Download Service Manual of Sony DSC-S730 Digital Camera

DSC-S730
SERVICE MANUAL
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Tourist Model
Ver. 1.0 2007.11
Revision History
Internal memory
ON BOARD
Link
SPECIFICATIONS
DISASSEMBLY
SERVICE NOTE
BLOCK DIAGRAM
The components identified by
mark
or dotted line with
mark are critical for safety.
Replace only with part number specified.
REPAIR PARTS LIST
Les composants identifiés par une
marque
sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
In case of the lens block assy, main board, or main frame assembly failure,
contact your local Sony Service Headquarter for the measures.
DIGITAL STILL CAMERA
DSC-S730
9-852-239-11
Sony EMCS Co.
2007K0200-1
© 2007.11
Published by Kohda TEC
SPECIFICATIONS
[System]
[LCD screen]
Image device: 7.20 mm (1/2.5 type) color CCD,
Primary color filter
Total pixel number of camera:
Approx. 7 410 000 pixels
Effective pixel number of camera:
Approx. 7 201 000 pixels
Lens: 3× zoom lens f = 5.8 – 17.4 mm (35 –
105 mm when converted to a 35 mm still
camera) F2.8 (W) – 4.8 (T)
Exposure control: Automatic exposure, Scene
Selection (7 modes)
White balance: Automatic, Daylight, Cloudy,
Fluorescent, Incandescent, Flash
File format (DCF compliant):
Still images: Exif Ver. 2.21 JPEG compliant,
DPOF compatible
Movies: AVI (Motion JPEG)
Recording media: Internal Memory (approx.
22 MB), "Memory Stick Duo"
Flash: Flash range (ISO sensitivity
(Recommended Exposure Index) set to Auto):
approx. 0.5 to 3.5 m (1 feet 7 3/4 inches to 11
feet 5 7/8 inches) (W)/approx. 0.5 to 2.0 m (1
feet 7 3/4 inches to 6 feet 6 3/4 inches) (T)
LCD panel: 6.0 cm (2.4 type) TFT drive
Total number of dots: 112 320 (480×234) dots
[Power, general]
Power: LR6 (size AA) Alkaline batteries (2), 3 V
HR15/51:HR6 (size AA) Nickel-Metal
Hydride batteries (2) (not supplied), 2.4 V
ZR6 (size AA) Oxy Nickel Primary Battery
(2) (not supplied), 3 V
AC-LS5K AC Adaptor (not supplied), 4.2 V
Power consumption (during shooting): 1.2 W
Operating temperature: 0 to 40 C (32 to 104 F)
Storage temperature: –20 to +60 C (–4 to +140 F)
Dimensions: 91.4×61.0×29.1 mm (3 5/8×2 1/2×
1 3/16 inches) (W/H/D, excluding
protrusions)
Mass: Approx. 189 g (6.7 oz) (including two
batteries and strap, etc.)
Microphone: Monaural
Buzzer
Exif Print: Compatible
PRINT Image Matching III: Compatible
PictBridge: Compatible
[Input and Output connectors]
(USB) A/V OUT terminal:
Video, Audio (Monaural), USB
communication
USB communication:
Hi-Speed USB (USB 2.0 compliant)
DSC-S730
Design and specifications are subject to change
without notice.
—2—
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK OR DOTTED LINE WITH
MARK
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1.
2.
3.
4.
5.
6.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
Check the B+ voltage to see it is at the values specified.
FLEXIBLE Circuit Board Repairing
Keep the temperature of the soldering iron around 270 C
during repairing.
Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
Be careful not to apply force on the conductor when soldering
or unsoldering.
DSC-S730
Unleaded solder
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
Unleaded solder melts at a temperature about 40 C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
—3—
TABLE OF CONTENTS
Section
1.
Title
Page
SERVICE NOTE
1-1. Process After Fixing Flash Error ····································· 1-1
1-2. Method for Copying or Erasing the Data in Internal
Memory ··········································································· 1-1
2.
DISASSEMBLY
2-1. Disassembly ····································································· 2-1
3.
BLOCK DIAGRAM
3-1. Overall Block Diagram ··················································· 3-1
4.
REPAIR PARTS LIST
4-1. Exploded Views ······························································· 4-1
4-1-1. Overall Section ······························································ 4-1
4-1-2. Main Frame Block ························································· 4-2
4-2. Accessories ······································································ 4-3
DSC-S730
—4—
1. SERVICE NOTE
1-1. PROCESS AFTER FIXING FLASH ERROR
Method for Initializing the Flash Error
Initialize
Initializes the setting to the default setting.
