Download 20AF43
Transcript
FILE NO. 050-200309 REVISION 1 SERVICE MANUAL COLOR TELEVISION 20AF43 DOCUMENT CREATED IN JAPAN, Mar., 2005 SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, they are indicated with the labels or seals on the cabinet, chassis and parts. Make sure to keep the indications and notices in the operation manual. Safety is secured against an X-ray by considering about the cathode-ray tube and the high voltage peripheral circuit, etc. Therefore, when repairing the high voltage peripheral circuit, use the designated parts and make sure not modify the circuit. Repairing except indicates causes rising of high voltage, and it emits an X-ray from the cathoderay tube. 2. AVOID AN ELECTRIC SHOCK There is a high voltage part inside. Avoid an electric shock while the electric current is flowing. 3. USE THE DESIGNATED PARTS The parts in this equipment have the specific characters of incombustibility and withstand voltage for safety. Therefore, the part which is replaced should be used the part which has the same character. Especially as to the important parts for safety which is indicated in the circuit diagram or the table of parts as a mark, the designated parts must be used. 7. PERFORM A SAFETY CHECK AFTER SERVICING Confirm that the screws, parts and wiring which were removed in order to service are put in the original positions, or whether there are the portions which are deteriorated around the serviced places serviced or not. Check the insulation between the antenna terminal or external metal and the AC cord plug blades. And be sure the safety of that. 4. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING (INSULATION CHECK PROCEDURE) 1. Unplug the plug from the AC outlet. 2. Remove the antenna terminal on TV and turn on the TV. 3. Insulation resistance between the cord plug terminals and the eternal exposure metal [Note 2] should be more than 1M ohm by using the 500V insulation resistance meter [Note 1]. 4. If the insulation resistance is less than 1M ohm, the inspection repair should be required. There are parts which use the insulation material such as a tube or tape for safety, or which are assembled in the condition that these do not contact with the printed board. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. Therefore, put these parts in the original positions. 5. TAKE CARE TO DEAL WITH THE CATHODE-RAY TUBE [Note 1] If you have not the 500V insulation resistance meter, use a Tester. In the condition that an explosion-proof cathoderay tube is set in this equipment, safety is secured against implosion. However, when removing it or serving from backward, it is dangerous to give a shock. Take enough care to deal with it. [Note 2] External exposure metal: Antenna terminal Earphone jack HOW TO ORDER PARTS Please include the following informations when you order parts. (Particularly the VERSION LETTER.) 1. MODEL NUMBER and VERSION LETTER The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be found at the end of the SERIAL NUMBER. 2. PART NO. and DESCRIPTION You can find it in your SERVICE MANUAL. IMPORTANT Inferior silicon grease can damage IC's and transistors. When replacing an IC's or transistors, use only specified silicon grease (YG6260M). Remove all old silicon before applying new silicon. A1-1 TABLE OF CONTENTS SERVICING NOTICES ON CHECKING ..................................................................................... HOW TO ORDER PARTS .......................................................................................................... IMPORTANT ............................................................................................................................... TABLE OF CONTENTS .............................................................................................................. GENERAL SPECIFICATIONS ................................................................................................... DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP ............................................................................................... 2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ................................................ SERVICE MODE LIST ................................................................................................................ CONFIRMATION OF HOURS USED ......................................................................................... WHEN REPLACING EEPROM (MEMORY) IC .......................................................................... ELECTRICAL ADJUSTMENTS .................................................................................................. BLOCK DIAGRAMS ................................................................................................................... PRINTED CIRCUIT BOARDS MAIN ........................................................................................................................................ CRT/VMCOIL ........................................................................................................................... SCHEMATIC DIAGRAMS MICON ..................................................................................................................................... CHROMA ................................................................................................................................. DEFLECTION .......................................................................................................................... POWER ................................................................................................................................... SOUND .................................................................................................................................... TUNER/STEREO ..................................................................................................................... AV ............................................................................................................................................ COMB/FILTER ......................................................................................................................... CRT/SVM ................................................................................................................................. WAVEFORMS ............................................................................................................................. MECHANICAL EXPLODED VIEWS ........................................................................................... MECHANICAL REPLACEMENT PARTS LIST ......................................................................... ELECTRICAL REPLACEMENT PARTS LIST ........................................................................... A2-1 A1-1 A1-1 A1-1 A2-1 A3-1~A3-5 B1-1 B2-1, B2-2 C1-1 C1-1 C1-1 D-1~D-5 E-1, E-2 F-1~F-4 F-5, F-6 G-1, G-2 G-3, G-4 G-5, G-6 G-7, G-8 G-9, G-10 G-11, G-12 G-13, G-14 G-15, G-16 G-17, G-18 H-1, H-2 I1-1 J1-1 J2-1~J2-4 GENERAL SPECIFICATIONS G-1 TV System CRT CRT Size / Visual Size CRT Type Deflection Magnetic Field BV/BH 20 inch / 508mmV Flat 90 degree +0.45G/0.18G NTSC 2 Speaker Front Side 2 x 4.7 Inch 8 ohm 2.5+2.5 W 2.0+2.0 W No US System M 1Tuner USA(W/ CATV) F-Synth VHF/UHF 75 ohm 2 - 69, 4A, A-5 - A-1, A - I, J - W, W+1 - W+84 45.75MHz 41.25MHz 4.50MHz No Yes Yes 120V AC 60Hz Color System Speaker Sound Output G-2 Tuning System NTSC3.58+4.43 /PAL60Hz Broadcasting System Tuner and Receive CH Intermediate Frequency G-3 Power Preset CH Stereo/Dual TV Sound Tuner Sound Muting Power Source Position Size Impedance MAX 10%(Typical) System Destination Tuning System Input Impedance CH Coverage Picture(FP) Sound(FS) FP-FS AC DC Power Consumption Protector G-4 Regulation G-5 Temperature G-6 Operating Humidity at AC Stand by (at AC) Per Year Power Fuse Safety Radiation X-Radiation Operation Storage A3-1 105 W at AC 120 V 60 Hz 3 W at AC 120 V 60 Hz -kWh/Year Yes UL/CSA FCC/IC DHHS/HWC +5oC ~ +40oC -20oC ~ +60oC Less than 80% RH GENERAL SPECIFICATIONS G-7 On Screen Display Menu Menu Type Picture Contrast Brightness Color Tint Sharpness Sound Bass Treble Balance BBE On/Off Stable Sound On/Off Surround On/Off Set Up TV/CATV Auto CH Memory Add/ Delete Option Language CH Label Favorite CH V-Chip Lock On/Off Timer Color Stream DVD/DTV Control Level Volume Brightness Contrast Color Tint (NTSC Only) Sharpness Tuning Bass Treble Balance Back Light Stereo,Audio Output,SAP Video Color Stream Channel(TV/Cable) CH Label Game Timer Sleep Timer Sound Mute V-chip Rating 16: 9 G-8 OSD Language G-9 Clock and Timer Sleep Timer Max Time Step Program(On Timer / Off Timer / Clock) On/Off Timer Wake Up Timer Timer Back-up (at Power Off Mode) A3-2 more than Yes Icon Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes English French Spanish 120 Min 10 Min Yes -- No Min Sec GENERAL SPECIFICATIONS G-10 Remote Control Unit Glow in Dark Remocon Format Custom Code Power Source Total Keys Keys Multi Brand Keys Voltage(D.C) UM size x pcs Power 1 2 3 4 5 6 7 8 9 0 100 CH Up/+ CH Down/Volume Up/+ Volume Down/C.C.