Download - Wiedamark
Transcript
Illuminator User Guide Sirius Illuminator Range Models covered by this manual: UFOSIRCW | UFOSIRCW-C | UFOSIRCW-T UFOSIRSW | UFOSIRSW-C | UFOSIRSW-T UFOSIRNW | UFOSIRNW-C | UFOSIRNW-T UFOSIRWW | UFOSIRWW-C | UFOSIRWW-T UFOSIRGW | UFOSIRGW-C | UFOSIRGW-T Please read this manual fully before installing, operating or performing maintenance on the illuminator unit. Universal Fiber Optic Lighting LLC Issue 1 | Revised: 24062014 6119A Clark Center Avenue | Sarasota | FL34238 Tel: 941-343-8115 | Fax:941-296-7906 www.fiberopticlighting.com INTRODUCTION Thank you for purchasing this UFO Illuminator. Please read these instructions fully before connecting your unit to the electrical supply, and keep them for future reference. The UFO Sirius range of illuminators are suitable for use with either glass or PMMA fiber-optic harnesses. The Sirius is powered by a 100-240 VAC remote desktop power supply unit. IMPORTANT THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. 2 Sirius Illuminator Range MODEL TYPES The Sirius LED illuminator incorporates a range of LED arrays focussed through a series of static lenses to provide optimum display and illumination within the following optical range. Model Description CRI Color Temperature Lumen Output SIRCW Cool White 75 5700K 5700 SIRSW Studio White 88 5300K 4650 SIRNW Neutral White 82 4000K 5300 83 3000K 4650 Gallery White 98 3000K 3450 SIRWW Warm White SIRGW CONSTRUCTION DETAILS Model Description UFOSIRCW UFOSIRSW UFOSIRNW UFOSIRWW UFOSIRGW White light LED - cool white output - manual, DMX or 0-10V dimming UFOSIRCW-C UFOSIRSW-C UFOSIRNW-C UFOSIRWW-C UFOSIRGW-C UFOSIRCW-T UFOSIRSW-T UFOSIRNW-T UFOSIRWW-T UFOSIRGW-T White light LED - studio white output - manual, DMX or 0-10V dimming White light LED - neutral white output - manual, DMX or 0-10V dimming White light LED - warm white output - manual, DMX or 0-10V dimming White light LED - gallery white output - manual, DMX or 0-10V dimming White light LED with 6 segment decorative colorwheel- cool white output - manual, DMX or 0-10V dimming and wheel control White light LED with 6 segment decorative colorwheel- studio white output - manual, DMX or 0-10V dimming and wheel control White light LED with 6 segment decorative colorwheel- neutral white output - manual, DMX or 0-10V dimming and wheel control White light LED with 6 segment decorative colorwheel- warm white output - manual, DMX or 0-10V dimming and wheel control White light LED with 6 segment decorative colorwheel- gallery white output - manual, DMX or 0-10V dimming and wheel control White light LED with metal decorative twinkle wheel- cool white output - manual, DMX or 010V dimming and wheel control White light LED with metal decorative twinkle wheel - studio white output - manual, DMX or 0-10V dimming and wheel control White light LED with metal decorative twinkle wheel- neutral white output - manual, DMX or 0-10V dimming and wheel control White light LED with metal decorative twinkle wheel- warm white output - manual, DMX or 0-10V dimming and wheel control White light LED with metal decorative twinkle wheel- gallery white output - manual, DMX or 0-10V dimming and wheel control Universal Fiber Optics 3 POWER SUPPLY REQUIREMENTS The LED Illuminator is powered from a multifunction, multi-voltage, desk top Power Supply Unit. Remove the 24V Desk Top PSU from its box. This PSU is an IEC input device catering for UK, European and USA mains supplies using the relevant power cord. The SIRIUS LED illuminator must be powered by the supplied 24V 3.75A Desk Top LPS/Class 2 power supply. GENERAL The SIRIUS is a 90W White Light LED Illuminator with optional decorative wheel capability. The SIRIUS LED Illuminator driver PCB has all the control functionality fitted as standard. The following control functionality is available (see following image) 1. Manual dimming 2. Manual Decorative Wheel control (various wheel speeds and stop/start) 3. DMX dimming 4. DMX Decorative Wheel control 5. 0-10V Decorative Wheel control – channel 1 (receiving) 6. 