Download ACR Electronics ME406 Series Troubleshooting guide
Transcript
DESCRIPTION, INSTALLATION, OPERATION AND MAINTENANCE MANUAL REMOTE SWITCH 453-0023, MODULE INTERFACE 453-1101 AND BUZZER 452-6505 INSTALLATION 570-0023 Rev. G Artex Products / ACR Electronics, Inc. Artex Products / ACR Electronics, Inc. 5757 Ravenswood Road, Fort Lauderdale, Florida USA Phone 954-981-3333, Fax 954-983-5087 www.acrartex.com Artex Products / ACR Electronics, Inc. 570-0023 Rev. G Notices 1. This document discloses subject matter in which ACR Electronics, Inc. has proprietary rights. Neither receipt nor possession thereof confers or transfers any right to reproduce or disclose the document, any part thereof, any information therein, or any physical article or device, or practice any method or process except by written permission from or written agreement with ACR Electronics, Inc. 2. This manual is subject to regular updates and changes. 3. Cell Warning: 131-0001 CELL WARNING: DO NOT RECHARGE, SHORT-CIRCUIT, DISASSEMBLE, DEFORM, HEAT OR PLACE NEAR A DIRECT FLAME Page 2 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G List of Affected Pages PAGE # DATE REASON FOR CHANGE TITLE 04/16/09 DCN 2818, 2929, 3418, 3459, ECO 15051, ECO 15431 1 04/16/09 DCN 2819, 2825, 3418, ECO 15051 2 04/16/09 DCN 2818, 2929, 3418, ECO 15051 3 04/16/09 DCN 2818, 2929, 3068, 3418, 3459, ECO 15051, ECO 15431 4 04/16/09 DCN 2818, 2929, 3068, 3418, ECO 15051 5 04/16/09 DCN 3068, 3418, 3459, ECO 15051, ECO 15431 6 04/16/09 DCN 3068, 3418, ECO 15051 7 04/16/09 DCN 3068, 3418, ECO 15051 8 04/16/09 DCN 2819, 2825, 3068, 3418, ECO 15051 9 04/16/09 DCN 3068, 3418, 3459, ECO 15051 10 04/16/09 DCN 3068, 3418, 3459, ECO 15051 11 04/16/09 DCN 3068, 3418, 3459, ECO 15051, ECO 15431 12 04/16/09 DCN 3068, 3418, 3459, ECO 15051, ECO 15431 13 04/16/09 DCN 3068, 3418, 3459, ECO 15051 14 04/16/09 DCN 3068, 3418, 3459, ECO 15051 15 04/16/09 DCN 3068, 3418, 3459, ECO 15051 16 04/16/09 DCN 3068, 3418, ECO 15051 17 04/16/09 DCN 3068, 3418, ECO 15051 18 04/16/09 DCN 3068, 3418, 3459, ECO 15051 19 04/16/09 DCN 3068, 3418, ECO 15051 20 04/16/09 DCN 3068, 3418, 3459, ECO 15051, ECO 15431 21 04/16/09 DCN 3068, 3418, ECO 15051, ECO 15431 22 04/16/09 DCN 3068, 3418, ECO 15051 23 04/16/09 DCN 3068, 3418, ECO 15051 24 04/16/09 DCN 3068, 3418, ECO 15051 25 04/16/09 DCN 3068, 3418, ECO 15051 26 04/16/09 DCN 3068, 3418, ECO 15051 27 04/16/09 DCN 3068, 3418, ECO 15051 28 04/16/09 DCN 3068, 3418, ECO 15051 29 04/16/09 DCN 3068, 3418, ECO 15051 Page 3 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G PAGE # DATE REASON FOR CHANGE 30 04/16/09 DCN 3068, 3418, ECO 15051 31 04/16/09 DCN 3418, ECO 15051 32 04/16/09 DCN 3418, ECO 15051 33 04/16/09 DCN 3418, ECO 15051 Page 4 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G Revision History REVISION ENGINEERING CHANGE ORDER DATE - RELEASE 06/02/06 A DCN 2819, 2825 11/01/06 B DCN 2818, 2929 01/29/07 C DCN 3068 02/14/08 D DCN 3418 04/16/09 E DCN 3459 07/27/09 F ECO 15051 4/30/12 G ECO 15431 7/25/13 Page 5 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G Table of Contents 1. INTRODUCTION ................................................................................................8 2. PARTS LIST .......................................................................................................8 3. WIRING PIN OUT .............................................................................................9 4. HARNESS ....................................................................................................... 10 5. WIRING DIAGRAMS ...................................................................................... 11 6. 453-0023 REMOTE SWITCH INSTALLATION ................................................. 13 6.1 AMERI-KING AND ACK INSTALLATION RETROFIT .............................................................. 