power fail
Display Data in
11-1
11 ASIC SCR60K Pin Assignments
Pin No.
Name
Description
Pin No.
Name
86
RAM1_2
Description
36
AUX1
CN10 #18 (Option Board 452)
67
AUX2
CN10 #4 (Option Board 452)
87
RXD
Option board (RxD)
68
R1
CN10 #19 (Option Board 452)
88
TXD
Option board (TxD)
69
R2
CN10 #3 (Option Board 452)
89
GND 14
40
GND6
0V (Ground)
90
K8
CN16 #1 (Key Scan)
41
VDD7
+5V
91
K7
CN16 #2
42
W5
CN13 #30 (Fiscal EPROM A16)
92
K6
CN16 #3
43
AUX3
PPI 8255 /CE
93
K5
CN16 #4
44
P10
CN13 #6 (Fiscal EPROM /CS)
94
K4
CN16 # 5
45
P9
CN13 #9 (Fiscal EPROM Program
95
K3
CN16 #6
RAM1 /CS
+V (Ground)
voltage, +12V)
11-2
46
PR6
CN13 #12 (Paper sensor)
96
K2
CN16 #7
47
PR7
CN9 #10 (Journal side validation)
97
K1
CN16 #8
48
PR8
CN9 #7 ( Receipt side Reset Signal)
98
P1
CN17 #8 (Mode key)
49
PR9
CN9 #5 (Journal side Reset signal)
99
W2
CN12 #19 (Clerk key)
50
PR10
CN9 #1 (Receipt side Validation)
100
WR
Write Signal
SAM4S ER-5100 SERIES
12 Schematic Diagrams
[ Schematics Sheet Content ]
1. Main PCB Schematics.
1) Power Block ------------------------------------------------------2) CPU Block -------------------------------------------------------3) Memory and Power Fail Block -------------------------------4) Interface Block----------------------------------------------------5) Key Scan and Display Block ----------------------------------6) Fiscal Block --------------------------------------------------------
12-2
12-3
12-4
12-5
12-6
12-7
2. Display PCB Schematics.
1) VFD Front Schematics ----------------------------------------2) VFD Rear Schematics ------------------------------------------
12-8
12-9
4. Fiscal PCB Schematics. -------------------------------------------
12-10
5. Clock PCB Schematics. --------------------------------------------
12-11
6. Interface PCB Schematics. ---------------------------------------
12-12
SAM4S ER-5100 SERIES
12-1
12-2
SAM4S ER-5100 SERIES
4
3
2
1
A
CC1
150pF
TRANSFORMERS
RED
BLUE
1
2
3
4
CN1:A
B
8
7
6
5
R8
10K
R7
CC9
12K
100nF
1/4W
1%
R2
0.33
1W
24V
1N4003
D3
4
FUSE
250V/T3.15A
CM1
100nF
CM2
100nF
SC
DC
SE
SENSE
TC
VCC
GND
IN
IC1
34063
4
3
2
1
CON-WALL;4P,3.96MM,1R,1W,ST
B
R6
36K
1/4W
1%
1
BD1
GBL01
R4
1K
R3
560
CE2
470uF
63V
VDISP
3
2
3
1
2
CC8
100nF
Q3
A1010
R1
4.7K
R5
47K
CE1
4700uF
50V
VPH
2
FB1
1
Q2
D73
Q1
KSC945-G
3
HS1
H45
C
COIL
140uH
D1
1N4148
ZD1
24V(1N4749)
1W
1
D2
1N5822
3
2
C
24V
CE5
470uF
16V
VCC
CC68
100nF
CE3
100uF
100V
POWER PART
TITLE : ER-5100 MAIN
D
Date
2004.03.02
File Name ER-5100 MAIN.SCH
A3
Size
Drawn by Sungho, Kim
Sheet 1 of 11
REV1.0
Rev
Shin Heung Precision Co., Ltd.
