1
Download NUC710 EVB user`s manual
Transcript
NUC710 EVB User manual NUC710 Evaluation Board User manual The information described in this document is the exclusive intellectual property of Nuvoton Electronics Corporation and shall not be reproduced without permission from Nuvoton. Nuvoton is providing this document only for reference purposes of NUC710-based system design. Nuvoton assumes no responsibility for errors or omissions. All data and specifications are subject to change without notice. .For additional information or questions, please contact: Nuvoton Electronics Corp. NUC710 EVB USER MANUAL Revision history VERSION DATE PAGE DESCRIPTION A FEB 06, 2006 - Initial Issued B MAR 08, 2006 - Update C July 20, 2006 - Add AUO TFT panel information D Feb 12, 2007 - Update RMII/USB information and pictures E Apr 6,2009 - Change part number to NUC710 -I- Publication Release Date: Apr 6, 2009 Revision: E NUC710 EVB USER MANUAL Table of Contents1. 2. OVERVIEW ................................................................................................................................. 1 1.1 Features.......................................................................................................................... 2 1.2 System Architecture........................................................................................................ 5 Core module board function block ...................................................................................5 1.2.2 Application board function block ......................................................................................6 BOARD CONFIGURATION ........................................................................................................ 7 2.1 2.2 3. 1.2.1 Core Module configuration.............................................................................................. 7 2.1.1 System Clock Source selection (JP1) ..............................................................................7 2.1.2 Endien Mode selection (JP2) ...........................................................................................7 2.1.3 Boot Flash type selection (R5, R6)...................................................................................8 2.1.4 Reset Button (SP1) ..........................................................................................................8 Application board configuration....................................................................................... 9 2.2.1 UART1/UART2/PS2 selection (JP1~JP6) ........................................................................9 2.2.2 UART3/AC97/PWM selection (SW8~SW10) .................................................................10 2.2.3 I2C/SPI/TIMER-OUT selection (SW1~SW3)..................................................................11 2.2.4 KPI/RMII settings (SW11~SW14) ..................................................................................12 2.2.5 SMC/SD selection (SW4~SW7).....................................................................................13 CIRCUIT DESCRIPTION .......................................................................................................... 15 3.1 SDRAM ......................................................................................................................... 15 3.2 FLASH .......................................................................................................................... 16 3.3 USB 1.1 Host/Device .................................................................................................... 17 3.4 UART ............................................................................................................................ 18 3.5 PS/2 .............................................................................................................................. 20 3.6 LCD interface ................................................................................................................ 21 3.6.1 CASIO 2.5” TFT LCD .....................................................................................................21 3.6.2 AUO 3” TFT LCD module ...............................................................................................22 3.7 Keypad Interface ........................................................................................................... 23 3.8 JTAG Interface.............................................................................................................. 23 3.9 Ethernet ........................................................................................................................ 24 3.10 RTC............................................................................................................................... 25 3.11 SPI Interface ................................................................................................................. 25 3.12 Timer output.................................................................................................................. 26 3.13 I2C ................................................................................................................................ 26 3.14 SD card interface .......................................................................................................... 27 - II - NUC710 EVB USER MANUAL 4. 5. 3.15 Ext. DMA interface ........................................................................................................ 27 3.16 SMC interface ............................................................................................................... 28 3.17 GPIO TEST interface.................................................................................................... 29 3.18 EBI interface ................................................................................................................. 30 3.19 LED display................................................................................................................... 31 SCHEMATIC ............................................................................................................................. 32 4.1 Core Module board ....................................................................................................... 32 4.2 Application board .......................................................................................................... 41 4.3 AUO TFT panel board................................................................................................... 55 BOM LIST.................................................................................................................................. 56 5.1 Core Module board ....................................................................................................... 56 5.2 Application board .......................................................................................................... 58 5.3 AUO 3” TFT panel module board ................................................................................. 62 - III - Publication Release Date: Apr 6, 2009 Revision: E NUC710 EVB USER MANUAL 1. OVERVIEW The NUC710 evaluation board consists of a core module and an application board. The core module board consists of ARM7-TDMI core 32-bit MCU NUC710, 16MByte SDRAM, 4MByte NOR FLASH, one RS-232 port for console communication, a USB 1.1 host with USB A type connector and a USB 1.1 device port with USB mini-B type connector. All function is directly supported by NUC710. Picture 1-1 -1- Publication Release Date: Apr 6, 2009 Revision: E NUC710 EVB USER MANUAL 1.1 Features The NUC710 core module board offers the smallest system for evaluating this chip. It’s easily to build up user’s application system by using this core module and the application board. For more detail information about NUC710 development platform please refer to below: NUC710 Core Module: MCU: ARM7TDMI-based NUC710 operating up to 80MHz speed. Boot FLASH: Board supports up to 8MB (4Mx16) FLASH, one 2MBx16 FLASH onboard. SDRAM: Board supports up to 32MB (8Mx16x2 banks) SDRAM, totally 16MB onboard. USB: One USB1.1 Host + one USB 1.1 device port connector. UART: One TX/RX signals only RS-232 port (UART0) for debug console communication. JTAG: 14-pin header JTAG debug interface. Picture 1-2 -2- NUC710 EVB USER MANUAL Application Board: Network: A 10/100Mbps Ethernet port supported with DM9161A by NUC710 RMII interface. LCD: 1.Supports Casio 2.5” 480x240 TFT LCD by NUC710’s LCD controller interface. 