Download AudioBahn A1801Q Specifications

Transcript
Table
of Contents
.-~.~--_.~.
her.. .
INTRODUCTION
FEATURES
AND SPECIFICATIONS
CONTROLS
AND FUNCTIONS
.................................................................................
.....................................................................................
A2201Q/A2301Q/A2401Q/A2601Q/A2801QIA3201Q
A44OlQ/A46OlQ
.........................................................
...5
.
...................................................................................................................
A1801Q ................................................................................................................................
.
I MOUNTING
YOUR SYSTEM
...................................................................
.....................................................................................................
DIAGRAMS
A1801Q ............................................................................................................................
A2201Q/A2301Q/A2401Q/A2601QIA2801Q/A3201Q
A4401Q/A4601Q
...................................................
.......................................................................................................
A66OlQ .......................................................................................................................
ADJUSTMENTS
TROUBLE
AND TUNING
SHOOTING
WARNING/DISCLAIMER
WARRANTY
bc.com
5-14
.
WIRING
ducts
,4
A6601Q ................................................................................................................................
PLANNING
25
3
....................................................................................................................
........................................................................................
,151
.16-22
...16
..16- 1 7
...18-19
..20-2 2
23
.......................................................................................................
,24
...................................................................................................
,25
..........................................................................................................................
26
at.. .
2
Features
.‘ “““. and Specificatioln
e Class A/B Mosfet Power Amplifier
e 2 Ohm Stable Stereo
Q 4 Ohm Stable Mono
e Full Mosfet Power Supply
@ Non Regulated Power Supply
@ Double Sided Circuit Board
0 Interior Circuit Board llluminatior
e Blue LEDVolt Meter*
0 Fan Cooled
* 18dB Bass Boost
l
Soft Start Circuitry
l
Variable Sub Sonic Filter 20-50H.
* Signal To Noise Ratio: 1OOdB
* High Quality Bipolar Audio Stagt
Introduction
”----. “.--“- .----.“-.“. ^..- ----
--I
”
.
Thank you for purchasing an Audiobahn A/B Power Amplifier
specifically designed for the mobile environment. This manual contains
important information about installation, set-up procedures and intergrading
this amplifier into your car stereo system. With proper care and installation,
your new audiobahn A/B Mosfet Power amplifier will provide you with
many years of high performance listening enjoyment.
Before making any electrical connections, Make sure that vou disconnect the
battery’s ground cable to prevent the possibility of short &wits or damage to
your electronic equipment. (rJ’your stereo has an Anti-th# code DO NOT
disconnect the battery).
Recommended Fuse Size
.
*
*
*
e
.
*
A2201Q
A2301Q
A2401Q
A2601Q
A2801Q
A3201Q
A4401Q
l
A4601Q
* A6601Q
@ A1801Q
2OAx 1
25Ax 1
30Ax 1
20Ax2
30Ax2
4OAx2
30Ax 1
2OAx2
3OAx2
2OAx2
Power “.._”
Output
.,^-x_I.
. A2201Q
. A2301Q
l
A2401Q
. A2601Q
. A2801Q
. A3201Q
. A4401Q
. A4601Q
e A6601Q
l
A1801Q
3
-_
50 watts x 2 @ 4 ohm
75 watts x 2 @ 4 ohm
lOOwattsx2@4ohr
150 watts x 2 @ 4 ohr
200 watts x 2 @ 4 ohr
300 watts x 2 @ 4 ohr
50wattsx4@4ohm
75wattsx4@4ohm
75wattsx6@4ohm
400 watts x 1 @ 4 ohr
B Class A/B Mosfet Power Amplifier
e 2 Ohm Stable Stereo
e 4 Ohm Stable Mono
0 Full Mosfet Power Supply
@ Non Regulated Power Supply
e Double Sided Circuit Board
0 Interior Circuit Board Illumination
0 Blue LED Volt Meter*
0 Fan Cooled
0 18dB Bass Boost
l
Soft Start Circuitry
l
Variable Sub Sonic Filter 20-5OHz**
l
Signal To Noise Ratio: 1OOdB
e High Quality Bipolar Audio Stage
-_l_ll_,_^,~-_---l--.-_ll.“...l-^l~
n A/B Power Amplifier
ment. This manual contains
-up procedures and intergrading
5th proper care and installation,
Wier will provide you with
Ijoyment.
fake sure that vou disconnect the
ility qf shovt c&cuits or damage to
7s an Anti-th$ code DO MOT
.
.
0
.
*
*
e
*
0
*
A2201 Q : 20A x 1
A2301 Q : 25A x 1
A2401Q: 3OAx 1
A26OlQ:
2OAx2
A28OlQ:3OAx2
A3201Q: 4OAx 2
A44OlQ:
3OAx 1
A46OlQ:2OAx2
A66OlQ:3OAx2
Al8OlQ:
2OAx2
Power “..^
~~~~~~
.
. A2201 Q : 50 watts x 2 @ 4 ohms
l
A2301 Q : 75 watts x 2 @ 4 ohms
l
A24OlQ:
lOOwattsx2@4ohms
l
A26OlQ:
15Owattsx2@4ohms
l
A2801 Q : 200 watts x 2 @ 4 ohms
l
A3201 Q : 300 watts x 2 @ 4 ohms
l
A44OlQ:5Owattsx4@4ohms
l
A4601 Q : 75 watts x 4 @ 4 ohms
o A6601 Q : 75 watts x 6 @ 4 ohms
o Al 801 Q : 400 watts x 1 @ 4 ohms
.
.
.
.
.
.
A22OlQ
A2301 Q
A2401 Q
A2601 Q
A28OlQ
A32OlQ
l
A4401 Q
. A4601 Q
. A66OlQ
l
A18OlQ:
:
:
:
:
:
:
:
:
:
2.2” (H) x 12.7” (W) x
2.2” (H) x 12.7” (W) x
2.2” (H) x 12.7” (WI x
2.2” (H) x 12.7” (WI x
2.2” (H) x 12.7” [WI x
2.2” (H) x 12.7” (WI x
2.2” (H) x 12.7” (W) x
2.2” (H) x 12.7” (W) x
2.2” (H) x 12.7” (w) x
2.2”(H)x12.7”(W)x
~
8” (D)
8.8” (D)
lo” (D)
11.6” (D)
15.1” (D)
17.1” (D)
11.2” (D)
12.6” (D)
17.1” (D)
15.1”(D)
.