(TV/Caption/Text) CH1/CH2 TV/Video(Input Select) CH RTN(Quick View) SLEEP RECALL(Call) Reset Menu/Enter Mute Exit MTS(Audio Select) Fav. Up Fav. Down 16: 9 CH Up(VCR) CH Down(VCR) Pause/Still TV/VCR(VCR) FF Rew Rec Play Stop TV VCR Cable DVD CODE DVD MENU < DVD MENU > DVD CLEAR TOP MENU DVD MENU A3-3 RC-GF Yes Toshiba TV:40-BFh 3V UM-4 x 2 pcs 49 Keys Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes GENERAL SPECIFICATIONS G-11 Features Auto Degauss Auto Shut Off Canal+ CATV Anti-theft Rental Memory(Last CH) Memory(Last Volume) V-Chip Yes Yes No Yes No No Type BBE Auto Search CH Allocation SAP Just Clock Function CH Label VM Circuit Full OSD Premiere Comb Filter G-12 Accessories Auto CH Memory Hotel Lock Closed Caption Stable Sound FBT Leak Test Protect CH Lock Video Lock Game Timer (Max Time:120 Min) Energy Star Favorite CH Surround 16:9 Mode Owner's Manual Language W/ Warranty Remote Control Unit Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Station List Important Safety Instruction Dew/AHC Caution Sheet AC Plug Adapter Quick Set-up Sheet Battery UM size x pcs OEM Brand AC Cord AV Cord (2Pin-1Pin) Registration Card (NDL Card) PTB Sheet ESP Card 300 ohm to 75 ohm Antenna Adapter A3-4 Yes Yes Yes USA,Toshiba Type Yes No No Yes No Yes Yes No No Yes 3 Lines Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes English / French Yes Yes No No No No No No No No No No No No No Yes UM-4 x 2 No No No Yes No Yes No GENERAL SPECIFICATIONS G-13 Interface Switch Front Rear Indicator Terminals Front Rear G-14 G-15 Set Size Weight G-16 Carton Power System Select Main Power SW Sub Power Channel Up Channel Down Volume Up Volume Down AC/DC TV/CATV Selector Degauss Main Power SW Power Stand-by On Timer Video Input = VIDEO3 Audio Input = VIDEO3 Other Terminal Video Input(Rear1) = VIDEO1 Video Input(Rear2) = VIDEO2 Audio Input(Rear1) = VIDEO1 Audio Input(Rear2) = VIDEO2 Video Output Audio Output Euro Scart Color Stream S Input Diversity Ext Speaker DC Jack 12V(Center +) VHF/UHF Antenna Input AC Outlet Approx. W x D x H (mm) Net (Approx.) Gross (Approx.) Master Carton Content Material Dimensions W x D x H(mm) Description of Origin Gift Box Material Dimensions W x D x H(mm) Design Description of Origin Drop Test G-17 Cabinet Material Height (cm) Container Stuffing Cabinet Cabinet Front Cabinet Rear PCB Non-Halogen Demand Eyelet Demand A3-5 Yes No No No Yes Yes Yes Yes No No No No Yes(RED) No No RCA RCA x 2 Head Phone RCA RCA RCA x 2 RCA x 2 RCA RCA x 2 No RCA x 3 Yes No No No F Type No 590 x 484 x 446.5 23 kg ( 50.6 lbs) 26.5 kg ( 58.3 lbs) No ---Sets -/--- x -- x -No Yes Double/Brown 695 x 575 x 549 As per Buyer's Yes Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces 46 272 Sets/40' container PS 94V0 DECABROM PS 94V0 DECABROM No Yes DISASSEMBLY INSTRUCTIONS 3. After one side is removed, pull in the opposite direction to remove the other. 1. REMOVAL OF ANODE CAP Read the following NOTED items before starting work. NOTE * After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. * Do not use pliers to loosen or tighten the Anode Cap terminal, this may cause the spring to be damaged. Take care not to damage the Rubber Cap. INSTALLATION 1. Clean the spot where the cap was located with a small amount of alcohol. (Refer to Fig. 1-3.) REMOVAL Location of Anode Cap 1. Follow the steps as follows to discharge the Anode Cap. (Refer to Fig. 1-1.) Connect one end of an Alligator Clip to the metal part of a flat-blade screwdriver and the other end to ground. While holding the plastic part of the insulated Screwdriver, touch the support of the Anode with the tip of the Screwdriver. A cracking noise will be heard as the voltage is discharged. Fig. 1-3 GND on the CRT NOTE Confirm that there is no dirt, dust, etc. at the spot where the cap was located. 2. Arrange the wire of the Anode Cap and make sure the wire is not twisted. 3. Turn over the Rubber Cap. (Refer to Fig. 1-4.) Screwdriver Support CRT Alligator Clip GND on the CRT Fig. 1-4 Fig. 1-1 4. Insert one end of the Anode Support into the anode button, then the other as shown in Fig. 1-5. 2. Flip up the sides of the Rubber Cap in the direction of the arrow and remove one side of the support. (Refer to Fig. 1-2.) Rubber Cap CRT Support CRT Support 5. Confirm that the Support is securely connected. 6. Put on the Rubber Cap without moving any parts. Fig. 1-2 B1-1 Fig. 1-5 DISASSEMBLY INSTRUCTIONS 3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) 2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC REMOVAL NOTE 1. Put the Masking Tape (cotton tape) around the Flat Package IC to protect other parts from any damage. (Refer to Fig. 2-1.) Some ICs on the PCB are affixed with glue, so be careful not to break or damage the foil of each IC leads or solder lands under the IC when removing it. NOTE Masking is carried out on all the parts located within 10 mm distance from IC leads. Masking Tape (Cotton Tape) Blower type IC desoldering machine IC Tweezers Fig. 2-1 IC Fig. 2-3 2. Heat the IC leads using a blower type IC desoldering machine. (Refer to Fig. 2-2.) 4. Peel off the Masking Tape. NOTE 5. Absorb the solder left on the pattern using the Braided Shield Wire. (Refer to Fig. 2-4.) Do not add the rotating and the back and forth directions force on the IC, until IC can move back and forth easily after desoldering the IC leads completely. NOTE Do not move the Braided Shield Wire in the vertical direction towards the IC pattern. Blower type IC desoldering machine Braided Shield Wire Soldering Iron IC IC pattern Fig. 2-2 B2-1 Fig. 2-4 DISASSEMBLY INSTRUCTIONS 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin-tip Soldering Iron. (Refer to Fig. 2-8.) INSTALLATION 1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily. (Refer to Fig. 2-5.) Thin-tip Soldering Iron IC Soldering Iron Fig. 2-8 5. Finally, confirm the soldering status on four sides of the IC using a magnifying glass. Confirm that no abnormality is found on the soldering position and installation position of the parts around the IC. If some abnormality is found, correct by resoldering. Solder temporarily Solder temporarily Fig. 2-5 2. Supply the solder from the upper position of IC leads sliding to the lower position of the IC leads. (Refer to Fig. 2-6.) Solder IC NOTE When the IC leads are bent during soldering and/or repairing, do not repair the bending of leads. If the bending of leads are repaired, the pattern may be damaged. So, be always sure to replace the IC in this case. Soldering Iron Supply soldering from upper position to lower position Fig. 2-6 3. Absorb the solder left on the lead using the Braided Shield Wire. (Refer to Fig. 2-7.) NOTE Do not absorb the solder to excess. Soldering Iron IC Braided Shield Wire Fig. 2-7 B2-2 SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 1 second. Set Key Remocon Key VOL. (-) MIN 0 Releasing of V-CHIP PASSWORD. 1 Initialization of the factory. NOTE: Do not use this for the normal servicing. If you set a factory initialization, the memories are reset such as the channel setting, and the POWER ON total hours. VOL. (-) MIN VOL. (-) MIN Operations POWER ON total hours is displayed on the screen. Refer to the "CONFIRMATION OF HOURS USED". 6 Can be checked of the INITIAL DATA of MEMORY IC. Refer to the "WHEN REPLACING EEPROM (MEMORY) IC". VOL. (-) MIN 8 Writing of EEPROM initial data. NOTE: Do not use this for the normal servicing. VOL. (-) MIN 9 Display of the Adjustment MENU on the screen. Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment). CONFIRMATION OF HOURS USED POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: If you set a factory initialization, the total hours is reset to "0". ADDRESS DATA 1. Set the VOLUME to minimum. 2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second. Initial setting content of MEMORY IC. INIT 00 50 3. After the confirmation of using hours, turn off the power. POWER ON total hours. CRT ON 0010 = (16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value) FIG. 1 WHEN REPLACING EEPROM (MEMORY) IC If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. NOTE: No need setting for after INI 1F due to the adjustment value. INI +0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F 00 50 E8 0A 45 5E B3 24 B7 3D AC 0A 04 40 40 40 7F 10 50 00 00 00 00 00 00 00 3F 0F 0D C2 94 88 42 00 Table 1 1. Enter DATA SET mode by setting VOLUME to minimum. 2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second. ADDRESS and DATA should appear as FIG 1. 3. ADDRESS is now selected and should "blink". Using the VOL. UP/DOWN button on the remote, step through the ADDRESS until required ADDRESS to be changed is reached. 4. Press ENTER to select DATA. When DATA is selected, it will "blink". 5. Again, step through the DATA using VOL. UP/DOWN button until required DATA value has been selected. 6. Pressing ENTER will take you back to ADDRESS for further selection if necessary. 7. Repeat steps 3 to 6 until all data has been checked. 8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. After the data input, set to the initializing of shipping. 9. Turn POWER on. 10. Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 1 second. 11. After the finishing of the initializing of shipping, the unit will turn off automatically. The unit will now have the correct DATA for the new MEMORY IC. C-1 ELECTRICAL ADJUSTMENTS 1. BEFORE MAKING ELECTRICAL ADJUSTMENTS 2. BASIC ADJUSTMENTS 2-1: CONSTANT VOLTAGE Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. 1. Place the set with Aging Test for more than 5 minutes. 2. Set condition is AV MODE without signal. 3. Using the remote control, set the brightness and contrast to normal position. 4. Connect the digital voltmeter to the TP003. 