13 6.2 TYPICAL INSTALLATION .............................................................................................. 15 6.3 PANEL CUTOUT INSTRUCTIONS .................................................................................... 16 7. INSTALLATION .............................................................................................. 18 7.1 INSTRUCTIONS......................................................................................................... 18 8. 453-1101 MODULE INTERFACE INSTALLATION ............................................ 20 8.1 INSTRUCTIONS......................................................................................................... 20 9. 453-1101 MODULE INTERFACE AND 452-6505 BUZZER WIRING ................ 21 9.1 INSTRUCTIONS......................................................................................................... 21 10. REMOTE SWITCH CELL REPLACEMENT .......................................................... 21 10.1 CELL SHELF LIFE ...................................................................................................... 21 10.2 MATING COVER REMOVAL ........................................................................................... 22 10.3 CELL REPLACEMENT FROM CELL HOLDER WITH STAND ALONE SPRING .................................... 22 10.4 CELL REPLACEMENT FROM CELL HOLDER WITH BUILT-IN SPRING .......................................... 26 10.5 MATING COVER INSTALLATION ..................................................................................... 29 10.6 CELL DISPOSAL INSTRUCTIONS .................................................................................... 30 11. TROUBLESHOOTING GUIDE .......................................................................... 30 12. SPECIFICATIONS ........................................................................................... 31 12.1 COMPONENTS DIMENSIONS ......................................................................................... 31 12.3 ENVIRONMENTAL CATEGORIES ..................................................................................... 32 13. INDEX ............................................................................................................ 33 Page 6 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G List of Figures Figure 1: Wiring Diagram for Shielded Cable (Composite Aircraft) ........................................................ 11 Figure 2: Wiring Diagram for Unshielded Telephone Cable ................................................................... 11 Figure 3: Wiring Diagram for Shielded Cable (Metal Aircraft) ................................................................ 12 Figure 4: Wiring Diagram for Unshielded Telephone Cable (Metal Aircraft) ............................................ 12 Figure 5: Labels 591-0003 & 591-3029 ............................................................................................... 16 Figure 6: Panel Cutout Dimensions ..................................................................................................... 16 Figure 7: Harness to Remote Switch Connection ................................................................................. 18 Figure 8: Remote Switch Orientation .................................................................................................. 18 Figure 9: Remote switch wire tensile load release ............................................................................... 19 Figure 10: Module Interface to ELT Connection ................................................................................... 20 Figure 11: Spring Configuration.......................................................................................................... 22 Figure 12: Conical Spring ................................................................................................................... 