Download LG TL-AT130M User's Manual
Transcript
TIME LAPSE VCR SERVICE MANUAL CAUTION BEFORE SERVICING THE UNIT, READ THE “SAFETY PRECAUTIONS” IN THIS MANUAL. MENU REC REW F.F REV CUE POWER / TIMER MOVE SEL TRACKING ALARM UP DOWN KEY LOCK REC / PB SPEED PAUSE / STILL PLAY / REC CHK STOP / EJECT APRIL, 2006 Printed in Korea 2 TABLE OF CONTENTS SECTION 1 SUMMARY • SPECIFICATIONS ......................................................1-1 • LOCATION OF CUSTOMER CONTROLS .................1-2 • CRITICAL PARTS REPLACING TIME TABLE...........1-5 • CRITICAL PARTS DESCRIPTION .............................1-5 SECTION 2 CABINET & MAIN FRAME EXPLODED VIEWS........................................................2-1 1. Cabinet and Main Frame Section ............................2-1 2. Packing & Accessory Section ..................................2-3 BLOCK & CIRCUIT DIAGRAMS....................................3-13 1. OVERALL WIRING DIAGRAM ...............................3-13 2. POWER BLOCK DIAGRAM ...................................3-15 3. POWER CIRCUIT DIAGRAM .................................3-17 4. AUDIO BLOCK DIAGRAM......................................3-19 5. Y/C BLOCK DIAGRAM ...........................................3-20 6. A/V CIRCUIT DIAGRAM.........................................3-21 7. SYSTEM BLOCK DIAGRAM ..................................3-24 8. SYSTEM CIRCUIT DIAGRAM................................3-27 9. JACK CIRCUIT DIAGRAM .....................................3-29 10. KEY-BOARD CIRCUIT DIAGRAM..........................3-31 PRINTED CIRCUIT DIAGRAMS ....................................3-33 1. MAIN P.C.BOARD ..................................................3-33 2. KEY 1 P.C.BOARD .................................................3-35 3. KEY 2 P.C.BOARD .................................................3-35 4. JACK P.C.BOARD ..................................................3-35 SECTION 3 ELECTRICAL SECTION 4 MECHANISM ELECTRICAL ADJUSTMENT PROCEDURES .............3-1 1. PG ADJUSTMENT..................................................3-1 ELECTRICAL TROUBLESHOOTING GUIDE ...............3-2 1. POWER(SMPS) CIRCUIT ......................................3-2 2. SERVO CIRCUIT....................................................3-4 3. Y/C CIRCUIT ..........................................................3-6 4. AUDIO CIRCUIT .....................................................3-9 5. SYSTEM/KEY CIRCUIT .........................................3-11 6. OSD CIRCUIT.........................................................3-12 NOTE) The table of contents for this section is edited separately. SECTION 5 REPLACEMENT PARTS LIST • Mechanical Section.....................................................5-1 • Electrical Section ........................................................5-3 SECTION1 SUMMARY SPECIFICATIONS GENERAL Head System Power Source Power Consumption Back up time (clock) Dimensions (WxHxD) Operating Temperature Operating Humidity Timer Weight Tape Speed (NTSC) Tape Speed (PAL) Maximum Recording Time Tape Width Rewind Time Video Signal System(PAL) Video Signal System(NTSC) Video Input Video Output Signal to Noise Ratio Conventional audio Input (LINE) Output (LINE) S/N Ratio Frequency Range Four head helical scan azimuth system AC 100-240V, 50/60Hz Approx. 15 Watts 30 days 14.2” x 3.7” x 10.7” (360 x 94 x 273 mm) 41 °F~105 °F (5 °C~40 °C) Less than 80% RH 24-hour display type Approx. 8.4 lb (3.8 kg) 11.12 mm/sec (6H) , 3.70 mm/sec (18H), 2.22 mm/sec (30H), 72H ~ 960H 11.695 mm/sec (6H) , 3.89 mm/sec (18H), 2.33 mm/sec (30H), 72H ~ 960H 6 hours (NT:T-120/PAL:E-180, 6H), 18 hours (NT:T-120/PAL:E-180, 18H), 30 hours (NT:T-120/PAL:E-180, 30H), 72H ~ 960H 0.5 in. (12.7 mm) About 65 seconds (NT:T-120)(PAL:E-180) CCIR Standard (625 lines, 50 fields) PAL type color signal EIA Standard (525 lines, 60 fields) NTSC type color signal 1.0 Vp-p 75 ohms unbalanced 1.0 Vp-p 75 ohms unbalanced More than 43 dB (6H mode) -6.0 dBm more than 47 kohms -6.0 dBm less than 1.5 kohms More than 43 dB (6H mode) 200 Hz to 10kHz (6H mode) * Designs and specifications are subject to change without notice. * Weight and dimensions shown are approximate. 1-1 SECTION1 SUMMARY LOCATION OF CUSTOMER CONTROLS FRONT 1 2 3 4 5 6 7 8 9 POWER/TIMER BUTTON MENU BUTTON REC (RECORD) BUTTON MOVE BUTTON SEL (SELECT) BUTTON DOWN BUTTON UP BUTTON ALARM INDICATOR KEY LOCK INDICATOR 10 CASSETTE LOADING SLOT 11 CLEAR, KEY LOCK OFF, BUZZER OFF 12 CLOCK, COUNT, REMAIN 13 SHUTTLE RING 14 JOG RING 15 PAUSE/STILL BUTTON 16 PLAY/REC CHECK BUTTON 17 STOP/EJECT BUTTON REAR 1 POWER CORD 2 AUDIO IN/OUT JACK 3 VIDEO IN/OUT JACK 4 RESET BUTTON 5 12-PIN TERMINAL BLOCK 1-2 SECTION1 SUMMARY LOCATION OF CUSTOMER CONTROLS INDICATOR PANEL 1 2 3 4 5 6 TIME LAPSE VCR TIME INDICATION ALARM INDICATION SERIES INDICATION RECORD INDICATION TIMER INDICATION CASSETTE INDICATION 7 INDEX INDICATION 8 POWER FAILURE INDICATION 9 KEY LOCK INDICATION 10 REPEAT INDICATION 11 FUNCTION INDICATION 12 VCR FUNCTION INDICATION VCR FUNCTION INDICATION 1-3 SECTION1 SUMMARY LOCATION OF CUSTOMER CONTROLS TERMINAL SIGNAL LEVELS TERMINAL SIGNAL LEVEL IN/OUT DESCRIPTION 1. ALARM IN VIH : 4 ~ 5V VIL : 0 ~ 0.6V T : above 250 msec INPUT The input signal that makes ‘Alarm Record’ work 2. ALARM OUT VIH : 4 ~ 5V VIL : 0 ~ 0.6V T : ALARM REC STATE OUTPUT Outputs whether ‘Alarm Recording’ is working 3.ALARM RESET VIH : 4 ~ 5V VIL : 0 ~ 0.6V T : above 250 msec INPUT The terminal that stops ‘Alarm Record’ in Auto mode 5. SERIES IN VIH : 4 ~ 5V VIL : 0 ~ 0.6V T : above 250 msec INPUT The input terminal to make ‘Series Record’ work 6. SERIES OUT VIH : 4 ~ 5V VIL : 0 ~ 0.6V T : above 250 msec Output signal appears when the OUTPUT tape reaches to end or deck is error in recording. 7. WARNING OUT VIH : 4 ~ 5V Outputs whether VCR deck is VIL : 0 ~ 0.6V OUTPUT error. T : until any-key is pressed 8. TRIGGER OUT The signal is output which is used by VIH : 4 ~ 5V, VIL : 0 ~ 0.6V several cameras in 8 msec : NTSC OUTPUT switching general space with using camera 10 msec : PAL multi-plexer. 10. LOW TAPE OUT As the terminal that outputs that tape VIH : 4 ~ 5V less than 5 minutes in OUTPUT remains VIL : 0 ~ 0.6V recording, it isn’t output in ‘1-shot T : below 5 min, end of tape Record’. 11. 1-SHOT REC IN VIH : 4 ~ 5V VIL : 0 ~ 0.6V T : above 250 msec INPUT 0V COMMON 4, 9, 12. GND - 1-4 The terminal that makes ‘1-short Record’ work in Auto mode SECTION1 SUMMARY CRITICAL PARTS REPLACING TIME TABLE No. DESCRIPTION 1 1500 3000 5000 6000 7500 9000 10000 12000 Test freatures DRUM ASSY Specification RF out level -4dB and below 2 ARM ASSY CLEANER Wear status Whether extraneous matters come out 3 MOTOR CAPSTAN (D-35) W/F(WTD) 0.4% and below 4 BELT CAPSTAN Belt tension Variation amount : within 40% 5 BASE ASSY A/C 6 HEAD F/E 7 ARM ASSY IDLER 8 HOLDER ASSY PINCH Audio and CTL out level The rate of erasing (1KHz) The capacity of ldler for moving Surrace solidity of Roller 9 BAND ASSY TENSION Back Torque 40~70 g 10 HOUSING ASSY CST loading status there shouldn’t be any space betwween CST and compartment 11 CAPSTAN SOFT BRAKE Felt wear whether there is touch noise 12 CLUTCHAY Torque(Play, Rev) 40~140gcm, 100~210gcm Reference : Changing Cleaning -6dB and below 45dB min 4~12 g 60~90 Checking Notes : • Check the running path adjustment when you change the itens 1, 3, 5, 6 and 10. • Check the back tension when you change Band Assy Tension. CRITICAL PARTS DESCRIPTION 1. Drum Ass’y Consists of video head, rotary trans and motor. records video and audio information on the tape, and play the tape back.(Audio information is recorded only on the Hi-Fi models) 2. Arm Ass’y Cleaner Cleans video head and rotation head automatically. 4. Motor Capstan Moves the tape with regular speed. 5. Belt Capstan Transfers rotative energy of capstan motor to the driving system. 6. Brake Ass’y Capstan Brakes rotative energy of capstan motor. 7. Base Ass’y A/C Consists of three head. Audio erase head in the left upper erases audio signal in dubbing. Audio head in the right upper records and playes the audio signal. CTL head in the right lower records and detects CTL pulse to control tape speed. 8. Head F/E Is abbreviation of Full Erased Head. erases the signal recorded on a tape clearly and absorb vibration of tape. 12. Arm Ass’y Idler Is located between T/UP reel and supply reel. Transfers ratative energy of capstan motor to T/UP reel or supply reel. 13. Holder Ass’y Pinch Sticks a video tape to capstan motor and has the tape played without being slipped from capstan motor axle. 14. Band Ass’y Tension Has supply reel loosened properly with giving it some tensile force. 15. Arm Ass’y Makes the cassette tape inserted be loaded and ejected precisly and safely. 16. Clutch Ass’y Plays the tape with trasfering rotative energy of capstan motor to idler reel. 1-5 SECTION2 CABINET & MAIN FRAME EXPLODED VIEWS 1. Cabinet and Main Frame Section Cabinet & Main Frame Section Parts list MODEL : TL-AT130M S AL LOCA.NO. PART NO A00 A42 A43 A44 A45 A46 6721R-0771U 6871R-8283A 3721R-F826D 6871R-4462A 6871R-7050B 3501R-7050B 250 260 277 278 280 281 283 284 285 286 300 320 3110R-S040F 3210R-0023A 4940R-Z075A 4940R-Z076B 3720R-F721D 524-013A 3580R-V090A 442-681A 4940R-Z086A 4940R-S017A 6410RZHV01A 3721R-D031N 323 325 330 3111R-0089B 4931R-0024D 3550R-0210A 452 457 462 353-051A 353-051E 353-136A RUN DATE : 2004.03.12 DESCRIPTION ASSEMBLY SECTION DECK ASSEMBLY,VIDEO PWB(PCB) ASSEMBLY,TOTAL PANEL ASSEMBLY,FRONT PWB(PCB) ASSY,TOTAL PWB(PCB) ASSEMBLY,TOTAL BOARD ASSEMBLY PARTS SECTION CASE FRAME KNOB KNOB PANEL,VIDEO MAGNET DOOR SPRING KNOB KNOB POWER CORD PANEL ASSEMBLY, DISTRIBUTOR[NOR CASE ASSY HOLDER ASSEMBLY COVER SCREW SCREW,DRAWING SCREW,DRAWING SCREW,DRAWING 2-1 SPECIFICATION DECK/MECHA D35 LG T/L (4HD(ALL T/L VCR KEY2 JOG/SHUTTLE CCD TIME LAPSE PANEL FRONT ASS TL-AR30 (SERIES) - W. RS232C T/L VCR TL-AT130M MAIN VCR TL-AT130M MAIN LV-TL1960 2960 MOLD AIRHALL BA VCR - MAIN SHUTTLE(TL-AR30M) CCD TL-AT130 MOLD CCD LV-TL1960 S MOLD HIPS 40AF VCR - ASSY DOOR CCD TIME LAPSE MOLD DOOR CST DOOR CCD LV-TL124 MOLD SLIDE (LV-TL24) IT10S2(6A/250V) VOLEX IMMETRO LV-TL1960S 2960S NEW ASSY (RSPRE-AMP (PBSB-SH) DIGI(MONO-ENABLE) BOTTOM(LARGE) SPECIAL SPECIAL (3X12) SPECIAL(FBK) (353S353A) REMARKS SECTION2 CABINET & MAIN FRAME EXPLODED VIEWS 1-1. Cabinet and Main Frame Section Cabinet & Main Frame Section Parts list ASSEMBLY PARTS SECTION A42 6871RK5700K Ass'y Front PCB SNILN4T3526 A43 05503805 ASS'Y FRONT CAVINET NTH960 C-TYPE A44 6871R-4462A Ass'y Ant. PCB TL-AR30(SERIES) A46 3501RK3200B Ass'y Main PCB CCD LV-TL1960 2-2 SECTION2 CABINET & MAIN FRAME EXPLODED VIEWS 2. Packing & Accessory Section ✒ NOTE Refer to “REPLACEMENT PARTSLIST” in order to look for the part number of each part. 801 INSTRUCTION ASS’Y 803 : PACKING 804: SHEET ROLL 802: BOX CARTON • Packing Accessory Section Parts list MODEL : TL-AT130M S AL LOCA.NO. 801 802 803 804 808 900 PART NO 3835RS0069N 3890R-C065K 3920R-E016A 3858R-S001A 534-008C 6711R1P041H RUN DATE : 2004.03.12 DESCRIPTION INSTRUCTION ASSEMBLY BOX,MASTER PACKING SHEET (MECH) BATTERY,MANGANESE REMOTE CONTROLLER ASSEMBLY 2-3 SPECIFICATION REMARKS CCD TL-AT330M-AABBDL1_ENG_POR_ TL-AT330M AABBDL . 1 Packing LV-TL24I 0.02 0 EPS 10 Packing LDPE 600M 630MM 0.5 VC AAAM(R03) SEOTONG 1-5 V - 1PA P9 LV-TL1960 SECTION3 ELECTRICAL ELECTRICAL ADJUSTMENT PROCEDURES 1. PG ADJUSTMENT MODE SPECIFICATION OBJECT MEASURED OBJECT ADJUSTED PLAYBACK IN SP PG : 416 ± 20 sec V.OUT JACK VR501 1. Connect CH-1 of the oscilloscope to W357 and W362, and adjust it to 1Vp-p as TRIGGER. (In case of 10:1 Probe, adjust it 50m Vp-p) 2. Connect CH-2 of the oscilloscope to V.OUT JACK and adjust it to 0.5Vp-p. (In case of 10:1 Probe, adjust it 50 Vp-p) 3. Adjust time of the oscilloscope to 0.1 msec. 4. Adjust the range between FLLING EDGE part of video vertical trigger signal and video vertical trigger signal to the specification(416±20 sec) with changing VR501. WAVEFORM • CONNECTION CHART OF MAIN PWB Fig 3-1. Connection chart of PG adjustment ✒ Caution When repairing the power part just after pulling out the power code, there is hazard of electical shock caused by the charged electricity at the peripheral circuit component(primary power) such as condenser C807(150µF). So begin repairing after doing procedure below. 1. Set the volt meter up to resistance measurement.(In case of digital volt meter, set it up to over 20MΩ.) 2. Discharge electicity with putting the measuring terminal lines(+, 1 probe) of volt meter at the ends of condenser C103.(You don’t have to put the polarity of the measuring terminal lines on the same polarity of the condenser.) 3-1 SECTION3 ELECTRICAL ELECTRICAL TROUBLESHOOTING GUIDE 1. Power Circuit(SMPS) (1) No 5.3 A (2) No 9V No 5.3V Is F101 normal? No 12V NO Replace F101(Use a specified Is D109 normal? fuse). YES Is BD101 normal? NO Is Q170 normal? Replace BD101. NO Replace Q170 YES NO Replace R101. Is D110 normal? NO Replace D110 YES YES Is there Vcc (about 13~19V) at Check/Replace D109 YES YES Is R101 normal? NO NO IC101 pin 5? NO Is D103 normal? Is Q152 normal? Replace Q152 YES NO Check/ Check/ Replace Q163 Replace D103 YES Is D106 normal? NO Replace D106. (3) No 24 V YES Is there about 2.5V at NO IC103 pin 1? No 24V Replace IC103. YES Is D109 normal? NO Replace D109. Is D110 normal? Check/Replace D110 YES YES Is L103 normal? NO NO Is Q159 normal? Is L103 normal? YES YES Check the power terminal at main Check ‘H’ signal at Q161 Base terminal PCB short. 3-2 NO Check/Replace Q152 SECTION3 ELECTRICAL ELECTRICAL TROUBLESHOOTING GUIDE (4) No 5.2 A (TO AVCP, BIAS) (5) No 10V No 5.2V Is D106 normal? No 10V NO Is D109 normal? Replace D106. YES Is Q153 normal? Replace D109 YES NO Is Q170 normal?, Is there about Replace Q153. 13.5V at Q107 Base? YES YES Is there voltage (about 0V) NO NO Check/ Replace Replace Q157. at Q157 collector. D155, D156, D157/\. YES Check/ Replace Q156 3-3 NO Check/ Replace Q107, ZD103 SECTION3 ELECTRICAL ELECTRICAL TROUBLESHOOTING GUIDE 2. SERVO CIRCUIT (1) Video is unstable in PB mode In PB mode Does noise level on the screen change periodically? YES Does CTL pulse appear at NO IC501 Pin 76? NO Is adjusting height of CTL Readjust the height of CTL fead. head accurate? YES NO Replace IC501. Does CTL pulse move on tracking? YES Does Video Envelope wave form NO appear at IC501 pin 86? Check the Pre-Amp circuit YES Replace IC501. (2) Drum motor stops When the drum moter stop NO Is there 12V at PMC01 Pin8? Check Power circuit YES NO Is there 2.8V at PMC01 Pin12? YES NO Does Drum PWM pulse PMC01 Pin3? appear at IC501 Pin34? YES Does DFG pulse appear at YES NO Check the Ass’s between Aren’t pattern or componets between Check the Ass’y between connector(PMC01) and Drum motor IC501 Pin34 and PMC01 Pin12 short? junction PCB and Drum motor Does DFG pulse appear at IC501 Pin65? NO Aren’t pattern or componets between IC501 Pin34 and PMC12 Pin1 short? YES Does Drum PWM pulse appear NO at IC501 Pin34? YES Aren’t pattern or componets between IC501 Pin34 and PMC01 Pin12 short? 3-4 Replace IC501 SECTION3 ELECTRICAL ELECTRICAL TROUBLESHOOTING GUIDE (3) Capstan motor stops When the capstan motor stops Is it 12VA at PMC01 Pin2? NO Check Power circuit YES NO Is there 2.8V at PMC01 Pin9? Does PWM signal appear at IC501 Pin 33? YES YES Check the Ass’y between PMC01 NO and Capstan motor YES Aren’t pattern or componets between Does CFG signal appear at PMC01 Pin1? IC501 Pin33 and PMC01 Pin9 short? YES NO Check the Ass’y of Capstan motor Check CFG signal appear at IC501 NO Pin67? Aren’t pattern or componets between IC501 Pin67 and PMC01 Pin1 short? YES Does Capstan PWM signal appear at IC501 Pin33? NO Replace IC501 YES Aren’t pattern or componets between IC501 Pin33 and PMC01 Pin1 short? 3-5 SECTION3 ELECTRICAL ELECTRICAL TROUBLESHOOTING GUIDE 3. Y/C CIRCUIT (1) No Video in EE Mode No Video in EE Mode Does the Video signal appear at the NO Check the Video input Jack & IC3G1 Pin9? jack Board connection. YES Does the Video signal appear NO Check the IC3G1 Pin14 at the IC301 Pin38? and Q3G1 emitter. YES Is 5V applied to the NO Check the 5VA Line. IC301 Pin16, 40, 55, 58, 75, 87? (Power Circuit) YES Does the Video signal appear NO at the IC301 Pin29? NO IC301 Pin 23, 24? NO at the IC501 Pin 47? Check the path of the signal between NO the IC301 Pin29 and IC501 Pin49. YES Does the Video signal appear at the Emitter terminal of the Q380? Check the System Circuit. (Refer to 2 ‘SYSTEM I C BUS Trouble Shooting’) YES YES Does the Video signal appear 2 Is I C BUS signal applied to the Check C316.(AGC) YES NO Is there 9V on the plus NO terminal of the C381? Replace the IC301. YES Check the 9V Line. Replace the Q380. (Power Circuit) 3-6 SECTION3 ELECTRICAL ELECTRICAL TROUBLESHOOTING GUIDE (2) When the Y(Luminance)signal doesn’t appear on the screen in PB Mode. Is 5V applied to the IC301 Pin 16, 40, 55, 58, 87? Is the I2C Bus signal applied NO Check the line of the 5.3VA Line. (Power Circuit) NO Check the System Circuit. (Refer to 2 to the IC301 Pin 23, 24? ‘SYSTEM I C BUS Trouble Shooting’) YES Does the normal RF signal NO appear at the IC301 Pin74? Is the V.H.S/W "H" about NO Check the System Circuit. (IC501 Pin 23) 3.4V to the IC301 Pin11 ? YES Is V.H.S/W "H" about 3.4V at the NO IC301 Pin 11? YES Check the V.H.S/W level. (Check R304, R305) YES NO Clean the Drum. Does the Y(Luminance) RF signal NO appear at the IC301 Pin 17? Check the path of the Y(Luminance) Replace the IC301. YES RF signal.(Check the Q301) YES Is the Y(Luminance) Video waveform showed up at the IC301 Pin 41? NO Check the path of the Y(Luminance) YES RF signal.(Check Q302, Q303) YES Replace the IC301. 3-7 SECTION3 ELECTRICAL ELECTRICAL TROUBLESHOOTING GUIDE (3) When the C(Color) signal doesn't appear on the screen in PB Mode NO Is 5V applied to the IC301 Pin 16, 40, 55, 58, 87? Is the Color Rotary signal applied to Check the line of the 5.3VA Line. (Power Circuit) NO Check the Color Rotary the IC301 Pin 10? Circuit. (IC501 pin 98) YES NO Is Color Rotary "H" about Check the Color Rotary level. 1.6V? (Check the R302, R303) YES Does the Color signal appear at the IC301 Pin 71? NO Does the X301(4.43MHz) or NO X302(3.58MHz) oscillate? Replace the X301 or the X302. YES Does the Color signal appear NO YES Check the Color Pass. (Check the Q304) at the IC301 Pin 61? YES Check the circuit of the Replace the IC301. NO Replace the IC301. IC301 Pin 35, 62. (4) When the Video signal doesn't appear on the screen in REC Mode. Is the EE signal normal? Is 5V applied to the IC301 NO Check EE Mode. NO Pin 16, 40, 55, 58, 87? Check the line of the 5.3VA Line.(Power Circuit) YES Does PB Mode operate NO Check PB Mode. normally? YES Does the RF signal appear at the IC301 Pin 12? NO Is the REC 'H' signal (about NO 4V)applied to the IC301 Pin 30? Check the System of REC 'H' (the IC501 Pin 30 / the D301) YES Check REC Luminance the IC301 Pin90? Replace the IC301. Pass & Color Pass. YES Does the REC RF signal appear at YES NO Check the circuit of the YES IC301 Pin 90, 92, 94 YES Check the Drum & Drum Connector 3-8 SECTION3 ELECTRICAL ELECTRICAL TROUBLESHOOTING GUIDE 4. AUDIO CIRCUIT (1) No sound in EE Mode (2) No sound in PB MODE No sound in EE Mode. No sound in PB Mode. YES YES No sound. No sound. YES YES NO Is 5V applied to the IC301 Pin 75? Check the line of the 5V Line. Is 5V applied to the (Power Circuit) IC301 Pin 75? NO Check the line of the 5V Line. (Power Circuit) YES YES Is the Audio signal applied to the NO IC301 Pin 76? 2 Does the CLK/Data signal(I C) Check the path of appear at the IC301 Pin 23, 24? LINE/AUDIO. YES YES Does the Audio signal appear at the IC301 Pin 96? NO NO Check the connecting State between to the IC301 Pin 10? the P3D02 Pin 6 and A/C Head. out Jack. (Audio Mute "H".) at the IC301 Pin 96? NO YES Check the IC501 Pin18(CLK), NO YES YES Does the Audio signal appear appear at the IC301 Pin 23, 24? NO at the IC301 Pin 1? Check the IC501 Pin 2. 2 17(Data) Line. Does the Audio signal appear Check the connection of the Audio Does the CLK/Data signal(I C) Check the IC501 Pin 18(CLK), Is the Audio Mute "High" signal applied YES YES NO Replace the IC301 17(Data) Line. YES Replace the IC301 3-9 Is the Audio Mute "H" applied to the IC301 Pin 10? NO YES Check the IC501 Pin2. SECTION3 ELECTRICAL ELECTRICAL TROUBLESHOOTING GUIDE (3) No sound in REC Mode. NO sound in REC Mode. YES Sound is not recorded. YES Is Playback O.K.? NO Refer to "No sound in PB Mode,". YES Is the Audio signal applied NO Check the path of Line Audio. to the IC301 Pin 76? YES Does the Audio waveform appear NO Is the “High” signal applied to the NO IC301 Pin 10? at the IC301 Pin 7? YES Check the CLK/Date line and replace the IC301 YES Is 5V applied to the FL401 Check the IC501 Pin 96 Pin 2? YES (Audio Mute “H”). NO Check the line of the 5V Power Circuit. Is 3.0~4.5V applied to the Emitter of the Q481? YES NO Does the Erase signal appear at the FL401 Pin 6? YES NO Replace the FL401 or the Q405. Is the Voltage level of the IC301 Pin6 850mVp-p? NO Check the Audio R/P/E connector and Head. 3-10 SECTION3 ELECTRICAL ELECTRICAL TROUBLESHOOTING GUIDE 5. SYSTEM/KEY CIRCUIT (1) AUTO STOP Auto Stop YES Does SW waveform appear at IC501 NO pin23? Check Drum motor signal YES Does T/up reel pulse appear at IC501 Pin27? YES NO Does T/up reel pulse appear NO Is there 5.3V at RS501? at Q514 Base terminal? YES NO YES Replace T/up reel sensor of deck Replace IC501 Check DP06, LP03 Check power circuit (2) No cassette tape loading No cassette tape loading YES NO Is there REG. 12V at PMCQ1 Pin8? Check power circuit L104. YES NO Does 'H' signal appear at IC501 Is there 5.3V at IC501 Pin73? Pin62 while inserting CST? YES Check CST SW and peripheral circuit Check power circuit NO YES NO Check D106, L103. Check IC501 Pin7, 8, 9, 10 Check Deck mechanism *Caution : Auto stop can occur because Grease or Oil is dried up 3-11 SECTION3 ELECTRICAL ELECTRICAL TROUBLESHOOTING GUIDE (3) No Key display No Key display YES Is there 5.2VA at IC501 Pin79, 80, 81? NO Check power circuit YES As pressing the byttons doeseach NO Replace bad switches function work properly? 6. OSD CIRCUIT (2) No F.OSD display. (1) No OSD display. No F.OSD display. No OSD display. YES YES Is there 5.3V IC501 Pin 51? NO Check 5.3V Line of power Refer to “(5) No OSD picture” NO Does video signal appear at Replace X502. IC501 Pin 50? IC501 PIns 37, 38? YES YES NO Check peripheral circuit and replace X501 Does oscillation appear at the IC501 Pins 40, 41? Replace IC501 YES NO Does Video signal appear at the IC501 Pin 47? Check power Vcc 9V YES YES Does oscillation appear at the NO circuity. Check the signal between IC501 Pin47 and V.out Jack. YES Replace IC501. 3-12 NO Check the signal between IC301 Pin 29 and IC501 Pin 49. SECTION3 ELECTRICAL BLOCK & CIRCUIT DIAGRAMS 1. OVERALL WIRING DIAGRAM 3-13 3-14 SECTION3 ELECTRICAL BLOCK & CIRCUIT DIAGRAMS 2. POWER BLOCK DIAGRAM 3-15 3-16 SECTION3 ELECTRICAL BLOCK & CIRCUIT DIAGRAMS 3. POWER CLRCUIT DIAGRAM 3-17 3-18 SECTION3 ELECTRICAL BLOCK & CIRCUIT DIAGRAMS 4. AUDIO BLOCK DIAGRAM 3-19 SECTION3 ELECTRICAL BLOCK & CIRCUIT DIAGRAMS 5. Y/C BLOCK DIAGRAM 3-20 SECTION3 ELECTRICAL BLOCK & CIRCUIT DIAGRAMS 6. A/V CIRCUIT DIAGRAM 3-21 3-22 SECTION3 ELECTRICAL BLOCK & CIRCUIT DIAGRAMS 3-23 SECTION3 ELECTRICAL BLOCK & CIRCUIT DIAGRAMS 7. SYSTEM BLOCK DIAGRAM 3-24 3-25 SECTION3 ELECTRICAL BLOCK & CIRCUIT DIAGRAMS 3-26 SECTION3 ELECTRICAL BLOCK & CIRCUIT DIAGRAMS 8. SYSTEM CLRCUIT DIAGRAM 3-27 3-28 SECTION3 ELECTRICAL BLOCK & CIRCUIT DIAGRAMS 9. JACK CLRCUIT DIAGRAM 3-29 3-30 SECTION3 ELECTRICAL BLOCK & CIRCUIT DIAGRAMS 10. KEY-BOARD CLRCUIT DIAGRAM 3-31 3-32 SECTION3 ELECTRICAL PRINTED CIRCUIT DIAGRAMS 1. MAIN P.C.BOARD 3-33 3-34 SECTION3 ELECTRICAL PRINTED CIRCUIT DIAGRAMS 2. KEY 1 P.C.BOARD 3. KEY 2 P.C.BOARD PRINTED CIRCUIT BOARD DIAGRAMS 4. JACK P.C.BOARD 3-35 SECTION 4 MECHANISM CONTENTS DECK MECHANISM PARTS LOCATIONS • Top View......................................................4-1 • Bottom View ...............................................4-1 DECK MECHANISM DISASSEMBLY 1. Drum Assembly .........................................4-2 2. Plate Top ...................................................4-4 3. Holder Assembly CST ...............................4-4 4. Opener Door .............................................4-4 5. Bracket Assembly L/D Motor.....................4-4 6. Gear Assembly Rack F/L ..........................4-4 7. Arm Assembly F/L .....................................4-4 8. Lever Assembly S/W .................................4-4 9. Arm Assembly Cleaner..............................4-5 10.Head F/E ...................................................4-5 11. Base Assembly A/C Head .........................4-5 12.Brake Assembly T .....................................4-6 13.Brake Assembly RS ..................................4-6 14.Arm Assembly Tension..............................4-6 15.Reel S / Reel T..........................................4-6 16.Base Assembly P4 ....................................4-7 17.Opener Lid ................................................4-7 18.Arm Assembly Pinch .................................4-7 19.Lever T/up / Arm T/up ...............................4-7 20.Belt Capstan/Motor Capstan .....................4-8 21.Lever F/R ..................................................4-8 22.Clutch Assembly D35 ................................4-8 23. Brake Assembly Capstan .........................4-8 24.Gear Drive/Gear Cam ...............................4-9 25.Gear Sector...............................................4-9 26.Plate Slider................................................4-9 27.Lever Tension ............................................4-9 28.Lever Spring..............................................4-9 29.Gear Assembly P2/ Gear Assembly P3 ..................................4-10 30.Base Assembly P2/ Base Assembly P3 ..................................4-10 31.Base Loading ..........................................4-11 32.Base Tension ...........................................4-11 33.Arm Assembly Idler .................................4-11 DECK MECHANISM ADJUSTMENT • Tools and Fixtures for Service ...............4-12 1. Mechanism Alignment Position Check....4-13 2. Preparation for Adjustment......................4-14 3. Checking Torque .....................................4-14 4. Guide Roller Height Adjustment..............4-15 4-1. Preliminary Adjustment ....................4-15 4-2. Precise Adjustment ..........................4-15 5. Audio/Control (A/C) Head Adjustment ....4-16 5-1. Preliminary Adjustment ....................4-16 5-2. Confirmation of Tape Path between Pinch Roller and Take-up Guide ......4-17 5-3. Precise Adjustment(Azimuth Adjustment) .........................................................4-17 6. X-Value Adjustment .................................4-17 7. Adjustment after Replacing Drum Assembly (Video Heads) .........................................4-18 8. Check the Tape Travel after Reassembling Deck Mechanism.....................................4-18 8-1. Checking Audio and RF Locking Time during Playback after CUE or REV .........................................................4-18 8-2. Checking for Tape Curling or Jamming ..........................................4-18 MAINTENANCE/INSPECTION PROCEDURE 1. 2. 3. 4. Check before starting Repairs ................4-19 Required Maintenance ............................4-20 Scheduled Maintenance..........................4-20 Supplies Required for Inspection and Maintenance............................................4-20 5. Maintenance Procedure ..........................4-20 5-1. Cleaning...........................................4-20 5-2. Greasing ..........................................4-21 MECHANISM TROUBLESHOOTING GUIDE 1. Deck Mechanism.....................................4-23 2. Front Loading Mechanism.......................4-26 EXPLODED VIEWS 1. Front Loading Mechanism Section .........4-28 2. Moving Mechanism Section (1)...............4-29 3. Moving Mechanism Section (2)...............4-30 DECK MECHANISM PARTS LOCATIONS • Top View Procedure Starting No. 1 2 2 3 2 4 5 2 6 3 7 4 9 5 11 10 18 1 16 31 17 19 19 12 14 15 8 13 33 20, 21 • Bottom View 20 24 30 29 29 23 30 20 25 32 27 26 28 24 22 21 20,21,23, 24,25 20,21,23, 24,25,26 2,3,14,20, 21,25,23, 24,26 25 2,3,14,25, 29 2,3,14,25, 29 2,3,14 2,3,20,21, 22 T T T T T 1 Hook, Chassis Hole Chassis Hole 1 Hook Chassis Embossing Chassis Embossing 1 Screw 1 Hook 1 Hook 2 Hook A-2 A-2 A-2 A-3 A-3 A-3 A-4 A-4 A-4 A-4 T T T T T T T T T T Base Assembly P4 Opener Lid Arm Assembly Pinch Lever T/Up / Arm T/Up Chassis Embossing Chassis Embossing Shaft 1 Hook A-5 A-5 A-5 A-5 T T T T Belt Capstan/Motor Capstan Lever F/R Clutch Assembly D35 Brake Assembly Capstan Gear Drive/Gear Cam Gear Sector Plate Slider 3 Screw Locking Tab Washer Locking Tab Washer/Hook 1 Hook Shaft Guide A-6 A-6 A-6 A-6 A-7 A-7 A-7 B B B B B B B 27 Lever Tension 1 Hook A-7 B 28 Lever Spring Locking Tab A7 B 29 Gear Assembly P2/Gear Assembly P3 Boss 30 Base Assembly P2/Base Assembly P3 Chassis Slot A-8 A-8 B B 31 Base Loading 1 Screw A-9 T 32 Base Tension 33 Arm Assembly Idler Chassis Embossing Locking Tab A-9 A-9 B T 21 22 23 24 25 26 T:Top, B:Bottom NOTE : When reassembly perform the procedure in the reverse order. 1) When reassembling, confirm Mechanism and Mode Switch Alignment Position (Refer to Page 4-13) 2) When disassembling, the Parts for Starting No. Should be removed first. 4-1 Fig- Viure ew A-1 A-2 A-2 A-2 A-2 6 7 8 9 10 11 2,3 12 2,3 13 2,3 14 2,3,12,13, 15 14 16 17 17 18 17 19 17,18 20 Drum Assembly Plate Top Holder Assembly CST Opener Door Bracket Assembly L/D Motor Gear Assembly Rack F/L Arm Assembly F/L Lever Assembly S/W Arm Assembly Cleaner Head F/E Base Assembly A/C Head Brake Assembly T Brake Assembly RS Arm Assembly Tension Reel S/Reel T Fixing Type 3 Screw 2 Hook Chassis Hole Chassis Hole 3 Hook 2,3,4 2,3,4,6 15 Part DECK MECHANISM DISASSEMBLY Stator (S2) (S2) (S3) Drum Motor (S3) Rotor Drum Sub Assembly (Fig. A-1-1) (A) Drum FPC Carbon Brush (S1) (S1) (S1) H2 H1 Holder FPC Fig. A-1 (Fig. B-1) 1. Drum Assembly (Fig. A-1-1) 1) Unplug the Drum FPC Connector. 2) Remove three Screws(S1) on bottom side and separate the Drum assembly. 3) Unhook (H1), (H2) and separate the Holder FPC and Cap FPC. Cap FPC 1-1. Drum Motor 1) Remove two Screws(S2) and disassemble the Stator of the Drum Motor. 2) Remove two Screws(S3) and separate the Rotor of the Drum Motor from the Drum Sub assembly. Drum FPC Holder FPC NOTE When reassembling, confirm (A) portion of the Drum Sub assembly whether the Carbon Brush is in there or not. 4-2 Figure in the opposite direction DECK MECHANISM DISASSEMBLY Plate Top (Fig. A-2-1) (C) (B') (B) Holder Assembly CST (Fig. A-2-2) (E) Arm Assembly F/L (Fig. A-2-6) Lever Assembly S/W (Fig. A-2-7) (H8) (C1) Bracket Assembly L/D Motor Spring Lever S/W (Fig. A-2-4) (C') (D) (E') Opener Door (Fig. A-2-3) (H6) Chassis (A) Gear Assembly Rack F/L (Fig. A-2-5) Fig. A-2 4-3 (B) DECK MECHANISM DISASSEMBLY 2. Plate Top (Fig. A-2-1) 1) Pull the (B) portion of the Plate Top back in direction of arrow and separate the right side of it. 2) pull the (B’) portion of the Plate Top back in direction of arrow and separate the left side of it. (Used tools : (-) type driver, anything tool with sharp point or flat point.) 2) Unhook three Hooks(H3, H4, H5) on bottom side of the Chassis, lift up the Bracket Assembly L/M and disassemble the Bracket Assembly L/D Motor. (H4) Bracket assembly L/M (H3) NOTE (1) When reassembling, push the Plate Top after alignment the two position(C), (C’) as below Fig. 6. Gear Assembly Rack F/L (Fig. A-2-5) (C') 1) Move the Gear Assembly Rack F/L in direction of arrow(A) and unhook the Hook(H6) pulling back in front. 2) Separate the Gear Rack F/L in direction of arrow(B). (C) (B') (H5) (B) NOTE When reassembling, align the gear part of the Gear Assembly Rack F/L with the Gear Drive as below Fig. Gear Rack F/L 3. Holder Assembly CST (Fig.A-2-2) 1) Move the Holder Assembly CST in direction of arrow and separate the left side of it first through the (D) position of the Chassis. Holder assembly CST Chassis Gear Drive 7. Arm Assembly F/L (Fig. A-2-6) (D) 1) Move the Arm Assembly F/L in direction of arrow and separate the left side of it first. 2) Disassemble the Arm Assembly F/L from each guided hole of the Chassis. 2) Disassemble the right side of the Holder Assembly CST from each guided hole of the Chassis. NOTE 8. Lever Assembly S/W(Fig. A-2-7) 1) Unhook the Hook(H8) in the left side of the Chassis and remove the Lever Assembly S/W. When reassembling, insert the (E) part of the Holder Assembly CST in the (E’) hole of the Chassis first and assemble the left side of it. Chassis 4. Opener Door (Figure. A-2-3) 1) Turn the Opener Door clockwise and remove it through the guide hole of the Chassis. 5. Bracket Assembly L/D Motor (Fig. A-2-4) 1) Unplug the Connector(C1). 4-4 (H8) DECK MECHANISM DISASSEMBLY Arm Assembly Cleaner (Fig. A-3-1) (A) (S4) Base Assembly A/C Head (A) (Fig. A-3-3) Head F/E (Fig. A-3-2) Chassis Fig. A-3 9. Arm Assembly Cleaner (Fig. A-3-1) 11. Base Assembly A/C Head (Fig. A-3-3) 1) Breakaway the (A) portion as Fig. A-3-1 from the embossing of the Chassis, turn the Arm assembly Cleaner to clockwise direction and lift it up. 1) Remove the Screw(S4) and lift the Base Assembly A/C Head up. 10. Head F/E (Fig. A-3-2) 1) Breakaway the (A) portion of the Head F/E from the embossing of the Chassis, turn it to counterclockwise direction and lift it up. 4-5 DECK MECHANISM DISASSEMBLY Arm Assembly Tension (Fig. A-4-3) (H11) Spring TB Brake Assembly T (Fig. A-4-1) Spring Tension Reel S Reel T (Fig. A-4-4) (Fig. A-4-4) Spring RS Brake Assembly RS (Fig. A-4-2) (H12) (H9) (H10) Base Tension Chassis Fig. A-4 12. Brake Assembly T (Fig. A-4-1) NOTE 1) Unhook the Spring TB from the Hook(H9) of the Chassis. 2) Lift the Brake Assembly T up. Difference for Springs Spring TB Spring RS Color (Black) Spring Tension 13. Brake Assembly RS (Fig. A-4-2) 1) Unhook the Spring RS from the Hook(H10) of the Chassis. 2) Lift the Brake Assembly T up. 15. Reel S / Reel T (Fig. A-4-4) 1) Difference for Reel S / Reel T 14. Arm Assembly Tension (Fig. A-4-3) 1) Unhook the Spring Tension from the Hook(H11) of the Arm Assembly Tension. 2) Unhook the Hook(H12) of the Base Tension and lift the Arm Assembly Tension up. Reel S 4-6 Reel T DECK MECHANISM DISASSEMBLY Opener Lid (Fig. A-5-2) (B) (B) Arm Assembly Pinch (Fig. A-5-3) (C) Base Assembly P4 Lever T/up (Fig. A-5-1) (Fig. A-5-4) (H13) (C) Arm T/up (H13) (Fig. A-5-5) (A) Chassis Fig. A-5 16. Base Assembly P4 (Fig. A-5-1) NOTE 1) Breakaway the (A) portion of the Base Assembly P4 from the embossing of the Chassis. 2) Turn the Base Assembly P4 to counterclockwise direction and lift it up. When reassembling, confirm the (C) portion of the Arm Assembly Pinch is inserted to the Chassis hole correctly as Fig. 17. Opener Lid (Fig. A-5-2) 19. Lever T/up (Fig. A-5-4)/ Arm T/up (Fig. A-5-5) 1) Breakaway the (B) portion of the Opener Lid from the embossing of the Chassis. 2) Turn the Opener Lid to clockwise direction and lift it up. 1) Unhook the Hook(H13) of the bottom Chassis and lift the Lever T/up up. 2) Lift the Arm T/up up. 18. Arm Assembly Pinch (Fig. A-5-3) 1) Lift the Arm Assembly Pinch up. 4-7 DECK MECHANISM DISASSEMBLY Belt Capstan (Fig. A-6-1) Motor Capstan (Fig. A-6-2) Washer(W1) Clutch Assembly D35 (Fig. A-6-4) (L1) (L1) Brake Assembly Capstan (Fig. A-6-5) Lever F/R (Fig. A-6-3) (L2) Chassis (S5) Fig. A-6 22. Clutch Assembly D35 (Fig. A-6-4) 20. Belt Capstan (Fig. A-6-1)/ Motor Capstan (Fig. A-6-2) 1) Remove the Belt Capstan. 2) Remove the three Screws(S5) on bottom Chassis and lift the Motor Capstan up. 21. Lever F/R (Fig. A-6-3) 1) Unlock the Locking Tab(L1) as Fig. A-6-3 and lift the Lever F/R up. 1) Remove the Washer(W1) and lift the Clutch Assembly D35 up. 23. Brake Assembly Capstan (Fig. A-6-5) 1) Pull the Locking Tab(L2) back in direction of arrow and lift it up. 4-8 DECK MECHANISM DISASSEMBLY (H14) Gear Cam Hole(B) Gear Drive Hole(A) Gear Cam (Fig. A-7-2) Gear Sector Washer (W2) (Fig. A-7-3) Plate Slider Gear Drive (Fig. A-7-4) (Fig. A-7-1) (A) Lever Tension (Fig. A-7-5) Lever spring (L3) (Fig. A-7-6) Gear Drive Hole(C) Base Loading (H15) (H16) Chassis Fig. A-7 24. Gear Drive (Fig. A-7-1)/ Gear Cam (Fig. A-7-2) 26. Plate Slider (Fig. A-7-4) 1) Just lift the Plate Slider up. 1) Remove the Washer(W2) and lift the Gear Drive up. 2) Unhook the Hook(H14) of the Gear Cam and lift the Gear Cam up. NOTE When reassembling, align the Gear Drive Hole(A) and the Gear Cam Hole(B) in a straight line after the Gear Drive Hole(C) is aligned with the Chassis Hole as Fig. 27. Lever Tension (Fig. A-7-5) 1) Unhook the (A) portion of the Lever Tension from the Hook(H16) of the Chassis. 2) Turn the Lever Tension to counterclockwise direction and lift it up. 28. Lever Spring (Fig. A-7-6) 1) Unlock the Locking Tab(L3) of the bottom Chassis and lift the Lever Spring up. 25. Gear Sector (Fig. A-7-3) 1) Unhook the Hook(H15) of the Base Loading on bottom Chassis and lift the Gear Sector up. 4-9 DECK MECHANISM DISASSEMBLY Gear Assembly P2 Hole Gear Assembly P3 Hole Gear Assembly P3 (Fig. A-8-2) Lever Spring Boss Gear Sector Hole(A) Gear Assembly P2 Plate Slider Hole(B) (Fig. A-8-1) (B) (A) Chassis Base Assembly P3 (Fig. A-8-4) Base Assembly P2 Fig. A-8 (Fig. A-8-3) 29. Gear Assembly P2 (Fig. A-8-1)/ Gear Assembly P3 (Fig. A-8-2) 30. Base Assembly P2 (Fig. A-8-3)/ Base Assembly P3 (Fig. A-8-4) 1) Just lift the Gear Assembly P2 up. 2) Just lift the Gear Assembly P3 up. 1) Move the Base Assembly P2 in direction of arrow(A) along the guide hole of the Chassis and disassemble it on bottom side. 2) Move the Base Assembly P3 in direction of arrow(B) along the guide hole of the Chassis and disassemble it on bottom side. NOTE When reassembling, align the two holes of the Gear Assembly P2 and P3 in a straight line after confirmation whether the Gear Sector Hole(A) and the Plate Slider Hole(B) are aligned or not as Fig. 4-10 DECK MECHANISM DISASSEMBLY Base Tension (S7) Base Loading (Fig. A-9-2) Arm Assembly Idler (Fig. A-9-1) (A) (B) (Fig. A-9-3) (C) (D) Chassis Fig. A-9 31. Base Loading (Fig. A-9-1) 33. Arm Assembly Idler (Fig. A-9-3) 1) Remove the Screw(S7). 2) Lift the Base Loading up. 1) Make narrower the two parts, (B) and (C), as Fig. A-9-3. 2) Lift the Arm assembly Idler up. 32. Base Tension (Fig. A-9-2) NOTE 1) Breakaway the (A) portion of the Base Tension from the embossing of the Chassis. 2) Turn the Base Tension to counterclockwise direction and lift it up. When disassembling, be careful not to be caught the (D) part by the Chassis as Fig. 4-11 DECK MECHANISM ADJUSTMENT • Tools and Fixfures for Service SR K 1. Cassette Torque Meter 1. SRK-VHT-303(Not SVC part) 1. Parts No: D00-D006 -V HT -S 2. Alignment Tape Parts No NTSC: DTN-001 PAL:DTN-0002 3. Torque Gauge 3. 600g.Cm ATG 3. Parts No:D00-D002 5. Post Height Adjusting Driver Parts No:DTL-0005 6. + Type Driver (ø 5) 300 250 200 150 0 50 SR VID K CAS EO S TOR ETTE Q MET UE VHT ER -303 -T K- V HT0 SR 50 100 150 200 300 250 4. Torque Gauge Adaptor Parts No:D09-R001 4-12 DECK MECHANISM ADJUSTMENT 1. Mechanism Alignment Position Check Purpose:To determine if the Mechanism is in the correct position, when a Tape is ejected. Test Equipment/ Fixture Test Conditions (Mechanism Condition) • Blank tape • Eject Mode (with Cassette ejected) 1) Turn the Power S/W on and eject the Cassette by pressing the Eject Button. 2) Remove the Top Cover and Plate Assembly Top, visually check if the Gear Cam Hole is aligned with the Chassis Hole as below Fig. C-2. 3) IF not, rotate the Shaft of the Loading Motor to either clockwise or counterclockwise until the alignment is as below Fig. C-2. Check Point • Mechanism and Mode Switch Position 4) Remove the Screw which fixes the Deck Mechanism and Main Frame and confirm if the Gear Cam is aligned with the Gear Drive as below Fig. C-1(A). 5) Confirm if the Mode S/W on the Main P.C.Board is aligned as below Fig. C-1(B). 6) Remount the Deck Mechanism on the Main P.C.Board and check each operation. CHECK DIAGRAM Gear Cam (A) Mode S/W (B) Gear Drive Gear Cam (o) and Gear Drive (o) groove alignment BOTTOM VIEW Fig. C-1 L/D Motor Assembly Gear Cam (B) (A') (A) (B') Chassis Hole TOP VIEW Fig. C-2 4-13 Gear Cam Hole Gear Drive Hole DECK MECHANISM ADJUSTMENT cassette without tape. Cover the holes of the End Sensors at the both sides of the Chassis to prevent a light leak. Then the Deck Mechanism drives to the Stop Mode. In this case, the Deck Mechanism can accept inputs of each mode, however the Rewind and Review operation can not be performed for more than a few seconds because the Take-up Reel Table is in the Stop State and can not be detected the Reel Pulses. 2. Preparation for Adjustment (To set the Deck Mechanism of the loading state without inserting a cassette tape). 1) 2) 3) 4) Unplug the power cord from the AC outlet. Disassemble the Top Cover and Plate Assembly Top. Plug the power cord into the AC outlet. Turn the power S/W on and push the Lever Stopper of the Holder Assembly CST to the back for loading the 3. Checking Torque Purpose: To insure smooth transport of the tape during each mode of operation. If the tape transport is abnormal, then check the torque as indicated by the chart below. Test Conditions (Mechanism Condition) Test Equipment/ Fixture • Torque Gauge(600g/cm ATG) • Torque Gauge Adaptor • Cassette Torque Meter SRK-VHT-303 • Play (FF) or Review (REW) Mode • Perform each Deck Mechanism mode without inserting a cassette tape(Refer to above No.2 Preparation for Adjustment). • Read the measurement of the Take-up or Supply Reels on the Cassette Torque Meter(Fig. C-3-2). • Attach the Torque Gauge Adaptor to the Torque Gauge and then read the value of it(Fig. C-3-1). Mode Item Checking Method Test Equipment Measurement Reel Measurement Values Fast Forward Torque Fast Forward Cassette Torque Gauge Rewind Torque Rewind Cassette Torque Gauge Supply Reel More than 400g/cm Play Take-Up Torque Play Cassette Torque Meter Take-Up Reel 40~100g/cm Review Torque Review Cassette Torque Meter Supply Reel 120~210g/cm Take-Up Reel More than 400g/cm NOTE: NOTE: The values are measured by using a Torque Gauge and Torque Gauge Adaptor with the Torque Gauge affixed. The torque reading to measure occurs when the tape abruptly changes direction from Fast Forward to Rewind Mode, when quick braking is applied to both Reels. • Torque Gauge (600g.cm ATG) • Cassette Torque Meter (SRK-VHT-303) SR K Torque Gauge -V HT -S 300 250 200 150 SR K 0 50 Torque Gauge Adaptor VID CAS EO S TOR ETTE Q MET UE VHT ER -303 -T K- V HT0 SR 50 100 150 200 300 Reel Table Fig. C-3-1 Fig. C-3-2 4-14 250 DECK MECHANISM ADJUSTMENT 4.Guide Roller Height Adjustment Purpose: To regulate the height of the tape so that the bottom of the tape runs along the tape guide line on the Lower Drum. 4-1. Preliminary Adjustment Test Equipment/ Fixture • Post Height Adjusting Driver Test Conditions (Mechanism Condition) • Play or Review Mode Adjustment Procedure Adjustment Point • Guide Roller Height Adjustment screws on the Supply and Take-Up Guide Rollers. ADJUSTMENT DIAGRAM 1) Confirm if the tape runs along the tape guide line of the Lower Drum. 2) If the tape runs the bottom of the guide line, turn the Guide Roller Height Adjustment Screw to clockwise direction. 3) If it runs the top, turn to counterclockwise direction. 4) Adjust the height of the Guide Roller to be guided to the guide line of the Lower Drum from the starting and ending point of the Drum. Guide Roller Height Adjustment screw Upper Flange Guide Roller Retaining Screw Fig. C-4-1 4-2. Precise Adjustment Test Equipment/Fixture • Oscilloscope • Alignment Tape • Post Height Adjusting Driver Adjustment Point Test Equipment Connection Points Test Conditions VCR(VCP) State • Guide Roller Height Adjustment Screws • Play an Alignment Tape • CH-1:PB RF Envelope • CH-2:NTSC: SW 30Hz PAL: SW 25Hz • Head Switching Output Point • RF Envelope Output Point Waveform Diagrams P2 POST ADJUSTMENT Adjustment Procedure 1) Play an Alignment Tape after connecting the probe of the Oscilloscope to the RF Envelope Output Test Point and Head Switching Output Test Point. 2) Tracking Control(in PB Mode) : Center Position(When this adjustment is performed after the Drum Assembly has been replaced, set the Tracking Control so that the RF Output is Maximum). 3) Height Adjustment Screw : Flatten the RF waveform. (Fig. C-4-2) 4) Turn(Move) the Tracking Control(in PB Mode) clockwise and counterclockwise.(Fig. C-4-3) 5) Check that any drop of RF Output is uniform at the start and end of the waveform. Turn the Roller Guide Height Adjustment Screw slightly to flatten the waveform. P3 POST ADJUSTMENT Fig. C-4-2 Tracking Control at center Turn(Move) the Tracking Control to both directions Fig. C-4-3 Connection Diagram NOTE OSCILLOSCOPE If the adjustment is excessive or insufficient the tape will jam or fold. RF ENVELOPE OUTPUT TEST POINT HEAD SWITCHING OUTPUT TEST POINT 4-15 DECK MECHANISM ADJUSTMENT 5. Audio/Control (A/C) Head Adjustment Purpose: To insure that the tape passes accurately over the Audio and Control Tracks in exact alignment of the both Record and Playback Modes. 5-1. Preliminary Adjustment (Height and Tilt Adjustment) Perform the Preliminary Adjustment, when there is no Audio Output Signal with the Alignment Tape. Test Equipment/ Fixture • Blank Tape • Screw Driver(+) Type 5mm Test Conditions (Mechanism Condition) Adjustment Point • Tilt Adjustment Screw(C) • Height Adjustment Screw(B) • Azimuth Adjustment Screw(A) • Play the blank tape Adjustment Procedure/Diagrams 1) Initially adjust the Base Assembly A/C Head as shown Fig. C-5-1 by using the Height Adjustment Screw(B). 2) Play a blank tape and observe if the tape passes accurately over the A/C Head without tape curling or folding. 3) If folding or curling is occured then adjust the Tilt Adjustment Screw(C) while the tape is running to resemble Fig. C-5-3. 4) Reconfirm the tape path after Playback about 4~5 seconds. NOTE Ideal A/C head height occurs when the tape runs between 0.2~0.25mm above the bottom edge of the A/C Head core. Tape A/C Head P4 10.9 Tape 0.2~0.25mm A/C Head Base Fig. C-5-3 Fig. C-5-1 X-Value Adjustment Hole Fixed Screw Azimuth Adjustment Screw(A) Tilt Adjustment Screw(C) Height Adjustment Screw(B) A/C Head Assembly Fig. C-5-2 4-16 DECK MECHANISM ADJUSTMENT (2) If folding or curling is observed at the top of it then slowly turn the Tilt Adjustment Screw(C) in the counterclockwise direction. 5-2. Confirm that the tape passes smoothly between the Take-up Guide and Pinch Roller(using a mirror or the naked eye). 1) After completing Step 5-1.(Preliminary Adjustment), check that the tape passes around the Take-up Guide and Pinch Roller without folding or curling at the top or bottom. (1) If folding or curling is observed at the bottom of the Take-up Guide then slowly turn the Tilt Adjustment Screw(C) in the clockwise direction. NOTE: Check the RF envelope after adjusting the A/C Head, if the RF waveform differs from Fig. C-5-4, performs Precise Adjustment to flat the RF waveform. 5-3. Precise Adjustment (Azimuth adjustment) • Oscilloscope • Alignment Tape(SP) • Screw Driver(+) Type 5mm Test Conditions (Mechanism Condition) Connection Point Test Equipment/ Fixture • Play an Alignment Tape 1KHz, 7KHz Sections • Audio output jack Adjustment Procedure Adjustment Point • Azimuth Adjustment Screw(A) • Height Adjustment Screw(B) 1KHZ 1) Connect the probe of the oscilloscope to Audio Output Jack. 2) Alternately adjust the Azimuth Adjustment Screw(A) and the Tilt Adjustment Screw(C) for maximum output of the 1KHz and 7KHz segments, while maintaining the flattest envelope differential between the two frequencies. 7KHZ A:Maximum B:Maximum Fig. C-5-4 6. X-Value Adjustment Purpose: To obtain compatibility with the other VCR(VCP) Models. Test Equipment/ Fixture • Oscilloscope • Alignment Tape(SP only) • Screw Driver(+) Type 5mm Test Conditions (Mechanism Condition) Connection Point Adjustment Point • Play an Alignment Tape • CH-1: PB RF Envelope • CH-2: NTSC: SW 30Hz PAL: SW 25Hz • Head Switching Output Test Point • RF Envelope Output Test Point Left Groove at the Base A/C Right Adjustment Procedure Adjustment Diagram X-Value Adjustment Hole 1) Release the Automatic Tracking to run long enough for tracking to complete it’s cycle. 2) Loosen the Fixed Mounting Screw and move the Base Assembly A/C Head in the direction as shown in the diagram to find the center of the peak that allows for the maximum waveform envelope. This method should allow the 31µm Head to be centrally located over the 58µm tape track. 3) Tighten the Base Assembly A/C Head mounting Screw. Fixed Screw Azimuth Adjustment Screw(A) Tilt Adjustment Screw(C) Height Adjustment Screw(B) OSCILLOSCOPE Connection Diagram RF ENVELOPE OUTPUT TEST POINT CH-1 CH-2 HEAD SWITCHING OUTPUT TEST POINT 4-17 DECK MECHANISM ADJUSTMENT 7. Adjustment after Replacing Drum Assembly (Video Heads) Purpose: To correct for shift in the Roller Guide and X value after replacing the Drum. Test Equipment/ Fixture Test Conditions (Mechanism Condition) Connection Point • CH-1: PB RF Envelope • Oscilloscope • Play the Blank Tape • CH-2: NTSC: SW 30Hz • Alignment Tapes • Play an Alignment Tape PAL: SW 25Hz • Blank Tape • Post Height Adjusting Driver • Head Switching Output Test Point • Screw Driver(+) Type 5mm • RF Envelope Output Test Point Checking/Adjustment Procedure Adjustment Points • Guide Roller Precise Adjustment • Switching Point • Tracking Preset • X-Value Connection Diagram OSCILLOSCOPE Play a blank tape and check for tape curling or creasing around the Roller Guide. If there is a problem then follow the procedure RF ENVELOPE OUTPUT TEST POINT 4. "Guide Roller Height" and 5. "Audio Control(A/C) Head HEAD SWITCHING OUTPUT TEST Adjustment". CH1 CH2 POINT Waveform V1/V MAX E 0.7 V2/V MAX E 0.8 RF ENVELOPE OUTPUT V1 V V2 Fig. C-7 8. Check the Tape Travel after Reassembling Deck Assembly. 8-1. Checking Audio and RF Locking Time during playback and after CUE or REV (FF/REW) • Oscilloscope • Alignment Tapes(with 6H 3KHz Color Bar Signal) • Stop Watch Test Equipment Connection Connection Points Points Specification Test Equipment/ Fixture • RF Locking Time: Less than 5 sec. • Audio Locking Time:Less than 10sec • CH-1: PB RF Envelope • CH-2: Audio Output • RF Envelope Output Point • Audio Output Jack Test Conditions (Mechanism Condition) • Play an Alignment Tape (with 6H 3kHz Color Bar Signal) Checking Procedure NOTES: Play an Alignment Tape then change the operating mode to CUE or REV and confirm if the unit meets the above listed specifications. 1) CUE is the forward search mode 2) REV is the backward search mode 3) Refer to the Play mede 8-2. Checking for tape curling or jamming Test Equipment/ Fixture • T-160 Tape • T-120 Tape Specification Test Conditions VCR(VCP) (Mechanism State Condition) • Be sure there is no tape jamming or curling at • Run the CUE, REV, Play mode at the the begining, middle or end of the tape. beginning and the end of the tape. Checking Procedure 1) Confirm that the tape runs smoothly around the roller guides, Drum and A/C Head Assemblies while abruptly changing operating modes from Play to CUE or REV. This is to be checked at the begining, middle and end sections of the tape. 2) Confirm that the tape passes over the A/C Head Assembly as indicated by proper audio reproduction and proper tape counter performance. 4-18 MAINTENANCE/INSPECTION PROCEDURE 1. Check before starting repairs The following faults can be remedied by cleaning and oiling. Check the needed lubrication and the conditions of cleanliness in the unit. Check with the customer to find out how often the unit is used, and then determine that the unit is ready for inspection and maintenance. Check the following parts. Phenomenon Replacement Inspection Color beats Dirt on Full-Erase Head Poor S/N, no color F/E Head o Dirt on Video Head o Vertical or Horizontal jitter Dirt on Video Head Dirt on tape transport system o Low volume, Sound distorted Dirt on Audio/Control Head o Dirt on Pinch Roller o Belt Capston Clutch Assembly D35 torque reduced o Clutch Assembly D35 Tape does not run. Tape is slack In Review and Unloading (off mode), the tape is rolled up loosely. Video Head Fig. C-9-1 Top View A/C Head Pinch Roller Cleaning Drum and transport system Fig. C-9-3 NOTE If locations marked with o do not operate normally after cleaning, check for wear and replace. See the EXPLODED VIEWS at the end of this manual as well as the above illustrations and see the Greasing (Page 4-21, 22) for the sections to be lubricated and greased. Fig. C-9-2 Bottom View * No. (1)~(12) Indicates the Tape Path to be traveled from Supply Reel to Take-up Reel. (6) Base Assembly P3 (3) F/E Head (7) A/C Head (8) P4 Post (5) Drum Assembly (Video Head) (10) Pinch Roller (11) Take-up Guide Post (4) Base Assembly P2 (2) Tension Post (9) Capstan Shaft (1) Supply Reel (12) Take-up Reel Fig. C-9-3 Tape Transport System 4-19 MAINTENANCE/INSPECTION PROCEDURE 2. Required Maintenance The recording density of a VCR(VCP) is much higher than that of an audio tape recorder. VCR(VCP) components must be very precise, at tolerances of 1/1000mm, to ensure compatibility with the other VCRs. If any of these components are worn or dirty, the symptoms will be the same as if the part is defective. To ensure a good picture, periodic inspection and maintenance, including replacement of worn out parts and lubrication, is necessary. Schedules for maintenance and inspection are not fixed because they vary greatly according to the way in which the customer uses the VCR(VCP), and the environment in which the VCR(VCP) is used. But, in general home use, a good picture will be maintained if inspection and maintenance is made every 1,000 hours. The table below shows the relation between time used and inspection period. Table 1 About 1 year About 18 months (1) (2) (3) (4) Grease : Kanto G-311G (Blue) or equivalent Isopropyl Alcohol or equivalent Cleaning Patches Grease : Kanto G-381(Yellow) 5. Maintenance Procedure 5-1) Cleaning 3. Scheduled Maintenance When inspection is necessary 4. Supplies Required for Inspection and Maintence About 3 years Average hours used per day One hour (1) Cleaning video head First use a cleaning tape. If the dirt on the head is too stubborn to remove by tape, use the cleaning patch. Coat the cleaning patch with Isopropyl Alcohol. Touch the cleaning patch to the head tip and gently turn the head(rotating cylinder) right and left. (Do not move the cleaning patch vertically. Make sure that only the buckskin on the cleaning patch comes into contact with the head. Otherwise, the head may be damaged.) Thoroughly dry the head. Then run the test tape. If lsopropyl Alcohol remains on the video head, the tape may be damaged when it comes into contact with the head surface. (2) Clean the tape transport system and drive system, etc, by wiping with a cleaning patch wetted with Isopropyl Alcohol. NOTES: 1 It is the tape transport system which comes into contact with the running tape. The drive system consists of those parts which moves the tape. 2 Make sure that during cleaning you do not touch the tape transport system with excessive force that would cause deformation or damage to the system. Two hours Three hours Drum (Rotating Cylinder) Cleaning Patch Head Tip Coat With Isopropyl Alcohol Touch this section of cleaning patch to the head tip and gently turn the Drum (Rotating Cylinder) Fig. C-9-4 4-20 MAINTENANCE/INSPECTION PROCEDURE 5-2) Greasing (1) Greasing guidelines Apply grease, with a cleaning patch. Do not use excessive grease. It may come into contact with the tape transport or drive system. Wipe excessive grease and clean with cleaning patch wetted in Isopropyl Alcohol. (2) Periodic greasing Grease specified locations every 5,000 hours. 1) 2) 3) 4) 5) Loading Path Inside & Top side Base Assembly P2,P3 stopper Shaft Shaft Clutch Assembly D35 Shaft NOTE:Greasing Points 1) Loading Path Inside & Top side 2) Base Assembly P2, P3 stopper 3) Shaft 4) L/D Motor Gear Wheel Part 6) Plate Slider Guide Sections 7) Plate Slider Guide Sections 8) Gear Assembly P2, P2 Rubbing Sections 2 5) Arm Take-up Rubbing Sections 6)Reel S,T shaft(G381:Yellow) 7) Arm Assembly F/L Rotating Sections 1 2 3 4 1 8 3 4 5 7 6 Slider Guide 5 Slider Guide Chassis (Bottom) 7 7 6 Chassis (Top) Gear Part Gear Cam Gear Sector Gear Rack F/L Gear Drive Base Loading Guide Rail Chassis (Left Side) Chassis (Right Side) Plate Slider 4-21 MAINTENANCE/INSPECTION PROCEDURE Lever, F/R, Base, Tension GEAR AY, P2 & P3 Lever, F/R Boss Base, Tension Clutch (G-754. Yellow) Arm Tension Guide Hole 4-22 Cam MECHANISM TROUBLESHOOTING GUIDE 1.Deck Mechanism A. Auto REW doesn't work. YES Is the output of END sensor of supply side "H"? “H”: more than 3.5V “L”: less than 0.7V~1V YES NO Is the Vcc. voltage of End sensor 5V? NO Check the syscon power. YES Replace the End sensor. Is the voltage across IR LED between 0.8~1.5V? NO Replace the IR LED. YES Check the syscon circuit. B. No F/R modes. YES Is the present mode F/R Mode? NO Is the mode SW assembled correctly? (refer to page 4-13.) YES NO Does the Capstan Motor rotate? YES Do the T/Up, Supply Reel rotate? YES Check the syscon circuit. Is the normal voltage supplied to the Capstan Motor Vcc1, Vcc2? YES Does terminal voltage(Vctl) of Capstan Motor supply side more than 4V? YES Replace the Capstan Motor. 4-23 NO Check the servo, power circuits. MECHANISM TROUBLESHOOTING GUIDE C. AUTO STOP. (PLAY/CUE/REV) Check alignment positions (page 4-13). In Play/Cue/Rev, Is the Pinch Roller in contact with the Capstan Shaft? NO Is the output of DFG, DPG OK? YES Are there T/up and Supply Reel pulses. Replace the Drum Motor. NO YES NO Check the Servo, Syscon. YES Check the Syscon, µ-COM. Replace the Reel Sensor. D. Cassette doesn’t load. Insert the cassette. YES Does the Lever Assembly S/W work normally? NO Check Lever Assembly S/W. YES Is there variation for CST IN S/W Output? (In Tape with REC Tab “L”→“H”→“L”) (In Tape without REC Tab “L”→“H”→“L”→“H”) NO Does the CST IN S/W work normally? YES YES NO Check the Syscon Circuit. Check the Syscon Circuit. 4-24 NO Replace the CST IN S/W. MECHANISM TROUBLESHOOTING GUIDE E. In PB mode Tape Presence not sensed. Is the Pinch Roller attached to the Capstan Motor Shaft? NO Check Alignment positions (page 4-13). YES NO Does the T/Up Reel turn? NO Is the Belt ok? YES Replace the Belt. YES Check the Clutch and Idler Assembly. Does the Capstan Motor turn? YES Does the Drum Motor turn? NO YES Is the voltage supplied to the Capstan Motor Vcc1,Vcc2 each? YES Is the terminal voltage(vctl) of Capstan Motor supplied more than 4V? Are there DPG, DFG pulses? YES NO Check the Servo, Power. YES Are the T/Up and Supply Reel Sensors ok? Replace the Capstan Motor. YES NO Check the Servo, Syscon. Is the Vcc voltage of the Drum Motor normal? NO Check the Syscon, Circuit. YES Is the terminal voltage(vctl) of the Drum Motor more than 4V? YES Replace the Drum Motor. 4-25 NO Check the Syscon, Circuit. MECHANISM TROUBLESHOOTING GUIDE 2. Front Loading Mechanism A. Cassette cannot be inserted. Does the Lever Assembly Switch work? NO Is the Lever Assembly Switch Spring damaged or omitted? YES YES Does the CST IN Switch work normally? Is the Vcc of Main P.C.Board 5V? NO Replace or add the Lever Assembly Switch Spring. NO Replace the CST IN Switch. YES Check the syscon circuit. NO YES Is the voltage between cassette switch and GND on Main P.C.Board 5V?? Check the power circuit. NO YES Check the Mode switch location and syscon circuit. Is there a short circuit between cassette switch and GND on main P.C.Board? NO YES Remove the short circuit part or Replace the main P.C.Board. Replace the CST IN Switch. B. Cassette does not eject. Does the L/D Motor rotate in reverse? NO Check the L/D Motor or Drive IC. YES Does the Lever Assembly Switch work? NO Replace the Lever Assembly Switch. YES NO Does the Arm Assembly F/L work normally? Replace the Arm Assembly F/L. YES NO Replace the Opener Door. Does the Opener Door work? 4-26 MECHANISM TROUBLESHOOTING GUIDE C. Cassette does not load. Does the cassette insert? YES Does the Opener Lid work? YES NO Does the Gear Assembly Rack F/L work? YES Replace the Opener Lid. NO Replace the Gear Rack F/L. Does the Opener Door work? YES NO Check the opener Door assembled correctly. Does the Arm Assembly F/L work? YES NO Does the L/D Motor work? YES Replace the Arm Assembly F/L. NO Does the Holder Assembly Cassette move the Arm Assembly F/L? YES Check the power of L/D Motor. NO Replace the Front Loading Mechanism Assembly. Check the Holder Assembly Cassette assembled correctly. 4-27 EXPLODED VIEWS 1. Front Loading Mechanism Section 103 117 A24 100A 110 105 116 115 117 106 112 107 102 A21 100B 113 100 114 032 A23 054 054A A22 109 4-28 EXPLODED VIEWS 2. Moving Mechanism Section(1) OPTIONAL PART 031 079 011 402 002A 017 401 022 032 003 402 002 001 012 A01 024 008 004 405 023 406 006 A03 409 007 013 016 014 405 010 015 009 019 018 025 026 027 A04 029 028 020 030 021 4-29 EXPLODED VIEWS 3. Moving Mechanism Section(2) OPTIONAL PART 518 055 058 051 060 056 052A 052 517 A11 078 061 410 067 066 065 077 076 064 A12 032 068 069 070 4-30 SECTION 5. REPLACEMENT PARTS LIST NOTE: Warning Parts that are shaded are critical With respect to risk of fire or electrical shock. MODEL : NTH960N NSP : Not Service Part MECHANICAL SECTION S AL LOCA.NO PART NO. A00 A01 A04 A11 A12 A21 A22 A23 A24 6721R-0771U 6723R-D402G 4811R-0038B 4471R-0005A 4471R-0004A 4931R-0047A 4471R-0006A 4261R-0023A 4510R-0046A 001 002 002A 003 004 008 009 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 051 052 052A 054 054A 055 056 058 060 061 064 065 066 067 068 069 070 076 077 078 6723R-D305G 4680R-B008A 5202R00002C 4930R-0285A 5006R-0034A 6850R-HG18Z 4260R-0038A 4261R-0022A 3041R-0037A 3041R-0038A 3041R-0039A 5870R-0005A 3041R-0036A 4408R-0003A 4970R-0140A 4421R-0008A 4970R-0128A 4421R-0006A 6520D00002A 3040R-0057A 4261R-0024A 4810R-0111A 4680R-D006A 4470R-0093A 4408R-0004A 4261R-0019E 4510R-0043A 4970R-0123A 3141R-0040A 4400R-0005A 4680R-A012B 4980R-0023A 4470R-0100A 4970R-0124B 4470R-0097A 4470R-0096A 4421R-0007A 4510R-0040A 4265R-0005A 4470R-0098A 4261R-0021A 4970R-0122A 4470R-0095A 4470R-0094A 4970R-0122A 4261R-0020A 4510R-0047A 3300R-M116A 4510R-0041A RUN DATE : 2004.05.01 DESCRIPTION ASSEMBLY PARTS SECTION DECK ASSEMBLY,VIDEO DRUM(CIRC) ASSEMBLY BRACKET ASSEMBLY GEAR ASSY GEAR ASSY HOLDER ASSY GEAR ASSY ARM ASSY LEVER PARTS SECTION DRUM(CIRC) ASSEMBLY MOTOR(MECH) BRUSH,CARBON HOLDER CAP CABLE,FLAT ARM ARM ASSY BASE ASSY BASE ASSY BASE ASSY OPENER BASE ASSEMBLY REEL SPRING BRAKE ASSEMBLY SPRING BRAKE ASSY HEAD(CIRC) BASE ARM ASSEMBLY BRACKET MOTOR(MECH) GEAR REEL ARM ASSEMBLY LEVER SPRING CHASSIS ASSEMBLY BELT MOTOR(MECH) SUPPORTER GEAR SPRING GEAR GEAR BRAKE ASSY LEVER CLUTCH ASSEMBLY GEAR ARM ASSY SPRING GEAR GEAR SPRING ARM ASSY LEVER PLATE LEVER - 5-1 - SPECIFICATION DECK/MECHA D35 LG T/L (4HD(ALL DECK/MECHA (8N4T) D35-4CH NTSC L/D P3 P2 CST RACK F/L F/L ASSY SWITCH DECK/MECHA SUB D35-4CH NT (8N4 DRUM VH4302-800 SANYO FOR D35K ASSY D33 (TIP+2 SPRING) 1.4, FPCB(4CH) FPC P=1.25 FFC UL2896(0.05X0.8) 7 T/UP(D35) TENSION(D35) P2 P3 P4 LID(D35) A/C HEAD (ALPS) S COIL RS D35 RS COIL D35 (TB) T D35 FE ST FE HEAD LOADING IDLER (H) L/D LOADING RF-370CA-12560 MABUCHI DECK/MECHA WHEEL OTHER T DECK/MECHA PINCH T/UP COIL TENSION(D35) D35 CAPSTAN CAPSTAN MCVC-035TB LGIT FOR T/ CAPSTAN(D35) RACK F/L COIL D35 (RACK F/L) DRIVE(D35) CAM(D35) CAPSTAN F/R(D35) D35 (M) SECTOR(D35) P3 COIL D35 P3 P2 COIL D35 P2 SPRING SLIDER TENSION REMARKS MODEL : NTH960 S AL RUN DATE : 2004.05.01 LOCA.NO 079 100 102 103 105 106 107 109 110 112 113 114 115 116 117 116 117 PART NO. 3040R-0056A 3301R-M022A 4970R-0130A 4930R-0276A 4930R-0274A 4930R-0275A 4510R-0044A 5870R-0004A 4260R-0035A 3070R-0002A 4970R-0127A 4260R-0036A 4510R-0042A 4970R-0138A 3300R-M137A 4970R-0138A 3300R-M137A 402 405 406 409 410 452 517 518 1MPC0261418 1SZZR-0031B 1MEC0302018 1SZZR-0032B 1APF0262218 353-051A 1WZZR-0004D 1WZZR-0004A DESCRIPTION BASE PLATE ASSEMBLY SPRING HOLDER HOLDER HOLDER LEVER OPENER ARM BODY SPRING ARM LEVER SPRING PLATE SPRING PLATE SCREW SCREW MACHINE,PAN HEAD SCREW,DRAWING PAN HEAD MACHINE SCREW S/W + SCREW,DRAWING SCREW TAP TITE(B),PAN HEAD SCREW,DRAWING WASHER,DRAWING WASHER,DRAWING SPECIFICATION TENSION(D35) TOP COIL D35 (STOPPER) SIDE(L) CST SIDE(R) STOPPER DOOR F/L(L) F/L COIL D35 (F/L(R)) F/L(R) SWITCH COIL D35 SWITCH SPRING CST COIL D35 SWITCH SPRING CST REMARKS NSP D 2.6 L 4.0 MSWR3/FZY + 1 D2.6 L5.8 SWRCH16A/FZY TAP D 3.0 L 6.0 MSWR3/FZY + 1 D2.6 L5.0 SWRCH18A/FZY TAP #NAME? SPECIAL STOPPER STOPPER Cabinet & Main Frame Section S AL LOCA.NO. PART NO A00 A42 A43 A44 A45 6721R-0771U 6871RK5700K 05503807 3211RKS008B 3501RK3200B 250 260 277 278 280 281 283 284 285 286 300 320 323 325 330 3110R-S040F 3210R-0023A 4940R-Z075A 4940R-Z076B 3720R-F721D 524-013A 50502527 442-681A 4940R-Z086A 4940R-S017A 6410RZHV01A 50502166 3111R-0089B 4930R-0190B 3550R-0210A 452 457 462 353-051A 353-051E 353-136A DESCRIPTION ASSEMBLY SECTION DECK ASSEMBLY,VIDEO PWB(PCB) ASSEMBLY,C/SKD PANEL ASSEMBLY,FRONT FRAME ASSEMBLY BOARD ASSEMBLY PARTS SECTION CASE FRAME KNOB KNOB PANEL,VIDEO MAGNET DOOR SPRING KNOB KNOB POWER CORD PANEL CASE ASSY HOLDER ASSEMBLY COVER SCREW SCREW,DRAWING SCREW,DRAWING SCREW,DRAWING SPECIFICATION REMARKS DECK/MECHA D35 LG T/L (4HD(ALL SNILN4T3526 NTH960 C-TYPE VCR MAIN(S008B) + PACKING CCD TL-AT230 LV-TL1960 2960 MOLD AIRHALL BA VCR - MAIN SHUTTLE(TL-AR30M) CCD TL-AT130 MOLD CCD LV-TL1960 S MOLD HIPS 40AF VCR - ASSY DOOR HRV30C DOOR CCD LV-TL124 MOLD SLIDE (LV-TL24) IT10S2(6A/250V) VOLEX IMMETRO NTH960C PRE-AMP (PBSB-SH) LCD PWB(ABS XR-401)) BOTTOM(LARGE) SPECIAL SPECIAL (3X12) SPECIAL(FBK) (353S353A) Packing & Accessory Section S AL LOCA.NO. 801 802 803 804 808 900 PART NO 3835RS0069N 3890R-C065K 3920R-E016A 3858R-S001A 534-008C 6711R1P041H DESCRIPTION INSTRUCTION ASSEMBLY BOX,MASTER PACKING SHEET (MECH) BATTERY,MANGANESE REMOTE CONTROLLER ASSEMBLY - 5-2 - SPECIFICATION CCD TL-AT230M-AABBDL1_ENG_POR_ TL-AT130M AABBDL . 1 Packing LV-TL24I 0.02 0 EPS 10 Packing LDPE 600M 630MM 0.5 VC AAAM(R03) SEOTONG 1-5 V - 1PA P9 LV-TL1960 REMARKS MODEL : NTH960 Electrecal section S AL LOCA.NO. RUN DATE : 2004.05.01 PART NO RB500 534-059AAAA BZ501 RL301 6908RB0001A 6920R-B201A C101 C102 C103 C105 C106 C109 C111 C112 C113 C114 C116 C117 C118 C119 C120 C121 C123 C128 C152 C153 C154 C155 C170 C172 C173 C301 C302 C303 C304 C305 C306 C307 C308 C309 C310 C311 C312 C313 C314 C315 C316 C317 C318 C319 C322 C323 C324 C325 C326 C327 C328 C329 C330 C331 624-088F 624-088F 624-082C 0CQ1031Y519 624-087A 624-085D 0CN223AK948 0CG3320U630 0CG3310U510 0CQ4732K409 0CE108BF630 624-082H 0CE2276D638 624-085D 0CE477BH630 624-082G 0CE337BJ610 0CN223AK948 0CE1064F638 0CE1064F638 0CE1064F638 0CE4754K638 0CE1044K638 0CN1040K948 0CE4764J638 0CN1040K948 0CN1030F678 0CE1054K638 0CE2274C638 0CN1040K948 0CN1030F678 0CX2700K408 0CX3300K408 0CN3310K518 0CE4754K638 0CN1810K518 0CX2200K408 0CN1010K418 0CN1020K518 0CE1063F638 0CE1063F638 0CN1030F678 0CE2254K638 0CN1040K948 0CE4764F638 0CE4764F638 0CN1040K948 0CN1050K948 0CE1063F638 0CE1063F638 0CN223AK948 0CN223AK948 0CN1030F678 0CE2274C638 DESCRIPTION BATTERY,LITHIUM BATTERY,LITHIUM BUZZER BUZZER BUZZER CAPACITOR CAPACITOR,DRAWING CAPACITOR,DRAWING CAPACITOR,AL.ELECTROLYTIC CAPACITOR,FIXED FILM CAPACITOR CAPACITOR CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,SEMI CERAMIC CAPACITOR,FIXED CERAMIC(TEMP.C CAPACITOR,FIXED FILM CAPACITOR,FIXED ELECTROLYTIC CAPACITOR CAPACITOR,FIXED ELECTROLYTIC CAPACITOR CAPACITOR,AL.ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR,AL.ELECTROLYTIC CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(T.C) CAPACITOR TUBULA(T.C) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,FIXED TUBULAR(High d CAPACITOR TUBULA(T.C) CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,AL.ELECTROLYTIC CAPACITOR,AL.ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,AL.ELECTROLYTIC CAPACITOR,AL.ELECTROLYTIC CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC - 5-3 - SPECIFICATION LR6A-2S/ MATUSHITA - - LITHUM PKM24SP-3801 PKM24SP-3801 MURA UT205-5SC YUYU AC 250 V 5-0 A PCX2 275V 0.1UF,M (PILKO) PCX2 275V 0.1UF,M (PILKO) 100MF/400V SHL SMPS S/Y 0.01UF D 630V 10% PE NI TP5 HIGH-VOL 150P/1KV SMPS NEW-KOR CE 47UF/50V KME (SMPS) 0.022UF 50V Z F TA26 S 3300 PF 400V M E R(NK,AD,SD) 330PF D 400V 10% B(Y5P) R 0.047UF S 50V 5% PE TP5 1000UF KME 16V M FM5 BULK CE 1000UF/10V SHL(10*12.5)T/P 220M SMS 10V M FM5 TP(5) CE 47UF/50V KME (SMPS) 470UF KME TYPE 25V M FM5 BULK CE 470UF/25V SHL(10*12.5)T/P 330UF KME TYPE 35V 20% FL BULK 0.022UF 50V Z F TA26 S 10M SRA 16V M FM5 TP(5) 10M SRA 16V M FM5 TP(5) 10M SRA 16V M FM5 TP(5) 4.7UF SRA,SS 50V 20% FM5 TP 5 0.1M SRA 50V M FM5 TP(5) 0.1UF D 50V 80%,-20% F(Y5V) TA 47UF SRA,SS 35V M FM5 TP 5 0.1UF D 50V 80%,-20% F(Y5V) TA 0.01M 16V M Y TA26 1.0M SRA/SS50V M FM5 TP(5) 220M SRA 6.3V M FM5 TP(5) 0.1UF D 50V 80%,-20% F(Y5V) TA 0.01M 16V M Y TA26 27P 50V J SL TA26 33P 50V J SL TA26 330P 50V K B TA26 4.7UF SRA,SS 50V 20% FM5 TP 5 180P 50V K B TA26 22P 50V J SL TP26 100PF 50V J B TA26 1000P 50V K B TA26 10M SRE/SE 16V M FM5 TP(5) 10M SRE/SE 16V M FM5 TP(5) 0.01M 16V M Y TA26 2.2UF SRA,SS 50V 20% FM5 TP 5 0.1UF D 50V 80%,-20% F(Y5V) TA 47M SRA/SS 16V M FM5 TP(5) 47M SRA/SS 16V M FM5 TP(5) 0.1UF D 50V 80%,-20% F(Y5V) TA 1UF 50V Z F TA26 D 10M SRE/SE 16V M FM5 TP(5) 10M SRE/SE 16V M FM5 TP(5) 0.022UF 50V Z F TA26 S 0.022UF 50V Z F TA26 S 0.01M 16V M Y TA26 220M SRA 6.3V M FM5 TP(5) REMARK MODEL : NTH960 S AL LOCA.NO. C332 C333 C334 C336 C337 C338 C339 C340 C341 C343 C344 C345 C346 C348 C349 C354 C355 C358 C360 C368 C369 C375 C377 C380 C381 C384 C386 C3B1 C3G1 C3G2 C3G3 C3G4 C3G5 C3G6 C3G7 C3G8 C3G9 C401 C402 C403 C405 C406 C410 C412 C413 C414 C415 C416 C417 C418 C419 C420 C421 C424 C431 C466 C480 C490 C501 C502 RUN DATE : 2004.05.01 PART NO 0CN1030F678 0CN1040K948 0CN223AK948 0CN1030F678 0CE4754K638 0CN223AK948 0CE1054K638 0CN3330K518 0CN223AK948 0CN4730K948 0CN1040K948 0CN1040K948 0CE2274C638 0CN1030F678 0CN223AK948 0CE2274C638 0CN1030F678 0CE1054K638 0CC0500K015 0CN1020K518 0CN1040K948 0CN1040K948 0CE1044K638 0CN223AK948 0CE4764F638 0CE4774C638 0CN223AK948 0CN3330K518 0CN223AK948 0CE4764F638 0CN3320F668 0CN4730K948 0CE4754K638 0CE4754K638 0CE4754K638 0CN1030F678 0CN223AK948 0CE4764F638 0CN223AK948 0CN1040K948 0CE1063F638 0CE1063F638 0CN1040K948 0CN1040K948 0CQ1032K409 0CQ1032K409 0CE2264F638 0CN2220F668 0CN1820F668 0CQ1532K409 0CQ1032K409 0CE4765K618 0CQ2232L559 0CN1040K948 0CN1030F678 0CE3354K638 0CE4754K638 0CE1054K638 0CN1040K948 0CE4764C638 DESCRIPTION CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED TUBULAR(High d CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,FIXED TUBULAR(High d CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR,CERAMIC(TEMP COMP) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR,ELECTROLYTIC CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,FIXED TUBULAR(High d CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,ELECTROLYTIC CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,FIXED TUBULAR(High d CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,ELECTROLYTIC CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR,AL.ELECTROLYTIC CAPACITOR,AL.ELECTROLYTIC CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR,FIXED FILM CAPACITOR,FIXED FILM CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED FILM CAPACITOR,FIXED FILM CAPACITOR,AL.ELECTROLYTIC CAPACITOR,FIXED FILM CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR,ELECTROLYTIC - 5-4 - SPECIFICATION 0.01M 16V M Y TA26 0.1UF D 50V 80%,-20% F(Y5V) TA 0.022UF 50V Z F TA26 S 0.01M 16V M Y TA26 4.7UF SRA,SS 50V 20% FM5 TP 5 0.022UF 50V Z F TA26 S 1.0M SRA/SS50V M FM5 TP(5) 0.033UF 50V K B TA26 0.022UF 50V Z F TA26 S 0.047UF D 50V 80%,-20% F(Y5V) 0.1UF D 50V 80%,-20% F(Y5V) TA 0.1UF D 50V 80%,-20% F(Y5V) TA 220M SRA 6.3V M FM5 TP(5) 0.01M 16V M Y TA26 0.022UF 50V Z F TA26 S 220M SRA 6.3V M FM5 TP(5) 0.01M 16V M Y TA26 1.0M SRA/SS50V M FM5 TP(5) 5P 50V C NP0 TR 1000P 50V K B TA26 0.1UF D 50V 80%,-20% F(Y5V) TA 0.1UF D 50V 80%,-20% F(Y5V) TA 0.1M SRA 50V M FM5 TP(5) 0.022UF 50V Z F TA26 S 47M SRA/SS 16V M FM5 TP(5) 470UF SRA,SS 6.3V 20% FM5 TP 5 0.022UF 50V Z F TA26 S 0.033UF 50V K B TA26 0.022UF 50V Z F TA26 S 47M SRA/SS 16V M FM5 TP(5) 3300P 16V M TA26 0.047UF D 50V 80%,-20% F(Y5V) 4.7UF SRA,SS 50V 20% FM5 TP 5 4.7UF SRA,SS 50V 20% FM5 TP 5 4.7UF SRA,SS 50V 20% FM5 TP 5 0.01M 16V M Y TA26 0.022UF 50V Z F TA26 S 47M SRA/SS 16V M FM5 TP(5) 0.022UF 50V Z F TA26 S 0.1UF D 50V 80%,-20% F(Y5V) TA 10M SRE/SE 16V M FM5 TP(5) 10M SRE/SE 16V M FM5 TP(5) 0.1UF D 50V 80%,-20% F(Y5V) TA 0.1UF D 50V 80%,-20% F(Y5V) TA 0.01UF S 50V 5% PE TP5 0.01UF S 50V 5% PE TP5 22UF SRA,SS 16V 20% FM5 TP 5 2200P 16V M X TA26 1800P 16V M X TA26 0.015UF S 50V 5% PE TP5 0.01UF S 50V 5% PE TP5 47UF SR,SV 50V M FL TP 5 0.022UF S 63V 10% PP NI TP5 0.1UF D 50V 80%,-20% F(Y5V) TA 0.01M 16V M Y TA26 3.3UF SRA,SS 50V 20% FM5 TP 5 4.7UF SRA,SS 50V 20% FM5 TP 5 1.0M SRA/SS50V M FM5 TP(5) 0.1UF D 50V 80%,-20% F(Y5V) TA 47M SRA 6.3V M FM5 TP(5) REMARK MODEL : NTH960 S AL LOCA.NO. C503 C505 C507 C509 C510 C514 C515 C516 C517 C520 C521 C522 C525 C526 C528 C529 C530 C534 C535 C540 C541 C542 C543 C544 C545 C546 C551 C552 C554 C555 C557 C561 C567 C570 C571 C573 C574 C576 C581 C582 C583 C584 C5F1 C5F2 C6F3 C6F4 C6F5 C6F8 C5K0 C5K1 C5K2 C6R1 C601 C602 C603 C604 C605 C901 C902 C903 C904 RUN DATE : 2004.05.01 PART NO 0CE4774C638 0CE1074F638 0CN1030F678 0CN223AK948 0CN1030F678 0CC1500K415 0CC1200K415 0CE1054K636 0CE4774C638 0CN1030F678 0CN1040K948 0CN1030F678 0CN223AK948 0CE4764J638 0CN1030F678 0CN1040K948 0CE4764C638 0CE4754K638 0CE4754K638 0CE4764F638 0CE4754K638 0CN6810K518 0CN2220F668 0CQ3332K409 0CN2220F668 0CE4764H638 0CQ4732K409 0CN1030F678 0CN1040K948 0CE2264F638 0CN1040K948 0CE4764C638 0CN1020K518 0CC1200K415 0CC1500K415 0CN5610K518 0CN1020K518 0CE2264F638 0CN1030F678 0CN1030F678 0CN1040K948 0CE1054K636 0CE4766K638 0CE4766K638 0CE4764C638 0CN1030F678 0CN1030F678 0CE4766K638 0CN1030F678 0CN1030F678 0CN1030F678 0CE4764C638 0CN1030F678 0CN1030F678 0CN1030F678 0CN1030F678 0CN1030F678 0CN1020K518 0CN1020K518 0CN1020K518 0CN1020K518 DESCRIPTION CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,CERAMIC(TEMP COMP) CAPACITOR,FIXED CERAMIC(TEMP.C CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,AL.ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,FIXED FILM CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,FIXED FILM CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED CERAMIC(TEMP.C CAPACITOR,CERAMIC(TEMP COMP) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,FIXED TUBULAR(HIGH D CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) CAPACITOR TUBULA(HIGH DIELE) - 5-5 - SPECIFICATION 470UF SRA,SS 6.3V 20% FM5 TP 5 100U SRA 16V M FM5 TP(5) 0.01M 16V M Y TA26 0.022UF 50V Z F TA26 S 0.01M 16V M Y TA26 15P 50V J NP0 TS 12PF D 50V 5% TR NP0 1.0U SRA 50V M FM5 BP TP(D) 470UF SRA,SS 6.3V 20% FM5 TP 5 0.01M 16V M Y TA26 0.1UF D 50V 80%,-20% F(Y5V) TA 0.01M 16V M Y TA26 0.022UF 50V Z F TA26 S 47UF SRA,SS 35V M FM5 TP 5 0.01M 16V M Y TA26 0.1UF D 50V 80%,-20% F(Y5V) TA 47M SRA 6.3V M FM5 TP(5) 4.7UF SRA,SS 50V 20% FM5 TP 5 4.7UF SRA,SS 50V 20% FM5 TP 5 47M SRA/SS 16V M FM5 TP(5) 4.7UF SRA,SS 50V 20% FM5 TP 5 680P 50V K B TA26 2200P 16V M X TA26 0.033UF S 50V 5% PE TP5 2200P 16V M X TA26 47M SRA 25V M FM5 TP(5) 0.047UF S 50V 5% PE TP5 0.01M 16V M Y TA26 0.1UF D 50V 80%,-20% F(Y5V) TA 22UF SRA,SS 16V 20% FM5 TP 5 0.1UF D 50V 80%,-20% F(Y5V) TA 47M SRA 6.3V M FM5 TP(5) 1000P 50V K B TA26 12PF D 50V 5% TR NP0 15P 50V J NP0 TS 560P 50V K B TA26 1000P 50V K B TA26 22UF SRA,SS 16V 20% FM5 TP 5 0.01M 16V M Y TA26 0.01M 16V M Y TA26 0.1UF D 50V 80%,-20% F(Y5V) TA 1.0U SRA 50V M FM5 BP TP(D) 47M SMS 50V M FM5 TP 47M SMS 50V M FM5 TP 47M SRA 6.3V M FM5 TP(5) 0.01M 16V M Y TA26 0.01M 16V M Y TA26 47M SMS 50V M FM5 TP 0.01M 16V M Y TA26 0.01M 16V M Y TA26 0.01M 16V M Y TA26 47M SRA 6.3V M FM5 TP(5) 0.01M 16V M Y TA26 0.01M 16V M Y TA26 0.01M 16V M Y TA26 0.01M 16V M Y TA26 0.01M 16V M Y TA26 1000P 50V K B TA26 1000P 50V K B TA26 1000P 50V K B TA26 1000P 50V K B TA26 REMARK MODEL : NTH960 S AL LOCA.NO. C906 C907 C908 C909 C910 C911 C917 C918 C919 C921 C922 C923 C924 RUN DATE : 2004.05.01 PART NO 0CN223AK948 0CE4764F638 0CE1054K638 0CE1054K638 0CE1054K638 0CE1054K638 0CN223AK948 0CE4754K638 0CE1064F638 0CE1074F638 0CX2700K408 0CE2264F638 0CE4774C638 FL401 L103 L104 L301 L302 L303 L304 L306 L307 L309 L380 L3G1 L401 L405 L503 L504 L505 L901 L902 L904 633-032K 633-088G 633-088G 0LR1800K035 0LA0472K018 0LA1200K018 0LR4700K035 0LR2200K035 0LR4700K035 0LR2700J025 0LR1000K035 0LR1000K035 0LR1000K035 0LR1000K035 0LR1000K035 0LA1000K018 0LR1000K035 0LA1000K018 0LA1000K018 0LR1000K035 BD101 D102 D103 D106 D107 D108 D109 D110 D154 D155 D156 D158 D159 D161 D301 D380 D401 D402 D403 D501 D510 D511 D5F6 D901 D902 0DD160000DA 0DD010009CA 0DR180209AA 0DR158220AA 0DR180209AA 0DD010009AC 0DR302000AB 0DD010009AC 0DD207000AB 0DD207000AB 0DD207000AB 0DR104009AB 0DR104009AB 0DR104009AB 0DD133009AA 0DD133009AA 0DD133009AA 0DD133009AA 0DD133009AA 0DD133009AA 0DD133009AA 0DD133009AA 0DD133009AA 0DD133009AA 0DD133009AA DESCRIPTION CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,TUBULAR(HIGH DIELEC) CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR,ELECTROLYTIC CAPACITOR TUBULA(T.C) CAPACITOR,FIXED ELECTROLYTIC CAPACITOR,FIXED ELECTROLYTIC COIL COIL,IFT COIL,CHOKE COIL,CHOKE INDUCTOR RADIAL LEAD INDUCTOR AXIAL LEAD INDUCTOR AXIAL LEAD INDUCTOR RADIAL LEAD INDUCTOR RADIAL LEAD INDUCTOR RADIAL LEAD INDUCTOR,RADIAL LEAD INDUCTOR RADIAL LEAD INDUCTOR RADIAL LEAD INDUCTOR RADIAL LEAD INDUCTOR RADIAL LEAD INDUCTOR RADIAL LEAD INDUCTOR AXIAL LEAD INDUCTOR RADIAL LEAD INDUCTOR AXIAL LEAD INDUCTOR AXIAL LEAD INDUCTOR RADIAL LEAD DIODE DIODE,RECTIFIERS DIODE,RECTIFIERS DIODE,RECTIFIERS DIODE,RECTIFIERS DIODE,RECTIFIERS DIODE,RECTIFIERS DIODE,RECTIFIERS DIODE,RECTIFIERS DIODE,RECTIFIERS DIODE,RECTIFIERS DIODE,RECTIFIERS DIODE,RECTIFIERS DIODE,RECTIFIERS DIODE,RECTIFIERS DIODE,SWITCHING DIODE,SWITCHING DIODE,SWITCHING DIODE,SWITCHING DIODE,SWITCHING DIODE,SWITCHING DIODE,SWITCHING DIODE,SWITCHING DIODE,SWITCHING DIODE,SWITCHING DIODE,SWITCHING - 5-6 - SPECIFICATION 0.022UF 50V Z F TA26 S 47M SRA/SS 16V M FM5 TP(5) 1.0M SRA/SS50V M FM5 TP(5) 1.0M SRA/SS50V M FM5 TP(5) 1.0M SRA/SS50V M FM5 TP(5) 1.0M SRA/SS50V M FM5 TP(5) 0.022UF 50V Z F TA26 S 4.7UF SRA,SS 50V 20% FM5 TP 5 10M SRA 16V M FM5 TP(5) 100U SRA 16V M FM5 TP(5) 27P 50V J SL TA26 22UF SRA,SS 16V 20% FM5 TP 5 470UF SRA,SS 6.3V 20% FM5 TP 5 NON BIAC OSC,1CHIP 5V(KS-75M) 22MH TOKO 5MM TP 22MH TOKO 5MM TP 180M K 6X6 L5 TP 47M K 2.3X3.4 L5 TP 120M K 2.3X3.4 L5 TP 470M K 6X6 L5 TP 220M K 6X6 L5 TP 470M K 6X6 L5 TP 270UH 5% 4X5 TR5 100M K 6X6 L5 TP 100M K 6X6 L5 TP 100M K 6X6 L5 TP 100M K 6X6 L5 TP 100M K 6X6 L5 TP 100M K 2.3X3.4 L5 TP 100M K 6X6 L5 TP 100M K 2.3X3.4 L5 TP 100M K 2.3X3.4 L5 TP 100M K 6X6 L5 TP S1WBA60 BK SHINDENGEN - 600V EG01C TP SANKEN - - - - - ERA18-02KFRB TP FUJI DO204AL 2 1N5822 BK RECTRON DO201AD 40V ERA18-02KFRB TP FUJI DO204AL 2 EU01W(R-FORM) TP SANKEN HER302 BK RECTRON DO201AD 100V EU01W(R-FORM) TP SANKEN 2A07 2A RECT(T/S)P=12.5 F DELT 2A07 2A RECT(T/S)P=12.5 F DELT 2A07 2A RECT(T/S)P=12.5 F DELT RL104 R. TP GULF SEMICONDUCTOR RL104 R. TP GULF SEMICONDUCTOR RL104 R. TP GULF SEMICONDUCTOR 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP REMARK MODEL : NTH960 S AL LOCA.NO. D903 D904 D905 RUN DATE : 2004.05.01 PART NO 0DD133009AA 0DD133009AA 0DD133009AA DG601 6302R-V106A BC101 BD901 BD902 BD903 BD904 BD905 BD906 BD907 BD908 BD909 BD910 BD911 BD922 L102 W1A2 636-004C 636-004C 636-004C 636-004C 636-004C 636-004C 636-004C 636-004C 636-004C 636-004C 636-004C 636-004C 636-004C 616-145H 636-004C F101 0FS1601B51B ES501 ES502 FH01 FH02 LD501 4931R-0050A 4931R-0050A 586-008B 586-008B 4931R-0017A F104 IC101 IC103 IC301 IC3G1 IC501 IC503 IC505 IC6F1 IC901 GIRH100000B 0ISK615300A 0ISS431000A 0ISA715820A 0IMA391600A 0IMCRMA024B 0ICS241600B 0IKE704200B 0IPRPPY002A 0IJR641300A JK901 JK902 572-034R 572-034R LD601 LD602 6301R1K001A 6301R1K001A FR101 R101 R102 R103 R104 R107 R109 R114 R116 R117 R118 R119 R120 0RF0471Q619 614-007A 0RS1003K619 0RD0681F608 0RS5602K619 0RD1504H632 0RS0350K619 0RD1003F608 0RD3300F608 0RD2201F608 0RD1001F608 0RN3301F408 0RN2701F408 DESCRIPTION DIODE,SWITCHING DIODE,SWITCHING DIODE,SWITCHING DIGITRON DIGITRON FILTER FILTER(CIRC),EMC FILTER(CIRC),EMC FILTER(CIRC),EMC FILTER(CIRC),EMC FILTER(CIRC),EMC FILTER(CIRC),EMC FILTER(CIRC),EMC FILTER(CIRC),EMC FILTER(CIRC),EMC FILTER(CIRC),EMC FILTER(CIRC),EMC FILTER(CIRC),EMC FILTER(CIRC),EMC FILTER(CIRC),DRAWING FILTER(CIRC),EMC FUSE FUSE,SLOW BLOW HOLDER HOLDER ASSY HOLDER ASSY HOLDER HOLDER HOLDER ASSEMBLY IC IC,ROHM IC,SANKEN IC,SAMSUNG ELECTRONICS IC,SANYO IC,MATSUSHITA IC,MICRO CONTROLLER IC,CATALYST IC,KEC IC,PERIPHERALS IC,JRC JACK JACK,RCA JACK,RCA LED LED ASSY LED ASSY RESISTOR RESISTOR,DRAWING RESISTOR RESISTOR,FIXED METAL OXIDE FIL RESISTOR,FIXED CARBON FILM RESISTOR,FIXED METAL OXIDE FIL RESISTOR,FIXED CARBON FILM RESISTOR,FIXED METAL OXIDE FIL RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED METAL FILM RESISTOR,FIXED METAL FILM - 5-7 - SPECIFICATION 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 1SS133 DETECT,SW TP 9MT-173GNK FUTABA UNIVERSAL LV BEAD CORE BFS3550R2FD8,R T/P BEAD CORE BFS3550R2FD8,R T/P BEAD CORE BFS3550R2FD8,R T/P BEAD CORE BFS3550R2FD8,R T/P BEAD CORE BFS3550R2FD8,R T/P BEAD CORE BFS3550R2FD8,R T/P BEAD CORE BFS3550R2FD8,R T/P BEAD CORE BFS3550R2FD8,R T/P BEAD CORE BFS3550R2FD8,R T/P BEAD CORE BFS3550R2FD8,R T/P BEAD CORE BFS3550R2FD8,R T/P BEAD CORE BFS3550R2FD8,R T/P BEAD CORE BFS3550R2FD8,R T/P SHT LFS2020V4-04350 BEAD CORE BFS3550R2FD8,R T/P 1600MA 250 V 5.2X20 CY/GL KS / END END FUSE CLIP TP SINSUNG FUSE CLIP TP SINSUNG MV995A NON LED ICP-N10 T104 TP IC DETACT STR-G6153T 5PIN FM CUT BK PWM KA431AZ (LM431AZ) LA71582M 100QFP BK AVCP TIMELA AN3916 SDIP ST AGC IC MN101D06F LE 2ND MATSUSHITA 10 CAT24WC16P 8P DIP ST 16K SERIA KIA7042P 3P 4.2V RESET(TAPING) PT6315 PTC 44 LQFP TRAY VFD DR NJU6413AD 16P DIP ST RS232C DR BJP-202-WH BAE EUN (WHITE) ST, BJP-202-WH BAE EUN (WHITE) ST, LTL16KEEH74 LITEON KOREA 17 LTL16KEEH74 LITEON KOREA 17 4.7 OHM 1/4 W(3.4) 5.00% TR 2.7/2W CEMENT SMPS V 100K OHM 2 W 5.00% TR 6.8 OHM 1/6 W 5.00% TA26 56K OHM 2 W 5.00% TR 1.5M OHM 1/2 W 5.00% MF10 0.35 OHM 2 W 5.00% TR 100K OHM 1/6 W 5% TA26 330 OHM 1/6 W 5% TA26 2.2K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 3.3K OHM 1/6 W 1% TA26 2.7K OHM 1/6 W 1% TA26 REMARK MODEL : NTH960 S AL LOCA.NO. R121 R122 R152 R156 R157 R161 R162 R166 R167 R168 R170 R171 R172 R173 R174 R175 R177 R302 R303 R304 R305 R306 R307 R308 R309 R310 R311 R312 R313 R316 R317 R318 R319 R320 R321 R322 R326 R335 R338 R340 R341 R349 R380 R381 R384 R385 R386 R387 R388 R389 R390 R391 R392 R393 R3B1 R3G1 R3G2 R3G3 R3G4 R3G5 RUN DATE : 2004.05.01 PART NO 0RD1800F608 0RD1003F608 0RD5600F608 0RD1001F608 0RD3300F608 0RD4701F608 0RD4701F608 0RD2201F608 0RD3901F608 0RD4701F608 0RD1001F608 0RD3301F608 0RD4701F608 0RD1001F608 0RD3300F608 0RD4701F608 0RD4701F608 0RD1002F608 0RD1802F608 0RD1002F608 0RD1001F608 0RD2700F608 0RD3300F608 0RD2701F608 0RD6800F608 0RD1001F608 0RD4701F608 0RD1801F608 0RD2700F608 0RD1500F608 0RD6802F608 0RD1001F608 0RD1001F608 0RD1501F608 0RD1801F608 0RD8201F608 0RD2701F608 0RD3902F608 0RD2700F608 0RD1802F608 0RD2701F608 0RD5601F608 0RD2200F608 0RD1001F608 0RD1800F608 0RD1800F608 0RD0752F608 0RD1004F608 0RD0752F608 0RD1502F608 0RD5601F608 0RD4702F608 0RD2201F608 0RD4702F608 0RD3901F608 0RD5601F608 0RD2702F608 0RD3902F608 0RD1503F608 0RD1800F608 DESCRIPTION RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM - 5-8 - SPECIFICATION 180 OHM 1/6 W 5% TA26 100K OHM 1/6 W 5% TA26 560 OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 330 OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 2.2K OHM 1/6 W 5% TA26 3.9K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 3.3K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 330 OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 18K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 270 OHM 1/6 W 5% TA26 330 OHM 1/6 W 5% TA26 2.7K OHM 1/6 W 5% TA26 680 OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 1.8K OHM 1/6 W 5% TA26 270 OHM 1/6 W 5% TA26 150 OHM 1/6 W 5% TA26 68K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1.5K OHM 1/6 W 5% TA26 1.8K OHM 1/6 W 5% TA26 8.2K OHM 1/6 W 5% TA26 2.7K OHM 1/6 W 5% TA26 39K OHM 1/6 W 5% TA26 270 OHM 1/6 W 5% TA26 18K OHM 1/6 W 5% TA26 2.7K OHM 1/6 W 5% TA26 5.6K OHM 1/6 W 5% TA26 220 OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 180 OHM 1/6 W 5% TA26 180 OHM 1/6 W 5% TA26 75 OHM 1/6 W 5.00% TA26 1M OHM 1/6 W 5% TA26 75 OHM 1/6 W 5.00% TA26 15K OHM 1/6 W 5% TA26 5.6K OHM 1/6 W 5% TA26 47K OHM 1/6 W 5% TA26 2.2K OHM 1/6 W 5% TA26 47K OHM 1/6 W 5% TA26 3.9K OHM 1/6 W 5% TA26 5.6K OHM 1/6 W 5% TA26 27K OHM 1/6 W 5% TA26 39K OHM 1/6 W 5% TA26 150K OHM 1/6 W 5% TA26 180 OHM 1/6 W 5% TA26 REMARK S AL LOCA.NO. R3G6 R402 R403 R404 R406 R408 R409 R410 R411 R412 R413 R414 R415 R416 R418 R419 R420 R421 R424 R425 R430 R431 R482 R486 R488 R490 R491 R492 R493 R501 R502 R504 R505 R507 R508 R509 R510 R511 R512 R513 R515 R516 R517 R6F1 R6F2 R521 R522 R525 R526 R527 R529 R532 R534 R541 R543 R544 R546 R547 R548 R550 PART NO 0RD1800F608 0RD2204F608 0RD6801F608 0RD5600F608 0RD3301F608 0RD2201F608 0RD4701F608 0RD1002F608 0RD2202F608 0RD1801F608 0RD8201F608 0RD1202F608 0RD3303F608 0RD1800F608 0RD1802F608 0RD0472F608 0RD1001F608 0RD0221F608 0RD2700F608 0RD4702F608 0RD3901F608 0RD4701F608 0RD1001F608 0RD5600F608 0RD2202F608 0RD4702F608 0RD1202F608 0RD1501F608 0RD0102F608 0RD2200F608 0RD2200F608 0RD1001F608 0RD1001F608 0RD1201F608 0RD5600F608 0RD6800F608 0RD1503F608 0RD1001F608 0RD1001F608 0RD3901F608 0RD2700F608 0RD2200F608 0RD2200F608 0RD5600F608 0RD5600F608 0RD1002F608 0RD1001F608 0RD1002F608 0RD1002F608 0RD1000F608 0RD1002F608 0RD6802F608 0RD2201F608 0RD2201F608 0RD2701F608 0RD4701F608 0RD4701F608 0RD1002F608 0RD1003F608 0RD2200F608 DESCRIPTION RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM - 5-9 - SPECIFICATION 180 OHM 1/6 W 5% TA26 2.2M OHM 1/6 W 0.05 TA26 6.8K OHM 1/6 W 5% TA26 560 OHM 1/6 W 5% TA26 3.3K OHM 1/6 W 5% TA26 2.2K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 22K OHM 1/6 W 5% TA26 1.8K OHM 1/6 W 5% TA26 8.2K OHM 1/6 W 5% TA26 12K OHM 1/6 W 5% TA26 330K OHM 1/6 W 5% TA26 180 OHM 1/6 W 5% TA26 18K OHM 1/6 W 5% TA26 47 OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 2.2 OHM 1/6 W 5% TA26 270 OHM 1/6 W 5% TA26 47K OHM 1/6 W 5% TA26 3.9K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 560 OHM 1/6 W 5% TA26 22K OHM 1/6 W 5% TA26 47K OHM 1/6 W 5% TA26 12K OHM 1/6 W 5% TA26 1.5K OHM 1/6 W 5% TA26 10 OHM 1/6 W 5% TA26 220 OHM 1/6 W 5% TA26 220 OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1.2K OHM 1/6 W 5% TA26 560 OHM 1/6 W 5% TA26 680 OHM 1/6 W 5% TA26 150K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 3.9K OHM 1/6 W 5% TA26 270 OHM 1/6 W 5% TA26 220 OHM 1/6 W 5% TA26 220 OHM 1/6 W 5% TA26 560 OHM 1/6 W 5% TA26 560 OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 100 OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 68K OHM 1/6 W 5% TA26 2.2K OHM 1/6 W 5% TA26 2.2K OHM 1/6 W 5% TA26 2.7K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 100K OHM 1/6 W 5% TA26 220 OHM 1/6 W 5% TA26 REMARK MODEL : NTH960 S AL LOCA.NO. R553 R554 R555 R556 R557 R558 R559 R560 R563 R564 R567 R569 R570 R571 R572 R573 R574 R575 R576 R577 R578 R579 R580 R581 R582 R583 R585 R589 R590 R591 R592 R593 R595 R596 R597 R598 R5B1 R5B3 R5B4 R5C5 R5C6 R5C7 R5F0 R5F1 R5F2 R5F3 R6F4 R6F5 R6F6 R6F7 R5K0 R5K1 R5K2 R6R1 R603 R604 R605 R606 R607 R608 R609 RUN DATE : 2004.05.01 PART NO 0RD2200F608 0RD4700F608 0RD2200F608 0RD2202F608 0RD2702F608 0RD2202F608 0RD4701F608 0RD4701F608 0RD4701F608 0RD2702F608 0RD4701F608 0RD4701F608 0RD4701F608 0RD2202F608 0RD1001F608 0RD8200F608 0RD4701F608 0RD4701F608 0RD4701F608 0RD4701F608 0RD4701F608 0RD5602F608 0RD5600F608 0RD5600F608 0RD1001F608 0RD1002F608 0RD1001F608 0RD2700F608 0RD1001F608 0RD4701F608 0RD4702F608 0RD1202F608 0RD1000F608 0RD1000F608 0RD1000F608 0RD1000F608 0RD1001F608 0RD1001F608 0RD1001F608 0RD1001F608 0RD1001F608 0RD1001F608 0RD0122F608 0RD0122F608 0RD0102F608 0RD0102F608 0RD1001F608 0RD1001F608 0RD1001F608 0RD5602F608 0RD1002F608 0RD1002F608 0RD1002F608 0RD3300F608 0RD1801F608 0RD1801F608 0RD1501F608 0RD1501F608 0RD2201F608 0RD2201F608 0RD2701F608 DESCRIPTION RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM - 5-10 - SPECIFICATION 220 OHM 1/6 W 5% TA26 470 OHM 1/6 W 5% TA26 220 OHM 1/6 W 5% TA26 22K OHM 1/6 W 5% TA26 27K OHM 1/6 W 5% TA26 22K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 27K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 22K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 820 OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 56K OHM 1/6 W 5% TA26 560 OHM 1/6 W 5% TA26 560 OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 270 OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 4.7K OHM 1/6 W 5% TA26 47K OHM 1/6 W 5% TA26 12K OHM 1/6 W 5% TA26 100 OHM 1/6 W 5% TA26 100 OHM 1/6 W 5% TA26 100 OHM 1/6 W 5% TA26 100 OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 12 OHM 1/6 W 5.00% TA26 12 OHM 1/6 W 5.00% TA26 10 OHM 1/6 W 5% TA26 10 OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 56K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 330 OHM 1/6 W 5% TA26 1.8K OHM 1/6 W 5% TA26 1.8K OHM 1/6 W 5% TA26 1.5K OHM 1/6 W 5% TA26 1.5K OHM 1/6 W 5% TA26 2.2K OHM 1/6 W 5% TA26 2.2K OHM 1/6 W 5% TA26 2.7K OHM 1/6 W 5% TA26 REMARK MODEL : NTH960 S AL LOCA.NO. R610 R611 R612 R613 R614 R615 R616 R617 R618 R621 R622 R623 R624 R625 R626 R627 R628 R629 R630 R634 R635 R636 R637 R638 R904 R905 R906 R907 R908 R909 R910 R911 R912 R914 R915 R916 R917 R918 R919 R920 R921 R922 R923 R924 R925 R926 R927 R928 R929 R930 R931 R932 R933 R934 R935 R936 R937 R938 R939 R940 RUN DATE : 2004.05.01 PART NO 0RD2701F608 0RD3901F608 0RD3901F608 0RD6801F608 0RD6801F608 0RD1202F608 0RD1202F608 0RD6802F608 0RD1002F608 0RD1801F608 0RD1501F608 0RD2201F608 0RD2701F608 0RD6802F608 0RD6802F608 0RD6802F608 0RD6802F608 0RD6802F608 0RD6802F608 0RD0101F608 0RD0101F608 0RD0101F608 0RD0101F608 0RD0101F608 0RD1001F608 0RD1001F608 0RD1001F608 0RD1001F608 0RD1001F608 0RD1001F608 0RD1001F608 0RD1001F608 0RD1001F608 0RD1001F608 0RD1001F608 0RD1002F608 0RD1002F608 0RD1002F608 0RD1002F608 0RD1002F608 0RD1002F608 0RD1002F608 0RD1002F608 0RD1002F608 0RD1002F608 0RD1002F608 0RD1002F608 0RD1002F608 0RD1002F608 0RD1001F608 0RD5600F608 0RD1002F608 0RD1001F608 0RD2201F608 0RD1001F608 0RD1002F608 0RD2702F608 0RD8201F608 0RD2200F608 0RD0562F608 DESCRIPTION RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM RESISTOR,FIXED CARBON FILM - 5-11 - SPECIFICATION 2.7K OHM 1/6 W 5% TA26 3.9K OHM 1/6 W 5% TA26 3.9K OHM 1/6 W 5% TA26 6.8K OHM 1/6 W 5% TA26 6.8K OHM 1/6 W 5% TA26 12K OHM 1/6 W 5% TA26 12K OHM 1/6 W 5% TA26 68K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 1.8K OHM 1/6 W 5% TA26 1.5K OHM 1/6 W 5% TA26 2.2K OHM 1/6 W 5% TA26 2.7K OHM 1/6 W 5% TA26 68K OHM 1/6 W 5% TA26 68K OHM 1/6 W 5% TA26 68K OHM 1/6 W 5% TA26 68K OHM 1/6 W 5% TA26 68K OHM 1/6 W 5% TA26 68K OHM 1/6 W 5% TA26 1 OHM 1/6 W 5.00% TA26 1 OHM 1/6 W 5.00% TA26 1 OHM 1/6 W 5.00% TA26 1 OHM 1/6 W 5.00% TA26 1 OHM 1/6 W 5.00% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 560 OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 2.2K OHM 1/6 W 5% TA26 1K OHM 1/6 W 5% TA26 10K OHM 1/6 W 5% TA26 27K OHM 1/6 W 5% TA26 8.2K OHM 1/6 W 5% TA26 220 OHM 1/6 W 5% TA26 56 OHM 1/6 W 5% TA26 REMARK S AL LOCA.NO. VR501 VR601 PART NO 613-032W 611-024B RC6R1 6712R2938GA IC102 RS501 RS502 657-063A 6500RAB003A 6500RAB003A CS501 JS601 MS501 SL601 SW601 SW602 SW603 SW604 SW605 SW606 SW607 SW608 SW609 SW610 SW611 SW612 SW613 SW614 SW615 SW616 SW617 SW618 SW619 SW620 SW621 SW901 6600M000026 556-272A 6600JB8005B 6600Q000007 556-219B 556-219B 556-219B 556-219B 556-219B 556-219B 556-219B 556-219B 556-219B 556-219B 556-219B 556-219B 556-219B 556-219B 556-219B 556-219B 556-219B 556-219B 556-219B 556-219B 556-219B 556-219B Q152 Q153 Q155 Q156 Q157 Q159 Q161 Q162 Q163 Q164 Q301 Q302 Q303 Q304 Q305 Q380 Q381 Q382 Q3G1 Q402 Q403 Q404 Q405 Q406 Q481 0TR320309AA 0TR127309AA 0TR127309AA 0TR120309AE 0TR120309AE 0TR127309AA 0TR319809AC 0TR120309AE 0TR127309AA 0TR120309AE 0TR319809AC 0TR319809AC 0TR126609AE 0TR319809AC 0TR319809AC 0TR126609AE 0TR319809AC 0TR126609AE 0TR126609AE 0TR126609AE 0TR319809AC 0TR319809AC 0TR320309AA 0TR319809AC 0TR126609AE DESCRIPTION RESISTOR,DRAWING RESISTOR,DRAWING REMOTE CONTROLLER RECEIVER REMOTE CONTROLLER RECEIVER SENSOR SENSOR SENSOR SENSOR SWITCH SWITCH,PUSH SWITCH SWITCH,MODE SWITCH,SLIDE SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT TRANSISTOR TRANSISTOR,BIPOLARS TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR,BIPOLARS TRANSISTOR TRANSISTOR - 5-12 - SPECIFICATION RH063MCJ5R (220K) RK09K113000123B TSOP1238SP1 VISHAY(TEMIC) 37-9 LTV-817B,PHOTO COUPLER(LITEON) SG-260 KODENSHI D33 REEL SENSO SG-260 KODENSHI D33 REEL SENSO MPU12970MLB0 VCR CST IN S/W MI JRS0000-0502 SMK NON 1V 10MA V NON 5V 1MA VERTICAL -G CSS-2201A CHANG SHIN 30V DC 0. THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5THVV502GAA POSTECH DC 12 V 5KTC3203 KEC TP TO92 50V 150MA KTA1273-TP-Y (KTA966A)KEC KTA1273-TP-Y (KTA966A)KEC SRC1203 TP AUK TO92 22K,22K SRC1203 TP AUK TO92 22K,22K KTA1273-TP-Y (KTA966A)KEC KTC3198-TP-BL (KTC1815)KEC SRC1203 TP AUK TO92 22K,22K KTA1273-TP-Y (KTA966A)KEC SRC1203 TP AUK TO92 22K,22K KTC3198-TP-BL (KTC1815)KEC KTC3198-TP-BL (KTC1815)KEC KTA1266-GR,TP(KTA1015),KEC KTC3198-TP-BL (KTC1815)KEC KTC3198-TP-BL (KTC1815)KEC KTA1266-GR,TP(KTA1015),KEC KTC3198-TP-BL (KTC1815)KEC KTA1266-GR,TP(KTA1015),KEC KTA1266-GR,TP(KTA1015),KEC KTA1266-GR,TP(KTA1015),KEC KTC3198-TP-BL (KTC1815)KEC KTC3198-TP-BL (KTC1815)KEC KTC3203 KEC TP TO92 50V 150MA KTC3198-TP-BL (KTC1815)KEC KTA1266-GR,TP(KTA1015),KEC REMARK MODEL : NTH960 S AL LOCA.NO. Q501 Q502 Q503 Q504 Q506 Q512 Q513 Q514 Q515 Q521 Q901 Q902 Q903 Q904 Q905 Q906 Q907 Q908 Q909 Q910 Q911 Q912 Q913 Q914 RUN DATE : 2004.05.01 PART NO 0TR319809AC 0TR319809AA 0TR127309AA 0TR126609AE 0TR126609AE 0TR120309AE 0TR103009AF 0TR120309AE 0TR120309AE 0TR320309AA 0TR120309AE 0TR120309AE 0TR120309AE 0TR120309AE 0TR120309AE 0TR120309AE 0TR120309AE 0TR120309AE 0TR120309AE 0TR120309AE 0TR320309AA 0TR534309BA 0TR198009CA 0TR198009CA T101 642-023U V101 656-004C X302 X501 X502 6202R2357AE 6202R-DA01A 6202R1143DC ZD101 ZD152 ZD502 ZD503 ZD901 ZD902 ZD903 ZD904 ZD905 ZD906 ZD907 ZD908 ZD909 ZD910 ZD911 ZD912 ZD913 ZD914 ZD915 ZD916 ZD917 ZD920 0DZ332609FA 0DZ910009BB 0DZ622609AB 0DZ622609AB 0DZ132609BB 0DZ132609BB 0DZ132609BB 0DZ132609BB 0DZ132609BB 0DZ132609BB 0DZ132609BB 0DZ132609BB 0DZ132609BB 0DZ132609BB 0DZ132609BB 0DZ132609BB 0DZ132609BB 0DZ132609BB 0DZ132609BB 0DZ132609BB 0DZ132609BB 0DZ910009BB DESCRIPTION TRANSISTOR TRANSISTOR,BIPOLARS TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR,BIPOLARS TRANSISTOR TRANSISTOR TRANSISTOR,BIPOLARS TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR,BIPOLARS TRANSISTOR,BIPOLARS TRANSISTOR TRANSISTOR TRANSFORMER TRANSFORMER,SMPS[COIL] VARISTOR VARISTOR,DRAWING X-TAL RESONATOR,CRYSTAL RESONATOR,CRYSTAL RESONATOR,CRYSTAL ZENER DIODE DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER - 5-13 - SPECIFICATION KTC3198-TP-BL (KTC1815)KEC KTC3198(KTC1815) KEC TP TO92 5 KTA1273-TP-Y (KTA966A)KEC KTA1266-GR,TP(KTA1015),KEC KTA1266-GR,TP(KTA1015),KEC SRC1203 TP AUK TO92 22K,22K KRA103M(KRA2203) KEC TP TO92M SRC1203 TP AUK TO92 22K,22K SRC1203 TP AUK TO92 22K,22K KTC3203 KEC TP TO92 50V 150MA SRC1203 TP AUK TO92 22K,22K SRC1203 TP AUK TO92 22K,22K SRC1203 TP AUK TO92 22K,22K SRC1203 TP AUK TO92 22K,22K SRC1203 TP AUK TO92 22K,22K SRC1203 TP AUK TO92 22K,22K SRC1203 TP AUK TO92 22K,22K SRC1203 TP AUK TO92 22K,22K SRC1203 TP AUK TO92 22K,22K SRC1203 TP AUK TO92 22K,22K KTC3203 KEC TP TO92 50V 150MA 2SC5343-L TP AUK TO92 2SA1980G TP AUK TO92 2SA1980G TP AUK TO92 SJE-023U SJ/CS WIDE EER2828 SVC681D-10A SAMHWA 4.O CUT HC49U SSANG TAE 3-579575MHZ 1 CFS-308 CITIZEN 32-768KHZ 20 H49U BUBANG 14-31818HZ 25PPM 1 UZ-3.3BSB 26MM TP PYUNG CHANG MTZJ9.1C TP ROHM-K DO34 0.5W 8 UZ-6.2BSA 26MM TP PYUNG CHANG UZ-6.2BSA 26MM TP PYUNG CHANG UZ-13BSA 26MM TP PYUNG CHANG UZ-13BSA 26MM TP PYUNG CHANG UZ-13BSA 26MM TP PYUNG CHANG UZ-13BSA 26MM TP PYUNG CHANG UZ-13BSA 26MM TP PYUNG CHANG UZ-13BSA 26MM TP PYUNG CHANG UZ-13BSA 26MM TP PYUNG CHANG UZ-13BSA 26MM TP PYUNG CHANG UZ-13BSA 26MM TP PYUNG CHANG UZ-13BSA 26MM TP PYUNG CHANG UZ-13BSA 26MM TP PYUNG CHANG UZ-13BSA 26MM TP PYUNG CHANG UZ-13BSA 26MM TP PYUNG CHANG UZ-13BSA 26MM TP PYUNG CHANG UZ-13BSA 26MM TP PYUNG CHANG UZ-13BSA 26MM TP PYUNG CHANG UZ-13BSA 26MM TP PYUNG CHANG MTZJ9.1C TP ROHM-K DO34 0.5W 8 REMARK