D
4
3
2
1
4
3
R93
4.7K
VCC
R96
4.7K
R94
4.7K
RTC_/CS
RAM2_/CS
RAM1_/CS
CLOCK PCB
1
2
3
VCC
SYS-CLK
/WR
SYS-CLK
KD8
KD7
KD5
KD6
KD4
KD3
KD2
KD1
IC4#87
MODE
IC4#88
1N4148
1N4148
1N4148
/RD
RAM_/CS
PSEN
P-FAIL
RESET
BUZZER
555-TRG
DA-IN
DIS_CLK
LATCH
VCC
A(0:15)
I/F PART
J24(NO POP)
D10
D11
D12
CN25:A
CON-NOWALL;3P,2.54MM,ST
CC57
100pF
A15
A13
A14
A12
A11
A10
A9
A7
A8
A6
A5
A4
A3
A1
A2
A0
CC18
100nF
CC17
100nF
CC2
100nF
NC
CC28
100nF
28
26
24
22
20
18
14
12
13
16
23
19
10
11
9
8
15
41
65
83
84
85
58
79
80
81
6
21
1
100
4
3
2
88
98
37
38
39
87
86
97
96
95
94
93
92
91
90
73
74
CC19
100nF
CE11
100uF
16V
555_RESET
4.7K
R97
W2(CLK-KEY)
ALL_CLEAR
RAM_A16
ROM_A16
DRAWER1
DRAWER2
HEAD1
HEAD2
HEAD3
HEAD4
HEAD5
HEAD6
HEAD7
HEAD8
HEAD9
JOURNAL_FEED
RECEIPT_FEED
STAMP
D0
D1
D2
D3
D4
D5
D6
D7
DISCON
RESET
COMPULSORY1
CC50
100nF
FB45
B
NOTE] IC4 #88 : FOR 2M EPROM, ROM A17(IC5 #30)
KD1
KD2
KD3
KD4
KD5
KD6
KD7
KD8
X-TAL1
X-TAL2
MODE_S/W
P6(CLOCK)
P7(LATCH)
P8(DA-IN)
W1(555_TRG)
BUZZER
RESET
P-FAIL
P4(RAMCS)
PSEN
RD
WR
RAM1
RAM2
RTC
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
IC4
IC-CPU;SCR60K,QFP100P
CC20
100nF
VCC
B
30
32
34
35
33
31
29
27
82
57
75
76
72
71
70
69
68
64
63
62
61
56
55
54
53
52
50
51
49
48
46
47
66
17
40
67
89
36
78
42
43
44
45
25
99
77
5
7
59
60
NC
D7
D6
D5
D4
D3
D1
D2
D0
CE22
22uF
50V
555-TRG
TRIGGER
DISCON
FIS_/CS
DR2
DR1
ROM_A16
RAM_A16
CLERK
ALL_CLEAR
12.5V_EN
CC48
100pF
FISCAL PART
HEAD8
HEAD9
HEAD7
HEAD6
HEAD5
HEAD4
HEAD2
HEAD3
HEAD1
RA1
1K
VCC
8
7
6
5
FB33
GND VCC
TRIG
DC
OUT
TS
RESET CTR
CA3
100pF
CN10
I/F PART
8255_/CS
IC4#78
FIS_A16
CS0
MOTOR
AUTO_CUT
STAMP
RECEIPT_FEED
1
2
3
4
TRIGGER
FB32
JOURNAL_FEED
COMPULSORY
555_RESET
D(0:7)
FB18
IC3
KA555
CC46
100nF
VCC
24V
C
STAMP
AUTO_CUT
R43
R42
R40
C
JOURNAL_FEED
RECEIPT_FEED
MOTOR
R41
R39
R38
1K
1K
1K
HEAD9
1K
1K
1K
HEAD2
HEAD4
HEAD6
HEAD8
HEAD1
HEAD3
HEAD5
HEAD7
R58
R59
R60
CC22
2
CC58
100pF
R19
100nF
1
CC59
100pF
CM4
100nF
R18
CC21
10nF
2
4
6
8
IN1
IN2
IN3
IN4
1
10
OUT1
OUT2
OUT3
OUT4
1
10
OUT1
OUT2
OUT3
OUT4
10
IN1
IN2
IN3
IN4
1
3
5
7
9
3
5
7
9
3
5
7
9
FB46
10
OUT1
OUT2
OUT3
OUT4
3
5
7
9
CN12:1
CN11:1
TA4
STA471A
1
2
1
2
1
OUT1
OUT2
OUT3
OUT4
VCC
IN1
IN2
IN3
IN4
TA3
STA471A
IN1
IN2
IN3
IN4
TA2
STA471A
100
100
100
2
4
6
8
2
4
6
8
2
4
6
8
TA1
STA471A
HEAD_OUT9
HEAD_OUT2
HEAD_OUT4
HEAD_OUT6
HEAD_OUT8
HEAD_OUT1
HEAD_OUT3
HEAD_OUT5
HEAD_OUT7
J_FEED_OUT
R_FEED_OUT
MOTOR_OUT
R47
10K
18K
CC23
47nF
R49
10K
33K
CC24
47nF
R50
47K
CM3
CC26
100nF
R52
47K
100nF
CC25
100nF
R56
10K
HEAD_OUT9
HEAD_OUT8
HEAD_OUT6
HEAD_OUT7
HEAD_OUT5
HEAD_OUT4
HEAD_OUT3
HEAD_OUT1
HEAD_OUT2
D
CN9
CN8
CN7
D
1
2
3
4
5
6
7
8
9
10
11
12
13
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
11
12
REV1.0
Rev
Drawn by Sungho, Kim
Sheet 2 of 11
CPU, PRINTER PART
TITLE : ER-5100 MAIN
Shin Heung Precision Co., Ltd.