5
0
0
0
0
0
0
8
0
Controls and Functions
-~-
0
0
-7
3
_- _-.--
li
0
0
0
0
0
x
8
0
1c!
f
0
0
Q
Controls and Functions
[I,f
;::I
A4401 Q/A4601 Q REAR
A4401 WA4601 Q FRONT
ah 8
7
9
-
(
Controls and Functions
___
_.~-~~~-. _.
Controls
and Functions
.I-XIIII1...l
“__^~.”
Controls
_..------. and Functions
I” I. ,_
_
Controls and Functions ___..._
“- ..-.~-“---.--....--. - ~..~.
_
.-.
e
,-.-.
-.
Controls
_. Functions
_- ” .._-.and
.- _._-----~
___
-8
I_____________--___________________
These inputs are for signal cables frm
cables.
A4401Q
A4601Q
j
:
I__________________________________
The LINE OUT allows you to build multipll
to distribute the signal. Now it is simple 1
amplifier, then using the line out RCA ja
_ _ _ _ _’,
;-------------.---------.------------------------------~--------------~~~-
.____________.._________________________~--~-----------------------------~-----.
A1801Q
;
-~---...............--~---~------By using the bass boost function, bass nm
x-c
GAIN
CONTROL
0@
GN
&
-------------~----------~--------------~----------.-.-----------~----------.--~
A2201 Q / A2301 Q
A2401 Q / A2601 Q
A2801Q/A3201Q
A4401Q/A4601Q:
A6601 Q / Al 801 Q
I
This control adjusts the amplifiers input sensitivity. Input sensitivity is variable from 200 Millivolts
to 7 volts. Clockwise increases sensitivity Counterclockwise decreases sensitivity.
This knob is not a volume control for the amplifier. The amplifier can be driven to full power
with a wide range of signal levels. A lower signal level will require increased sensitivity for full
power. A higher signal level will require decreased sensitivity.
9
FULL
i
:
a
-$j
___--.
.___-- _-.,__-______
Adjust the crossover for your chosen ins
- LPF : Low pass filter-only bass tones (i
Use with woofer or sub-woofer.
- FULL: No filter-all tones go to speaker!
- HPF : High pass filter-blocks very low 1
from the speakers.
Controls _,-_.
and Functions
l~-,ll”.“”
_
._I”.
--”
--_.... . “l_-.
-
1...................---~---~-------------------------~-------~------~----~-----,
These inputs are for signal cables
cables.
I
A4401Q
A4601Q
____________________-------------~
from the source. Always use high quality shielded RCA
LINE OUT
LINE OUT
LEFT
CHI
j
:
A4401Q i
A1801Q :
A46018 :
HGHT
CM
I_________._____________________________I_____________-___-_____-____--_----.---,
The LINE OUT allows you to build multiple amplifier systems without having to use splitter cords
to distribute the signal. Now it is simple a matter of bringing one set of RCAS into the first
amplifier, then using the line out RCA jacks as the feed to the next amplifier.
BASS
BOOST $a~
A1801Q
._________________________________
!
BASS
BOOST
BASS
BOOST
;
_________-______-_______________
_,
By using the bass boost function, bass notes at 50 Hz are emphasized as much as 18dB.
‘-Fan--*------------,---------------*------------------
X-OVER A2201Qi
X-OVER
i
X-OVER
X-OVER
i
-”
A2201Q/A2301Q
i
A2401Q/A2601Q:
A2801QIA3201Q
0
A4401Q/A4601Q:
A6601Q/A1801Q;
._____________--___----~.--~-----.rt sensitivity is variable from 200 Millivolts
:kwise decreases sensitivity.
! amplifier can be driven to full power
,I will require increased ~~nsitivi~ for full
tnsitivity.
________________________________________-----------------------------.--.-----~
Adjust the crossover for your chosen installation method.
- LPF : Low pass filter-only bass tones (50Hz-120Hz/50Hz-500Hz:A6601 Q) go to speakers.
Use with woofer or sub-woofer.
- FULL : No filter-all tones go to speakers. Use with full-range speakers, or with external crossovers.
- HPF : High pass filter-blocks very low tones (50Hz-750Hz/50Hz-500Hz:A6601 Q)
from the speakers.
10
Controls and~..---..,_
Functions
-_.-
.._.
.
.~
Controls and -_-_--Functions-^
^-
.
.
FI
POWER
,--.
A2201Q
;
E%
A2601Q
A2801’d
-pm&
:
;
s
:
;,ggg
A1801Q
:
:
A2201Q
j
________________________________________----------~---~----~~~-----~---~-----~~
To avoid unwanted ignition noise caused by ground loops, it is essential that the Amplifier
be grounded to a clean, bare, metal surface of the vehicles chassis.
I__________________________________
Variable Low-Pass Filter (50Hz-‘I 2OHz) :
filter switch to “LPF”. Adjust variable cr(
The amplifier input circuit filters out ev
adjustment of the frequency control),
Note: GROUND WIRE SHOULD NOT BE EXTENDEDMORE THAN 3 FT (1 METER].
POWER
GND
,--_
REM /‘BATI
‘\
5(
__--__-___-___-_________________
.___________________--.-----------------------------------~~-----------~---~---,
Due to the power requirements of the Amplifier, this connection should be made directly
to the positive (+)terminal of battery. For safety measure, install an in-line fuse Holder
(not included)as close to the battery positive (+) terminal as possible with an ampere
rating ; not to exceed total value of fuses in Amp.
Variable Low-Pass Filter (50Hz500Hz) :
filter switch to “LPF”. Adjust variable crt
The amplifier input circuit filters out ev
adjustment of the frequency control),
POWER
,--w
REM
51
‘WD
____________________--------------
Variable High-Pass Filter (50Hz-750Hz)
channel, set filter switch to “HPF”. The
below 50Hz . .. .. . . 750Hz.