Even if you execute this function, the images stored in the internal memory are retained.
1 Select [OK] with v on the control button, then press z.
The message "Initialize all settings Ready?" appears.
2 Select [OK] with v, then press z.
The settings are reset to the default setting.
To cancel initializing
Select [Cancel] in step 1 or 2, then press z.
Be sure not to power off the camera while initializing.
1-2. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)
Note: When replacing the camera, erase the data in internal memory of the board before replacement.
Method for Copying the Data in Internal Memory
Copy
Copies all images in the internal memory to a "Memory Stick Duo".
1 Insert a "Memory Stick Duo" having sufficient free capacity.
2 Select [OK] with v on the control button, then press z.
The message "All data in internal memory will be copied Ready?" appears.
3 Select [OK] with v, then press z.
Copying starts.
To cancel copying
Select [Cancel] in step 2 or 3, then press z.
Use batteries with enough power remaining. If you attempt to copy image files using batteries with little
remaining charge, the batteries may run out, causing copying to fail or possibly corrupting the data.
You cannot select images to copy.
The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the "Memory Stick Duo" after copying, then format the internal memory
([Format] in [Internal Memory Tool]).
A new folder is created on the "Memory Stick Duo" and all the data will be copied to it. You cannot
choose a specific folder and copy images to it.
The
(Print order) marks on the images are not copied.
Method for Formatting the Internal Memory
This item does not appear when a "Memory Stick Duo" is inserted in the camera.
Format
Formats the internal memory.
Note that formatting permanently erases all data in the internal memory, including even protected images.
1 Select [OK] with v on the control button, then press z.
The message "All data in internal memory will be erased Ready?" appears.
2 Select [OK] with v, then press z.
The format is complete.
To cancel formatting
Select [Cancel] in step 1 or 2, then press z.
DSC-S730
1-1
2. DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1. DISASSEMBLY
5
3
2
4
2
1
3
1
4
1 Open the BT LID
1 SCREW TP 1.4 X 3.5
2 SCREW M 1.7 X 2.7
2 SCREW TP 1.4 X 4
3 SCREW TP 1.7 X 4
3 LCD
4 SCREW TP 1.7 X 3.5
4 LCD PLATE
5 CABINET (REAR) ASSY
2
plate
(To 2-2 Page)
3
1
3
1
Note :
When CABINET(FRONT) ASSY is
removed, the plate will bends if
CABINET(FRONT) ASSY is inclined
too much.
Please remove CABINET (FRONT)
ASSY as in parallel as possible.
2
1 BT LID SHAFT
2 BT LID
3 BT LID SPRING
DSC-S730
2-1
1 SCREW TP 1.4 X 3
2 SCREW TP 1.4 X 2.5
3 CABINET (FRONT) ASSY
1
1
2
3
2
3
3
2
(From 2-1 Page)
1
4
Caution
1 SCREW TP 1.4 X 2.5
Shorting jig
(1kΩ / 1W)