0-10V dimming – channel 2 (receiving) 4 Sirius Illuminator Range DIP Switch 10 ON (down) for manual or 0-10V o DIP Switch 10 OFF (up) for DMX operation DMX ADDRESS AND MANUAL DIP SWITCH MANUAL MOTOR CONTROL MANUAL DIMMING 24V DC INPUT 0-10V MOTOR CONTROL 0-10V DIMMING DMX CONNECTION – MANUAL OPERATION There are 2 connections required – the fiber port and the mains supply cable. The fiber port should be connected first. Connect and secure the fiber optic connector into the green collar and secure using the M5 locking screw. Connect the IEC power cord into the Desk Top PSU and plug the mains plug into the electrical supply socket. Switch on power the led Indicator will illuminate and the illuminator is ready for use. If no light is produced consult the TROUBLESHOOTING section. NOTE: THESE ILLUMINATORS ARE NOT MAINS DIMMABLE MANUAL OPERATION - WHITE LIGHT DIMMING For normal manual operation DIP switch 10 must be ON. During normal manual white light operation the illuminator can be dimmed from 0 to 100% using the Manual Dimming Control on the side panel. Universal Fiber Optics 5 MANUAL OPERATION - DECORATIVE WHEEL CONTROL For normal manual operation DIP switch 10 must be ON. During normal manual decorative operation the illuminator can be dimmed from 0 to 100% using the Manual Dimming Control and the motor can be controlled from stop to 4 speeds (slow to fast) using the push button Manual Motor Control on the side panel. CONNECTION – 0-10V OPERATION There are 3 connections required – the fiber port, the mains supply cable and the 0-10V cable. The fiber port should be connected first. Connect and secure the fiber optic connector into the aluminium collar and secure using the M5 locking screw. Connect the IEC power cord into the Desk Top PSU and plug the mains plug into the electrical supply socket. Switch on power the led indicator will illuminate and the illuminator is ready for use. In no light is produced consult the TROUBLESHOOTING section. Connect the 0-10V RJ45 as detailed below using CAT5 cable 0-10V RJ45 Connections: -VE RJ45 Brown/White (Pin 7) +VE RJ45 Blue/White (Pin 5) 6 Sirius Illuminator Range 0-10V OPERATION - WHITE LIGHT DIMMING For 0-10v dimming operation DIP switch 10 must be ON, the Manual Dimming Control on the side panel must be turned to minimum (fully counter clockwise), and the RJ45 plug must be plugged into the right hand RJ45 socket on the side panel. The illuminator can be dimmed from 0 (0 Volts DC) to 100% (10V DC) with a receiving 0-10V signal. 0-10V OPERATION - DECORATIVE WHEEL CONTROL For 0-10v wheel control DIP switch 10 must be ON, and the RJ45 plug must be plugged into the left hand RJ45 socket on the side panel. The illuminator decorative wheel can be controlled with a receiving 0-10V signal as detailed in the following 0-10V value table. Function Value Description Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel 0V 0.4V 0.8V 1.2V 1.6V 2V 2.3V 2.6V 3V 3.6V 4V 4.4V 4.6V 5.4V to 9.2V 9.3V to 10V White (Color 1) Yellow (Color 2) Green (Color 3) Orange (Color 4) Magenta (Color 5) Blue (Color 6) Returns to White (Color 1) Blue (Color 6) Magenta (Color 5) Orange (Color 4) Green (Color 3) Yellow (Color 2) White (Color 1) Slow to fast clockwise* Fast counter clockwise* NOTE: For Twinkle wheel control use values marked* Universal Fiber Optics 7 CONNECTION – DMX OPERATION There are 3 connections required – the fiber port, the mains supply cable and the 0-10V cable. The fiber port should be connected first. Connect and secure the fiber optic connector into the aluminium collar and secure using the M5 locking screw. Connect the IEC power cord into the Desk Top PSU and plug the mains plug into the electrical supply socket. Switch on power the led indicator will illuminate and the illuminator is ready for use. In no light is produced consult the TROUBLESHOOTING section. Connect the 3 pin XLR sockets on the side panel as detailed below using an approved DMX cable. NOTE: It is recommended that a 120ohm terminating resistor be connected across DMX+ and DMX- on the last illuminator in the DMX universe or cable run 8 Sirius Illuminator Range SETTING THE DMX ADDRESS The DMX address of each illuminator is set manually using the DIP switch accessible on the side panel as shown below. DMX B Start Ch# DIPDMX B Switches