I_______________________________________------------------~~---~---~-
To remote wire car stereo.
This amplifier is turned “ON” remotely when vehicle’s stereo is turned “ON”
Note:
IF YOUR RADIO DOES NOT HAVE + 12 VOLT OUTPUTLEAD WHEN THERALXO IS TURNEDON,
THE ‘REMOTE” TERMINAL ON THEAMPLIFIER CAN BE CONNECTED JO VEHICLESACCESSORY
C/RCU/T THATIS LIVE WHEN THEKEYIS “ON”.
._____________________________
Sub Sonic Switch : ON and OFF
Sub Sonic Variable : 20Hz-50Hz
11
Controls and Functions
________________________________________-----------LPF
FREQUENCY
A2201
A2401
A2801
A4401
Q/A2301
Q/A2601
Q/A3201
Q/;‘WI;
Q
Q
Q
‘GQ
j
;
0
:
,_______________________________________--------------------~---~--------------,
_________.
.___.___________’
_______
loops, it is essential that the Amplifier
vehicles chassis.
Variable Low-Pass Filter (50Hz-‘I 20Hz) : For use as a dedicated subwoofer channel, set
filter switch to “LPF”. Adjust variable crossover frequency with control as desired.
The amplifier input circuit filters out everything above 50Hz . . . . 120Hz (dependent on the
adjustment of the frequency control), so only the deepest bass notes are amplified.
_____-_.___.__--___-.-------------------------------
?E THAN 3 FT [I METER).
LPF
FREQUENCY
,________________________________
A2201Q
\
,
:
0
\
I
\
I
I
I
__________________-_____________1
connection should be made directly
ssure, install an in-line fuse Holder
,minal as possible with an ampere
50:
8
l
500Hz
A6601Q
:
________________________________________----------.-----------------~---------~
Variable Low-Pass Filter (50Hz500Hz) : For use as a dedicated subwoofer channel, set
filter switch to “LPF”. Adjust variable crossover frequency with control as desired.
The amplifier input circuit filters out everything above 50Hz
500Hz (dependent on the
adjustment of the frequency control), so only the deepest bass notes are amplified.
__-_---___-___-___-_____________________-----~--.--HPF
FREQUENCY
A2201 Q/A2301 Q
A2401Q/A2601Q
A2801 Q/A3201 Q
A4401 Q/A4601 Q
1.-...-........-..-.....................--------------------------------------~
i
;
:
a
Variable High-Pass Filter (50Hz-750Hz) : For use as a dedicated mid high range
channel, set filter switch to “HPF”. The input circuit filters out all frequencies
below 50Hz .. . .. .. 750Hz.
__-___________-___-_____________________---r
,________________________________(
j stereo is turned “ON”
FAD WHEN THE/MD/O IS TURNEDON,
ZONNECTED ro VEH/CLESACCESSORY
.________-______________________________------------------------“-----------
Sub Sonic Switch : ON and OFF
Sub Sonic Variable : 20Hz50Hz
SUB SONIC
Controls -x__-,___-,-.
and Functions
.-.
Controls and Functions
I.- ,-.. _.-.._
________________________________________--------~-~------X-OVER
FREQ.
A2:
,
50Hz
5OOHz
A6601Q
i
________________________________________------------~-------------~---~---~----~
Variable X-OVER FREQ(50Hz to 500Hz): For use as a dedicated subwoofer channel, set
filter switch to “X-OVER FREQ.” Adjust variable crossover frequency with control as desired.
The amplifier input circuit filters out everything above 50 . ..500 Hz (dependent on the
adjustment of the frequency control], so only the deepest bass notes are amplified.
I__________________________________
-PWR (Power) : This BLUELED will illumil
illuminate, check the power connec
-PROT ( Protection) : The amplifier prot
overload, short circuit or extremely hi!
protection mode is in operation, the 1
indicating the amplifier has gone into
________________________________________--------------
INPUT
6CH
A6601Q
SWITCHPOSITION
!
INPUTSOURCE
CHl
CH2
CH3
CH4
CH5
CH6
I
,
________________________________________------------------~--~-----------------~
A1801Q
PHASESHIFTSWITCH (0 AND 180 DEGREES):Allows you to change the phase of your
subwoofer from 0 and 180 degrees to help compensate for timing differences between
drivers.
13
‘...
If you observe that the Protection LED
what has caused the protection circa
the remote power off and then on ag
overload condition, please allow it tc
down because of an input overload
before attempting to power up the a
4CH
:
i
!
Controls and Functions
“--~X.“...X-.--.-.X--.“.-.~II....- “._- .I .x---..-
;;g;g i
I
A6601Q
:
,_______________________________I
dedicated subwoofer channel, set
,er frequency with control as desired
e 50 ...500 Hz (dependent on the
repest bass notes are amplified.
A660lQ
._____-___-___-___--_____________
:EI
1
OUTPUT
:
1
A1801Q
i
_________________________________
J to change the phase of your
nsate fer timing differences between
I
<’
0
0
PROT
ymg
:
PWR
A2801Q :
A3201 Q :
yw;QQ
:
PWR PROT
00
A66OlQ
A1801Q :
‘..............-....--------------------~------~-----------.----~--.--~--------.
-PWR (Power) : This BLUELED will illuminate when the amplifier is turned “ON”. If it fails to
illuminate, check the power connections to the Amplifier and fuses.
-PROT ( Protection] : The amplifier protection circuitry will disable the amplifier if input
overload, short circuit or extremely high temperature conditions are detected. When the
protection mode is in operation, the LED indicator on the side panel will be illuminated,
indicating the amplifier has gone into a self-preservation mode.
