Download Detection Systems DS7060 Specifications

Table of Contents
Keypad Quick Reference Guide
1
1.0 Specifications
4
1.1 Enclosure Housing
1.2 Temperature
1.3 Power
1.4 Outputs
1.5 Zones
1.6 Keypads
1.7 Communicator
1.8 Partitions
1.9 Users
1.10 Lightning Protection
1.11 Burglar/Fire Zone Inputs
1.12 Fire Signal Initiating Circuit (2-wire mode)
1.13 Multiplex Bus Wiring Requirements
1.14 Option Bus Wiring Requirements
1.15 Max. Load Currents
1.16 Backup Battery Calculation
1.17 Standby Current Load
1.18 Options
2.0 Enclosure Installation
2.1 Install the Enclosure
2.2 Install the Control/Communicator
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5
21
8.1.1 General Information
8.1.2 Removing a PIN
8.1.3 Authority Levels
21
21
21
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
8.9.1
8.9.2
8.9.3
8.9.4
8.9.5
8.9.6
8.11 Emergency Keypad Alarms
8.12 Fire Safety
8.12.1 If Installed in Family Residences
8.12.2 Having and Practicing an Escape Plan
8.12.3 Installation Considerations
8.13 Testing
8.13.1 Zone Test
8.13.2 Battery/Sounder Test
8.13.3 Communicator Test
8.13.4 Event History Readback
8.13.5 Remote Program Dial-out and Answer
8.13.6 Error Displays
14
14
14
14
14
14
14
14
14
14
7.0 Glossary
14
7.1 General Control Programming
7.2 Zone Function Programming
7.3 Zone Programming
7.4 Output Programming
7.5 Partition Control Programming
7.6 Keypad Assignment Programming
7.7 Emergency Key Programming
7.8 Custom Arming Programming
7.9 Force Arming
7.10 Ground Fault Detect Programming
7.11 Commercial Fire Mode Programming
7.12 Open/Close Report Control Programming
7.13 Report Programming
Identifying Alarm Sounds
Silencing Alarms
A Cautionary Note
Use Common Sense
Caution When Entering A Building
Fire Alarms
22
22
22
23
23
24
25
25
25
25
25
25
25
25
25
25
14
6.2 Zone
6.3 Zone Function
Arming/Disarming Commands
Changing the Date
Changing the Tempoary PIN Expiration Date
Changing the Time
Delayed Arming
Automatic Arming
Turning OFF the System under Duress
Emergency Procedures
7
7
10
A/C Failure Report Delay
Entry/Exit Delay Cancel Zone Functions
General “Arm-Only” Authority by Partition
Input/Output Cross Matrixing
Multiplex Bus Outputs
Octal Relay Modules (DS7488)
Output Functions
DS7400Xi Ver. 3+ Reference Guide
8.1 Personal Identification Numbers
25
9
6.1 DS7400Xi Description
21
8.10.1 Fire Reset
8.10.2 Fire Trouble
4.0 Hardware Layout Example
6.1.1
6.1.2
6.1.3
6.1.4
6.1.5
6.1.6
6.1.7
8.0 Operating Guide
19
19
19
19
20
20
8.10 Fire Reset/Fire Trouble
8
6.0 System Overview
Phone Number General Control Programming
Phone Answering Programming
FCC Compliance Notice
FCC Phone Connection Notice To Users
Canadian Dept. of Communications
For Installations in New Zealand
7
3.0 Control Terminal Wiring
5.0 System Worksheet
7.14
7.15
7.16
7.17
7.18
7.19
14
15
16
16
17
17
17
17
17
17
17
18
18
9.0 The Master Keypad
9.1 Master Keypad Displays
9.2 Arming from the Master Keypad
9.3 Disarming from the Master Keypad
9.4 Single Partition Mode
10.0 How to Program the Control Panel
10.1
10.2
10.3
10.4
10.5
10.6
10.7
Entering the Programmer’s Mode
Reading back a Program Address
Entering a value in a Program Address
HEX values
Defaults
Setting the Control to the Factory Default
Exiting the Programmer’s Mode
26
26
26
26
27
27
27
27
28
28
28
29
30
30
30
31
31
31
31
31
31
32
32
32
32
11.0 Understanding the Programming Charts
32
12.0 Programming
34
12.1 General Control Programmong: Program Address
(0000)
34
Copyright © 1995-96 Detection Systems, Inc.
Page 2