Download Acura 2014 RDX REMOTE CONTROL Service manual
Transcript
INSTALLATION INSTRUCTIONS Accessory Application REMOTE CONTROL ENGINE STARTER 2014 RDX PARTS LIST Publications No. BII 48865 Issue Date MARCH 2013 3 Relays Remote Engine Starter Unit Kit P/N 08E91-E54-200 Transmitter 15 Wire ties Control unit 3 Long wire ties Antenna 8 Urethane tapes ID label Clip Remote Control Engine Starter Attachment Kit P/N 08E92-E54-200A Engine starter harness Caution label Fuse label Control unit bracket © 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 48865 (1303) 08E92-E54-2A00-90 1 of 25 Accessory User’s Information Manual Illustration of the Remote Control Engine Starter in the Vehicle ANTENNA Quick Start Guide CONTROL UNIT TOOLS AND SUPPLIES REQUIRED Flat-tip screwdriver Phillips screwdriver Ratchet 10 mm and 12 mm Sockets ENGINE STARTER HARNESS Isopropyl alcohol Shop towel 3A, 40A FUSES QB20801AK 3 RELAYS Tape measure Scissors INSTALLATION HDS/MVCI Masking tape Client Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” Diagonal cutters Ruler Electrical tape Pushpin Felt-tip pen 1. File Disconnect the negative cable from the battery. Eye protection (face shield, safety goggles, etc.) Drill 3 mm and 6 mm Drill bits The following tool is available through the Honda Tool and Equipment Program. On the iN, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under “Search”. Or, call 888-424-6857. • Plastic Trim Tool (T/N SILTRIMTL10) 2 of 25 BII 48865 (1303) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 2. Using isopropyl alcohol on a shop towel, clean the area where the ID label will attach. NOTE: The remote is factory set for driver 1 remote control. To program the driver 2 remote, follow the “REMOTE CONTROL ENGINE STARTER TRANSMITTER REGISTRATION” instructions on ISIS. 4. Using a plastic trim tool, remove the left and right lenses from the front roof module (two retaining tabs for each lens). VEHICLE CONNECTORS ID LABEL 6 RETAINING TABS FRONT ROOF MODULE TRANSMITTER 2 BOLTS 2 RETAINING TABS 2 RETAINING TABS RIGHT LENS LEFT LENS Clean with isopropyl alcohol. PLASTIC TRIM TOOL QB20939DH 3. Attach the “DRIVER 1” ID label to the transmitter in the area as shown. QB62650AK 5. Remove the front roof module (two bolts, six retaining tabs, and unplug the vehicle connectors). 6. Remove the driver’s and passenger’s sunvisor holders. PASSENGER’S SUNVISOR HOLDER (Rotate.) DRIVER’S SUNVISOR HOLDER (Rotate.) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 48865 (1303) QB62701AK 3 of 25 7. Remove the driver’s sunvisor: • • Pivot the right sunvisor downward. • Wrap tape around the tip of a flat-tip screwdriver. • Locate the slot in the bracket cover, and insert the flat-tip screwdriver into the slot. Push in and hold the retaining tab. • Remove the driver’s sunvisor (unplug the vehicle connector). VEHICLE CONNECTOR While holding the retaining tab, push up on the sunvisor and rotate it toward the door. NOTE: If the retaining tab did not stay pushed in, return the sunvisor to its original position and repeat this step. FLAT-TIP SCREWDRIVER BRACKET COVER RETAINING TAB DRIVER’S SUNVISOR QB22903AK TAPE 8. DRIVER’S SUNVISOR FRONT Remove the driver’s A-pillar trim. • Pull away the driver’s door opening seal from the driver’s A-pillar trim. • Pull out on the driver’s A-pillar trim to release three clips. Pull the clip. Make sure the retaining tab slides into the bracket cover. 2 CLIPS DRIVER’S A-PILLAR Push the retaining tab. While pushing in on the retaining tab, rotate the sunvisor toward the door. DRIVER’S A-PILLAR TRIM QB22902AK DRIVER’S DOOR OPENING SEAL (Pull away.) 4 of 25 BII 48865 (1303) QB22904AK © 2013 American Honda Motor Co., Inc. – All Rights Reserved. • To prevent clips from falling into the body panel area, carefully insert a shop towel between the driver’s A-pillar and the driver’s A-pillar trim. 9. DRIVER’S A-PILLAR TRIM Remove the remaining upper clip from the driver’s A-pillar. 