2. Supports AUO 3” 960x240 TFT LCD by NUC710’s LCD controller interface. SD: Supports 4-bit mode SD memory card interface by NUC710’s SD interface I2C: One 64kB EEPROM onboard connected with NUC710’s I2C interface. Smart card: Two 7816-3 ports supported by NUC710’s SMC controller. UART: Three UART ports supported (Male type) from NUC710. PS/2: One PS/2 port supported by NUC710’s PS/2 interface. RTC: Real-time clock supported by NUC710’s RTC controller. Matrix Keypad: Supports 2-Row x 8-Col matrix keypad by NUC710’s KPI. SPI: One serial flash connected with NUC710’s SPI interface. Audio: Audio-out/in supported with ALC-203 audio codec with NUC710’s AC-97 interface. LED debug display: 8-LED display connected with NUC710’s EBI bank0. PWM: 4-channel PWM connector supported by NUC710’s PWM controller. Timer out LED display: Two LED display connected with NUC710’s timer out pins. -3- Publication Release Date: Apr 6, 2009 Revision: E NUC710 EVB USER MANUAL Picture 1-3 -4- NUC710 EVB USER MANUAL 1.2 System Architecture 1.2.1 Core module board function block EBI Ext. Connector GPIO Ext. Connector SDRAM W986416 EBI Ext. pins Multi-Function Ext. pins SDRAM W986416 RTC EBI NUC710 INT3 BOOT FLASH USB interface Device TAP 3.3V/ 1.8V Power module 3V BAT -->1.8V USB Host Uart_0 Push Button Transceiver Power Switch JTAG Connector USB Device USB Host Con. Con. DB9 Con. Figure 1-4 -5- Publication Release Date: Apr 6, 2009 Revision: E NUC710 EVB USER MANUAL 1.2.2 Application board function block ECS0 EBI bank0 LED display EBI Ext. Connector Gpio[30:41] NUC710 Core Module LCD display GPIO Ext. Connector Gpio[0:4] Gpio[0:5] UART1 I2C SPI Figure 1-5 -6- Ext. DMA interface Switch UART2 Gpio[20:29] Timer out LED display Switch AC-97 Audio Codec Gpio[11:14] PS/2 Switch Switch UART3 GPIO TEST pins SMC SD Gpio[42:51] Switch PWM CON. EBI TEST pins KPI Ethernet PHY NUC710 EVB USER MANUAL 2. BOARD CONFIGURATION The NUC710 evaluation board has setting with default configuration. You may using this board with the default settings directly. However, it’s easy to change the settings according to your requirement. Please notice that and conform to correct settings you want before using this board. 2.1 2.1.1 Core Module configuration System Clock Source selection (JP1) The evaluation board supports system clock source selection. To short 1-2 of JP1 (pull-high SDD15) will set the system operating speed to 80MHz (enable internal PLL) or short 2-3 of JP1 (pull-low SDD15) to set the operating speed to the same as external crystal source (disable internal PLL). JUMPER SETTING JUMPER SHORT 1-2 SHORT 2-3 Internal System Clock Select JP1 Enable PLL(80MHz) Disable PLL(15MHz) CVDD33 JP1 R15 80MHZ 1 2 3 SDD15 4.7K 15MHZ 15M/80M If pin D15 is pull-up, the PLL output clock is used as internal system clock If pin D15 is pull-down, the external clock from EXTAL pin is served as internal system clock. 2.1.2 Endien Mode selection (JP2) The evaluation board supports system endian mode selection. To short 1-2 of JP2 (pull-high SDD14) to set system operating mode at little endian mode or short 2-3 of JP2 (pull-low SDD14) can set system operating mode at Big endian mode. JUMPER SETTING JUMPER SHORT 1-2 SHORT 2-3 Endian mode Select JP2 Little Big -7- Publication Release Date: Apr 6, 2009 Revision: E NUC710 EVB USER MANUAL CVDD33 JP1 R15 80MHZ 1 2 3 SDD15 4.7K 15MHZ 15M/80M If pin D15 is pull-up, the PLL output clock is used as internal system clock If pin D15 is pull-down, the external clock from EXTAL pin is served as internal system clock. 2.1.3 Boot Flash type selection (R5, R6) There are two resistors for Boot Flash type selection. The default setting connected FA21 pin to VDD33 for WINBOND Flash. Connected FA21 to A21 if using AMD Flash and will supported up to 4Mx16 size Flash for Boot Flash bank. OPTIONAL SELECT Flash Type R5 R6 FLASH RYPE On Off AMD Off On WINBOND FA21=VDD_F for WINBOND FLASH FA21=A21 for AMD FLASH Default:AMD Flash AD21 FA21 R5 0 R6 4.7K VDD33 NOP 2.1.4 Reset Button (SP1) The push button SP１ is the system reset button that connected to a reset IC (SP70５S) and it will generate about 200ms low pulse for whole system resetting . PUSH BUTTON BUTTON System Reset SP1 -8- NUC710 EVB USER MANUAL VDD VDD R3 R4 10K U1A nSRST 10K 1 U2 VDD 2 1 4 6 3 VCC MR PFI WDI RESET WDO PFO GND 7 8 5 3 nRESET 2 74LS08 VDD SP705 SP1 CB2 SW PUSHBUTTON 2.2 2.2.1 0.1uF Application board configuration UART1/UART2/PS2 selection (JP1~JP6) NUC710 offers a multi-function port which can supports UART1/2 or PS2 interface by difference settings. To Use PS2 function please short 2-3 of JP5 and JP6, or short 1-2 to choose UART function. JUMPER SETTINGS FUNCTION SELECT JP1 JP2 JP3 JP4 JP5 JP6 UART1 (TX/RX) 1-2 1-2 - - - - UART1 (TX/RX/CTS/RTS) 1-2 1-2 1-2 1-2 - - UART2 2-3 2-3 2-3 2-3 1-2 1-2 PS2 - - - - 2-3 2-3 -9- Publication Release Date: Apr 6, 2009 Revision: E NUC710 EVB USER MANUAL UTXD/URXD SELECT JP1 UTXD1 UTXD UTXD2 1 2 3 UTXD SEL JP2 URXD1 URXD URXD2 1 2 3 URXD SEL UTXD/URXD SELECT JP3 RTS1 RXD2/RTS1 RXD2 1 2 3 RTS1/RXD2 SEL JP4 CTS1 TXD2/CTS1 TXD2 1 2 3 CTS1/TXD2 SEL UTXD/URXD SELECT JP5 TXD2/CTS1 TXD2/CTS1/PS2_CLK PS2_CLK 1 2 3 UART/PS2_CLK SEL JP6 RXD2/RTS1 RXD2/RTS1/PS2_DAT PS2_DAT 1 2 3 UART/PS2_DAT SEL 2.2.2 UART3/AC97/PWM selection (SW8~SW10) NUC710 supports a multi-function port which supports UART3 function or AC97 or PWM output by difference settings. Please refer to the following table for more information: SWITCH SETTINGS FUNCTION SELECT SW8 SW9 SW10 UART3 (TX/RX/DTR/DSR) OFF ON ON PWM OFF ON OFF AC97 ON OFF OFF - 10 - NUC710 EVB USER MANUAL GPIO0 GPIO1 GPIO2 GPIO3 GPIO4 R28 1 2 3 4 RP7 22 8 7 6 5 8P4R-22 AC97nRST/I2SSCLK AC97DATI/I2SDATI/PWM0/DTR3 AC97DATO/I2SDATO/PWM1/DSR3 AC97SYNC/I2SWS/PWM2/TXD3 AC97BCLK/I2SBCLK/PWM3/RXD3 SW8 1 2 3 4 5 SW9 8 7 6 5 1 2 3 4 SW 1X5 10 9 8 7 6 AC97_nRST AC97_DATI AC97_DATO AC97_SYNC AC97_BCLK PWM0/DTR3 PWM1/DSR3 PWM2/TXD3 PWM3/RXD3 PWM0/DTR3 PWM1/DSR3 PWM2/TXD3 PWM3/RXD3 SW 1X4 SW10 PWM0/DTR3 PWM1/DSR3 PWM2/TXD3 PWM3/RXD3 PW0/DTR3 PWM1/DSR3 PWM2/TXD3 PWM3/RXD3 8 7 6 5 VDD DTR3 DSR3 TXD3 RXD3 1 2 3 4 RP8 1 2 3 4 SW 1X4 8P4R-10K J7 1 2 PWM0 3 PWM1 4 PWM2 PWM3 RP9 1 2 3 4 8 7 6 5 8 7 6 5 PWM0 PWM1 PWM2 PWM3 8P4R-0 2.2.3 PWM Header I2C/SPI/TIMER-OUT selection (SW1~SW3) NUC710 supports a multi-function port which can supports I2C or SPI or Timer-out function by difference settings. The I2C interface connected to an EEPROM, the SPI interface connected to a serial flash and the timer-out signals connected to LED display. Please refer to the following table for more information: FUNCTION SELECT I2C SPI TIMER OUT SWITCH SETTINGS DEVICE SW1 SW2 SW3 24LC64 ON OFF OFF CASIO PANNEL OFF ON OFF W25P16 OFF OFF ON LED ON OFF OFF - 11 - Publication Release Date: Apr 6, 2009 Revision: E NUC710 EVB USER MANUAL RP3 GPIO11 GPIO12 GPIO13 GPIO14 1 2 3 4 SW1 8 7 6 5 SCL0/SFRM/TIMER0 SDA0/SSPTXD/TIMER1 SCL1/SCLK SDA1/SSPRXD 8 7 6 5 8P4R-22 1 2 3 4 TIMER0 TIMER1 SCL SDA 1 2 3 4 SFRM SSPTXD SCLK SSPRXD 1 2 3 4 NF_CS NF_DI NF_CLK NF_DO SW 1X4 SW2 8 7 6 5 SFRM SSPTXD SCLK SSPRXD SW 1X4 SW3 8 7 6 5 SW 1X4 2.2.4 KPI/RMII settings (SW11~SW14) The NUC710 offers a multi-function port which can supports KPI or RMII function by difference settings. The KPI controller for matrix keypad and the RMII is Ethernet communication interface. Please refer to the following table for more information: SWITCH SETTINGS FUNCTION SELECT SW11 SW12 SW13 SW14 KPI ON ON OFF OFF RMII OFF OFF ON ON GPIO42 GPIO43 GPIO44 GPIO45 GPIO46 GPIO47 GPIO48 GPIO49 GPIO50 GPIO51 RP16 1 2 3 4 RP17 1 2 3 4 R76 R77 8 8P4R-22 7 6 5 8 8P4R-22 7 6 5 22 22 KPI_COL0/PHY_RXERR KPI_COL1/PHY_CRSDV KPI_COL2/PHY_RXD0 KPI_COL3/PHY_RXD1 KPI_COL4/PHY_REFCLK KPI_COL5/PHY_TXEN KPI_COL6/PHY_TXD0 KPI_COL7/PHY_TXD1 1 2 3 4 5 6 7 8 SW11 SW 1X8 16 15 14 13 12 11 10 9 COL0 COL1 COL2 COL3 COL4 COL5 COL6 COL7 KPI_ROW0/PHY_MDIO KPI_ROW1/PHY_MDC 1 2 SW12 SW 1X2 4 3 ROW0 ROW1 - 12 - NUC710 EVB USER MANUAL PHY_RXERR PHY_CRSDV PHY_RXD0 PHY_RXD1 PHY_REFCLK PHY_TXEN PHY_TXD0 PHY_TXD1 PHY_MDIO PHY_MDC 2.2.5 1 2 3 4 5 6 7 8 SW13 SW 1X8 16 15 14 13 12 11 10 9 KPI_COL0/PHY_RXERR KPI_COL1/PHY_CRSDV KPI_COL2/PHY_RXD0 KPI_COL3/PHY_RXD1 KPI_COL4/PHY_REFCLK KPI_COL5/PHY_TXEN KPI_COL6/PHY_TXD0 KPI_COL7/PHY_TXD1 1 2 SW14 SW 1X2 4 3 KPI_ROW0/PHY_MDIO KPI_ROW1/PHY_MDC SMC/SD selection (SW4~SW7) The NUC710 offers a multi-function port which can supports smart card and SD memory card by difference settings. The SMC interface can supports up to two smart cards and the SD memory interface can supports one SD memory card. Please see the following table for more information: SWITCH SETTINGS FUNCTION SELECT SW4 SW5 SW6 SW7 SMC OFF OFF ON ON SD ON ON OFF OFF RP4 GPIO20 GPIO21 GPIO22 GPIO23 GPIO24 GPIO25 GPIO26 GPIO27 1 2 3 4 1 2 3 4 RP5 GPIO28 GPIO29 R12 R13 SC1_PWR SC1_PRES SC1_RST SC1_CLK SC1_DAT SC0_PWR SC0_PRES SC0_RST SC0_CLK SC0_DAT 8P4R-22 8 7 6 5 8 7 6 5 8P4R-22 22 22 SC1_PWR/nXDACK SC1_PRES/nXDREQ SC1_RST/SD_CD SC1_CLK/SD_PWR SC1_DAT/SD_DAT3 SC0_PWR/SD_DAT2 SC0_PRES/SD_DAT1 SC0_RST/SD_DAT0 SC0_CLK/SD_CLK SC0_DAT/SD_CMD SW6 1 2 3 4 5 6 7 8 SW7 1 2 SW4 1 2 3 4 5 6 7 8 SW5 1 2 SW 1X8 16 15 14 13 12 11 10 9 nXDACK nXDREQ SD_CD SD_PWR SD_DAT3 SD_DAT2 SD_DAT1 SD_DAT0 SW 1X2 4 3 SD_CLK SD_CMD SW 1X8 16 15 14 13 12 11 10 9 SC1_PWR/nXDACK SC1_PRES/nXDREQ SC1_RST/SD_CD SC1_CLK/SD_PWR SC1_DAT/SD_DAT3 SC0_PWR/SD_DAT2 SC0_PRES/SD_DAT1 SC0_RST/SD_DAT0 SW 1X2 4 3 SC0_CLK/SD_CLK SC0_DAT/SD_CMD - 13 - Publication Release Date: Apr 6, 2009 Revision: E NUC710 EVB USER MANUAL 2.2.5.1. SMART CARD port0 POWER type selection