5. Adjust the VR502 until the digital voltmeter is 115 ± 1V. CAUTION • Use an isolation transformer when performing any service on this chassis. • Before removing the anode cap, discharge electricity because it contains high voltage. • When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position. • When you exchange IC and Transistor for a heat sink, apply the silicon grease on the contact section of the heat sink. Before applying new silicon grease, remove all the old silicon grease. (Old grease may cause damages to the IC and Transistor.) 2-2: CUT OFF 1. Place the set with Aging Test for more than 15 minutes. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (01) on the remote control to select "CUT OFF". 3. Adjust the Screen Volume until a dim raster is obtained. 2-3: WHITE BALANCE NOTE: Adjust after performing CUT OFF adjustment. Prepare the following measurement tools for electrical adjustments. 1. Place the set with Aging Test for more than 10 minutes. 2. Receive the gray scale pattern from the Pattern Generator. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (10) on the remote control to select “R. DRIVE”. 5. Press the CH. UP/DOWN button on the remote control to select the “R. BIAS”, “G. BIAS”, “B. BIAS”, “R. DRIVE” or “B. DRIVE”. 6. Adjust the VOL. UP/DOWN button on the remote control to whiten the R. BIAS, G. BIAS, B. BIAS, R. DRIVE, and B. DRIVE at each step tone sections equally. 7. Perform the above adjustments 5 and 6 until the white color is looked like a white. 1. Oscilloscope 2. Digital Voltmeter 3. Multi-sound Generator 4. Pattern Generator On-Screen Display Adjustment 1. In the condition of NO indication on the screen. Press the VOL. DOWN button on the set and the Channel button (9) on the remote control for more than 1 second to appear the adjustment mode on the screen as shown in Fig. 1-1. TV 2-4: FOCUS 00 OSD 1. Receive a broadcast. 2. Turn the Focus Volume fully counterclockwise once. 3. Adjust the Focus Volume until picture is distinct. 34 Fig. 1-1 2-5: HORIZONTAL POSITION 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (03) on the remote control to select "H.PHAS". 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on right and left becomes minimum. 2. Use the Channel UP/DOWN button or Channel button (09) on the remote control to select the options shown in Fig. 1-2. 3. Press the MENU button on the remote control to end the adjustments. NO. 00 01 02 03 04 05 06 07 08 09 10 11 12 FUNCTION OSD H CUT OFF H.VCO H.PHASE AFC GAIN V.SHIFT H.SIZE V.SIZE V.LINEARITY VS CORRECTION R DRIVE B DRIVE R BIAS NO. 13 14 15 16 17 18 19 20 21 22 23 24 25 FUNCTION G BIAS B BIAS BRIGHT MAX BRIGHT CENT BRIGHT MIN CONTRAST MAX CONTRAST CENT CONTRAST MIN COLOR MAX COLOR CENT COLOR MIN TINT SHARPNESS NO. 26 27 28 29 30 31. 32. 33. 34. 35. FUNCTION CB DELAY FINE CR DELAY FINE CB PEDESTAL ADJ CR PEDESTAL ADJ E/W PARABOLA E/W CORNER E/W TRAPEZIUM LEVEL SEPARATION 1 SEPARATION 2 2-6: VERTICAL POSITION 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Check if the step No. V. SHIFT is "02". 4. Adjust the VR401 until the horizontal line becomes fit to the notch of the shadow mask. Fig. 1-2 D-1 ELECTRICAL ADJUSTMENTS 2-7: VERTICAL SIZE 2-10: SUB TINT/SUB COLOR 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (07) on the remote control to select "V.SIZE". 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes 9 ± 2%. 5. Receive a broadcast and check if the picture is normal. 1. Receive the color bar pattern. (RF Input) 2. Connect the oscilloscope to TP806. 3. Using the remote control, set the brightness, contrast, color and tint to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (24) on the remote control to select “TINT”. 5. Press the VOL. UP/DOWN button on the remote control until the section “A” becomes a straight line (Refer to Fig. 2-1). 6. Connect the oscilloscope to TP804. 7. Press the CH DOWN button 2 times to set to “COL. CENT” mode. 8. Adjust the VOLTS RANGE VARIABLE knob of the oscilloscope until the range between white 100% and 0% is set to 5 scales on the screen of the oscilloscope. 9. Press the VOL. UP/DOWN button on the remote control until the red color level is adjusted to 120 ± 10% of the white level. (Refer to Fig. 2-2) 10. Receive the color bar pattern. (Audio Video Input) 11. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 2~9. 12. Press the TV/VIDEO button on the remote control to set to the CS mode. 13. Activate the adjustment mode display of Fig. 1-1 and press the channel button (24) on the remote control to select “TINT”. 14 Press the VOL. UP/DOWN button on the remote control until the tint step No. becomes “53”. 15. Press the CH DOWN button 2 times to set to “COL.CENT” mode. 16. Press the VOL. UP/DOWN button on the remote control until the color step No. becomes “69”. 2-8: VERTICAL LINEARITY NOTE: Adjust after performing adjustments in section 2-7. After the adjustment of Vertical Linearity, reconfirm the Vertical Position and Vertical Size adjustments. 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (08) on the remote control to select "V.LIN". 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes minimum. 2-9: SUB BRIGHTNESS 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (16) on the remote control to select “BRI. CENT”. 2. Press the VOL. UP/DOWN button on the remote control until the brightness step No. becomes “98”. 3. Receive a broadcast and check if the picture is normal. 4. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 1~3. 5. Press the TV/VIDEO button on the remote control to set to the CS mode. Then perform the above adjustments 1~3. “A” Fig. 2-1 100% White 100% RED Level D-2 Fig. 2-2 ELECTRICAL ADJUSTMENTS 2-11: SUB CONTRAST 2-13: LEVEL 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (18) on the remote control to select "CONT.MAX". 2. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "81". 3. Receive a broadcast and check if the picture is normal. 4. Press the TV/VIDEO button on the remote to set to the AV mode. 5. Activate the adjustment mode display of Fig. 1-1 and press the channel button (18) on the remote control to select "CONT.MAX". 6. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "84". 7. Receive a broadcast and check if the picture is normal. 8. Press the TV/VIDEO button on the remote to set to the CS mode. 9. Activate the adjustment mode display of Fig. 1-1 and press the channel button (18) on the remote control to select "CONT.MAX". 10. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "86". 11. Receive a broadcast and check if the picture is normal. 1. Receive the monoscope pattern (70dB). 2. Connect the AC voltmeter to pin 6 of CP101. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (33) on the remote control to select "LEVEL". 4. Press the VOL. UP/DOWN button on the remote control until the AC voltmeter is 85 ± 2mV. 2-14: Confirmation of Fixed Value (step No.) Please check if the fixed values of the each adjustment items are set correctly referring below. NO. 00 02 04 05 06 09 15 17 19 20 21 23 25 26 27 28 29 30 31 32 2-12: SEPARATION 1, 2 Please do the method (1) or method (2) adjustment. Method (1) 1. Set the multi-sound signal generator for each different Lch and R-ch frequency (Ex. L-ch=2KHz, R-ch=400Hz) and receive the RF. 2. Connect the oscilloscope to the Audio Out Jack. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (34) on the remote control to select “SEP 1”. 4. Press the VOL. UP/DOWN button on the remote control to adjust it until the audio output wave becomes a fine sine wave. 5. Press the CH UP button once the set to “SEP 2” mode. Then perform the above adjustment 4. Method (2) 1. Set the multi-sound signal generator L-ch=1KHz, R-ch =Non input and receive the RF. 2. Connect the oscilloscope to the Audio Out Jack (R-ch). 3. Press the AUDIO SELECT button on the remote control to set to the stereo mode. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (34) on the remote control to select “SEP 1”. 5. Press the VOL. UP/DOWN button on the remote control to adjust it until the R-ch output becomes minimum. 6. Set the multi-sound signal generator L-ch=Non input, R-ch=1KHz and receive the RF. 7. Connect the oscilloscope to the Audio Out Jack (L-ch). 8. Activate the adjustment mode display of Fig. 1-1 and press the channel button (35) on the remote control to select “SEP 2”. 9. Press the VOL. UP/DOWN button on the remote control to adjust it until the L-ch output becomes minimum. D-3 FUNCTION OSD H H.VCO AFC GAIN V.SHIFT H.SIZE VS CORRECTION BRIGHT MAX BRIGHT MIN CONTRAST CENT CONTRAST MIN COLOR MAX COLOR MIN SHARPNESS CB DELAY FINE CR DELAY FINE CB PEDESTAL ADJ CR PEDESTAL ADJ E/W PARABOLA E/W CORNER E/W TRAPEZIUM STEP NO. 25 03 04 02 01 38 125 75 50 18 90 00 40 00 00 08 08 31 31 31 ELECTRICAL ADJUSTMENTS 3-3: STATIC CONVERGENCE 3. PURITY AND CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE 1. Receive the crosshatch pattern from the color bar generator. 2. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 3. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 1. Turn the unit on and let it warm up for at least 30 minutes before performing the following adjustments. 2. Place the CRT surface facing east or west to reduce the terrestrial magnetism. 3. Turn ON the unit and demagnetize with a Degauss Coil. 3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) 1. Tighten the screw for the magnet. Refer to the adjusted CRT for the position. (Refer to Fig. 3-1) If the deflection yoke and magnet are in one body, untighten the screw for the body. 2. Receive the green raster pattern from the color bar generator. 