Download Chief QMP1TB rack accessory

INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Music Stand Table Top
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
QMP1T
QMP1T
Installation Instructions
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® and Centris® are registered trademarks of Milestone AV
Technologies. All rights reserved.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the QMP1T does not exceed 50 lbs
(22.7 kg). Use with products heavier than the maximum weight
indicated may result in collapse of the mount and its
accessories causing possible injury.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
DIMENSIONS
36.0
24.0
OUTER COLUMN
CLAMP DIM
22.6
INNER COLUMN
CLAMP DIM
PILOT HOLES FOR
OPTIONAL KEYBOARD TRAY
QMP1KH OR QMP1KB
6.845
4.0
DIMENSIONS: INCHES
2
Installation Instructions
QMP1T
LEGEND
Tighten Fastener
Phillips Screwdriver
Apretar elemento de fijación
Destornillador Phillips
Befestigungsteil festziehen
Kreuzschlitzschraubendreher
Apertar fixador
Chave de fendas Phillips
Serrare il fissaggio
Cacciavite a stella
Bevestiging vastdraaien
Kruiskopschroevendraaier
Serrez les fixations
Tournevis à pointe cruciforme
Loosen Fastener
Hex-Head Wrench
Aflojar elemento de fijación
Llave de cabeza hexagonal
Befestigungsteil lösen
Sechskantschlüssel
Desapertar fixador
Chave de cabeça sextavada
Allentare il fissaggio
Chiave esagonale
Bevestiging losdraaien
Zeskantsleutel
Desserrez les fixations
Clé à tête hexagonale
3
QMP1T
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
M3 (included)
#2
PARTS
A (2)
[Array clamp, outer]
B (2)
[Array clamp, inner]
D (1)
[Table brace]
F (1)
[Table top]
E (1)
[Attachment plate]
H (1)
10-24 x 1/2"
C (1)
[Table bracket]
J (6)
10-24 x 3/8"
K (4)
1/4-20 x 3/4"
L (6)
#10 x 5/8"
G (6)
[Cable tie, 5-1/2"]
M (4)
10-24
4
N (2)
#10
P (1)
M3
Installation Instructions
QMP1T
ASSEMBLY
4.
Fasten the table top (F) to the table bracket assembly using
six #10 x 5/8" Phillips wood screws (L). (See Figure 3)
The QMP1T is designed to be attached to the Chief QMP1FB
fixed music stand or the QMB1MB mobile music cart.
1.
Attach column to cart/stand base (not included) following
instructions included with cart/stand (not included).
2.
Attach table bracket (C) to attachment plate (E) using one
10-24 x 1/2" Phillips undercut machine screw (H), two 10-24
x 3/8" button head cap screws (J), two #10 flat washers (N),
and four 10-24 nylon lock nuts (M). (See Figure 1)
2
(F)
Table bracket
assembly
(J) x 2
(E)
2
4
(H) x 1
(L) x 6
Figure 3
(N) x 2
(C)
5.
(M) x 4
Fasten the table top assembly to the cart/stand using four
1/4-20 x 3/4" button head cap screws (K) through two array
clamps-inner (B) or two array clamps-outer (A). (See Figure
5)
Figure 1
3.
Fasten table brace (D) to bracket assembly using four 10-24
x 3/8" button head cap screws (J). (See Figure 2)
3
5
(K) x 4
(J) x 4
Table top
assembly
(A or B) x 2
[B shown]
(D)
Bracket assembly
Figure 2
(Back of column - QMP1FB/
QMP1MB)
Figure 4
5
QMP1T
Installation Instructions
Cable Management
NOTE: There are four cable tie holes in the table bracket.
Cable ties (G) may be added for cable management of
keyboard cables, mouse cables and other
miscellaneous cables. (See Figure 5)
Table top
Cable tie holes
(Front view - table top and bracket)
Figure 5
6
Installation Instructions
QMP1T
7
QMP1T
Installation Instructions
USA/International
Europe
Chief Manufacturing, a products division
of Milestone AV Technologies
8832-002049 Rev00
2011 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
1/11
Asia Pacific
A
P
F
A
P
F
A
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477