Download Craftsman 917.377520 Owner`s manual
Transcript
Owner's Manual ® 5.0 HORSEPOWER 22" REAR DISCHARGE POWER PROPELLED ROTARY LAWN MOWER Model No. 917.377520 o o Safety Assembly Operation Maintenance , Espafioi o Repair Parts CAUTION: Read and follow all Safety Rules and Instructions before operating this equipment Sears, Roebuck and Co., Hoffman Estates, IL 60t79 Warranty Safety Rules Assembly Operation Maintenance Schedule Maintenance 2 2 4 6 10 10 Product Specifications Sewice and Adjustments Storage Troubleshooting Repair Parts Parts Ordering 11 14 15 16 35 Back Cover LIMITED TWO YEAR WARRANTY ON CRAFTSMAN POWER MOWER For two years from date of purchase, when this Craftsman Lawn Mower is maintained, lubricated, and tuned up according to the operating and maintenance instructions in the owner's manual, Sears will repair free of charge any defect in material or workmanship. If this Craftsman Lawn Mower is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase. This Warranty does not cover: o Expendable items which become worn during normal use, such as rotary mower blades, blade adapters, belts, air cleaners and spark plug. o Repairs necessary because of operator abuse or negligence, including bent crankshafts and the failure to maintain the equipment according to the instructions contained in the owner's manual° Warranty service is available by returning the Craftsman power mower to the nearest Sears Service Center/Department in the United States. This warranty applies only while this product is in use in the United States. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. SEARS, ROEBUCK AND CO., D/817 WA, HOFFMAN, ESTATES, ILLINOIS 60179 TRAINING: o Read this operator's manual carefully_ Become familiai" with the controls and know how to operate your mower properly. Learn how to quickly stop mower. o Do not allow children to use your mower. Never allow adults to use mower without proper instructions. • Keep the area of operation clear of all persons, especially small children and pets_ • Use mower only as the manufacturer intended and as described in this manual. • Do not operate mower if it has been dropped or damaged in any manner_ Always have damage repaired before using your mower. ° Do not use accessory attachments that are not recommended by the manufac- turer. Use of such attachments may be hazardous. The blade turns when the engine is running. PREPARATION: o Always thoroughly check the area to be mowed and clear it of all stones, sticks, wires, bones, and other foreign objects. These objects will be thrown by the blade and can cause severe injury. ° Alway s wear safety glasses or eye shields when starting and while using your mower. ,, Dress properly. Do not operate mower when barefoot or wearing open sandals. Wear only solid shoes with good traction when mowing. o Check fuel tank before starting engine. Do not fill gas tank indoors, when the engine is running or when the engine is 2 hot. Allow the engine to cool for several minutes before filling the gas tank. Clean off any spilled gasoline before starting the engine. Always make wheel height adjustments before starting your mower. Never attempt to do this while the engine is running. Mow only in daylight or good artificial light. o Never cut grass by pulling the mower towards you. Mow across the face of slopes, never up and down or you might lose your footing. Do not mow excessively steep slopes. Use caution when operating the mower on uneven terrain or when changing directions -- maintain good footing. ° Never operate your mower without proper guards, plates, grass catcher or other safety devices in place. OPERATION" ° Keep your eyes and mind on your mower and the area being cut. Do not let other interests distract you. ° Do not mow wet or slippery grass. Never run while operating your mower. Always be sure of your footing -- keep a firm hold on the handles and walk. , Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times. ° Always stop the engine whenever you leave or are not using your mower, or before crossing driveways, walks, roads, and any gravel---covered areas. o Never direct discharge of material toward bystanders nor allow anyone near the mower while you are operating it. ° Before cleaning, inspecting, or repairing your mower, stop the engine and make absolutely sure the blade and all moving parts have stopped. Then disconnect the spark plug wire and keep it away fi'0m the spark plug to prevent accidental starting° o Do not continue to run your mower if you hit a foreign object. Follow the procedure outlined above, then repair any damage before restarting and operating you mower. • Do not change the governor settings or overspeed the engine. Engine damage or personal injury may result. • Do not operate your mower if it vibrates abnormally. Excessive vibration is an indication of damage; stop the engine, safely check for the cause of vibration and repair as required. o Do not run the engine indoors. Exhaust fumes are dangerous° MAINTENANCE AND STORAGE; ° Check the blade and the engine mounting bolts often to be sure they are tightened properly. ° Check all bolts, nuts and screws at frequent intervals for proper tightness to be sure mower is in safe working condition. - Keep all safety devices in place and working. o To reduce fire hazard, keep the engine free of grass, leaves or excessive grease and oilo ° Check grass catcher often for deterioration and wear and replace worn bags. Use only replacement bags that are recommended by and comply with specifications of the manufacturer of your mower. , Always keep a sharp blade on your mower. ° Allow engine to cool before storing in any enclosure. ° Never store mower with fuel in the tank inside a building where fumes may reach an open flame or an ignition source such as a hot water heater, space heater, clothes dryer, etc. CAUTION: Always disconnect spark plug wire and place wire where it cannot contact spark plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs. WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. 3 Theseaccessories wereavailablewhenthislawn mower was produced. They are also available at most Sears retail outlets and service centers. Most Sears stores can also order repair parts for you, when you provide the model number of your lawn mower. Some of these accessories may not apply to your lawn mower. LAWN MOWER PERFORMANCE J,,, CLIPPING DEFLECTOR FOR REAR DISCHARGE LAWN MOWERS MULCHER KITS GRASS CATCHERS FOR REAR DISCHARGE LAWN MOWERS STABILIZER GRASS CATCHERS FOR SIDE DISCHARGE LAWN MOWERS GAS CANS LAWN MOWER MAINTENANCE MUFFLERS AIR FILTERS . BELTS BLADES BLADE ADAPTERS Read these instructionsand this manual in its entirety before you attempt to assemble or operate your new lawn mower. "four new lawn mower has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc. necessary to complete the assembly have been placed in the parts bag. To ensure safe and proper operation of your lawn mower, all parts and hardware you assemble must be tightened securely, Use the correct tools as necessary to ensure proper tightness. O ,:, WHEELS ENGINE OIL IMPORTANT: Unfoldhandles carefully so as notto pinch ordamage controlcables. o Raise handlesuntillower handle section locks intoplace in mowing position. • Remove protectivepadding, raise upper handle section intoplace on lower handle and tightenboth handle knobs. o Remo,,iehandle paddingholding operator presence control bar to upper handle. o Your lawn mower handle can be adjusted for your mowing comfort. Refer to "Adjust Handle" in the Service and Adjustment section of this manual. Remove looseparts includedwith mower. Cut down two end comers of carton and lay end panel down flaL Remove all packing materials except padding between upper and lower handle and padding holding operator presence control bar to upper handle. , SPARK PLUGS _, ,,,, ° Roll lawn mower out of carton and check carton thoroughly for additional loose parts. HOW TO SET UP YOUR LAWN MOWER TO UNFOLD HANDLE TO REMOVE LAWN MOWER FROM CARTON Q _ 4 NOTE: For shippingpurposes,the rear wheelson your lawn mowerare not adjustedto the same positionas the front wheels. Beforeoperatingmoweradjust allwheels to the same cuttingheight position. Operator presence control bar Uppper handle_./,_ Lift up /_,,_ "J'S"Lift up// /.,_ frame until both ends of frame are exposed out of the front opening. o Assemble lower frame to tubular frame as shown. Be sure handle is outside of bag and frames are fully seated as shown in inset_ ° Slip vinyl bindings over frame. NOTE: If vinyl bindings are too stiff, hold them in warm water for a few minutes° If bag gets wet, let it dry before using. Sewn hem Tubular frame /Y M°wing / ! position Lower handle TO INSTALL ATTACHMENTS Your lawn mower was shipped ready to be used as a mulcher. To convert to bagging or discharging: o Open rear door and remove mulcher plug. Store mulcher plug in a safe place. o You can now install catcher or optional clipping deflector. , To return to mulching operation, install mulcher plug into discharge opening of mower. Be sure all tabs are seated properly. Flip lid Sewn hem Lower Trame 7/ Tubular frame (Frames must be fully seated) Lower frame handle Mulcher plug _ CAUTION: Do not run your lawn mower without mulcher plug in place or approved clipping deflector or grass catcher in place. Never attempt to operate the lawn mower with the rear door removed or \ Vinyl bindings propped open. TOASSEMBLE GRASS CATCHER o Insert leg of tubularframe through front opening of grass catcher and thread frame into sewn hem of bag. NOTE: Keep bag hem gathered on the straight leg of the tubular frame. ° When frame comes out the other end of sewn hem, immediately work the end of frame down inside the bag as shown in inset° = Slide sewn hem evenly around the tubular 5 i I KNOW YOUR READ THIS LAWN MOWER OWNER'S MANUALAND SAFETY RULES BEFORE OPERATING YOUR LAVMNMOWER. Compare the illustrations with your lawn mower to familiarize yourself with the location of various controls and adjustments, Save this manual for future ref..erence_.............................................................................................. .............................................................................................. These symbols may appear on your lawn mower or in literature Learn and understand their meaning. supplied with the product, & 4 o.e CAUTION ENGINE ENGINE FAST SLOW CHOKE FUEL OIL OR WARNIN&__ .ON .......... OFF DANGER, KEEP HANDS AND FEET AWAY Engine zone control cable -Operator presence control bar Drive control lever Srarter handle Handle knob Grass catcher Mulcher plug Engine oil cap w/dipstick Housing Drive cover Gasoline cap Wheel adjuster (on each wheel) Sears rotary walk-behind power lawn mowers conform to the safety standards of the American National Standards Institute and the U,S. Consumer Product Safety Commission, The blade tums when the engine is nmning. Starterhandie-usedfor starting the engine. " Operator pm,senee control bar - must be Drive control lever used to engage powerheld down to the handle to start the engine. propelled forward motion of lawn mower. Release to stop the engine. Mulcher plug must be removed to convert to Primer- pumps additional fuel from the bagging or discharging operation, carburetor to the cylinder for use when starting a cold engine, _L .......... : ==..: .................. The operationof any lawn mowercan resultin foreignobjectsthrown intothe eyes,which can resultin severeeye damage°Alwayswearsafetyglassesor eye shieldswhileoperatingyour lawn moweror performingany adjustmentsor repairs. We recommenda wide vision safety maskoverthe spectaclesor standardsafetyglasses. HOW TO USE YOUR LAWN MOWER CAb'I'ION: Do not nJn your lawn mower without mulcher plate in place and door closed or without an approved clipping