If you observe that the Protection LED is lit, please check the system carefully to determine
what has caused the protection circuit to engage. The amplifier can be reset by turning
the remote power off and then on again. If the amplifier shut down due to a thermal
overload condition, please allow it to cool down before restarting. If the amplifier shut
down because of an input overload or short circuit, be sure to repair these conditions
before attempting to power up the amplifier again,
;
Planning and Mounting Your System
---” -.----
__I__.
Al8OlQ
ll____l,”
.._
-.-.““-.-
.-
_^
The mounting position of your Amplifier will have a great effect on its ability to dissipate
the heat generated during normal operation.
It has an ample heat sink for heat dissipation, and also designed with a thermal shutdown (for heat protection) circuit. DO NOT enclose the amplifier in a small box or
cover it so that air can not flow freely.
Temperatures in car trunks have been measured as high as (155’ C) in the summer time.
since the thermal shut-down point for the amplifier is (158’ C) it is easy to see that it must
be mounted for maximum cooling capability. To achieve the maximum advantage of
convection air flow in an enclosed trunk, mount the amplifier in a horizontal position.
Cooling requirements are considerably relaxed when mounting inside the passenger
compartment since the driver will not often allow temperatures to reach a critical point.
Floor mounting under the seat is usually satisfactory as long as there is at least 1 inch
of clearance (2.54 cm) above the Amplifier’s fins for ventilation.
A2201Q/A2301Q/A240lQ/A:
~ __.__
---“. .,..”I.. -“___I~___
a. Select a suitable location that is convenient for mounting, is accessible for wiring.
And has ample room for air circulation and cooling.
b. Use the amplifier as a template to mark the mounting holes. Remove the Amplifier
and drill holes. Use extreme caution, inspect underneath surface before drilling!
c. Secure the Amplifier using the screws provided.
LEFT SPEAKE
2-8 OHM
15
-.P
great effect on its ability to dissipate
also designed with a thermal shut?the amplifier in a small box or
s high as (155’ C) in the summer time.
is (158’ C) it is easy to see that it must
thieve the maximum advantage of
e amplifier in a horizontal position,
ten mounting inside the passenger
emperatures to reach a critical point.
y as long as there is at least 1 inch
or ventilation.
2-8 OHM
A2201Q/A2301Q/A2401Q/A2601Q/A2801Q/A3201Q
““llll_ll--- l__l.-__-.. I- .II-- ,----
mounting, is accessible for wiring.
lling.
.rnting holes. Remove the Amplifier
rderneath surface before drilling!
LEFT SPEAKER
2-8 OHM
RIGHT SPEAKER
2-8 OHM
Ix”_~
A1801 Q
“- -..I .._--_-.-,I .“_--, ~~.
great effect on its ability to dissipate
also designed with a thermal shut? the amplifier in a small box or
s high as (155’ C) in the summer time.
is (158’ C) it is easy to see that it must
thieve the maximum advantage of
e amplifier in a horizontal position.
ren mounting inside the passenger
emperatures to reach a critical point.
y as long as there is at least 1 inch
or ventilation.
A2201QlA2301
Q/A2401
Q/A26OlQ/A280l Q/A3201 Q
-~_-_-~-_l_
.- -l-~._.“...~
mounting, is accessible for wiring.
lling.
Jnting holes. Remove the Amplifier
rderneath surface before drilling!
-~~
SUB WOOFER
4-8 OHM
LEFT SPEAKER
2-8 OHM
RIGHT SPEAKER
2-8 OHM
16
-.-..,. ,-
A2201Q/A2301Q/A2401Q/A26OlQlA28OlQXlA320
-.-_ ..--.“_._..“^_. 1Q . . I-, ._“~.
_---_-----___-__________________________----_________________
m--./a
BRIDGED
4-8 OHM
SUB WOOFER
4-8 OHM
0
LEFT 0
LEFT SPEAKER
4-8 OHM
i
+
@----I
8 CHl 0
0 RIGHT 0
RIGHT SPEAKER
4-8 OHM
: INDUCTOR LOW PASSFILTER
:
--I i: CAPACITOR HIGH PASSFILTER
I_________--___-._______________________---.----------.----~---------~------~--,
TRI MODE OPERATIONALOUTPUTallows a Speaker to be operated in MONO mode while the
main speakers are playing in Stereo. Leave the Crossover (Sub-woofer) switch on “Full”
position. Use a 100 Volt, non polar capacitor for a high pass crossover and a wire coil
(inductor) to block high frequencies from the (Sub) Woofer as shown in the figure below.
Capacitor and inductor values as written in the section below determine crossover
frequencies.
COMPONENT
VALUES
FOR 6 dB PASSIVE
FREQUENCY
80 Hz
100 Hz
INDUCTOR
7.5 mH
6.5 mH
150 Hz
Hz
120
5.54mH
mH
CROSSOVER
CHI
2-8
CAPACITOR
470 UF
330 UF
220 UF
UF
330
I
CH3
2-8
17
8OlQXlA3201Q ,”-.,---l_-)(,...
A4401
-------l^-lQ/A4601.. QI.
.
“. ..-.
.1
...I. ..-..-.l..l-.--lllll-~
BRIDGED
4-8 OHM
SUB WOOFER
4-8 OHM
0 0 cm
0
SPEAKER
BRIDGED
~
e
8
e
CH2
________________________________________-~~-------------SUB WOOFER
SPEAKER
3-8 OHM
CH4
8 OHM
CH3
4-8 0
be operated
in MONO mode while the
ssover [Sub-woofer)
switch on “Full”
ligh pass crossover and a wire coil
Noofer as shown in the figure below.