Note :
After discharged, a transparent
seal is put again.
Do not lose the transparent seal
removed when discharged.
1 STRAP SHAFT
1 SCREW TP 1.7 X 3.5
2 SCREW TP 1.7 X 3.5
2 SCREW TP 1.4 X 3
2 SCREW TP 1.7 X 6.5
3 MAIN MOUNT
3 RL BLOCK
3 ST BLOCK ASSY
4 SUPPORT (JACK)
1
2
4
3
5
1 JACK LID
2 SCREW TP 1.4 X 3
3 LENS BLOCK ASSY
4 LID
5 MAIN FRAME
DSC-S730
2-2
3. BLOCK DIAGRAM
3-1. OVERALL BLOCK DIAGRAM
MAIN BOARD
LC D
LCD_BACKLIGHT
1
STROBE & TOP BOARD
RED
LC D_E N
LC D_MC LK
LC D_V D
LC D_HD
LC D_S C LK
LC D_S DA T A
LC D [0 ..7 ]
MLC D_O N
BL
LC D_E N
LC D_MC LK
LC D_VD
LC D_HD
LC D_SC LK
LC D_SDATA
LC D[0..7]
MLC D_ON
BL
P X C LK
HD
VD
C DS _E N
S C LK
S DA T A
A F E RS T
T G _E N
V S UB _C on1
V S UB _C on2
C C D_O N
T G _O N
C DS _O N
C C D[0..11 ]
PXC LK
HD
VD
C DS_E N
SC LK
SDATA
AF E RST
TG_E N
VSUB_C on1
VSUB_C on2
C C D_ON
TG_ON
C DS_ON
C C D[0..11]
LC D_E N
LC D_MC LK
LC D_VD
LC D_HD
LC D_SC LK
LC D_SDATA
LC D[0..7]
MLC D_ON
BL
DG ND
DGND
2
LENS BLOCK
C DS
DS P
+5V M
+3.1V D
+5VM
+3.1VD
AUO LCD
2.36
INCH
PANEL
PXC LK
HD
VD
C DS_E N
SC LK
SDATA
AF E RST
TG_E N
VSUB_C on1
VSUB_C on2
C C D_ON
TG_ON
C DS_ON
C C D[0..11]
+3.3V
+3.3V
-7.5V
-7.5V
DG ND
DGND
C DS
DGND
DDR
TOP
RAMD[0..15]
RAMA[0..14]
RAMLDM
RAMW E _N
RAMC AS
RAMRAS
RAMC S_N
RAMLDQS
RAMUDQS
RAMUDM
RAMC LK_N
RAMC LK
RAMC LK_E N
RAMRE F
POWER LED
+2.5V D
2
GREEN
1
+2.5VD
DG ND
2
P1,P2
F LA S H_V P
FLASH
CHARGER
1
Q5
1
2
DGND
FLASH TUBE
S NC
3
MS _O N
R/B
MS _INS #
C LE
WE
WP
A LE
CE 0
RE
MS _C LK
MD [0 ..7]
F A 23
F A 20
F A 22
F A 21
MS_ON
R/B
MS_INS#
C LE
WE
WP
ALE
CE0
RE
MS_C LK
MD[0..7]
F A23
F A20
F A22
F A21
RAMD[0..15]
RAMA[0..14]
RAMLDM
RAMW E _N
RAMC AS
RAMRAS
RAMC S_N
RAMLDQS
RAMUDQS
RAMUDM
RAMC LK_N
RAMC LK
RAMC LK_E N
RAMRE F
DDR
1
ME MO RY
3
BE E PE R
BE E PE R
2
F LA S H_RDY
F LA S H_C HG _L
S T RO B E _T RG
S T RO B E _C HG
A F _LE D
S T RO B E _P W R
F LASH_RDY
F LASH_C HG_L
STROBE _TRG
STROBE _C HG
AF _LE D
STROBE _PW R
FOCUS MOTOR
LE NS _E N
LE NS _S C LK
LE NS _S DA T A
Z O O M_P I
Z O O M_P R
F O C US _P I
+5V M
DG ND
LE NS_E N
LE NS_SC LK
LE NS_SDATA
ZOOM_PI
ZOOM_PR
F OC US_PI
F LA S H
MODE DIAL
FUNCTION KEY
12MHZ
1
+3.3V
+3.1V D
+5V M
+1.8V D
+3.3V
+3.1V D
+3.1VD
+3.3V S
+5VM
+13.4V
+1.8V D
+3.3V
+13.4V
C C D_ON
+1.8VD
DGND
C C D_O N
+2.5V D
DG ND
DG ND
S W _T E LE
SW _TE LE
5
VP
+2.5VD
S W _W IDE
SW _W IDE
PW R_C TRL
2
1
-7.5V
+2.5V D
C C D_ON1
VP
+1.8VD
+3.1VD
+3.3VS
+3.3V
+2.5VD
DGND
32.768K Hz
4
C C D_O N1
P W R_C T RL
1
PW R_C TRL
MIC _N
VP
-7.5V
MIC
C C D_ON1
VP
JA C K
S W _P LA Y B A C K
SW _PLAYBAC K
6
2
PO WE R
4
SW
PC
UG ND
UGND
5
DGND
SW _KE Y_ADC 1
SW _KE Y_ADC
DG ND
DGND
1
S W _K E Y _A DC 1
S W _K E Y _A DC
SW _KE Y_ADC 1
SW _KE Y_ADC
+3.1V D
+3.1VD
6
STA_LE D
D+
DUSB_DE T
A/V_DE T
VIDE O_OUT
LINE _OUT
BE E PE R
3
S T A _LE D
D+
DUS B _DE T