3. Slide the deflection yoke until it touches the funnel side of the CRT. 4. Adjust center of screen to green, with red and blue on the sides, using the pair of purity magnets. 5. Switch the color bar generator from the green raster pattern to the crosshatch pattern. 6. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 7. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 8. Adjust the crosshatch pattern to change to white by repeating steps 6 and 7. 3-4: DYNAMIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-3. 1. Adjust the differences around the screen by moving the deflection yoke upward/downward and right/left. (Refer to Fig. 3-2-a) 2. Insert three wedges between the deflection yoke and CRT funnel to fix the deflection yoke. (Refer to Fig. 3-2-b) RGB RGB R G B R G B UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT 3-2: PURITY Fig. 3-2-a NOTE Adjust after performing adjustments in section 3-1. 1. Receive the green raster pattern from color bar generator. 2. Adjust the pair of purity magnets to center the color on the screen. Adjust the pair of purity magnets so the color at the ends are equally wide. 3. Move the deflection yoke backward (to neck side) slowly, and stop it at the position when the whole screen is green. 4. Confirm red and blue color. 5. Adjust the slant of the deflection yoke while watching the screen, then tighten the fixing screw. WEDGE WEDGE WEDGE WEDGE POSITION DEFLECTION YOKE DEFLECTION YOKE SCREW MAGNET SCREW Fig. 3-2-b PURITY MAGNETS 6 POLE MAGNETS 4 POLE MAGNETS Fig. 3-1 D-4 ELECTRICAL ADJUSTMENTS 4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION) CRT CRT PCB R804 CP803 J801 TP806 CP852 TP804 CD852 R808 CD803 CP804 CP852B VM COIL PCB CP802B CP801B CP851B CD801 CD851 CD802 CP801A CP101 J708 J704 J703 J702 J701 TU001 FB401 TP003 VR401 W003 CRT VR502 CP851A CRT CP802A SPEAKER CP502 CD1001 CP501 CP1001 OS101 MAIN PCB CD501 AC IN D-5 J705 J706 J707 J1001 BLOCK DIAGRAM A/V OUT J708 6 COMB IC IC1501 LA76600M 4 Q852, Q583 CHROMA IC IC601 M611283FP 2 AMP Q610 16 Y OUT 60 AMP 18 C OUT Y IN 3 DELAYDE Y OUT 58 VIDEO LINE OUT Q603, Q614, Q605 LINE1(REAR) J701 6 Vin1 V.OUT 3 Vin2 4 4 VIDEO SW(C) IC IC1503 MM1501XNRE 6 Vin1 V.OUT 6 4 3 2 2 B OUT 16 FRONT -VIDEO J705 2 2 CVBS2 6 38 CVBS3 3 53 CVBS4 H OUT 8 H.DRIVER R IN 23 34 RED R 40 V IN(YUV) FAST BLK 24 TU001 FRONT-AUDIO.L J706 33 BLANK X602 3.97545MHz 1 5 DY OS101 REMOCON 9 1 D101 ON_TIMER 10 X.IN 19 30 SCL1 X.OUT 30 31 SDA1 KEY1 6 POWER X101 8MHz VOL DOWN CH DOWN VOL UP CH UP SPEAKER SP1001 5 SDA SCL MEMORY IC IC199 S-24C16AFJA-TB-01 SPEAKER SP1002 2 7 18 AUDIO SW(R) IC IC702 MM1501XNRE 6 19 23 2 21 3 16 20 14 2 12 22 30 19 1 7 5 7 Vin2 Q901 Q902 V-OUT IC IC401 LA78040 14 3 V.OIT 2 CRT V801 KEY2 7 SCL 6 2 XTAL 3.58 34 SDA HV 6 STEREO IC IC902 AN5829S 24 V.OIT 2 S MICON IC101 OEC7090A 5 6 Vin1 7 H.OUT 36 BLUE B 27 F Q405 B IN 21 26 F 63 44 U IN(YUN) 10 1 11 3 13 4 RED AMP 35 GREEN G AUDIO SW(L) IC IC702 MM1501XNRE 6 Vin1 Q801, Q810 G IN 22 17 FRONT-AUDIO.R J707 GREEN AMP 48 Y IN(YUV) 11 Vin2 Q802, Q811 2 YUV_IN(REAR) J704 J801 8 Q402 42 4 V OUT Vin2 46 LINE2(REAR) J703 2 R OUT 14 49 C IN(Y/C) CVBS1 2 G OUT 15 51 Y IN(Y/C) BLUE AMP VM COIL FB401 Q803, Q812 VIDEO SW(Y) IC IC1502 MM1501XNRE S-JACK J702 SVM OFF BUFFER BUFFER Q613 SVM Q855, Q856 Q857, Q858, Q859 Q854 BUFFER TONE IC IC302 AN5891SA-E1V BBE IC IC301 NJM2150AM SOUND AMP IC1001 AN5276 3 HEADPHONE_JACK J1001 4 5 1 BUFFER E-1 E-2 R438 L402_1 C420 W059 C707 W130 R433 W009 W010 W011 B403 C409 VR401 C417 R421 R429 R436 C710 C1004 C1003 C708 R437 08 W821 TP004 W019 D415 R420 R416 R517_1 D513 C1007 C1011_1 C1009 W002 W136 R544 D524 D509 R506 W817 R553 R554 C403 R527 R536 C618 C642 C507 C512 R502 B504 W027 W004 C605 D602 L1508 W801 D512 C504 R524 C611 C610 W147 R603 W148 W149 C1532 L1501 W154 W151 W152 W150 W155 W858 C621 R535 C406 C408 B405 R414 R413 C407 C622 C1008 C1002_1 C1001_1 B501 R540 W825 C520 C527 CP851A R001 R002 W024 X602 W082 C609 02 C601 C1510 W848 C1518 R6 C608 C645 C630 C627 R657 C603 C1520 C1528 L1505 D523 D503 R539 C501 D516 W013 D520 W043 W042 W806 D501 CP508 C502 C519 _1 W031 W033 W035 W032 W037 W038 W040 R132 R124 W030 W097 W103 W805 W106 W107 W108 W099 W112 W114 W100 D605 D606 C513_1 D105 C901 C902 C304 C317 C321 C319 R313 W158 W052 D106 W054 W822 W053 R140 R139 W128 R520 C114 R118 W120 W123 D114 C910 C108 R120 R102 C905 C916 W116 D116 C907 C904 W117 W175 C302 C308 C305 R301 W179 W177 C327 C316 C314 C318 W174 C903 C914 L901 R913 W124 R119 W127 W129 W126 C306 C333 R304 R303 W178 C329 C332 W811 D108 D110 R151 C109 C122 CP502 R500 D104 D107 W093 C919 W092 R130 W028 C113 W159 C623 L601 C330 W161 W160 C328 C110 TH501_2 C139 W165 W163 W164 R902 R901 W096 W095 W098 W104 W109 W101 W102 W111 W105 D607 W168 L1512 R623 R626 R614 W170 W110 W169 W184 C638 W113 C629 C615 D604 C606 C602 C1502 W166 L1503 W804 L1502 C1525 C1501 C1530 RISK OF FIRE - REPLACE AS MARKED. R430 R432 C418 L401 C410 R402_1 C702 TP003 C1005 W071 W835 C1535 L1511 FH501 F501 FH502 SW105 R542 W156 CP501 R515 D504 CP507 D404 C415_1 B402 C430 R441 W018 C711 R701 C705 C733 C701 W812 W137 W138 D511 D502 T501 50 W001 W007 W065 C728 W063 W064 W135 D709 D608 C001_1 TU001 W133 D706 W006 R443 C427 F-2 F-1 SW102 SW101 SW104 SW103 OS101 J705 J706 J707 R146 W121 D109 J1001 D115 R1002 C505_1 W049 W118 R133 X101_1 W122 W176 L301 W055 R302 L501 W180 W119 CP1001 R1001 W125 W056 W829 W830 R904 W094 C503 W039 R601 W091 W157 D514 C506_1 W162 R905 W181 CP802A W029 W167 RY501 D525 D508 D517 Q504 R547 W047 D528 R501 R426 W048 W080 W115 R452_1 W044 W041 Q611 W172 W171 D505 Q508 Q601 R541 R512 W081 W139 Q402 R510 W046 W045 W173 L1510 W022 R546 T401_1 W084 R537 D414 D510 W083 D406 W140 B401 D507 Q514 C535 W005 D506 R508 C509 R434 R406 Q505 R505 C402 Q509 W023 R648 W090 Q607 W026 W025 W141 W815 C521 D601 Q502 W089 W088 R616 HS501 R545 C524 Q503 R543 Q507 R428 R1009 R507 W067 VR502 HS402 W069 _1 W020 R418 Q405 D410 C5 FB401 D402 W073 W072 R439 CP401 R427 W003 IC401 W185 W186 W074 R702 W021 W075 Q512 D610 Q604 W143 R649 Q602 D611 Q606 D603 W144 W145 W078 D403 TP005 W077 W076 R422 W079 C517 W146 W057 W820 W061 W813 W058 W819 C425 R710 W060 W131 R410_1 W183 W068 HS1001 W062 W850 W132 D702 W134 TP006 D001 J703 J701 IC504 W070 W803 IC1001 D705 D704 CP801A D411 CP101 D407 D405 C413_1 J708 J704 D701 D703 C426 J702 C5 PRINTED CIRCUIT BORADS MAIN (INSERTED PARTS) SOLDER SIDE R730 F-3 Q711 R516 Q709 C640 R1523 R610 R1510 Q605 Q614 R621 R1529 R1508 Q1001 R1010 R1011 C1010 C1012 R705 C1508 R1502 R1516 R1518 R1520 C1533 R311 C326 R308 C324 R306 R644 C1512 C1514 R1512 C1516 Q1508 Q1504 R655 IC1502 C1519 IC1501 C1504 C1505 C315 C320 R906 R1503 Q1503 R1506 C1513 R1530 C1531 C1517 R1505 C1509 C1507 C1503 C1506 R645 C625 C633 R624 R643 R314 C323 R305 R310 C325 R309 R307 R312 C322 IC302 R1528 R1504 R1522 C307 C309 C310 C313 C301 C1521 Q603 R642 Q613 C634 C636 C303 R1003 R609 R607 C1523 49 R651 R620 C915 C142 C918 C144 C604 R646 R647 C912 C334 C311 R907 C1515 R1509 1 C005 C628 R635 R641 R619 Q902 R1004 C607 R519 R611 IC902 C738 R653 R652 R606 R608 R604 C635 R613 R612 R605 R636 C911 R706 17 C616 R654 C612 R903 C102 R729 R733 C725 R709 R912 C917 R726 C736 C706 1 33 60 IC R629 C140 C908 C741 R746 C742 R745 C719 C734 R735 R736 C614 C641 R634 C913 R724 R739 Q712 R622 R145 C135 R134 C141 R110 IC199_1 C724 C727 C722 C439 C632 C631 R628 C143 C137 C138 C624 R617 C136 R625 Q103 R728 R727 C735 R417 R136 R632 R128 R127 R142 R141 R143 R129 R150 R703 R511 R618 C644 C637 IC101 R135 C115 R627 C643 R131 C131 C146 R122 C120 C145 R126 R101 R708 R725 R704 R401 C106 R138 R125 C119 C111 C121 C117 R114 R112 R113 C416 R453 R525 R103 R106 R109 C619 R711 R513 C104 R415 C510 C511 R532 R533 Q101 C737 R734 R721 C411 C405 C554 C541 PRINTED CIRCUIT BORADS MAIN (CHIP MOUNTED PARTS) SOLDER SIDE C720 C312 Q901 IC301 Q610 R1519 C1526 Q1507 R1507 IC1503 R615 R407 R1013 R006 IC702 IC701 C002 R404 F-4 Q803 D803 R830 W001 CP804 C821_1 R874 R869 C861 R867 W811 D857 C863_1 C852 C858 W004 C860 B851 R880 R873 R878 CP852B S852 C864 C865 W006 B853 L804 Q801 R828 W802 C8 08 L802 D801 R829 Q802 R875 CP803 Q857 W009 B852 Q856 L803 R871 D856 C859 R813 R810 R872 R879 D854 R866 R815 R811 C804 D802 R864 R865 R870 C854 J8 HS851 S851 CP852 R881 R817 C806 R821 C856 R862 R858 R863 R861 R860 D852 R854 R853 C855 C853 01 C862_1 R868 D853 R876 R818 W805 R856 W810 R859 R822 W809 C813 W003 R857 R855 Q854 R804 W820 W008 CP851B D858 Q858 D806 C809 CP802B Q859 Q852 F-6 F-5 R877 C857 W806 R819 R814 C805 Q853 Q812 W807 R806 TP805 D808 R820 R812 R809 R808 W804 Q811 W007 W808 D805 TP804 D807 Q810 CP801B D804 Q 85 5 PRINTED CIRCUIT BORADS CRT/VM COIL SOLDER SIDE D809 TP806 D855 A B C D G H 8 (MAIN PCB) B+ 3 LED SW Q101 KTC3875S_Y_RTK Vout 2.7 1 R120 5.0 0 4.9 TEST POINT R109 0 C108 POWER ON D109 SLR-342VCT32 GND 2 1K 0 16V 10 KA R102 OS101 RPM7138-H5 270 1/4W TM101 R25-1911 47 1/4W BT001 R03(AB)E_20_T BT002 R03(AB)E_20_T F MICON SCHEMATIC DIAGRAM ACCESORY 8 E CP101 7 R101 2 I2C_SDA 3 I2C_OFF 4 GND 5 0 NC R110 BBE_SW 0 10K 42 EXT MUTE H_CTL PROTECT 12C_OFF VOLUME BBE SW 41 AUDIO MUTE 40 TV_MUTE 1K 1K 47K 1/4W 4.2 0.1 R122 R124 1K 1/4W R150 SYNC C120 0 0 FROM/TO CHROMA CLAMP_OFF 33P CH SYNC_OUT 0 100 HD VD 5.0 OSD_Y OSD_B C144 2.1 OSD_G GREEN G RED R ON_TIMER BLANK D107 35 34 REMOCON 0 0 C131 150P CH 0 NC FROM/TO DEFLECTION 3.5 X-RAY TEST CNVSS C138 0.1 B C137 SW_Y_OUT 6.8K R128 SDA SCL 6.8K R129 MCU_CLOCK 10P CH R143 1.5K R142 1.5K R141 5.0 NC 1SS133 