Download Lightolier IS:1155 User's Manual
Transcript
/ \ INSTRUCTION IS:1155 lN=ALLATION OF LYTECA~ER REFLEOTOR TRIM IN THE 1100 SERIES FRAME-IN-KIT WITH ROTO CLIPS _ R0487 READ AND UNDER~AND THESE INSTRUCTIONS BEFORE This fixture is intended for installation in accordance with the National code specifications. NOTE To prevent electrical SHEET NO. INSTALLING FIXTURE. Electrical Cods and local or federal at fuee box before proceeding. shock, turn off electricity Use this Instruction Sheet only when Lytecsster Trim is being Installed in the 1100 series Frsme-im Kits with Roto Cfips (see Fig. F). If not, disregsrd this Instruction Sheet. a %% FIG. B FIG. A 1. FRAME-fN FIG. C 2. ROTATE CLIPS FIG. D 4. SNAWN 3. SCREW4N FIG. E PUSH.UP WARNING: BEFORE installing REFLECTORTRiM lU FRAME-fN Km, READ MARKINGS IN REFLECTORTRIM AND IN SOCK= CUP OF FRAME.fN-KIT TO D~ERMINE LAMP WAT7AGE AND TYPE APPLICABLE FOR YOUR lNSTALLATfON. IF IC. TYPE FRAMING KIT IS USED, IT MAY BE iNSTAUED IN DiRECT CONTACT WITH INSULATED CEILING. IF A NON il$. TYPE ~ME-fN-KfT IS USEQ DO N~ iNWAU INSULATION WITHIN 3 INCHES OF FfXTURE SIDE OR WIRING COMPARTMENT, NOR ABOVE FIXTURE IN SUCH A MANNER TO ENTRAP HSAT. LONG LEG 1. FRAME-fN (Fig. A) See Frame-In-Kit Instruction Sheets for installation / SHORT LEG procedure. SPRING @ 2. ROTATE ROTO.CLIPS (Fig. B) Rotate (4) ROTO CLIPS eo that the short legs extend inwardly toward the center opening (Fig, F) / > .-..,.:. .... HOOK 0= N HOUSING NOTE return The SHORT LEG of the RCf70 CLiP hss NO on top. :3; q -..,, . ... 3. SCREW-IN MALE ADA~ER (Fig. C) Insert HOOK in ear of SPRING on SOCKET CUP and let HOUSING hang down (Fig. G). Screw SOCKET EXTENSION (MALE ADAPTER) into SOCKET in SOCKET CUi? 4. SNARON SOCK~ 50CKET cup HOUSING CUP (Fig. D) Disengage HOUSING from SOCKET CUP by pulling HOOK out of SPRING ear (Fig. H). Insert SOCKET CUP between slots on MOUNTING BRACKET making sure SPRINGS snap into slots of MOUNTING BRACK= (Fig. l). 5. PUSH-UP HOUSING FIG. H (Fig. E) Tilt HOUSING and inserf SOCKET CUP opening on opposite side of JUNCTION houeing and push it up into ceiling. into ceiling BOX. Pivot SPRING SOCKETCUP MOUNTING US, PATENT NO 4,313,154;4,327,403. FOREIGN PATENTs PENDING BRACKET FOR OTHER REFLECTOR TRIMS Eyebell (1162), etc See bsck pS9e @ SEC AU CUS, [mg<~[=[~<>[m[l~g? MONTREAL, NEW JERSEy,07094.0508 Q”EBEC, CANADA 1s1155 R0487 IN!YCALLATION OF ADJUSTABLE ACCENT LIGHT TRIM) LAMP HOLDER SUPPORT LAMP CONNECTOR > w HOUSING 8. Install proper wattage PAR36 LAMP into IAMP CONNECTOR, making certain the LAMP is seated all the way into the IAMP CONNECTOR. 9. Insert LAMP into LAMPHOLDER RINGS so that face of LAMP is seated, and extended through hole in the LAMPHOLDER RING, and put the lamp and ring back into the LAMPHOLDER SUPPORT so that the LAMP SPRINGS now support all. VOLTAGE swHG- 6. Remove lAMPHOLDER RING from within HOUSING by pulling straight down, and disengaging ths LAMP SPRINGS which also act se a holding mechanism for lAMPHOLDER RING. 7. Select voltage (12v., 25-50 Watt, or 5.5v, 25 Watt) depending on lamp being used? by setting SLIDE SWITCH (Fig. J). Insert screwdriver into slot and slide switch if not already set according to lamp being used (See Fig. K). (LOW LAMP=------ LAMP HOLDER ~ RING FIG. J ti~. Q “\- \H \. \ m4srALumor4 OF EVEBALL (mw A . ......’ /“ FIG. K VOLTAGE TRIM) 6. Remove APERTURE TRIM from within EYEBALL by pullin straight down, and disengaging from SUPP?)RT SPRINGS (Fig. L). SLID 7. Select voltage (12v., 25-50 Watt, or 5.5v, 25 Watt) depending on lamp being used! by eetting SLIDE SWITCH (Fig. L). Insert screwdrwer into slot and slide switch if not alreedy set according to lamp being used (See Fig. K). 6. Install proper wattage PAR36 LAMP into LAMP CONNECTOR, meidng certain the LAMP ia seated all the way into the IAMP CONNECTOR (Fig, L). 9. Insert LAMP into LAMP SPRING. co 10, Insert APERTURE TRIM, and LAMP into EYESALL until groovee on APERTURE TRIM engage into SUPPORT SPRINGS [FiO. L). NOTE LOW VOLTAGE &i+lJRE6 should be dimmed only with speclel dimmers Mended for that purpose. Use Ughtoller Preolslon LV, Eoeniet, or Lytemcds, or equlvelerrt products ~others or vsrieble eutc-transformers or eleotrcn c dimmers intended for uee with low voltege flsturss. NOTE law voltege flstures may produce sudible sound when used with externel dimme~ which mey be objectlonsl In acoustically critlcsl srea% WARNING REFLECIUR HAZARD. FIG. L USE ONLY REFLECIOR TRIMS PROVIDED SV LIGHTDLIER INC. USE OF ~HER MANUFACTURERS TRIMS VOIDS THE UNDERWRITERS IABOFIA30RIES L16TING AND COULD CONSIWIJTE A FIRE