Download INSTALL GUIDE FLC-CH(RS)-CH4-EN
Transcript
install guide FLC-CH(RS)-CH4-EN Document number 11992 Revision Date 20130911 fiRmware FLC-CH(RS)-CH4 hardware FLRSCH4 accessories FLPROG (REQUIRED) FLRF1 (OPTIONAL) FLRF2 (OPTIONAL) CARLINK ASCL2 (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. © 2013 BEFORE INSTALLATION 1- Connect module to computer 2- Login to Weblink account 3- Flash firmware to module (module is not preloaded with firmware) 4- Use accessories accordingly (accessories are sold separately) www.flashlogic.com Page 2 of 18 DOC.: #11992 • 20130911 VEHICLE LIST - 1 OF 1 PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TRUNK/HATCH RELEASE DATA/MUX IGNITION CTRL RAP SHUTDOWN CTRL HOOD STATUS (W/OEM SW) DOOR STATUS BRAKE PEDAL STATUS TACHOMETER STATUS SECURE TAKEOVER PARKING LIGHT CTRL* • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 300c AT 08-10 1 • • • • • • • • • • • • • • • • 300c SRT8 AT 08-10 1 • • • • • • • • • • • • • • • • Town & Country AT 08-13 1 • • • • • • • • • • • • • • • • • • Caravan AT 08-10 1 • • • • • • • • • • • • • • • • • • Challenger SXT AT 08-13 1 • • • • • • • • • • • • • • • • Challenger R/T AT 08-13 1 • • • • • • • • • • • • • • • • Challenger SRT8 AT 08-13 1 • • • • • • • • • • • • • • • • Charger SE AT 08-10 1 • • • • • • • • • • • • • • • • Charger R/T AT 08-10 1 • • • • • • • • • • • • • • • • Charger SRT8 AT 08-10 1 • • • • • • • • • • • • • • • • Durango AT 11-13 1 • • • • • • • • • • • • • • • Grand Caravan AT 08-13 1 • • • • • • • • • • • • • • • Journey AT 09-10 1 • • • • • • • • • • • • • • • • Magnum AT 08 1 • • • • • • • • • • • • • • • • RAM 1500 AT 09-12 1 • • • • • • • • • • • • • • • RAM 2500 AT 10-12 1 • • • • • • • • • • • • • • • RAM 3500 AT 10-12 1 • • • • • • • • • • • • • • • Commander AT 08-10 1 • • • • • • • • • • • • • • • • Grand Cherokee AT 08-13 1 • • • • • • • • • • • • • • • • C/V AT 10-13 1 • • • • • • • • • • • • • • • 1500 AT 10-12 1 • • • • • • • • • • • • • • • 2500 AT 10-12 1 • • • • • • • • • • • • • • • 3500 AT 10-12 1 • • • • • • • • • • • • • • • Routan AT 09-12 1 • • • • • • • • • • • • • • • • • • • • • POWER SLIDING DOOR (R) 3X LOCK REMOTE START • 08-10 1 POWER SLIDING DOOR (L) DATA IMMOBILIZER BYPASS 08-10 1 300 Limited AT POWER LIFTGATE YEAR 300 AT INSTALL TYPE MODEL VW RAM JEEP DODGE CHRYSLER MAKE FEATURES • • • * May require additional parts. Automotive Data Solutions Inc. © 2013 FLC-CH(RS)-CH4-EN www.flashlogic.com Page 3 of 18 DOC.: #11992 • 20130911 CHRYSLER 300C 300 SRT8 Town & Country Town & Country Caravan Challenger R/T Challenger SXT Challenger SRT8 DODGE Charger SE Charger R/T Charger SRT8 Durango Grand Caravan Grand Caravan Journey Magnum 08-10 08-10 08-10 11-13 08-10 08-13 08-13 08-13 08-10 08-10 08-10 11-13 08-10 11-13 09-10 08 Automotive Data Solutions Inc. © 2013 POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR 08-10 CONNECTOR TYPE 300 Limited CONNECTOR COLOR 08-10 Parking Light D2242 Black 10 pin 1 White/Brown (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 1 White/Brown (MUX) Switch ~ CONNECTOR NAME YEAR 300 WIRE DESCRIPTION MODEL MAKE TYPE 1 - WIRE CHART - 1 OF 2 Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 1 White/Brown (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 1 White/Brown (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 1 White/Brown (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light D2242 Black 6 pin 3 White/Green (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 1 White/Brown (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 1 White/Brown (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 1 White/Brown (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 1 White/Brown (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 