R145 D105 W811 2.2K C135 0 FROM/TO TUNER/STEREO J_AUDIO_OUT_R R139 0 R135 J_AUDIO_OUT_L 4.7K 100 1/4W R140 5.0 R136 5.0 SDA 4 100 1/4W 2 3 FROM/TO SOUND 5.0 R134 10K SDA SCL 14.6 X-RAY 27 RESET 5.0 C115 CLOCK CONT CVIN VHOLD 26 D106 MTZJ5.1B C106 0.1 B 3.2 NC FSC IN 25 5.0 X-RAY 1 1.7 FILT X.OUT R138 C113 C111 2.0 VSS VCC 24 R132 0.1 B R131 2.0 1K 1.0 1M 100 1/4W C122 C119 50V 1 KA D115 1SS133 D114 220P CH C121 R125 C117 10 0 21 27P CH HLF 22 POWER X.IN 23 X101_1 8MHz 100CT8R005 27P CH C104 GND 19 2.3 DEGAUSS_H 20 C102 820P CH 2.4 0.001 B P.FAIL 3 4 SCL 4.7K H_CTL FROM/TO POWER 5 RESET POWER 1.5K 32 33 POWER NC DEGAUSS H 31 SCL1 AUDIO_SW P FAIL 30 11 12 SDA1 29 5.0 CLOCK_CNT 28 4 Y/C_SW 13 0 14 CH S_IN 15 C141 220P 0 16 22K 1/4W AUDIO_SW 17 R119 CH 1SS133 6.8K 0 C140 220P 0.1 B R127 47K EXT_MUTE S_IN 9 5.0 18 FROM/TO AV R114 16V 10 KA C139 2.2 10 2.2K C136 D110 0 0.1 B OSD_BLK 4.8 1SS133 X RAY D104 D108 BLUE B OSD_R 4.0 1SS133 KEY 2 6 PROTECT C146 0.001 B R126 1SS133 38 V SYNC 37 5 KEY 1 36 5.0 6 5.0 2.2K R113 H SYNC 7 R112 AFT AFT 8 3.2 FROM/TO TUNER/STEREO 7 CLAMP SW Q103 KTC3875S_Y_RTK 150P CH 5 6 AUDIO R AT+5V 39 4.0 2.2K 1/4W 1 220P CH R118 2 FROM/TO SOUND 5.0 3 C143 R130 MICON IC IC101 OEC7090A 4 R146 220P CH 100 1/4W 220P CH C142 6 AUDIO L 7 C145 SW105 EVQ21505R POWER SW104 EVQ21505R 560 VOL DOWN 2.7K SW102 EVQ21505R CH DOWN SW103 EVQ21505R VOL UP SW101 EVQ21505R CH UP R106 1 I2C_SCL 560 R103 173979-7 GND 5.0 0.01 3 1SS133 D116 B MTZJ5.6B 47P CH R133 C109 FROM/TO COMB FILTER 0.1 1K 1/4W B 3 0 0 2 5.0 2 VCC 8 E0 E1 SCL 0 7 MEMORY IC IC199_1 S-24C16AFJA-TB-01 4 5.0 E2 W822 6 MODE 5.0 SDA 5 VSS C114 50V 0.47 KA 6.3V 2200 YK C110 R151 2 10K 1/4W Y/C_SW 0 1 0 PCB010 TMC559 NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. 1 A G-1 B C NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE D E 1 F G H G-2 A B C D E F G H CHROMA SCHEMATIC DIAGRAM (MAIN PCB) 8 FROM/TO AV 8 D610 VIDEO_IN2 SB290S V_IN[YUV] R616 VIDEO_IN1 8.8 4.9 120 1/2W U_IN[YUV] AT+5V REG Q607 KTC3203_Y 5.5 R617 Y_IN[YUV] 100 R OUT 10 11 12 13 14 0 0 5.5 0 NC 3.8 8.0 8.0 0 8.0 8.0 6.8K R622 16V 47 YK C622 15 4.0 4.0 32 31 30 29 28 27 26 25 24 23 22 21 20 17 ACL 3.3K 0 19 HI VCC 9 18 NC(GND) NC(Vcc) 8 MONITOR OUT R651 4.0 1K 100CT3R505 R634 C632 18P CH X602 3.579545MHz 8.2K C_APC MCU 5.7 VREG OUT CVBS3 NC(GND) 0.015 B C631 C630 50V 0.47 KA C627 C624 0.1 B V/C VCC V IN(YUV) 7 SW_Y_OUT 6 0 AT+5V NC 5.0 RESET 3.5 NC 5.0 POWER R627 3.5 SCL 100 3.5 R628 SDA 100 4.9 NC 4.2 C637 33P CH C643 33P CH C644 33P CH OSD_R 2.9 OSD_G 2.9 OSD_B 4.6 VD W805 4.9 HD 4.9 SYNC_OUT 2.1 R629 D608 6.8K 11E1-EIC OSD_Y 16 4 CLAMP_OFF 4.0 33K R632 KANP C638 16V 10 R625 5.6K 1SS133 D605 1SS133 D607 3.3K R653 3.3K R652 1SS133 D606 C629 16V 1000YK 0.01 B C628 1K 1K 1/4W R636 1.5K R615 R611 10K 120K TO CRT/SVM CP802A (CP802B) B2013H02-7P P.CON+8V 1 P.CON+5V GND(SIGNAL) 1K C623 R643 H.OUT H_SYNC 16V 100 YK R620 V_OUT 100 R623 100 1/4W R626 100 1/4W 3 G.OUT 4 B.OUT 5 CLAMP_OFF 6 VM COIL 7 CH 0.1 B C634 2 100P CH R647 0 4.7K 33uH C625 47P SVM OFF Q613 KTC3875S_Y_RTK 0 R646 R645 3.3K R642 10K R621 0.7 3 2 R.OUT C604 0 82P CH 1.4 16V 47 KANP 1K CD802 CU274201 C636 0.0082 B 5.3 SVM Q610 KTC3875S_Y_RTK 270 C633 C601 R619 560 L601 15K R624 R644 ABCL 2 5 OSD_BLK 2.9 R635 R614 R609 D604 NC(GND) CVBS1 49 50 51 52 53 C615 0.1 TF C612 11.3 8.5 100 6 56K MTZJ12B FROM/TO DEFLECTION 7.9 8.5 C602 C645 3 16V 100 YK 7.9 11.3 5 2 INV.FBP OUT 3.6 R654 0.01 B P.CON 8V REG Q601 KTC3209_Y 4 VRAMP CAP 3.2 P.CON 8V REG Q611 KTC3209_Y C609 15 1/2W GND C606 UNREG+12V B IN 0.33 TF R601 G IN 3 V OUT 1 16 B OUT V PULSE OUT VRAMP AGC CAP FROM/TO POWER 16V 47 YK 4 8.7 VREG OUT 2 AFC FILTER NC 4.0 VIDEO LINE OUT 15 G OUT NC 4.0 3.9K 330 R608 390 EW OUT R IN 1 HVCO F/B DEF VCC 4.0 R606 22P CH C635 1K R604 R613 DELAYDE Y OUT NC(Vcc) 8.7 FAST BLK H OUT 16V 47 YK FAST YUV SDA CLK CONT NC 10K 2.3 3.0 P_CON CONT CHROMA IC601 M61283FP 10K 1.7 3.8 330 R607 R605 3.8 2.2 7.3 3.0 NC 34 XTAL 3.58 SCL 50V 1 KA 7.9 6dB AMP Q603 KTC3875S_Y_RTK 6dB AMP Q605 KTC3875S_Y_RTK C608 NC C616 P.CON+8V[B] 6dBAMP Q614 7.8 KTA1504S_Y_RTK 7.3 fsc OUT PROTECT Y SW OUT 5.7V VREG OUT 6.8K FROM/TO SOUND 2.8 10 1/2W R648 P.CON+5V 48 Y IN(YUV) FBP IN 0 NC 0 0 33 MCU CLOCK OUT DEF GND2 0.01 F FROM/TO MICON 0 3.2 35 34 MCU RESET 33 V/C GND R641 R655 R657 3.2 7 NC 47 NC(GND) R612 P.CON+8V[B] 1K 1/4W TUNER+5V 16V 47 YK C603 TUNER_VIDEO C640 CVBS4 0 1.9 5.6 2.8 39 38 37 36 HVCO F/BDEF GND1 100 FROM/TO TUNER/STEREO 5 5.7 VREG VCC 0 1.9 5.0 1.2 43 42 41 40 LOGIC GND R610 0 1.2 45 44 0.01 B 5.5 1.9 Y IN(Y/C) 54 SB290S 5.5 P.CON 5V REG Q604 KTC3209_Y 7.2 8.7 55 5.0 50V 1 KA 56 D611 3.0 5.5 7.2 57 C642 5.0 P.CON 5V REG Q602 KTC3209_Y NC(GND) 58 3W 0 59 12 B 60 12 3W 0.1 61 R649 62 R602 FSC_OUT C IN(Y/C) 63 P.CON+8V[A] 2.2 C641 10K 1/4W 6 48 P.CON 5V REG Q606 KTC3209_Y 5.0 7.2 VIDEO_OUT 64 Y_V_OUT_SW 0 3.0 47 46 U IN(YUV) 2.7 NC(GND) P.CON+5V 50V 1 KA KA 50V 1 C621 C_V_OUT_SW CVBS2 C619 B C618 C614 0.1 B C611 B C610 C607 0.01 C605 16V 47 YK FROM/TO COMB FILTER 16V 47 YK D602 D601 MTZJ15B D603 1SS133 MTZJ8.2B 330 1/2W 50V 1 KA R603 0.1 7 50V 1 KA VIDEO_OUT R618 VIDEO_IN3 4.7K PCB010 TMC559 NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. 1 A G-3 B C NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE D PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES 1 DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES E ARE F G H G-4 A B C D E F G H DEFLECTION SCHEMATIC DIAGRAM (MAIN PCB) 8 8 FROM/TO DY V.OUTPUT IC IC401 LA78040 4.0 R433 25.0 17 1K 1/2W 12.0 7 R429 6 1K 1/2W 5 L402_1 R421 16 R407 VCC GND 2 3 4 4.0 25.0 2.0 0 1 C416 PUMP UP V801 A51LVV896X07(O) CP401 B06B-DVS 18 1K 1/2W 4.7K R401 + THERMAL PROTECTION AMP 100P CH - NC ELH5L4113 NC R439 1.2K 7 6 6 5 5 4 4 3 3 2 2 1 1 9 10 8 6 11 R G B 5 7 1 7 3 TO CRT/SVM R422 560 1/2W VR401 1K R418 560 1/2W V.POSI ADJ R427 680 1/2W 100V 0.22 MMTS C417 R437 2 CD803 (CP803) CP83035A 6 GND C420 FB401 TP004 PROTECTOR TEST TP003 2.8 13.1 W850 0 W4BRH3.5X6X1.0X2 HS402 763WAA0216 0.1 0.1 100 1/4W B403 B405 R428 5 1 2 0 26.3 4 23.8 H.OUT Q405 115 2SD2499(LBOEC1) W4BRH3.5X6X1 T401_1 ETH14Y47AY 0 3 C403 20 50V 22 YK 0 100V 0.01 MMTS C402 0.4 R406 10K R453 FROM/TO POWER H.DRIVE Q402 KTC3227_Y 17.3 W815 470 1/2W 5 250V 0.39 PMS 21 19 4.7mH 250V 0909 2.2 YK C418 ABCL R402_1 68 1/2W 1.25KV 0.013 MPP L401 C410 H_SYNC W813 0.001 CH W4BRH3.5X6X1 B401 C411 H.OUT B402 P.CON+5V W4BRH3.5X6X1 V_OUT 108.0 105.0 R434 0 +B 5.6 10W 0 FBT+B 4 1 2KV 0.001 R 1 1/2W MTZJ30B MTZJ30B C409 50V 10 YK D410 D403 C425 W821 R420 3.3 1/2W C408 50V 1 YK 820 18K +-1% R416 FROM/TO CHROMA 25V 1000 MHE 39K 2.7 1/2W D402 11E1-EIC C407 R417 C406 R415 560P CH R413 C405 R414 27K +-1% 6 35V100 YK 1K 1W R452_1 R410_1 D414 D415 11E1-EIC 11E1-EIC 150 2W 2 9 10 8 ANORD HV E180 B+ AFC HEA TER AU02A-EIC 0 FROM/TO CRT/SVM GND 8.2K 1/2W MTZJ5.1B 100 GND 0 11 ABL GND 7 8.1 4 R443 150K 1/2W C427 100V 0.1 MMTS C415_1 R430 500V33P SL 82K 1/2W D404 R432 SCREEN S 8 0.1 E8 NC 5 R404 FORCUS F E12 0.2 4 NC E27 2.0 3 D405 H+B 330 1W 1 6 5 FJN20A002 COL 3 D411 X-RAY TEST AU02A-B-EIC TO CRT/SVM C426 TP006 AU02A-EIC 100V 22 YK TP005 15K +-1% C430 1/4W +-1% 4.7K R426 D406 MTZJ5.6B 0.001 B C439 2 18K 1/4W +-1% CP801A (CP801B) B2013H02-5P MHE R441 C413_1 R436 X-RAY 250V 22 H_CTL 35V 1000 YK R438 FROM/TO MICON 2.7 2W D407 3 NC NC CD801 CU253401 180V 1 NC 2 NC 3 GND 4 HEATER 5 2 PCB010 TMC559 1 1 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. A G-5 B C THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY D ARE PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES E NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE. F G H G-6 A B C D E F G H POWER SCHEMATIC DIAGRAM 8 8 (MAIN PCB) RELAY DRIVE Q504 KTC3198 7 R515 0 10K 1/4W R502 R C524 SWITCHING0 Q514 R544 KTC3203_Y 100V 0.047 500V 0.001 B 2KV 0.001 330 2W 0 270 1/4W R542 D507 0.15 1W 1SS133 1SS133 D513 2KV 0.0015 R B504 0 240.0 12 NC R527 D510 W5RH3.5X5X1.0 FE201-6L49 5 10K 1/4W 115.2 STAND BY SW. Q505 2SC2909 0.68 2W R516 0 10K 0 FROM/TO TUNER/STEREO 13 P.CON+B 20.0 14 GND 3 2 26.0 15 1 16 138.9 C512 47K 1/4W W825 125.0 SWITCHING Q502 159.4 D 2SK3326(2) G 5.3 5.3 0 S 114.7 C517 10K 11 5 BL02RN1-R62 100V 2.2 YK R536 GND 115.1 82K 1/4W 6 115.5 FBT+B R513 W801 6.3A 125V +B R507 10 P2 H+B +B SW. Q503 2SA1371 R535 7 40.0 FROM/TO DEFLECTION R505 8140066S 25.0 1SS133 115.4 C539_1 0 B501 6 GND 100K 1/4W 3.9K 1/4W P1 141.6 C535 CURRENT DET. Q512 2SA1624 115.7 50.0 FH501 FH502 EYF-52BC EYF-52BC T6.3A_L_125V P.CON+12V R537 38 9 NC 8 6.3A125V 4 25V 1000 YK C501 D514 T501 1SS133 R539 1.2M 1/4W R540 D523 1.2M 1/4W D502 RM11C-EIC RM11C-EIC C507 200V470 UP 2 D503 1 R503 10K 1/4W 160V 220 YXF BLACK 4 2KV 0.001 R C521 BLACK 5 3 C503 D517 C511 1 1 F501 2KV 0.001 R SOUND+B 0.22 3W SOUND_GND 220P CH WHITE C502 R541 0.22 1W 1 7W RM11C-EIC WHITE C505_1 2 2 BLADE WIDE AC120V_60Hz CD501_1 0R615901 CP508 003P-2100 COIL,LINE FILTER L501 1R5A123F28Y RM11C-EIC 1 R520 B59203-S1060-B14 CP501 A3963WV2-3PD D501 CP507 003P-2100 1 TH501_2 C506_1 2 275V 0.22 1 1 2 6 R501 275V 0.1 ECQUL CP502 A1561WV2-2P R517_1 W806 30DF6-FC ECQUL R500 4 1.5M 1/2W 3 DEGAUSS COIL L503 8R200024 FROM/TO SOUND D505 MTZJ18B 1 2.7M 1/2W +-10% 2 C519_1 C513_1 RY501 ALKS321 250V 0.001 KX 0 250V 0.001 KX 10.9 1SS133 D504 D516 7 MMTS FROM/TO CHROMA HS501 763WAA0244 4 UNREG+12V GND FROM/TO MICON R524 P.FAIL DEGAUSS_H POWER D506 GND 100 1/4W 1N4937 3 D512 R532 12.9 R511 1.5K 22K C527 16V 2200 YK D520 1SS133 CP851A (CP851B) CD851 B2013H02-4P CU244201 C550 12.9 