2 TABS (Push.) DRIVER’S A-PILLAR UPPER CLIP (Discard.) QB22907AK SHOP TOWEL QB22905AK • Slide the driver’s A-pillar trim upward, and remove the driver’s A-pillar trim. • Remove the shop towel and any clips. 10. Install the new clip (supplied) to the driver’s A-pillar trim. NOTE: When reinstalling the A-pillar trim, refer to the service manual for the correct overlap procedure. CLIP (supplied) UPPER CLIP DRIVER’S A-PILLAR TRIM DRIVER’S A-PILLAR TRIM Q0N0533AH QB22906AK © 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 48865 (1303) 5 of 25 11. Pull away the driver’s door opening seal from around the driver’s dashboard side cover. 14. Pull away the door opening seal, and remove the driver’s kick panel (two clips). 2 CLIPS 3 HOOKS 3 RETAINING TABS 2 CLIPS DOOR OPENING SEAL (Pull away.) DRIVER’S DOOR OPENING SEAL (Pull away.) DRIVER’S KICK PANEL QB22908AK QB22910AK 15. Reconnect the negative cable to the battery. Press the engine start/stop button to select the ON mode. Lower the tilt lever, and release the column band (two clips). DRIVER’S DASHBOARD SIDE COVER 12. Remove the driver’s dashboard side cover (two clips, three retaining tabs, and three hooks). 13. Release the driver’s front door sill trim (five clips and two retaining tabs). STEERING WHEEL 3 CLIPS Raise. COLUMN BAND UPPER COLUMN COVER FRONT 2 RETAINING TABS DRIVER’S FRONT DOOR SILL TRIM 2 CLIPS QB22909AK 2 CLIPS STEERING WHEEL 6 of 25 BII 48865 (1303) QA00802BX © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 16. Turn the steering wheel 90° clockwise. Using a plastic trim tool, release the lock as shown. 18. Remove the upper column cover (two retaining tabs and two hooks). UPPER COLUMN COVER 2 RETAINING TABS 2 HOOKS STEERING WHEEL UPPER COLUMN COVER LOCK QA00805BX PLASTIC TRIM TOOL QA00804AX 17. Turn the steering wheel 180° counterclockwise. Using a plastic trim tool, release the lock as shown. 19. Remove one self-tapping screw from the lower column cover. STEERING WHEEL UPPER COLUMN COVER LOCK STEERING WHEEL SELF-TAPPING SCREW PLASTIC TRIM TOOL LOWER COLUMN COVER QA00807BX QA00803BX © 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 48865 (1303) 7 of 25 20. Turn the steering wheel 180° clockwise, and remove the other self-tapping screw from the lower column cover. 23. Using a felt-tip pen, mark the instrument panel at the measurements shown. INSTRUMENT PANEL SELF-TAPPING SCREW MARK LOWER COLUMN COVER QA00806BX 21. Remove the lower column cover (one self-tapping screw). Equal. Equal. FELT-TIP PEN QB20802AK 24. Using a pushpin, pierce the mark on the instrument panel. INSTRUMENT PANEL LOWER COLUMN COVER QA00808AX SELF-TAPPING SCREW 22. Press the engine start/stop button to select the OFF mode. Disconnect the negative cable from the battery. MARK PUSHPIN QB20803AK 8 of 25 BII 48865 (1303) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 25. While wearing eye protection, drill the pierced mark with a 3 mm drill bit, then enlarge the hole with a 6 mm drill bit. Remove any burrs. To prevent drilling through the inner panel, wrap tape around the drill bit 10 mm (0.4 in.) away from the tip or use a drill stop. 27. Starting near the antenna end of the cable, wrap two urethane tapes around the antenna cable at the measurements shown. ANTENNA CABLE URETHANE TAPES ANTENNA INSTRUMENT PANEL PIERCED MARK 220 mm (8.7 in.) 50 mm (2.0 in.) 540 mm (21.2 in.) 10 mm (0.4 in.) ANTENNA CABLE TAPE DRILL 3 mm 6 mm DRILL BIT QB20804AK Installing the Antenna 26. Using scissors, cut one urethane tape in half. Wrap two halves of urethane tape to the antenna cable as shown. ANTENNA 2 URETHANE TAPES (Cut in half.) 4 HALVES OF URETHANE TAPE QB20805DK 28. Using scissors, cut two urethane tapes in half. Wrap four halves of urethane tape around the antenna cable at the measurements shown. 