jumper (JP8) This development board supports a smart card port0 power type selection Jumper which can choose the smart card port0 supply voltage type supported by smart card power switch LTC1555L. Please see the following table for more detail information. JUMPER SETTING POWER SELECT JP8 5V 1-2 3V 2-3 JP8 VDD33 3V/5V GND 1 2 3 3V/5V SEL - 14 - NUC710 EVB USER MANUAL 3. CIRCUIT DESCRIPTION 3.1 SDRAM TOTAL SIZE MEMORY CONFIGURATIONS 16Mbyte BANK BUS WIDTH PART NUMBER 0/1 W986416 W981216 W982516 32Mbyte 1Mx16x4 Banks 2Mx16x4 Banks 0/1 32-bit 32-bit 64Mbyte 4Mx16x4 Banks 0/1 32-bit SDD[0..31] AD[0..21] nWBE[0..3] nSWE nOE nBTCS nSRAS nSCAS SDMCLK MCKE nSCS0 nRESET SDD[0..31] AD[0..21] nWBE[0..3] nSWE nOE nBTCS nSRAS nSCAS SDMCLK MCKE nSCS0 nRESET SDRAM W986416AH 1M x16 x 4 BANKs W981216AH 2M x16 x 4 BANKs W982516AH 4M x16 x 4 BANKs U3 SDD0 SDD1 SDD2 SDD3 SDD4 SDD5 SDD6 SDD7 SDD8 SDD9 SDD10 SDD11 SDD12 SDD13 SDD14 SDD15 2 4 5 7 8 10 11 13 42 44 45 47 48 50 51 53 nWBE0 nWBE1 nSWE nSCAS nSRAS nSCS0 AD13 AD14 15 39 16 17 18 19 20 21 VDD33 43 9 3 49 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQML DQMH /WE /CAS /RAS /CS BA0 BA1 U4 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12 CLK CKE VSS VSS VSS VSSQ VSSQ VSSQ VSSQ VDDQ VDDQ VDDQ VDDQ NC VDD VDD VDD 23 24 25 26 29 30 31 32 33 34 22 35 36 38 37 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 AD8 AD9 AD10 AD11 AD12 SDMCLK MCKE 28 41 54 6 12 46 52 nWBE2 nWBE3 nSWE nSCAS nSRAS nSCS0 AD13 AD14 40 27 14 1 SDD16 SDD17 SDD18 SDD19 SDD20 SDD21 SDD22 SDD23 SDD24 SDD25 SDD26 SDD27 SDD28 SDD29 SDD30 SDD31 VDD33 VDD33 W986416EH 2 4 5 7 8 10 11 13 42 44 45 47 48 50 51 53 15 39 16 17 18 19 20 21 43 9 3 49 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQML DQMH /WE /CAS /RAS /CS BA0 BA1 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12 CLK CKE VSS VSS VSS VSSQ VSSQ VSSQ VSSQ VDDQ VDDQ VDDQ VDDQ NC VDD VDD VDD 23 24 25 26 29 30 31 32 33 34 22 35 36 38 37 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 AD8 AD9 AD10 AD11 AD12 SDMCLK MCKE 28 41 54 6 12 46 52 40 27 14 1 VDD33 W986416EH - 15 - Publication Release Date: Apr 6, 2009 Revision: E NUC710 EVB USER MANUAL 3.2 FLASH TOTAL SIZE MEMORY CONFIGURATIONS BUS WIDTH PART NUMBER 16-bit 16-bit W28J160 4Mbyte 1Mx16bits 2Mx16bits W19L320ABT 8Mbyte 4Mx16bits 16-bit Am29LV640 2Mbyte BOOT FLASH FA21=VDD_F for WINBOND FLASH FA21=A21 for AMD FLASH Default:AMD Flash AD21 FA21 R5 0 R6 4.7K VDD33 NOP AD15 AD14 AD13 AD12 AD11 AD10 AD9 AD8 AD19 AD20 nWBE1 nRESET FA21 VDD33 AD18 AD17 AD7 AD6 AD5 AD4 AD3 AD2 AD1 U5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 A15 A14 A13 A12 A11 A10 A9 A8 A19 A20 WE RESET# VPP WP# RY/BY # A18 A17 A7 A6 A5 A4 A3 A2 A1 A16 BY TE# VSS DQ15/A-1 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# VSS CE# A0 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 AD16 VDD33 GND SDD15 SDD7 SDD14 SDD6 SDD13 SDD5 SDD12 SDD4 VDD33 SDD11 SDD3 SDD10 SDD2 SDD9 SDD1 SDD8 SDD0 nOE GND nBTCS AD0 W19B/L320S 1,2,4MB(up to 8MB AMD FLASH) am29LV800B 512Kx16 am29LV160D 1Mx16 am29LV320D 2Mx16 W19B/L320S 2Mx16 - 16 - NUC710 EVB USER MANUAL 3.3 USB 1.1 Host/Device USB PORT DESCRIPTION Host CON7 of Core module board(A-Type Connector) Device CON8 of Core module board(mini B-Type Connector) USBVDD USBVDD USB HOST C9 R13 33uF/16V U9 LL5 10K USB_ON/OFF USB_FLAG USB_ON/OFF USB_FLAG R14 1 2 3 4 10K CTL1 OUT1 FLG1 IN FLG2 GND CTL2 OUT2 8 7 6 5 1 CB17 0.1uF R15 CON7 FB C10 CD2 33uF/16V D1D1+ 2 3 4 0.01uF AMC3526H VBUS DD+ GND USB A-TYPE 10K FB LL6 R16 R17 15K 15K NOP USBVDD R18 USB Device 0 CON8 U1B R19 4 6 nRESET nRESET 1.5K 1 2 3 4 5 D2D2+ 5 74LS08 FB VBUS DD+ NC GND LL7 mimi USB B-TYPE The 1.5k resistor on D+ indicates to USB that a full speed device is connected when the device is hot plugged into a USB hub or host port. If the reset time is >10ms from plugging in the device, then there is a possibility that the device will still be held in reset at the time that USB tries to enumerate the device. This will result in USB marking the device as an "unknown device" as it is unable to enumerate it. The solution in this case is to connect in series with 1.5k pull up resistor with a AND gate(74LS08) with system reset signal(nRESET) so that USB D+ line will not pull high until after the device comes out of reset state. - 17 - Publication Release Date: Apr 6, 2009 Revision: E NUC710 EVB USER MANUAL 3.4 UART UART PORT DESCRIPTION Port 0 CON6 of Core module board(Female Type) Port 1 CON5 of AP board(Male Type) Port 2 CON6 of AP board (Male Type) Port 3 CON7 of AP board (Male Type) VDD33 GREEN_LED LED3 RXD0 2 1 R11 1K GREEN_LED LED4 TXD0 2 1 R12 1K Console UART(TX/RX only) CON6 + CC1 VDD 1uF/16V + CC5 1uF/16V + U8 + 1 2 3 4 5 6 7 8 C1+ V+ C1C2+ C2VT2_OUT R2_IN VCC GND T1_OUT R1_IN R1_OUT T1_IN T2_IN R2_OUT 16 15 14 13 12 11 10 9 CC2 1uF/16V URXD + CC4 UTXD CC3 1uF/16V 1uF/16V GND UTXD URXD RXD0 TXD0 1 6 2 7 3 8 4 9 5 DSUB-9 FeMale Female and Male are use difference pin define!!! SP232ECA - 18 - NUC710 EVB USER MANUAL UART1 + CC1 VDD CC3 CC4 0.1uF + CC5 0.1uF + URTS1 UCTS1 + U1 1 2 3 4 5 6 7 8 C1+ V+ C1C2+ C2VT2_OUT R2_IN VCC GND T1_OUT R1_IN R1_OUT T1_IN T2_IN R2_OUT 16 15 14 13 12 11 10 9 CC2 0.1uF + 0.1uF 0.1uF UTXD1 URXD1 RXD1 TXD1 RTS1 CTS1 MAX202C UART2 + CC6 VDD CC8 0.1uF CC9 0.1uF + CC10 0.1uF U2 + 1 2 3 4 5 6 7 8 C1+ V+ C1C2+ C2VT2_OUT R2_IN VCC GND T1_OUT R1_IN R1_OUT T1_IN T2_IN R2_OUT 16 15 14 13 12 11 10 9 CC7 0.1uF + + 0.1uF UTXD2 URXD2 RXD2 TXD2 MAX202C (UART1/2) CON5 GND 5 9 4 8 3 7 2 6 1 UCTS1 UTXD URTS1 URXD DB9_Male Male - 19 - Publication Release Date: Apr 6, 2009 Revision: E NUC710 EVB USER MANUAL UART3 (UARTC) + CC11 GND VDD 0.1uF CC14 U7 0.1uF + CC15 0.1uF + UDTR3 UDSR3 1 2 3 4 5 6 7 8 C1+ VCC V+ GND C1T1_OUT C2+ R1_IN C2R1_OUT VT1_IN T2_OUT T2_IN R2_IN R2_OUT 16 15 14 13 12 11 10 9 CC12 0.1uF + + CC13 UDTR3 0.1uF UTXD3 URXD3 UDSR3 UTXD3 URXD3 RXD3 TXD3 DTR3 DSR3 MAX202C 3.5 PS/2 PS/2 PORT IN/OUT SIGNALS DESCRIPTION PS/2 Keyboard only DAT,CLK CON11 (Mini-DIN-6) PS/2 LL8 FB 5V RK1 4.7K RK2 4.7K PS2 CON LL10 PS2_DAT CON11 1 2 3 4 5 6 FB LL11 PS2_CLK CD6 CD7 47pF 47pF FB CD8 LL12 1uF FB PS/2 CON Please notice that NUC710 PS/2 port can only supports PS/2 interface keyboard, don’t supports PS/2 mouse device. - 20 - NUC710 EVB USER MANUAL 3.6 LCD interface 3.6.1 CASIO 2.5” TFT LCD SUPPORTS TYPE RESOLUTION DATA WIDTH DESCRIPTION CASIO COM25T2171 480x240 8-bit J8 J8 VCOM GND GPIO30 GPIO31 GPIO32 GPIO33 GPIO34 GPIO35 GPIO36 GPIO37 GPIO38 GPIO39 GPIO40 GPIO41 RP10 1 2 3 4 1 2 3 4 RP11 1 2 3 4 RP12 8P4R-22 8 7 6 5 8 7 6 5 8 8P4R-22 7 6 5 8P4R-22 VCLK VDEN VSYNC HSYNC VD0 VD1 VD2 VD3 VD4 VD5 VD6 VD7 POCB VDEN SFRM SSPTXD SCLK VSYNC HSY NC VCLK VD7 VD6 VD5 VD4 VD3 VD2 VD1 VD0 VBC VSH COMDC LCDVDD VGH VDC CB31 CB33 1uF VGL 1uF COMOUT VVCOM GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 VCOM VSS TEST POCB BLON CS DI SCK VSYNC HSY NC CLK D7 D6 D5 D4 D3 D2 D1 D0 VBC VSH COMDC VDD VGH VDC1 C2+ C2VGL C1C1+ COMOUT VVCOM VSS COM25T2171T - 21 - Publication Release Date: Apr 6, 2009 Revision: E NUC710 EVB USER MANUAL 3.6.2 AUO 3” TFT LCD module SUPPORTS TYPE RESOLUTION DATA WIDTH DESCRIPTION AUO A030DL01 960x240 RGB 8-bit J1 of module board RP1 GPIO11 GPIO12 GPIO13 RP2 1 2 3 4 SFRM SSPTXD SCLK 8 7 6 5 GPIO30 GPIO31 GPIO32 GPIO33 GPIO34 GPIO35 GPIO36 GPIO37 GPIO38 GPIO39 GPIO40 GPIO41 8P4R-22 CON1 VDD GPIO51 GPIO49 GPIO47 GPIO45 GPIO43 GPIO20 GPIO22 GPIO24 GPIO26 GPIO28 nRESET GPIO3 GPIO1 GPIO34 GPIO36 GPIO38 GPIO40 GPIO33 GPIO31 GPIO14 GPIO12 GPIO10 GPIO8 GND 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 VDD GPIO50 GPIO48 GPIO46 GPIO44 GPIO42 GPIO21 GPIO23 GPIO25 GPIO27 GPIO29 GPIO4 GPIO2 GPIO0 GPIO35 GPIO37 GPIO39 GPIO41 GPIO32 GPIO30 GPIO13 GPIO11 GPIO9 GPIO7 GND 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 1 2 3 4 1 2 3 4 1 2 3 4 RP3 RP4 8P4R-22 8 7 6 5 8 7 6 5 8 8P4R-22 7 6 5 8P4R-22 J1 VCLK VDEN VSY NC HSY NC VD0 VD1 VD2 VD3 VD4 VD5 VD6 VD7 V3 V1 + C1 + C2 4.7uF/10V 4.7uF/10V V2 V4 V5 VCOMH VGH V7 + C3 + C4 + C5 4.7uF/10V 4.7uF/10V 4.7uF/10V + C6 4.7uF/10V V6 V8 VCOML VGL V9 + C7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 SFRM SSPTXD SCLK HSY NC VSY NC VCLK VD7 VD6 VD5 VD4 VD3 VD2 VD1 VD0 DRV BLH BLL AVDD VDD33 V1 V2 V3 V4 V5 V6 V7 V8 V9 V10 + C8 4.7uF/10V 4.7uF/10V VGL VGH VCOML VCOMH + C9 4.7uF/10V V10 I/O EXT. CON VDD VCOM CS SDA SCL HSY NC VSY NC DCLK D7 D6 D5 D4 D3 D2 D1 D0 DRV VLED FB AVDD AGND GND VCCI VDC V1 V2 V3 V4 V5 V6 V7 V8 V9 V10 FRP VGL VGH VCOML VCOMH VCOM N.C. AUO 3.0" TFT A030DL01 L1 D1 6.8uH U1 RT9164A-3.3v BLH BLL MBR0520 IN GND OUT R1 + C11 AVDD + 4 2 VDD EN VSS LX OVP FB L2 FB VDD33 VDD U2 6 EN VDD33 VDD 3 1 2 22 4.7uF/10V C12 4.7uF/10V +3.3V 1A 4 C10 33uF/16V OUT VDD AVDD 1 5 CB2 C14 3 C13 33uF/16V CB1 0.1uF 33uF/16V C15 0.1uF 10uF/16V PC113 R2 3.3 VDD L3 CB3 CB4 1uF 1uF R3 0 EN R4 0 DRV NOP LCD BACKLIGHT - 22 - GND FB NUC710 EVB USER MANUAL 3.7 Keypad Interface SUPPORTS TYPE OUTPUT SIGNALS INPUT SIGNALS DESCRIPTION 2x8 Matrix KPI_ROW[0-1] KPI_COL[0-7] BP1-BP16 BP2 1 2 COL3 2 COL2 COL1 COL0 BP1 1 BP3 1 2 BP4 1 2 ROW0 VDD33 PUSH-KEY BP5 1 PUSH-KEY BP6 2 1 PUSH-KEY BP10 1 PUSH-KEY BP13 1 2 1 2 2 1 PUSH-KEY 1 2 1 ROW1 BP12 1 PUSH-KEY BP15 PUSH-KEY 2 PUSH-KEY BP11 PUSH-KEY BP14 PUSH-KEY 3.8 2 PUSH-KEY BP8 COL7 2 1 COL6 1 2 PUSH-KEY COL5 COL4 BP9 PUSH-KEY BP7 2 ROW0 COL0 COL1 COL2 COL3 RP20 5 6 7 8 8P4R-22 4 3 2 1 COL4 COL5 COL6 COL7 RP21 5 6 7 8 8P4R-22 4 3 2 1 PUSH-KEY BP16 2 1 PUSH-KEY 2 ROW1 PUSH-KEY JTAG Interface SUPPORTS TYPE IN/OUT SIGNALS DESCRIPTION JTAG Interface TDO,TDI,TMS,TCK,nTRST,nSRST CON4 JTAG CON VDD33 R1 10K nSRST R2 CON4 2 4 6 8 10 12 14 0 1 3 5 7 9 11 13 8P4R-10K RP1 5 6 7 8 4 3 2 1 nTRST TDI TMS TCK TDO JTAG-14 - 23 - Publication Release Date: Apr 6, 2009 Revision: E NUC710 EVB USER MANUAL 3.9 Ethernet INTERFACE TYPE IN/OUT SIGNALS DESCRIPTION RMII RMII interface Physical layer supported by DM9161A Please notice that NUC710 Ethernet MAC port can only supports RMII interface, don’t supports MII interface PHYceiver. - 24 - NUC710 EVB USER MANUAL 3.10 RTC NUC710 integrated RTC function and it needed 1.8V voltage to supply the RTC internal circuit. The development board has two ways to supply the power for RTC, one from onboard 3.3V->1.8V LDO regulator RT9161 (mount R7) and the other way from external power source via RTCVDD pin (mount R10). 