16V 1000 YK 12.8 R512 MTZJ12B 100 1/4W R547 C508_1 IS THE LIVE CONNECTION 250V 0.0022 KX MTZJ3.9B 21DQ09N D525 CAUTION: R510 TO CRT/SVM P.CON+12V SW. Q508 KTA1271_Y 0.8 STAND BY SW. Q509 KTC3198 NC 1K 1/2W 1K 1/4W 25V 47 YK R543 C509 C541 0.056 B C520 500V 0.001 B GND1 100 1/4W X-RAY 15K 3.3K 1/4W R525 C504 1001/4W 3 2 R508 MTZJ18B 1.5 270 R533 FEED BACK SWITCHING Q507 KTC3198 D508 6.8K 1/2W R553 R554 100K 1/2W R506 6.8K 1/4W +B ADJ 2 VR502 22K D528 W817 5.7 MTZJ5.6B 6.3 3 9.7 1SS133 R546 4 D509 9.7 150 1/4W D511 1N4937 C554 0.022 B D524 16.3 1 10.7 R545 50V2.2 YK FEED BACK IC504 LTV-817M-VB 0.7 R519 P.CON+B 4 NC 3 GND 2 P.CON+12V 1 FROM/TO AV 10K P.CON+12V 0 2 GND FROM/TO COMB FILTER GND PCB010 TMC559 6.3A 125V 1 CAUTION:FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE 6.3A 125V(F501). UNE PROTECTION CONTINUE LES RISQUES D’INCEIE ATTENTION:POUR N’UTILISER QUE DES FUSIBLE DE MEME TYPE 6.3A 125V(F501). A B NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. C THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES ARE PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES DESCRIBED IN PARTS LIST ONLY D E 1 NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE. F G H A B C D E F G H SOUND SCHEMATIC DIAGRAM 8 8 YK C319 50V 10 YK R305 Balance /MUTE + 0 NC C318 R OUT SDA SCL 19 18 17 0 NC 4.0 3.5 3.5 C316 4.8 R303 4.8 2 C325 20K 0.033 B 4.8 3 4.8 4 4.8 5 4.8 6 4.8 0 7 8 8.9 9 8.9 R313 1K 1/4W 10 6 8.9 BBE 20 4.8 100 1/4W 50V 10 YK C314 1 R307 R304 4.8 18 4.8 17 4.8 16 4.8 15 R306 R308 20K 20K C326 C324 0.0033 B 0.033 B 4.8 14 4.8 13 R311 C320 12 9.5 0 11 5 C330 C328 100 1/4W 19 0.1 B C311 50V 10 YK 0.01 B C312 1B C308 NC 20 BBE IC NJM2150AM NC 21 C323 20K 0.0033 B 10K 16 C332 VD L ONT 16V10 KA BD 16V10 KA 4.0 15 0.01 B C303 C321 50V 10 YK C313 0.01 B C310 0.033 B C317 2.9 14 IC301 4.0 50V 10 YK C302 2.0 + NC BB RB RT BLD TD 27 26 25 24 23 22 0 NC 4.0 4.0 4.4 3.0 2.0 100uH 0305 C306 NC 13 NC 56P CH 4.5 NC 28 0 NC P.CON+8V[B] 16V 100 YK LB 0 56P CH C322 29 L301 FROM/TO COMBI FILTER LT NC 12 NC 50V 10 YK Vref 30 C305 5 0 11 Volume 2.2K Control Control R IN 31 7.9 4.0 10 4.8 MODE control VCC 32 PF3 4.0 9 GND Tone SURR + PF2 0 8 PF4 16V100 YK AGC 7 10K R312 L IN 3.9 6 50V10 YK AGC 5 NC R310 PF1 4 NC 0.039 B 3.9 3.9 16V10 KA C329 3 NC 0 10K C327 2 NC 10K 1 2.3 FROM/TO CHROMA 0 R309 3.0 C334 1.7 C309 50V 10 YK TONE CONTROL IC302 AN5891SA-E1V 3.9 6 50V 10 YK 7 50V10 YK 2.7K 1/4W C304 C301 SW_AUDIO_R R301 2.7K 1/4W 0.033 B 22 50V 10 R302 23 SW_AUDIO_L 0.1 B C315 C307 FROM/TO TUNER/STEREO 7 0.015 B R314 220K C333 50V 10 YK (MAIN PCB) GND FROM/TO MICON SDA SCL 4 4 BBE_SW SOUND AMP IC IC1001 AN5276 TV_MUTE + - + ATT. + + RIPPLE FILTER CH1 CH2 GND NC RF IN IN 1 2 3 4 5 0 NC 0.2 16.0 0 0.2 FROM/TO POWER 25 ATT.CONT. 24 CP1001 A2502WV2-4P VOL CH2 VOL MUTE OUT 6 7 8 9.6 0.7 3.7 STAND CH1 GND VCC -BY OUT 9 10 11 12 0 16.5 12.7 15.2 SOUND+B 3 4 4 3 3 2 2 1 GND P.CON+12V C1001_1 R1003 SOUND_GND 50V 1 50V1 KA 25V1000 C1004 YK 15K YK C1002_1 C1009 R1013 7 26 50V22 YK C1007 R1002 50V2.2 YK 0 C1008 25V330 YK C1011_1 W835 C1005 220P B R1009 MUTE 10K 1/4W Q1001 KRC111SRTK 3.6 0 3 HEADPHONE JACK J1001 MSJ-2000 10K 2 (R) SP1002 SG05K07BRA 8 OHM 5W 2.5W KA R1004 25V1000 C1003 25V1000 YK 0.0047 B 10K C1010 10K R1010 W858 0.0047 B R1011 C1012 15K SP1001 SG05K07BRA 8 OHM 5W (L) 2.5W SPEAKER 1 CD1001 CU14411A W803 SPEAKER 2 6 2 R1001 270 1/2W 27 3 HS1001 763WAA0215 270 1/2W 4 5 1 PCB010 TMC559 CAUTION: DIGITAL TRANSISTOR 1 NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. A G-9 B NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES ARE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES DESCRIBED IN PARTS LIST ONLY C D 1 PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE E F G H G-10 A B C D E F G H TUNER/STEREO SCHEMATIC DIAGRAM 8 8 (MAIN PCB) TU001 20 VIDEO OUT 16 IF OUT FROM/TO CHROMA 17 15 BT 14 SIF OUT AUDIO OUT 13 12 AFT 11 SDA 8 (X’TAL) 7 6 MB 4 5 MB 3 2 1 10 SCL 9 (ADRESS) 115-V-K015AR 19 21 18 NC 7 NC NC NC NC NC NC NC NC TUNER+5V NC 7 TUNER_VIDEO W812 D001 F 0.1 C005 100 R006 MTZJ33B P.CON+5V 6.3V 100 YK C001_1 C002 0.1 B P.CON+8V[B] 6 W819 W820 6 FROM/TO POWER R001 P.CON+B 68K 1/2W R002 GND 68K 1/2W FROM/TO MICON 5 5 AFT R905 R904 56K 1/4W 3.2 J_AUDIO_OUT_L 220 1/4W SDA R902 SCL 56K 1/4W R901 220 1/4W FROM/TO MICON C901 2.3 BUFFER Q901 KTA1504S_Y_RTK 0 50V 1 KA J_AUDIO_OUT_R YK 50V 10 C919 39K W829 50V 1 KA R906 39K R903 BUFFER Q902 0 KTA1504S_Y_RTK 4 330 C902 2.3 R912 3.2 W830 4 FROM/TO SOUND Demod SAP RMS Det Spectral Det Noise 2.4 11 0.4 12 2.3 3.4 2 10V100 YK 2.4 10 0.1 B 9 C916 8 R913 0.1 B C917 Filter SAP C918 5.1 Filter Noise 3 Det SAP Expand Spectral C914 0.4 Filter Stereo 13 VCA Input Filter Spectral C912 C905 50V 4.7 KA 220K C903 R907 AUDIO_IN3[L] 2.2 Vcc 14 Det Pilot 100uH 0305 3.7 Filter Wide Band 50V0.33 KA C904 AUDIO_IN3[R] 2.2 7 C910 2.3 dbx De-Emph 6 0.022 B 2.3 5 50V 10 YK 0 AUDIO_IN1/2[L] 4 50V 4.7 KA AUDIO_IN1/2[R] 3 2 L-R Demod L+R Demod fH.2fH Trap Filter 2.3 1 Cancel Pilot L-R Filter L+R Filter RMS Det Wide Band 15 St.PLL 0.022 B Switch De-Emph (L-R)/SAP 75us Filter Cancel SAPout Offset Expand Cancel Wide Band Offset 16 2.6 0.1 B ZAP IIC Decoder 3.6 50V 3.3 KA GND DAC 3.7 C915 NC 0 5.0 5.0 0 20 19 18 17 Matrix J_AUDIO_OUT_R 2 21 OUT SW AGC 2.3 C908 J_AUDIO_OUT_L 22 2.3 C907 FROM/TO AV 23 2.3 50V 4.7 KA SOUND DECORDER IC IC902 AN5829S 24 2.3 0.1 B C911 3 0.047 B C913 SW_AUDIO_R 10M1/4W L901 SW_AUDIO_L PCB010 TMC559 1 NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. A G-11 B 1 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY C D E ARE PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES F G H G-12 A B C D E F G AV SCHEMATIC DIAGRAM H1 28 2 V_IN[YUV] E FROM/TO CHROMA 8 YUV_IN(REAR) J704 MSP-213V1-652_PBSN (MAIN PCB) 75 H1 5 E VIDEO_IN2 R736 MTZJ12B 75 D703 MTZJ12B R730 D702 MTZJ12B 75 VIDEO_OUT D701 R725 29 4 Y_IN[YUV] H2 3 U_IN[YUV] 1 8 A/V_OUT(REAR) J708 MSP-213V2-432_PBSN VIDEO_IN1 C710 270 R709 R705 3.3K 0 MUTE Q711 KTC3875S_Y_RTK R721 68 1.2 R711 1K 0 2.2K BUFFER Q709 KTA1504S_Y_RTK E 1 E C728 16V 470 YK 0 MUTE Q712 KTC3875S_Y_RTK 1.2 R710 0 1K 1/4W 5 1K 2 16V 10 KA 7 3 1K 6 R704 5.2 4.6 R706 16V 47 KANP C707 16V 10 KA R708 R703 3.3K C708 22 1/4W 16V100 YK R702 C711 4 VIDEO_IN3 H1 NC H1 H2 7 H 0 6 6 E 2 R728 1K E 4 E 1 E 1 5 6 MTZJ6.2B 4.5 2 Vin2 75 D709 Vcc 0 0.1 B R735 GND 6 V.OUT 5 Vin1 4 1 12.7 SW1 2 3.7 3 S_IN 4.5 4 C734 AUDIO SW(L) IC IC702 MM1501XNRE 0 0.0056 B 3 4 R739 FROM/TO MICON AUDIO_SW 0.0056 B C736 KA 75 22 4 EXT_MUTE C738 S-JACK J702 YKF51-5503 C733 16V 5 4.5 1K 6 Vin2 R726 1K B MTZJ12B 12.7 1/4W C705 AUDIO_IN3[R] Vcc 1 75 D704 22 5 R701 16V10 KA 0 C722 R729 AUDIO_IN3[L] KA GND R733 B 0.1 F AUDIO_IN1/2[L] 16V10 16V 220 YK C706 C701 V.OUT 4 3.7 2 C702 AUDIO_IN1/2[R] 3 1 2 C725 4.5 5 3 Vin1 H1 NC H1 H2 SW1 6 0 1 AUDIO SW(R) IC IC701 MM1501XNRE J_AUDIO_OUT_L 0.0056 B 0.0056 B C735 C737 MTZJ12B 75 D705 R727 LINE1(REAR) J701 MSP-213V2-432_PBSN FROM/TO TUNER/STEREO J_AUDIO_OUT_R 5 1K 6 1 B 5 1 R734 C724 3 1 B H1 NC H1 H2 C727 4 LINE2(REAR) J703 MSP-213V2-432_PBSN 3 3 FRONT-VIDEO J705 HTJ-032-03AY C742 E 1 E 1 PCB010 TMC559 NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. A NC 3 LINE3_A_IN_R GND G-13 2 3 1K NC 1 B P.CON+12V 2 R746 H C720 FRONT-AUDIO.R J707 HTJ-032-03AR 0.0056 B 2 FROM/TO POWER 2 H LINE3_A_IN_L 0.0056 B 1K FRONT-AUDIO.L J706 HTJ-032-03AW MTZJ12B R745 1 B C741 C719 75 D706 R724 S_VIDEO_IN[C] 1 E H 2 S_VIDEO_IN[Y] 1 NC 3 FROM/TO COMB FILTER B 1 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE C D E F G H G-14 A B C D E F G H 8 8 COMB/FILTER SCHEMATIC DIAGRAM (MAIN PCB) 7 7 L1511 2.0 6 C1531 BUFFER Q1508 KTC3875S_Y_RTK 0.01 B C1528 9.0 2.5 16V 100 YK 15uH 0305 6 C1535 16V 10 R1505 KA 470 FROM/TO AV S_VIDEO_IN[C] 6.8K 270 R1503 15uH 0305 R1530 L1505 S_VIDEO_IN[Y] 1.0 4.5 COMB FILTER IC IC1501 LA76600M-TLM 6 VIDEO SW(C) IC IC1503 MM1501XNRE 0 Vin1 SW1 Vin2 Vcc 4.4 7.9 C_V_OUT_SW L1501 P.CON+8V[A] AVCC YIN1 15 0 L1508 L1510 47K FSC_OUT L1512 R1522 22uH 1K C1533 22P CH R1520 1.6 1.2K R1518 27K C1530 16V 47 YK VIDEO_OUT 2.2 24K 2 5.0 R1519 R1516 BUFFER Q1507 KTC3875S_Y_RTK 1K 0.01 B C1526 6.3V 100 YK C1525 6.3V 100 YK 0.1 B 3 100 47K GND 0305 R1523 R1510 GND 3.9K 0 0 5.0 2.4 BUFFER Q1504 KTC3875S_Y_RTK 2.0 R1508 PHASE DET FSC_IN 11 0.9 0.1 B C1515 C1520 13 RD 12 SAND CASTLE 82K C1516 2.7K R1504 C1518 0.1 B 9.5 C1512 8.2K 50V 1 KA R1509 100uH 15uH 0305 P.CON+5V R1529 C1521 0.1 B 0.1 B 14 R1528 3.6 AFC 100uH 0305 C1514 2.9 DVCC 0.1 F GND C1532 GND 4 FROM/TO CHROMA 16V100 YK V.OUT 2 GND 3 5 18 17 4.5 10 4 6 8 Vcc C1523 YOUT 0.1 B C1507 2.1 9 Vin2 16 YIN2 C1506 4.0 0.1 B 7.9 V.OUT Y/C_SW 3.4 4.9 5 0.1 B OUTSEL 0 7 0.1 B C1503 6.3V 100 YK 220uH 0305 INSEL 4.9 L1503 C1502 220uH 0305 3 C1508 L1502 6.3V 100 YK C1501 1 B 0 0 4.2 3 C1505 COUT 4.9 2 100 R1502 0.1 B CIN 4.4 5 FROM/TO MICON Y_V_OUT_SW 2.4 2.6 1 C1504 4.5 0 GND 4 4 SW1 5 0 Vin1 4 4.5 6 B 1K R1507 3.3K R1506 0.1 1 VIDEO SW(Y) IC IC1502 MM1501XNRE C1519 2 BUFFER Q1503 KTC3875S_Y_RTK 3 0.1 B 470 1 W848 1.0 C1517 C1510 5.0 C1513 100P CH 5 6.3V 100 YK C1509 0.01 B R1512 FROM/TO POWER 2 GND FROM/TO SOUND W804 GND PCB010 TMC559 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE 1 A G-15 B C D NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. E F 1 G H G-16 A B C D E F CRT/SVM SCHEMATIC DIAGRAM G H (CRT PCB) 8 R804 L802 1SS133 FROM POWER CP851B (CP851A) A2001WV2-4P C862_1 16V 47 YK R879 2.7 1/2W R872 10ELS2N D858 D857 B851 B852 10ELS2N NC 16V 47 YK C864 160V 10 YK R880 