29. Attach the antenna. • 60 mm (2.4 in.) 60 mm (2.4 in.) Attach masking tape to the windshield at the measurement shown. HEADLINER MASKING TAPE ANTENNA CABLE 25 mm (1.0 in.) URETHANE TAPE (Cut in half.) HALVES OF URETHANE TAPE QB62501BK (Do not fold the antenna cable.) QB20901DK © 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 48865 (1303) 9 of 25 • Fold back the adhesive backing from the antenna as shown. • Carefully remove the adhesive backing from the antenna, and attach the antenna to the windshield. Press and hold the antenna firmly in place for 30 seconds. • Remove the masking tape. ADHESIVE BACKING ANTENNA ANTENNA QB51401CH • Using isopropyl alcohol on a shop towel, clean the windshield where the antenna will attach. • Attach the antenna with masking tape. Adjust the position of the antenna so there is equal spacing on both sides. ADHESIVE BACKING (Remove.) MASKING TAPE (Remove.) QB51405CH 30. Gently pull down the headliner, and tuck the antenna cable under the headliner. Be careful not to crease the headliner. Clean with isopropyl alcohol. ANTENNA HEADLINER HEADLINER Equal spacing on both sides. ANTENNA MASKING TAPE ANTENNA ANTENNA CABLE QB51404CH QB20902CK 10 of 25 BII 48865 (1303) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 31. Route the antenna cable down the A-pillar as shown. Using four wire ties, secure the antenna cable to the vehicle harness. 33. Using one wire tie, secure the antenna cable to the vehicle harness. ANTENNA CABLE 4 WIRE TIES VEHICLE HARNESS VEHICLE HARNESS WIRE TIE ANTENNA CABLE QB21302AK QB20903BK 32. Pull away the door opening seal. Route the antenna cable down next to the instrument panel, and tuck the antenna cable between the driver’s A-pillar and the instrument panel. Reinstall the door opening seal. DRIVER’S A-PILLAR DOOR OPENING SEAL (Pull away.) INSTRUMENT PANEL ANTENNA CABLE QB21301CK © 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 48865 (1303) 11 of 25 Routing the Engine Starter Harness 34. Route the engine starter harness as shown. Attach the clip on the engine starter harness to the vehicle frame. VEHICLE FRAME 35. Using scissors, cut one urethane tape to the measurements shown. Wrap the cut urethane tape around the engine starter harness 5-pin connector. VIEW FROM URETHANE SIDE 20 mm (0.8 in.) CLIP ON THE ENGINE STARTER HARNESS ENGINE STARTER HARNESS 5-PIN CONNECTOR 25 mm (1.0 in.) URETHANE TAPE ENGINE STARTER HARNESS RELAY BLOCKS ENGINE STARTER HARNESS 12 of 25 ENGINE STARTER HARNESS QB21402AK QB21401AK BII 48865 (1303) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 36. Unplug the vehicle 5-pin connector from the fuse box. Plug the engine starter harness 5-pin connector into the fuse box 5-pin connector. Plug the vehicle 5-pin connector into the engine starter harness 5-pin connector. NOTE: Make sure the engine starter harness 5-pin connector is securely connected to the fuse box 5pin connector. A loose connection can cause the engine to stall. Connector unlock 2 Pull. 1 Push. 37. Plug the engine starter harness 4-pin connector into the fuse box. 4-PIN CONNECTOR FUSE BOX Connector lock 2 Push. 3 Unplug. 1 Plug. FUSE BOX ENGINE STARTER HARNESS 4-PIN CONNECTOR VEHICLE 5-PIN CONNECTOR QB21404AK ENGINE STARTER HARNESS 5-PIN CONNECTORS QB21403AK © 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 48865 (1303) 13 of 25 38. Unplug the vehicle 20-pin connector, and plug it into the engine starter harness 20-pin connector. Plug the engine starter harness 20-pin connector into the vehicle 20-pin connector. 