A V _DE T
V IDE O _O UT
LINE _O UT
BE E PE R
D+
DUSB_DE T
AV_DE T
VIDE O_OUT
LINE _OUT
BE E PE R
5
DG ND
SHUTTER MOTOR
JA C K
2
GREEN
STA_LE D
+3.1VD
IRIS MOTOR
LE NS
SW
+3.1V D
LE NS_E N
LE NS_SC LK
LE NS_SDATA
ZOOM_PI
ZOOM_PR
F OC US_PI
+5VM
DGND
P W R_O N
P W RK E Y
B A T _LO A D
PW R_ON
PW RKE Y
BAT_LOAD
MS LED
1
FOCUS SENSOR
2
DGND
F LASH_RDY
F LASH_C HG_L
STROBE _TRG
STROBE _C HG
AF _LE D
STROBE _PW R
4
+3.1VD
ZOOM MOTOR
2
+5VM
ZOOM SENSOR
+3.1VD
LE NS_PS
SHUTTE R_M1
SHUTTE R_M0
IN1
IN2
IN3
IN4
6
DG ND
F LASH_VP
+3.1V D
LE NS _P S
S HUT T E R_M1
S HUT T E R_M0
IN1
IN2
IN3
IN4
LE NS_PS
SHUTTE R_M1
SHUTTE R_M0
IN1
IN2
IN3
IN4
3
F LA S H_V P
BUZZER
Q2
F LA S H
+3.1V D
MEMORY STICK
LE NS
2
GREEN
+5V M
33.75MHZ
+13.4V
CAPACITOR
100UF 300V
SELF TIMER LED
1
1
DGND
+3.1VD
MS_ON
R/B
MS_INS#
C LE
WE
WP
ALE
CE0
RE
MS_C LK
MD[0..7]
F A23
F A20
F A22
F A21
1
F LA S H_RDY
4
DG ND
+3.1V D
4
S T RO B E _C HG
S T RO B E _T rg
RA MD[0..15]
RA MA [0..14]
RA MLDM
RA MW E _N
RA MC A S
RA MRA S
RA MC S _N
RA MLDQ S
RA MUDQ S
RA MUDM
RA MC LK _N
RA MC LK
RA MC LK _E N
RA MRE F
2
ME MO RY
SHUT1
SHUT2
PW _LE D
PW R_KE Y
3
DG ND
S HUT 1
S HUT 2
P W _LE D
P W R_K E Y
SHUT1
SHUT2
PW _LE D
PW R_KE Y
+3.1VD
IRIS(METER)
LC D
TOP
+3.1V D
LENS
+13.4V
+13.4V
+3.1V D
3
2
DS P
1
Out
P owe r 4
POWE R
GND_3
3
2
GND_2
MIC 1
S P M0204HD5
Q29
AO3415
3
MC4_4.72X3.76_173
G2412-0039-00
1
BATT+2
3
2
1
2
1
F3 1.6A/32V
1
-7.5V
VP
-7.5V
1
C186
FLASH_VP
2
R163
100K
2
C160
1
1
1
0 .1 U K _ 1 6 V _ X 5 R
R131
100K
2
0 .1 U K _ 1 6 V _ X 5 R
2
2
1
1
2
C159
2
BATT-2
1000P K _25V _X7R
C187
10 00P K _25V _X 7R
2
F5 1A/24V
Q42
AO3415
DSC-S730
3-1
4. REPAIR PARTS LIST
4-1.
EXPLODED VIEWS
4-1-1. OVERALL SECTION
ns: not supplied
3
15
4
6
13
16
18
2
19
11
5
10
(Note)
12
17
7
ns
14
15
9
Main Frame Block
(See Page 4-2)
1
8
Note : The adjustment is not required after replacing the LCD
• Refer to cover for mark
Ref. No.
.
Part No.
Description
1
2
3
4
5
X-2188-411-1
X-2188-412-1
3-286-696-01
3-286-697-01
3-286-698-01
CABINET (FRONT) ASSY
CABINET (REAR) ASSY
SHAFT, STRAP
BLOCK, RL
LCD
6
7
8
9
10
A-1444-049-A
3-286-700-01
3-286-701-01
3-286-702-01
3-286-703-01
ST BLOCK ASSY
SHAFT, BT LID
LID, BT
SPRING, BT LID
LID, JACK
Ref. No.
DSC-S730
4-1
Part No.
Description
11
12
13
14
15
3-287-023-11
3-287-026-01
3-287-028-01
3-287-027-01
3-287-025-01
SCREW M1.7 X 2.7
SCREW TP1.4 X 2.5
SCREW TP1.7 X 3.5
SCREW TP1.7 X 4
SCREW TP1.4 X 3
16
17
18
19
3-287-032-01
3-296-920-01
3-296-921-01
3-299-366-01
SCREW TP1.7 X 6.5
SCREW TP1.4 X 3.5
SCREW TP1.4 X 4
SCREW TP1.7 X 3.5
4. REPAIR PARTS LIST
4-1-2. MAIN FRAME BLOCK
ns: not supplied
ns
(Note 1)
104
104
102
102
103
ns
101
ns
(Note 1)
105
(Note 2)
Note 1 : In case of the lens block assy or main board failure,
contact your local Sony service Headquarter for
the measures.