tion below determine
crossover
PASSIVE CROSSOVER
:
:
CH3
2-80HM
/
+
: INDUCTOR LOW PASSFILTER 18
A6601Q
A4401QfA4601Q
CHl
4-8 OHM
4-8
CH2
OHM
CHl
4-8
4-8
OHM
I
I
4-8
OHM
SUB WOOFER
4-8 OHM
CH3 8
SUB WOOFER
4-8 OHM
0
0;
t:
i
+
:
-i
: INDUCTOR LOW PASSFILTER
+
: CAPACITOR HIGH PASSFILTER
:
COMPONENT
1
FREQUENCY
80 Hz
100 Hz
120Hz
150 Hz
VALUES
FOR 6 dB PASSIVE
INDUCTOR
7.5 mH
6.5 mH
5.5 mH
4mH
CHl : 2-8 OHM
CROSSOVER
CAPACITOR
470 UF
330 UF
330 UF
220 UF
CH3
2-8 OHM
____________________-------------.
e
ia
: INDUCTOR LOW PASSFILTER
SPEAKER
0 BRDGED0 CH2
0 CHI 0
4-8
_I
CH2
OHM
4-8
SUB WOOFER
OHM
SUB WOOFER
CHl : 2-8 OHM
PASSiqE
CH2: 2-8 OHM
CkOSSOVER
\ SI
CH3
CH4
2-8 OHM
2-8 OHM
._______________________________________-~---~-------------------------------,
m
: INDUCTOR LOW PASSFILTER
+
t-
: CAPACITOR HIGH PASSFILTER
CHl
CH2
SPEAK
CH3
2-8 OHM
CHl
4-8 OHM
^^...,,~^
Di-tAKeK
1
CH2
A-8
OHM
SUB WOOFER
4-80HM
CH3
4-80HM
CM 8
0
CH4
:
:
CH4
mc
I___________________---~----------.
+
: INDUCTOR LOW PASSFILTER
COMPONENT
SUB WOOFER
4-8 OHM
0 CM 8
0 CH6 8
0 BRIDGED
8
__.___._________________________________-----------------------~----------~----
+
21
: INDUCTOR LOW PASSFILTER
--I
+
: CAPACITOR HIGH PASSFILTER
piy=
120 Hz
150 Hz
VALUES
A64OlQ
__...
“__“-_^ ,;I I
CHl
1.,
“__^._
-.-__.-.~~-.I, “.-..“-l.-
SPEAKER
CH4
4-8 OHM
_ _ _ _ _’,
._______-__------___________
._____-__-_____--_-----~.
CH5: 4-6 OHM
CHG.
A-R
OHM
CH2
3 OHM
SUB WOOFER
4-60HM
i
8
CH4
4-8 OHM
._______________________________________------------.--------------------------,
+
: INDUCTOR LOW PASSFILTER
COMPONENT
AKER
I,
63 CH5 0
d CH6 0
8 __
BRIDGED I,‘~63
_________________________________
--!
I-
: CAPACITOR HIGH PASSFILTER
VALUES
-+
FOR 6 cl6 PASSIVE
: CAPACITOR HIGH PASSFILTER
CROSSOVER
:
Turning on“.-_..
The
Amplifier
- _....._.
.‘_
-.-..-_____
__--_” “‘
“..“..-
The amplifier automatically turns on a few seconds after you turn your vehicle’s ignition
switch to ACC or ON or turn on your auto sound system, depending on how you wired
the system. The POWER indicator on the top of the amplifier lights when the amplifier is on.
Important
Trouble
Shooting
--. I_--.l(-l_il_“---lll^.
1SYMPTOMS
NO SOUND
: Your amplifier requires 30 amps or more of power from your vehicle’s battery
during operation. To protect your battery from discharging, do not operate
the amplifier unless your vehicle is running.
Adjusting The
Level
I - ....Audio
.II-..........-
-
““_._-x
1 CHECU
Is the power
LED illuminatec
(NOI
L
Is the Diagnosti
LED illuminatec
For the best performance, you must set GAIN (MIN/MAX) on the side of the amplifier to
adjust the level of the audio signals that enter the amplifier.
1. Use a screwdriver to turn GAIN (MIN/MAX) fully counterclockwise
to MIN>
2. Turn the auto sound system’s volume control to about one-third of its full range.
3. Adjust GAIN (MIN/MAX) to a comfortable listening level.
4. Turn up the auto sound system’s volume control until the sound begins to distort. Then
immediately turn the volume down to a point just before where the distortion began.
Caution : Never turn up the auto sound system’s volume control more than needed to
adjust the audio level, more than two thirds of its maximum volume.
5. Adjust GAIN (MIN/MAX) until the sound is at the maximum level you want the amplifier
to produce.
6. Adjust the auto sound system’s volume control to a comfortable listening level.
1OdB
OdB
1OdB
20dB
30dB
I i
,.
I
50
I 8
I
100
No power to pc
t
No power to rel
wire with receiv
BASSBOOSTON
FREQUENCYRESPONSE
20dB
AMP NOT
SWITCHING ON
I
I i
500
1K
FREQUENCY(Hz)
I
5K
I i
20K
AMP TURNING
OFF
MEDIUM/HIGH
VOLUME
Speaker Check
impedance
PROTECTION
LAMP ON
Temperature ds
I
50K
NOTE : Raising the Bass frequency allows higher frequencies
to reach the bass
speakers while blocking lower frequencies
from midrange speakers.
Lowering the Bass frequency allows lower frequencies
fo reach the
midrange speakers while blocking higher frequencies
from bass speakers.
Speaker wires !
t-
after you turn your vehicle’s ignition
iem, depending on how you wired
amplifier lights when the amplifier is on.
! of power from your vehicle’s battery
y from discharging, do not operate
w.
Check Tuner/Deck volume level.
Clean contacts on fuse holders.
VIAX) on the side of the amplifier to
xmplifier.
unterclockwise to MIN z
bout one-third of its full range.
1 level.
Jntil the sound begins to distort. Then
,t before where the distortion began.
volume control more than needed to
thirds of its maximum volume.
maximum level you want the amplifier
I a comfortable
ections to radio.
wire with receiver on
listening level.
to determine if it is occurring
before the amp.
BASSBOOSTON
(If you use an ohmmeter to check
speaker resistance, please
remember that DC resistance and
AC impedance may not be the
..r.5K
_
20K
5OK
‘ROTECTION
Temperature down shut
( (Hz)
to reach the buss
es from midrange speakers.
‘r frequencies to reach the
!r frequencies from bass speakers.
r frequencies
24
WARNING
WARRANTY
INFORMATI
--.-._.
_~~__-~-I_~.I~~ll”.
Investigate the layout of your automobile thoroughly before drilling or cutting any holes.
