Download Sharp R-340M W Operating instructions

—2—
11⁄4"
1"
14 1⁄2"
TYP
24 1⁄2"
5⁄16"
1⁄2-IN.
26 15⁄16" TYP
23 1⁄4" TYP
SIDE INLET
SIDE INLET
DIA THERMOSTAT
ENTRY
22 11⁄16"
2-IN. VENT CONN
DIA
GAS CONN
1⁄2-IN.
2-IN. COMBUSTIONAIR CONN
22
26 15⁄16"
26 1⁄4"
UNIT SIZE
024040
036040
024060
036060
048060
036080
048080
060080
048100
060100
060120
CONDENSATE
DRAIN LOCATION
(UPFLOW)
9 7⁄16"
TYP
E
INLET
OUTLET
D
11/16"
D
15-7/8
15-7/8
15-7/8
15-7/8
15-7/8
15-7/8
15-7/8
19-3/8
19-3/8
19-3/8
22-7/8
Fig. 2—Dimensional Drawing
A
17-1/2
17-1/2
17-1/2
17-1/2
17-1/2
17-1/2
17-1/2
21
21
21
24-1/2
DIMENSIONS (IN.)
18 1⁄4"
TYP
9⁄16"
DIMPLE LOCATORS
FOR HORIZONTAL
HANGING
CONDENSATE
DRAIN LOCATION
(UPFLOW)
30
1⁄2"
CONDENSATE DRAIN
TRAP LOCATION
(DOWNFLOW &
HORIZONTAL RIGHT)
OR ALTERNATE
1⁄2-IN. DIA GAS CONN
13/16"
NOTES: Minimum return-air opening at furnace:
1. For 800 CFM--16-In. round or 14 1/2 x 12-In. rectangle.
2. For 1200 CFM--20-In. round or 14 1/2 x 19 1/2-In. rectangle.
3. For 1600 CFM--22-In. round or 14 1/2 x 23 1/4-In. rectangle.
4. For airflow requirements above 1800 CFM, use both side inlets, a
combination of 1 side inlet and the bottom, or the bottom only.
11/16"
33 1⁄4"
TYP
5
32 ⁄8"
TYP
30 13⁄16"
29 11⁄16"
TYP
27 5⁄8"
27 9⁄16"
TYP
24 1⁄2"
17 5⁄16"
CONDENSATE
DRAIN TRAP
LOCATION
(ALTERNATE
UPFLOW)
DIA
ACCESSORY
POWER ENTRY
7⁄8-IN.
DIA
POWER CONN
7⁄8-IN.
CONDENSATE DRAIN
TRAP LOCATION
(DOWNFLOW &
HORIZONTAL LEFT)
13/16"
A
AIRFLOW
E
16
16
16
16
16
16
16
19-1/2
19-1/2
19-1/2
23
24 3⁄16"
BOTTOM INLET
22 1⁄4" TYP
SIDE INLET
22 11⁄16"
2-IN. VENT CONN
DIA
THERMOSTAT ENTRY
1⁄2-IN.
DIA
POWER CONN
7⁄8-IN.
DIA
GAS CONN
1⁄2-IN.
2-IN. COMBUSTIONAIR CONN
OUTLET
19"
22 5⁄16"
26 1⁄4"
28 1⁄2"
26 15⁄16"
A93023
11⁄16"
7⁄16"
1"
39 7⁄8"
5⁄16"
5⁄8"
13⁄16"