Note 2 : When separate lens block assy and main board for
main frame replacement, assemble original lens block
assy and main board back after repaire.
Ref. No.
101
102
103
104
105
Part No.
Description
3-286-699-01
3-287-024-01
3-287-026-01
3-287-028-01
3-286-704-01
SUPPORT (JACK)
SCREW TP1.4 X 3
SCREW TP1.4 X 2.5
SCREW TP1.7 X 3.5
FRAME, MAIN
DSC-S730
4-2
4. REPAIR PARTS LIST
4-2.
ACCESSORIES
Checking supplied accessories.
Note 1: This item is supplied with the unit as an accessory,
but is not prepared as a service part.
A/V cable
3-196-980-01
USB cable
3-196-981-01
Wrist strap
2-050-981-01
Instruction Manual
3-281-198-11
3-281-198-21
3-281-198-31
3-281-198-41
3-281-198-51
3-281-198-61
3-281-198-71
3-281-198-81
3-281-198-91
3-281-199-11
3-281-199-21
3-281-199-31
3-281-199-41
3-281-199-51
3-281-199-61
3-281-199-71
(ENGLISH) (CND, AEP, UK, E, AUS, HK, JE)
(FRENCH, ITALIAN) (CND, AEP)
(SPANISH, PORTUGUESE) (AEP, E, JE)
(GERMAN, DUTCH) (AEP)
(TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, JE)
(RUSSIAN, UKRAINIAN) (AEP)
(ARABIC, PERSIAN) (E)
(KOREAN) (KR, JE)
(POLISH, CZECH) (AEP)
(HUNGARIAN, SLOVAK) (AEP)
(SWEDISH, FINNISH) (AEP)
(NORWEGIAN, DANISH)(AEP)
(THAI, MALAYSIAN) (E)
(TURKISH, GREEK) (AEP)
(ENGLISH, SPANISH) (US)
(SIMPLIFIED CHINESE) (CH)
LR6 (size AA) Alkaline Battery
(Note 1)
Cyber-shot Handbook(PDF)
The CD-ROM supplied contains all of language version of
the Instruction Manual in pdf (Cyber-shot Handbook.pdf) for printing.
The printed matter is not supplied. If required,
please order it with the part number below.
CD-ROM
(Cyber-shot application software/
"Cyber-shot Handbook"/
"Cyber-shot Step-up Guide")
*3-281-189-01
*
*
*
*
*
*
*
*
*
*
*
*
*
3-281-190-11
3-281-190-21
3-281-190-31
3-281-190-41
3-281-190-51
3-281-190-61
3-281-190-71
3-281-190-81
3-281-190-91
3-281-191-11
3-281-191-21
3-281-191-31
3-281-191-41
(ENGLISH)
(FRENCH)
(ITALIAN)
(SPANISH)
(PORTUGUESE)
(GERMAN)
(DUTCH)
(TRADITIONAL CHINESE)
(SIMPLIFIED CHINESE)
(RUSSIAN)
(ARABIC)
(PERSIAN)
(KOREAN)
NOTE:
Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
Abbreviation
AUS : Australian model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
JE : Tourist model
KR : Korea model
DSC-S730
4-3
*
*
*
*
*
*
*
*
*
*
*
*
*
3-281-191-51
3-281-191-61
3-281-191-71
3-281-191-81
3-281-191-91
3-281-192-11
3-281-192-21
3-281-192-31
3-281-192-41
3-281-192-51
3-281-192-61
3-281-192-71
3-281-192-81
(POLISH)
(CZECH)
(HUNGARIAN)
(SLOVAK)
(SWEDISH)
(FINNISH)
(NORWEGIAN)
(DANISH)
(THAI)
(MALAYSIAN)
(TURKISH)
(GREEK)
(UKRAINIAN)
【Regarding Fuse】
・MAIN BOARD
F5
F3
F5
MANUFACTURER: KAMAYA ELECTRIC CO.,LTD.
TYPE:
FCC10102AD
RATING:
1.0A
F3
MANUFACTURER: KAMAYA ELECTRIC CO.,LTD.
TYPE:
FCC16162AD
RATING:
1.6A
DSC-S730
Reverse
985223911.pdf
Revision History
Ver.
Date
1.0
2007.11
DSC-S730
History
Official Release
Contents
—
S.M. Rev.
issued
—