Take care when you work near the gas tanks, lines, hydraulic lines and electrical wiring.
Don’t use the power amplifier unmounted Attach the system securely to the automobile
to prevent damage, particularly in the event of an accident. Don’t mount the system
so that the wire connections are unprotected or are subject to pinching or damage
from nearby objects.
The + 12V DC power wire must be fused at the battery positive terminal connection.
Before making or breaking power connections at the system power terminals.
Disconnect the + 12V wire at the battery end. Confirm your radio/head unit and/or other
equip is turned off while connecting the input jacks and speaker terminals.
If you need to replace the power fuse replace it only with a fuse identical to that
supplied with the system. Using a fuse of different type or rating may result in damage to
this system which isn’t covered by the warranty.
Congratulationson the purchaseof yol
Audiobahn products are manufacturec
advancedtechnology available. Becau
products installed by a factory trained
Audiobahn warrants all electronics to
defectsin materials and workmanship
This warrantv does not apply to:
l Any product, on which the sealsam
tamperedwith, defacedor altered in
l Damagecausedby abuse,misuse, a
l Damagecausedby improper install;
l Any cost or expenserelated to remc
l Subsequent
damageto other compo
l Any product purchasedoutside the 1
This warranty only applies to the orig
The original salesreceipt from an auth
warranty service.
Electronics found to be defective durir
defective product must be shippedpre
which the consumerpurchasedthe pro
in BuenaPark, California in the origin
Any shipping loss or damagewill be tl
shipper.A consumerreturning a prods
488-8595 for a Return Authorization.
must have the Return Authorization N
shipping carton.
Disclaimer
Specifications are subject to change with out notice.
For the most updated Specifications call Audiobahn,
your local authorized Audiobahn dealer,
or check the Audiobahn website.
Www.audiobahninc.com
25
.^
Ship to:
Audiobahn
Warranty Repair Department
7050 Village Drive, Bldg G
Buena Park, CA. 90621
Return Authorization Number..-
-...1.-.”
.._.._. .^,_,_..____I--~
oefore drilling or cutting any holes.
{draulic lines and electrical wiring.
system securely to the automobile
xident. Don’t mount the system
subject to pinching or damage
i positive terminal connection.
system power terminals.
n your radio/head unit and/or other
nd speaker terminals.
with a fuse identical to that
be or rating may result in damage to
WARRANTY
-~-~“.~~-
INFORMATION
..~
Congratulationson the purchaseof your Audiobahn audio equipment!
Audiobahn products are manufacturedwith the highest quality componentsand most
advancedtechnology available. Becauseof this, we recommendthat you have your new
products installed by a factory trained Authorized Audiobahn dealer.
Audiobahn warrants all electronicsto the original consumer/ purchaserto be free from
defectsin materialsand workmanship for a period of ( 1 ) year.
This warrantv does not apnlv to:
l Any product, on which the sealsand I or serial numbers have been broken, removed,
tamperedwith, defacedor altered in any manner
l Damagecausedby abuse,misuse, accident, water or theft
l Damagecausedby improper installation
l Any cost or expenserelated to removal and reinstallation
l Subsequent
damageto other components
l Any product purchasedoutside the USA
This warranty only applies to the original consumer/purchaserand is not transferable.
The original salesreceipt from an authorized Audiobahn dealer is required to obtain
warranty service.
Electronics found to be defective during the warranty period will replaced. A
defectiveproduct must be shippedprepaid to the Authorized Audiobahn Dealer from
which the consumerpurchasedthe product or to the Audiobahn Factory
in BuenaPark, California in the original carton and packing material or their equivalent.
Any shippingloss or damagewill be the responsibility of the consumeror the consumer’s
shipper.A consumerreturning a product to the factory must call ( 800 )
488-8595 for a Return Authorization Number before sendingthe product. All Shipments
must havethe Return Authorization Number clearly marked on the outside of the
shipping carton.
er
lange with out notice.
.tions-_call Audiobahn,
tdiobahn dealer,
lhn website.
inc.com
Ship to:
Audiobahn
WarrantyRepair Department
7050 Village Drive, Bldg G
BuenaPark, CA. 90621
Return Authorization Number:
26
e
0
b
P
;
a@
AudPobahn@
ProductRegistration
for USAandCanadaonly
IMPORTANT:
1. Detachthis sectionof thecard andkeepit withyourrecords.
2. Retainyoursalesreceiptto validatewarrantyservice.
3. If youpurchased
an Audiobahn
product,besureto completetheboxonthe lastpageof thisform
Information
onAudiobahn
authorized
Warranty
Centers
maybeobtainedbywritingAudiobahn
at theaddressbelow
or by calling
714-690=7530
AUDIOBAHN INC.
7050 VILLAGE DRIVE BLDG. G
BUENA PARK CA 90621
es do you own or intendto buy within the next18 months?
OW
Illtend 10buy
9a
IlIeild 10buy
SalelhteSyslemiSerwce
17-1
247
10 7
CellularTelephone
18--l
251
11 ;7
Pager
19_I
26 'I1
12 ?
Call Waiting
20 n
27 ?
13 ,1
Karaoke
21 7
28 n
14 n
VehicleNavlgallonSystem
22 T1
29 s
15 7
VehicleSecurelySystem
23
:1
TEAR THIS PAGE OFF AND KEEP IT WITH YOUR RECEIPT!
30II
16n
hase?l 0
2 q 2nd purchase
ISI purchase
3 r1 3rd 01more
3 r -/Do Not OWII
2 3 Macmtoshor Clone
4 ~MSN
7 11!Other
5 J lnlemel
8i
Do nol haveservice/access
6 7 Prodigy
. products are covered by a full
lres warranty from the original
3. Please refer to the warranty
for guidelines of this warranty
WDIOBAHN INC.
