Download #13855 - AE PT FF manual

#13855 - AE PT FF manual
9/4/03
11:40 am
Page 1
http://www.ashdownmusic.com
O perating
I nstructio ns
After Eight
Perfect Ten
Five Fifteen
Page 3
Operating Instructions
Panel Diagrams
FRONT PANEL
After Eight
Front Panel
Ashdown
EQ
The EQ has Bass, Mid and Treble tone controls as well as a Deep push switch.
The Deep switch increases the low bass boost as well as reducing the degree of Mid frequencies in the
signal to provide an alternative tonal character.
INPUT
GAIN
BASS
MIDDLE
TREBLE
OUTPUT
LEVEL
HEAD
PHONES
DEEP
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
MIN
POWER
MAX
ON
15 w
After Eight
Back Panel
Model No:-
Serial No:-
After Eight
OFF
TO REDUCE THE RISK OF
FIRE OR ELECTRICALSHOCK DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE.
CAUTION
THIS APPARATUS MUST BE EARTHED.
FOR CONTINUED PROTECTION
AGAINST RISK OF FIRE REPLACE ONLY
WITH SAME TYPE AND RATING OF FUSE.
UTILISER UN FUSIBLE DE RECHANGE DE
MEME TYPE ET CALIBRE.
POWER
50/60Hz V A.C.
Perfect Ten
Front Panel
INPUT
GAIN
BASS
MIDDLE
TREBLE
OUTPUT
LEVEL
DEEP
MAX
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAINS INPUT 30V.A 115V @ 260mA
Perfect
Design
INSTRUMENT
INPUT
FUSE
RATING
115 V T500 mA
230 V T315 mA
ATTENTION
Ashdown
HEAD
PHONES
EXT SPKR
8 OHMS
Ten
30 W
POWER
MAX
IN/OUT
ON
Perfect Ten
Back Panel
THIS APPARATUS MUST BE EARTHED.
FOR CONTINUED PROTECTION
AGAINST RISK OF FIRE REPLACE ONLY
WITH SAME TYPE AND RATING OF FUSE.
UTILISER UN FUSIBLE DE RECHANGE DE
MEME TYPE ET CALIBRE.
Model No:-
Perfect Ten
CAUTION
OFF
POWER
o
TO REDUCE THE RISK OF
FIRE OR ELECTRICALSHOCK DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE.
REAR PANEL
50/60Hz V A.C.
FUSE
RATING
115 V T1A
230 V T500 mA
Serial No:Designed in England by Ashdown Engineering manufactured in China.
Five Fifteen
Front Panel
Ashdown
MAINS INPUT 60V A 115V @ 520mA
Fifteen
Five
Design
INSTRUMENT
INPUT
INPUT
GAIN
BASS
MIDDLE
TREBLE
OUTPUT
LEVEL
DEEP
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
MIN
HEAD
PHONES
EXT SPKR
8 OHMS
65 w
POWER
MAX
IN/OUT
ON
SPECIFICATIONS
FiveFifteen
15 Watts RMS
1 MΩ
100mV to 10V
30 Watts RMS
1 MΩ
100mV to 10V
65 Watts RMS
1 MΩ
100mV to 10V
Five Fifteen
Back Panel
TO REDUCE THE RISK OF
FIRE OR ELECTRICALSHOCK DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE.
CAUTION
Model No:-
Five Fifteen
THIS APPARATUS MUST BE EARTHED.
FOR CONTINUED PROTECTION
AGAINST RISK OF FIRE REPLACE ONLY
WITH SAME TYPE AND RATING OF FUSE.
UTILISER UN FUSIBLE DE RECHANGE DE
MEME TYPE ET CALIBRE.
Serial No:-
ATTENTION
OFF
POWER
o
PerfectTen
50/60Hz V A.C.
100V
ON
I
Output Power
Input Impedance
Input Signal Range
AfterEight
100V
ON
ATTENTION
FUSED MAINS INLET SOCKET
This is for connection of the unit to your countries mains power supply. Please ensure that the type and
rating of mains fuse marked on the rear panel is used when this is replaced.
POWER SWITCH
The power to the unit is turned on with the rear panel power switch. A power LED on the front panel will
light to indicate that the amplifier is switched on.
100V
ON
Designed in England by Ashdown Engineering manufactured in China.
MIN
EXTERNAL SPEAKER
An External Speaker socket is provided to allow you to use an external speaker cabinet if required.This
cuts out the main speaker when a jack plug is inserted.The external speaker must be a minimum
impedance of 8 Ohms.
Eight
EXT SPKR
8 OHMS
IN/OUT
OUTPUT LEVEL
Use the Output Level control to adjust the playing volume of the amplifier.
HEADPHONES
A Headphone jack socket is provided to allow stereo headphones to be plugged into the amplifier for
silent practice.This cuts out the main speaker when a jack plug is inserted.
After
Design
INSTRUMENT
INPUT
INPUT
A single input jack socket is provided for your instrument.This is a high impedance input designed to
perfectly match the impedance of the pick-ups on a passive bass. It also has sufficient headroom available to
allow active basses to be used. Use the Input Gain control to adjust for the sensitivity of your instrument.
I
11:40 am
o
9/4/03
I
#13855 - AE PT FF manual
FUSE
RATING
115 V T1A
230 V T500 mA
Designed in England by Ashdown Engineering manufactured in China.
MAINS INPUT 100V A 115V @ 900mA