2.7 1/2W HS851 763WSA0018 C863_1 W811 R878 R871 1.5K 1/4W FROM/TO VM CP852 (CP852B) A2001WV2-3P 1 VM1 54.5 68 1/2W 0 W5RH3.5X5X1.0 W5RH3.5X5X1.0 R873 68K 1/4W 68K1/4W R874 2.0 4 1.0 2.0 R875 0 SWTCHING 82 Q857 1/4W KTA1266 1.8 1.2K 1/4W 0 SWTCHING Q859 2SC4793 R881 150 2W NC 2 VM2 3 3 SCREEN R853 100 1/4W R876 C861 500V0.0047 B R869 1SS133 AMP Q853 5.7 2SC752(G)(TM)_Y C865 500V150P B 1 FOCUS GND CP804 005P-2100 GND 1 1 NC 2 GND NC 180V 3 2 NC GND 4 3 NC HEATER 5 CP801B (CP801A) A2001WV2-5P CP803 (CD803) A2361WV2-3P 100P CH R858 0.001 B D852 33K 1/4W W805 3.9K 1/4W 108.0 12K 1/4W D856 33K 1/4W C821_1 FROM DEFLECTION R861 W5RH3.5X5X1.0 54.5 1SS133 R854 3 D853 R856 0.1 C857 500V0.0047 B 100P CH R864 R819 330 1/4W 2.0 R863 C860 82 1/4W C859 220 680P CH 1/4W R822 2.2K 1/4W 2.5 AMP Q852 KTC3198 1SS133 C806 R811 10.3 R868 100P CH D809 1.9 BLUE AMP Q812 KTC3199_Y 7.3 5.7 B853 SWITCHING Q858 2SA1837 110.0 1.8 R867 3.1 11.8 2KV 0.0022 B BUFFER Q854 KTC3198 SWTCHING Q856 KTC3198 10 1/2W C858 W809 11.8 2.5 C808 7.3 1SS133 4 SWITCHING 2.5 Q855 KTC3198 D854 7.8 R830 2.7K 1/4W 5 11.8 6.0 R866 D803 39 119.7 YK W802 220 1/4W BLUE AMP Q803 KTC4217 250V 1 R821 3301/4W R809 100 1/4W R815 C809 R859 L804 TP806 W804 150uH 15K 2W 220 1/4W 390P CH R808 5 F 1SS133 1 0 6.2 119.0 R877 10 11 68 1/2W 4 0 1.5K 1/4W 1SS133 9 1.2K 1/4W R870 D855 8 5 1SS133 R820 C805 R812 C854 7 1SS133 6 0 0 160V10 YK 582.0 121.0 117.0 GREEN AMP Q811 KTC3199_Y C853 J801 CVT3275-5101 D808 2.4 2.2K 1/4W W810 2.2K 1/4W 7.3 W806 16V47 YK 2.7K 1/4W 7.3 3.0 P.CON+12V 6 1SS133 W807 1 NC R829 123.9 D802 7.8 NC GND 39K 1/4W R814 220 1/4W 3 2 270 1/2W R865 GREEN AMP Q802 KTC4217 38 R855 P.CON+B C852 15K 2W 150uH 6 R806 TP805 L803 4 56K 1/4W 2.2K 1/4W R862 VM COIL 3.9K 1/4W 7 33 1/4W CLAMP_OFF 2.7K 1/4W B.OUT 6 R860 5 2.4 D807 R810 7 560P CH G.OUT SVM BLOCK RED AMP Q810 KTC3199_Y 16V 47 YK R.OUT 4 W820 3.0 R817 330 1/4W 3 7.3 W808 C855 GND(SIGNAL) 7.3 1SS133 220 470P CH 1/4W 2 C813 CP802B (CP802A) A2001WV2-7P 1 P.CON+8V 7.8 D801 R818 C804 7 220 1/4W 1K 1/4W 1SS133 0.01 B 1SS133 R828 2.7K 1/4W R857 1SS133 FROM CHROMA R813 123.5 470 1/2W D806 37 PCB110 TCA391 22K 1/4W C856 D805 0.0022 M D804 RED AMP Q801 KTC4217 CRT BLOCK 150uH TP804 15K 2W 8 (VM COIL PCB) PCB060 TEAA93 FROM/TO CRT/SVM CP852B (CP852) B2013H02-3P 2 NC TO VM COIL CD852_1 CU232001 2 1 1 1 2 2 2 3 3 3 S851 S852 1 1 NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. A G-17 B THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE ARE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES DESCRIBED IN PARTS LIST ONLY C D PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE E F G H G-18 WAVEFORMS MICON SOUND 100µs 5ms 1.0V 5.0V 1 5µs 1ms 50mV 17 22 1ms 200mV 5ms 10V 1.0V 2 18 50µs 20µs 1.0V 50V 3 50µs 23 1ms 100mV 24 19 20µs 2.0V 1.0V 4 1ms 100mV 25 20 DEFRECTION 5ms 200mV 16 20µs 200V 1ms 5.0V 21 26 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram. H-1 WAVEFORMS 1ms 20µs 5.0V 50V 27 39 AV 20µs 200mV 28 20µs 200mV 29 20µs 50V 37 20µs 50V 38 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram. H-2 MECHANICAL EXPLODED VIEW 202 113 202 202 202 202 202 125 112 111 204 204 201 118 118 122 202 201 206 PCB110 (CRT PCB ASS'Y) PCB060 (VM COIL PCB ASS'Y) 116 201 115 112 121 206 205 205 201 206 120 119 202 117 202 203 114 203 119 120 207 124 123 PCB010 (MAIN PCB ASS'Y) 207 110 120 119 204 109 108 107 104 106 108 117 202 203 110 103 203 105 101 102 I-1 202 119 120 MECHANICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description 101 102 103 104 105 106 107 108 109 AD302004 AD302005 AD302006 AD302007 AD302008 AD302009 AD302010 AD302011 AE000002 A3M701Z720 701WPJ1175 711WPA0184 713WPA0263 7235490036 735WPA0728 735WPA0732 735WPB0243 735WPJ0235 CABINET,FRONT ASSY CABINET,FRONT PLATE,FRONT GLASS,LED BADGE,BRAND STOPPER,BUTTON STOPPER,BUTTON2 BUTTON,FRAME BUTTON,POWER 110 111 112 113 114 115 116 117 118 119 AE000003 AE000004 AD300520 AD302013 AD300132 AD301113 BZ710258 AD302015 BZ710259 AD300518 800WQ00045 7250000581 800WQ00068 7225490106 7230006818 723000B873 741WUA0001 761WPA0220 762WPA0011 801WR00001 FELT SHEET SHEET,PVC FELT SHEET SHEET,RATING SHEET,CAUTION FILM,DECORATION SPRING,EARTH HOLDER,SPEAKER HOLDER,CRT WIRE DAMPER,SPEAKER 120 121 122 123 124 125 AD300519 BZ710260 AE000005 AE000006 AE000007 AE000008 82A40B0104 899HV3T000 702WPA0988 7220001119 7220001107 7260000345 FLAT WASHER HOLDER,ANODE WIRE CABINET,BACK SHEET,CSA WARNING SHEET,HWC SHEET,SERVICEMAN 201 202 203 204 205 206 207 AD302054 BZ710035 BZ710034 BZ710031 BZ710018 BZ710239 BZ710019 8141J50C54 8117540A64 8117140A24 8110630A04 8107630804 8109I30A04 8109630802 SCREW,TAP TITE(P) GW22 SCREW,TAPPING(B0) TRUSS SCREW,TAPPING(B0) PAN SCREW,TAP TITE(P) BRAZIER SCREW,TAP TITE(S) BRAZIER SCREW,TAP TITE(B) WH7 SCREW,TAP TITE(B) BRAZIER ----------------------- AE000009 AE000010 AD302017 AD302018 AD302019 AE000011 AD302020 AD300022 AD300023 AD302021 AD301213 7230007664 791WHA0085 792WHA0432 792WHA0433 793WCD1469 7230007398 A3M701Z975 J3I70417 J3I70436 J3M70101A JA4UD300 SHEET,BAR CODE LAMIFILM,BAG PACKAGE,TOP PACKAGE,BOTTOM GIFT BOX SECURITY TAG (FOR CANADA ONLY) INSTRUCTION BOOK KIT REGISTRATION CARD ESP CARD INSTRUCTION BOOK POLYBAG,INSTRUCTION(RED CAUTION) J1-1 5x35 4x16 4x12 3x10 3x8 3x10 3x8 ELECTRICAL REPLACEMENT PARTS LIST ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! Location No. TSB P/N Reference No. RESISTORS R151 R402 R410 R416 R420 R426 R434 R436 R438 R439 R441 R452 R500 R501 R502 R506 R517 R520 R527 R538 R541 R542 R602 R649 R655 R657 R804 R806 R808 R855 R881 BZ210235 BZ210021 AD301344 AD301593 AD301345 BZ210030 AD301972 BZ210023 BZ210104 BZ210003 AD300037 BZ210217 BZ210080 AD301596 AD301016 BZ210162 AD301973 BZ210206 BZ210149 BZ210235 BZ210190 AD301017 AD301975 AD301975 BZ210235 AD301200 BZ210026 BZ210026 BZ210026 AD301976 AD301344 R00204103J R65582680J R3X18A151J R002T23R3J R002T22R7J R4X5T4472F R5X2CF5R6J R4X5T4183F R6558A2R7J R3K181102J R4X5T6153F R3X181331J R0G3K2275K R5X2AE010J R3X28A331J R002T4682J R3X28BR22J R002T2155J R3X18AR68J R00204103J R63581R22J R3X181R15J R3X28B120J R3X28B120J R00204103J R00204102J R3X18A153J R3X18A153J R3X18A153J R65582271J R3X18A151J C408 C413 C418 C420 C425 C426 C430 C501 C502 C503 C504 C505 C808 C1003 C1004 C1009 BZ110032 AD301977 BZ110136 AD301978 BZ110182 AD300061 BZ110195 BZ110053 BZ110182 BZ110182 AD301729 BZ110025 BZ110138 BZ110035 BZ110145 BZ110012 AD301108 AD301026 BZ110191 AD301026 AD301025 BZ110119 BZ110182 BZ110250 AD300925 BZ110226 BZ110053 BZ110053 BZ110053 E5EZF3102M E0ELF4102M P4J7F3394J P4N8FJ133H C03L0R713K E5EZFD220M E02LU8220M E02LF3102M C03L0R713K C03L0R713K E02LU52R2M P2122B224M P2472B224M P2122B104M P2472B104M E51CGC471M CD39E0MH3M CD39E0M13M C03L0R7E3K CD39E0M13M E62NFB221M E02LF2222M C03L0R713K E02L02102M E02LT2102M C0JBB07H3K E02LF3102M E02LF3102M E02LF3102M D001 D104 D105 D106 D107 D108 D109 D110 D116 BZ410037 BZ410006 BZ410006 BZ410020 BZ410006 BZ410006 BZ410054 BZ410006 AE000001 D97U03301B D1VT001330 D1VT001330 D97U05R11B D1VT001330 D1VT001330 0021721150 D1VT001330 D97005R61B RC R,FUSE R,METAL OXIDE RC RC R,METAL R,CEMENT R,METAL R,FUSE R'METAL R,METAL R,METAL OXIDE RC R,CEMENT R,METAL OXIDE RC R.METAL RC R,METAL OXIDE RC R,FUSE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE RC RC R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,FUSE R,METAL OXIDE Description 10K OHM 1/4W 68 OHM 1/2W 150 OHM 2W 3.3 OHM 1/2W 2.7 OHM 1/2W 4.7K OHM 1/4W 5.6 OHM 10W 18K OHM 1/4W 2.7 OHM 2W 1K OHM 1W 15K OHM 1/6W 330 OHM 1W 2.7M OHM 1/2W 1 OHM 7W 330 OHM 2W 6.8K OHM 1/4W 0.22 OHM 3W 1.5M OHM 1/2W 0.68 OHM 2W 10K OHM 1/4W 0.22 OHM 1W 0.15 OHM 1W 12 OHM 3W 12 OHM 3W 10K OHM 1/4W 1K OHM 1/4W 15K OHM 2W 15K OHM 2W 15K OHM 2W 270 OHM 1/2W 150 OHM 2W CAPACITORS ! ! ! ! ! ! ! ! ! ! C506 ! C507 ! C508 ! C513 C517 ! C519 ! C521 ! C527 C535 C550 CE CE CMPP CMPP CC CE CE CE CC CC CE CMP CMP CMP CMP CE CC CC CC CC CE CE CC CE CE CC CE CE CE 1000 UF 25V 1000 UF 35V 0.39 UF 250V PMS 0.013 UF 1.25KV 0.001 UF 2KV R 22 UF 250V 22 UF 100V 1000 UF 25V 0.001 UF 2KV R 0.001 UF 2KV R 2.2 UF 50V 0.22 UF 275V ECQUL 0.22UF 275V PHE840 0.1 UF 275V ECQUL 0.1 UF 275V PHE840 470 UF 200V 0.0022UF 250V 0.001 UF 250V 0.0015UF 2KV R 0.001 UF 250V 220 UF 160V 2200 UF 16V 0.001 UF 2KV R 1000 UF 16V 1000 UF 16V 0.0022UF 2KV B 1000 UF 25V 1000 UF 25V 1000 UF 25V DIODES DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON LED DIODE,SILICON DIODE,ZENER J2-1 MTZJ33B T-77 1SS133T-77 1SS133T-77 MTZJ5.1B T-77 1SS133T-77 1SS133T-77 SLR-342VCT32 1SS133T-77 MTZJ5.6B or or or ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N D402 D403 D404 D405 D406 D407 D410 D411 D414 D415 D501 D502 D503 D504 D505 D506 D507 D508 D509 D510 D511 D512 D513 D514 D516 D517 D520 D523 D524 D525 D528 D601 D602 D603 D604 D605 D606 D607 D608 D610 D611 D701 D702 D703 D704 D705 D706 D709 D801 D802 D803 D804 D805 D806 D807 D808 D809 D852 D853 D854 D855 D856 D857 D858 BZ410043 BZ410019 BZ410020 BZ410063 BZ410021 AD301979 BZ410019 BZ410063 BZ410043 BZ410043 BZ410062 BZ410062 BZ410062 BZ410062 AD300076 AD300731 BZ410006 BZ410064 AD300671 AD301980 AD300731 BZ410010 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 AD300671 BZ410006 AD300070 BZ410021 BZ410006 BZ410058 AD300670 AD300070 BZ410006 BZ410006 BZ410006 BZ410043 BZ410099 BZ410099 AD300070 AD300070 AD300070 AD300070 AD300070 AD300070 BZ410066 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410011 BZ410011 D2WT011E10 D97U03001B D97U05R11B D2WTAU02A0 D97U05R61B D2W0AU02A0 