[PRINTER PART]
Date
2004.03.02
File Name ER-5100 MAIN.SCH
A3
Size
VCC
MOTOR_OUT
J_FEED_OUT
R_FEED_OUT
24V
VPH
D7
1N4003
R51
R55
A
CC47
100nF
R53
R54
560
220
D5
4.7K
220
D6
1N4003
R57
560
1N4003
R48
220
SAM4S ER-5100 SERIES
12-3
4
3
2
1
4
3
2
1
BATTERY
3.6V
R13
1K
R14
6.2K
R15
6.2K
2
3
4
1
IC2:A
LM393
8
R16
4.7K VCC
VCC
CE6
22uF
50V
A
FB20
R17
4.7K
R76
220
X2
CC35
30pF
D(0:7)
/WR
1
3
R70
2.2K
VCC
R69
UZ3.9B
D0
D2
D1
D3
18
17
16
15
14
13
12
11
10
2
1K
R67
IC8
RF5C15
R68
2.2K
1
3
1
2
3
4
A0
5
A1
6
A2
7
A3
8
9
CE7
4.7uF
50V
2
1
3
Q5
KSC945-G
B
CC56
10nF
R20
1K
RESET
R200
6.8K
B
RAM2_/CS
RAM1_/CS
CC33
100pF
R72
2.2K
R75
10K
VBT
CC32
100pF
R71
2.2K
RTC_/CS
R73
2.2K
RAM_A16
CE19
100uF
16V
VCC
[RESET CIRCUIT]
R22
4.7K
R21
4.7K
ZD2
ZD3.9V
500mW
VCC
CC6
100nF
VCC
A(0:15)
/RD
CC51
100pF
RAM_/CS
R45
4.7K
VCC
VCC
CS
OSCOUT
CS
OSCIN CLKOUT
ALARM
A0
D3
A1
D2
A2
D1
A3
D0
RD
WR
GND
Q10
C945
CE10
4.7uF
50V
Q11
C945
CC54
100nF
P-FAIL
[Real Time Clock Circuit ]
CC36
30pF
CC37
100nF
R74
10K
2
[Power Fail Detect]
D13
EK04
VCC
CC44
100nF
VPH
32.768KHZ
12-4
SAM4S ER-5100 SEFIES
/WR
/RD
A0
A1
A2
A3
A4
A6
A5
A7
A8
A9
A10
A12
A11
A13
A14
A15
RAM1_/CS
VBT
CC31
100pF
R44
4.7K
VCC
24
29
30
22
2
31
3
28
4
25
23
26
27
5
6
7
8
9
10
11
12
CC3
470pF
OE
WE
CS2
CS1
R23
68K
R10
68K
2
NC
D7
D6
D5
D4
D3
D2
D1
D0
GND
16
32
1
21
20
19
18
17
15
14
13
VBT
D0
D1
D3
D2
D4
D5
D6
D7
2
C
RAM2_/CS
/WR
/RD
A0
A1
A2
A3
A4
A6
A5
A7
A8
A9
A10
A12
A11
A13
A14
A15
RAM_A16
24
29
30
22
2
31
3
28
4
25
23
26
27
5
6
7
8
9
10
11
12
1
3
CC52
470pF
R31
4.7K
OE
WE
CS2
CS1
GND
VCC
A16
D7
A15
D6
A14
D5
A13
D4
A12
D3
A11
D2
A10
D1
A9
D0
A8
A7
A6
A5 RAM2
A4
A3
A2
A1
A0
NC
IC7
KM681000
1
3
VCC
VCC
Q4
KSC945-G
Q17
KSC945-G
R24
4.7K
4.7K
R9
[Buzzer]
VCC
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5 RAM1
A4
A3
A2
A1
A0
7
IC2:B
LM393
R100
68K
6
5
IC6
KM681000
VCC
R12
680K
R11
1K
VCC
C
16
32
1
21
20
19
18
17
15
14
13
VBT
D0
D1
D3
D2
D4
D5
D6
D7
BUZZER
BUZZER
CC30
100nF
ROM_A16
CE9
100uF
16V
R46
4.7K
VCC
ALL_CLEAR
CC4
100nF
1
2
3
ON
OFF
CE
OE
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
IC5
27C010
GND
VPP
VCC
PGM
O7
O6
O5
O4
O3
O2
O1
O0
D0
D1
D3
D2
D4
D5
D6
D7
16
1
32
31
CE20
100uF
16V
VCC VCC
21
20
19
18
17
15
14
13
D
REV1.0
Rev
Drawn by Sungho, Kim
Sheet 3 of 11
MEMORY, P-FAIL PART
TITLE : ER-5100 MAIN
Shin Heung Precision Co., Ltd.