1 White/Brown (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 1 White/Brown (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 1 White/Brown (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light D2242 Black 6 pin 1 White/Green (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 1 White/Brown (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light D2242 Black 6 pin 3 White/Green (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light ~ ~ ~ ~ White/Violet (+) Driver kick panel ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 1 White/Brown (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ FLC-CH(RS)-CH4-EN www.flashlogic.com Page 4 of 18 DOC.: #11992 • 20130911 RAM C/V 1500 2500 VW 3500 Routan 10 11-13 10-12 10-12 10-12 09-12 Automotive Data Solutions Inc. © 2013 Parking Light D2242 Black 10 pin 01 White (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 01 White (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 01 White (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light ~ ~ ~ ~ Pin #1 of relay #7 (-) Power module in engine compartment ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light ~ ~ ~ ~ Pin #1 of relay #7 (-) Power module in engine compartment ~ Driver Door Pin ~ ~ ~ ~ Purple (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 01 White/Brown (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ (-) Driver kick panel ~ Parking Light D2242 Black 6 pin 01 White/Green (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 01 White (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 01 White (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 01 White (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ (-) Driver kick panel ~ Parking Light D2242 Black 10 pin 01 White/Brown (MUX) Switch ~ Driver Door Pin ~ ~ ~ ~ (-) Driver kick panel ~ WIRE COLOR COMPONENT LOCATOR C/V 08-13 MODULE LOCATION Grand cherokee 08-10 POLARITY Commander 10-12 POSITION JEEP Ram 3500 10-12 CONNECTOR TYPE Ram 2500 CONNECTOR COLOR YEAR 09-12 CONNECTOR NAME MODEL Ram 1500 WIRE DESCRIPTION DODGE MAKE TYPE 1 - WIRE CHART - 2 OF 2 Purple Purple Purple Purple Purple Purple Purple Purple FLC-CH(RS)-CH4-EN www.flashlogic.com Page 5 of 18 DOC.: #11992 • 20130911 TYPE 1 - WIRING DIAGRAM - 1 OF 2 MODULE VEHICLE IGNITION SWITCH A1 G F E A B VS1 IGNITION CONNECTOR D C A2 VS2 IGNITION HARNESS A 2 4 6 1 3 5 2 4 6 8 10 12 14 16 18 20 1 3 5 7 9 11 13 15 17 19 MS2 B A1 MS1 VEHICLE WHITE/GREEN (NC) WHITE/RED (NC) WHITE/BROWN - PARKING LIGHT (MUX) OUTPUT PARKING LIGHT CONNECTION CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT (MUX) PARKING LIGHT (MUX) OR C 2 1 4 3 6 5 8 7 10 9 12 11 CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT (-) 01 BROWN/BLACK - PARKING LIGHT (-) OUTPUT 02 GRAY - RAP SHUTDOWN (-) OUTPUT 10 AMPS PARKING LIGHT (-) 12V (+) OR 11 GRAY/GREEN - HORN (-) OUTPUT CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT (+) 85 87 86 87A 30 PARKING LIGHT (+) OPTIONAL Automotive Data Solutions Inc. © 2013 FLC-CH(RS)-CH4-EN DRIVER DOOR PIN (-) HORN (-) www.flashlogic.com Page 6 of 18 DOC.: #11992 • 20130911 TYPE 1 - WIRING DIAGRAM - 2 OF 2 MODULE G F E A B D C D VEHICLE 2 4 6 8 10 G F G 1 3 5 7 9 03 GRAY/BLACK (NC) 04 GRAY/WHITE - HOOD STATUS (-) INPUT WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH (-) 1 2 3 4 TELEMATIC 1 2 3 4 RF KIT Automotive Data Solutions Inc. © 2013 FLC-CH(RS)-CH4-EN www.flashlogic.com MODULE PROGRAMMING PROCEDURE - STD KEY - 1 OF 1 01 Close driver door. 07 Turn key to OFF position. ACC ON START OFF 02 Re-open driver door to wake up data bus. 08 Remove key. ACC OFF 03 ON START Insert key into ignition. 09 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. Turn key to ON position. 10 Wait, LED will turn solid GREEN for 2 seconds. 05 LED will turn solid RED. 11 Module Programming Procedure completed. 06 Within 5 seconds, LED will flash GREEN rapidly. ACC ON START OFF 04 ACC OFF ON Page 7 of 18 DOC.: #11992 • 20130911 START Automotive Data Solutions Inc. © 2013 FLC-CH(RS)-CH4-EN www.flashlogic.com MODULE PROGRAMMING PROCEDURE - PTS - 1 OF 1 01 Close driver door. 09 Press UNLOCK on the OEM remote. 02 Re-open driver door to wake up data bus. 10 Wait, LED will turn solid GREEN for 2 seconds. DO NOT PRESS BRAKE PEDAL. Push start button twice [2x] to ON position. 11 Module Programming Procedure completed. 03 STOP ACC ON START Page 8 of 18 DOC.: #11992 • 20130911 ENGINE START STOP 05 LED will turn solid RED. 06 Within 5 seconds, LED will flash GREEN rapidly. 07 STOP ACC ON START DO NOT PRESS BRAKE PEDAL. Push start button once [1x] to OFF position. ENGINE START STOP Automotive Data Solutions Inc. © 2013 FLC-CH(RS)-CH4-EN www.flashlogic.com VALET MODE PROGRAMMING PROCEDURE - 1 OF 1 >> 01 ACC 06 Insert key into ignition. 07 Valet Mode Programming Procedure completed. Time restriction. Complete next step within 7 seconds. >> To exit valet mode: repeat steps 1 to 6. Remove key. ACC OFF ON START ON START OFF 02 03 NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. Page 9 of 18 DOC.: #11992 • 20130911 Turn key to OFF position then to ON position five times [5x] rapidly. 5x ACC ON START OFF 04 Wait, LED 1 will turn solid RED for 2 seconds. 05 Turn key to OFF position. ACC OFF ON START Automotive Data Solutions Inc. © 2013 FLC-CH(RS)-CH4-EN www.flashlogic.com aFteRmaRKet Remote PRogRamming - 1 OF 1 Page 10 of 18 DOC.: #11992 • 20130911 aFteRmaRKet Remote PRogRamming: notes I All aftermarket remotes must be programmed to the RF-Kit. Refer to the RF-Kit user guide for aftermarket remote features and programming procedures. Automotive Data Solutions Inc. © 2013 FLC-CH(RS)-CH4-EN www.flashlogic.com Page 11 of 18 DOC.: #11992 • 20130911 MODULE NAVIGATION PROCEDURE - 1 OF 1 >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP 13. 04 >> Module must be programmed to the vehicle. 05 >> Use the Module Navigation Chart on the next page. 06 Set ignition to OFF position. 07 TO ACCESS THE MENUS: Press and hold programming button until LED 1 turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED 1 will flash GREEN an equal amount of times continuously. 09 01 ACC ON START OFF 02 03 [X] Automotive Data Solutions Inc. © 2013 TO ACCESS THE OPTIONS: Press and hold programming button until LED 1 turns solid RED. 10 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED 1 will flash RED an equal amount of times continuously. 11 TO ACCESS THE SETTINGS: Press and hold programming button until LED 1 turns solid GREEN. 12 Configure every other setting and proceed to step 13. [Z] LED 1 will flash GREEN as many times as the current (or default) setting number, continuously. 13 MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED 1 will flash RED rapidly. Release programming button. LED 1 will turn OFF. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED 1 will flash GREEN an equal amount of times continuously. 14 Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] FLC-CH(RS)-CH4-EN To save and return to the OPTIONS: Press and hold programming button until LED 1 turns solid RED. [Y] LED 1 will flash RED as many times as the current option number continuously. www.flashlogic.com Page 12 of 18 DOC.: #11992 • 20130911 [Y] oPtions [X] menus moDuLe navigation chaRt: notes I Default settings are listed in bold. 01 II Make sure the option is covered on the vehicle before attempting to change the setting. 