1.8V VOLTAGE for RTC RTC1V8 R7 0 R10 0 CVDD18 RTCVDD Optional CB16 0.1uF 3.11 SPI Interface NUC710 integrated SPI interface and connected to a WINBOND serial flash in this application board. Please see the following schematic for more detail. VDD33 R6 1K nHOLD R7 1K nWP U4 NF_CS NF_DO nWP GND 1 2 3 4 CS DO WP GND SPI-FLASH VCC HOLD CLK DI 8 7 6 5 VDD33 nHOLD NF_CLK NF_DI W25P10/20/40 NexFLASH(SPI) - 25 - Publication Release Date: Apr 6, 2009 Revision: E NUC710 EVB USER MANUAL 3.12 Timer output NUC710 integrated timer output function and the development board connected two timer-out signals to LED display. Please see the following schematic for more detail. TIMER OUTPUT VDD33 VDD33 TIMER0 OUTPUT TIMER1 OUTPUT R8 R9 1 220 1 220 LED_R LED_R R10 3.3k TIMER0 R11 Q2 2N3904 3.3k TIMER1 2 1 2 1 Q1 2N3904 32 LED2 32 LED1 3.13 I2C NUC710 integrated I2C interface and connected the SCL and SDA signals to a serial EEPROM which addressed at 0x0H. Please see the following schematic for more detail. VDD33 I2C EEPROM ADDRESS:0H 0.1uF R4 R5 1K 2.2K 2.2K U3 I2C-EEPROM VDD33 CB4 R3 1 2 3 4 A0 A1 A2 GND VCC WP SCL SDA 8 7 6 5 24LC64 - 26 - SCL SDA NUC710 EVB USER MANUAL 3.14 SD card interface NUC710 integrated SD memory card interface and connected to a SD card slot in this application board. It used a power switch controlled by SD_PWR signal to control the SD card power on/off. Please see the following schematic for more detail. NOP VDD33 SD_WP R81 SD_PWR nXDACK SD_VDD33 SI2301SD Q3 LL5 33 CB6 + HOLD CB5 0.1uF GND WP CB7 DAT1 DAT0 VSS CLK VDD VSS CMD DAT3 DAT2 1uF VDD33 FB J2 15 R18 0 0.1uF C3 + 14 HOLD 10uF/16V GND CD# 11 10 8 7 6 5 4 3 2 1 9 12 13 SD_WP SD_DAT1 SD_DAT0 SD_CLK SD_CMD SD_DAT3 SD_DAT2 SD_CD SD/MMC SOCKET 3.15 Ext. DMA interface NUC710 supports external DMA request function for external device. The development board connected the nXDACK and nXDREQ signals to connector J1. Please connect the external DMA Request/Ack signal to the interface. - 27 - Publication Release Date: Apr 6, 2009 Revision: E NUC710 EVB USER MANUAL VDD33 R16 4.7K R17 4.7K J1 nXDACK nXDREQ 1 2 1 2 1X2_HEADER_2.54 - 28 - NUC710 EVB USER MANUAL 3.16 SMC interface NUC710 integrated smart card controller and the application board connected the interface to a smart card slot and a SIM type socket. The smart card port0 connected with an external level-shifter to support 5V and 3V card. The smart card port1 interface connected to card directly but can only supports 3V SIM type smart card because the NUC710 I/O voltage is 3.3V level. Please refer to the following schematic for more detail. SMART CARD0 Vcc R19 10K CLK VDD M0 0 0 1 1 Vcc R20 10K R21 10K DAT RST R22 JP8 VDD33 3V/5V GND VDD33 U5 VDD33 GND 3V/5V SC0_PWR Vcc=VIN Vcc=3V Vcc=5V J3 10 9 CB8 0.1uF 10K SHUT DOWN SC0_PRES 3V/5V SEL R23 OPERATING MODE 10K 1 2 3 SC0_CLK SC0_RST SC0_DAT M1 0 1 0 1 1 2 3 4 5 6 7 8 CIN RIN DATA DDRV DVcc SS M1 M0 SLK RST I/O Vcc VIN C1+ C1GND 16 15 14 13 12 11 10 9 4 3 2 1 CLK RST DAT Vcc VDD33 CB10 0.1uF S2 S1 C4 C3 C2 C1 VDD33 C8 C7 C6 C5 8 7 6 5 DAT + C4 CB9 10uF/16V 0.1uF SCSLOT C5 10uF/16V LTC1555L VDD33 SC1_Vcc SMART CARD1 SC1_PWR SI2301SD Q4 10K SC1_Vcc R25 10K R26 10K R27 10K SC1_CLK SC1_Vcc SC1_RST SC1_CLK CB11 0.1uF R24 SC1_DAT J4 1 2 3 4 C1 C2 C3 C4 C5 C6 C7 C8 5 6 7 8 GND SC1_RST SC1_DAT SC1_PRES SIM Card Slot - 29 - Publication Release Date: Apr 6, 2009 Revision: E NUC710 EVB USER MANUAL 3.17 GPIO TEST interface The evaluation board reserved GPIO expansion interface for system development and testing. Please see the following connector pin arrangement for more detail. CON10 VDD GPIO51 GPIO49 GPIO47 GPIO45 GPIO43 GPIO20 GPIO22 GPIO24 GPIO26 GPIO28 nRESET GPIO3 GPIO1 GPIO34 GPIO36 GPIO38 GPIO40 GPIO33 GPIO31 GPIO14 GPIO12 GPIO10 GPIO8 GND 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 I/O TEST CON - 30 - VDD GPIO50 GPIO48 GPIO46 GPIO44 GPIO42 GPIO21 GPIO23 GPIO25 GPIO27 GPIO29 GPIO4 GPIO2 GPIO0 GPIO35 GPIO37 GPIO39 GPIO41 GPIO32 GPIO30 GPIO13 GPIO11 GPIO9 GPIO7 GND NUC710 EVB USER MANUAL 3.18 EBI interface The evaluation board reserved EBI expansion interface for system expansion and testing. Please see the following connector pin arrangement for more detail. CON1 VDD A0 A2 A4 A6 A8 A10 A12 A14 A16 A18 A20 nECS2 nECS1 nOE nWBE0 SDD15 SDD13 SDD11 SDD9 SDD7 SDD5 SDD3 SDD1 nIRQ0 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 VDD nRESET A1 A3 A5 A7 A9 A11 A13 A15 A17 A19 A21 nECS0 nWAIT nWBE1 SDD14 SDD12 SDD10 SDD8 SDD6 SDD4 SDD2 SDD0 GND EBI TEST CON CON3 GND SDD30 SDD28 SDD26 SDD24 nECS3 nWBE2 nIRQ2 SDD22 SDD20 SDD18 SDD16 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 GND SDD31 SDD29 SDD27 SDD25 nWBE3 nIRQ3 SDD23 SDD21 SDD19 SDD17 VDD EBI TEST CON - 31 - Publication Release Date: Apr 6, 2009 Revision: E NUC710 EVB USER MANUAL 3.19 LED display This board has 8-LED displays controlled by EBI bank0 with latch buffers for system development and testing. Please see the following schematic for more detail. - 32 - NUC710 EVB USER MANUAL 4. SCHEMATIC 4.1 Core Module board NUC710 CORE MODULE nWBE[3..0] SDD[31..0] AD[21..0] NUC710 MEM EBI EXT. INTERFACE AD[21..0] SDD[31..0] nWBE[3..0] nSWE nOE nBTCS nSRAS nSCAS SDMCLK MCKE nSCS0 nRESET nSWE nOE nBTCS nSRAS nSCAC SDMCLK MCKE nSCS0 AD[21..0] SDD[31..0] nWBE[3..0] nSWE nOE nBTCS nSRAS nSCAS SDMCLK MCKE nSCS0 nECS[3..0] nECS[3..0] nWAIT nWAIT nIRQ[3..2] nIRQ0 nIRQ[3..2] nIRQ0 AD[21..0] SDD[31..0] nECS[3..0] nWBE[3..0] nOE nWAIT nIRQ[3..2] nIRQ0 nRESET nRESET EBI EXT. INTERFACE MEM.sch UART TXD0 RXD0 TXD0 RXD0 nTXD0 nRXD0 I/O EXT. INTERFACE UART.sch USB USB_FLAG USB_ON/OFF DP0 DN0 DP1 DN1 nRESET USB_FLAG USB_ON/OFF DP0 DN0 DP1 DN1 USB_FLAG USB_ON/OFF DP0 DN0 DP1 DN1 GPIO[4..0] GPIO[10..7] GPIO[14..11] GPIO[29..20] GPIO[41:30] GPIO[51..42] GPIO[4..0] GPIO[10..7] GPIO[14..11] GPIO[29..20] GPIO[41..30] GPIO[51..42] GPIO[4..0] GPIO[10..7] GPIO[14..11] GPIO[29..20] GPIO[41..30] GPIO[51..42] nRESET USB.sch JTAG&RESET I/O EXT. INTERFACE TMS TDI TDO TCK nTRST nRESET TMS TDI TDO TCK nTRST TMS TDI TDO TCK nTRST nRESET POWER JTAG&RESET.sch POWER.sch NUC710.sch Title NUC710 core module Size A Date: - 33 - Document Number <Doc> Monday , April 06, 2009 Rev <Rev Code> Sheet 1 of 9 Publication Release Date: Feb 12, 2007 Revision: D NUC710 EVB USER MANUAL SDD[31..0] AD[21..0] nWBE[3..0] nECS[3..0] nOE nRESET SDD[31..0] AD[21..0] nWBE[3..0] nWAIT nIRQ[3..2] nIRQ0 nWAIT nIRQ[3..2] nIRQ0 nECS[3..0] nOE nRESET CON1 VDD AD0 AD2 AD4 AD6 AD8 AD10 AD12 AD14 AD16 AD18 AD20 nECS2 nECS1 nOE nWBE0 SDD15 SDD13 SDD11 SDD9 SDD7 SDD5 SDD3 SDD1 nIRQ0 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 VDD nRESET AD1 AD3 AD5 AD7 AD9 AD11 AD13 AD15 AD17 AD19 AD21 nECS0 nWAIT nWBE1 SDD14 SDD12 SDD10 SDD8 SDD6 SDD4 SDD2 SDD0 GND CON2 RTCVDD RTCVDD SDD30 SDD28 SDD26 SDD24 nECS3 nWBE2 nIRQ2 SDD22 SDD20 SDD18 SDD16 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 GND SDD31 SDD29 SDD27 SDD25 nWBE3 nIRQ3 SDD23 SDD21 SDD19 SDD17 VDD EBI ADDRESS EXT. CON EBI EXT. CON VDD C1 33uF/16V Title <Title> Size A Date: - 34 - Document Number <Doc> 星星星, 十十十 08, 2005 Rev <Rev Code> Sheet 2 of 9 NUC710 EVB USER MANUAL GPIO[10..7] GPIO[14..11] GPIO[41..30] GPIO[4..0] GPIO[29..20] GPIO[51..42] nRESET GPIO[10..7] GPIO[14..11] GPIO[41..30] GPIO[4..0] GPIO[29..20] GPIO[51..42] GPIO[10..7]----->UART1_2,PS/2 GPIO[14..11]---->I2C,SSP GPIO[41..30]---->LCD,KPI GPIO[4..0]------>AC-97,I2S,PWM,UART3 GPIO[29..20]---->SD,SMC,LCD HIGH BITS GPIO[51..42]---->ETHERNET PHY,KPI,LCD HIGH BITS nRESET CON3 VDD GPIO51 GPIO49 GPIO47 GPIO45 GPIO43 GPIO20 GPIO22 GPIO24 GPIO26 GPIO28 nRESET GPIO3 GPIO1 GPIO34 GPIO36 GPIO38 GPIO40 GPIO33 GPIO31 GPIO14 GPIO12 GPIO10 GPIO8 GND 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 VDD GPIO50 GPIO48 GPIO46 GPIO44 GPIO42 GPIO21 GPIO23 GPIO25 GPIO27 GPIO29 GPIO4 GPIO2 GPIO0 GPIO35 GPIO37 GPIO39 GPIO41 GPIO32 