39. Attach the engine starter harness 20-pin connector to the vehicle connector as shown. VEHICLE CONNECTOR FUSE BOX FUSE BOX VEHICLE 20-PIN CONNECTOR VEHICLE CONNECTOR ENGINE STARTER HARNESS 20-PIN CONNECTOR QB21502AK 40. Using one long wire tie, secure the engine starter harness 5-pin connector and antenna cable to the vehicle harness. ENGINE STARTER HARNESS 5-PIN CONNECTOR VEHICLE HARNESS ENGINE STARTER HARNESS 20-PIN CONNECTORS VEHICLE 20-PIN CONNECTOR VEHICLE HARNESS LONG WIRE TIE QB21501BK WIRE TIE ANTENNA CABLE QB21601AK 41. Using one wire tie, secure the engine starter harness and antenna cable to the vehicle harness. 14 of 25 BII 48865 (1303) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 42. Using two wire ties, secure the engine starter harness to the vehicle harness. 45. Secure the engine starter harness and antenna cable to the drilled hole in the instrument panel with one wire tie at the white tape on the engine starter harness. DRILLED HOLE WHITE TAPE ON ENGINE STARTER HARNESS WIRE TIE 2 WIRE TIES INSTRUMENT PANEL ENGINE STARTER HARNESS VEHICLE HARNESS QB21602AK 43. Using one long wire tie, secure the engine starter harness and antenna cable to the vehicle frame. LONG WIRE TIE ANTENNA CABLE VEHICLE FRAME ENGINE STARTER HARNESS ANTENNA CABLE FRONT ENGINE STARTER HARNESS QB21701CK LONG WIRE TIE INSTRUMENT PANEL WIRE TIE QB21603BK 44. Using one wire tie, secure the engine starter harness and antenna cable to the vehicle harness. © 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 48865 (1303) 15 of 25 46. Unplug the vehicle 32-pin connector from the vehicle unit, and plug it into the engine starter harness 32-pin connector. Plug the engine starter harness 32-pin connector into the vehicle unit. 47. Using isopropyl alcohol on a shop towel, clean the areas where the fuse labels will attach. 40A FUSE LABEL 3A FUSE LABEL Clean with isopropyl alcohol. ENGINE STARTER HARNESS RELAY BLOCK QB22201AK VEHICLE 32-PIN CONNECTOR 48. Attach one 40A fuse label and one 3A fuse label to the engine starter harness relay block. 49. Install three relays to the engine starter harness relay blocks. 3 RELAYS VEHICLE UNIT ENGINE STARTER HARNESS 32-PIN CONNECTORS QB21702BK ENGINE STARTER HARNESS RELAY BLOCKS QB22202AK 16 of 25 BII 48865 (1303) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 50. Using isopropyl alcohol on a shop towel, clean the area where the urethane tape will attach. 53. Install the control unit bracket to the control unit. CONTROL UNIT BRACKET Clean with isopropyl alcohol. CONTROL UNIT URETHANE TAPE 100 mm (3.9 in.) VEHICLE FRAME URETHANE TAPE (Cut.) QB22205AK QB22203AK 51. Using scissors, cut one urethane tape to the measurements shown. Attach the cut urethane tape to the vehicle frame. 54. Near the brake padel, remove the vehicle nut from the vehicle frame, and secure the control unit bracket to the vehicle frame with the vehicle nut. 52. Plug the antenna cable connector and engine starter harness 28-pin connector into the control unit. VEHICLE FRAME VEHICLE NUT (reused) CONTROL UNIT CONTROL UNIT BRACKET ENGINE STARTER HARNESS 28-PIN CONNECTOR ANTENNA CABLE CONNECTOR © 2013 American Honda Motor Co., Inc. – All Rights Reserved. CONTROL UNIT BRACKET QB22204BK BII 48865 (1303) QB22301BK 17 of 25 55. Attach the engine starter harness relay block to the control unit bracket. 58. Align the white tape on the engine starter harness with the clip on the vehicle harness, and secure the engine starter harness to the vehicle harness using one wire tie. ENGINE STARTER HARNESS RELAY BLOCK VEHICLE HARNESS WIRE TIE CLIP ON THE VEHICLE HARNESS WHITE TAPE CONTROL UNIT BRACKET QB22302AK WIRE TIE 56. Bundle up the excess antenna cable as shown. ENGINE STARTER HARNESS VEHICLE HARNESS QB22304AK 59. Using one wire tie, secure the engine starter harness to the vehicle harness. 100 mm (3.9 in.) 20 mm (0.8 in.) or above. ENGINE STARTER HARNESS 32-PIN ANTENNA CONNECTOR CABLE LONG WIRE TIE QB22303CK 57. Using one long wire tie, secure the antenna cable and engine starter harness 32-pin connector to the vehicle harness. 18 of 25 BII 48865 (1303) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 60. Unplug the vehicle 12-pin connector, and plug it into the engine starter harness 12-pin connector. Plug the remaining engine starter harness 12-pin connector into the combination light switch. 61. Using two wire ties, secure the engine starter harness to the vehicle harness. COMBINATION LIGHT SWITCH Do not tighten the 12-pin connector wire tie too tight. ENGINE STARTER HARNESS 12-PIN CONNECTOR ENGINE STARTER HARNESS VEHICLE HARNESS ENGINE STARTER HARNESS 2 WIRE TIES QB22401BK VEHICLE 12-PIN CONNECTOR ENGINE STARTER HARNESS 12-PIN CONNECTOR © 2013 American Honda Motor Co., Inc. – All Rights Reserved. QB22305BK BII 48865 (1303) 19 of 25 62. Unplug the vehicle 10-pin connector, and plug it into the engine starter harness 10-pin connector. Plug the remaining engine starter harness 10-pin connector into the wiper switch. 63. Using one wire tie, secure the engine starter harness to the vehicle harness. NOTE: Make sure that the connectors and harness are not pinched, or are not interfering with the steering wheel when it is moved for adjustment. Do not tighten the 10-pin connector wire too tight. ENGINE STARTER HARNESS 10-PIN CONNECTOR ENGINE STARTER HARNESS WIRE TIE VEHICLE 10-PIN CONNECTOR VEHICLE HARNESS QB22801BK ENGINE STARTER HARNESS 10-PIN CONNECTOR WIPER SWITCH 64. Using isopropyl alcohol on a shop towel, clean the area where one urethane tape will attach. QB22402BK URETHANE TAPE Clean with isopropyl alcohol. LOWER COLUMN COVER QB22802AK 65. Attach the urethane tape to the lower column cover in the area as shown. 20 of 25 BII 48865 (1303) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 66. Using isopropyl alcohol on a shop towel, clean the hood where the caution label will attach. REMOTE ENGINE STARTER REGISTRATION 1. Acquire the PCM Code from the Interactive Network. Clean with isopropyl alcohol. CAR ICON CAUTION LABEL QB70450AH QB22803BK 67. Attach the caution label to the hood in the area shown. 68. Check that all wire harnesses are routed properly and all connectors are plugged in. 2. Connect the HDS/MVCI tester to the OBD II data link connector, then turn the ignition switch to the on (II) position. 3. Start the HDS, and click the car icon. 4. Input the VIN and other required information into the HDS, then click the check button. 69. Check the overlap between the headliner and the driver’s A-pillar trim. Refer to the service manual. If necessary, adjust the overlap. 70. Reinstall all removed parts. 71. Reconnect the negative cable to the battery. 72. Press and hold the radio power button for two seconds to restore the radio and navi (if equipped) system functions. 73. Reset the clock. 74. Perform the “REMOTE ENGINE STARTER REGISTRATION” and the “FUNCTION CHECK”. Input the VIN and other required information. CHECK BUTTON QB32102BH © 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 48865 (1303) 21 of 25 5. Select Honda Systems, then click the check button. 7. Select “Honda Systems.” Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT, then click the check button. Select “REGISTER REMOTE CONTROL ENGINE STARTER UNIT.” CHECK BUTTON CHECK BUTTON QB32103AH QB32105BH 6. Select R/C ENG STARTER and click the check button. 8. Select “R/C ENG STARTER.” The following message will display: Obtain PCMcode (IMMOBILIZER PCM CODE) from iN. This vehicle’s VIN will be required to obtain the password. (USA) Click the check button. “Obtain PCM-code” message. CHECK BUTTON QB32104AH CHECK BUTTON QB32106AH 22 of 25 BII 48865 (1303) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 9. Input the PCM-code, then click the check button. NOTE: To ensure security, the PCM-code (password) is changed everyday, so it is impossible to register the remote control engine starter if the dates of the PCM-code acquisition and registration are different. The date of the HDS/MVCI tester should also be the same. 11. The following message will display: Check that engine can be started by the Transmitter. Click the check button. “Check that engine can be started by the Transmitter.” Input the PCM-Code. CHECK BUTTON CHECK BUTTON QB32109CH 12. Perform the FUNCTION CHECK on page 24, then disconnect the HDS/MVCI. QB32107BH 10. The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Turn the ignition switch off. “The registration of the Remote Control Engine Starter Unit has been completed.” QB32108CH © 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 48865 (1303) 23 of 25 FUNCTION CHECK Operating Conditions • The hood is closed • The shift lever is in park • Turn the ignition switch off and the key is outside the vehicle • All doors and tailgate closed and locked Inspection 1. Press the engine/command button on the transmitter, and release, within 2 seconds, press the lock/start button on the transmitter. The engine should start if all operating conditions are met. Does the engine start? Yes - Operation is normal. No: • Make sure all “Operating Conditions” are met. • Check the engine starter harness connections. • Connect the HDS/MVCI and check for an indicated failure. (Refer to the appropriate Service Manual for details.) 2. ENGINE START OPERATION Press the engine/command button on the transmitter and release, within 2 seconds, press the unlock/stop button. The engine should stop. CHECKING INDICATOR Does the engine stop? Yes - Operation is normal. After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions: NOTE: After each test the ignition key must be cycled, or the driver’s door must be opened and closed. • Move the shift lever out of the P position. • Unlock or open the doors or the tailgate. • Open the hood. • Press on the brake pedal. • Press the engine start/stop button. Blinking ENGINE/ COMMAND BUTTON No - Check the engine starter harness connections. 3. RECEPTION INDICATOR ENGINE RUNNING INDICATOR UNLOCK/ STOP BUTTON *1 REMAINING IDLING TIME LOCK/ START BUTTON IN-CAR B127121H TEMPERATURE*1 *1 Only on vehicles equipped with the automatic climate control. This indicator is displayed for some vehicles among them. Does the engine stop after each of these tests? Yes - Operation is normal. No - Check the engine starter harness connections. 4. Check that the power windows and the moonroof do not function, and the shift lever does not move to any position when the engine is started with the transmitter. 5. Check that the engine does not start under “Operating Conditions” with the key left inside the vehicle. 6. Start the engine again, press the engine/command button on the transmitter two times, and check the vehicle condition on the display. 7. Check the operation of the transmitter when the vehicle is 120 m (400 ft.) away and in direct sight. 24 of 25 BII 48865 (1303) © 2013 American Honda Motor Co., Inc. – All Rights Reserved. 8. Press the unlock/stop button on the transmitter and verify that the doors unlock. Press the lock/start button, and verify that the doors lock. • 9. For the vehicle equipped with the memory seat, make sure to shift the seat position of driver’s seat to “Driver 1” by unlock of transmitter. Check that the engine can start by the vehicle key and that the wiper and the headlight can be operated normally. © 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 48865 (1303) 25 of 25