Download Chief TA300
Transcript
INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation Side Speaker Bracket Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description TA300 TA300 Installation Instructions DISCLAIMER CAUTION: A CAUTION alerts you to the possibility of Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. damage or destruction of equipment if you do not follow the corresponding instructions. WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided. WARNING: Failure to provide adequate structural strength Chief® is a registered trademark of Milestone AV Technologies. All rights reserved. for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. IMPORTANT WARNINGS AND CAUTIONS! WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all equipment and accessories mounted on the TA300 bracket does not exceed 20 lbs (9.08 kg) or 10 lbs (4.54 kg) per speaker. WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. DIMENSIONS 20.6 .813 41.3 1.625 938.3 36.942 MINIMUM EXTENSION 3.4 .13 DEPTH ADDED TO MOUNT 1502.8 59.165 17.2 .68 425.2 16.7 472.2 18.6 7.1 .280 410.1 16.15 485.4 19.1 10.2 .40 MAXIMUM EXTENSION 1570.9 61.8 2 68.1 2.68 20.6 .81 Installation Instructions TA300 LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestiging losdraaien Gat boren Desserrez les fixations Percez un trou Phillips Screwdriver Adjust Destornillador Phillips Ajustar Kreuzschlitzschraubendreher Einstellen Chave de fendas Phillips Ajustar Cacciavite a stella Regolare Kruiskopschroevendraaier Afstellen Tournevis à pointe cruciforme Ajuster Open-Ended Wrench Remove Llave de boca Quitar Gabelschlüssel Entfernen Chave de bocas Remover Chiave a punte aperte Rimuovere Steeksleutel Verwijderen Clé à fourche Retirez By Hand Optional A mano Opcional Von Hand Optional Com a mão Opcional A mano Opzionale Met de hand Optie À la main En option Hex-Head Wrench Security Wrench Llave de cabeza hexagonal Llave de seguridad Sechskantschlüssel Sicherheitsschlüssel Chave de cabeça sextavada Chave de segurança Chiave esagonale Chiave di sicurezza Zeskantsleutel Veiligheidssleutel Clé à tête hexagonale Clé de sécurité 3 TA300 Installation Instructions TOOLS REQUIRED FOR INSTALLATION #2 3/8" 5/32" (included) 1/8" (included) PARTS A (2) [horizontal bracket] C (2) [speaker bracket] B (2) [attachment bracket] E (8) F (4) D (8) #10-24 x 3/8" #10-24 x 1/4" #10-24 x 1/2" K (1) 5/32" 4 G (4) #10 L (1) 1/8" H (8) #10-24 J (8) #10-24 x 1/2" Installation Instructions TA300 Installation TS3XX or iCF30 Installation Install Attachment Brackets to Faceplate TS525 or iCF50 Installation IMPORTANT ! : If also installing center channel speaker bracket (TA350) or another accessory above or below display, install that bracket at this point instead of the respective attachment bracket (B). The attachment bracket will not be used in these cases as the accessory brackets will connect directly to the horizontal brackets (A). See corresponding installation instructions for details. NOTE: Display does NOT have to be removed to attach brackets to TS525TU or iCF50 faceplate. IMPORTANT ! : If also installing center channel speaker bracket (TA350) or another accessory above or below display, install that bracket at this point instead of the respective attachment bracket (B). The attachment bracket will not be used in these cases as the accessory brackets will connect directly to the horizontal brackets (A). See corresponding installation instructions for details. 1. 1. If already installed, remove display from faceplate. See swing arm installation instructions for details. 2. Use four #10-24 x 1/2" Phillips flat head cap screws (J) and four #10-24 lock nuts (H) to connect attachment bracket (B) to upper holes on faceplate. (See Figure 3) Use four #10-24 x 1/4" button head cap screws (E) to connect attachment bracket (B) to upper holes on swing arm faceplate. (See Figure 1) (H) x 4 (display not shown for clarity) 1 (B) 2 (E) x 4 (J) x 4 (B) Figure 3 3. Figure 1 2. Use four #10-24 x 1/2" Phillips flat head cap screws (J) and four #10-24 lock nuts (H) to connect second attachment bracket (B) to lower holes on faceplate. (See Figure 4) Use four #10-24 x 1/4" button head cap screws (E) to connect second attachment bracket (B) to lower holes on swing arm faceplate. (See Figure 2) (display not shown for clarity) (B) (H) x 4 (B) 2 3 (E) x 4 (J) x 4 Figure 4 Figure 2 3. Proceed to Speaker Bracket Installation Section. 4. Install display to faceplate. See swing arm installation instructions for details. 5 TA300 Installation Instructions Speaker Bracket Installation 1. Use four #10-24 x 3/8" Phillips machine screws (D) to connect one speaker bracket (C) to upper and lower horizontal brackets (A). (See Figure 5) 3 (F) x 2 (B) (G) x 2 (A) x 2 (C) Figure 7 1 (D) x 4 4. If necessary, extend arms beyond edge of display by loosening (not removing) extension adjustment screws on horizontal brackets and extending arms. Tighten adjustment screws when desired position is reached. (See Figure 8) 5. Use four #10-24 x 3/8" Phillips machine screws (D) to connect second speaker bracket (C) to upper and lower horizontal brackets (A). (See Figure 8) Figure 5 2. Slide connected horizontal brackets (A) and speaker bracket (C) onto back of display until center two holes on top horizontal bracket are aligned with two slots on top of attachment bracket (B). (See Figure 6) 5 (D) x 4 4 2 2 4 4 Figure 8 2 Figure 6 3. 6 Use two #10-24 x 1/2" button head cap screws (F) and two #10 washers (G) to connect top horizontal bracket (A) to attachment bracket (B). (See Figure 7) extension adjustment screw Installation Instructions 6. TA300 Use two #10-24 x 1/2" button head cap screws (F) and two #10 washers (G) to connect lower horizontal bracket (A) to either attachment bracket (B), TA350 bracket (if also using center channel) or other accessory bracket. See corresponding installation instructions for details if another bracket is being installed. (See Figure 9) Adjustments Extension Adjustment 1. Loosen four extension adjustment screws on horizontal brackets. (See Figure 11) 2. Adjust speaker brackets to desired horizontal positions. (See Figure 11) 3. Tighten four extension adjustment screws when desired mounting position is reached. (See Figure 11) (B) 1 3 2 (G) x 2 2 7 (F) x 2 Figure 9 7. Attach speakers to speaker brackets (C) appropriate hardware (not provided). Adjust extension of horizontal brackets as needed. (See Figure 10) Figure 11 WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all equipment and accessories mounted on the TA300 bracket does not exceed 20 lbs (9.08 kg) or 10 lbs (4.54 kg) per speaker. speakers (example) Figure 10 7 TA300 Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8805-002021 Rev01 2011 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 08/11 Asia Pacific A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands +31 (0)40 2668620 +31 (0)40 2668615 Office No. 1 on 12/F, Shatin Galleria 18-24 Shan Mei Street Fotan, Shatin, Hong Kong P 852 2145 4099 F 852 2145 4477