GPIO30 GPIO13 GPIO11 GPIO9 GPIO7 GND VDD C2 33uF/16V I/O EXT. CON Title <Title> Size A Date: - 35 - Document Number <Doc> 星星星, 十十十 08, 2005 Rev <Rev Code> Sheet 3 of 9 Publication Release Date: Feb 12, 2007 Revision: D NUC710 EVB USER MANUAL TMS TDI nTRST TMS TDI nTRST JTAG CON VDD33 TCK TDO TCK TDO R1 8P4R-10K RP1 5 6 7 8 R2 10K CON4 2 4 6 8 10 12 14 nSRST 0 4 3 2 1 1 3 5 7 9 11 13 nTRST TDI TMS TCK TDO JTAG-14 VDD33 CB1 0.1uF RESET circuit VDD VDD R3 R4 10K 1 U2 VDD SP1 10K U1A nSRST 2 1 4 6 VCC MR PFI WDI 3 RESET WDO PFO GND 7 8 5 3 nRESET 2 74LS08 VDD SP705 CB2 SW PUSHBUTTON 0.1uF Title <Title> Size A Date: - 36 - Document Number <Doc> 星星星, 十十十 08, 2005 Rev <Rev Code> Sheet 4 of 9 NUC710 EVB USER MANUAL SDD[0..31] AD[0..21] nWBE[0..3] nSWE nOE nBTCS nSRAS nSCAS SDMCLK MCKE nSCS0 nRESET SDD[0..31] AD[0..21] nWBE[0..3] nSWE nOE nBTCS nSRAS nSCAS SDMCLK MCKE nSCS0 nRESET BOOT FLASH SDRAM FA21=VDD_F for WINBOND FLASH FA21=A21 for AMD FLASH Default:AMD Flash W986416AH 1M x16 x 4 BANKs W981216AH 2M x16 x 4 BANKs W982516AH 4M x16 x 4 BANKs AD21 FA21 R5 0 R6 4.7K VDD33 U3 SDD0 SDD1 SDD2 SDD3 SDD4 SDD5 SDD6 SDD7 SDD8 SDD9 SDD10 SDD11 SDD12 SDD13 SDD14 SDD15 2 4 5 7 8 10 11 13 42 44 45 47 48 50 51 53 nWBE0 nWBE1 nSWE nSCAS nSRAS nSCS0 AD13 AD14 15 39 16 17 18 19 20 21 VDD33 43 9 3 49 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQML DQMH /WE /CAS /RAS /CS BA0 BA1 U4 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12 CLK CKE VSS VSS VSS VSSQ VSSQ VSSQ VSSQ NC VDDQ VDDQ VDDQ VDDQ VDD VDD VDD 23 24 25 26 29 30 31 32 33 34 22 35 36 38 37 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 AD8 AD9 AD10 AD11 AD12 SDMCLK MCKE SDD16 SDD17 SDD18 SDD19 SDD20 SDD21 SDD22 SDD23 SDD24 SDD25 SDD26 SDD27 SDD28 SDD29 SDD30 SDD31 28 41 54 6 12 46 52 nWBE2 nWBE3 nSWE nSCAS nSRAS nSCS0 AD13 AD14 40 27 14 1 2 4 5 7 8 10 11 13 42 44 45 47 48 50 51 53 VDD33 VDD33 15 39 16 17 18 19 20 21 43 9 3 49 W986416EH DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQML DQMH /WE /CAS /RAS /CS BA0 BA1 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10/AP A11 A12 CLK CKE VSS VSS VSS VSSQ VSSQ VSSQ VSSQ VDDQ VDDQ VDDQ VDDQ NC VDD VDD VDD AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 AD8 AD9 AD10 AD11 AD12 SDMCLK MCKE 23 24 25 26 29 30 31 32 33 34 22 35 36 38 37 NOP AD15 AD14 AD13 AD12 AD11 AD10 AD9 AD8 AD19 AD20 nWBE1 nRESET FA21 VDD33 28 41 54 6 12 46 52 AD18 AD17 AD7 AD6 AD5 AD4 AD3 AD2 AD1 40 VDD33 27 14 1 A15 A14 A13 A12 A11 A10 A9 A8 A19 A20 WE RESET# VPP WP# RY /BY # A18 A17 A7 A6 A5 A4 A3 A2 A1 A16 BY TE# VSS DQ15/A-1 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# VSS CE# A0 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 AD16 VDD33 GND SDD15 SDD7 SDD14 SDD6 SDD13 SDD5 SDD12 SDD4 VDD33 SDD11 SDD3 SDD10 SDD2 SDD9 SDD1 SDD8 SDD0 nOE GND nBTCS AD0 W19B/L320S W986416EH VDD33 U5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 1,2,4MB(up to 8MB AMD FLASH) VDD33 am29LV800B 512Kx16 am29LV160D 1Mx16 am29LV320D 2Mx16 VDD33 VDD33 CB3 CB4 CB5 CB6 CB7 CB8 CB9 CB10 CB11 C3 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 22uF/10V W19B/L320S 2Mx16 Title <Title> Size A Date: - 37 - Document Number <Doc> 星星星, 十十十 08, 2005 Rev <Rev Code> Sheet 5 of 9 Publication Release Date: Feb 12, 2007 Revision: D NUC710 EVB USER MANUAL CON5 OUT IN GND OUT U6 AMC1117-3.3v VDD33 +3.3V 1A 1 LL2 USBVDD FB CVDD33 CB14 LL3 CB12 C4 0.1uF 22uF/10V CAP1 Power JACK C5 33uF/16V 2 3 LL1 FB GND GND IN 4 3 1 2 VDD CB13 0.1uF 100uF/16V 0.1uF FB +1.8V 100mA GND CVDD18 U7 1 2 3 CB15 Vin Vout GND EN BP C6 5 LL4 C7 C8 22uF/10V 22uF/10V CD1 RT9193-1.8v 0.1uF AVDD18 FB 4 22uF/10V 22nF 1.8V VOLTAGE for RTC R7 R10 RTC1V8 0 0 Power LEDs RED_LED 2 RED_LED 2 CVDD18 LED1 1 R8 220 1 R9 220 LED2 CVDD18 CVDD33 RTCVDD Optional CB16 0.1uF Title <Title> Size A Date: - 38 - Document Number <Doc> 星星星, 十十十 08, 2005 Rev <Rev Code> Sheet 6 of 9 NUC710 EVB USER MANUAL RXD0 VDD33 GREEN_LED LED3 RXD0 2 1 R11 1K GREEN_LED LED4 TXD0 2 1 R12 1K Console UART(TX/RX only) CON6 CC1 + RXD0 TXD0 VDD UTXD CC3 1uF/16V + CC4 1uF/16V + CC5 1uF/16V U8 + 1 2 3 4 5 6 7 8 C1+ V+ C1C2+ C2VT2_OUT R2_IN VCC GND T1_OUT R1_IN R1_OUT T1_IN T2_IN R2_OUT 16 15 14 13 12 11 10 9 CC2 1uF/16V URXD + TXD0 1uF/16V GND UTXD URXD RXD0 TXD0 1 6 2 7 3 8 4 9 5 DSUB-9 FeMale Female and Male are use difference pin define!!! SP232ECA Title <Title> Size A Date: - 39 - Document Number <Doc> 星星星, 十十十 08, 2005 Rev <Rev Code> Sheet 7 of 9 Publication Release Date: Feb 12, 2007 Revision: D NUC710 EVB USER MANUAL DP0 DN0 DP1 DN1 D1+ D1D2+ D2- USBVDD USBVDD USB HOST C9 R13 33uF/16V U9 LL5 10K USB_ON/OFF USB_FLAG USB_ON/OFF USB_FLAG R14 1 2 3 4 10K 8 7 6 5 CTL1 OUT1 FLG1 IN FLG2 GND CTL2 OUT2 1 CB17 C10 0.1uF R15 CON7 FB D1D1+ CD2 33uF/16V 2 3 4 0.01uF AMC3526H VBUS DD+ GND USB A-TY PE FB 10K LL6 R16 R17 15K 15K NOP USBVDD R18 USB Device 0 CON8 U1B R19 4 1.5K 6 nRESET nRESET 1 2 3 4 5 D2D2+ 5 74LS08 FB VBUS DD+ NC GND LL7 mimi USB B-TY PE Title <Title> Size A Date: - 40 - Document Number <Doc> 星星星, 十十十 08, 2005 Rev <Rev Code> Sheet 8 of 9 NUC710 EVB USER MANUAL MCLK 5 6 7 8 5 6 7 8 5 6 7 8 5 6 7 8 4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 8P4R-22 D16 D17 D18 D19 8P4R-22 D20 D21 D22 D23 8P4R-22 D24 D25 D26 D27 8P4R-22 D28 D29 D30 D31 nWAIT nOE nECS0 nECS1 nECS2 CVDD33 GND nECS3 D24 D25 D26 D27 CVDD33 D28 D29 D30 D31 A21 GND A20 A19 A18 A17 CVDD18 A16 A15 A14 GND A13 A12 A11 A10 CVDD33 A9 A8 A7 A6 A5 GND A4 A3 A2 A1 A0 SDD16RP6 SDD17 SDD18 SDD19 SDD20RP7 SDD21 SDD22 SDD23 SDD24RP8 SDD25 SDD26 SDD27 SDD28RP9 SDD29 SDD30 SDD31 A[0..21] nECS[3..0] U10 nBTCS MCKE nSCS0 nSRAS nSCAS CVDD33 MCLK GND nSWE nWBE0 nWBE1 nWBE2 nWBE3 nIRQ2 nIRQ3 D23 D22 D21 D20 D19 D18 D17 D16 GND D15 D14 CVDD18 D13 D12 D11 D10 CVDD33 D9 D8 D7 D6 D5 GND D4 D3 D2 D1 D0 nWBE[3..0] TXD0 RXD0 nTXD0 nRXD0 nIRQ[3..2] UART0 USB_DP0 USB_DN0 USB_DP1 USB_DN1 USB_ON/OFF USB_FLAG AD[0..21] R21 27 R22 R23 27 27 R24 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 DP0 DN0 DP1 DN1 27USB_PWREN nIRQ1 USB interface GP[4..0] GP[10..7] GP[14..11] GP[29..20] GP[41..30] GP[51..42] GPIO[4..0] GPIO[10..7] GPIO[14..11] GPIO[29..20] GPIO[41:30] GPIO[51..42] RP10 5 6 7 8 RP11 5 6 7 8 RP12 5 6 7 8 RP13 5 6 7 8 4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 AD16 RP14 5 AD17 6 AD18 7 AD19 8 AD20 AD21 R25 R26 EXT. I/O interface 8P4R-22 A0 A1 A2 A3 8P4R-22 A4 A5 A6 A7 8P4R-22 A8 A9 A10 A11 8P4R-22 A12 A13 A14 A15 4 8P4R-22 A16 A17 3 A18 2 A19 1 A20 A21 22 22 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 Power-ON settings CVDD33 5 6 7 8 nBTCS MCKE nSCS[0] nSCS[1] nSRAS nSCAS VDD33 MCLK VSS33 nWE nWBE[0]/SDQM[0] nWBE[1]/SDQM[1] nWBE[2]/SDQM[2]/GP[69] nWBE[3]/SDQM[3]/GP[68] nIRQ[2]/GP[18] nIRQ[3]/GP[19] D[23]/VD15]/GP[59] D[22]/VD[14]/GP[58] D[21]/VD[13]/GP[57] D[20]/VD[12]/GP[56] D[19]/VD[11]/GP[55] D[18]/VD[10]/GP[54] D[17]/VD[9]/GP[53] D[16]/VD[8]/GP[52] VSS18 D[15] D[14] VDD18 D[13] D[12] D[11] D[10] VDD33 D[9] D[8] D[7] D[6] D[5] VSS33 D[4] D[3] D[2] D[1] D[0] NUC710 SDD8 SDD9 4 3 2 1 CVDD33 SDD12 CD3 R27 JP1 EXTAL_15M SDD15 RP15 8P4R-4.7K R29 4.7K R30 4.7K TEST SDD13 20pF 22 R28 4.7K R31 X1 80MHZ 1 2 3 15MHZ USB UART0 CVDD33 JP2 20pF SDD14 R33 NOP CD5 R33 0 nIRQ2 INT BUTTON R34 0 nIRQ3 R32 4.7K EXTAL_32.768K LITTLE 1 2 3 JTAG CB19 0.1uF 0.1uF RTCVDD USBVDD TP1 5V 1 USBVDD TEST POINT TP2 C15 GND AVDD18 1 20pF 22uF/10V USBGND R35 X2 CVDD33 10M CD6 R36 XTAL_15M EXTAL_15M GND USB_PWREN nTRST TCK TDO TDI TMS BIG 15M/80M GREEN_LED LED5 STATUS LED 2 1 CB18 32.768KHz Cry stal XTAL_32.768K TEST POINT AVDD18 STATUS LED GP[42..51] GP51 GP50 GP49 CVDD33 GP48 GP47 GP46 GP45 GND GP44 GP43 GP[29..20] GP42 GP20 GP21 GP22 GND GP23 GP24 GP25 CVDD33 GP26 GP27 GP28 GP29 GND GP[4..0] CVDD18 GP4 GP3 GP2 GP1 GP0 XTAL_32.768K EXTAL_32.768K RTC1V8 RTC1V8 CVDD33 USBVDD 15M/80M 15MHz Cry stal XTAL_15M 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 RTCVDD 1M CD4 NUC710 PHY _MDC/GP[51]/KPI_ROW[1] PHY _MDIO/GP[50]/KPI_ROW[0] PHY _TXD[1]/GP[49]/KPI_COL[7] VDD33 PHY _TXD[0]/GP[48]/KPI_COL[6] PHY _TXEN/GP[47]/KPI_COL[5] PHY _REFCLK/GP[46]/KPI_COL[4] PHY _RXD[1]/GP[45]/KPI_COL[3] VSS PHY _RXD[0]/GP[44]/KPI_COL[2] PHY _CRSDV/GP[43]/KPI_COL[1] PHY _RXERR/GP[42]/KPI_COL[0] SC1_PWR/nXDACK/GP[20] SC1_PPES/nXDREQ/GP[21] SC1_RST/SD_CD/GP[22] VSS33 SC1_CLK/SD_PWR/GP[23] SC1_DAT/SD_DAT3/GP[24] SC0_PWR/SD_DAT2/GP[25] VDD33 SC0_PRES/SD_DAT1/GP[26] SC0_RST/SD_DAT0/GP[27] SC0_CLK/SD_CLK/GP[28] SC0_DAT/SD_CMD/GP[29] VSS18 VDD18 AC97_BITCLK/I2S_BITCLK/PWM[3]/RXD3/GP[4] AC97_SY NC/I2S_LRCLK/PWM[2]/TXD3/GP[3] AC97_DATO/I2S_DATO/PWM[1]/DSR3/GP[2] AC97_DATI/IS2_DATI/PWM[0]/DTR3/GP[1] AC97_nRESET/I2S_MCLK/GP[0]/nIRQ4 XTAL(32.768K) EXTAL(32.768K) RTCVDD18 VDD33 XTAL(15M) EXTAL(15M) VSS33 nWDOG/GP[15]/USB_PWREN nTRST TCK TDO TDI TMS GP[41..30] JTAG interface 8P4R-22 D0 D1 D2 D3 8P4R-22 D4 D5 D6 D7 8P4R-22 D8 D9 D10 D11 8P4R-22 D12 D13 D14 D15 GP[14..11] TMS TDI TDO TCK nTRST TMS TDI TDO TCK nTRST 4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 GP[10..7] EBI interface 5 6 7 8 5 6 7 8 5 6 7 8 5 6 7 8 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 099 098 097 096 095 094 093 092 091 090 089 nECS[3..0] AD[21..0] SDD[31..0] nOE nWBE[3..0] nIRQ0 nIRQ[3..2] nWAIT nRESET nECS[3..0] AD[21..0] SDD[31..0] nOE nWBE[3..0] nIRQ0 nIRQ[3..2] nWAIT nRESET SDD0 RP2 SDD1 SDD2 SDD3 SDD4 RP3 SDD5 SDD6 SDD7 SDD8 RP4 SDD9 SDD10 SDD11 SDD12RP5 SDD13 SDD14 SDD15 nWAIT/nIRQ5 nOE nECS[0] nECS[1] nECS[2] VDD33 VSS33 nECS[3] D[24]/VD[16]/GPIO[60] D[25]/VD[17]GPIO[61] D[26]/VD[18]/GPIO[62] D[27]/VD[19]/GPIO[63] VDD33 D[28]/VD[20]/GPIO[64] D[29]/VD[21]/GPIO[65] D[30]/VD[22]/GPIO[66] D[31]/VD[23]/GPIO[67] A[21] VSS33 A[20] A[19] A[18] A[17] VDD18 A[16] A[15] A[14] VSS18 A[13] A[12] A[11] A[10] VDD33 A[9] A[8] A[7] A[6] A[5] VSS33 A[4] A[3] A[2] A[1] A[0] nSCS0 MCKE nSWE nSCAS nSRAS nBTCS USB1VDD DP1 DN1 USB1VSS USB0VSS DN0 DP0 USB0VDD VDD33 TXD0/GP[5] RXD0/GP[6] TXD1/GP[7] RXD1/GP[8] CTS1/TXD2/PS2_CLK/GP[9] RTS1/RXD2/PS2_DAT/GP[10] VSS33 SCL0/SRFM/TIMER0/GP[11] SDA0/SSPTXD/TIMER1/GP[12] SCL1/SCLK/GP[13] SDA1/SSPRXD/GP[14] VDD18 VSS18 KPI_ROW[0]/VCLK/GP[30] KPI_ROM[1]/VDEN/GP[31] KPI_ROM[2]/VSYNC/GP[32] KPI_ROW[3]/HSYNC/GP[33] KPI_COL[7]/VD[7]/GP[41] KPI_COL[6]/VD[6]/GP[40] KPI_COL[5]/VD[5]/GP[39] KPI_COL[4]/VD[4]/GP38] KPI_COL[3]/VD[3]/GP[37] KPI_COL[2]/VD[2]/GP[36] KPI_COL[1]/VD[1]/GP[35] KPI_COL[0]/VD[0]/GP[34] VDD33 VSS33 nRESET TEST PLL0VDD18 PLL0VSS18 PLL1VSS18 PLL1VDD18 nIRQ[0]/GP[16] nIRQ[1]/GP[17] SDD[0..31] 22 nSCS0 MCKE nSWE nSCAS nSRAS nBTCS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 R20 USBVDD DP1 DN1 USBGND USBGND DN0 DP0 USBVDD CVDD33 TXD0 RXD0 GP7 GP8 GP9 GP10 GND GP11 GP12 GP13 GP14 CVDD18 GND GP30 GP31 GP32 GP33 GP41 GP40 GP39 GP38 GP37 GP36 GP35 GP34 CVDD33 GND nRESET TEST AVDD18 AVSS18 AVSS18 AVDD18 nIRQ0 nIRQ1 SDMCLK TP3 GND 1 1K TEST POINT 20pF INT BUTTON R37 1K CVDD33 SP2 C11 CB20 CB21 CB22 CB23 CB24 CB25 CB26 CB27 CB28 C12 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 22uF/10V C13 C14 CB29 CB30 CB31 CB32 LL8 0.1uF 0.1uF 0.1uF 0.1uF LL9 SW PUSHBUTTON 22uF/10V Publication Release Date: Feb 12, 2007 Revision: D CVDD18 - 41 22uF/10V 22uF/10V USBGND FB AVSS18 FB GND Title NUC710 core module Size B Date: Document Number <Doc> Monday , April 06, 2009 Rev <Rev Code> Sheet 9 of 9 NUC710 EVB USER MANUAL 4.2 Application board FUNCTION BLOCK EBI EXT. INTERFACE GPIO[4..0] EBI ECS0 GPIO[4..0] SDD[0..7] nECS1 SDD[0..7] nECS0 SDD[0..7] nECS0 GPIO[4..0].sch GPIO[10..7] GPIO[10..7] EBI ECS0.SCH GPIO[10..7].sch GPIO[14..11] SCLK SFRM SSPTXD SSPRXD EBI EXT. INTERFACE I/O EXT. INTERFACE GPIO[4..0] GPIO[10..7] GPIO[14..11] GPIO[14..11] GPIO[29..20] GPIO[41..30] GPIO[51..42] GPIO[14..11].sch GPIO[29..20] GPIO[4..0] GPIO[10..7] GPIO[14..11] GPIO[29..20] GPIO[41..30] GPIO[51..42] nRESET GPIO[29..20] I/O EXT. INTERFACE GPIO[29..20].sch GPIO[41..30] SCLK SFRM SSPTXD SSPRXD GPIO[41..30] GPIO[41..30].sch GPIO[51..42] POWER GPIO[51..42] nRESET POWER GPIO[51..42].sch Title <Title> Size A Date: - 42 - Document Number <Doc> 星星十, 十十 02, 2006 Rev <Rev Code> Sheet 1 of 13 NUC710 EVB USER MANUAL SDD[0..7] nECS0 VDD 1 3 4 7 8 13 14 17 18 10 OE 1D 2D 3D 4D 5D 6D 7D 8D GND VCC 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q E 20 2 5 6 9 12 15 16 19 11 RP19 1 2 3 4 1 1 1 1 1 LED15 LED_R LED_R LED_R LED_R LED_R LED_R LED_R LED_R 8P4R-220 8 7 6 5 RP18 1 2 3 4 2 LED14 2 LED13 2 LED12 2 LED11 2 LED10 U13 GND SDD0 SDD1 SDD2 SDD3 SDD4 SDD5 SDD6 SDD7 GND 1 LED9 2 LED8 2 VDD 1 1 D0-D7 LED DISPLAY 2 SDD[0..7] nECS0 8P4R-220 8 7 6 5 74F373 VDD U14 nECS0 1 2 3 NC VCC A GND Y 5 4 74HC1G04 Title W90P710 AP board Size A Date: - 43 - Document Number <Doc> Wednesday , January 31, 2007 Rev <Rev Code> Sheet 1 of 1 Publication Release Date: Feb 12, 2007 Revision: D NUC710 EVB USER MANUAL EBI EXT. CONNECTOR SDD[0..7] nECS0 SDD[0..7] nECS0 CON1 CON2 VDD A0 A2 A4 A6 A8 A10 A12 A14 A16 A18 A20 nECS2 nECS1 nOE nWBE0 SDD15 SDD13 SDD11 SDD9 SDD7 SDD5 SDD3 SDD1 nIRQ0 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 VDD 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 VDD nRESET A1 A3 A5 A7 A9 A11 A13 A15 A17 A19 A21 nECS0 nWAIT nWBE1 SDD14 SDD12 SDD10 SDD8 SDD6 SDD4 SDD2 SDD0 GND CON4 VDD 1 3 5 7 9 11 13 15 17 19 21 23 C1 33uF/10V 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 VDD nRESET A1 A3 A5 A7 A9 A11 A13 A15 A17 A19 A21 nECS0 nWAIT nWBE1 SDD14 SDD12 SDD10 SDD8 SDD6 SDD4 SDD2 SDD0 GND EBI TEST CON RP1 5 6 7 8 4 3 2 1 CON3 GND SDD30 SDD28 SDD26 SDD24 nECS3 nWBE2 nIRQ2 SDD22 SDD20 SDD18 SDD16 8P4R-22 2 4 6 8 10 12 14 16 18 20 22 24 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 VDD33 nWAIT nIRQ0 nIRQ2 nIRQ3 EBI EXT. CON GND SDD30 SDD28 SDD26 SDD24 nECS3 nWBE2 nIRQ2 SDD22 SDD20 SDD18 SDD16 VDD A0 A2 A4 A6 A8 A10 A12 A14 A16 A18 A20 nECS2 nECS1 nOE nWBE0 SDD15 SDD13 SDD11 SDD9 SDD7 SDD5 SDD3 SDD1 nIRQ0 GND SDD31 SDD29 SDD27 SDD25 nWBE3 nIRQ3 SDD23 SDD21 SDD19 SDD17 VDD 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 GND SDD31 SDD29 SDD27 SDD25 nWBE3 nIRQ3 SDD23 SDD21 SDD19 SDD17 VDD EBI TEST CON C2 EBI EXT. CON 33uF/10V Title <Title> Size A Date: - 44 - Document Number <Doc> 星星十, 十十 02, 2006 Rev <Rev Code> Sheet 2 of 13 NUC710 EVB USER MANUAL RP2 GPIO[10..7] GPIO[10..7] GPIO7 GPIO8 GPIO9 GPIO10 1 2 3 4 TXD1 RXD1 TXD2/CTS1/PS2_CLK RXD2/RTS1/PS2_DAT 8 7 6 5 (UART1/2) CON5 GND 5 9 4 8 3 7 2 6 1 8P4R-22 UCTS1 UTXD URTS1 URXD UART1 + CC1 VDD CC4 CC2 0.1uF U1 0.1uF + CC5 + 0.1uF + URTS1 UCTS1 1 2 3 4 5 6 7 8 C1+ V+ C1C2+ C2VT2_OUT R2_IN VCC GND T1_OUT R1_IN R1_OUT T1_IN T2_IN R2_OUT 16 15 14 13 12 11 10 9 + 0.1uF CC3 DB9_Male 0.1uF Male UTXD/URXD SELECT UTXD1 URXD1 RXD1 TXD1 RTS1 CTS1 JP1 UTXD1 UTXD UTXD2 1 2 3 UTXD SEL MAX202C JP2 UART2 URXD1 URXD URXD2 URXD SEL + CC6 VDD CC8 CC7 0.1uF U2 0.1uF 1 2 3 4 5 6 7 8 + CC10 + 0.1uF + PS/2 C1+ V+ C1C2+ C2VT2_OUT R2_IN VCC GND T1_OUT R1_IN R1_OUT T1_IN T2_IN R2_OUT 16 15 14 13 12 11 10 9 + 0.1uF CC9 UTXD/URXD SELECT JP3 RTS1 RXD2/RTS1 RXD2 0.1uF UTXD2 URXD2 RXD2 TXD2 1 2 3 RTS1/RXD2 SEL JP4 CTS1 TXD2/CTS1 TXD2 1 2 3 CTS1/TXD2 SEL MAX202C LL1 1 2 3 UTXD/URXD SELECT FB JP5 TXD2/CTS1 TXD2/CTS1/PS2_CLK PS2_CLK VDD R1 4.7K R2 4.7K UART/PS2_CLK SEL PS2 CON LL2 PS2_DAT 1 2 3 4 5 6 LL3 CB1 47pF CB2 47pF JP6 RXD2/RTS1 RXD2/RTS1/PS2_DAT PS2_DAT CON6 FB PS2_CLK 1 2 3 FB CB3 LL4 1uF FB 1 2 3 UART/PS2_DAT SEL PS/2 CON Title <Title> Size Document Number Custom<Doc> Date: - 45 - 星星星, 十星十 22, 2005 Rev <Rev Code> Sheet 3 of 13 Publication Release Date: Feb 12, 2007 Revision: D NUC710 EVB USER MANUAL RP3 GPIO[14..11] GPIO[14..11] GPIO11 GPIO12 GPIO13 GPIO14 SW1 1 2 3 4 8 7 6 5 SCL0/SFRM/TIMER0 SDA0/SSPTXD/TIMER1 SCL1/SCLK SDA1/SSPRXD 8 7 6 5 8P4R-22 1 2 3 4 TIMER0 TIMER1 SCL SDA 1 2 3 4 SFRM SSPTXD SCLK SSPRXD 1 2 3 4 NF_CS NF_DI NF_CLK NF_DO SW 1X4 VDD33 I2C SW2 EEPROM ADDRESS:0H R3 R4 8 7 6 5 R5 SFRM SSPTXD SCLK SSPRXD SW 1X4 U3 I2C-EEPROM VDD33 1 2 3 4 CB4 0.1uF A0 A1 A2 GND VCC WP SCL SDA 8 7 6 5 1K 2.2K 2.2K SW3 SCL SDA 8 7 6 5 24LC64 SW 1X4 VDD33 R6 1K nHOLD R7 1K nWP TIMER OUTPUT VDD33 SPI-FLASH U4 NF_CS NF_DO nWP GND VDD33 TIMER0 OUTPUT TIMER1 OUTPUT R8 1 2 3 4 CS DO WP GND VCC HOLD CLK DI 8 7 6 5 VDD33 nHOLD NF_CLK NF_DI W25P10/20/40 R9 220 NexFLASH(SPI) 1 1 220 LED1 LED2 LED_R LED_R SW 1 Q1 2N3904 32 R10 2 3.3k TIMER0 Q2 2N3904 R11 2 OFF SCL(I2C) SCLK(SSP) SDA1/SSPRXD SDA(I2C) SSPRXD(SSP) SCL0/SFRM/TIMER0 T0 OUTPUT SFRM(SSP) SDA0/SSPTXD/TIMER1 T1 OUTPUT SSPTXD(SSP) 3.3k TIMER1 1 32 ON SCL1/SCLK Title <Title> Size A Date: - 46 - Document Number <Doc> 星星星, 十星十 22, 2005 Rev <Rev Code> Sheet 4 of 13 NUC710 EVB USER MANUAL RP4 GPIO[29..20] GPIO[29..20] GPIO20 GPIO21 GPIO22 GPIO23 GPIO24 GPIO25 GPIO26 GPIO27 SD CARD 8P4R-22 8 7 6 5 8 7 6 5 8P4R-22 1 2 3 4 1 2 3 4 RP5 GPIO28 GPIO29 R12 R13 SW6 1 2 3 4 5 6 7 8 SC1_PWR SC1_PRES SC1_RST SC1_CLK SC1_DAT SC0_PWR SC0_PRES SC0_RST SC0_CLK SC0_DAT SW4 1 2 3 4 5 6 7 8 SW5 1 2 SC0_CLK/SD_CLK SC0_DAT/SD_CMD 22 22 SW 1X8 16 15 14 13 12 11 10 9 SW7 1 2 SC1_PWR/nXDACK SC1_PRES/nXDREQ SC1_RST/SD_CD SC1_CLK/SD_PWR SC1_DAT/SD_DAT3 SC0_PWR/SD_DAT2 SC0_PRES/SD_DAT1 SC0_RST/SD_DAT0 SW 1X8 16 15 14 13 12 11 10 9 nXDACK nXDREQ SD_CD SD_PWR SD_DAT3 SD_DAT2 SD_DAT1 SD_DAT0 SW 1X2 4 3 SD_CLK SD_CMD SD_VDD33 SC1_PWR/nXDACK SC1_PRES/nXDREQ SC1_RST/SD_CD SC1_CLK/SD_PWR SC1_DAT/SD_DAT3 SC0_PWR/SD_DAT2 SC0_PRES/SD_DAT1 SC0_RST/SD_DAT0 SD_DAT3 SD_DAT2 SD_DAT1 SD_DAT0 1 2 3 4 RP6 SD_CMD SD_CD SW 1X2 4 3 8 7 6 5 8P4R-4.7K R14 R15 4.7K 4.7K SC0_CLK/SD_CLK SC0_DAT/SD_CMD VDD33 NOP VDD33 SD_WP R81 0 nXDACK R16 4.7K 4.7K SD_VDD33 SD_PWR SI2301SD Q3 LL5 33 CB5 0.1uF CB6 + HOLD 15 R18 R17 CB7 VDD33 FB J2 GND WP DAT1 DAT0 VSS CLK VDD VSS CMD DAT3 DAT2 1uF 0.1uF C3 + 14 HOLD 10uF/16V nXDACK nXDREQ GND CD# J1 1 2 1 2 1X2_HEADER_2.54 11 10 8 7 6 5 4 3 2 1 9 12 13 SD_WP EXT. DMA CON. SD_DAT1 SD_DAT0 SD_CLK SD_CMD SD_DAT3 SD_DAT2 SD_CD Title <Title> SD/MMC SOCKET Size A Date: - 47 - Document Number <Doc> 星星十, 星十 06, 2006 Rev <Rev Code> Sheet 5 of 13 Publication Release Date: Feb 12, 2007 Revision: D NUC710 EVB USER MANUAL SC1_PWR SC1_PRES SC1_RST SC1_CLK SC1_DAT SC0_PWR SC0_PRES SC0_RST SC0_CLK SC0_DAT SC1_PWR SC1_PRES SC1_RST SC1_CLK SC1_DAT SC0_PWR SC0_PRES SC0_RST SC0_CLK SC0_DAT SMART CARD0 Vcc R19 10K CLK R20 VDD M0 0 0 1 1 Vcc 10K DAT R21 10K RST R22 JP8 VDD33 3V/5V GND VDD33 U5 VDD33 GND 3V/5V SC0_PWR Vcc=VIN Vcc=3V Vcc=5V J3 10 9 CB8 0.1uF 10K SHUT DOWN SC0_PRES 3V/5V SEL R23 OPERATING MODE 10K 1 2 3 SC0_CLK SC0_RST SC0_DAT M1 0 1 0 1 1 2 3 4 5 6 7 8 CIN RIN DATA DDRV DVcc SS M1 M0 SLK RST I/O Vcc VIN C1+ C1GND 16 15 14 13 12 11 10 9 4 3 2 1 CLK RST DAT Vcc VDD33 CB10 0.1uF S2 S1 VDD33 C4 C3 C2 C1 C8 C7 C6 C5 8 7 6 5 DAT + C4 CB9 10uF/16V 0.1uF SCSLOT C5 10uF/16V LTC1555L VDD33 SC1_Vcc SMART CARD1 SC1_PWR R24 SI2301SD Q4 SC1_Vcc R25 10K R26 10K R27 10K SC1_CLK SC1_Vcc SC1_RST SC1_CLK CB11 0.1uF 10K SC1_DAT J4 1 2 3 4 C1 C2 C3 C4 C5 C6 C7 C8 5 6 7 8 GND SC1_RST SC1_DAT SC1_PRES SIM Card Slot Title <Title> Size A Date: - 48 - Document Number <Doc> 星星星, 十星十 22, 2005 Rev <Rev Code> Sheet 6 of 13 NUC710 EVB USER MANUAL NC GPIO[4..0] GPIO[4..0] GPIO0 GPIO1 GPIO2 GPIO3 GPIO4 AC-97 R28 1 2 3 4 RP7 SW8 1 2 3 4 5 AC97nRST/I2SSCLK AC97DATI/I2SDATI/PWM0/DTR3 AC97DATO/I2SDATO/PWM1/DSR3 AC97SY NC/I2SWS/PWM2/TXD3 AC97BCLK/I2SBCLK/PWM3/RXD3 22 8 7 6 5 8P4R-22 SW9 8 7 6 5 CB12 XTL-IN 22pF 1 2 3 4 SW 1X5 10 9 8 7 6 AC97_nRST AC97_DATI AC97_DATO AC97_SY NC AC97_BCLK VREFOUT R29 2.2K J5 0 MICROPHONE SW 1X4 R31 22K R32 CB131nF AGND MIC2 VDD33 C6 1K CB25 CB26 22pF SPDIFO SPDIFI/EAPD XTLSEL ID0 GPIO1 GPIO0 AVSS2 HP-OUT-R NC HP-OUT-L AVDD2 MOUT 48 47 46 45 44 43 42 41 40 39 38 37 AC97_SY NC nRST C9 + C7 1nF DVDD1 XTL-IN XTL-OUT DVSS1 SDATA-OUT BIT-CLK DVSS2 SDATA-IN DVDD2 SY NC RESET# BEEP ALC203 + C8 CB16 1nF CB17 10uF/16V HP-OUT-L R34 1nF 100 10uF/16V R35 220K U6 J6 VOUTLO AGND LINE-OUT-R LINE-OUT-L VAUX VREFOUT2 DCVOL NC AFILT2 AFILT1 VREFOUT VREF AVSS1 AVDD1 PHONE AUX-L AUX-R JD2 JD1 CD-L CD-GND CD-R MIC1 MIC2 LINE-IN-L LINE-IN-R 1 2 3 4 5 6 7 8 9 10 11 12 FB VOUTRO AGND 36 35 34 33 32 31 30 29 28 27 26 25 AVDD33 CB19 R36 220K 0.1uF C10 HP-OUT-R 10uF/16V VREFOUT AGND AVDD33 + C11 + C12 10uF/16V AGND CB24 1nF 10uF/16V 13 14 15 16 17 18 19 20 21 22 23 24 1nF 0 CB15 10uF/16V 10uF/16V CB18 XTL-IN XTL-OUT GND AC97_DATO AC97_BCLK GND AC97_DATI LL7 + 0 AVDD33 + 22pF HP-OUT-L AVDD R33 + 24.576MHz Cry stal XTL-OUT GPIO1 GPIO0 AGND HP-OUT-R VDD33 R38 FB MIC1 PWM0/DTR3 PWM1/DSR3 PWM2/TXD3 PWM3/RXD3 X1 CB14 LL6 R30 PWM0/DTR3 PWM1/DSR3 PWM2/TXD3 PWM3/RXD3 CB20 CB21 CB22 CB23 1nF 1nF 1nF 1nF VDD 1nF PHONEJACK STEREO SW R37 100 GPIO1 A B SW 3.3V 1 1 VOL UP 1.65V 0 1 MUTE 0V 0 0 VOL DOWN XTLSEL ID0 R39 VDD33 4.7K CB27 R40 100K 1nF MIC2 R41 CB28 1nF SP1 R42 0 GPIO0 AC97_nRST 0 CB29 1uF GPIO1 MIC1 R43 nRST 0 LL8 AGND CRY-IN NC NC 24.576MHz LOW NC 14.318MHz SP2 FB Vol-Mute GND SP3 R44 Vol-Down Vol-Up 4.7K Title <Title> Size Document Number Custom<Doc> Date: - 49 - 星星星, 十星十 22, 2005 Rev <Rev Code> Sheet 7 of 13 Publication Release Date: Feb 12, 2007 Revision: D NUC710 EVB USER MANUAL SW10 PWM0/DTR3 PWM1/DSR3 PWM2/TXD3 PWM3/RXD3 PW0/DTR3 PWM1/DSR3 PWM2/TXD3 PWM3/RXD3 8 7 6 5 VDD DTR3 DSR3 TXD3 RXD3 1 2 3 4 RP8 1 2 3 4 SW 1X4 8P4R-10K J7 1 2 PWM0 3 PWM1 4 PWM2 PWM3 RP9 1 2 3 4 8 7 6 5 8 7 6 5 PWM0 PWM1 PWM2 PWM3 8P4R-0 PWM CON. PWM Header UART3 (UARTC) CON7 + CC11 GND VDD 0.1uF CC14 0.1uF + CC15 0.1uF + UDTR3 UDSR3 U7 1 2 3 4 5 6 7 8 C1+ V+ C1C2+ C2VT2_OUT R2_IN VCC GND T1_OUT R1_IN R1_OUT T1_IN T2_IN R2_OUT 16 15 14 13 12 11 10 9 CC12 0.1uF + + CC13 UDTR3 0.1uF UTXD3 URXD3 UDSR3 UTXD3 URXD3 RXD3 TXD3 DTR3 DSR3 5 9 4 8 3 7 2 6 1 DB9_Male Male MAX202C Title <Title> Size A Date: - 50 - Document Number <Doc> 星星星, 十星十 22, 2005 Rev <Rev Code> Sheet 8 of 13 NUC710 EVB USER MANUAL GPIO[41..30] GPIO[41..30] SCLK SSPTXD SFRM SSPRXD SCLK SSPTXD SFRM SSPRXD RP10 1 2 3 4 1 2 3 4 RP11 1 2 3 4 RP12 GPIO30 GPIO31 GPIO32 GPIO33 GPIO34 GPIO35 GPIO36 GPIO37 GPIO38 GPIO39 GPIO40 GPIO41 8P4R-22 8 7 6 5 8 7 6 5 8 8P4R-22 7 6 5 8P4R-22 J8 VCLK VDEN VSY NC HSYNC VD0 VD1 VD2 VD3 VD4 VD5 VD6 VD7 VDD33 LCD INTERFACE VOP FB LCDVDD LCDVDD LCDVDD RR1 1 LL9 POCB VDEN SFRM SSPTXD SCLK VSYNC HSYNC VCLK VD7 VD6 VD5 VD4 VD3 VD2 VD1 VD0 VBC VSH COMDC LCDVDD VGH VDC R45 4.7K COMDC VDC VCOM GND VDC C13 CB30 D1 R46 10uF/16V 1uF 0-20K 4.7K RB521S-30 LL10 C14 FB 2 CB31 CB33 4.7K VGL VVCOM VSH VBC POCB VGH COMOUT 1uF R47 L1 + C15 CB35 1uF 4.7uF/10V 1uF R48 + C16 CB36 0.1uF 560K + C17 4.7uF/10V 1uF COMOUT VVCOM GND VCOM VSS TEST POCB BLON CS DI SCK VSY NC HSYNC CLK D7 D6 D5 D4 D3 D2 D1 D0 VBC VSH COMDC VDD VGH VDC1 C2+ C2VGL C1C1+ COMOUT VVCOM VSS COM25T2171T VDD CB34 1uF VGL CB32 3 VCOM VGH 10uF/50V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 D2 6.8uH + C18 2.2uF/10V VOP 4.7uF/10V MBR0520 R49 + C19 4.7uF/10V VDD L2 U8 D3 6.8uH 22 J9 BLH BLL 1 2 MBR0520 R50 6 + - + C20 BACKLIGH 4.7uF/10V 4 2 + C21 22 CB37 VDD EN LX OVP VSS FB 1 1uF 5 NOP 3 R51 0 PC113 4.7uF/10V C22 4.7uF/10V R52 U9 6 + 4 2 VDD EN VSS LX OVP FB 1 Driver IC 12V power 5 9.5 3 PC113 R53 LCD BACKLIGHT 3.3 Title CB38 CB39 1uF 1uF <Title> Size A Date: - 51 - Document Number <Doc> 星星十, 十十 23, 2006 Rev <Rev Code> Sheet 9 of 13 Publication Release Date: Feb 12, 2007 Revision: D NUC710 EVB USER MANUAL TX+ LAN Transformer LAN_AVDD ETHERNET R54 13 12 11 10 TX- TD- NC NC NC NC RX+ RD+ CT 9 9 CT R56 TXRX+ R58 LAN_AVDD 6 R59 0 NOP for DM9161A 7 50R 1% 8 RD- CB44 0.1uF CB43 BOTHHAND TS6121C R60 0.1uF 50R 1% R61 75R 1% RX2KV U11 4 5 0.1uF 2KV CL1 RX_DV RX_ERR DISMDIX nRESET LAN_VDD REFCLK XT1 DGND 37 38 39 40 41 42 43 44 45 46 47 48 LL11FB AGND BGRESG LL12FB 2KV R62 R64 CL2 75R 1% R63 75R 1% 75R 1% 0.1uF 2KV R66 6.8K 1% RXDV/TESTMODE RXER/RXD[4]/RPTR DISMDIX RESET# DVDD XT2 XT1 DGND NC AGND BGRESG BGRES DM9161 Chasis Ground R57 nRESET 0 VDD33 MDC DVDD TXCLK/ISOLATE TXEN TXD[0] TXD[1] TXD[2] TXD[3] TXER/TXD[4] DGND CABLESTS/LINKSTS LINK/ACT LED#/OP2 24 23 22 21 20 19 18 17 16 15 14 13 MDC LAN_VDD TX_CLK TX_EN TXD0 TXD1 CB42 OSC1 1 4 NC VCC GND O 0.1uF 8 REFCLK 5 R65 50MHz 22 TX_ERR DGND CBLLNK ACTLED# LAN_VDD MDIO R67 TX_CLK R68 1.5K 0 CB45 10pF LAN_AVDD LAN_AVDD RX+ RXAGND AGND TX+ TXLAN_AVDD PWRDWN COLLED# SPDLED# XT1 PHY address-->00001H LAN_VDD R69 10K R70 10K R71 10K CBLLNK CB46 22pF TX_ERR PWRDWN OP0:OP1:OP2=111-->Auto Negotiation enable R72 nRESET 1 2 3 4 5 6 7 8 9 10 11 12 Power-on Reset Settings Latched Inputs PHY Address PHY AD0 RXD0 Pulled low normally DISMDIX PHY _RXERR PHY _CRSDV PHY _RXD0 PHY _RXD1 PHY _REFCLK PHY _TXEN PHY _TXD0 PHY _TXD1 PHY _MDIO PHY _MDC 50R 1% 3 CT RX- RJ-45L CON CB40 0.1uF CB41 0.1uF 2 36 35 34 33 32 31 30 29 28 27 26 25 14 8 7 6 5 4 3 2 1 CT COL/RMII CRS/PHYAD[4] RXCLK/SCRAMEN/10BTSER DGND MDINTR# RXEN DVDD RXD[0]/PHYAD[0] RXD[1]/PHYAD[1] RXD[2]/PHYAD[2] RXD[3]/PHYAD[3] MDIO 10 Solder Solder CON8 1 TD+ AVDD AVDD RX+ RXAGND AGND TX+ TXAVDD PWRDWN FDX/COL LED#/OP0 SPEED LED#/OP1 TX+ 15 COL CRSDV RX_CLK DGND U10 LAN_VDD LAN_VDD RXD0 RXD1 RXD2 RXD3 MDIO 50R 1% 16 NC NC RXNC NC RX+ TXTX+ RX_ERR RX_DV RXD0 RXD1 REFCLK TX_EN TXD0 TXD1 MDIO MDC 10K LAN_VDD PHY Address RXD1 PHY AD1 RXD2 PHY AD2 RXD3 PHY AD3 CRSDV PHY AD4 5 6 7 8 4 3 2 1 COLLED# SPDLED# ACTLED# 5 6 7 8 OP0 OP1 OP2 RP13 8P4R-10K 4 3 2 1 VDD33 LAN_AVDD LL13 RP14 8P4R-10K LED3 CB47 LAN_VDD = = = = RMII Enables Scrambing Node Mode Normal Operation COL RX_CLK RX_ERR RX_DV RMII SCRAMBLE RPTR TESTMODE 5 6 7 8 0.01uF LAN_VDD LED_G LAN_AVDD LAN_VDD 1 1 0 0 LAN PORT LED LAN_VDD CB48 0.1uF C23 FB C24 10uF/16V CB49 10uF/16V0.1uF SPDLED# 2 1 100/10 ACTLED# 2 1 LINK/ACT COLLED# 2 CB50 R73 220 R74 220 R75 220 0.1uF LED4 4 3 2 1 LED_G 1 LED5 COL LED_R RP15 8P4R-10K LAN_AVDD LL15 LAN_VDD FB AGND DGND LL16 FB CB51 CB52 CB53 CB54 CB55 CB56 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF CB57 Title W90P710 AP board Size Document Number Custom<Doc> Date: - 52 - Thursday , February 08, 2007 Rev <Rev Code> Sheet 10 of 13 NUC710 EVB USER MANUAL GPIO[51..42] GPIO[51..42] GPIO42 GPIO43 GPIO44 GPIO45 GPIO46 GPIO47 GPIO48 GPIO49 nRESET nRESET RP16 1 2 3 4 RP17 1 2 3 4 8P4R-22 8P4R-22 KPI_COL0/PHY _RXERR KPI_COL1/PHY _CRSDV KPI_COL2/PHY _RXD0 KPI_COL3/PHY _RXD1 KPI_COL4/PHY _REFCLK KPI_COL5/PHY _TXEN KPI_COL6/PHY _TXD0 KPI_COL7/PHY _TXD1 1 2 3 4 5 6 7 8 SW11 SW 1X8 16 15 14 13 12 11 10 9 COL0 COL1 COL2 COL3 COL4 COL5 COL6 COL7 KPI_ROW0/PHY _MDIO KPI_ROW1/PHY _MDC 1 2 SW12 SW 1X2 4 3 ROW0 ROW1 nRESET nRESET GPIO50 GPIO51 PHY _RXERR PHY _CRSDV PHY _RXD0 PHY _RXD1 PHY _REFCLK PHY _TXEN PHY _TXD0 PHY _TXD1 PHY _MDIO PHY _MDC 22 22 1 2 3 4 5 6 7 8 SW13 SW 1X8 16 15 14 13 12 11 10 9 KPI_COL0/PHY _RXERR KPI_COL1/PHY _CRSDV KPI_COL2/PHY _RXD0 KPI_COL3/PHY _RXD1 KPI_COL4/PHY _REFCLK KPI_COL5/PHY _TXEN KPI_COL6/PHY _TXD0 KPI_COL7/PHY _TXD1 1 2 SW14 SW 1X2 4 3 KPI_ROW0/PHY _MDIO KPI_ROW1/PHY _MDC BP2 1 2 COL3 2 R76 R77 COL2 COL1 COL0 BP1 1 8 7 6 5 8 7 6 5 BP3 1 2 KEY BOARD INTERFACE BP4 1 2 ROW0 VDD33 PUSH-KEY BP5 1 PUSH-KEY BP6 2 1 PUSH-KEY BP10 1 PUSH-KEY BP13 1 2 PUSH-KEY 2 2 PUSH-KEY 2 1 PUSH-KEY BP11 1 PUSH-KEY BP14 1 PUSH-KEY BP8 2 2 PUSH-KEY ROW1 BP12 1 PUSH-KEY BP15 1 2 PUSH-KEY COL7 2 1 COL6 1 2 PUSH-KEY COL5 COL4 BP9 PUSH-KEY BP7 2 ROW0 COL0 COL1 COL2 COL3 RP20 5 6 7 8 8P4R-22 4 3 2 1 COL4 COL5 COL6 COL7 RP21 5 6 7 8 8P4R-22 4 3 2 1 PUSH-KEY BP16 1 2 ROW1 PUSH-KEY Title <Title> Size A Date: - 53 - Document Number <Doc> 星星十, 星十 06, 2006 Rev <Rev Code> Sheet 11 of 13 Publication Release