ILLAGE DRIVE BLDG. G
:NA PARK CA 90621
n
I
I
I
I
I
I
I
This product is warranted against all defect in material workmanship for a period of
one year from the date of original purchase. The conditions of this warranty and the
Inc under this warranty are as follows:
extent of the responsibility of Audiobahn
”
”
D
m
1,PROOFOFDATE PURCHASEDWlLLBEREQUlREDFORWARRANTYSERVlCEOFTHlS
AUTHORIZEDWARRANTYSERVICECENTERSMAYi
PRODUCTlNFORMATlONABOUT~-==--D)
ALSO BEOBTAINEDBYCONTACTINGORWRITINGAudiobahn
INC ATTHEADDRESS
LISTEDONTHEFRONTOFTHISCARD.
z
z
2.Thiswarrantywill becomevoid if serviceis performedby anyoneotherthanan approvedAudi-b&n
m
WarrantyServiceCenterresultsin damageto product.
n
3.Thiswarrantydoesnotapplyto anyproductwhichhasbeensubjectto misuse,neglector
accident,or whichhashadthe serialnumberaltered;defacedor removed,or whichhasbeen
D
connected,installed,adjustedor repaired,otherthanin accordancewith the instructions
c1
Ic)
Inc.
furnishedby Audiobahn
m
4.Thiswarrantydoesnot covercarstaticor otherelectricalinterference,
tapeheadcleaning
or spaceadjustments,or laborcostsfor the removalor reinstallationof the unitfor repair.
5.Thesole responsibilityof Audiobahn
Inc underthis Warrantyshallbe limitedto the repairor
K
replacement
thereof at the solediscretionof ~udi~bahn
Inc.
:
1
6.lf it becomesnecessary
to sendthe productor anydefectivepartto Audiobahn
Inc or an authorized
m
warrantyservicestation.the productmustbe shippedin its originalcartonor
,”
equivalentcarton,fully Insured,with shippingchargesprepaid.nudi-bahnlnc
will not
0
assumeanyresponsibilityfor anylossor damageincurredin shipping.
7. ALLIMPLIEDWARRANTIES
EXCEPT
TOTHEEXTENT
PROHIBITED
BYAPPLICABLE
LAWSHALL
HAVENOGREATER
DURATION
THANTHEWARRANTY
PERIOD
SETFORTH
ABOVE.UNDERNO
CIRCUMSTANCES
SHALLAudiobahnk
BELiABLEFORANYLOSSORDAMAGE,
DIRECT
ORCONSEQUENTIAL,
ARISINGOUTOFTHEUSEORINABILITY
TOUSETHEPRODUCT.
BECAUSE
SOMESTATES
DONOTALLOWLIMITATIONS
ONHOWLONGAN IMPLIEDWARRANTY
LASTSOR
EXCLUSIONS
ORLIMITATIONS
OFINCIDENTAL
ORCONSEQUENTIAL
DAMAGES,
THEABOVE
LIMITATIONS
OREXCLUSIONS
MAYNOTAPPLYTOYOU
8. THISWARRANTY
GIVESYOUSPECIFIC
LEGALRIGHTS,
ANDYOUMAYALSOHAVEOTHERRIGHTS
WHICHVARYSTATETOSTATE
9. Shouldyouhaveanydifficultieswith the performance
of this productduringwarranty,or with any
Audiobahn
authorizedservicecenters,you maycontactthe Audiobahn
NationalService
Mangersat theaddresslistedon the frontof this cardor call 714-690-7530for a listingof
AuthorizedWarrantyserviceCentersin yoursarea.
281-0607-OO-PRINTED
IN KOREA
PRODUCT REGIDTRATION CARD
Thankyou for selectinga high-qualityproductfrom AU~;O~CI~~
Wehopeyouarecompletelysatisfiedwith yourpurchase We’dlike
to help serveyou betterby finding out moreaboutyourreasonsfor choosing~udiobahn
Pleasetakea few momentsto fill out the reglstratloninformationon this cardandanswera
fewquestionsaboutyourselfandyourproductThen.returnthe cardto Audiobahn
wIthInIO
daysof purchase.Youranswerswill be keptstrictlyconfidentialWeappreciateyourresponse1
Are there any childrenin your household?
I-
Yes
II yes please~pec~lvaqeidlige
4 [ ~- CompletedColleg
I ~ SomeHI(J~Sci~ool
2
H1yi1Schol Glddilate
5 :- SomeGraduateSC
3
SomeColleye
G?, Comp;etetlGradu
I 7 Prolessroilalllecliliical
5 -1 ClerrcaliServlce
z
6 1 Trddesnidn/Mac
I UpperMaliagernenVExecullve
3 1MIddIe Manayelnenl
7 [:I Self-Employed/F
4
SaiesiMarketrny
8 -1 FoodService
1
Ulider$13 000
?
1$10.000-$19999
3 ~I$20.000-$29,999
1q Woofers
I
4 -l$30,000-$39,999
7
5 1:: $40,000-$49,999
81
6
1$50.000-$59,999
9
2 7 Wire
67
77
3 q Components
8 7 EqualueriDSPProcessorModule
1 ‘__ Newspap Adverllsement
7 !-Recommended b’
4 0 Capacilors
9 g Ampl~her
2 LTV Commercral
8 U On-he lnlormalr~
5 fl Crossovers
Enclosures
Accessorres
10 ~_ Full RangeSpeakers
GroupA (Pleasechecktwo)
9 i-Store Display
3 !. RadioCommercial
4 ~ MdgazlIle Advertrsenient
10 i_ SpecralPromotro
5 L Recolnmeiidedby FriendiFamlly
11 LOther
6 1-1nu~ioboknNameiRepulallon
Groupi3 (Pleasechecktwo)
I? ~I Warrallty
14 0 Features
13 il QualilyiRellabrlily
15 m AppearanceiDesrgll
1EII
17 L
8 Whattype of music do you listento most often?(Pleasec
1
I
-Rock
4 r-1 Rap
1;
i .I; Jaz7
5 Ccountry
SC
3 my Blues
6 C Classical
9i
DUCT REGIDTRATION CARD
~roduclfroni ~~di~bahn
yourpurchase.We’dlike
oreaboutyourreasonsfor choosingAudiobahn
eglstrationinforrnatlonon this cardandanswera
witli~n10
duct Then.returnthe cardto ~~di~bahn
3 strrctlyconfidentialWeappreciateyou response1
I/ yes oleasespeirly aye ralige
4c
13-16
SomeHIgil Scilooi
4 iI_ CompletedCollege
2
HighSchoolGiadLiale
5 71 SomeGradualeSchool
3-
Some Colleqe
6 7 CompletedGraduateSchool
I
iss.