deflector or grasscatcher in place. Never attempt to operate the lawn mower w_ the rear door removed or propped open. ENGINE SPEED The engine speed was set at the factory for optimum performance. Speed is not adjustable_ ENGINE ZONE CONTROL Plate Tab Lower Wheels for High Cut Lever Raise Wheels for Low Cut TO ATTACH GRASS CATCHER Close the flip Iido Fliplid must be closed whileoperating lawn mower, Lift the rear door on the mower housing and place the grass catcher frame onto the formed tabs on the rear door hinge bracket. The grass catcher is secured to the lawn mower housing when the rear door is lowered onto the grass catcher frame. o CAUTION: Do not run your la:wnmower without clipping deflector or approved grass catcher in place. Never attempt to operate the lawn mower with the rear door removed or propped open. CAUTION: Federal regulations require an engine control to be installed on this lawn mower in order to minimize the risk Hinge bracket of blade contact injury. Do not under any circumstances attempt to defeat the function of the operator control° The blade turns when the engine is nJnningo = Your lawn mower is equipped with an operator presence control bar which requires the operator to be positional behind the lawn mower handle to start and operate the lawn mower_ TO ADJUST CUTTING HEIGHT ° Raise wheels for low cut and lower wheels for high cut. o Adjust cutting height to suit your requirements. Medium position is best for most lawns. o To change cutting height, squeeze adjuster lever toward wheel. Move wheel up or down to suit your requirements. Be sure all wheels are in the same setting. Rear door Formed tabs TO EMPTY GRASS CATCHER ° To remove grass catcher, release operator presence control bar to stop engine° ° Lift up rear door and remove the grass catcher by the handle. o Do not drag the bag when emptying; it witl cause unnecessary wear° NOTE: Adjuster is properly positioned when plate tab inserts into hole in lever. Also, 9_position adjusters (if so equipped) allow lever to be positioned between the plate tabs. 7 DRIVE CONTROL o Self-propelling is controlled by holding the operator presence control bar down to the handle and pushing the drive control [ever forward until it clicks; then release the lever. • Forward motion will stop when the operator presence control bar is released° To stop forward motion without stopping engine, release the operator presence control bar slightly until the drive control disengages. Hold operator presence control bar down to handle to continue mowing without selfpropelling. o To keep drive control engaged when turning comers, push down on handle and lift front wheels off ground while turning lawn mower. Operator presence control bar Drive To engage drive control Drive control desengaged :!'.} ADD GASOLINE • Fill fuel tank. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness. IMPORTANT: When operating in temperatures below 32°F(0°C), use fresh, clean winter grade gasoline to help insure good cold weather starting° WARNING: Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it nJnuntil the fuel lines and carburetor are empty. Use fresh fue! next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage_r_ay occur. CAUTION: Fill to bottom of gas tank filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame. BEFORE STARTING ENGINE OIL Your lawn mower is shipped without oil in the engine. - Be sure mower is level and area around oil fill is clean. o Remove engine bil cap w!dipstick and fill tO the full line on the dipstick. o Use 20 ozs. of oil. For type and grade of oil to use, see"ENGINE" in Customer Responsibilities section of this manual. • Pour oil slowly. Do not over fill. o Check oi! level before each use, Add oil if needed. Fill to ful! line on dipstick. ° To read proper level, tighten engine oil cap each time. o Reinstall engine oil cap and tighten. ° Change the oil after every 25 hours of operation or each season. You may need to change the oil more often under dusty, dirty conditions. ,=filler cap Entine oil cap w/ dipstick TO START ENGINE ° To start a cold engine, push primer three (3) times before trying to start. Use a firm push. This step isnot usually necessary when starting an engine which has already run for_afew mim,_es. o Hold operator presence control bar down to the handle and pull starter handle quickly. Do not allow starter rope to snap back. o To stop engine, release operator presence control bar° NOTE: In cooler weather it may be necessary to repeat priming steps. In 8 warmer weather over priming may cause flooding and engine will not start, If you do flood engine, ,waita few minutes before attempting to start and do not repeat priming steps. lVlOWING TIPS o Under certain conditions, such as very tall grass, it may be necessary to raise the height of cut to reduce pushing effo_ and to keep from overloading the engine and leaving clumps of grass clippings. o For extremely heavy cutting, reduce the width of cut and raise the rear of the lawn mower housing one (t) wheel adjuster setting higher than the front for better discharge of grass. ° For better grass bagging and most cutting conditions, the engine speed should be set in the fast position. ° When using a rear discharge lawn mower in moist, heavy grass, clumps of cut grass may not enter the grass catcher. Reduce ground speed (pushing speed) and/or run the lawn mower over the area a second time_ , If a trail of grass clippings is left on the dght side of a rear discharge lawn mower, mow in a clockwise direction with a small overlap to collect the clippings on the next pass. o Keep top of engine around starter clear and clean of grass clippings and chaff. This will help engine air flow and extend engine life. - Pores in cloth grass catchers can become filled 'with dirt and dust with use and catchers will collect less grass. To prevent this, regularly hose catchers off with water and let dry before using. Max 1/3 MULCHING MOWING TIPS IMPORTANT: For best performance, keep mower housing free of built-up grass and trash. See "Cleaning" in CUSTOMER RESPONSIBILITIES section of this manual. , The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will provide the best recutting action of the blades. o Avoid cutting your lawn when it is weL Wet grass tends to form clumps and interferes with the mulching action. "]'he best time to mow your lawn is the early aftemoon: At this time the grass has dried and the newly cut area will not be exposed to the direct sun. o For best results, adjust the lawn mower cuttJng height so that the lawn mower cuts off only the top one-third of the grass blades. tf the lawn is overgrown it will be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of mulched grass° For extremely heavy mulching, reduce your width of cut by overlapping previously cut path and mow slowly. • Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a second cut, mow across or perpendicular to the first cut path. ° Change your cutting pattern from week to week. Mow north to south one week then change to east to west the next week. This will help prevent matting and graining of the lawn. CleaPJlnspect Grass Catcher (If Equipped) ' M Clean Lawn Mower 6/ ....... (Power-Propelled Clean Under DriveMowers) Cover Check drive belt/pulleys" E (Power-Propelled Mowers) a CheckJSharpeniRePlace Blade O 6/ 6/ 6/ 6/ ,, , ,,,i 6/ ..... :_, 6/ E Check Engine Ofi Level N Change Engine Otl G clean Atr Filter I inspect Muffler N Clean or Replace Spark Plug 6/ 6/ Lubrication Chart Clean Ba_erytRecharge (Electric Start Mowers) 6/ 6/ E Replace Air Filter Paper Cartridge 6/2 !{ - Change more often when operating under a heavy load or in high ambient temperatures_ 2 * Service more often when operating in dirty or dusty conditions 3 _ Replace blades more oftsn when mewing tn sandy sell, 4 - Charge 48 hours at end of season_ GENERAL RECOMMENDATIONS The warranty on this !awn mower does not cover items that have been subjected to operator abuse or negligence, To receive full value from the warranty, operator must maintain mower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your unit. All adjustments in the Service and Adjustments section of this manual should be checked at least once each season° = Once a year, replace the spark plug, replace air filter element and check blade for wear. A new spark plug and clean/new air filter element assures proper air-fuel mixture and helps your engine run better and last longer. o Follow the maintenance schedule in this manual. BEFORE EACH USE - Check engine oil level. o Check for loose fasteners. LUBRICATION Keep unit welt lubricated (See "LUBRICATION CHART"). LUBRICATION Wheel adjuster CHART i @ Er oil (_ Handle mounting pin (_ Rear door hinge O spra ,l.b, t Refer to CUSTOMER RESPONSIBILITIES "ENGINE" section. IMPORTANT: Do not oil or grease plastic wheel bearings. Viscous lubricants will attract dust and dirt that will shorten the life of the self lubricating bearings° If you feel they must be lubricated, use only a dry, powdered graphite type lubricant sparingly. 1() PRODUCT SPECiFiCATiONS MODEL NUMBER 917.377520 SERIAL NUMBER DATE OF PURCHASE HORSEPOWER: 5.0 DISPLACEMENT: 11.5 CU. IN. GASOLINE CAPACITY! TYPE: 1.6 QUARTS z* UNLEADED REGULAR OIL TYPE (API-SF/SG/SH): SAE 30 (ABOVE 32°F) SAE 5W-30 (BELOW 32°F) OIL CAPACITY: SPARK PLUG(GAP: 20 OZSo .030") CHAMPION RJ19LM OR J19LM VALVECLEARANCE: INTAKE: .005" EXHAUST: .007" SOLID STATE IGNITION AIR GAP: .010 IN. BLADE BOLT TORQUE: 35-40 FT. LBS. The model and serial numbers will be found on a decal attached to the rear of the lawn mower housingoRecord both serial number and date of purchas e in space provided above. LAWN MOWER Always observe safety rules when performing any maintenance. TIRES • Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. o Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. BLADE CARE For best results, mower blade must be kept sharp. Replace bent or damaged blades. TO REMOVE BLADE ° Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with spark plugo o Turn lawn mower on its side. Make sure air filter and carburetor are up. ° Use a wood block between blade and mower housing to prevent blade from turning when removing blade boll ° Protect your hands,Mth gloves and/orwrap blade with heavy cloth. o Remove blade bolt by turning counterclockwise. Use a 9/16" box or open-end wrench. o Remove blade and attaching hardware (bolt, lock washer and hardened washer). NOTE: Remove the blade adapter and check the key inside hub of blade adapter. The key must be in good condition to work properly. Replace adapter if damaged. TO REPLACE BLADE o Position the blade adapter on the engine crankshaft. Be sure key in adapter and crankshaft keyway are aligned° ° Position blade on the blade adapter aligning the two (2) holes in the blade with the raised lugs on the adapter. o Be sure the trailing edge of blade (opposite sharp edge) is up toward the engine. o Install the blade bolt with the lock washer and hardened washer into blade adapter and crankshaft. ° Use block of wood between blade and lawn mower housing and tighten the blade bolt, turning clockwise. ° The recommended tightening torque is 3540 ft. lbs, IMPORTANT: Blade bolt is grade 8 heat treated. 11 NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced. TO SHARPEN BLADE Care should be taken to keep the blade balanced° An unbalanced blade will cause eventual damage to lawn mower or engine. • The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower° o To check blade balance, drive a nail into a beam or wail. Leave about one inch of the straight nail exposed. Place center hole of blade over the head of the nail. if blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced. Blade Crank shaft ada_ keyway o Remove any trash or grass cuttings from inside the dust cover, pinion and/or drive wheel gear teeth. ° Put wheels back in place. • if after cleaning, the drive wheels do not turn freely, contact your nearest authorized service center. GEAR CASE ° To keep your drive system working properly, the gear case and area around the drive should be kept clean and free of trash build-up. Clean under the drive cover twice a season. - The gear case is filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case. . If lubricant is required, use only Texaco Starplex Premium 1 Grease, Part No. 750355. De not substitute. ENGINE LUBRICATION Use only high quality detergent oil rated with API service classification SF, SG, or SH. Select the oil's SAE viscosity grade according to your expected operating temperature. Blade SAE VISCOSITY GRADES bolt Lock washer ......... Crank shaft Hardened washer edge Blade adapter GRASS CATCHER . The grass catcher may be hosed with water, but must be dry when used° o Check your grass catcher often for damage or deterioration. Through normal use itwill wear. if catcher needs replacing, replace only with a manufacturer approved replacement catcher. Give the lawn mower model number when ordering. DRIVE WHEELS Check front drive wheels each time before you mow to be sure they move freely. The wheels not turning freely means trash, grass cuttings, etc, are in the drive wheel area and must be cleaned to free drive wheels. if necessary to clean the drive wheels, check both front wheels. ° Remove hubcaps, hairpin cotters and washers. ° Remove wheels from wheel adjusters. _""/'ii _'C ..,.'m -_" _1o" o, TEM'PI_RATURE RANGE _T)C1PATEO ii _J __ !C=' :_o* _ 40" BEFORE N_ OIL CHANGE NOTE: Although m:uifi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils wiU result in increased oil consumption When used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil. Change after the first 25 hours of operation at least once a year ifthe lawn mower is not used for 25 hours in one year. Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil plug securely each time you check the oil level. TO CHANGE ENGINE OIL NOTE: Before tipping lawn mower to drain oil, drain fuel tank by running engine until fuel tank is empty. o Disconnectspark plugwirefrom spark plug and placewire whereit cannotcome in 12 contactwithsparkplug. o Removeengineoilcap;layasideon aclean surface. • Tiplawnmoweronitssideasshownand drainoilintoa suitablecontainer.Rocklawn mowerbackandforthto removeanyoil trappedinsideofengine. o Wipeoffanyspilledoilon lawnmowerand on sideof engine. • Fill engine with oil. Fill only to the "FULL" line on the dipstick. DO NOT overfi[l_ o Replace engine oil cap. o Reconnect spark plug wire to spark plug. Container AIR FILTER Your engine will not run properly and may be damaged by using a dirty air filter, Replace the air filter every year, more often if you mow in very dusty, dirty conditions. Do not wash air filter. TO CHANGE AIR FILTER - Loosen screw and tilt cover to remove. ° Carefully remove cartridge, ° Clean by gently tapping on a flat surface. If very dirty, replace cartridge° CAUTION: Petroleum solvents, sT_chas kerosene, are not to be used to clean cartridge. They may cause deterioration of the cartridge. Do not oil cartridge. Do not use pressurized air to clean or dry cartridge. MUFFLER inspect and replace corroded muffler as it could create a fire hazard and/or damage. SPARK PLUG Change your spark plug each year to make your engine start easier and run better. Set spark plug gap at .030 inch. CLEANING IMPORTANT: For best performance, keep mower housing free of built-up grass and trash. Clean the underside of your mower after each use° CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with the spark plug. ° Turn lawn mower on its side. Make sure air filter and carburetor are up. Clean the underside of your lawn mower by scraping to remove build-up of grass and trash. ° Clean engine often to keep trash from accumulating. A clogged engine runs hotter and shortens engine life. ° Keep finished surfaces aqd wheels free of all gasoline, oil,etc. o We do not recommend using a garden hose to clean lawn mower unless the electrical system, muffler, air filter and carburetor are covered to keep water out. Water in engine can result in shortened engine life. CLEAN UNDER DRIVE COVER Clean under drive cover at least twice a season, Scrape underside of cover with putty knife or similar tool to remove any build-up of trash or grass on underside of drive cover, Back e Cover .._ tabs Slots Cartridge Cover 13 CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: o Releasecontrolbar. o Make surethe bladeand all moving parts havecompletelystopped° o Disconnectspark plugwire fromspark plug andplace whereit cannotcome in contactwith plug. LAWN MOWER TO ADJUST CUTTING HEIGHT See 'q'O ADJUST CUTTING HEIGHT" in the Operation section of this manual. REAR DEFLECTOR The rear deflector, attached between the rear wheels of your lawn mower, is provided to minimize the possibility that objects will be thrown out the rear of the lawn mower into the operator's mowing position. If the rear deflector becomes damaged, it should be replaced. TO REMOVF_JREPLACE DRIVE BELT o Remove drive cover. Remove belt by pushing down on gear case pulley and roll belt off. o Turn lawn mower on its side with carburetor o Remove the starter rope guide from the lower handle. o Remove hairpin cotters. ° Disconnect the lower handle from the handle brackets. ° Tum the handle over and reassemble the hairpin cotters that have been removed, o Reassemble the starter rope guide_ ° Reassemble the controls and the operator presence control bar to the upper handle. CAUTION: The operator presence control bar must pivot freely to permit blade brake engagement when control bar is released. Do not over tighten the fasteners holding the controls to the upper handle. o To change from medium low to high position only the upper handle section wil! have to be turned over. ° To change from medium low to low position, only the lower handle section 'wilthave to be turned over. Shipping position Medium low high and fuel cap up. ° Remove blade, o Remove debris shield. o Remove belt from engine pulley on crankshaft. o install new belt by reversing above steps. o Always use factory approved belt to assure fit and long life, Drive cover rl i High Belt _3. L°W Push down TO ADJUST HANDLE Your lawn mower handle can be raised or lowered for your mowing comfort. Four (4) positions are available: high, medium high, medium low and low. Handles are shipped mounted in the medium low position. ° To change from medium low to medium high position, the upper and lower handle sections will have to be tumed over. ° Remove cable clips. o Remove the controls and operator presence control bar from the upper handle. _- \ , Lowerhandle Squeeze_"_'_to ""-__ bracket 14 Immediately prepare your lawn mower for storage at the end of the season or if the unit will not be used for 30 days or more. LAWN MOWER When lawn mower is to be stored for a period of time, clean itthoroughly, remove alldirt, grease, leaves, etc. Store in a dean, dry area. - Clean entire lawn mower (See "CLEANING" in the Customer Responsibilities section of this manual). o Lubricate as shown in the Customer Responsibilities section of this manual. o Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary. ° Touch up all rusted or chipped paint surfaces; sand lightly before painting. HANDLE "Youcan fold your lawn mower handle for storage. ° Squeeze the bottom ends of the lower handle toward each other until the lower handle clears the handle bracket, then move handle forward. • Loosen upper handle mounting bolts enough to allow upper handle to be folded back. IMPORTANT: When folding the handle4or storage or transportation, be sure to fold the handle as shown or you amy damage the control cables. o When setting up your handle from the storage position, the lower handle will automatically lock into the mowing position. Lower handle Handle bracket Squeeze to fold Operator presence control bar . Fold foward for storage__ __v, _" Upper / handle ,_//,_"_"_,) _';"Ji/_ iz/Fold ! backward Lower _ Mowing handle position ENGINE FUEL SYSTEM IMPORTANT: itis importantto prevent gum deposits from forming in essentialfuel system partssuch as carburetor, fuel system parts such as carburetor, fuel filter, fuel hose ortank during storage.,_Jso, experienceindicates that alcoholblended fuels ( calledgasoholorusing ethanolor methanol) can att_ct moisture whichleads to separation add formation of acids duringstorage_Acidic gas can damage the fuel systemof an engine while in storage. ° Drainthe fuel tank° o Startthe engine and let it run untilthe fuel linesand carburetor are empty. = Never use engine orcarburetor cleaner productsin the fuel tank or permanent damage may occur. . Use fresh fuel next season. NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage, Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer. Hairpin cotter 15 ENGINEOIL Drainoil(withenginewarm)andreplacewith cleanengineoil. (See"ENGINE"inthe CustomerResponsibilities sectionofthis manual). CYLINDER • Removesparkplug. o Pouroneounce(29ml)of oilthroughspark plugholeintocylinder. o Pullstarterhandleslowlya fewtimesto distributeoil. , Replace with new spark plug. OTHER o Do not store gasoline from one season to another. o Replace your gasoline can if your can starts TROUBLESHOOTING PROBLEM Does not start to rust. Rust and/or dirt in your gasoline will cause problems. o If possible, store your unit indoors and cover it to give protection from dust and dirL = Cover your unit with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which al!ows condensation to form and will cause your unit to rust. IMPORTANT: Never cover mower while engine and exhaust areas are still warm. CAUTION: Never store the lawn mower with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to coo! before storing in any enclosure. CHART . CAUSE ° Dirty air filter. o Out of fuel. ° Stale fuel. . ° ° ° o Water in fuelo ° ° Spark plug wire is disconnected_ , Bad spark plug. ° Loose blade or broken blade adapter. ° Control bar in released position. ° Control bar defective. ° 16 CORRECTION Clean/replaceair fitter_ Fill fuel tank° Drain tank and refill with fresh clean fuel. Drain fueltank and carburetor and refilltank with fresh gasoline° Connect wire to plug. ° Replace spark plug. ° Tighten blade bolt or replace blade adapter° ° Depress control bar to handle. ° Replace control ban 1 TROUBLESHOOTING CHART PROBLEM CAUSE CORRECTION Loss of power = Rear of lawn mower housing or cutting blade dragging in heavy grass. Cutting too much grass_ ° Set to "Higher Cu't" position. o Dirty air _tero ° Buildup of grass, leaves, and trashi_)hdermower. o Too much oil in engine. • Walking speed too fast. ° ° ° ° Set to "Higher Cut" position. Clean/replace air filter. Clean underside of mower housing. Check oil level. Cut at slower ,walking speed. Poor cut- uneven Excessive vibration • Worn, bent or loose blade. o Wheel heights uneven. Replace blade. Tighten blade bolt. Set all wheels at same = Buildup of grass, leaves and trash under mower. height Clean underside of mower housing. o Worn, bent or loose blade. o Bent engine crankshaft. Starter rope hard to pull o Engine flywheel brake is on when control bar is released. ° Bent engine crankshaft. ° Blade adapter broken. • Blade dragging in grass. Grass'catcher not filling (if so equipped) Hard to push ............. • Cutting height too low. o Lift on blade worn off. ,, Catcher not venting air. ° Grass is too high or wheel height is too Iow_ - Rear of lawn mower housing or blade dragging in grass. ° Grass catcher too full. ° Handle height position not right for you. 17 ......... ......... ° Replace blade. Tighten blade bolt. '+. , Contact an authorized service center. • Depress control bar to upper handle before pulling starter rope. o Contact an authorized service center. ° Replace blade adapter. ° Move lawn mower to cut grass or to hard surface to start engine. - Raise cutting heighL ° Replace blade. ° Clean grass catcher. • Raise cutting height. ° Raise rear of lawn mower housing one (1) se_ng higher° ° Empty grass catcher. • Adjust handle height to suit. Garantfa Reglas de Seguridad Montaje Operaci6n Mantenimiento Programa de Mantenimiento 18 18 20 22 26 26 Especificaciones del Producto Servicio yAdjustes Almacenamiento Identificaci6n de probtemas Partes de repuesto Orden de Partes GARANTfA LIMITADA DE DOS At£',IOSPARA LA SEGADORAA 27 30 21 33 Vea el manual ingles del duefio Contratapa MOTOR CRAFTSMAN Por dos (2) afios, a parfir de la fecha de compra, cuando esta Segadora Craftsman se mantenga, lubrique y aline segSn las instrucciones para la operad6n y el mantenimiento en el manual del duefio, Sears reparar_ gratis todo defecto en el material y la mano de obr& Si la Segadora Craftsman se usa para fines comerciales o de aniendo, esta garantia s(51ose aptica por noventa (90) dfas a partir de la fecha de compra. Esta Garantia no cubre: o Articulos que se desgastan durante el uso normal tales como las cuchillas segadoras rotatorias, los adaptadores de la cuchilla, las correas, los filtros de alre y las bujias. o Reparaciones necesarias debido al abuso o a la negligencia del operador, incluy_ndose a los cigi}efiales doblados y a la falta de mantenimiento del equiposegtin las instrucciones que se incluyen en el manual del due5o. EL SERVtCIO DE GARANTfA ESTA DISPONIBLE al devolver la segadpra a motor Craftsman al centro/ departmento de se_cio Sears mas cercano en los Estados UnfdosoEsta garantfa se aplica solamente mientras el producto este en uso en los Estados Unidos. Esta Garantfa le otorga derech(_s legales especfficos, y puede que tambi_n tenga otros derechos que yah'an de estado a estado. Sears, Roebuck and Co., D/817WA, Hoffman Estates, IL 60179 USA Los estandraresde seguridad exigen la presencia del operator en los c0ntroles para reducir a un rninimo et riesgo de lesionarse. Su unidad viene equipada con dichos contmles. Por ningun molivo trate det eliminar la fund6n de los controtes que exigen la presencia del operador. ENTRENAMIENTO: = Lea este manual del operador cuidadosamente. Familiarfcese con los oontroles y aprenda a operar su segadora en forma adecuadaoAprenda a parar su segadora r_pidarnente. • No perrnita que los nifios usen su segadora. Nunca permita que los adultos operen la segadora sin contar con las instrucciones adecuadas. • Mantenga el area de operaci6n despejada de genre, especialmente de nif_ospequeAos y de animales dom_stJcos. • Use la segadora solamente para los fines pmpuestos por e{ fabricante y seg_n las explicaciones descdtas en este manual. • No opere la segadora si se ha cafdo o dafiado en cualquiera forma. Siempre repare los dafios antes de usarta_ • No use accesorios que no hayan sido recomendados por el fabricante. Et uso de dichos accesorios puede ser peligroso. ° La cuchillagim cuando el motor est& funcionando. PREPARAClON; • Siempre revise cuidadosamenteel Area que se va a segar y despejeta de todas 1aspiedras, palos, alambres, huesos y otros objetos extr'aSos.Estos objetos ser_n lanzados con ta cuchiUay pueden producir lesiones graves. • Siempre use anteojos de segufidad o protectores de ojos cuandoarranque y durante el tiempo que use la segadora. 18 - Vfstase en forma adecuada. No opere la segadora sin zapatos o con sandalias mientras que el motor est,. funcionando_ o Siegue siempre durante el dfa o con buena luz artificial. OPERACION: - Mantenga sus ojos y su mente en la segadora yen el _rea que se est,. cortandoo No permita que otros intereses Io distraigan. - No corte c_sped mojado o resbaloso. Nunca corra mientras est6 operando su segadora. Siempre aseg_Sresede mantener el equilibrio - mantenga el mango agarrado firmemente y camineo ° No ponga las manos o los pies cerca odebajo de las partes rotatoriaso Mant_ngase atejado de la abertura de descarga en todo momento. o Siempre pare el motor cuando se vaya ocuando no est6 usando su segadora, o antes de atravesar las entradas para autos, los senderos, caminos y _.reas cubiertas de ripio. • Nunca dirija la descarga del material hacia los espectadores ni permita a nadie cerca de la segadora mientras la est6 operando. • Antes de limpiar, inspeccionar o de reparar I a segadora, pare el motor y est6 completamente seguro de que ia cuchilla y que todas las partes que se mueven se hayan detenido. Luego, desconecte el alambre de la bujia y mant_ngalo alejado de 6sta para evitar e! arranque por accidente_ ° No contintJe haciendo funcionar su segadora si le pega a un objeto extrafio. Siga e!_,, procedimiento desorito anteriormente, luego repare cuatquier daSo antes de volver a arrancar y de operar su segadora. ° No cambie los ajustes del regulador o hagaque el motor ande a una velocidad excesiva. Se pueden producir dafios en el motor y I esiones personales. • No opere su segadora si vibra fuera de Io normal. La vibraci6n excesiva es una indicaci6n de dafio; pare el motor, revise en forrna segura la causa de la vibraci6n y haga las reparaciones seg6n sea necesario. ° No haga funcionar el motor en recintoscerrados. Los gases de escape son petigrososo o Nunca corte el c_sped tirando la segadora hacia usted. Siegue a trav6s de la cara de las pendientes, nunca hacia arriba o hacia abajo pues puede perder el equilibrio. No siegue pendientes demasiado empinadas. Tenga cuidado cuando opere ta segadora en terreno disparejo o cuando cambie de direcci6n - mantenga un buen equilibrio. o Nunca opere Jasegadora sin las protecciones adecuadas, las planchas, el recogedor de c_sped y otros dispositivos de seguridad en su lugar_ MANTENIMIENTO Y ALMACENAMIENTO: ° Revise la cuchillay los pemos de montaje del motor a menudo, para asegurarse que estdn apretados en ]a forma adecuada. • Revise todos los pemos, tuercas y tomillos a intervalos frecuentes, para verificar si est_.n apretados en forma adecuada, y asegurarseque la segadora se encuentra en condiciones de funcionamiento seguro. ° Mantenga todos los dispositivos de seguridad en su lugar y listos para funcionar. ° Para reducir el petigro de incendio, mantenga el motor sin c_sped, hojas y grasa o aceite en excesoo ° Revise el recogedor de c6sped a menudo para verificar si hay deterioro y desgaste y cambie tas bolsas desgastadaso Use solamente las bolsas de repuesto recomendadas per el fabricante de su segadora o que cumplen con las especificaciones de _ste. ° Siempre mantenga una cuchilla afilada en su segadora. . o Siempre permita ctue el motor se enfrfe antes de guardada en cualquier recinto cerrado. ° Nunca guarde la segadora con combustible en el estanque dentro de un edificio endonde los gases pueden alcanzar una llama expuesta o una fuente de ignici6n, tal como el calentador de agua, la estufa de calefacci6n, la secadora de ropa, etc. PRECAUCI6N: Siempre desconecte el alambre de la bujfa y p6ngalo donde no pueda entrar en contacto con la bujfa, para evitar el arranque por accidente, durante la preparaci6n, el transporte, el ajuste o cuando se hacen reparaciones. PRECAUCION: Es conocido por el Esta;do de Califomia que los gases de escape del motor de este productor contienen qufmicos los cuales a ciertos niveles, pueden ocasionar, c&ncer, defectos de nacimiento, y otros dafios al sistema reproductivo. 19 Estos accesorios estaban disponibles cuando se produjo la segadora. Tambi_n est_i.ndisponibles en la mayoria de las tiendas de Sears yen los centros de servicio. La mayoffa de las tiendas Sears tambi_n pueden mandar a pedir partes de repuesto para usted, si les proporciona el n_mero det modelo de su segadora, Algunos de estos accesorios tal vez no se apliquen a su segadora. RE,NDIMIENTO DE LA SEGADORA DESVIADOR ......... : DE RECORTES PARA SEGADORAS CON DESCARGA TRASERA ESTABtLIZADORES JUEGOS PARA LA ACOLC,HADORA .................. RECOREDOR PARA SEGADORAS CON DESCARGA TRASERA MANTENIMIENTO PARA SEGADORAS CON DESCARGA RECOREDOR LATERAL DE LA SEGADORA BUJfAS SILENCIADORES CORREAS ENVASES DE GASOLINA CUCHILLAS ADAPTADORES DE CUCHILLA Lea estas instruccionesy este manual completamente antes de tratarde rnontar u operar su segadora nuev_LSu segadora nueva ha sido montada en la f&brica con la excepci6n de aquellas partes que se dejaron sin montar por razones de envfo. Todas las partes como las tuercas, las arandelas, los pemos, etc., que son necesarias para completar el montaje han sido colocadas en la bolsa de partes. Para asegurarse que su segadora funcione en forma segura y adecuada, todas las parles y los artfculos de ferreterfa que se monten tienen que ser apretados seguramente. Use las herrarnientas correctas,como sea necesado, para asegurar que se aprieten adecuadamente. PARA REMOVER LA SEGADORA DE LA CAJA DE CARTON ., RUEDAS ACF.JTE DEL MOTOR • Haga rodar la segadora hacia afuera de ia caja de cart6n y revfselacuidadosamente para verificar si todavi'a quedan partes sueltas adicionales. COMO PREPARAR SU SEGADORA PARA DESDOBLAR EL MANGO IMPORTANTE: Despliegueel mango con mucho cuidadopara no pellizcaro dafiar los cabtes de control. • Levante los mangos hasta que ta secci6n del mango inferior se asegure en su lugar, en la posici6n para segar. , t.evante la secciOndel mango superior hasta st] tugar en el mango inferior, remueva la curia protect'eray apriete ambas manillas del mango. ° Remueva la curia del mango que sujeta la barra de los control que exige la presencia del operador junto con el mango superior. • El mango de la segadora puede ajustarse segL_n le acomode para segar_Refi_rase a "AJUSTE DEL MANGO" en la Secci6n de Servicio y Ajustes de este manual, • Remueva las partes sueltas que se incluyen con la segadorao ° Corte las dos esquinas de los extremos de la caja de cart6n y tienda el panel del extremo piano. ° Remueva todo el material de empaque, excepto la cuRa entre el mango superior y _1inferior, y la curia que sujeta la barra de los control que exige la presencia del operadorjunto con el mango superior. 20 Barradecontrolqueexigela presencia deloperado o Deslice la costura igual al rededor del marco tubular, al mismo tiempo trabaje el marco adentro del recogedor de c_spedo ° Monte el marco inferior al marco tubular como demostrado. o Deslice los sugetadores de vinilio sobre el marco. Mangosuperior Levantar Aviso: Si los sujetadores de vinilio est&n muy duros, m_talos en agua caliente. costura para segar marco tubular _\ Mango inferior PARA INSTALAR LOS ACCESORIOS Su segadora rue enviada listapara usarse como una acolchadora de capa vegetal. Para conve_rla de modo que pueda ensacar o descargan ° Abra la puerta tr',,_seray remueva la tapon acolchadora. Gu&rdeta en un lugar seguroo ° Ahora puede instalar el recogedor o el desviador de recortes opcionaL • Para volver a la operaciSn de acotchamiento con capa vegetal, instale la tapon acolchadora en la abertura de descarga de la segadora_ Aseg_3rese de que todas las orejas est6n asentadas en forma adecuada. tapa soltable marco inferior (los marcos deben estar completamente marco tubular bastidor Tapon alcolchadora PRECAUClON: No haga funcionar su segadora sin la tapon acolchadora aprobada en su lugar, o sin et desviador de recortes, o sin el recogedor de c_sped, aprobados, en su lugar. Nunca trate de operar la segadora cuando se ha removido la puerta trasera o cuando est_ un poco abierta. PARA MONTAR EL RECOGEDOFI DE CESPED ° Inserta la pierna del marco tubular en la abertura del recogedor de c_sped y deslice lo entre la costura de la bolsa. Aviso: Mantenga ta costura de la bolsa recogida sobre la pierna recta del marco. ° Cuando el marco salga del otto lado de la costura, inserta inmediatamente el extremo del marco adentro de la bolsa como mostrado en la intercalaci6n. 21 FAMILIARICESE CON SU SEGADORA LEA ESTE MANUAL DEL DUEt_O Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU SEGADORA, Compare las ilustradonescon su segadora para familiarizarse con la ubicaci6n de los dk'ersos controles y ajustes, Guarde este manual para referencia en el future. producto. Aprenda y comprenda sus significados. ATTENC|{_N O ADVERTENCIA MOTOR ENCENDIO0 MOTOR APAGAO0 FL_PtDO LENTO ESTRANGU LACION Cable de control de zona del motor COMBUSTIBLE ACEITE PEUGRO, GUARDE LAS MANOS Y LOS PIES LEJOS de control que exige fa presencia det operador Control de impulsi6n CordSn Manilla del Tapa del deposito de aceite del motor con varilla indicadora de nivel mango Recogedordelc6sped Cubierta de la impulsi6n Ajustador de la rueda (en cada rueda) Tapon de la acolchadera Tapa del deposito de la gasolina caja Cebador CUMPLE CON LOS REQUISITOS DE SEGURIDAD-DE _CPSC ................................ "................ '_ Las segadoras a motor, que se conducen desde la parte de atrds, rotatorias, Sears, cumpien con los estdndares de seguridad del American National Standards Institute y de la U,S. Consumer Product Safety Commission. La cuchilla gira cuando el motor est& funcionando. Barra de con{rol que exige la prencia del operador - tiene que sujetar-se abajo, junto con el mango, para hacer arrancar el motor. Sudltela para parar el motor, Cebador - bombea combustible adicional desde el carburador al cilindro para uso cuando se necesita hacer arrancar un motor frfo. Corddn arrancadorarrancar et motor. Palanca de control de la impulsi6n - se usa para enganchar la segadora para movimiento hacia adelante tmpulsada a motor. Tapon de la acolchadera - situada en ia abertura de la descarga y debe set quitada cuando se convierte la operacci6n de ensacado a descargao se usa para hacer 22 La operaci6n de cualquier segadora puede hacer que salten objetos extrafios dentro de sus ojos, Io que puede producir dafios graves en _stos. Siempre use anteojos de segufidad o protecci6n para los ojos mientras opere su segadora o cuando haga ajustes o reparaciones. Recomendamos una mascara de seguridad de visi6n amptia, para uso espejuelos o anteojos de seguridad estandarte. COMO USAR SU SEGADORA PRECAUCI6N: No haga funcionar su_ segadora sin el desviador de recorteso sin el recogedor de c_sped, aprobados, en su lugar. Nunca trate de operar ta segadora cuando se ha removido la puerta trasera o cuando est_ un poco abierta. VELOCIDAD DEL MOTOR La velocidad det motor se estableci6 en ta f&brica para un rendimiento 6ptimo_ La vetocidad no se puede ajustar. CONTROL DE ZONA DEL MOTOR PRECAUCI6N: Las regulaciones federales exigen que se instale un control para el motor en esta segadora para reducir a un mfnimo el riesgo de lesionarse debido at contacto con la cuchilla. Por ningL_nmotivo trate de eliminar la funci6n del control del operador, La cuchilla gira cuando el motor est,:5,funcionando. • Su segadora viene equipada con una barra de control que exige la presencia del operador, Io que requiere que el operador est_ detras del mango de la segadora para hacerla arr_ficar y operada_ PARA AJUSTAR LA ALTLIRA DE CORTE ° Levante las ruedas para et corte bajo y baje las ruedas para el corte alto. o Ajuste la altura de corte para que se acomode a sus requis_tosoLa posid6n del medio es la mejor para la mayon'a de los c_spedeso • Para cambiar la altura de corLe, empuje ta patar_',.adel ajustador hacia la rueda. Mueva la rueda hacia arriba o hacia abajo de modo que se acomode a sus requisitos. AsegSrese que todas las medas queden igualmente ajustadas. ATENClON: Et ajustador esta correctamente colocado cuando las orejas de la placa est_.n insertadas en el agujero del mango. Para un corte alto, baje las ruedas Orejas de la placa Mango Para un corte bajo, levante las ruedas PARA MONTAR Y ADJUNTAR El. RECOGEDOR DE CE_SPED o Cierre ta tapa soltabte. La tapa sortable debe estar cerrada cuando se esta operando la segadora. o Levante la puerta trasera de la caja de la segadora y ponga el bastidor del recogedor de c_sped en las orejas formadas en el puntal de bisagra de la puerta trasera. = El recogedor de c_sped esta asegurado en la caja de la segadora cuando se baja la puerta trasera para descansar en el bastidor del recogedor de c_sped PREOAUCl6N: No haga funcionar su segadora sin el desviador de recortes o sin el recogedor de c_sped, aprobados, en su tugar. Nunca trate de operar !a segadora cuando se ha removido la pi_erta trasera o cuando est_ un poco abierta. Puerta trasera Puntal de Bastidor del bisagra reogedor del cesped Orejas formadas PARA VACIAR EL RECOGEDOR DE ClaSPED ° Pard remover el recog,edor del c_.spedsuelte la barra de control del operador para poder parar el • motor. ° Levante la puerta de arras y remova el recogedor del c_sped por el mango. AVISO: No arrastre la bolsa cuando la vacfe; se producir_ un desgaste innecesario. Tambi_n, los ajustes de 9 posiciones (si equipado) perrniten que el mango pueda ser movido entre las orejas de la ptaca. 23 ahi en adelanteo Puede necesitar cambiar e! aceite m_.s a menudo cuando las condiciones son polvorosas o sucias. CONTROL DE LA IMPULSION ° La autoimpulsi6n se controla al sujetar la barra de control que eyJgela presencia del operador hacia abajo en el mango y al empujar la palanca de control de la impulsi6n hacia adelante hasta que suene "clic," tuego se suetta la palancao o El movimiento hacia adelante parar_ cuando la barra de control que exige la presencia del operador se suetta. Para parar el movimiento hacia adelante sin par'-_ el motor, sualte la barra de control que exige la presencia det operador un poco hasta que se desenganche el control de la impulsi6n. Sujete la barra de control que eyJgela presencia del operador abajo en contra del mango para continuar segando sin autoimpulsi6n. ° Para mantener el control de la impulsi6n enganchado cuando se de vuelta en las esquinas, empuje el mango hacia abajo y levante las naedasdelanteras fuera del suelo al girar la segadora. ! control de \_ la impulsidn control de la impulsi6n para enganchar el control de la impulsi6n control de la impulsi6n desenganchado ANTES DE HACER ARRANOAR EL MOTOR ACEITE Su segadora fue enviada sin aceite en el motor. , Aseg_rese que la segadora est_ nivelada y que el _rea alrededor del dep6sito de aceite est_ limpia. ° Remueva la tapa del dep6sito de aceite del motor con la vari!la indicadora de nivel y rellene hasta ta linea de lleno en _sta. ° Use 20 oz. de aceiteo Para el tipo y la calidad vea "MOTOR" en la secci6n de las Responsabilidades del Cliente en este manual. ° Vacie et aceite lentamente. No !o llene demasiado. ° Revise et nivel del aceite antes de cada uso. Agregue aceite si es necesado. Llene hasta la linea de Ileno en la varilla indicadora de nivel,, ° Para leer el nivel adecuado, apriete la tapa del dep6sito de aceite del motor cada vez. , Vuelva a instatar la tapa del dep6sito del aceite y apri6tela,, ° Despu_s de las dos (2) primeras horas de siega, cambie el aceite y cada 25 horas de GASOLINA o Ueneel estanque de combustible. Use gasolina regular, sin plomo, nueva y limpia con el mfnimo de 87 octanos. (El uso de gasolina con plomo aumentar& los dep6sitos de 6xido de plomo y cad_onoy se reducir& la duraci6n de la v_vuta)o No mezcle el aceite con la gasolina. Para asegurar que la gasolina utilizada sea fresca compre estanques los cuales puedan ser utilizados durante los pdmeros 30 dfas. IMPORTANTE: CUANDO SE OPERE EN TEMPERATURAS POR DEBAJO DE 32° F (0 ° C) USE GASOLINA DE CALIDAD DE INVIERNO, UMPIAY NUEVA PARAAYUDAR AASEGURAR UN BUEN ARRANQUE EN CLIMA FRIO. ADVERTENCIA: La experiencia ha indicado que los combustibles mezclados con alcohol (conocidos como gasohol, o el uso de etanol o metanol) pueden atraer la humedad, la que conduce a la separaci6n y formaci6n de _cidos durante el almacenamiento. La gasolina ac{dica puede dafiar el sistema del combustible de un motor durante el almacenarniento. Para ev'rlarlos problemas con el motor, se debe vaciar el sistema de combustible antes de guardarlo por un peffodo de 30 di'as o m_. Vacfe el estanque de combustible, haga amancar el motor y h_galo funcionar hasta que las Ifneas del combustible y el carburador queden vacioso La prOxima temporada use combustible nuevo°Vea las lnstrdcciones para el Almacenamiento para mrs informaci6n. Nunca use productos de limpieza para el motor o para el carburador en e! estanque del combustible pues se pueden producir dafios pen'nanentes. PRECAUCI6N: Uene hasta ta parte inferior del cuello de relleno del estanque de gasolina. No to Ilene demasiado. Umpie el aceite o el combustible derramado. No almacene, derrame o use gasolina cerca de una llama expuesta. Tapa del deposito de ia gasolina 24 Tapa del deposito de aceite det motor con varilla indicadora de , nivel # PARA HACER ARRANCAR EL MOTOR CONSEJOS PARA SEGAR Y ACOLCHAR * Para hacerarrancar un motorfn'o, empuje el cebador tres (3) veces antes de tratarlo. Empuje firmementeo Este paso normalmente no es necesario cuando se hace arrancar un motor que ya ha estado funcionando por unos cuantos minutos. ° Sujete la barra de control que exige la presencia del operador abajo en el mango y tire el mango del arrancador r_pidamenteo No perrnita que el co_6n arrancador se devuelva abruptamente. o Para parar el motor, suelte ta barra de control que eyJge la presencia del operador. IMPORTANTE: Para ebtener el mejorrendimeinto mantenga la caja de la segador a sin acumladon de cesped y basura_Vea "LIMPIEZA" en seccion de"RESPONSABILIDADES DEL CLIENTE" de este manual.. AVISO: En climas m_,sfrfos puede que sea necesario repetir los pasos del cebado. En climas m_,s calurosos et cebar demasiado puede producir el ahogo y el motor no va a arrancar. Si se ahoga e! motor espere unos cuantos minutos antes de tratar de hacedo arrancar y no repita los pasos del cebado, CONSEJOS PARA SEGAR ° Bajo ciertas condiciones, tal como c_sped muy alto, puede ser necesario el elevar la altura del corte para reducir el esfuerzo necesario para empujar la segadora y para evitar sobrecargar el motor, dejando montones de recortes de c6sped. Puede que sea necesario redudr la velocidad del recomdo y/o haga funcionar la segadora sobre el &rea porsegunda vez. ° Para un corte muy pesado, reduzca el ancho det corte pasando parcialmente por encima del lugar anteriormente cortado y siegue lentamente. ° Cuando use una segadora con descarga trasera en c6sped h0medo y pesado, los montones del c6sped cortado puede que no entrenen el r_.,ogedor de c6sped. Reduzca la ve[oc[dad del recorfido (ve[ocidad de empuje) y/o haga funcionar la segadora sobre el _rea por segunda vez. ° Si queda una huetla de cortes en el lado derecho de una segadora con descarga trasera, siegue en la direcd6n en que giran las manillas del reloj, solapando un poco para recaudar los recortes en la pr6xima pasada. ° Los poros en los recogedores de c6sped de tela pueden Ilenarse con mugre y polvocon el uso y los recogedores recaudar'&nmenos c6sped. Para evitar 6sto, roc[e el recogedor con la manguera de agua reguIarmente y d6jelo secarse antes de usarlo. ° Mantenga la parte superior del motor, alrededor del arrancador, despejada y sin recortes de c6sped y paja. Esto ayudar& el ftujo del aire del motor y extender'& su duraci6no ° La cuchi[la acolchadora especial va a volver a cortar los recortes de c6sped muchas veces, y los reduce en tamaSo, de modo que si se caen en el c_sped se van a dispesar entre _ste y no se van a notar. Tambi_n, el c6sped acolchado se va a deshacer r_pidamente entregando substancias nutritivas para el c_sped. Siempre acolche con la veloddad del motor (cuchi[la) m_s atta, pues asf se obtendr_ la mejor acci6n de recorte de las cuchillas. - E_e cor'_r el c_sped cuando est6 mojado. [] c_sped mojado tiende a formar montones e interfiere con la acci6n de acotchado. La mejor hora para segar el c6sped es temprano en la tarde. A esa hora 6ste se ha secado y el _rea reci6n cortada no quedar& expuesta al sol directo. ° Para obtener los mejores resultados, ajuste la altura del corte de ta segadora de modo que 6sta corte solamente el tercio superior de las hojas de c6sped. En el caso de que el c_sped haya cr_-_do demasiado, puede ser necesario el elevar la altura del corte para reducirel esfuerzo necesario para empujar la segadora y para evitar sobr_..argar el motor, dejando montones de recortes de c6spedo Para un acolchamiento muy pesado, reduzca el ancho det torte pasando por encima del lugar antefiormente cortado y siegue lentamente. o Ciertos tipos de c6sped y sus condiciones pueden exigir que un _rea tenga que ser acolchada por segunda vez para esconder completamente los recortes_Cuando se haga el segundo corte, siegue atravesado o en forma perpendicular a la pasada del primer corte. - Carnbie su patr6n de corte de_semana a semar,,a.Siegue de norte a sur una semana y luego cambie de este a oeste la pr6xima sernana. Esto evitar_ que el c_sped se enrede y cambie de direcci6n Max, 1/3 25 ......................................................... __,_o_'_,_ S E Revisarsihaysuietadores sueftos Ltmpiariinspeccionar el recogedor de c_sped(sivieneequipado) Limp_ar'"i'a segado_-a ..... b/ _ _ - G umpi_'r debai,:, d;,'"'i_'Cub_ert_ la,ra._mtsf6n(segadoras conpoder_, propuisor) D AS_ S.RWC,O _ '. _4...... .......... Rev|sarlascorreas y laspoleasimpulsaoas {segadoras con poder propu/sor) _ i.o.,,i_., o/a, iarica.,bi", Ja,:u_.,,_, J .o ,oB, .... T__ a I 2 3 4 I _, (segadoras con arrallque e[_ctrico} ...............:........... !_ ::........ V'i ........................... I J3 :Limpi:arla baterfairecargar ......................... Carnbiarel aceitedelmotor Limptar eliiiiro d_aire ''_`'....... _ I '1 ...... : ...... _4 ........ .................. :................................................................................ ................. j v' .... Limpiar olcambiaria bui_a ,,,iiii,i Cambiar el cartucho de papeldelfiitro de _lre ..... if _'2 - Cambtarrn_ a rnenudocuandoseopere baJocargapesadao en _rnbtentes conaltas temperaturas,, - D_ servt_iom_,sa menudo cue_doso opera en condictonessuctaso po/vorosas, - Camb{elascuchillasm_s a menudo cuandoStegUeen Ierreno arenoso, - Cmgar por 48 horasa! lin de la temporada.. RECOMENDACIONES TABLA DE LUBRICACION GENERALES La garantra de esta segadora no cubre los art_culos que han estado sujetos al abuso o a la negligencia del operador. Para recibir todo el valor de la garant[a, el operador tiene que mantener ia segadora seg_n las instrucciones descritas en este manual. .(_) Ajustadpr de ;a rueda Aceite del motor Hay algunos ajustes que se tienen que hacer en forma pedSdica para poder mantener su unidad adecuadamente. Todos los ajustes en la secci6n de Servicio y Ajustes de este manual tienen que set revisados por 1omenos un vez pot cada temporada. • Una vez al a5o, cambie la bujla, limpie o cambie el elemento del filtro de aire y revise si la cuchilla est,. desgastada. Una buji'a nueva y [,n elemento de] filtro de aire limpio/ nuevo aseguran la m.ezcla de aire-combustible adecuada y ayudan a que su motor funcione mejor y que dure mdso , Siga el programa de mantenimiento en este manual. ANTES DE CADA USO o Revise el nivel del aceite del motor. o Revise si hay sujetadores sueltos. LUBRlCACION Mantenga la unidad bien lubdcada (yea ta "TABLA DE LUBRICACION"). (_) Bisagra de la (_) Clavija de montaje del puntal del mango puerta trasera REFtERASE A LA SECCION DE ROCIE EL LUBRICANTE RESPONSABILIDADES DEL CLIENTE EN "MOTOR" IMPORTANTE: No acerit o engrase los rodamientos de la rueda de plastico. Los lubricantes viscosos atraeran polve y mugra, Io que acortara ta duracion de los rodamientos auto lubricantes. Si cree que lubricarse, use solamente un lubricante tipo grafito, de polve seco, en forma moderada° 26 ESPECIRCACIONES DEL PRODUCTO _IOMERO DE MODELO 917.377520 _IOMERO DE SERIE FECHA DE COMPRA CABALLOS DE FUERZA: 5.0 DESPLAZAMIENTO: 11.5 CU. IN. CAPACIDAD Y TIPO 1.6 Cuartos DE GASOLINA: REGULAR TIPO DE ACEtTE: (APi-SF/SG) SAE 30 (sobre 32°F) SAE 5W-30 (debajo 32°F) CAPACIDAD DE ACEITE: 20 oz. de capacidad BUJiA (ABERTURA: CHAMPION TOLERANCIA SENCENDIDO SOLIDO TORSION ,030") DE VALVULA: SIN PLOMO RJ19LM OR J19LM ADMISION: .005" DESCARGA: .007" DE ESTADO ABERTURA DE AIRE: .010 IN. DEL PERNO DE LA CUCHILLA: 35-40 FT. LBS. o El num_ro del nodelo y el de serie se encuentran en la calcomania adjunta a la parte trasera de la caja de la segadora. Debe registrar tanto el num_ro de serie come la fecha de compra y mantengalos en un lugar seguro para refencia en et futuro. SEGADORA Siempre observe las reglas de seguridad cuando haga el mantenimiento. LLANTAS . Mantenga tas Ilantas sin gasolina, aceite o substancias qufmicas para control de insectos que pueden da_ar la goma. o Evite los tocones, las piedras, las grietas profundas, los objetos afilados y otros peligms que pueden daSar alas !lantas. CUIDADO DE LA CUCHILLA Para obtener los mejores resultados,la cuchilla de la segadora tiene que mantenerse afilada. Cambie la cuchitla doblada o dafiada. PAPA REMOVER LA CUCHILLA o Desconecte el alambre de la bujfa y p6ngalo en donde no pueda entrar en contacto con _sta. = Haga descansar la segadora en su lado. Aseg(Jrese que el fiitro de aire y que el carburador queden mirando hacia arriba. ° Use un bloque de madera entre la cuchilla y la caja de la segadom para evitar que la cuchilla gire cuando se le quite el pemoo ° Proteja sus manos con guantes y/o envuelva la cuchilla con una tela gruesa. ° Remueva el pemo de la cuchilla gir&ndolo en el sentido contrario en que giran las manillas del reloj. ° Remueva la cuchiUay los artfculos de ferreterfa adjuntadores (el pemo, la arandela de seguridad y la arandela enduredda)o AVISO: Remueva el adaptador de la cuchilla y revise el cubo interior de la ranura del adaptador de la cuchil[a. La ranura tiene que estar en buenas condiciones para que funcione en forma adecuada. Cambie el adaptador si est& dafiado. PARA CAMBIAR LA CUCHILLA ° Ponga el adaptador de la cuchilla en el ciguefial del motor. AsegSrese que ta ranura del adaptador y que el chaveterodel ciguefiai est_n alineados° = Ponga la cuchilla en el adaptador de _sta aiineando los dos (2) agujeros en la cuchi!la con las salientes elevadas en el adaptador. ° AsegSrese de que el borde de salida de la cuchilla (opuesto al borde afilado) est_ hada ardba hacia el motor. • Instale el pemo de la cuch_la con la arandela de seguridad y la arandela endurecida en el adaptador de la cuchilla y el cigueSaL 27 ', Use un bloque de madera entre la cuchilla y la caja de ta segadora y apriete et pemo de la cuchilla gi_ndolo en el sentido en que giran las manillas del reloj. • , La torsion para apretar recomendada es de 3540 pies libraso IMPORTANTE: EL PERNO DE LA CUCHILLA ES CLASE 8 TRATADO A CALOR. AVISO: No recomendamos el afilar la cuchilla -pero si !o hace, asegt_resede que quede balanceada. PARAAFtLAR LA CUCHtLLA Se tiene que tener cuidad0 de manteneda batanceada. Una cuchilla que no est_ balanceada va a producir eventua]mente daOoen la segadora o en el motor. o La cuchillapuede afilarse con una lima o en una rueda rectificadore. No trate de afilafla mientras se encuentra en la segadora. ° Para revisar el balance de ta oJchilla, clave un clavo en una riga o en la pared. Deje alrededor de una pulgada de un clavo i'ectoexpuesto. Ponga el agujero central de la cuchilla sobre la cabeza del davoo Si la cuchi!ta est& balanceada debe permanecer en la posiciOnhorizontal. Si cualquiera de los extremos de la cuchilla se mueve hacla abajo, afile el extremo pesado hasta que _sta quede b_ar_..eada. Adaptador de la cuchilla Chavertero det " uefial Ranura Cuchi!ta Pemo de / la cuchilla / CAJA DE ENGRANAJES ° Para mantener el sistemade impulsi6n fundonando en forma adecuada, la caja de engranajes y el _rea alrededor de la imputsi0n tienen que mantenerse limpias y sin acumulaci0n de basurao Umpie debajo de la cubierta de la impulsion dos veces por temporada_ = La caja de engranajes se llena con lubdcante hasta el nivel adecuado en la f_orica. La enica vez que el lubricante necesita atenci6n es cuando se le ha prestado seMcio a la caja de engranajes. = Si se necesita lubdcante, use solamente Grasa Texaco Starplex Premium 1, Parte No. 750355. No use substitutos. RUEDAS DE IMPULSION Revise las r,.Jedasde impulsion delanteras cada vez antes de segar,para asegurarse de que se mueven librementeo Si las ruedasno giran libremente quiere decir que hay basura, recortes de c_sped, etc. en et &rea de las ruedasde impulsi6n y tienenque limpiarse para tiberadas. Es necesafio tirnpiar las ruedas de impulsion; revise ambas ruedas delanteras. = Remueva los tapacubos, las clavijas de horquilla y tas arandelas. • Remueva las ruedas de los ajustadores de las ruedaso = Remueva la basuray los recortes de cdsped de dentro de la cubierta contra el polvo, pifOn y/o de los dientes de los engranajes de las ruedas de impulsion. • Ponga {asruedas de vuelta en su lugar_ • Si despu_s de limpiar tas ruedas de impulsi6n no giran libremente, pOngase en contacto con su centro/departarnento de servido autorizado m&s uefial cercano, MOTOR LUBRICACION de Arandela segridad Endurecida RECOGEDOR Borde de satida Adaptador de la cuchilla Use solamenteaceite de detergente de alia calidad clasificadocon la das'_caci6nSF o SG de servtcio APL Seteccione la calidad de viscostdad SAE seg_n su temperatura de operaei6n esperada. DE ClaSPED (Si comprado como un acceso_o) El recogedor de c_sped puede ser rociado con el agua de la manguera pero tiene que estar seco cuando se vaya a usar. Revise su recogedor de c_sped a menudo para verificar si est_ da,fiado o deteriorado. Se va a desgastar con el uso normal. Si se necesita cambiar el recogedor, c_mbielo solamente por uno que sea aprobado por el fabricanteo D6 el nOmerodel modelo de la segadora cuando Io ordene. CAL!DADES DE VISCO$1DAD DE SAE ,__mmmm o =o" _, 40. ' G0, " _, °c ,,,oo" -20',.... -to" o, lo' _' " i_' _" 40" GAMA D€: TEMPERATURA ANTtC1PADA ANTES OEL PROXIMO CAMBIO DE ACEI_E AVISO: A pesar de que los aceites de multiviscosidad (5W30, 10W30, etc.) mejoran el arranque en clima frt'o,estos aceites de rnultMscosidad van ha aumentar et consurno de aceite cuando se usan en temperaturas sobre 32° F. Revise el nivel del aceite del motor m__sa menudo, para evitar un posibte daOo en el motor, debido a que no tiene suficiente aceiteo 28 plancha trase_ Cambie e[ aceite despu_s de 25 horas de operaci6n o por Io menos una vez al &rio si ta segadora se utiliza menos 25 horas el afioo Revise el nivel del aceite del c&rter antes de arrancar el motory despu_s de cada cinco (5) horas de uso continuado, Apriete el tap6n del aceite en forrna segura cada vez que revise el nfvel del aceite. labio ranuras PARA CAMBIAR ELACEtTE DEL MOTOR AVISO: Antes de inclinar la segadora para drenar el aceite, drene el tanque de combustible haciendo correr el motor hasta que el tanque est6 vacio. o Desconecte el alambre de ta bujfa y p6ngalo de modo clueno pueda entrar en contacto con _sta, o Remueva la tapa del dep6sito del aceite; d_jela a un lado en una superficie limpia, • Incline la segadora y h_,galadescansar en su lado y drene el aceite en un envase adecuado. Mueva la segadora de atr&s para adelante para remover todo el aceite que se haya quedado atrapado dentro del motor. • Umpie todo el ace_e derramado en la segadora y en el lado del motor, o Uene el motor con aceite. U6nelo solamente hasta la Ifnea de tleno (FULL) en la varitla indicadora de niveL NO LO LLENE DEMASIADO, - Vuelva a poner la tapa en el dep6sito del aceite° ° Vuelva a conectar el alambre de la bujfa a _sta. Envase FILTRO DE AIRE Su motor no fundonar_, en forma adecuada y puede sufrir dafios si se usa un filtro de aire sucio. Cambie el filtro de aire cada aSo, y m&s a menudo si siega en condiciones muy polvorosas o sucias,, No lave el filtro de aire. PARA CAMBtAR EL FILTRO DE AIRE ° Suelte el tomillo e incline la cubierta para removerlo. = Cuidadosamente, remueva el cartucho. • Lfmpielo golpedndoto suavemente en una superficie plan& Si est_ muy sucio cambie el cartucho.. PRECAUCION: Los solventes de petr61eo, tales como el keroseno, no se deben usar para limpiar el cartucho. Pueden producir el deterioro de _steo No aceite el cartuchoo No use aire a presi6n para limpiarlo o secarlo. - Instale et cartucho, luego vuelva a poner la cubierta asegurAndose que las orejas est_n alineadas con las ranur_ en'la plancha trase_ Apriete et tomitto en forrna segur& orejas de la cubierta caflucho cubierta SILENCIADOR Inspeccioney cambie el silenciador si est,. corm[do pues producir un peligro de incendio y/o dafio. BUJIA Cambie su bujfa cada a5o para hacer que su motor arranquem&s f&cilmente y fundone mejor. Ajuste la abertura de la bujfa en 0.030 pulgadao LIMPIEZA tMPORT_TrE: Para obtenerel mejor redimientom, mantenga lacajadetasgadorasin acumulacion de cesped y gasuraoUmpie la parte de su segadora despues de cada uso. PRECAUCI6N: Desconecte el alambre de la bujfa y p6ngalo en donde no pueda entrar en contacto con _sta. o Haga descansar la segadora en su lado. Aseg_rese que el filtro de aire y que el carburador queden mirando hacia arribao Umpie la parle inferior de su segadora rasp_indola para remover la acumulad6n de c_sped y basura. ° Umpie el motor a men{Jdopara evitar que se acumule la basura. Un motor tapado funciona m_is caliente y se acorta su durad6n. ° Mantenga las supe_cies pulidas y las ru_as sin gasolina, aceite, etc. ° No recomendamos el uso de una manguera de jardfn para limpiar la segadora a menos que el sistema el_ctrico, el silenciador, el filtro de aire y el carburador est_n tapados para evitar que tes entre el agua. [] agua en el motor puede acortar la duraci6n de _ste. LIMPIE DEBAJO DE LA CUB1ERTA DE LA IMPULSI6N Umpie debajo de la cubiertade la impulsi6npor Io menos dos veces cada temporad& Raspe debajo de la cubierta con un cuch_lo para masilla o con una herramienta parecida, para remover toda acumulaci6n de c_sped o basura en la parte iv,ferior de la cubierta de la impulsi6n, 29 PRECAUCION: ANTES DE DAR CUALQUIER SERVICIO 0 DE HACER AJUSTES: ° Suelte la barra de control y pare el motor° , Aseg0rese que la cuchUlay que todas las partes movibles se hayan detenido completa.mente. ° Desconecte el alambre de la bujfa y p6ngalo en donde no pueda entrar en contacto con _sta. SEGADORA PAPA AJUSTAR LA ALTURA DE CORTE Vea"PARAAJUSTAR LAALTURADE CORTE" en la secci6n de Operad6n de e_"temanual. DESVIADOR TRASERO Se proporrJona un desviadortrasero,adjunto entre las ruedastraseras de su segadora, para reducir a un mfnimo la posibilidad clueobjetos sean tanzados hacia afuera de la parte trasera de la segadora, en la posici6n en donde se encuentra el operador. Si se da6a et desviador debe cambiarse. PARA REMOVEPJCAMBIAR LA CORREA DE IMPULSION ° Remueva la cubierta de la impulsi6n.Remueva la correa empujando hacia abajo en ta polea de ( la caja de engranajes. ° Haga descansar la segadora en su lade con et filtro de aire y el carburador mirando hacia aniba. = Remueva la cuchilla. ° Remueva la defensa en contra del desperdicio, o Remuova la correa de la polea del motor en el ciguefiaL = Instale la correa nueva siguiendo los pasos anteriores en et orden inversoo ° Siempm use la correa aprobada per la fdbrica para asegurarse que calce y dure. ° Remueva las abrazaderas del cable. - Remueva loscontroles y la barra de control que exige la presencia del operadordel mango superior. ° Remueva la gufa del cord6n arrancador del mango inferior° ° Remueva las clavijas de horquilla. ° Desconecte el mango inferiorde los puntales del mango(, ° De vuelta el mango y'_elva a montar las davijas de horquilla que se habfan removido. o Vuelva a montar la gufa det cord6n arrancador. ° Vuelva a montar los controles y la barra de control que exige la presencia del operador en et mango superior. PRECAUClON: La barra de control que exige la presencia del operador tiene que pk_otear tibremente para permitir el enganche de ia cuchilla/freno cuando se suelta la barra de control, No apriete demdsiado los sujetadores que sujetan a los controles al mango superior, o Para carnbiar de la posid6n de mediana baja a atta solamente se tendrd que darvuelta ta secci6n del mango supedor, ° Para cambiar de la posici6n mediana baja a baja, solamente se tendrd que dar vueita la secci6n del mango inferior, Posici6n de envio Mediana baja Cubierta de la impulsion Mediana alta , Baja Correa Empujar hacia abajo PARA AJUSTAR _: EL MANGO Apriete para Se puede Iovantar o bajar elmango do su segadora seg0n le quedo cdmodo. Hay cuatro (4) posiciones disponibles: alia, mediana alta, mediana baja, baja. Los mangos se envfan montados on la posid6n mediana baja. , Para cambiar de la posici6n mediana baja a mediana alta, la secci6n superiory la inferior del mango tendrdn que darse vuelta_ Mango infedor remover Puntal del mango 30 Abrazadera de gorqui!la MOTOR VELOCIDAD DEL MOTOR CARBURADOR Su carburador no es ajustabte. Si su motor no est& funcionando en forma adec_Jada debido a problemas que se sospecha vienen del carburador, Ueve su segadora a un centre de servicio autorizado para reparada y/o ajustada. IMPORTANTE: Nunca manipulee el regulador del motor, el que ha side ajustado en lafabrica ara ia velicidaddel motor adecuada, puede ser petigroso hacer funcionar el motor a una vetocaded per sobre e! ajuste de ata velocidad alta regulada del motor necesita ajuste, pongase en contacto con su centre departamento de servicio autorazado mas cerano, el que cuenta con el equipo adecuado y la experiencia para haacer los ajustes necesarios. La velocidad del motor ha side ajustada en la f&brica. No trate de aumentar la vetocidad del motor pues se pueden producir lestones personales. Si cree que et motor est_ funcionando demasiado r&pido o demasiado lento, Ileve su segadora a un centre/ departamento de servicio autorizado para reparada o ajustada. Inmediatamente prepare su segadora para el almacenamiento al final de cada temporada o si la unidad no se va a usar per 30 dfas o m_,s. SEGADORA Barra de control que exige la presencia del operado Mango superior Cuando se va a guardar Is segadora per cierto pedodo de tiempo, lfmpiela cuidadosamente, remueva toda la mugre, la grasa, las hojas, etc. Gu_rdela en un _rea limpiay secao o Limpie toda la segadora (Vea "UMPIEZA" en ia secciSn de Responsabilidades del Cliente de este manual). • Lubfiquela seg0n se muestra an la seccidn de Responsabilidades del Cliente de este manual. ° Asegt_rese de que todas las tuercas y clavijas y todos los pemos y tomillos est_n apretados en forna segura. Inspeccione las partesclue se mueven para verificar si est_n daSadas, quebradas o desgastadas. C_'nbielas si es necesarioo • Retoque todas las superficies que est_n oxidadas o con la pintura picada;use una tija antes de pintar. MANGO Puede doblar el mango de su segadora para almacenarla. ° Apriete los extremes inferioresdel mango inferior entre sf hasta que el mango inferior quede separado del puntal de! mango, tuego mu6valo hacia adelante. o Suelte los pemos de montaje del mango superior to suficiente come para permitir que el mango superior se pueda doblar hacia atr_s. Mango inferior Puntal del mango Clavija de horquilla 31 para segar Mango inferior IMPORTANTE: Cuando doble el mango para el alacenarniento o el trasporte,asegurese que 1o doble segun se muestra o puede danar loscables de control. o Cuando prepare sue mangos a partir de la posici6n de almacenamiento, el mango inferior autom_ticamente se asegura_ en la posici6n para segac MOTOR SISTEMA DE COMBUSTIBLE tMPORTANTE: Es importante evitarque se forrnen depositosde partes fundamenta]es del sistemade comustibletalescome el carburador,el filtro del combutible,la manguera del combustibleo en el estanquedurante el aimacenmienfo.La experienceatambien endica que toscombustibles mezclados con alcohol (conocido come gasohol o que tienen etanol o metanol) pueden atraer humedad, Io que conduce a la separati6n y a la formaci6n de dcidosdurante almacemamiento, la gaso_ina&cideca puede naSar et sistema de combustible de un motor durante el peridode alcarnenmiento. • Dreneelestanque decombustible. o Hagaarrancar elmotoryd_ji_lo funcionar hasta quelaslineasdelcombustible yelcarburador est_nvacfos° ° Nunca use los productos para limpieza del carburador o del motor en el estanque de combustible pues se pueden producir dafios permanentes. o Use combustible nuevo la prOxima temporadao AVISO: E1estabilizador de combustible es una altemativa aceptabte para reducir a un mfnimo la formaci6n de depSsitos de goma en el combustible durante el perfodo de almacenamiento. Agregue estabilizador a la gasolina en el estanque de combustible o en el envase para el almacenamiento. Siempre siga la proporci6n de mezcla que se encuentra en el envase del estabilizador. Haga funcionar el motor por Io menos 10 minutos despu_s de agregar el estabilizador, para perrnitir que este ilegue al carburadoro No drene ta gasolina del estanque de gasolina y el carburador si se est& usando estabilizador de combustible. ACEITE DEL MOTOR Drene el aceite (con el motor catiente) y c_mbielo con aceite de motor timpio. (Vea =MOTOR" en la secciOnde Responsabilidades del Cliente de este manual..) CILINDRO , Remueva la bujia. ° Vacie una onza (29 ml) de aceite a tray, s del agujero de la bujfa en el cilindro. ° Tire la manilla de arm,_qquelentamente unas cuantas veces para distribuir el aceite. • Vuelva a montar la nueva bujfa. OTROS ° No guarde la gasolina de una temporada a la otra. ° Cambie e! envase de la gasolina si se empieza a oxidaroLa oxidaciSn y/o la mugre en su gasolina producir&n problemas. ° Si es posible, guarde su unidad en un recinto cerrado y c_brata para protegerla contra el polvo y la mugre. o Cubra su unidad con un forro protector adecuado que no retenga la humedad. No use pl_stico. El pt_stico no puede respirar, Io que permite la formacidn de condensaciSn, to que producir'&la oxidaci6n de su unidad° IMPORTANTE: NUNCA CUBRA LA SEGADOP_, MIENTRAS EL MOTOR Y LAS AREAS DE ESCAPE TODAVIA ESTAN CALIENTESo PREOAUOION: Nunca almacene la segadora con gasolina en el estanque dentro de un edificio en donde los gases pueden alcanzar una llama expuesta o una chispa. Permita que se enfri'e e! motor antes de almacenarla en atgt_n recinto cerrado. 32 IDENTIFICACION DE PROBLEMAS PROBLEMA CAUSA CORRECCION No arranca o Filtro de aire sucio. ° Limpie/cambie el filtro de aireo '"" ° Sin combustible. ° Llene el estanque de combustible. ° Combustible rancio. • Drene et estanque y vuelva a Itenarfo con combustible limpio y nuevo. * Agua en el combustible° ° Drene el estanque de combustible y' el carburador y vuelva a Itenar el estanque con gasolina nueva. ° Alambre de la bujfa desconectado. ° Conecte el alambre a la bujfa. oBujfa mala. • Apriete el pemo de la cuchilla o cambie el adaptador de la cuchilla. ° Presione la barra de control ha¢ia el mango. • Cambie la barra de control° , Cambie la bujfa. * Cuchilla suelta o adaptador de la cuchilla quebrado. ° Barra de control en la posici6n suelta. Falta de fuerza - Barra de control defectuosa. Ajuste a la posici6n de "Corte m_s alto." * Parte trasera de la cajacuchilla de la segadora arrastr_ndose en el c_sped pesado. Ajuste a la posici6n de "Corte m_s alto." ° Est,. cortando mucho c_sped. o Filtro de aire sucio. * Limpie/cambie el fittro de aire. "Acumutaci6n de c_sped, hojas y basura debajo de la segadora. ° Revise el nivel det aceite. o Demasiado aceite en el motor. • Corte a una v_Jocidad de recorrido m_.s lenta. 33 ° Limpie la parte inferior de la caja de la segadora. PROBLEMA ..... _al corte -disparejo cAUSA o CuchiUa desgastada, doblada o o Cambie la cuchilla. Apriete el suelta. pemo de la cuchilta. ° Altura de las ruedas dispareja. ° Ajuste todas las ruedas a la misma altura. o Acumulaci6n de c6sped, hojas o! • Limpie la parte inferior de la caja de la segadora. basura debajo de la segadora., Vibraci6n excesiva • Cuchilla desgastada, doblada o suelta. = Ciguefial dei motor doblado. , Cambie la cuchitla. Apriete el pemo de la cuchilta. ° P6ngase en contacto con su centro de servicio autorizado m&s cercanoo ° El freno del volante del motor est,. aplicado cuando se suetta la barra de control. - CigueSat del motor doblado. ° Adaptador de la cuchilla quebrado. ° La cuchilla se arrastra en el c_sped. ° Presione la barra de control hacia el mango superior antes de tirar el cordSn arrancador. = P6ngase en contacto con su centro de servicio autorizado m_s cercano. o Cambie el adaptador de la cuchilla. _o Mueva la segadora a un lugar en donde el c_sped ha sido cortado o a una superficie firrne para hacer arrancar el motor. CordSn arrancador dificil de tirar ,,,,,,,,,,,, , i i,H ,, Recogedor de c_sped no se tlena (si viene equipado) .................. Dif[cil de empujar CORRECClC)N .......... = i i ,,,,, = Altura de corte demasiado baja. • Levantamiento de la cuchilla desgastado. = Recogedor sin ventilaci6n de aire. i,, m ° Eleve la altura de coder ° Cambie Lacuchillas. ° Limpie el recogedor de c6sped. i ,i , Et c_sped est& demaslado alto o la altura de la rueda demasiado baja. = Parte trasera de la cajalcuchilla de la segadora arrastr_ndose en el c_sped. • Recogedor de c_sped demasiado Ileno. ° Posici6n de la altura del mango no adecuada par° usted. 34 o Eleve la altura de corteo • Eleve la parte trasera de la caja d_ la segadora (1) un lugar m&s alto. • Vacfe el recogedor de c_sped. ° Ajuste la altura det mango de modo que le acomodeo ROTARY LAWN MOWER -- MODEL NO. 917.377520 GEAR CASE ASSEMBLY PART NUMBER 702511 I I KEY NO. PART NO. 17490416 2 3 4 6 137055X004 137053 57072 48373 7 8 77881 137051 DESCRIPTION KEY NO. Tapping Screw 1/4-20 x 1-!/4 Engagement Bracket Shifter Seal Gear Case Halves Kit (includes Key Noso 4, 5, and 7) Beadng Worm Shaft 9 t0 11 12 13 14 15 16 17 18 19 PART NO. 137074 57079 131484 700343 86447 137050 750436X 750369 12000003 850848 81585X004 NOTE" All component dimensions given in U.S. inches. 1 inch = 25.4 mm 35 DESCRIPTION Drive Shaft Hardened Washer Clutch Yoke Bushing Plug Helical Gear Clutch Jaw Grease E-Ring Hi-Pro Key Spring Bracket ROTARY LAWN MOWER MODEL NUMBER 917.377520 13 6 ! \ 27 22 30 10 14 5o 10, i 35 39 12 CO 37 30 56 52 4t ROTARY LAWN MOWER MODEL NUMBER 917.377520 KEY NO. PART NO. 1 2 4 5 6 8 9 10 11 12 13 14 15 16 17 18 20 22 23 25 27 28 29 30 31 32 34 35 37 !45646X479 162788 150425 66426 136376 145793 151023 128415 150050 STD512505 77400 156374X479 700365X479 133190X479 140661X479 63601 140540 84596 87677 83923 151155 142748 62335 145935X004 701037 700331X004 14663O 700326X007 150078 39 _40 151512X479 15151tX479 .= DESCRIP_ON Upper Handle Engine Zone Control Cable Mulcher Rug Cable Clip Handle Knob Control Bar Rear Door Kit Pop Rivet Self Tapping Screw #10-24 x 5/8 Hex Tapping Screw w/Sems 1/4-20 x 1/2 Hubcap Back Plate Side Baffle Discharge Baffle Rear Baffle Keps Locknut 1/4-20 Rear Skirt Engine Pulley Hi-Pro Key #505 Hex Flange Nut Wheel Shoulder Bott 3/8-16 x 1 Spring Washer Axle Arm Assembly Selector Knob Selector Spring Spacer Wheel Adjusting Bracket Thread Cutting Screw wlSems 5/16-18 x 3/4 Handle Bracket Assembly (Left) Handle Bracket Assembly (Right) KEY NO. PART NO. 41 150406 44 161769 46 47 48 49 50 851514 157101 851074 850263 851084 51 52 55 56 57 58 59 61 62 64 700869X479 85463 751592 88652 51793 157081X479 131959 132001 134612 ...... 70 -- 700327)(007 161767 DESCRIP_ON Hex Head Thread Rolling Screw 3t816 x 1-1/8 Lawn Mower Housing (Incl. Key #14, 15,51 & Blade Adapter Blade 22" Hardened Washer Helical Washer 318-24 x 1-3/8 Gr. 8 Hex Head Machine Screw 318-24 x 13/8 Gr. 8 Front Baffle Danger Decal Locknut 3/8-16 Hinge Screw 1!4-20 x 1-1/4 Hairpin Cotter Lower Handle Handle Bolt Rope Guide Debris Shield Engine - (See Breakdown) Briggs12H802-1978-E1 Wheel Adjusting Bracket Owner's Manual (English/Spanish) Available accessories not included with lawn mower: -71 33303 Clipping Deflector -_ 71 33623 Gas Can (2.5 gal.) -71 33500 Fuel Stabilizer -71 33000 SAE 30W Oti (20 oz.) -. 71 33417 Dust Shield -71 33316 Mower Cover ROTARY G_ GO LAWN MOWER MODEL NUMBER 917.377520 ROTARY KEY NO. 1 2 3 4 cO 5 6 8 9 10 !I 12 t3 14 15 16 PART NO. 145755 48385 751152 158755 146527 150495 77400 145212 88446 151156 12000058 137054 88080 88118 67725 LAWN MOWER MODEL KEY NO. NUMBER PART NO. 917.377520 DESCRIPTION DESCRIPTION Contro! Cable Assembly Control Head Kit Locknut #10-24 Pan Head Machine Screw 1/4 x 2.12 V-Belt Spring Retainer Hubcap Flanged Nut Nylon Bushing Wheel & Tire Assembly E-Ring Pinion Dust Cover Felt Washer Washer 1/2 x t-112 x .134 18 25 26 701037 151522 143603 28 31 32 33 35 154990 132010 137052 48386 151521 36 37 40 41 702511 137090 75192 151520 53 54 144747 154862 55 57 86012 144748 Selector Knob Drive Cover Decal Pan Head Tapping Screw #10-24 x 2-3/4 Drive Cover Hex Flange Nut Drive Pulley Drive Control Cable Kit Wheel Adjuster Assembly (Left) Gear Case Assembly Spring Spring Wheel Adjuster Assembly (Right) Frame Throat Grassbag Assembly with tube Driveshaft Cover Frame Tube BRIGGS & STRATTON MODEL NO. 12H802 TYPE NO. 1978-E1 968 606 '_ 971A 843 967 621 529 92_P It 258 I 131 J % I 1 1 I f 124 634 ! I _o_ 130 ! 127 95 t_617 40 MODEL NO. 12H802 TYPE NO. 1978-E1 BRIGGS & STRATTON 4-CYCLE ENGINE 15 625 383 306 307 41 REQUIRES SPECIAL TOOLS TO INSTALL. SEE REPAIR INSTRUCTION MANUAL, BRIGGS & STRATTON MODEL NO. 12H802 TYPE NO. 1978-E1 9 _) 670A (_ 358 GASKET SET 3 i 524 0 _ 20 104 _) 634 ............ llll,i i i '134 617 ii ii llllll, ii, , _3 O 127 116 617 H 977 CARBURETOR GASKET SET I u 121 CARBURETOR 634 KIT 334 356 I ,_! '_ 202 "_ 209 42 670A MODEL NO. 12H802 TYPE NO. 1978-E1 BRIGGS & STRATTON .4:CYCLE ENGINE ........................... 972 930 304 55 , 1 L_J • . | 43 BRIGGS & STRAT'rON KEY NO. PART NO. 1 2 3 4 5 7 8 9 9A 10 11 12 13 15 16 493260 293708 299819 493279 214368 272916 495786 272481 272238 94650 231933 272198 94547 9_880 498565 94388 399781 94220 94612 20 22 23 24 25 492177 222698 499429 26 499425 27 28 263190 499423 29 32 33 34 35 40 45 46 499424 94699 26265'1 262652 262224 93312 262204 498275 MODEL NO. 12H802 TYPE NO. 1978-E1 DESCRIPTION m_t Cylinder Assembly Bushing, Cylinder ' Seal, Oil Sump, Engine Head, Cylinder Gasket, Cylinder Head Breather Assembly Gasket, Valve Cover i Gasket, Baffle Plate Screw, Hex Head Tube, Breather * Gasket, Crankcase Screw, Cylinder Head Plug, Oit Drain Crankshaft Timing Gear Key * Seal, Oil Screw, Hex Head Screw, Hex Head (Used in Hole Nearest Breather) Flywheel ' Key, Flywh'eel Piston Assembly, ' Standard Size Ring Set, Piston, Standard Size Lock, Piston Pin Pin, Piston, Standard Size Rod, Connecting Screw, Connecting Rod Valve, Exhaust Valve, intake Spring, Valve Retainer, Valve Spring Tappet, Valve Gear, Cam KEY NO. PART NO, 47 51 54 55 56 58 493737 272199 94526 497442 498144 280399 60 65 8t 95 104 110 281434 94696 223664 94098 231371 --- 117 121 124 494870 498260 94840 125 127 498170 ... 130 t31 133 134 224908 493267 398187 398188 137 - -- I63 187 188 188A 202 2O9 272653 298049 398540 94644 262579 263044 * *" *** DESCRIPTION Slinger, Oil * Gasket, Intake Elbow Screw, Hex Head Housing, Rewind Starter Pulley, Rewind Starter Rope, Rewind Starter (Cut To 88-5/8") Grip, Starter Rope Screw, Phillips Lock, Muffler Screw Screw, Round Head ** Pin, Float Hinge "'* Gasket, Sealing (Sold in Kit Only) Jet, Main Carburetor Kit Screw, Carburetor Mounting Carburetor 0, Plug, Welch (Sold in Kit Only) Valve, Throttle Shaft, Throttle Float, Carburetor Valve, Inlet (Includes Seat) "*" Gasket, Bowl (Sold in Kit Only) "Gasket, Air Cleaner Hose, Fuel Screw, Hex Head Screw, Hex Head Link, Governor Spring, Governor Included in Gasket Set (497316) Included in Carburetor Kit (498260) Included in both Carburetor Kit (498260), and Carburetor Gasket Set (498261) Included in both Gasket Set (497316), Set (497316) and Valve overnauf Gasket Set (498528).. NOTE: All component dimensionsgiven in U.S_inches 1 inch = 25.4 mm 44 BRIGGS & STRATTON .4_;.CYCLE ENGINE .......................................................................................... KEY NOo PART NO. 227 230 258 284 300 304 305 306 307 332 333 334 337 356 358 363 383 387 447 455 456 459 461 515 523 524 525 529 562 572 592 601 605 606 608 Incl: 492349 67072 94512 94511 497638 493293 94744 224324 94515 94877 802574 94731 802592 497833 497316 19069 89838 496115 95013 225121 281503 281505 94943 263073 495264 280393 495265 281299 94852 224328 231082 93053 225103 224815 497680 94904 94908 94231 94474 263175 270344 499635 396847 497465 613 615 616 617 620 62t 625 DESCRIPTION Lever, Governor Washer, Thrust Screw, Hex Head Screw, Hex Head Muffler, Exhaust Housing, Blower Screw, Sems Shield, Cylinder Screw, Hex Head Nut, Flywheel Armature, Magneto Screw, Seres Plug, Spark Wire, Ground Gasket Set Puller, Flywheel Wrench, Spark Plug Primer, Carburetor Screw, Hex Cup, Starter Retainer, Starter Pawl, Rachet Screw, Shoulder Spring, Retainer Cap, Oil Filler * Seal, FiIler Tube Tube, Oil Fill Grommet Bolt, Governor Lever Baffle, Cylinder Nut, Hex Clamp, Hose Cover, Control Strap, Bracket Starter, Rewind Screw, Hex Nut, Hex Screw, Hex Head Fastener Crank, Governor *'* Seal, intake Elbow Bracket, Carburetor Switch, Stop Tube, Fuel intake KEY NO. PART NO, 634 --- 635 670 670A 741 842 843 847 851 869 870 871 66538 280512 493823 262598 280966 272616 495263 493880 213512 213513 262001 63709 262640 493442 281145 281136 397974 496116 491568 281340 94872 94873 94749 495224 493640 498261 499341 498258 922 923 925 930 957 966 967 968 969 971 971A 972 975 977 I036 1095 2500 -- 12JB02-2915 498826 RPM Settings: * ** "* MODEL NO. 12H802 TYPE NO. 1978-E1 DESCRIPTION *'" Washer, Shaft (Sold in Kit Only) Elbow, Spark Plug Spacer, Fuel Tank * Spacer, Bracket Gear, Timing " Seal, O-Ring Sleeve, Lever Tube Assembly, Oil Terminal, Ignition Cable Seat, Intake Valve Seat, Exhaust Valve Guide, Exhaust Valve Guide, intake Valve Spring, Brake Brake Assembly Cover, Linkage Guard, Finger Cap, Fuel Tank Base, Air Cleaner Filter, Air Cover, Air Cleaner Screw, Hex Head Screw, Hex Head Screw, Hex Head Tank, Fuel Bowl, Float Gasket Set, Carburetor Label Kit, Emission Gasket Set, Valve Overhaul Replacement Engine Replacement Shortbiock Low: 1900-2100; _3000-3200 High: Included in Gasket Set (497316) Included in Carburetor Kit (498260) included in both Carburetor Kit (496260), and Carburetor Gasket Set (49826t) Included in both Gasket Set (497316), Set (497316) and Valve overhaul Gasket Set (498528). NOTE: 45 AI! component dimensions given tn UoS. inches 1 inch = 25.4 mm 46 47 For the repair or replacement parts you need delivered directly to your home Call 7 am - 7 pro, 7 days a week 1=800=366=PART (1-800-366-727B) Para ordenar piezas con entrega a domicUio - 1-800-659-7084 For in-house major brand repair service Call 24 hours a day, 7 days a week 1=800-4-REPAIR (1-800-473-7274) Para pedir servicio de reparaci6n domicilio - 1-800-676-5811 a For the location of a Sears Parts and Repair Center in your area Call 24 hours a day, 7 days a week 1=800-488-1222 For information on purchasing a Sears Maintenance Agreement or to inquire about an existing Agreement Call 9 am -5 pm, Monday-Saturday 1=800-827=6655 When requesting service or ordering parts, always provide the following information: oProduct Type oPart Number o Model Number • Part Description Amenca's 161767 04.29.98 REV.3 VB Repair Speciat_$_s Printed in U.S.A.
This document in other languages
- español: Craftsman 917.377520