Download Chief QMP1TB rack accessory
Transcript
INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation Music Stand Table Top Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description QMP1T QMP1T Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. Chief® and Centris® are registered trademarks of Milestone AV Technologies. All rights reserved. WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided. WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. WARNING: Exceeding the weight capacity can result in IMPORTANT WARNINGS AND CAUTIONS! WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached to the QMP1T does not exceed 50 lbs (22.7 kg). Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury. CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions. DIMENSIONS 36.0 24.0 OUTER COLUMN CLAMP DIM 22.6 INNER COLUMN CLAMP DIM PILOT HOLES FOR OPTIONAL KEYBOARD TRAY QMP1KH OR QMP1KB 6.845 4.0 DIMENSIONS: INCHES 2 Installation Instructions QMP1T LEGEND Tighten Fastener Phillips Screwdriver Apretar elemento de fijación Destornillador Phillips Befestigungsteil festziehen Kreuzschlitzschraubendreher Apertar fixador Chave de fendas Phillips Serrare il fissaggio Cacciavite a stella Bevestiging vastdraaien Kruiskopschroevendraaier Serrez les fixations Tournevis à pointe cruciforme Loosen Fastener Hex-Head Wrench Aflojar elemento de fijación Llave de cabeza hexagonal Befestigungsteil lösen Sechskantschlüssel Desapertar fixador Chave de cabeça sextavada Allentare il fissaggio Chiave esagonale Bevestiging losdraaien Zeskantsleutel Desserrez les fixations Clé à tête hexagonale 3 QMP1T Installation Instructions TOOLS REQUIRED FOR INSTALLATION M3 (included) #2 PARTS A (2) [Array clamp, outer] B (2) [Array clamp, inner] D (1) [Table brace] F (1) [Table top] E (1) [Attachment plate] H (1) 10-24 x 1/2" C (1) [Table bracket] J (6) 10-24 x 3/8" K (4) 1/4-20 x 3/4" L (6) #10 x 5/8" G (6) [Cable tie, 5-1/2"] M (4) 10-24 4 N (2) #10 P (1) M3 Installation Instructions QMP1T ASSEMBLY 4. Fasten the table top (F) to the table bracket assembly using six #10 x 5/8" Phillips wood screws (L). (See Figure 3) The QMP1T is designed to be attached to the Chief QMP1FB fixed music stand or the QMB1MB mobile music cart. 1. Attach column to cart/stand base (not included) following instructions included with cart/stand (not included). 2. Attach table bracket (C) to attachment plate (E) using one 10-24 x 1/2" Phillips undercut machine screw (H), two 10-24 x 3/8" button head cap screws (J), two #10 flat washers (N), and four 10-24 nylon lock nuts (M). (See Figure 1) 2 (F) Table bracket assembly (J) x 2 (E) 2 4 (H) x 1 (L) x 6 Figure 3 (N) x 2 (C) 5. (M) x 4 Fasten the table top assembly to the cart/stand using four 1/4-20 x 3/4" button head cap screws (K) through two array clamps-inner (B) or two array clamps-outer (A). (See Figure 5) Figure 1 3. Fasten table brace (D) to bracket assembly using four 10-24 x 3/8" button head cap screws (J). (See Figure 2) 3 5 (K) x 4 (J) x 4 Table top assembly (A or B) x 2 [B shown] (D) Bracket assembly Figure 2 (Back of column - QMP1FB/ QMP1MB) Figure 4 5 QMP1T Installation Instructions Cable Management NOTE: There are four cable tie holes in the table bracket. Cable ties (G) may be added for cable management of keyboard cables, mouse cables and other miscellaneous cables. (See Figure 5) Table top Cable tie holes (Front view - table top and bracket) Figure 5 6 Installation Instructions QMP1T 7 QMP1T Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8832-002049 Rev00 2011 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 1/11 Asia Pacific A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands +31 (0)40 2668620 +31 (0)40 2668615 Office No. 1 on 12/F, Shatin Galleria 18-24 Shan Mei Street Fotan, Shatin, Hong Kong P 852 2145 4099 F 852 2145 4477