3iTi-12
5Fl7s,UP
7 17 Vocation/Technrcal
School
What best Describesyour primary occupation?
1
1 Professlonaliieciililcal
5 n Clerical/ServiceWorker
9 iI homemaker
Student
6 1 Tradesnian/Machrne
OperatoritStudeilt
10 n
3 ~’MrddleMallagement
7 ci Self-EmployediBusrnss
Owner
11 cj Retired
4 : -1SaiesiMarkellng
8 ? FoodServrce
12 L_iOther
1 -1UpperManagemenl/Execuilve
I
1Under$10 000
4 ~i$30,000-$39,999
7 :1$60.000-$69.999
10 0$90,000-$99,999
i 1 I$1 00,000 and over
2 _I $1o.ooo-$19 999
5 ! 1$40,000-$49,999
8 14 $70,000-$79.999
3 ~~$20000-$29,999
6 ~I$50.000459,999
9 n $80.000~$89,999
6 ? Enclosures
7 -1~1Accessorres
GroupA (Pleasechecktwo)
L
Recommendedby StoreSalesperson
8 11 EqualrrerlDSPProcessorModLrle
i ! _ NewspaperAdvertrsement
7
91
I i j TVCommercral
8 LI_ On-lrnelniomiatron
r9 L StoreDrsplay
Aniplrher
3 1-1RadioCommercial
IO --I Full RangeSpeakers
4 1 MagazineAdvertiselnent
10 L1 SpecialPromotion
5 L_ RecoInmendedby Frrend/Famrly
11 i
Other
6 L-mn,~i,bah,Nanie/Reputation
GroupB (Pleasechecktwo)
ire you purchasedthis product?
:
q-1
:
12 1 Warranty
14 3 FeattIres
i6 [7 Easeof Operalion
13 1 Qualrty/Rel~ab~lily
15 g Appearance/Design
17 0 Other
1 Whattype of music do you listento most often?(Pleasecheck one)
I
1 Rock
4 ORop
1 1 Rap
2
LJdz7
5 ;II; Couniry
8 c Rhylhm& Blues
I I 0 EasyLrstenrng
6 ‘7 ClassIcal
9 -Reggae
12 0 Alternative
3 -Blues
IO ONewAge
Which of the following products/servicesdo you own or intendto buy within the next 18 months?
OWll
D KEEP IT WITH YOUR RECEIPT!
-----
i
z
rformedby anyoneotherthanan approvedAQudiobahn
xoduct.
iich hasbeensubjectto misuse,neglector
lltered;defacedor removed,or whichhasbeen
erthanin accordancewith the instructions
r electricalInterference,
tapeheadcleaning
movalor reinstallationof the unitfor repair.
ICunderthis Warrantyshallbe limitedto the repalror
Audiobahn
Inc.
anydefectivepartto Audiobahn
Inc or an authorized
;hlppedin its originalcartonor
chargesprepaid.Audiobahnlnc
Will not
ageincurredin shipping.
EXTENT
PROHIBITED
BYAPPLICABLE
LAWSHALL
/ARRANTY
PERIOD
SETFORTH
ABOVE.UNDERNO
Inc BELiABLEFORANYLOSSORDAMAGE,
DIRECT
USEORINABILITY
TOUSETHEPRODUCT.
BECAUSE
; ONHOWLONGAN IMPLIEDWARRANTY
LASTSOR
ALORCONSEQUENTIAL
DAMAGES,
THEABOVE
?LYTOYOU.
\L RIGHTS,
ANDYOUMAYALSOHAVEOTHERRIGHTS
ormanceof this productduringwarranty,or with any
you mayCOntaCt the Audiobahn
NationalSerViCe
this card or call 714-690-7530for a listing of
area
281-0607-OO-PRINTED
IN KOREA
1;;
Intendlo buy
17 0
24 q
10 0
CellularTelephone
18 0
25 q
11 a
Pager
19 0
26 q
‘la
12 n
Call Waiting
20 q
27 q
5n
13 cl
Karaoke
21 0
28 0
6U
14
VehicleNavigationSystem
22 q
290
Modem
70
15 0
VehrcleSecuritySystem
23 0
30 0
LargeScreenTV (35” or large)
80
16 0
30
3rd or more
90
LaptopComputer
20
Color Monrtor
30
CD-ROM
ComputerSpeakers
ColorPrinter
i !I IBM PCor Clone
REQUIREDFORWARRANTYSERVICEOFTHIS
.ba~.n AUTHORIZEDWARRANTYSERVICECENTERSMAY 2 : 4 1
{ WRITING Audiobahn
INC AT THE ADDRESS
OW
SalelhteSyslemiServrce
l!I
Is this your first Audiobahn
defect in material workmanship for a period of
:hase. The conditions of this warranty and the
.ahn Inc under this warranty are as follows:
lnlend IObuy
HomeDesktopPC
q
purchase?10
ist purchase
2 q 2nd purchase
2 a Macintoshor Clone
3 0 Do Not Own
Which on-lineservice/networkdo you subscribeto?
1 :I AmericaOnline
4gMSN
7 0 Other
2 0 CompuServe
5 g Internet
8 0 Do not haveservice/access
3 ‘11 GEnre
6 1 Prodigy
All Audiobahn Inc. products are covered by a full
1 year manufactures warranty from the original
date of purchase. Please refer to the warranty
information card for guidelines of this warraniy
AUDIOBAHN INC.
7050 VILLAGE DRIVE BLDG. G
BUENA PARK CA 90621
Audtobahn’
FIRSFCLASSSTAMP
[PostOIlIceWillnot deliver
wilhoulproperpostage)
AUDIOBAHN INC.
7050 VILLAGE DRIVE BLDG. G
BUENA PARK CA 90621