D97U03001B D2WTAU02A0 D2WT011E10 D2WT011E10 D2WTRM11C0 D2WTRM11C0 D2WTRM11C0 D2WTRM11C0 D28F30DF60 D2WXN49370 D1VT001330 D97U03R91B D97U01801B D2CF2016L0 D2WXN49370 D28T21DQN9 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D97U01801B D1VT001330 D97U01201B D97U05R61B D1VT001330 D97U08R21B D97U01501B D97U01201B D1VT001330 D1VT001330 D1VT001330 D2WT011E10 D2W0B290S0 D2W0B290S0 D97U01201B D97U01201B D97U01201B D97U01201B D97U01201B D97U01201B D97U06R21B D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D28TELS2N2 D28TELS2N2 DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,RECTIFIER DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SCHOTTKY DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,RECTIFER DIODE,RECTIFER IC101 IC199 IC301 IC302 ! IC401 ! IC504 AD301981 AD301982 AD300055 AD301983 BZ611025 BZ410088 I56F07090A A3M701Z015 I0QF021500 I01FF58910 I03TD80400 0002E00610 IC IC IC IC IC PHOTO COUPLER ! ! ! ! ! ! ! ! ! ! ! ! ! ! Reference No. DIODES Description 11E1-EIC MTZJ30B T-77 MTZJ5.1B T-77 AU02A-EIC MTZJ5.6B T-77 AU02A-B-EIC MTZJ30B T-77 AU02A-EIC 11E1-EIC 11E1-EIC RM11C-EIC RM11C-EIC RM11C-EIC RM11C-EIC 30DF6-FC 1N4937 1SS133T-77 MTZJ3.9B T-77 MTZJ18B T-77 FE201-6L49 1N4937 21DQ09N-TA2B1 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 MTZJ18B T-77 1SS133T-77 MTZJ12B T-77 MTZJ5.6B T-77 1SS133T-77 MTZJ8.2B T-77 MTZJ15B T-77 MTZJ12B T-77 1SS133T-77 1SS133T-77 1SS133T-77 11E1-EIC SB290S-B-EIC SB290S-B-EIC MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ6.2B T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 10ELS2N-TA1B2 10ELS2N-TA1B2 ICS J2-2 OEC7090A S-24C16AFJA-TB-01 NJM2150AM AN5891SA-E1V LA78040 LTV-817M-VB ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description ICS IC601 IC701 IC702 IC902 ! IC1001 IC1501 IC1502 IC1503 AD301984 AD301988 AD301988 AD300059 AD300056 AD301029 AD301988 AD301988 I06FC12830 I0UF015010 I0UF015010 I01FF58290 I0FSP52760 I03FE76600 I0UF015010 I0UF015010 Q101 Q103 Q402 Q405 Q502 Q503 Q504 Q505 Q507 Q508 Q509 Q512 Q514 Q601 Q602 Q603 Q604 Q605 Q606 Q607 Q610 Q611 Q613 Q614 Q709 Q711 Q712 Q801 Q802 Q803 Q810 Q811 Q812 Q852 Q853 Q854 Q855 Q856 Q857 Q858 Q859 Q901 Q902 Q1001 Q1503 Q1504 Q1507 Q1508 BZ510109 BZ510109 BZ510097 BZ510040 BZ510098 BZ510005 BZ510069 BZ510011 BZ510069 BZ510077 BZ510069 BZ510004 BZ510070 BZ510105 BZ510105 BZ510109 BZ510105 BZ510109 BZ510105 BZ510070 BZ510109 BZ510105 BZ510109 BZ510108 BZ510108 BZ510109 BZ510109 BZ510091 BZ510091 BZ510091 AD301032 AD301032 AD301032 BZ510069 AD300024 BZ510069 BZ510069 BZ510069 BZ510073 AD300029 AD300025 BZ510108 BZ510108 BZ510068 BZ510109 BZ510109 BZ510109 BZ510109 TCAA3875SY TCAA3875SY TCAT03227Y TDUU024990 T220033260 TA3T1371A0 TCATC31980 TC3T029090 TCATC31980 TAAT012714 TCATC31980 TA3T016240 TCAT032034 TCAT03209Y TCAT03209Y TCAA3875SY TCAT03209Y TCAA3875SY TCAT03209Y TCAT032034 TCAA3875SY TCAT03209Y TCAA3875SY TAAA1504SY TAAA1504SY TCAA3875SY TCAA3875SY TCA0042170 TCA0042170 TCA0042170 TCATC3199Y TCATC3199Y TCATC3199Y TCATC31980 TCUT00752Y TCATC31980 TCATC31980 TCATC31980 TAATA12660 TAU0018370 TCU0047930 TAAA1504SY TAAA1504SY TNAAJ05003 TCAA3875SY TCAA3875SY TCAA3875SY TCAA3875SY BZ310041 BZ310004 BZ310063 AD300119 BZ310066 AD301989 AD301990 AD300123 AD300123 AD300123 BZ310041 BZ310041 AD301417 02167F101J 021679472K 022100027A 029T000097 028R200024 0216A6330J 021LA6330J 021673151K 021673151K 021673151K 02167F101J 02167F101J 02167F221J IC IC IC IC IC IC IC IC M61283FP MM1501XNRE MM1501XNRE AN5829S AN5276 LA76600M-TLM MM1501XNRE MM1501XNRE TRANSISTORS ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON FET TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3227_Y-AT 2SD2499(LB0EC1) 2SK3326(2) 2SA1371(D,E)-AE KTC3198-AT(Y,GR) 2SC2909(S,T)-AA KTC3198-AT(Y,GR) KTA1271_Y-AT KTC3198-AT(Y,GR) 2SA1624-AA KTC3203_Y-AT KTC3209_Y-AT KTC3209_Y-AT KTC3875S_Y_RTK KTC3209_Y-AT KTC3875S_Y_RTK KTC3209_Y-AT KTC3203_Y-AT KTC3875S_Y_RTK KTC3209_Y-AT KTC3875S_Y_RTK KTA1504S_Y_RTK KTA1504S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK KTC4217(O,Y) KTC4217(O,Y) KTC4217(O,Y) KTC3199_Y-AT KTC3199_Y-AT KTC3199_Y-AT KTC3198-AT(Y,GR) 2SC752(G)(TM)_Y KTC3198-AT(Y,GR) KTC3198-AT(Y,GR) KTC3198-AT(Y,GR) KTA1266-AT(Y,GR) 2SA1837 2SC4793 KTA1504S_Y_RTK KTA1504S_Y_RTK KRC111SRTK KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK COILS &TRANSFORMERS L301 L401 L402 ! L501 ! L503 L601 L802 L803 L804 L901 L1501 L1502 COIL COIL COIL,LINEARITY COIL,LINE FILTER COIL,DEGAUSS COIL COIL COIL COIL COIL COIL COIL COIL J2-3 100 UH 4.7 MH ELH5L4113 1R5A123F28Y 8R200024 33 UH 33 UH 150 UH 150 UH 150 UH 100 UH 100 UH 220 UH or ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. COILS &TRANSFORMERS L1503 L1505 L1508 L1510 L1511 L1512 T401 ! T501 AD301417 AD300613 BZ310041 AD300613 AD300613 AD301608 AD301033 BZ310172 AD301034 02167F221J 02167F150J 02167F101J 02167F150J 02167F150J 0216A6220J 021LA6220J 045013003J 048140066S J701 J702 J703 J704 J705 J706 J707 J708 ! J801 ! J1001 AD301038 AD300108 AD301038 AD301037 AD300110 AD300111 AD300112 AD301038 BZ614115 BZ614361 060J431019 063Q700002 060J431019 060J411024 060G401047 060G401046 060G401039 060J431019 066C130017 060J131015 BZ612010 BZ612001 BZ612010 BZ612001 BZ612010 BZ612001 BZ612010 BZ612001 BZ612010 BZ612001 0504101T34 0504201T31 0504101T34 0504201T31 0504101T34 0504201T31 0504101T34 0504201T31 0504101T34 0504201T31 VR401 VR502 BZ210108 BZ210101 V116313BTC V1163H4BTC PCB010 PCB060 PCB110 AD301991 AD301992 AD301993 A3M701Z010 A3M701Z060 A3M701Z110 B401 B402 B403 B405 B501 B504 B851 B852 B853 BT001 BT002 CD501 CD801 CD802 CD803 CD851 CD852 CP101 CP401 CP501 CP502 CP507 BZ310129 BZ310129 BZ310122 BZ310129 BZ310045 BZ310121 BZ310121 BZ310121 BZ310121 AE000012 AE000012 AD300746 AD301042 AD301994 AD300094 AD301995 AD301043 BZ614102 AD300095 BZ614176 AD300687 BZ614444 BZ614016 BZ614444 BZ614016 AD301996 AD300096 BZ614058 BZ614350 AD300093 AD301045 BZ614276 024HT03564 024HT03564 024HT03563 024HT03564 024AT03481 024HT03553 024HT03553 024HT03553 024HT03553 1412004008 1412004008 120R615901 06CU253401 06CU274201 06CP83035A 06CU244201 06CU232001 0694270139 069X460029 069S320419 069S420110 069D01001A 069W01001A 069D01001A 069W01001A 069S330010 069W330018 069W010010 069S230629 06CU14411A 069S140419 067U005049 Description COIL COIL COIL COIL COIL COIL COIL LAP02TA220J TRANS,HORIZONTAL DRIVE TRANSFORMER,SWITCHING 220 UH 15 UH 100 UH 15 UH 15 UH 22 UH 22 UH ETH14Y47AY 8140066S or JACKS RCA JACK JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK SOCKET,CATHODE RAY TUBE HEADPHONE JACK MSP-213V2-432 PBSN YKF51-5503 MSP-213V2-432 PBSN MSP-213V1-652 PBSN HTJ-032-03AY HTJ-032-03AW HTJ-032-03AR MSP-213V2-432 PBSN CVT3275-5101 MSJ-2000 SWITCHES SW101 SW102 SW103 SW104 SW105 SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT EVQ21505R SKHVBED010 EVQ21505R SKHVBED010 EVQ21505R SKHVBED010 EVQ21505R SKHVBED010 EVQ21505R SKHVBED010 or or or or or VARIABLE RESISTORS VOLUME,SEMI FIXED VOLUME,SEMI FIXED EVNCYAA03B13 EVNCYAA03BE4 P.C.BOARD ASSEMBLIES PCB ASS'Y PCB ASS'Y PCB ASS'Y TMC559A TEAA93B TCA391B MISCELLANEOUS ! ! ! ! CP508 CP803 CP804 CP852 CD1001 CP1001 CP801A CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS BATTERY,MANGAN BATTERY,MANGAN CORD,AC BUSH CORD,CONNECTOR CORD,CONNECTOR CORD,CONNECTOR CORD,CONNECTOR CORD,CONNECTOR CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CORD,CONNECTOR CONNECTOR PCB SIDE WIRE HOLDER J2-4 W4BRH3.5X6X1.0 W4BRH3.5X6X1.0 W4BRH3.5X6X1.0X2 W4BRH3.5X6X1.0 BL02RN1-R62T2 W5RH3.5X5X1.0 W5RH3.5X5X1.0 W5RH3.5X5X1.0 W5RH3.5X5X1.0 R03(AB)E_2P_G R03(AB)E_2P_G 0R615901 CU253401 CU274201 CP83035A CU244201 CU232001 173979-7 B06B-DVS A3963WV2-3PD A1561WV2-2P 003P-2100 003P-2100 003P-2100 003P-2100 A2361WV2-3P TS-80P-03-V1 005P-2100 A2001WV2-3P CU14411A A2502WV2-4P B2013H02-5P or or or ELECTRICAL REPLACEMENT PARTS LIST ! ! ! ! ! ! ! ! Location No. TSB P/N Reference No. MISCELLANEOUS CP801B CP802A CP802B CP851A CP851B CP852B EL001 EL002 F501 FB401 FH501 FH502 OS101 RY501 SP1001 SP1002 TH501 TM101 TU001 V801 X101 X602 AD300752 AD301997 BZ614485 BZ614334 AD301998 BZ614349 BZ614044 BZ614043 AD301046 AD301999 BZ614005 BZ614005 AD301048 AD300114 AD301050 AD301050 AD302000 AD302001 AD301800 AD301053 AD302002 AD302003 069S250629 067U007029 069S270629 067U004029 069S240629 067U003029 124120301A 124116281A 081PC6R305 043220057F 06710T0006 06710T0006 0773071001 0560V20115 070C457003 070C457003 D8EE0B1400 076R0GF010 0163300001 098W210437 100CT8R005 100CT3R505 RC................... CARBON RESISTOR CC................... CE................... CP................... CPP.................. CPL.................. CMP................... CMPL................ CMPP................ CERAMIC CAPACITOR ALUMI ELECTROLYTIC CAPACITOR POLYESTER CAPACITOR POLYPROPYLENE CAPACITOR PLASTIC CAPACITOR METAL POLYESTER CAPACITOR METAL PLASTIC CAPACITOR METAL POLYPROPYLENE CAPACITOR Description CONNECTOR PCB SIDE WIRE HOLDER CONNECTOR PCB SIDE WIRE HOLDER CONNECTOR PCB SIDE WIRE HOLDER EYE LET EYE LET FUSE TRANSFORMER,FLYBACK HOLDER,FUSE HOLDER,FUSE REMOTE RECEIVER RELAY SPEAKER SPEAKER DEGAUSS ELEMENT TRANSMITTER RF UNIT CRT W/DY CRYSTAL CRYSTAL RESISTOR CAPACITORS J2-5 A2001WV2-5P B2013H02-7P A2001WV2-7P B2013H02-4P A2001WV2-4P B2013H02-3P XRY20X30BD XRY16X28BD 51MS063L FJN20A002 EYF-52BC EYF-52BC RPM7138-H5 ALKS321 SG05K07BRA SG05K07BRA B59203-S1060-B14 R25-1911 115-V-K015AR A51LVV896X07(O) HC-49/U-S HC-49/C TOSHIBA CORPORATION 1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN