Download Horizon DYN4300 battery charger
Transcript
NiMH RE-PEAK LiFe STORAGE 2 2.0A 19.8V(6S) NiMH CYCLE LiFe DISCHARGE DCHG>CHG 1 2.0A 19.8V(6S) LiFe BALANCE NiMH CHARGE LiIo NiCd CHARGE 2.0A 2.0A BALANCE 19.8V(6S) CURRENT 2.0A 21.6V(6S) CURRENT 2.0A LiFe BALANCE NiMH CHARGE 2.0A 19.8V(6S) CURRENTLiFe CHARGE 2.0A NiMH Auto CHARGE NiCd Auto CHARGE LiIo CHARGE 2.0A 19.8V(6S) CURRENT 2.0A CURRENT 2.0A 2.0A 21.6V(6S) LiFe CHARGE NiMH Auto CHARGE Instruction Manual | Bedienungsanleitung | Manuel d’utilisation | Manuale di Istruzioni (DYN4300) 2.0A 19.8V(6S) CURRENT 2.0A LiFe FAST CHG NiMH DISCHARGE PROGRAM SELECT PROGRAM SELECT PROGRAM SELECT NiCd DISCHARGE LiIo FAST CHG PROGRAMLiFe SELECT 2.0A 19.8V(6S) 0.1A CUT:1.0V NiMH NiCd BATT BATT 0.1A CUT: 1.0V 2.0A 21.6V(6S) BATT LiFe FAST CHG NiMH DISCHARGE PROGRAM SELECTLiIo BATT PROGRAM SELECT • Never attempt to charge a battery pack containing different types of batteries. NOTICE Not to scale. Programming quick Guide 2.0A 19.8V(6S) 0.1A CUT:1.0V NiMH RE-PEAK OPERATING YOUR CHARGER NiMH BATT LiFe BATT LiFe STORAGE • Never allow children under 14 years of age to charge battery packs. NiCd RE-PEAK LiIo STORAGE TAble of CONTENTS Press the Mode key (G) to get to the 9 main menus from any submenu screen. All instructions, warranties and other collateral documents are subject to change 2 Not all wiring shown. 2.0A 19.8V(6S) • Never charge batteries in extremely hot or cold places or place in direct sunlight. 2 NiMH RE-PEAK 2.0A 21.6V(6S) STORAGE Press the Jog Dial (H) to get to the submenusLiFe for adjusting operating parameters, to save value changes or to start chosen battery charging actions.2 1 SELF TEST AND PROGRAM SELECT SCREENS 18 Li-Po Storage Charging Programming and Operations at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature, visit Not all connectors shown. • Never charge a battery if the cable has been pinched or shorted. 2.0A 19.8V(6S) NiMH CYCLE LiFe DISCHARGE Rotate the Jog Dial (H) to change between submenu screens or to change screen values. NiCd CYCLE LiIo DISCHARGE 19 Li-Po Discharge 35 BATTERY MEMORY horizonhobby.com and click on the support tab for this product. LI-FE DCHG>CHG 1 • Never connect the charger if the power cable has been pinched or shorted. 2.0A 19.8V(6S) DCHG>CHG 1 NiMH CYCLE 2.0A 21.6V(6S) LiFe DISCHARGE 36 SYSTEM SET • Never connect the charger to an automobile 12V battery while the vehicle 2 Li-Fe BATTERIES Ni-MH DCHG>CHG 1 2.0A 19.8V(6S) Meaning of Special Language a REST TIME NiMH CHARGE LiFe BALANCE LiIo BALANCE NiCd CHARGE 20 Ni-MH BATTERIES is running. 3 Li-Fe Balance Charging Pb CHARGE LiPo BALANCE The following terms are used throughout the product literature to indicate various CURRENT2.0A 2.0A 2.0A 19.8V(6S) 21.6V(6S) CURRENT 2.0V 21 2.0A b SAFETY TIMER • Never attempt to dismantle the charger or use a damaged charger. 4 Li-Fe Charging Ni-MH Charging 2.0A (1P) 2.0A 22.2V(6S) LiIo BALANCE NiCd CHARGE PROGRAM SELECT LITHIUM BATTEries (Li-Fe) Lithium Batteries (li-Ion) levels of potential harm when operating this product: c CAPACITY CUTOFF • Never attach your charger to both an AC and a DC power source at the same time. 2.0A 21.6V(6S) CURRENT 2.0A 5 Li-Fe Fast Charging 22 Ni-MH Auto Charging LiFe CHARGE NiMH Auto CHARGE NiCd Auto CHARGE LiIo CHARGE Pb BATT Pb DISCHARGE2.0A LiPo CHARGE • Never connect the input jack (DC input) to AC power. d KEY BEEP/BUZZER 2.0A 19.8V(6S) CURRENT2.0A 2.0A NOTICE: Procedures, which if not properly followed, create a possibility of physical CURRENT 21.6V(6S) 6 Li-Fe Storage Charging 23 Ni-MH Discharge 2.0A 2.0V (1P) 2.0A 22.2V(6S) NiCd Auto CHARGE LiIo CHARGE • Always use only rechargeable batteries designed for use with this type of charger. e INPUT POWER LOW CUTOFF property damage AND a little or no possibility of injury. 7 Li-Fe Discharge 24 Ni-MH Re-Peak Charging 2.0A CHG 2.0A 21.6V(6S) PROGRAM SELECT LiFe FAST CHG NiMH DISCHARGE NiCd DISCHARGE PROGRAMPROGRAM SELECT SELECTCURRENT LiIo FAST PROGRAM SELECT • Always inspect the battery before charging. LiPo FAST CHG PROGRAM SELECT f EXTERNAL AND INTERNAL TEMPERATURES 25 Ni-MH Cycle Charging NiMH CHARGE LiFe BALANCE NiCd BATT 2.0A 19.8V(6S) 0.1A CUT:1.0V 0.1A CUT: 1.0V NiMH BATT CAUTION: Procedures, which if not properly followed, create the probability of 2.0A 21.6V(6S) Rest Time LiIo BATT LiFe BATT Li-IO • Always keep the battery away from any material that could be affected by heat. PROGRAM SELECTLiPo BATT 2.0A 22.2V(6S) NiCd DISCHARGE LiIo FAST CHG PROGRAM SELECT g RESET FACTORY SETTINGS 2.0A 19.8V(6S) CURRENT 2.0A CHG>DCHG 10min NiMH CHARGE LiFe BALANCE physical property damage AND a possibility of serious injury. 8 Li-Io BATTERIES 0.1A CUT:STORAGE 1.0V NiMH RE-PEAK 2.0A 21.6V(6S) LiIo BATT LiFe STORAGE • Always monitor the charging area and have a fire extinguisher available at all times. NiCd RE-PEAKNI-CD LiIo h VERSION 2.0A 19.8V(6S) NiCd BATT CURRENT 2.0A LiPo STORAGE 2 NiMH Auto CHARGE LiFe CHARGE 9 Li-Io Balance Charging 26 Ni-CD BATTERIES 2.0A 19.8V(6S) 2 2.0A 21.6V(6S) SAFETY TIMER WARNING: Procedures, which if not properly followed, create the probability of • Always end the charging process if the battery becomes hot to the touch or starts 2.0A 22.2V(6S) 37 Li BATTERY VOLTAGE CHECKER OPERATION NiCd RE-PEAK LiIo STORAGE 2.0A 19.8V(6S) CURRENT 2.0A ON 120min NiMH Auto2 CHARGE LiFe CHARGE 10 Li-Io Charging property damage, collateral damage, and serious injury OR create a high probability to change form (swell) during the charge process. NiMH CYCLE 2.0A 21.6V(6S) LiFe DISCHARGE NiCd CYCLE 27 Ni-CD Charging LiIo DISCHARGE USING THE BALANCE ADAPTER PORT 2.0A 19.8V(6S) CURRENT 2.0A LiPo DISCHARGE 11 Li-Io Fast Charging 28 Ni-CD • Always connect the charge cable to the charger first, then connect the battery to of superficial injury. 1 LiFe FAST CHG NiMH DISCHARGE PROGRAM SELECTDCHG>CHG 2.0A 19.8V(6S) DCHG>CHG Cut-Off 1 Auto Charging 2.0A 21.6V(6S) Capacity PROGRAM SELECTLiIo 38 USB ACCESSORY CHARGER OPERATION 2.0A 22.2V(6S) NiCd CYCLE DISCHARGE avoid short circuit between the charge leads. Reverse the sequence when 12 Li-Io Storage Charging 29 Ni-CD Discharge 2.0A FAST 19.8V(6S) 0.1A DISCHARGE CUT:1.0V BATT ON 5000mAh BATT LiFe CHG NiMH PROGRAMNiMH SELECT PROGRAMLiFe SELECT (COMPATIBLE WITH iPhone and iPod DEVICES) DCHG>CHG 1 2.0A 21.6V(6S) WARNING: Read the ENTIRE instruction manual to become familiar with the disconnecting. LiIo BALANCE NiCd CHARGE 2.0A 19.8V(6S) 0.1A CUT:1.0V Pb CHARGE NiMH BATT 13 Li-Io Discharge 30 Ni-CD Re-Peak Charging LiPo BALANCE LiFe BATT NiMH RE-PEAK LiFe STORAGE [BATT MEMORY 1] Key Beep ON 39 Troubleshooting Guide 2.0A 21.6V(6S) CURRENT 2.0A features of the product before operating. Failure to operate the product 2.0A 2.0V (1P) • Always connect the positive red leads (+) and negative black leads (–) correctly. 2.0A 22.2V(6S) 31 Ni-CD Cycle Charging PROGRAM SELECT Li-PO 2.0A STORAGE 19.8V(6S) SET ->2 Pb CHARGE NiMH ENTER RE-PEAK Buzzer ON LiPo BALANCE LiFe • Always disconnect the battery after charging, and let the charger cool between correctly can result in damage to the product, personal property and cause Pb BATT 2.0A 2.0V (1P) 2 PROGRAM 2.0A 22.2V(6S) NiCd Auto CHARGE LiIo CHARGE 2.0A 19.8V(6S) Pb DISCHARGEPB LiPo CHARGE 14 Li-Po BATTERIES PROGRAM SELECT SELECT NiMH CYCLE BATT TYPE LiFe DISCHARGE Lithium Batteries (Li-Po) charges. Input Power Low serious injury. CURRENT2.0A 2.0A 2.0A 21.6V(6S) 2.0A 2.0V 32 (1P) 22.2V(6S)1 Pb BATT 15 SYSTEM Li-Po Balance Charging Pb BATTERIES SET-> DCHG>CHG LiPo 2.0A 19.8V(6S) NiMH CYCLE Pb DISCHARGE Cut-Off 11.0V LiPo CHARGE LiFe DISCHARGE • Always charge in a well-ventilated area. 16 Li-Po Charging 33 Pb Charging This is a sophisticated hobby product. It must be operated with caution and common • Always terminate all processes and contact Horizon Hobby if the product DCHG>CHG 1 PROGRAM SELECT 2.0A 2.0V (1P) 2.0A 22.2V(6S) NiCd DISCHARGE LiIo FAST CHG 2.0A 19.8V(6S) PROGRAM SELECT LiPo FAST CHG PROGRAM SELECT Rest Time Ext. Temp NiCd BATT LiIo BALANCE 0.1A BATT CUT:VOLTS 1.0V NiCd CHARGE 2.0A 21.6V(6S) sense and requires some basic mechanical ability. Failure to operate this Product 17 Li-Po Fast Charging 34 0C Pb Discharge LiIo BATT 2.0A 22.2V(6S) LiPo BATT malfunctions. CHG>DCHG 7.4V(2S) Int. Temp 10min 32C LiPo FAST CHG PROGRAM SELECT 2.0A 21.6V(6S) CURRENT 2.0A Battery Memory LiIo BALANCE NiCd CHARGE Rest Time in a safe and responsible manner could result in injury or damage to the product or 2.0A 22.2V(6S) NiCd RE-PEAK LiIo STORAGE LiPo BATT LiPo STORAGE WARNING: Never leave charger unattended, exceed maximum charge rate, 2.0A 21.6V(6S) CURRENT 2.0A CHG>DCHG SAFETY TIMER SET CHARGE CURRENT SELF TEST AND PROGRAM SELECT SCREENS other property. This product is not intended for use by children without direct adult LOAD FACTORY NiCd10min Auto LiIo CHARGE 2 CHARGE 2.0A 21.6V(6S) 2.0A 22.2V(6S) charge with non-approved batteries or charge batteries in the wrong mode. ON 120min 2.2A LiPo STORAGE ENTER supervision. Do not attempt disassembly, use with incompatible components or CURRENT 2.0A 2.0A CHARGE 21.6V(6S) NiCd Auto CHARGE LiIo SAFETY TIMER When the charger is powered ON, there is a series of self tests and the screen will After the self tests, the charger will show another screen. The information on this Failure to comply may result in excessive heat, fire and serious injury. 2.0A 22.2V(6S) NiCd CYCLE LiIo DISCHARGE LiPo DISCHARGE augment product in any way without the approval of Horizon Hobby, Inc. This manual CURRENT 2.0A 2.0A 21.6V(6S) ON 120min PROGRAM SELECT Capacity Cut-Off DSCH CURRENT show the charger brand name and model number. screen will vary but will look similar to this: VERSION PROGRAM SELECT NiCd DISCHARGE LiIo FAST CHG DCHG>CHG 1 1.0A 21.6V(6S) PROGRAM SELECT2.0A 2.0A 22.2V(6S) contains instructions for safety, operation and maintenance. It is essential to read and BATT MEMORY ON 5000mAh LiPo DISCHARGE 1.00 CAUTION: Always ensure the battery you are charging meets the NiCd BATT 0.1A CUT: 1.0V 2.0A 21.6V(6S) LiIo BATT PROGRAM SELECT NiCd DISCHARGE LiIo FAST CHG Capacity Cut-Off PROGRAM SELECT follow all the instructions and warnings in the manual, prior to assembly, setup or use, 2.0A 22.2V(6S) LiPo BALANCE specifications of this charger and that the charger settings are correct. Not NiCd BATT Pb CHARGE 0.1A CUT: 1] 1.0V 2.0A 21.6V(6S) LiPo BALANCE ON 5000mAh [BATT MEMORY LiIo BATT Key Beep DSCH VOLTAGE in order to operate correctly and avoid damage or serious injury. NiCd RE-PEAK LiIo STORAGE 0.00 0.00 0.00 VON When Using an External AC Power Source: Getting Started 2.0A 2.0VENTER (1P) 2.0A 22.2V(6S) SET ->2 doing so can result in excessive heat and other related product malfunctions, Buzzer ON 3.0V/CELL 2.0A7.4V(2S) PROGRAM SELECT 2.0A 21.6V(6S) [BATT MEMORY 1] 0.00 0.00 0.00 V LiIo STORAGE Key BeepNiCd RE-PEAK ON 1. Connect the AC power cord to the charger AC power input port. Age Recommendation: Not for children under 14 years. This is not a toy. PROGRAM SELECT which can lead to user injury or property damage. Please contact Horizon Pb BATT CAUTION: Never connect the AC and DC input cords to an active power PROGRAM SELECT ENTER SET -> Pb DISCHARGE 2 2.0A 21.6V(6S) LiPo CHARGE Buzzer ON BATT TYPE TVC=YOUR RISK! Input Power Low LI BATT METER From any screen, press the Mode key to go back to the main menu. 2. Connect the AC power cord to the AC power source. NiCd LiFe BALANCE NiMH LiIo DISCHARGE Hobby or an authorized retailer with compatibility questions. Safety Precautions and Warnings MAIN 00.00V 11.0V SYSTEM SET-> source at the same time. This will void the warranty, cause product 2.0A 2.0VCYCLE (1P) 4.20V1 2.0A CHARGE 22.2V(6S) LiPo Cut-Off 3. Power ON the charger with the power switch. PROGRAM SELECT DCHG>CHG 2.0A 19.8V(6S) CURRENT 2.0A 2.0A 21.6V(6S) BATT TYPE H0.000V L0.000V NiCd CYCLE LiIo DISCHARGE Input Power Low Ni-Mh Batteries damage and possibly injure the user. NiMH CHARGE Li-Fe BATTERIES WARNING: Failure to exercise caution while using this product and comply 4. When the charger is powered ON, a message will appear on LiFe the LCD BALANCE screen. LiPo DCHG>CHG 1 2.0A 21.6V(6S)SYSTEM SET-> FAST CHG2.0A Cut-Off 11.0V SELECT BATT VOLTS TEMPERATURE Ext. Temp 0C Rest Time NiMH Auto CHARGE LiFe CHARGE 2.0A 19.8V(6S) PROGRAMLiPo CURRENT with the following warnings could result in product malfunction, electrical Pb CHARGE LiPo BALANCE 2.0A 22.2V(6S) BATT When Using an External DC Power Source: 7.4V(2S) CUT-OFF 50C Int. Temp 32C Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to CAUTION: Always power ON the charger before connecting a battery, or19.8V(6S) CHG>DCHG 10min CURRENT 2.0A 2.0A BCD BATT VOLTS A. A Li-Fe battery pack is Ext. Temp 0C 2.0A 2.0V (1P) 2.0A 22.2V(6S) PROGRAM SELECT issues, excessive heat, FIRE, and ultimately injury and property damage. Pb CHARGE LiPo BALANCE 1. Connect the DC power cord to the charger DC power input port. CHARGE Auto CHARGE LiFe BALANCE NiMH CHARGE locate the PROGRAM SELECT LiFe LOAD BATT screen. Press the SET Jog Dial to select LiFe. damage to the charger and the battery can result. 7.4V(2S) LiPo DISCHARGE STORAGE Int. Temp 32C CHARGE CURRENT SAVE PROGRAM balance charging FACTORY 2.0A 2.0V (1P) 2.0A 22.2V(6S) SAFETY TIMER Pb BATT LiFe FAST CHG NiMH PROGRAM SELECT 2.0A 19.8V(6S) CURRENT 2.0A PROGRAM SELECT 2. Connect the DC alligator clips to the DC power source. PROGRAM SELECT • Never leave the power supply, charger and battery unattended during use. LI 3S 2.0A 12.59V Pb DISCHARGE LiPo CHARGE 2.0A 22.2V(6S) 2.2A ENTER ENTER B. B attery pack has 3 cells in Rotate the Jog Dial to go to one of the control screens (BALANCE, CHARGE, FAST A ON 120min 2.0A 19.8V(6S) 0.1A CUT:1.0V NiMH BATT CHARGE CURRENT LiFe BATT 1. Connect the charger to the power source. Pb BATT LOAD FACTORY SET 3. Power ON the charger with the power switch. 2.0A 2.0V (1P) 2.0A 22.2V(6S) • Never attempt to charge dead, damaged or wet battery packs. Pb DISCHARGE LiPo CHARGE BAL 022:43 01082 series FAST CHG DISCHARGE PROGRAM SELECT LiFe CHARGE NiMH Auto CHARGE CHG, STORAGE or DISCHARGE) to do what your battery needs. 2.2A PROGRAM SELECTCapacity LiPo DISCHARGE DSCH CURRENT ENTER 2. Power ON the charger.PROGRAM SELECT VERSION 4. When the charger is powered ON, a message will appear on the LCD screen. 2.0A 2.0V (1P) 2.0A 22.2V(6S) NiMH RE-PEAK Cut-Off LiFe STORAGE 0.1A CUT:1.0V NiMH BATT 2.0A 19.8V(6S) 2.0A CHG LiFe BATT BATT MEMORY LiPo FAST 2.0A 22.2V(6S) SELECTCURRENT 1.0A Correctly connect your lithium battery to the charger (charging connector first and F E 1.00 3. Make program selections in the charger for battery charging.2.0A Rest Time over-temperature protection 2 ON 5000mAh SELECT LiPo 19.8V(6S) PROGRAMPROGRAM DSCH CURRENT NOTICE: Always connect cable polarities correctly. VERSION Included Items 2.0A 22.2V(6S) BATT LiPo FAST CHG PROGRAM SELECT RE-PEAK balancing connector second). Press the Jog Dial and adjust charging parameters STORAGE LiFe FAST CHG NiMH DISCHARGE PROGRAM SELECT C. Charging rate is 2.0A (2000mAh) 4. Connect the charger adapters to the charger. PROGRAM SELECT CHG>DCHG 10min BATT MEMORY • Storage and Fast Charge modes Rest Time 1.0A 1.00 DSCH VOLTAGE NOTICE: Always consult 12V battery collateral materials or Horizon Hobby before [BATTCYCLE MEMORY 1] 22.2V(6S) 2.0A NiMH Key Beep ON 10min LiPo BATT 2 0.00 0.00 V LiFe DISCHARGE 2.0A 19.8V(6S) 0.1A CUT:1.0V NiMH BATT LiFe BATT as needed. Press and hold the Jog0.00 Dial (approximately 3 seconds) until the screen D. Voltage being applied to the battery is currently 12.59V 5. Connect the battery to the charger adapters (connect main charging CHG>DCHG JST_XH Balance adapter (2) LiPo STORAGE • User battery data, store and load up to 10 battery profiles 3.0V/CELL ENTER SET -> TIMER DCHG>CHG 1 Buzzer SAFETY ON 0.00 sequence. 0.00 0.00 V using with sources other than a standard AC wall outlet. 2.0A 19.8V(6S) DSCH VOLTAGE PROGRAM changes toSELECT start the battery check/charge E. Present charge level of the battery is 1082mAh connectors before connecting cell-balancing connectors, where used).STORAGE 2.0A 22.2V(6S) 0.00 0.00 0.00 V LiPo STORAGE • (2) 2x16 backlit, blue LCD CYCLE NiMH RE-PEAK ™ DISCHARGE LiFe ON 120min Banana plug to EC3 battery connector (2) SAFETY TIMER 3.0V/CELL TVC=YOUR RISK! LI BATT METER PROGRAM SELECT SELECT F. Time elapsed since the charge process started is 22:43 (22 minutes and 43 6. Start battery charging. BATT TYPE 0.00 0.00 V 2.0A 22.2V(6S) Input0.00 Power Low DCHG>CHG 1 PROGRAM A 2 MAIN 00.00V When the charge cycle starts, the • Insulated, color coded, banana jack, power output terminals (Red = Positive (+), 2.0A BALANCE 19.8V(6S) ON 120min LiIo NiCd CHARGE LiPo DISCHARGE 4.20V SYSTEM SET-> LiPo Cut-OffCapacity 11.0VCut-Off AC power cord (one region-US, EU, AU or UK) H0.000V L0.000V TVC=YOUR RISK! seconds) LI BATT METER charger compares the battery to the Black = Common or Negative (–)) 2.0A 21.6V(6S) CURRENT 2.0A 2.0A 22.2V(6S) LiPo DISCHARGE MAIN 00.00V NiMH CYCLE LiFe BALANCE DISCHARGE ON 5000mAh R: 3SER S:3SER 4.20V Capacity Cut-Off LiIo TEMPERATURE System Set NiCd CHARGE charger settings. The screen will show • Internal cooling fans with grill covers BATT VOLTS 2.0A 22.2V(6S) H0.000V L0.000V Optional Accessories Ext. Temp 0C DCHG>CHG 1 2.0A CHARGE 19.8V(6S) During charging, the Jog Dial can be rotated counterclockwise to show several ON Beep A. Power Output Red (+) NiCd Auto CHARGE LiIo 2.0A 21.6V(6S) CUT-OFF 50C CURRENT 2.0A Ni-Cd Batteries CONFIRM(ENTER) the battery and your settings • Operating temperature range of 0°C to +50°C MEMORY 1] 7.4V(2S) Key ON Int. Temp 32C5000mAh TEMPERATURE DYN4012 - DC Power Cord CURRENT[BATT 2.0A 2.0A 21.6V(6S) parameter messages on the LCD screen, including: End Voltage, Input Power VoltB. Power Output Black (–) ENTER SET -> Buzzer ON information. If the information after R: (charger) and S: (settings) (A) does not match, • Meets IP33CW, IK07 environmental specs [BATT MEMORY 1] CUT-OFF 50C Key Beep NiCd Auto CHARGE CHARGE SAVE PROGRAM LiIo BALANCE CHARGE DYN5031 - Insulated Charge Adapter, Banana to EC3 Device CHARGE CURRENT age, External & Internal Temperature, Temperature Cutoff, Safety Timer Status and C. Balance Circuit Adapter LOAD FACTORY SET ENTER ENTER SET -> PROGRAM SELECT press the Mode key and change the lithium battery charging parameters as Buzzer ON • Rugged industrial plastic case NiCd DISCHARGE LiIo FAST CHG CURRENT 2.0A PROGRAM SELECT 2.0A 21.6V(6S) DYN5032 - Balancing Adapter Board PROGRAM SELECT K. BATT TYPE 2.2A Input Power Low ENTER SAVE Capacity Cutoff. Board Connector NiCd BATT 0.1A PROGRAM CUT: 1.0V 2.0A 21.6V(6S) LiIo BATT needed. If the R: information matches S:, press the Jog Dial to confirm. After SYSTEM SET-> DYN5033 - Temperature Sensor: DYN4103, DYN4300 Specifications LiPo PROGRAM SELECT Cut-Off BATT TYPE ENTER Input Power11.0V Low PROGRAM SELECT SELECT NiCd CURRENT DISCHARGE Auto CHARGE CHG LiIo FAST CHARGE PROGRAM SELECT D. Temperature Probe Connection PROGRAM Rotate the Jog Dial clockwise to show the charge voltages for each cell. Press the DSCH confirmation, charging starts and information will show on the LCD screen VERSION SYSTEM SET-> LiPo Cut-Off 11.0V NiCd BATT NiCd RE-PEAK LiIo STORAGE 0.1A CUT:VOLTS 1.0V CURRENT 2.0A 2.0A 21.6V(6S) LiIo BATT Minimum computer requirements for use of included software: Microsoft® J. E. Mode/Stop Key AC Input Voltage 100–240V AC (50/60Hz) BATT MEMORY 1.0A BATT Ext. Temp 0C Jog Dial at any time to return to the Charge Monitor screen. The charger signals 1.00 (information may vary). ® ® ® 2 2.0A 21.6V(6S) Windows XP , Windows 7 or Windows Vista operating system, Compact disk (CD) F. USB Communications Port 7.4V(2S) Int. 32C BATT VOLTS Ext. Temp 0C when the charging (or discharging) process is complete (if Buzzer is set to ON). PROGRAM SELECT NiCd VOLTAGE RE-PEAK DISCHARGE LiIo STORAGE FAST CHG PROGRAM SELECT DC Input Voltage 11–18V DC DSCH reader capable of reading a mini-CD and USB 2.0 port. G. 1A USB Charge Port 0.00 0.00 0.00 V Int. Temp 32C NiCd NiCd BATT LiIo DISCHARGE 27.4V(2S) 0.1A CYCLE CUT: 1.0V 2.0A 21.6V(6S) LiIo BATT CHARGE CURRENT 3.0V/CELL LOAD FACTORY SET Charge Current 0.10 to 10.0A per channel (in 0.1A increments/200W CAUTION: The Li-Fe program menus are to be used ONLY for the 0.00 0.00 0.00 V H. Jog Dial DCHG>CHG 1 PROGRAM 2.0A 21.6V(6S) FEATURES SELECT 2.2A ENTER CHARGE LOAD FACTORY SET NiCd CYCLE DISCHARGE RE-PEAK LiIo STORAGE maximum per channel/400W Total) charging and discharging of Li-Fe battery packs. The charging of other TVC=YOUR RISK!CURRENT I. LCD Screen LI BATT METER • Two charging ports to charge two batteries at once. Batteries can be different 2.2A MAIN 00.00V ENTER DCHG>CHG 12 2.0A 21.6V(6S) PROGRAM SELECTPb CHARGE DSCH4.20V CURRENT LiPo BALANCE VERSION J. AC Power Input Port battery types using these programs will result in damage to the battery or Discharge Current 0.10 to 5.0A per channel (in 0.1A increments/25W capacities and cell counts H0.000V L0.000V 1.00 BATT MEMORY 2.0A 2.0VCURRENT (1P) 1.0A 2.0A DISCHARGE 22.2V(6S) PROGRAMPROGRAM SELECT DSCH SELECT VERSION K. Power Switch NiCd CYCLE LiIo charger. • 1A USB charge port compatible with iPhone®, iPod® or similar products maximum per channel/50W Total) TEMPERATURE Pb CHARGE LiPo BALANCE 1.0A Lithium Battery Meter Pb BATT MEMORY 1.00 DCHG>CHG 1 2.0A 21.6V(6S) L. DC Power Input/ • 100–240V AC (50/60Hz) or 11–18V DC input voltage Pb Batteries CUT-OFF 50C Pb DISCHARGE LiPo CHARGE 2.0A 2.0VVOLTAGE (1P) DSCH 2.0A 22.2V(6S) Operating temperature 0°C to +50°C CAUTION: Using a charge rate that is not compatible with the battery PROGRAM SELECT 0.00 0.00 0.00 V APP Connectors 2.0A 2.0VVOLTAGE (1P) 2.0A 22.2V(6S) • Li-Ion/Li-Po/Li-Fe battery cell count of 1 to 6 series cells 3.0V/CELL DSCH Pb BATT capacities may result in damage or malfunction of the charger or 0.00 0.00 0.00 V Balance Current Drain 300mA per cell SAVE PROGRAM DISCHARGE Pb CHARGE CHARGE PROGRAM SELECT LiPo BALANCE • Ni-Cd/Ni-MH battery cell count of 1 to 15 cells 3.0V/CELL batteries. 0.00 0.00 0.00 V TVC=YOUR RISK! LiPo FAST CHG 2.0A Time 2.0VENTER (1P) PROGRAM SELECT LI BATT METER 2.0A 22.2V(6S) PROGRAM SELECT PROGRAM SELECT Trickle Charge Current 50 to 200mA Rest MAIN 00.00V • Pb battery voltage of 2 to 20V 4.20V 2.0A 22.2V(6S) LiPo BATT TVC=YOUR RISK! LI BATT METER Pb BATT CHG>DCHG 10min H0.000V L0.000V MAIN 00.00V • Built-in 50W discharger CHG Pb DISCHARGE LiPo FAST CHARGE PROGRAM SELECT Charging Mode Peak (Ni-Cd/Ni-MH), CC/CV (Li-Po/Li-Ion/Li-Fe/Pb) 4.20V Rest TEMPERATURE H0.000V L0.000V LiPo L. 2.0A Time 2.0V (1P) 2.0A 22.2V(6S) A. LiPo B. BATT H. C. I. D. E. F. STORAGE G. • Built-in balance circuit SAFETY TIMER CHG>DCHG 10min CUT-OFF 50C 2.0A 22.2V(6S) TEMPERATURE • Short-circuit, over-current, reverse polarity, low input voltage and ON 120min STORAGE LiPo FAST CHG PROGRAM SELECT CUT-OFF SAFETY TIMER Rest Time SAVE PROGRAM 50C LiPo DISCHARGE 2.0A 22.2V(6S) LiPo BATT Capacity Cut-Off ON 120min CHG>DCHG 10min 2.0A 22.2V(6S) SAVE PROGRAM ON 5000mAh ENTER DISCHARGE LiPo STORAGE Capacity Cut-Off ENTER SAFETY TIMER 2.0A 22.2V(6S) Li-Fe Balance Charging Li-Fe DischargING Li-Io Charging Li-Po BATTERIES [BATT MEMORY 1] Key Beep 5000mAh ON ON 120min ENTER SET -> Buzzer ON LiPo DISCHARGE Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to To select values other than the existing parameters: [BATT MEMORY 1] Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to To select values other than the existing parameters: Key Beep Cut-Off ON Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to Capacity Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to To select values other than the existing parameters: BCD A. A Li-Po battery pack is 2.0A TYPE 22.2V(6S) SELECT SETlocate -> the PROGRAM Input Power Low Buzzer PROGRAM SELECT LiIo BATT screen. Press Dial5000mAh to go intoON this ON the Jog locate the PROGRAM SELECT LiFe BATT screen. Press the Jog Dial to go into this • Press the Jog Dial so the charge current value (A) flashes locate the PROGRAM SELECT LiPo BATT screen. Press the Jog Dial to select LiPo. • Press the Jog Dial so the charge current value (A) flashes locate the PROGRAM SELECT LiFe BATT screen. Press the Jog Dial to go into this • Press the Jog Dial so the discharge current value (A) flashesBATT ENTER balance charging SYSTEM SET-> LiPo Cut-Off 11.0V menu. PROGRAM SELECT menu. • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value menu. • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value Rotate the Jog Dial to go to one of the control screens (BALANCE, CHARGE, FAST BATT [BATT MEMORY 1] A LI 3S 2.0A 12.59V B. B attery pack has 3 cells in Input Power LowON Key Beep • Rotate the Jog Dial to INCREASE OR DECREASE the discharge currentTYPE value SYSTEM to go to theSET-> LiIo CHARGE screen and set charging11.0V parameters. • Press the Jog Dial to save the value and the voltage value (B) flashes BATT BAL 022:43 01082 series ENTER SETRotate -> the Jog Dial Rotate the Jog Dial to go to the LiFe BALANCE screen and set charging param• Press the Jog Dial to save the value and the voltage value (B) flashes Ext. Temp 0C Cut-Off Buzzer ON CHG, STORAGE or DISCHARGE) to do what your battery needs. Rotate the Jog Dial to go to the LiFe DISCHARGE screen and set discharging pa• Press the Jog Dial to save the value and the voltage value (B)LiPo flashesVOLTS 7.4V(2S) Int. TempVoltage (B) 32C The charging amperage can be set between 0.1 and 10.0A. is • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in eters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in rameters. The discharging amperage (A) can be set between 0.1 and 5.0A. Voltage • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of VOLTS cells in Correctly connect your lithium battery to the charger (charging connector first and F E PROGRAM (A) SELECT TYPE BATT Ext. Temp 0C Input Power Low dependent on the number of cells in series. For example, with Li-Io batteries these series (C)) dependent on the number of cells in series. For example, with Li-Fe batteries these series (C)) (B) is dependent on the number of cells in series. For example, with Li-Fe batteries series (C)) SYSTEM SET-> CHARGE balancing connector second). Press the Jog Dial and adjust the charging paramLiPo CURRENT 7.4V(2S) LOAD FACTORY SET Int. Temp 32C C. Charging rate is 2.0A (2000mAh) Cut-Off 11.0V values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries). • Press the Jog Dial to save the voltage value values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries). • Press the Jog Dial to save the voltage value 2.2A these values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries). • Press the Jog Dial to save the voltage value ENTER eters as needed. Press and hold the Jog Dial (approximately 3 seconds) until the D. Voltage being applied to the battery is currently 12.59V CHARGE CURRENT BATT VOLTS LOAD FACTORY SET Ext. Temp 0C If no parameters are flashing, you can rotate the Jog Dial to select another program If no parameters are flashing, you can rotate the Jog Dial to select another program screen changes to start the battery check/charge sequence. E. Present charge level of the battery is 1082mAh A battery’s capacity can be verified by discharging it to its minimum voltage level If no parameters are flashing, you can rotate the Jog Dial to select another program PROGRAM SELECT DSCH CURRENT 2.2A 7.4V(2S) VERSION Int. Temp ENTER 32C such as BALANCE, FAST CHG, STORAGE or DISCHARGE. such as CHARGE, FAST CHG, STORAGE or DISCHARGE. F. Time elapsed since the charge process started is 22:43 BATT MEMORY A and measuring the current as the battery is discharged. such as CHARGE, BALANCE, FAST CHG or STORAGE. 1.0A When the charge cycle starts, the 1.00 PROGRAM SELECT DSCH CURRENT CHARGE CURRENT VERSION LOAD FACTORY SET To start charging, press and hold the Jog Dial for 3 seconds. To start charging, press and hold the Jog Dial for 3 seconds. charger compares the battery to the To start discharging, press and holdBATT the JogMEMORY Dial for 3 seconds. DSCH VOLTAGE1.0A During charging, the Jog Dial can be rotated counterclockwise to show several 2.2A 1.00 ENTER R: 3SER S:3SER charger settings. The screen will show parameter 0.00 0.00 0.00 V messages on the LCD screen, including: End Voltage, Input Power VoltCAUTION: If at any time during the charge process the battery pack becomes 3.0V/CELL 0.00 0.00 0.00 V CONFIRM(ENTER) the battery and your settings PROGRAM SELECT DSCH VOLTAGE CURRENT PROGRAM SELECT VERSION age, External & Internal Temperature, Temperature Cutoff, Safety Timer Status and hot or begins to puff, disconnect the battery immediately and discontinue the 0.00 0.00 0.00 V TVC=YOUR RISK! BATT MEMORY 3.0V/CELL 1.0A LI BATT METER B information. If the information after R: (charger) and S: (settings) (A) does not match, Capacity Cutoff. MAIN 0.00 00.00V 0.00 0.00 V charge process as batteries can cause fire, collateral damage and injuries. C 1.00 A B C PROGRAM SELECT 4.20V A press the Mode key and change the lithium battery charging parameters as H0.000V L0.000V TVC=YOUR RISK! DSCH VOLTAGE LI BATT METER Rotate the Jog Dial clockwise to show the charge voltages for each cell. Press the MAIN 00.00V 0.00 0.00 0.00 V needed. If the R: information matches S:, press the Jog Dial to confirm. TEMPERATURE 4.20V 3.0V/CELL Jog Dial at any time to return to the Charge Monitor screen. The charger signals H0.000V L0.000V 0.00 0.00 0.00 V Li-Fe Charging Fast Charging A B C PROGRAM SELECT CUT-OFF 50C Li-Io After confirmation, charging starts and information will show on the LCD screen when the charging (or discharging) process is complete (if Buzzer is set to ON). TEMPERATURE TVC=YOUR RISK! LI BATT METER MAINthen 00.00V (information may vary). Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to To select values other than the existing parameters: Press rotate the Jog Dial to SAVE PROGRAM CUT-OFF 50Cthe Mode key until you reach the 9 main menus, 4.20V H0.000V CAUTION: The Li-Po program menus are to be used ONLY for the locate the PROGRAM SELECT LiFe BATT screen. Press the Jog Dial to go into this • Press the Jog Dial so the charge current value (A) flashes locate the PROGRAM SELECT LiIo BATT screen. Press the Jog DialL0.000V to go into this ENTER SAVE PROGRAM menu. TEMPERATURE menu. charging and discharging of Li-Po battery packs. The charging of other • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value ENTER CUT-OFF 50C battery types using these programs will result in damage to the battery or Rotate the Jog Dial to go to the LiFe CHARGE screen and set charging parameters. • Press the Jog Dial to save the value and the voltage value (B) flashes Rotate the Jog Dial to go to the LiIo FAST CHG screen and set charging param Li-Io BATTERIES charger. SAVE PROGRAM eters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is ENTER series (C)) dependent on the number of cells in series. For example, with Li-Fe batteries these dependent on the number of cells in series. For example, with Li-Io batteries these CAUTION: Using a charge rate that is not compatible with the battery 1 JST_XH ADAPTER 2S 3S 4S JST_XH ADAPTER 5S 6S 2S 3S 4S 5S 6S DYNAMITE DYN4300 2 3 7 LiFe BALANCE 5.5A19.8V(6S) 10 LiIo CHARGE 4.6A21.6V(6S) LiFe DISCHARGE 2.0A19.8V(6S) 4 14 11 LiIo FAST CHG 5.0A21.6V(6S) 8 values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries). LiFe CHARGE 4.6A19.8V(6S) A 5 B C 6 AUTION: If at any time during the charge process the battery pack becomes C hot or begins to puff, disconnect the battery immediately and discontinue the charge process as batteries can cause fire, collateral damage and injuries. LiFe FAST CHG 0.1A19.8V(6S) A B C To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, BALANCE, STORAGE or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. Li-Fe Storage Charging Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiFe BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiFe STORAGE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Fe batteries these values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries). If you don’t plan on using your battery for a long time, it is best to charge (or discharge) the battery to its optimal storage voltage and capacity. LiFe STORAGE 2.5A19.8V(6S) A B C Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiIo BATT screen. Press the Jog Dial to select LiIo. Rotate the Jog Dial to go to one of the control screens (BALANCE, CHARGE, FAST CHG, STORAGE or DISCHARGE) to do what your battery needs. Correctly connect your lithium battery to the charger (charging connector first and balancing connector second). Press the Jog Dial and adjust the charging parameters as needed. Press and hold the Jog Dial (approximately 3 seconds) until the screen changes to start the battery check/charge sequence. A When the charge cycle starts, the charger compares the battery to charger settings. The screen will show the battery and your settings information. If the information after R: (charger) and S: (settings) (A) does not match, press the Mode key and change the lithium battery charging parameters as needed. If the R: information matches S:, press the Jog Dial to confirm. After confirmation, charging starts and information will show on the LCD screen (information may vary). R: 3SER S:3SER CONFIRM(ENTER) Li-Fe Fast Charging Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiFe BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiFe FAST CHG screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Fe batteries these values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries). Near the end of a standard charging cycle, the charger switches from Constant Current (CC) mode to Constant Voltage (CV) mode to slowly “top off” the current in the battery as close as possible to the maximum capacity. In Fast Charge, the CV mode is eliminated in order to greatly shorten the charging time; however, the final capacity of the battery will be less than what you would get using the standard charge method. • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as BALANCE, FAST CHG, STORAGE or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, BALANCE, FAST CHG or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. BCD A LI 3S 2.0A 12.59V BAL 022:43 01082 A. A Li-Io battery pack is balance charging B. Battery pack has 3 cells in series F E C. Charging rate is 2.0A (2000mAh) D. Voltage being applied to the battery is currently 12.59V E. Present charge level of the battery is 1082mAh F. Time elapsed since the charge process started is 22:43 During charging, the Jog Dial can be rotated counterclockwise to show several parameter messages on the LCD screen, including: End Voltage, Input Power Voltage, External & Internal Temperature, Temperature Cutoff, Safety Timer Status and Capacity Cutoff. Rotate the Jog Dial clockwise to show the charge voltages for each cell. Press the Jog Dial at any time to return to the Charge Monitor screen. The charger signals when the charging (or discharging) process is complete (if Buzzer is set to ON). AUTION: The Li-Io program menus are to be used ONLY for the charging C and discharging of Li-Io battery packs. The charging of other battery types using these programs will result in damage to the battery or charger. CAUTION: Using a charge rate that is not compatible with the battery capacities may result in damage or malfunction of the charger or batteries. 9 values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries). Near the end of a standard charging cycle, the charger switches from Constant Current (CC) mode to Constant Voltage (CV) mode to slowly “top off” the current in the battery as close as possible to the maximum capacity. In Fast Charge, the CV mode is eliminated in order to greatly shorten the charging time; however, the final capacity of the battery will be less than what you would get using the standard charge method. 12 Li-Io Balance Charging A LiIo BALANCE 5.5A21.6V(6S) A B C To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, FAST CHG, STORAGE or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. B C Li-Io Storage Charging Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiIo BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiIo STORAGE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Io batteries these values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries). If you don’t plan on using your battery for a long time, it is best to charge (or discharge) the battery to its optimal storage voltage and capacity. LiIo STORAGE 2.5A21.6V(6S) Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiIo BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiIo BALANCE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Io batteries these values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries). A To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, BALANCE, STORAGE or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. 13 B To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, BALANCE, FAST CHG or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. Li-Io DischargING LiIo DISCHARGE 2.0A21.6V(6S) A B C 15 Li-Po Balance Charging Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiPo BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiPo BALANCE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Po batteries these values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries). LiPo BALANCE 5.5A22.2V(6S) A B To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, FAST CHG, STORAGE or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. C 16 Li-Po Charging C Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiIo BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiIo DISCHARGE screen and set discharging parameters. The discharging amperage (A) can be set between 0.1 and 5.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Io batteries these values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries). A battery’s capacity can be verified by discharging it to its minimum voltage level and measuring the current as the battery is discharged. capacities may result in damage or malfunction of the charger or batteries. To select values other than the existing parameters: • Press the Jog Dial so the discharge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the discharge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, BALANCE, FAST CHG or STORAGE. To start discharging, press and hold the Jog Dial for 3 seconds. Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiPo BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiPo CHARGE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Po batteries these values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries). LiPo CHARGE 4.6A22.2V(6S) A B C To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as BALANCE, FAST CHG, STORAGE or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. AUTION: If at any time during the charge process the battery pack becomes C hot or begins to puff, disconnect the battery immediately and discontinue the charge process as batteries can cause fire, collateral damage and injuries. 17 24 Li-Po Fast Charging Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiPo BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiPo FAST CHG screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Po batteries these values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries). Near the end of a standard charging cycle, the charger switches from Constant Current (CC) mode to Constant Voltage (CV) mode to slowly “top off” the current in the battery as close as possible to the maximum capacity. In Fast Charge, the CV mode is eliminated in order to greatly shorten the charging time; however, the final capacity of the battery will be less than what you would get using the standard charge method. 18 LiPo FAST CHG 4.0A7.4V(2S) A B Li-Po Storage Charging Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiPo BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiPo STORAGE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Po batteries these values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries). If you don’t plan on using your battery for a long time, it is best to charge (or discharge) the battery to its optimal storage voltage and capacity. LiPo STORAGE 2.5A11.1V(3S) A 19 B To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, BALANCE, FAST CHG or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. Li-Po DischargING LiPo DISCHARGE 2.0A22.2V(6S) A B To select values other than the existing parameters: • Press Jog Dial so the discharge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the discharge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, BALANCE, FAST CHG or STORAGE. To start discharging, press and hold the Jog Dial for 3 seconds. A B C NiMH 2.0A 7.59V CHG022:43 01082 A. A Ni-MH battery pack is charging B. Charging rate is 2.0A (2000mAh) Ni-MH Cycle Charging Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiMH BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiMH CYCLE screen and set charge/discharge cycle count parameters. The battery can be put through a series of charge/discharge cycles using this program. Cycling Ni-MH batteries can increase capacity and rejuvenate neglected batteries. Discharge capacity and average battery voltage help you compare batteries for the best run time and power. A Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiCd BATT screen. Press the Jog Dial to select NiCd. Rotate the Jog Dial to go to one of the control screens (CHARGE, Auto CHARGE, DISCHARGE, RE-PEAK or CYCLE) to do what your battery needs. Correctly connect your Ni-Cd battery to the charger. Press the Jog Dial and adjust the charging parameters as needed. Press and hold the Jog Dial (approximately 3 seconds) until the screen changes to start the battery check/charge sequence. After confirmation, charging starts and information will show on the LCD screen (information may vary). A C NiCd 2.0A 7.59V CHG022:43 01082 A. A Ni-Cd battery pack is charging B. Charging rate is 2.0A (2000mAh) During charging, the Jog Dial can be rotated counterclockwise to show several parameter messages on the LCD screen, including: Ni-MH Sensitivity, Input Power Voltage, External & Internal Temperature, Temperature Cutoff, Safety Timer Status and Capacity Cutoff. The charger signals when the charging (or discharging) process is complete (if Buzzer is set to ON). AUTION: The Ni-MH program menus are to be used ONLY for the C charging and discharging of Ni-MH battery packs. The charging of other battery types using these programs will result in damage to the battery or charger. CAUTION: Using a charge rate that is not compatible with the battery capacities may result in damage or malfunction of the charger or batteries. NiCd CHARGE CURRENT1.0A NiMH CHARGE CURRENT1.0A A 22 28 NiMH Auto CHARGE CURRENT1.0A To select a value other than the existing parameter: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, DISCHARGE, RE-PEAK or CYCLE. To start charging, press and hold the Jog Dial for 3 seconds. NiMH DISCHARGE 0.1A CUT: 1.0V B To select a value other than the existing parameter: • Press the Jog Dial so the discharge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the discharge current value • Press the Jog Dial to save the value and the cutoff voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the cutoff voltage • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, Auto CHARGE, RE-PEAK or CYCLE. To start discharging, press and hold the Jog Dial for 3 seconds To select a value other than the existing parameter: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value If no parameters are flashing, you can rotate the Jog Dial to select another program such as Auto CHARGE, DISCHARGE, RE-PEAK or CYCLE. To start charging, press and hold the Jog Dial for 3 seconds. To select a value other than the existing parameter: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, DISCHARGE, RE-PEAK or CYCLE. To start charging, press and hold the Jog Dial for 3 seconds. 34 Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT Pb BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the Pb DISCHARGE screen and set discharging parameters. The discharging amperage (A) can be set between 0.1 and 5.0A. A battery’s capacity can be verified by discharging it to its minimum voltage level and measuring the current as the battery is discharged. The discharge level can be set from 2 to 20V. 35 29 Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiCd BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiCd DISCHARGE screen and set discharging parameters. The discharging amperage (A) can be set between 0.1 and 5.0A. A battery’s capacity can be verified by discharging it to its minimum voltage level and measuring the current as the battery is discharged. The discharge level can be set from 0.1 to 25.2V. NiCd DISCHARGE 0.1A CUT: 1.0V To select a value other than the existing parameter: • Press the Jog Dial so the discharge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the discharge current value • Press the Jog Dial to save the value and the cutoff voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the cutoff voltage • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, Auto CHARGE, RE-PEAK or CYCLE. To start discharging, press and hold the Jog Dial for 3 seconds AUTION: The Pb program menus are to be used ONLY for the charging C and discharging of Pb battery packs. The charging of other battery types using these programs will result in damage to the battery or charger. CAUTION: Using a charge rate that is not compatible with the battery capacities may result in damage or malfunction of the charger or batteries. 3.70 3.70 0.00 V 0.00 0.00 0.00 V 38 This example is for a 2S battery, so only the voltages for these two cells are displayed. The data is presented in this format: 1–1 1–4 1–2 1-5 1–3 V 1–6 V At this point, you can rotate the Jog Dial to see a display of the overall battery voltage as well as the individual high- and low-cell voltage values. MAIN08.20V H4.104VL4098V You may exit this menu at any time by pressing the Mode key to return to the main menus. USB ACCESSORY CHARGER OPERATION (COMPATIBLE WITH iPhone and iPod DEVICES) To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the charge current value and the battery voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the battery voltage/cell count value (Pb batteries are 2.0V per cell, for a 6 cell battery this would be 2.0V x 6 cell = 12.0V) • Press the Jog Dial to save the voltage If no parameters are flashing, you can rotate the Jog Dial to select another program such as DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. To select values other than the existing parameters: • Press the Jog Dial so the discharge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the discharge current value • Press the Jog Dial to save the value and the cutoff voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the cutoff voltage • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE. To start discharging, press and hold the Jog Dial for 3 seconds 39 Troubleshooting Guide LCD Screen Warning and Error messages shown below. During charger operation, circuits monitor battery and charger functions. If the following messages show on the charger’s LCD screen, make the recommended responses. If the message continues after you respond as recommended, contact your nearest Horizon Hobby customer service center for assistance. REVERSE POLARITY Make sure each connection polarity is correct between the power source and the charger, then between the charger and the battery CONNECTION BREAK Make sure the power connections are correct for charging SHORT ERR Make sure there are no short circuits between the poles of the battery or the battery and the charger. Replace damaged wires. INPUT VOL ERR Input voltage to the charger fell below the default or adjusted input voltage setting. Make sure the power source for the charger provides correct input voltage. VOL SELECT ERR Incorrect setting for cell in series count (pack voltage) of a lithium battery. Make charger settings match the battery pack label cell in series count specifications or replace the battery. BREAK DOWN Charger electronics require repair. BATTERY CHECK LOW VOLTAGE Battery voltage is lower than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery. BATTERY CHECK HIGH VOLTAGE Battery voltage is higher than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery. Battery Type Standard voltage (Volts per cell) Max. voltage (Volts per cell) Min. voltage (Volts per cell) Li-Po 3.70 4.20 3.00 Li-Io 3.60 4.10 3.00 Li-Fe 3.30 3.60 2.00 Ni-MH 1.20 1.60 1.00 Ni-Cd 1.20 1.60 0.85 Pb 2.00 2.45 1.75 Ni-CD Re-Peak Charging NiCd RE-PEAK 1 31 To select a value other than the existing parameter: • Press the Jog Dial so the re-peak value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the value • Press the Jog Dial to save the value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, Auto CHARGE, DISCHARGE or CYCLE. Press the Jog Dial to go to the next menu. Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiCd BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiCd CYCLE screen and set charge/discharge cycle count parameters. The battery can be put through a series of charge/discharge cycles using this program. Cycling Ni-Cd batteries can increase capacity and rejuvenate neglected batteries. Discharge capacity and average battery voltage help you compare batteries for the best run time and power. NiCd CYCLE CHG>DCHG5 B To select values other than the existing parameter: • Press the Jog Dial so the cycle type (A) flashes • Rotate the Jog Dial to set the cycle type as CHG>DCHG or DCHG>CHG • Press the Jog Dial to save your choice and the number of cycles (B) flashes • Rotate the Jog Dial to set the cycle count between 1 to 5 • Press the Jog Dial to save the cycle count value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, Auto CHARGE, DISCHARGE or RE-PEAK. To start cycling, press and hold the Jog Dial for 3 seconds. Rotate the Jog Dial to select SAVE PROGRAM Press the Jog Dial to save the program Repeat this process to enter additional battery profiles Press the Mode key until you reach the 9 main menus AUTION: Increasing the TVC value beyond the default settings may result in a C shorter battery life and/or damage to the battery. Do not change the TVC value unless you fully understand the effects TVC will have on your battery. To Charge or Discharge a battery using the saved profile: Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT BATT MEMORY screen. Press the Jog Dial to select BATT MEMORY. • Rotate the Jog Dial to identify the battery profile, 1 through 10. • Press and hold the Jog Dial for 3 seconds • Rotate the Jog Dial to choose the type of charge function you wish to perform • Press and hold the Jog Dial for 3 seconds to start SYSTEM SET Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT SYSTEM SET screen. Press the Jog Dial to select SYSTEM SET. Use this menu to set the “behind the scenes” operating parameters for this charger such as; Rest Time, Safety Timer, Capacity Cutoff, Key Beep/Buzzer, Input Power Low Cutoff, External and Internal Temperatures, Load Factory Settings and Version. d KEY BEEP/BUZZER e INPUT POWER LOW CUTOFF f EXTERNAL AND INTERNAL TEMPERATURES REST TIME Use this menu to set the Rest time during each step in a cycle.When a Ni-MH or Ni-CD battery is cycled (charged, discharged and charged again) it will get hot, therefore it is necessary to set a rest time interval during each step of the process to make sure the battery and charger are completely cooled before moving on to the next part of the cycle. Default time is 10 minutes, but this can be set between 1 and 60 minutes. To select a value other than the default parameter: • Press the Jog Dial to select Rest Time • Press the Jog Dial so the Rest Time value flashes • Rotate the Jog Dial to select Rest Time in Minutes • Press the Jog Dial to save the Rest Time value • Rotate the Jog Dial to select SAFETY TIMER Use this menu to set the key beep and charger alarm buzzer at ON or OFF as needed. We recommend that you keep the alarm ON so the alarm will sound when charging is complete or if there is cause for alarm during charging. To select values other than the default parameters: • Press the Jog Dial so the Key Beep ON/OFF value flashes • Rotate the Jog Dial to select ON or OFF • Press the Jog Dial to save the value • Press the Jog Dial so the Buzzer ON/OFF value flashes • Rotate the Jog Dial to select ON or OFF • Press the Jog Dial to save the value • Rotate the Jog Dial to select Input Power Low Cutoff SAFETY TIMER Use this menu to set a time limit for charging a battery. When a charge cycle is started, a clock inside the charger will begin recording the elapsed charge time. If the SAFETY TIMER function has been turned ON, the charger will stop the charging process once this time limit has been reached to avoid damage caused by over-charging the battery. This time value can be set between 1 and 720 minutes. To select values other than the default parameters: • Press the Jog Dial so the ON/OFF value flashes • Rotate the Jog Dial to select ON or OFF • Press the Jog Dial to save the value • Rotate the Jog Dial to select the value for time • Press the Jog Dial to save the value • Rotate the Jog Dial to select Capacity Cutoff CAPACITY CUTOFF c Ni-CD Cycle Charging • • • • 36 b B 30 A During charging, the Jog Dial can be rotated counterclockwise to show several parameter messages on the LCD screen, including: End Voltage, Capacity Cutoff, Safety Timer Status, Temperature Cutoff and Input Power Voltage. The charger signals when the charging (or discharging) process is complete (if Buzzer is set to ON). The Passport Ultra Duo charger has the capability to read and display the individual cell voltages of a Li-Po, Li-Fe or Li-Io battery. This voltage checking function can only be used when the charger is powered ON and not charging a battery. To use the voltage checker, connect the balance port connector of your Li-Po, Li-Fe or Li-Io battery to the balance adapter board connected to the Balance Circuit Adapter Board Connector (C). Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LI BATT METER screen. Press the Jog Dial to select LI BATT METER. In a few moments, the charger will begin to display the cell voltages of the battery in the following format: BATTERY MEMORY Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT BATT MEMORY screen. Press the Jog Dial to select BATT MEMORY. Use this menu to create a battery profile. To reduce the time required to initiate a charging or discharging cycle on a battery you regularly use, this charger has been designed with the capability of storing up to 10 battery profiles that can be quickly accessed and run at a later time. • Rotate the Jog Dial to identify a battery profile, 1 through 10 • Press the Jog Dial to select battery profile 1 • Press the Jog Dial so battery type flashes • Rotate the Jog Dial to select a battery type • Press the Jog Dial to save the battery type Follow this process using the Jog Dial to select, change, then save each parameter (battery voltage, charge current, discharge current, discharge voltage, Terminal Voltage Control (TVC) and temperature cutoff). Then save the battery profile. A F E C. Charging at a rate of 0.4A (400mAh) D. Voltage being applied to the battery is currently 12.39V E. Present charge level of the battery is 1082mAh F. Time elapsed since the charge process started is 22:43 Pb DischargING a Ni-CD DischargING Ni-MH DischargING Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiMH BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiMH DISCHARGE screen and set discharging parameters. The discharging amperage (A) can be set between 0.1 and 5.0A. A battery’s capacity can be verified by discharging it to its minimum voltage level and measuring the current as the battery is discharged. The discharge level can be set from 0.1 to 25.2V. A B Pb DISCHARGE 0.1A 2.0V (1P) A Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiCd BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiCd RE-PEAK screen and set re-peak parameters to a value of between 1 and 3. A 23 AUTION: The Ni-Cd program menus are to be used ONLY for the C charging and discharging of Ni-Cd battery packs. The charging of other battery types using these programs will result in damage to the battery or charger. CAUTION: Using a charge rate that is not compatible with the battery capacities may result in damage or malfunction of the charger or batteries. Ni-CD Auto Charging Ni-MH Auto Charging Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiMH BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiMH Auto CHARGE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Pb CHARGE 0.1A 2.0V (1P) parameter messages on the LCD screen, including: Ni-Cd Sensitivity, Input Power Voltage, External & Internal Temperature, Temperature Cutoff, Safety Timer Status and Capacity Cutoff. The charger signals when the charging (or discharging) process is complete (if Buzzer is set to ON). A Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiCd BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiCd Auto CHARGE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. To select a value other than the existing parameter: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value If no parameters are flashing, you can rotate the Jog Dial to select another program such as Auto CHARGE, DISCHARGE, RE-PEAK or CYCLE. To start charging, press and hold the Jog Dial for 3 seconds. Pb-60.4A12.39V CHG022:43 01082 A A. A Lead Acid battery pack is charging B. Battery pack has 6 cells in series A B Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiCd BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiCd CHARGE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. NiCd Auto CHARGE CURRENT1.0A Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiMH BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiMH CHARGE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT Pb BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the Pb CHARGE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. ED C. Voltage being applied to the battery is currently 7.59V D. Present charge level of the battery is 1082 mAh E. Time elapsed since the charge process started is 22:43 Ni-MH Charging A B CD Pb Charging B 26 B The Passport Ultra Duo charger has the capability to charge your iPhone, iPod or USB compatible device with the 1A USB charge port (E). To use the charging function, simply connect a compatible charging device or cord into the charge port while the charger is powered ON. The internal USB charge port will provide up to 1A current at 5V DC. 33 Ni-CD Charging ED C. Voltage being applied to the battery is currently 7.59V D. Present charge level of the battery is 1082 mAh E. Time elapsed since the charge process started is 22:43 21 To select values other than the existing parameter: • Press the Jog Dial so the cycle type (A) flashes • Rotate the Jog Dial to set the cycle type as CHG>DCHG or DCHG>CHG • Press the Jog Dial to save your choice and the number of cycles (B) flashes • Rotate the Jog Dial to set the cycle count between 1 to 5 • Press the Jog Dial to save the cycle count value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, Auto CHARGE, DISCHARGE or RE-PEAK. To start cycling, press and hold the Jog Dial for 3 seconds. NiMH CYCLE CHG>DCHG5 27 Ni-MH BATTERIES Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiMH BATT screen. Press the Jog Dial to select NiMH. Rotate the Jog Dial to go to one of the control screens (CHARGE, Auto CHARGE, DISCHARGE, RE-PEAK or CYCLE) to do what your battery needs. Correctly connect your Ni-MH battery to the charger. Press the Jog Dial and adjust the charging parameters as needed. Press and hold the Jog Dial (approximately 3 seconds) until the screen changes to start the battery check/charge sequence. After confirmation, charging starts and information will show on the LCD screen (information may vary). 25 37 Li BATTERY VOLTAGE CHECKER OPERATION - USING THE BALANCE ADAPTER PORT Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT Pb BATT screen. Press the Jog Dial to select Pb. Rotate the Jog Dial to go to one of the control screens (CHARGE or DISCHARGE) to do what your battery needs. The nature of a Lead Acid or Sealed Lead Acid battery is very different from that of Lithium, Ni-MH or Ni-Cd batteries. The output current of a Pb battery is lower than other batteries relative to their capacities. Furthermore, lead acid batteries can’t be charged at a level greater than 1/10 their capacity. For example, a 5000mAh lead acid battery can’t be charged at a rate greater than 0.5A. For more details on the charge and discharge capabilities of your battery, please refer to the charging data supplied by the battery manufacturer. Correctly connect your Pb battery to the charger. Press the Jog Dial and adjust the charging parameters as needed. Press and hold the Jog Dial (approximately 3 seconds) until the screen changes to start the battery check/charge sequence. After confirmation, charging starts and information will show on the LCD screen (information may vary). During charging, the Jog Dial can be rotated counterclockwise to show several C 20 NiMH RE-PEAK 1 To select a value other than the existing parameter: • Press the Jog Dial so the re-peak value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the value • Press the Jog Dial to save the value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, Auto CHARGE, DISCHARGE or CYCLE. Press the Jog Dial to go to the next menu. Ni-CD BATTERIES C Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiPo BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiPo DISCHARGE screen and set discharging parameters. The discharging amperage (A) can be set between 0.1 and 5.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Po batteries these values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries). A battery’s capacity can be verified by discharging it to its minimum voltage level and measuring the current as the battery is discharged. 32 Pb BATTERIES Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiMH BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiMH RE-PEAK screen and set re-peak parameters to a value of between 1 and 3. C To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial again to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, BALANCE, STORAGE or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. Ni-MH Re-Peak Charging Use this menu to set a capacity limit at which the charger will stop charging a battery. When a charge cycle starts, the charger records the battery capacity. When the Capacity Cutoff function is set at ON, the charger will stop charging at the capacity limit to prevent battery damage. Capacity can be adjusted between 100 and 50,000mAh. • Press the Jog Dial so the ON/OFF value flashes • Rotate the Jog Dial to select ON or OFF • Press the Jog Dial to save the value • Rotate the Jog Dial to select the Capacity Cutoff value • Press the Jog Dial to save the value • Rotate the Jog Dial to select Key Beep/Buzzer Use this menu to set the input voltage limit so an alarm will sound if the voltage goes below the cutoff value. The voltage alarm value can be set anywhere from 10.0 to 11.0V. To select a value other than the default parameter: • Press the Jog Dial so the voltage value flashes • Rotate the Jog Dial to select the voltage value • Press the Jog Dial to save the value • Rotate the Jog Dial to select External and Internal Temperatures By selecting the External and Internal Temperatures Screen you can view the current temperatures of both the battery (external) and the charger (internal). The optional temperature sensor (DYN5033) is required for external temperature measurement. g RESET FACTORY SETTINGS h VERSION • Press the Jog Dial to reset the charger to factory settings • Press the Jog Dial to select VERSION By selecting the Version Screen you can view the version (revision number) of the software on your charger. You may exit this menu at any time by pressing the Mode key to return to the main menus. ©2013 Horizon Hobby Inc. Dynamite, Passport, EC3 and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, Inc. iPhone and iPod are trademarks of Apple, Inc., registered in the U.S. and other countries. Microsoft®, Windows XP® and Windows Vista® are registered trademarks of the Microsoft Corporation. Created 10/12 Document sheet 1/4 32772.1