02 03 04 DISARM/UNLOCK BEFORE START RELOCK AFTER START RELOCK AFTER SHUTDOWN FORCE UNLOCK ALL ON FIRST PRESS 05 TAKEOVER 06 N/A 07 01 [Z] settings moDuLe navigation chaRt - 1 OF 2 FACTORY KEYLESS RS SEQUENCE CONFIGURATION 08 09 MODULE RUN TIME WAIT TO START DELAY 01 oFF 02 ON 01 oFF 02 ON 01 oFF 02 ON 01 oFF 02 ON 01 enabLe 02 DISABLE* 01 N/A 01 DISABLE 02 N/A 03 LOCK + UNLOCK + LOCK 04 LocK + LocK + LocK 01 03 MIN 02 05 MIN 03 10 MIN 04 15 MIN 05 25 MIN 06 30 MIN 07 35 MIN 08 15 min 01 02 sec 02 05 SEC 03 08 SEC 04 10 SEC 05 15 SEC 06 20 SEC 07 25 SEC 08 30 SEC 10 N/A 01 N/A 11 N/A 01 N/A 12 N/A 01 N/A 13 N/A 01 N/A *Vehicle will shutdown when a door is opened. Automotive Data Solutions Inc. © 2013 FLC-CH(RS)-CH4-EN www.flashlogic.com Page 13 of 18 DOC.: #11992 • 20130911 [Y] oPtions [X] menus moDuLe navigation chaRt: notes 14 01 [Z] settings moDuLe navigation chaRt - 2 OF 2 HORN EVENT TRIGGER CONFIGURATION 15 02-07 Technical Support only 01 HORN CHIRPS WIDTH N/A 01 DoubLe LocK 02 LOCK + UNLOCK 03 LOCK + UNLOCK + START 04 DOUBLE LOCK + START 01 30 msec 02 15 mSec 03 60 mSec 01 N/A *Vehicle will shutdown when a door is opened. Automotive Data Solutions Inc. © 2013 FLC-CH(RS)-CH4-EN www.flashlogic.com [X] numbeR oF PaRKing Light FLashes Diagnostic Remote staRteR eRRoR coDes - 1 OF 1 I WARNING: The following applies only when the parking lights are connected and supported by the system. 03 Foot brake is ON. 04 Hood is open. II After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 05 Engine tach signal is lost. 06 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error. 09 RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence. 10 N/A 11 N/A 12 N/A 13 N/A 14 N/A 15 N/A 16 CAN communication failure during RS sequence. Remote staRteR eRRoR coDes: notes Automotive Data Solutions Inc. © 2013 FLC-CH(RS)-CH4-EN Page 14 of 18 DOC.: #11992 • 20130911 www.flashlogic.com I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Automotive Data Solutions Inc. © 2013 Diagnostic test moDuLe LeD 1 status moDuLe Diagnostics - 1 OF 1 Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then OFF Module correctly programmed. OFF No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then OFF Reset in progress. OFF Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then OFF Reset in progress. OFF Module at rest and ready for a remote start sequence. FLC-CH(RS)-CH4-EN Page 15 of 18 DOC.: #11992 • 20130911 www.flashlogic.com MODULE RESET PROCEDURE - 1 OF 1 01 Disconnect all connectors from module except the BLACK 20-PIN connector. 07 Reconnect all connectors. 02 Disconnect the BLACK 20-PIN connector. 08 Repeat programming procedure. 03 PRESS AND HOLD programming button while connecting the BLACK 20-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 04 Wait, LED 1 will flash RED. RELEASE programming button. 05 LED 1 will turn RED for 2 seconds. 06 Module RESET completed. Automotive Data Solutions Inc. © 2013 FLC-CH(RS)-CH4-EN Page 16 of 18 DOC.: #11992 • 20130911 www.flashlogic.com TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC Failure to follow procedure will result in vehicle engine shutdown. ON START OFF 03 >> Page 17 of 18 DOC.: #11992 • 20130911 Turn key to ON position. ACC OFF ON START 04 Press and release BRAKE pedal. 05 Take over procedure completed. Automotive Data Solutions Inc. © 2013 FLC-CH(RS)-CH4-EN www.flashlogic.com TAKEOVER PROCEDURE - PTS - 1 OF 1 >> All vehicle doors must be closed and locked prior to remote start sequence. 01 Press unlock on OEM or aftermarket remote or request switch. 02 STOP ACC ON START Page 18 of 18 DOC.: #11992 • 20130911 DO NOT PRESS BRAKE PEDAL. Push start button twice [2x] to ON position. Wait 2 seconds for key validation. ENGINE START STOP 03 Press and release BRAKE pedal. 04 Take over procedure completed. >> Failure to follow procedure will result in vehicle engine shutdown. Automotive Data Solutions Inc. © 2013 FLC-CH(RS)-CH4-EN www.flashlogic.com