23 Figure 13: Conical Spring Installation ................................................................................................. 23 Figure 14: Cell Holder Wires .............................................................................................................. 24 Figure 15: Ground Wire ..................................................................................................................... 25 Figure 16: Cell Installation ................................................................................................................. 26 Figure 17: Spring Installation ............................................................................................................. 26 Figure 18: Spring Fit.......................................................................................................................... 27 Figure 19: Cell Holder Wires .............................................................................................................. 27 Figure 20: Ground Wire ..................................................................................................................... 28 Figure 21: Mating Cover Installation ................................................................................................... 29 Figure 22: Retaining Screws Installation ............................................................................................. 29 Figure 23: 453-0023 Remote Switch ................................................................................................... 31 Figure 24: 453-1101 Module Interface ................................................................................................ 31 Page 7 of 33 Artex Products / ACR Electronics, Inc. 1. 570-0023 Rev. G INTRODUCTION This manual contains detailed information to install the self-powered remote switch 453-0023, module interface 453-1101, and the buzzer 452-6505. In addition, these instructions highlight the methodology to replace the cell in the remote switch. This manual is not intended to be an installation for the ELT system. Use this manual in conjunction with any of Artex ME406 series ELT manuals. 2. PARTS LIST The following parts should be included with the 455-0023 and 455-7420 Pack Lists. Please contact ACR Electronics, Inc., if shortages are found. QUANTITY PART NUMBER DESCRIPTION 455-0023 Pack List, Self-Powered Remote Switch 4 ea. 209-0002 Screw, 4-40 X 1/2, SOC, SS, BLK 4 ea. 241-0400 HEX Nut, 4-40 Reduced Dim. 1 ea. 453-0023 Remote Switch, Self-Powered Assembly 1 ea. 570-0023 Manual, Remote Switch 453-0023, Module Interface 453-1101 and Buzzer 452-6505 Installation 1 ea. 591-0003 Label, 453-0023 Remote Switch Horizontal 1 ea. 591-0036 Label, Cell Replacement Warning 1 ea. 591-3029 Label, 453-0023 Remote Switch QUANTITY PART NUMBER DESCRIPTION 455-7420 Pack List, ME406 Install Kit 4 ea. 201-0810 Screw, PHP 8-32 x 5/8 SS 4 ea. 241-0832 Nut, HEX 8-32 x 1/4 SS 4 ea. 246-0008 2 ea. 850-0814 Washer, Flat, SS .036”-.045" THK Sealant Strip, D-sub Connector Page 8 of 33 Artex Products / ACR Electronics, Inc. 3. 570-0023 Rev. G WIRING PIN OUT The following information highlights the pin out of the remote switch and module interface. Remote Switch Back View VIEW PIN 2 PIN # SIGNAL DESCRIPTION 2 Light 3 External On 4 Reset 1 5 Reset 2 PIN # SIGNAL DESCRIPTION 2 Light 5 G-Switch Loop 6 Reset 1 7 Ground 8 Horn Power 12 G-Switch Loop 13 Reset 2 14 External ON PIN # SIGNAL DESCRIPTION 2 Light 3 External On 4 Reset 1 5 Reset 2 Module Interface Front View VIEW Module Interface Back View VIEW PIN 2 Page 9 of 33 Artex Products / ACR Electronics, Inc. 4. 570-0023 Rev. G HARNESS Due to the large array of configurations possible, ACR Electronics, Inc. does not provide a harness or RJ11 plugs (telephone connector) as part of the installation of the ELT. Accordingly, it is the responsibility of the installer to manufacture a harness or ensure that the existing harness is adequate for the installation. The harness must be manufactured following the cross-wired configuration mentioned in Subsection 6.2. NOTE: Refer to Subsection 6.1 for Ameri-King and ACK retrofit installations. Artex recommends using a shielded cable to prevent signals related to power frequency, audio frequency and electrical transients generated from on-board equipments from interfering with the ELT operation. Although it might be appropriate to use a telephone line (minimum UL flammability rating VW1) in some instances, each installation is different and should be evaluated on a case by case basis. Accordingly, it is the responsibility of the ELT installer to ensure that the installations follow FAA regulations such as but not limited to Advisory Circular 43.13. Refer to the installation section of any of the ME406 series manuals for ELT related information. Page 10 of 33 Artex Products / ACR Electronics, Inc. 5. 570-0023 Rev. G WIRING DIAGRAMS Refer to the following wiring diagrams to connect the remote switch 453-0023, module interface 453-1101, and buzzer 452-6505 to the ME406 series ELT. NOTE: For Ameri-King or ACK ELT retrofit application, refer to Subsection 6.1. Figures 1 and 2 apply to composite aircraft, whereas Figures 3 and 4 apply to metal aircraft. 3 EMERGENCY LOCATOR TRANSMITTER (ELT) LIGHT 14 RESET 1 6 RESET 2 13 HORN POWER 8 GROUND 7 MODULE INTERFACE 453-1101 2 EXTERNAL ON HARNESS 4-CONDUCTOR CABLE (SHIELDED) GPS REMOTE SWITCH 453-0023 2 2 5 2 LIGHT 3 3 4 3 EXTERNAL ON 4 4 3 4 RESET 1 5 5 2 5 RESET 2 BRAID BRAID 2 2 1 2 HORN 452-6505 ANTENNA 1 #26 AWG RED WIRE 2 #26 AWG BLACK WIRE 3 #26 AWG BLUE WIRE CAP & STOW Figure 1: Wiring Diagram for Shielded Cable (Composite Aircraft) 3 EMERGENCY LOCATOR TRANSMITTER (ELT) LIGHT 14 RESET 1 6 RESET 2 13 HORN POWER 8 GROUND 7 MODULE INTERFACE 453-1101 2 EXTERNAL ON HARNESS 4-CONDUCTOR TELEPHONE CABLE (UNSHIELDED) GPS REMOTE SWITCH 453-0023 2 2 5 2 LIGHT 3 3 4 3 EXTERNAL ON 4 4 3 4 RESET 1 5 5 2 5 RESET 2 2 2 ADDITIONAL WIRE (ACROSS AIRCRAFT) 1 2 HORN 452-6505 ANTENNA 1 #26 AWG RED WIRE 2 #26 AWG BLACK WIRE 3 CAP AWG & STOW #26 BLUE WIRE Figure 2: Wiring Diagram for Unshielded Telephone Cable (Composite Aircraft) Page 11 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G Figures 3 and 4 apply to metal aircraft. 3 EMERGENCY LOCATOR TRANSMITTER (ELT) LIGHT RESET 1 RESET 2 14 6 13 HORN POWER 8 GROUND 7 MODULE INTERFACE 453-1101 2 EXTERNAL ON HARNESS 4-CONDUCTOR CABLE (SHIELDED) GPS REMOTE SWITCH 453-0023 2 2 5 2 LIGHT 3 3 4 3 EXTERNAL ON 4 4 3 4 RESET 1 5 5 2 5 RESET 2 2 2 1 2 HORN 452-6505 ANTENNA 1 #26 AWG RED WIRE 2 #26 AWG BLACK WIRE 3 CAP AWG & STOW #26 BLUE WIRE Figure 3: Wiring Diagram for Shielded Cable (Metal Aircraft) 3 EMERGENCY LOCATOR TRANSMITTER (ELT) LIGHT RESET 1 RESET 2 14 6 13 HORN POWER 8 GROUND 7 MODULE INTERFACE 453-1101 2 EXTERNAL ON HARNESS 4-CONDUCTOR TELEPHONE CABLE (UNSHIELDED) GPS REMOTE SWITCH 453-0023 2 2 5 2 LIGHT 3 3 4 3 EXTERNAL ON 4 4 3 4 RESET 1 5 5 2 5 RESET 2 2 2 1 2 HORN 452-6505 ANTENNA 1 #26 AWG RED WIRE 2 #26 AWG BLACK WIRE 3 CAP AWG & STOW #26 BLUE WIRE Figure 4: Wiring Diagram for Unshielded Telephone Cable (Metal Aircraft) Page 12 of 33 Artex Products / ACR Electronics, Inc. 6. 453-0023 REMOTE SWITCH INSTALLATION 6.1 Ameri-King and ACK Installation Retrofit 570-0023 Rev. G Ameri-King retrofit: The remote switch 453-0023 and ME406 series ELT cannot be used in conjunction with the Ameri-King interconnecting cable unless extender 611-0018 is connected directly with the Ameri-King cable. This 611-0018 extender is provided as part of the ELT installation pack list or can be ordered as line item. The 611-0019 flat cable can be discarded since it is intended for ACK retrofit. AMERI-KING CABLE (INSIDE AIRCRAFT) EXTENDER 611-0018 EXTENDER 611-0018 Page 13 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G ACK retrofit: The remote switch 453-0023 and ME406 series ELT cannot be used in conjunction with the ACK interconnecting cable unless Flat Cable 611-0019 is connected directly with the ACK cable. This 611-0019 cable is provided as part of the ELT installation pack list or can be ordered as line item. The cable is installed on the ELT side. The 611-0018 extender can be discarded since it intended for Ameri-King ELT retrofit. FLAT CABLE 611-0019 ACK CABLE (INSIDE AIRCRAFT) FLAT CABLE 611-0019 611-0019 Wiring C1 2 3 4 5 C2 5 4 3 2 C1 C2 PIN 2 Page 14 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G 6.2 Typical Installation 6.2.1 Due to the large array of configurations possible, ACR Electronics, Inc. does not provide a harness or RJ11 plugs (telephone connector) as part of the installation of the ELT. 6.2.2 The harness must be manufactured following the cross-wired configuration shown below. NOTE: Refer to Subsection 6.1 for ACK and Ameri-King retrofits. Wiring C1 2 3 4 5 C2 5 4 3 2 C1 C2 PIN 2 Page 15 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G 6.3 Panel Cutout Instructions 6.3.1 Select a mounting location where the remote switch can be seen from the pilot’s seated location, easily be reached by the pilot, out of direct sunlight, and can accommodate the remote switch and the label. Depending on the remote switch orientation on the control panel, choose the appropriate label and discard the other one. Label 591-0003 and label 591-3029 are provided in the 455-0023 pack list. Figure 5: Labels 591-0003 & 591-3029 6.3.2 Create a cutout in the panel for the remote switch according to the minimum dimensions specified below and drill four 1/8” diameter holes. The dimensions apply to both 591-0003 and 591-3029 labels. Adjust the hole-pattern appropriately on the panel depending on the orientation of the remote switch. NOTE: For Ameri-King retrofit applications, use the existing mounting holes since the face plate of the remote switch is designed to accommodate that hole-pattern. Tolerance: +.020, -.000 Figure 6: Panel Cutout Dimensions Page 16 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G 6.3.3 Clean the application surface area thoroughly prior to applying label 591-0003 or 5913029. 6.3.4 Remove the paper backing from the label and line up the label over the cutout. 6.3.5 Press firmly and evenly over the label to produce maximum adhesion. 6.3.6 Trim the label with an Exacto knife if it partially covers the mounting holes. Page 17 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G 7. INSTALLATION 7.1 Instructions 7.1.1 Feed the modular jack connector from the harness through the panel cutout. 7.1.2 Plug the modular jack connector to the remote switch. Figure 7: Harness to Remote Switch Connection 7.1.3 Slide the remote switch and the harness inside the cutout following the orientation shown below. 7.1.4 Secure the remote switch using the hardware provided in the 455-0023 pack list. Use a 1/16 hex socket for the nuts and a small Phillips screwdriver for the screws. The torque on the screws is 4.0 Lb-in (± 0.5 Lb-in). Figure 8: Remote Switch Orientation Page 18 of 33 Artex Products / ACR Electronics, Inc. 7.1.5 570-0023 Rev. G Fasten the ground wire along the harness within one inch of the remote switch using a tie cable. NOTE: The ground wire should have enough slack to prevent tensile load. Figure 9: Remote switch wire tensile load release (Panel not shown) 7.1.6 Connect the remote switch 26 AWG ground wire according to the wiring diagrams highlighted in section 5 using a ring or a fork terminal quick disconnect. NOTE: Secure an additional wire to the ground wire with a butt slice to extend the length if necessary. 7.1.7 Fasten the harness to the aircraft. Ensure that the harness has enough slack to prevent tensile load on the modular jack connector of the remote switch. 7.1.8 Plug the modular jack connector of the harness to the module interface 453-1101 if it is already installed. 7.1.9 Refer to the Transmitter Test section of the ME406 series ELT manuals to check the operation of the complete connection to the ELT. 7.1.10 Apply Cell Replacement Warning label 591-0036 from kit 455-0023 inside the aircraft’s logbook. The intent of the label is to remind the pilot to change the cell inside the remote switch every five years or sooner depending on usage. 7.1.11 Enter the date, installer’s initials and whether the ELT passed or failed into the aircraft’s logbook. Page 19 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G 8. 453-1101 MODULE INTERFACE INSTALLATION 8.1 Instructions 8.1.1 Place the two sealing strips 850-0814 provided in the 455-7420 install kit into the ELT 15-pin D-sub connector. 8.1.2 Insert the module interface 453-1101 into the ELT D-sub and secure it in place using the two thumbscrews. The torque on the thumbscrews is 4 to 5 Lb-in. Figure 10: Module Interface to ELT Connection (Red Wire - Horn Power, Black Wire - A/C Ground, Blue Wire – Cap & Stow) 8.1.3 Fasten the three wires along the harness within one inch of the module interface using cable ties. NOTE: The length of the wires between the end of the module and the first cable tie should have enough slack to provide strain relief. 8.1.4 Fasten the harness to the aircraft. Ensure that the harness has enough slack to prevent tensile load on the modular jack connector of the module interface. 8.1.5 Plug the modular jack connector of the harness to the remote switch 453-0023 if it is already installed. 8.1.6 Refer to the Transmitter Test section of the ME406 series ELT manuals to check the operation of the complete connection to the ELT. 8.1.7 Enter the date, installer’s initials and whether the ELT passed or failed into the aircraft’s logbook. Page 20 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G 9. 453-1101 MODULE INTERFACE AND 452-6505 BUZZER WIRING 9.1 Instructions 9.1.1 Follow the appropriate wiring diagram in Section 5, depending if the aircraft is metal or composite. Connect RED wire to Horn Power connection Connect BLACK wire to A/C Ground Cap & stow BLUE wire 9.1.2 Mount the buzzer according to the instructions highlighted in the ME406 series ELT manuals. NOTE: Allow enough slack to prevent tensile load on the wires leading from the module interface and the buzzer. Depending on the location of the buzzer, additional wires can be strung between the buzzer and the module interface. 10. REMOTE SWITCH CELL REPLACEMENT 131-0001 CELL WARNING: DO NOT RECHARGE, SHORT-CIRCUIT, DISASSEMBLE, DEFORM, HEAT OR PLACE NEAR A DIRECT FLAME 10.1 Cell Shelf Life 10.1.1 The shelf life of the cell is 5 years. The cell is available through ACR Electronics, Inc. under part number 131-0001. 10.1.2 The Lithium content of the cell is less than 0.15 Gram. Page 21 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G 10.2 Mating Cover Removal 10.2.1 Remove the four retaining nuts and screws securing the remote switch 453-0023 to the panel. 10.2.2 Slide the remote switch from the panel. 10.2.3 Cut the tie cables securing the ground wire to the harness. 10.2.4 Disconnect the modular jack connector of the harness from the remote switch. 10.2.5 Remove the four retaining screws from the remote switch to access the cell compartment. 10.2.6 Remove the protective cover opposite of the product label. 10.3 Cell Replacement from Cell Holder with Stand Alone Spring 10.3.1 At this point, two options are available depending on the manufacturing date of the remote switch: Spring Spring The remote switch was manufactured with an individual spring unattached to the cell holder. Accordingly, proceed with the following instructions. This newest version of the remote switch was manufactured with a built-in spring permanently attached to the cell holder. Accordingly, proceed to section 10.4. Figure 11: Spring Configuration Page 22 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G 10.3.2 Carefully remove the cell 131-0001 from the plastic cell holder and keep the conical spring. Spring Figure 12: Conical Spring 10.3.3 Dispose of the cell according to the instructions specified in section 10.6. 10.3.4 Carefully slide the replacement cell 131-0001 inside the plastic cell holder following the polarity mentioned inside the holder and on the cell, or by matching the positive (+) end of the cell to the red wire side of the holder. 10.3.5 Install the conical spring between the positive side of the cell and the cell holder. 10.3.6 Push the cell against the conical spring. Figure 13: Conical Spring Installation Page 23 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G 10.3.7 Gently route the black and red wires from the plastic cell holder away from the leads of the rocker switch if necessary. Wires away from PCB Figure 14: Cell Holder Wires Page 24 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G 10.3.8 Position the ground wire (black) along the side of the plastic cell holder and away from the screw boss. Black Wire Screw boss Figure 15: Ground Wire 10.3.9 Refer to Subsection 10.5 to install the mating cover. Page 25 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G 10.4 Cell Replacement from Cell Holder with Built-in Spring 10.4.1 Carefully remove the cell 131-0001 from the plastic cell holder. 10.4.2 Dispose of the cell according to the instructions specified in Subsection 10.6. 10.4.3 Carefully slide the negative end of the replacement cell 131-0001 inside the plastic cell holder following the polarity mentioned inside the holder and on the cell, or by matching the positive (+) end of the cell to the red wire side of the holder. Figure 16: Cell Installation 10.4.4 Pull the built-in spring away from the end of the cell using tweezers and slide the cell inside the holder. Figure 17: Spring Installation Page 26 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G 10.4.5 Release the spring and ensure that it is properly pushing against the end of the cell. Figure 18: Spring Fit 10.4.6 Gently route the black and red wires from the plastic cell holder away from the leads of the rocker switch if necessary. Wires away from PCB Figure 19: Cell Holder Wires Page 27 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G 10.4.7 Position the ground wire (black) along the side of the plastic cell holder and away from the screw boss. Black Wire Screw boss Figure 20: Ground Wire Page 28 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G 10.5 Mating Cover Installation 10.5.1 Install the mating cover to the assembly by matching the cutouts according to the different components. 10.5.2 Ensure that the 26 AWG ground wire is properly fed through the notch of the mating cover and is not pinched by the screw boss. Mating cover Figure 21: Mating Cover Installation 10.5.3 Secure the covers together using the retaining screws previously removed. The torque on the screws is 2.0 Lb-in (+0 Lb-in, - 0.5 Lb-in). Figure 22: Retaining Screws Installation 10.5.4 Refer to section 7 to install the remote switch back on the panel. 10.5.5 Refer to the Transmitter Test section of the ME406 series ELT manuals to check the operation of the complete connection to the ELT. 10.5.6 Apply Cell Replacement Warning label 591-0036 from kit 455-0023 inside the aircraft’s logbook. The intent of the label is to remind the pilot to change the cell inside the remote switch every five years or sooner depending on usage. 10.5.7 Enter the date, installer’s initials and whether the ELT passed or failed into the aircraft logbook. Page 29 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G 10.6 Cell Disposal Instructions Lithium batteries are best disposed of as a non-hazardous waste when fully or mostly discharged. The Federal Environmental Protection Agency (EPA) governed by the Resource Conservation and Recovery Act (RCRA) do not list or exempt Lithium as a hazardous waste. However, if waste lithium batteries are still fully charged or only partially discharged, they can be considered a reactive hazardous waste because of the significant amounts of un-reacted or unconsumed lithium remaining in the spent battery. The batteries must be neutralized through an approved secondary treatment facility prior to disposal as a hazardous waste (as required by the U.S. Land Ban Restrictions for the hazardous and Solid Waste Amendments of 1984.) Secondary treatment centers receive these batteries as manifested hazardous waste under code "D003 - reactive". Button cells are exempt because they contain so little lithium and therefore can be disposed of in the normal municipal waste stream. 11. TROUBLESHOOTING GUIDE Refer to the ME406 series ELT manuals for flash error codes during Self-Test. SYMPTOM LED of the remote switch is not flashing when either the ELT or the remote switch is turn ON. LIKELY CAUSE ACTION The voltage of the cell is below 3.3 volts. Replace the cell. The harness is not secured to the remote switch. Check that the modular jack is fully inserted inside the back of the remote switch. The remote switch ground wire is not connected to the module interface ground. For a metallic aircraft, check the resistance between the remote switch and the module interface (10 Ω min.) The module interface is not connected to the ELT. Check the connection. Cell is not installed properly. Check the polarity of the cell with respect to the plastic cell holder. The wiring configuration is incorrect. Refer to Section 5. Page 30 of 33 Artex Products / ACR Electronics, Inc. 12. 570-0023 Rev. G SPECIFICATIONS 12.1 Components Dimensions The following dimensions are displayed in [millimeters] and inches. Figure 23: 453-0023 Remote Switch Figure 24: 453-1101 Module Interface 12.2 Components Weight PART NUMBER DESCRIPTION WEIGHT 452-6505 Buzzer, Piezo .34 oz (9.64 gr.) Max. 453-0023 Remote Switch, Self-Powered 1.30 oz (36.85 gr.) Max. 453-1101 Module Interface, ELT to Remote Switch 1 oz (28.35 gr.) Max. The buzzer 452-6505 is included with the ELT Pack List. Page 31 of 33 Artex Products / ACR Electronics, Inc. 570-0023 Rev. G 12.3 Environmental Categories DO-160D Environmental categories for nameplates: Remote switch 453-0023: DO-160D Env. Cat. F1XCAA[204]XWXXXXXXXXA[XXX]X[XXXX]XXX Module interface 453-1101: DO-160D Env. Cat D2XBA[204][204]XWXXXXXXXXA[XXX]X[XXXX]XXX Page 32 of 33 Artex Products / ACR Electronics, Inc. 13. 570-0023 Rev. G INDEX 4 455-0023 Pack List, 8 455-7420 Pack List, 8 5 591-0003 Label, 16 591-3029 Label, 16 6 611-0018 Extender, 13 611-0019 Cable, 14 L Label 591-0003, 16 Label 591-0036, 19, 29 Label 591-3029, 16 LED, 18, 30 List of Figures, 7 M Module Interface Installation, 20, 21 O Orientation, Remote Switch, 18, 19 A ACK retrofit, 14 Advisory Circular 43.13-2A, 10 Ameri-King retrofit, 13 P Panel Cutout Dimensions, 16 Panel Cutout Instructions, 16 Parts List, 8 B Buzzer 452-6505, 11 C Cell Disposal Instructions, 30 Cell Shelf Life, 21 Cell Warning, 21 R Remote Switch Installation, 13 Replacement, Cell Remote Switch, 21 S Shelf Life, Cell, 21 Specifications, 31 D Dimensions, Components, 31 E Environmental Categories, 32 G Ground Wire, Remote Switch, 19 H Harness, 10 T Telephone Line, 10 Troubleshooting Guide, 30 W Weight, Components, 31 Wiring Diagram for shielded cable (Composite Aircraft), 11 Wiring Diagram for telephone line (Composite Aircraft), 11 Wiring Diagram for telephone line (Metallic Aircraft), 12 I Installation, Module Interface, 20, 21 Installation, Remote Switch, 13 Page 33 of 33