Date: Feb 12, 2007 Revision: D NUC710 EVB USER MANUAL GPIO[10..7] GPIO[14..11] GPIO[41..30] GPIO[4..0] GPIO[29..20] GPIO[51..42] nRESET GPIO[10..7] GPIO[14..11] GPIO[41..30] GPIO[4..0] GPIO[29..20] GPIO[51..42] I/O EXT. CONNECTOR nRESET CON9 VDD CON10 VDD C25 33uF/16V VDD GPIO51 GPIO49 GPIO47 GPIO45 GPIO43 GPIO20 GPIO22 GPIO24 GPIO26 GPIO28 nRESET GPIO3 GPIO1 GPIO41 GPIO39 GPIO37 GPIO35 GPIO33 GPIO31 GPIO14 GPIO12 GPIO10 GPIO8 GND 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 VDD GPIO50 GPIO48 GPIO46 GPIO44 GPIO42 GPIO21 GPIO23 GPIO25 GPIO27 GPIO29 GPIO4 GPIO2 GPIO0 GPIO40 GPIO38 GPIO36 GPIO34 GPIO32 GPIO30 GPIO13 GPIO11 GPIO9 GPIO7 GND VDD GPIO51 GPIO49 GPIO47 GPIO45 GPIO43 GPIO20 GPIO22 GPIO24 GPIO26 GPIO28 nRESET GPIO3 GPIO1 GPIO34 GPIO36 GPIO38 GPIO40 GPIO33 GPIO31 GPIO14 GPIO12 GPIO10 GPIO8 GND 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 VDD GPIO50 GPIO48 GPIO46 GPIO44 GPIO42 GPIO21 GPIO23 GPIO25 GPIO27 GPIO29 GPIO4 GPIO2 GPIO0 GPIO35 GPIO37 GPIO39 GPIO41 GPIO32 GPIO30 GPIO13 GPIO11 GPIO9 GPIO7 GND I/O EXT. CON I/O TEST CON Title <Title> Size A Date: - 54 - Document Number <Doc> 星星星, 三十 09, 2006 Rev <Rev Code> Sheet 12 of 13 NUC710 EVB USER MANUAL CON11 +5V SP4 IN 1 2 VDD 3 GND GND POWER SW CB58 CT1 2 3 Power CON 0.1uF 470uF/16V Power LEDs LED_G 2 2 LED_G 1 R78 220 1 LED7 R79 220 VDD33 VDD +3.3V 1A OUT IN GND OUT U12 AMC1117-3.3v LED6 VDD33 4 3 1 2 VDD VDD VDD33 CB60 C27 C26 33uF/16V CB59 0.1uF 33uF/16V 0.1uF GND Title <Title> Size A Date: - 55 - Document Number <Doc> 星星星, 十星十 22, 2005 Rev <Rev Code> Sheet 13 of 13 Publication Release Date: Feb 12, 2007 Revision: D NUC710 EVB USER MANUAL AUO TFT panel board RP1 GPIO11 GPIO12 GPIO13 1 2 3 4 SFRM SSPTXD SCLK 8 7 6 5 8P4R-22 CON1 VDD GPIO51 GPIO49 GPIO47 GPIO45 GPIO43 GPIO20 GPIO22 GPIO24 GPIO26 GPIO28 nRESET GPIO3 GPIO1 GPIO34 GPIO36 GPIO38 GPIO40 GPIO33 GPIO31 GPIO14 GPIO12 GPIO10 GPIO8 GND 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 VDD GPIO50 GPIO48 GPIO46 GPIO44 GPIO42 GPIO21 GPIO23 GPIO25 GPIO27 GPIO29 GPIO4 GPIO2 GPIO0 GPIO35 GPIO37 GPIO39 GPIO41 GPIO32 GPIO30 GPIO13 GPIO11 GPIO9 GPIO7 GND 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 RP2 1 2 3 4 1 2 3 4 RP3 1 2 3 4 RP4 GPIO30 GPIO31 GPIO32 GPIO33 GPIO34 GPIO35 GPIO36 GPIO37 GPIO38 GPIO39 GPIO40 GPIO41 8P4R-22 8 7 6 5 8 7 6 5 8 8P4R-22 7 6 5 8P4R-22 J1 VCLK VDEN VSY NC HSY NC VD0 VD1 VD2 VD3 VD4 VD5 VD6 VD7 V3 V1 + C1 + C2 4.7uF/10V 4.7uF/10V V2 V4 V5 VCOMH VGH V7 + C3 + C4 + C5 4.7uF/10V 4.7uF/10V 4.7uF/10V + C6 4.7uF/10V V6 V8 VCOML VGL V9 + C7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 SFRM SSPTXD SCLK HSY NC VSY NC VCLK VD7 VD6 VD5 VD4 VD3 VD2 VD1 VD0 DRV BLH BLL AVDD VDD33 V1 V2 V3 V4 V5 V6 V7 V8 V9 V10 + C8 4.7uF/10V 4.7uF/10V VGL VGH VCOML VCOMH + C9 4.7uF/10V V10 I/O EXT. CON VDD VCOM CS SDA SCL HSY NC VSY NC DCLK D7 D6 D5 D4 D3 D2 D1 D0 DRV VLED FB AVDD AGND GND VCCI VDC V1 V2 V3 V4 V5 V6 V7 V8 V9 V10 FRP VGL VGH VCOML VCOMH VCOM N.C. AUO 3.0" TFT A030DL01 L1 D1 6.8uH U1 RT9164A-3.3v BLH BLL MBR0520 IN GND OUT R1 + C11 VDD33 AVDD VDD 22 4.7uF/10V C12 4.7uF/10V + 4 2 VDD EN VSS L2 VDD U2 6 EN +3.3V 1A 4 C10 33uF/16V OUT VDD 3 1 2 4.3 LX OVP FB FB VDD33 AVDD 1 5 CB2 C14 3 C13 33uF/16V CB1 0.1uF 33uF/16V C15 0.1uF 10uF/16V PC113 R2 3.3 VDD L3 CB3 CB4 1uF 1uF R3 0 EN R4 0 DRV NOP LCD BACKLIGHT - 56 - GND FB NUC710 EVB USER MANUAL 5. 5.1 BOM LIST Core Module board Bill of Materials Item January 10, 2006 Quantity Reference 18:16:18 Page1 Part ______________________________________________ 1 1 CAP1 100uF/16V 2 32 CB1,CB2,CB3,CB4,CB5,CB6, 0.1uF CB7,CB8,CB9,CB10,CB11, CB12,CB13,CB14,CB15,CB16, CB17,CB18,CB19,CB20,CB21, CB22,CB23,CB24,CB25,CB26, CB27,CB28,CB29,CB30,CB31, CB32 3 5 CC1,CC2,CC3,CC4,CC5 1uF/16V 4 1 CD1 22nF 5 1 CD2 0.01uF 6 4 CD3,CD4,CD5,CD6 7 1 CON1 EBI EXT. CON 8 1 CON2 EBI ADDRESS EXT. CON 20pF 9 1 CON3 I/O EXT. CON 10 1 CON4 JTAG-14 11 1 CON5 Power JACK 12 1 CON6 DSUB-9 13 1 CON7 USB A-TYPE 14 1 CON8 Mimi USB B-TYPE 15 5 C1,C2,C5,C9,C10 16 9 C3,C4,C6,C7,C8,C11,C12, 33uF/16V 22uF/10V C13,C14 17 2 JP2,JP1 15M/80M 18 2 LED2,LED1 19 3 LED3,LED4,LED5 20 9 LL1,LL2,LL3,LL4,LL5,LL6, RED_LED GREEN_LED FB LL7,LL8,LL9 - 57 - Publication Release Date: Feb 12, 2007 Revision: D NUC710 EVB USER NANUAL 21 1 RP1 22 13 RP2,RP3,RP4,RP5,RP6,RP7, 8P4R-10K 8P4R-22 RP8,RP9,RP10,RP11,RP12, RP13,RP14 23 1 RP15 8P4R-4.7K 24 6 R1,R3,R4,R13,R14,R15 10K 25 7 R2,R5,R7,R10,R18,R33,R34 0 26 7 R6,R25,R26,R28,R29,R30, 4.7K R32 27 2 R8,R9 220 28 4 R11,R12,R36,R37 29 2 R17,R16 30 1 R19 31 2 R27,R20 32 4 R21,R22,R23,R24 33 1 R31 1M 34 1 R35 10M 35 2 SP1,SP2 SW PUSHBUTTON 36 3 TP1,TP2,TP3 TEST POINT 37 1 U1 74LS08 38 1 U2 SP705 39 2 U4,U3 W986416EH 40 1 U5 W19B/L320S 41 1 U6 AMC1117-3.3v 42 1 U7 RT9193-1.8v 43 1 U8 SP232ECA 44 1 U9 AMC3526H 45 1 U10 NUC710 46 1 X1 15MHz Crystal 47 1 X2 32.768KHz Crystal 1K 15K 1.5K 22 27 - 58 - NUC710 EVB USER MANUAL 5.2 Application board Bill of Materials Item February 22, 2006 Quantity Reference 10:57:50 Page1 Part ______________________________________________ 1 16 BP1,BP2,BP3,BP4,BP5,BP6, PUSH-KEY BP7,BP8,BP9,BP10,BP11, BP12,BP13,BP14,BP15,BP16 2 2 CB2,CB1 47pF 3 12 CB3,CB6,CB29,CB30,CB31, 1uF CB32,CB33,CB34,CB35,CB37, CB38,CB39 4 42 CC1,CC2,CC3,CC4,CB4,CC5, 0.1uF CB5,CC6,CC7,CB7,CC8,CB8, CC9,CB9,CC10,CB10,CC11, CB11,CC12,CC13,CC14,CC15, CB19,CB36,CB40,CB41,CB42, CB43,CB44,CB48,CB49,CB50, CB51,CB52,CB53,CB54,CB55, CB56,CB57,CB58,CB59,CB60 5 4 CB12,CB14,CB25,CB4622pF 6 13 CB13,CB15,CB16,CB17,CB18, 1nF CB20,CB21,CB22,CB23,CB24, CB26,CB27,CB28 7 1 CB45 10pF 8 1 CB47 0.01uF 9 2 CL2,CL1 0.1uF 2KV 10 2 CON3,CON1 EBI TEST CON 11 2 CON2,CON4 EBI EXT. CON 12 2 CON5,CON7 DB9_Male 13 1 CON6 PS/2 CON 14 1 CON8 RJ-45L CON 15 1 CON9 I/O EXT. CON - 59 - Publication Release Date: Feb 12, 2007 Revision: D NUC710 EVB USER NANUAL 16 1 CON10 I/O TEST CON 17 1 CON11 Power CON 18 1 CT1 19 2 C2,C1 33uF/10V 20 13 C3,C4,C5,C6,C7,C8,C9,C10, 470uF/16V 10uF/16V C11,C12,C13,C23,C24 21 1 C14 10uF/50V 22 7 C15,C16,C18,C19,C20,C21, 4.7uF/10V C22 23 1 C17 2.2uF/10V 24 3 C25,C26,C27 25 1 D1 26 2 D3,D2 MBR0520 27 1 JP1 UTXD SEL 28 1 JP2 URXD SEL 29 1 JP3 RTS1/RXD2 SEL 30 1 JP4 CTS1/TXD2 SEL 31 1 JP5 UART/PS2_CLK SEL 32 1 JP6 UART/PS2_DAT SEL 33 1 JP8 3V/5V SEL 34 1 J1 1X2_HEADER_2.54 35 1 J2 SD/MMC SOCKET 36 1 J3 SCSLOT 37 1 J4 SIM Card Slot 38 1 J5 MICROPHONE 39 1 J6 PHONEJACK STEREO SW 40 1 J7 PWM Header 41 1 J8 COM25T2171T 42 1 J9 BACKLIGH 43 11 LED1,LED2,LED5,LED8,LED9, LED_R 33uF/16V RB521S-30 LED10,LED11,LED12,LED13, LED14,LED15 44 4 LED3,LED4,LED6,LED7LED_G 45 16 LL1,LL2,LL3,LL4,LL5,LL6, FB LL7,LL8,LL9,LL10,LL11, - 60 - NUC710 EVB USER MANUAL LL12,LL13,LL14,LL15,LL16 46 2 L1,L2 6.8uH 47 1 OSC1 50MHz 48 2 Q1,Q2 2N3904 49 2 Q4,Q3 SI2301SD 50 7 RP1,RP8,RP13,RP14,RP15, 8P4R-10K RP20,RP21 51 10 RP2,RP3,RP4,RP5,RP7,RP10, 8P4R-22 RP11,RP12,RP16,RP17 52 1 RP6 8P4R-4.7K 53 1 RP9 8P4R-0 54 2 RP19,RP18 55 1 RR1 56 11 R1,R2,R14,R15,R16,R17, 8P4R-220 0-20K 4.7K R39,R44,R45,R46,R47 57 4 R3,R6,R7,R38 1K 58 3 R4,R5,R29 59 7 R8,R9,R73,R74,R75,R78, 2.2K 220 R79 60 2 R11,R10 61 8 R12,R13,R28,R49,R50,R65, 3.3k 22 R76,R77 62 1 R18 33 63 13 R19,R20,R21,R22,R23,R24, 10K R25,R26,R27,R69,R70,R71, R72 64 12 R30,R32,R33,R41,R42,R43, 0 R51,R55,R57,R58,R68,R81 65 1 R31 22K 66 2 R37,R34 100 67 2 R36,R35 220K 68 1 R40 100K 69 1 R48 560K 70 1 R52 10 - 61 - Publication Release Date: Feb 12, 2007 Revision: D NUC710 EVB USER NANUAL 71 1 R53 3.3 72 4 R54,R56,R59,R60 50R 1% 73 4 R61,R62,R63,R64 75R 1% 74 1 R66 6.8K 75 1 R67 1.5K 76 1 SP1 Vol-Mute 77 1 SP2 Vol-Down 78 1 SP3 Vol-Up 79 1 SP4 POWER SW 80 5 SW1,SW2,SW3,SW9,SW10 81 4 SW4,SW6,SW11,SW13SW 1X8 82 4 SW5,SW7,SW12,SW14SW 1X2 83 1 SW8 84 3 U1,U2,U7 85 1 U3 24LC64 86 1 U4 W25P10/20/40 87 1 U5 LTC1555L 88 1 U6 ALC203 89 2 U8,U9 PC113 90 1 U10 BOTHHAND TS6121C 91 1 U11 DM9161 92 1 U12 AMC1117-3.3v 93 1 U13 74F373 94 1 U14 74LV1G04 95 1 X1 24.576MHz Crystal SW 1X4 SW 1X5 MAX202C - 62 - NUC710 EVB USER MANUAL 5.3 AUO 3” TFT panel module board Bill Of Materials Item May 2,2006 Quantity 17:58:50 Page1 Reference Part ______________________________________________ 1 2 CB1,CB2 0.1uF 2 2 CB3,CB4 1uF 3 1 CON1 I/O EXT. CON 4 11 C1,C2,C3,C4,C5,C6,C7,C8, 5 3 C10,C13,C14 6 1 C15 10uF/16V 7 1 D1 MBR0520 8 1 J1 AUO 3.0" TFT A030DL01 9 1 L1 6.8uH 10 2 L3,L2 FB 11 4 RP1,RP2,RP3,RP4 12 1 R1 22 13 1 R2 3.3 14 2 R3,R4 0 15 1 U1 RT9164A-3.3v 16 1 U2 PC113 4.7uF/10V C9,C11,C12 33uF/16V 8P4R-22 - 63 - Publication Release Date: Feb 12, 2007 Revision: D NUC710 EVB USER NANUAL Important Notice Nuvoton products are not designed, intended, authorized or warranted for use as components in systems or equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for other applications intended to support or sustain life. Further more, Nuvoton products are not intended for applications wherein failure of Nuvoton products could result or lead to a situation wherein personal injury, death or severe property or environmental damage could occur. Nuvoton customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Nuvoton for any damages resulting from such improper use or sales. - 64 -