22
24
30
2
3
29
28
4
25
23
26
27
5
6
7
8
9
10
11
12
Date
2004.03.02
File Name ER-5100 MAIN.SCH
A3
Size
PSEN
A1
A0
A2
A3
A4
A5
A7
A6
A8
A9
A10
A11
A13
A12
A14
A15
VCC
A(0:15)
D(0:7)
CN21:A
CON-NOWALL;3P,2.54MM,ST
[All Clear Switch]
FB8
R27
10K
VCC
D
4
3
2
1
SAM4S ER-5100 SERIES
12-5
4
3
2
1
A
IC4#88
FB31
IC4#87
1
3
5
7
9
11
13
15
17
19
21
RED BLU
2
4
6
8
10
12
14
16
18
20
22
FB29
FB30
CN10:A
2
R87
2.2K
INT1
/WR
A1
D0
A0
D1
D2
2
R88
10K
B
CC60
100pF
R95
4.7K
VCC
1
3
Q15
KSC945-G
CC100
100nF
R90
4.7K
VCC
VCC
R89
4.7K
1
3
Q16
KSC945-G
VCC
[I/F RS232*2PORT]
/RD
A2
D6
D7
D5
D4
D3
CS1
INT0
RESET
R92
4.7K
IC4#78
R91
4.7K
VCC
B
CS0
VCC
CE15
10uF
50V
CE13
4.7uF
50V
R86
10K
VCC
15
11
10
12
9
6
2
16
C2+
C2-
C1+
C1-
CE16
10uF
50V
GND
T1IN T1OUT
T2IN T2OUT
R1OUT R1IN
R2OUT R2IN
V-
V+
VCC
IC14
MAX232
CE17
100uF
16V
VCC
14
7
13
8
4
5
1
3
CC67
100nF
CB2
CE14
4.7uF
50V
CB3
CE12
10uF
50V
CC66
100nF
C
CB1
C
FB41
FB42
7
8
9
10
11
12
1
2
3
4
5
6
9
6
11
1
12
2
CN19:L
CON-RJ11;12P,2MM,2R,AN
5
1
CN18:A
CON-DSUB;9P,FEMALE,AN
1
2
3
4
5
6
7
8
9
INTERFACE PART
TITLE : ER-5100 MAIN
D
Date
2004.03.02
File Name ER-5100 MAIN.SCH
A3
Size
Drawn by Sungho, Kim
Sheet 6 of 11
REV1.0
Rev
Shin Heung Precision Co., Ltd.
D
4
3
2
1
4
3
2
1
P-FAIL
/RD
CC1010K
100nF
R26
FB25
2
1
3
R25
10K
VCC
CC38
100nF
VCC
A(0:15)
CC53
100nF
VCC
A2
FB11
FB13
FB12
FB14
6
5
4
3
2
1
16
6
5
4
3
2
1
16
6
5
4
3
2
1
16
E3
E2
E1
A2
A1
A0
VCC
IC11
E3
E2
E1
A2
A1
A0
VCC
IC10
E3
E2
E1
A2
A1
A0
VCC
IC9
GND
Q7
Q6
Q5
Q4
Q3
Q2
Q1
Q0
GND
Q7
Q6
Q5
Q4
Q3
Q2
Q1
Q0
GND
Q7
Q6
Q5
Q4
Q3
Q2
Q1
Q0
14
15
16
17
18
19
20
1N4148
1N4148
1N4148
1N4148
1N4148
1N4148
1N4148
D22
D21
D20
D19
D18
D17
D16
14
13
12
11
10
9
7
11
1N4148
1N4148
1N4148
D25
D27
D26
11
10
9
8
CC11
470pF
CC15
470pF
CC16
470pF
B
8
7
6
1
Serial Data In
VCC
VDISP(+24V)
GND
Latch
Serial Clock
Blanking(Strobe)
Disconnect
/RD
CLERK
FB7
D(0:7)
CC88
100nF
R28
10K
VCC
CC55
100pF
KB8
KB6
KB7
KB5
KB4
KB3
KB1
KB1
OE1
OE2
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
1
2
1
2
CN3:1
CN2:1
CE23
100uF
16V
C
GND
A0
A1
A2
A3
A4
A5
A6
A7
VCC
FB35
CC34
100pF
IC12
74HCT541
CC12
100nF
VCC
1
19
18
17
16
15
14
13
12
11
RA3
4.7K
FB26
FB37
D7
D6
D0
D1
D5
D4
D2
D3
VCC
MODE
C
[D/R COMPULSORY]
COMPULSORY
CN15:T
CON-FPC;20P,2.54MM,ST
CN6:1
CON-BOX;8P,2.5MM,ST(YH)
8
7
6
5
4
3
2
1
1N4148
D35
7
VDISP VCC
1N4148
D34
10
9
1N4148
1N4148
D33
D32
11
12
13
14
15
8
2
9
12
1N4148
D24
12
1N4148
5
1N4148
D28
13
D31
4
10
1N4148
D29
14
7
3
1N4148
D30
15
8
13
1N4148
D23
B
15
[Key Scan]
VCC
CS_KBDMODE
A3
A4
A5
A1
CS_KBDMODE
A3
A4
A5
A0
CS_KBDMODE
A3
A5
A4
VCC
[ VFD DISPLAY ]
DISCON
DIS_CLK
LATCH
DA-IN
CC70
100pF
CE21
100uF
16V
VCC
CC40
100nF
VCC
Q6
KSC945-G
CC42
100pF
CS_KBDMODE
A
74HC138
74HC138
74HC138
12-6
SAM4S ER-5100 SERIES
DR2
DR1
10
R35
R36
FB9
RA2
4.7K
VCC
20
2
3
4
5
6
7
8
9
D36
EK04
CE8
470uF
16V
VCC
CN16:A
CON-FPC;8P,2.54MM,ST
R34
4.7K
2.2K
2.2K
1
2
3
4
5
1
2
1
2
[DRAWER]
9
9
CN4:1
CN5:1
D
REV1.0
Rev
Drawn bySungho, Kim
Sheet 4 of 11
DISPLAY, KEY SCAN PART
TITLE : ER-5100 MAIN
Shin Heung Precision Co., Ltd.
C2
47uF
16V
TA4
TA3
Date
2004.03.02
File Name ER-5100 MAIN.SCH
A3
Size
C1
R37
47uF
4.7K
16V
8
8
D8
1N4003
24V
[CLERK KEY]
D9
1N4003
[ KEY RETURN ]
[ MODE ]
CN14:A
CON-BOX;5P,2.5MM,ST
VCC
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
CN17:1
CON-BOX;8P,2.5MM,ST(YH)
D
4
3
2
1
4
3
2
1
A
555_RESET
12.5V_EN
FB22
EK-04
D100
24V
1
3
2
1.8K
/RD
/WR
R78
36K
2
D101
1N4148
R99
R80
1K
1
3
Q12
KSC945-G
8255_/CS
3
VCC
CC43
100nF
VCC
OUT
GND
R79
IN
CC71
100pF
1
CC69
Q13
100nF
MC7812
Q9
KSC945-G
2
12.5V_EN
FB36
2.2K
R61
R62
4.7K
VCC
R98
4.7K
R64
B
B
3
1
R81
1K
2
A1
A0
CC62
470pF
Q14
KSA473-Y
or KSA614-Y
CC29
100nF
4.7K
CC41
100pF
4.7K
CC27
100pF
SAM4S ER-5100 SERIES
12-7
34
33
32
31
30
29
28
27
5
36
9
8
35
6
ZD3
1N4735A
6.2V
7
26
CC63
470pF
VCC
R77
6.8K
D7
D6
D5
D4
D3
D1
D2
D0
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
4
3
2
1
40
39
38
37
CC64
100nF
R82
330
14
15
16
17
13
12
11
10
18
19
20
21
22
23
24
25
FIS_/CS
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
CC45
100nF
D15
EK-04
D14 VCC
1N4003
GND
VCC
/RD
/WR
A0
A1
RESET
/CS
D0
D1
D2
D3
D4
D5
D6
D7
PA0
R65
4.7K
VCC
PC7
PC5
PC6
PC4
PC3
PC2
PC1
PC0
PB7
PB6
PB5
PB4
PB3
PB1
PB2
PB0
PA7
PA6
PA5
PA4
PA3
PA1
PA2
PA7
PB2
PB7
PB6
PB5
PB3
PB4
PA5
PA4
PA6
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
C
TO FISCAL B'D
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
PB1
PB0
PC3
PC2
PC0
PC1
PC4
PC5
PC6
PC7
PA1
PA0
PA2
PA3
CN13:A
CON-NOWALL;30P,2.54MM,2R,ST
PC(0:7)
PB(0:7)
D(0:7)
IC13
82C55
PA(0:7)
A(0:15)
C
CC61
100pF
R63
4.7K
VCC
FIS_A16
D
REV1.0
Rev
Drawn by Sungho, Kim
Sheet 5 of 11
TITLE : ER-5100 MAIN
Date
2004.03.02
File Name ER-5100 MAIN.SCH
A3
FISCAL PART
Size
Shin Heung Precision Co., Ltd.
D
4
3
2
1
4
3
2
e P6
CN1:A
CN1:B
CN1:C
CN1:D
CN1:E
CN1:F
CN1:G
CN1:H
1
2
3
4
5
6
7
8
C2
100nF
VDISP
C1
100nF
VCC
SEN_DISPDISCON
VFD_STORBE
VFD_SCLK
VFD_LATCH
VFD_SDIN
com P9
B
VCC
VFD_STORBE
VFD_LATCH
VFD_SDIN
VFD_SCLK
P5_C
14
2
15
27
16
13
1
28
P7_D
P6_E
GND
SDOUT
SCLK
SDIN
STB/LAT
BLNK/nSTB
VBB
VDD
O1
O2
O3
O4
O5
O6
O7
O8
O9
O10
O11
O12
O13
O14
O15
O16
O17
O18
O19
O20
26
25
24
23
22
21
20
19
18
17
12
11
10
9
8
7
6
5
4
3
P4_G
P2_B
P1_A
P3_F
F2
F2
G10
P10_H
P1_A
P2_B
D
1
3
5
7
9
11
13
15
17
19
21
BLK BLUE
2
4
6
8
10
12
14
16
18
20
22
G3
G4
G5
G6
G7
G8
G9
G10
P4_G
P3_F
VCC CN2:A
CON-BOX;22P,2MM,2R,ST
VFD FRONT PART
TITLE : ER-5200 / 5240 DISPLAY
V1.0
Rev
D
Date
Drawn by Hyun-Oh,Yun
2002.10.28
1 of 1
File Name ER5200FRONTVFD.SCH Sheet
A3
Size
Shin Heung Precision Co., Ltd.
Note] The connection of rear display pcb is same as old version(ER350/5100/5200/6500)
REAR VFD I/F CONN
G2
SEN_DISPDISCON
G1
G1
P7_D
G2
P5_C
P8_DP
G3
P7_D
P5_C
P1_A
P6_E
VF1
G4
D2
EK-04
P2_B
C
D1
1N4003
C
G5
G6
G7
G8
G9
P8_DP
P6_E
P4_G
P3_F
U1
IC-VFD;UCN5812AF,DIP,28P
P10_H
F1
F1
1
2
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
VCCVDISP
G9
dp P8
VCCVDISP
h
P10
0123456789
G8
P7
d
P5 c
G7
P2 b
G10
P4
g
V1
VFD;10-LT-50G/GK,10DIG,FUTABA
G6
P1
a
G5
f P3
CON-BOX;8P,2.5MM,ST
B
G4
1
A
G3
3
4
5
6
7
8
9
10
11
12
P8_DP
G10
G9
G8
G7
G6
G5
G4
G3
G2
G1
G2
13
14
15
16
17
18
19
20
21
22
G1
23
24
VF1
12-8
SAM4S ER-5100 SERIES
4
3
2
1
SAM4S ER-5100 SERIES
12-9
4
3
2
1
A
B
e P6
h
P10
P4
g
P7
d
f P3
P2 b
P5 c
P1
a
com P9
dp P8
B
VCC
CON-BOX;11P,2MM,ST
CON-BOX;11P,2MM,ST
VCC
1 VF1
2 P6_E
3
4 P1_A
5
P2_B
6 P5_C
7 P8_DP
8 P7_D
9 SEN_DISPDISCON
10 G1
11
P1_A
P2_B
P3_F
P4_G
P5_C
P6_E
P7_D
P8_DP
G2
G10
G9
G8
G7
G6
G5
G4
G3
G2
G1
VF1
1
2
F1
F1
G10
G9
G8
G7
G6
G5
G4
G3
G2
G1
13
14
15
16
17
18
19
20
21
22
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
3
4
5
6
7
8
9
10
11
12
23
24
0123456789
CN1:A BLK
CN1:B
CN1:C
CN1:D
CN1:E
CN1:F
CN1:G
CN1:H
CN1:I
CN1:J
CN1:K
1
P3_F
2
P4_G
3 G10
4 G9
5 G8
6 G7
7 G6
8
G5
9 G4
10 SEN_DISPDISCON
11 G3
V1
VFD;10-LT-50G/GK,10DIG,FUTABA
CN2:A BLUE
CN2:B
CN2:C
CN2:D
CN2:E
CN2:F
CN2:G
CN2:H
CN2:I
CN2:J
CN2:K
F2
F2
C
C
D
VFD REAR PART
V1.0
Drawn by Hyun-Oh,Yun
1 of 1
Sheet
TITLE : ER-350/5100/5200/6500 DISPLAY Rev
Date
2002.10.28
File Name ER5200REARVFD.SCH
A3
Size
Shin Heung Precision Co., Ltd.
D
4
3
2
1
12-10
SAM4S ER-5100 SERIES
A(0:16)
D(0:7)
A16
A11
A10
A9
A8
A12
A13
A14
A15
A0
A1
A2
A3
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
A17
D0
D1
D2
D7
D6
D5
D4
D3
/CE
A4
A5
A6
A7
R7
10K
Note] R7 : 512K /OE(Read) Floating 방지
R2,R6 : 560ohm Stress Over 관련 1.2K 병렬로..
BOARD-IN HAR,30P
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
CN1
VCC
C2
100nF
(CHIP)
ZD1
1N4735A
6.2V
C1
100nF
(AXIAL)
JP1
0
R1
4.7K
R2
1.2K
R4 1.2K
R6
1.2K
1
2
3
R5
4.7K
VCC
D2
DIODE-SK14
Q1
MMBT2222A
V1
DIODE-SK14
D1
VCC
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
U1
GND
VCC
NC
CE
OE
D0
D1
D2
D3
D4
D5
D6
D7
27C512
27C1001
27C4001
PGM
VPP
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
16
32
30
22
24
13
14
15
17
18
19
20
21
VCC
O
O
O
X
JP2
RA1
ZD1
JK92-00132A
JK92-00132B
JK92-00132C
512Kbits
1Mbits
2Mbits
ASS'Y CODE NO.
X
O
JP1
O
X
X
O
C1
O
O
X
X
X
2Mbits
JP2
0
R3
RA1 4.7K
RES-NETWORK
EPROM Size 512Kbits 1Mbits
MANUAL INSERT
31
1
12
11
10
9
8
7
6
5
27
26
23
25
4
28
29
3
2
VCC
0
(AXIAL TYPE)
A17
/CE
D7
D6
D5
D4
D3
D2
D1
D0
2Mbit FISCAL PCB
2004-01-09
512K/1M/2M FISCAL PCB
1
1.3
1
KSH/CKW
SAM4S ER-5100 SERIES
12-11
470pF
CCC3
22pF
CCC4
22pF
22pF
2.2K
CCC2
CR2
CX1
16 MHz
CCC1
1M
CR1
4
3
2
1
LF
5
6
7
8
FERRITE
CBD1
GND
VO
VI
VCC
FS741
REF
XOUT
XIN
CU1
CR3
47K
CR4
47K
CR8
47K
CR7
47K
SER-65XX USE
750
CR6
0.1uF
CCC5
CBD2
CLOCK
FERRITE
SER-6500 CLOCK
( To Main CPU pin 59(X1) )
CCE1
100uF
16V
100
CR5
VCC
VCC
INT0(39)
CS1(37)
D3(35)
D4(33)
D5(31)
D6(29)
D7(27)
A2(24)
_RD(1)
RESET(57)
A(0:17)
DSR0
SIN0
_CS0
DTR0
SOUT0
AD(0:17)
DTR1
CN10
SOUT1
*DTR1
*RTS1
*CTS1
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
GND
VCC
*RTS0
*DTR0
SOUT0
12
14
16
18
20
22
11
13
15
17
19
21
From Main circuit
8
10
6
5
9
4
3
7
2
1
RED BLU
AD(0)
AD(1)
AD(2)
AD(3)
AD(4)
AD(5)
AD(6)
AD(7)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
IC15
TL16C452
VCC
INT1(38)
CS0(36)
D2(34)
D1(32)
D0(30)
A0(28)
A1(26)
_WR(100)
A(2)
A(1)
A(0)
SOUT1
9
8
7
6
5
4
3
2
1
68
67
66
65
64
63
62
61
GND5
*RLSD1
GND6
*RI1
*DSR1
CLK
*CS1
GND7
*LPTOE
*ACK
PE
BUSY
SLCT
VCC3
*ERROR
SIN1
GND8
GND2
*CTS0
*RLSD0
*RIO
*DSRO
*CS0
A2
A1
A0
*IOW
*IOR
*CS2
*RESET
VCC1
SIN0
GND3
GND4
IR1
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
IR3
IR4
IQ1
IQ2
1
3
1
3
12
14
16
18
20
22
13
15
17
19
21
8
7
11
6
5
10
4
3
9
2
1
CN22
RED BLU
KSC945-G
2
2
INT0
INT1
From Interface circuit
INT0
CS1
D3
D4
D5
D6
D7
A2
_RD
RESET
10K
_RESET
_RD
VCC
_WR
INT1
INT2
*SLIN
*INT
*AFD
*STB
GND1
PD0
PD1
PD2
PD3
PD4
PD5
PD6
PD7
INT0
BD0
10K
10K
KSC945-G
ICC12
2.2nF
ICC13
2.2nF
INT1
CS0
D2
D1
D0
A0
A1
_WR
VCC
DSR0
DTR0
SOUT0
SIN0
DSR1
DTR1
SOUT1
SIN1
10uF
VCC
10uF
10uF
10uF
C1-3
C2+ 4
C2- 5
V- 6
14T1OUT
13 R1IN
12R1OUT
11 T1IN
V- 6
11 T1IN
IX1
8MHz
3
1
NC
2
GND
VCC OUT
4
VCC
IC16
MAX232ACSE
9R2OUT R2IN 8
10 T2IN T2OUT 7
C2- 5
12R1OUT
C1- 3
14T1OUT
C2+ 4
V+ 2
15 GND
13 R1IN
C1+ 1
16 VCC
IC14
MAX232ACSE
9R2OUT R2IN 8
10 T2IN T2OUT 7
C1+1
V+ 2
16 VCC
15 GND
IR2
ICE10
ICE8
ICE7
ICE5
ICE3
ICE2
1K
10uF
4.7uF
4.7uF
10uF
4.7uF
4.7uF
OSC
IFB8
IFB6
IFB5
IFB7
IFB4
IFB2
IFB1
IFB3
0.1uF
ICC3
ICE4
ICE1
ICE9
ICE6
0.1uF
0.1uF
470pF
VCC
VCC
0.1uF
ICC8
ICC4
ICC7
470pF
ICC1
470pF
ICC6
OSC
_CS1
SIN1
DSR1
5
9
2
3
4
6
CN20
RS232C9A
5
9
2
3
4
6
CN18
RS232C9A
ICC9
0.1uF
ICC2
470pF
ICC5
VCC
ICC10
0.1uF
VCC
ICC11
0.1uF
VCC
ICE11
100uF
12-12
SAM4S ER-5100 SERIES
UPDATE LOG
Application
Date
Page
Part #
Notes (Cause & Solution)
S/Bulletin
Use this page to record any special servicing information such as Service Bulletins or Supplements.
When possible, record changes to Code numbers directly on the actual Parts List. Always record Service Bulletin numbers
and Application Dates on this log to ensure that your data is always as current as possible.
SAM4S ER-5100 SERIES
ⓒ
Shin Heung Precision. March 2004
Printed in KOREA
V1.0
Code No. : JK68-60918A