Start on Ch# DIP Switches on 1 1 11 1,2,4 2 2 12 3,4 3 1,2 13 1,3,4 4 3 14 2,3,4 5 1,3 15 1,2,3,4 6 2,3 16 5 7 1,2,3 : 8 4 : 9 1,4 : 10 2,4 511 Above Example 1 - On 2 - Off 3 - Off 4 - On 5 - Off 6 - On 7 - On 8 - Off 9 - Off 10 - Off = Address 105 1,2,3,4,5 ,6,7,8,9 DMX OPERATION - WHITE LIGHT DIMMING For DMX dimming operation DIP switch 10 must be OFF and the XLR plug(s) must be plugged into the XLR sockets on the side panel. The illuminator can be dimmed on DMX channel 1 as shown in the DMX table overleaf. DMX OPERATION - DECORATIVE WHEEL CONTROL For DMX wheel control DIP switch 10 must be OFF and the XLR plug(s) must be plugged into the XLR sockets on the side panel The illuminator decorative wheel can be controlled on DMX channel 2 as shown in the DMX table overleaf. Universal Fiber Optics 9 DMX OPERATION - LED/FAN CONTROL For DMX LED and fan control, switch 10 must be OFF and the XLR plug(s) must be plugged into the XLR sockets on the side panel The illuminator LED and Fan can be controlled on DMX channel 3 as shown in the following DMX table. Channel Function Value Description 1 Dimming 0-255 From OFF at 0 to Brightest at 255 2 Color Wheel 0-9 White - Snap to color (Color 1) 2 Color Wheel 10 Yellow - Snap to color (Color 2) 2 Color Wheel 20 Green - Snap to color (Color 3) 2 Color Wheel 30 Orange - Snap to color (Color 4) 2 Color Wheel 40 Magenta - Snap to color (Color 5) 2 Color Wheel 50 - 70 Blue - Snap to color (Color 6) 2 Color Wheel 80 Magenta - Snap to color (Color 5) 2 Color Wheel 90 Orange - Snap to color (Color 4) 2 Color Wheel 100 Green - Snap to color (Color 3) 2 Color Wheel 110 Yellow - snap to color (Color 2) 2 Color Wheel 120 White - Snap to color (Color 1) 2 Color Wheel 128-189 Slow to fast rotation clockwise 2 Color Wheel 189-255 Fast to slow rotation counter clockwise 3 LED & Fan 0-250 LED and fan ON 3 LED & Fan 251-255 LED and fan OFF 10 Sirius Illuminator Range DECORATIVE WHEELS The following decorative wheels are available. Color Wheel The standard decorative color wheel has 6 glass segments as follows:White (Clear), Yellow, Green, Orange, Magenta, Blue Alternatively, a 6 segment or 4 segment vari-color wheel can be fitted providing the following color segment options:FIRE Orange Golden Amber Y89 G78 G96 O08 Canary Italian Blue C45 Violet V43 O18 Green Brilliant Blue B06 Magenta M56 O59 Jade Apricot O14 Turquoise C47 Bright Blue Congo M63 Clear - Outputs white light B28 Pink B93 Twinkle Wheel Two variations are available. Firstly an un-segmented wheel designed to rotate continuously in one direction only. Secondly a segmented wheel that with correct DMX controller programming can rotate clock wise and counter clockwise in sequence with an open segment being the full light default position. Universal Fiber Optics 11 MAINTENANCE Please Note that a record of all maintenance MUST be kept in the table below, indicating what maintenance was undertaken and when. This MUST be dated for warranty purposes. Date 12 Sirius Illuminator Range Maintenance Undertaken TROUBLESHOOTING Problem Possible causes Mains supply off Unit is dead - no Loose mains plug light output and PSU power indicator Plug blown fuse (UK) is out PSU failed Dimming control at minimum Unit is dead - no light output but PSU DIP switch no. 10 not switched ON power indicator is lit [1] LED array or drive failure Remedy Check supply and reinstate Check plugs Check fuse & replace if necessary Replace PSU Adjust brightness on dimmer control Switch DIP switch 10 ON Replace illuminator Motor control at minimum Adjust motor control DIP switch no. 10 not switched ON Switch DIP switch 10 ON Driver circuit or motor failure Replace illuminator DIP switch no. 10 is switched ON Switch DIP switch no. 10 OFF DMX address not correctly set Set correct DMX address No DMX signal from controller Check DMX controller settings Wiring fault on DMX cables Check cables and repair/replace Driver circuit failure Replace illuminator DIP switch no. 10 not switched ON Switch DIP switch 10 ON Not responding [4] No 0-10V signal at illuminator due to cable or controller fault Check input to illuminator using a DMM set to correct range & rectify cable/controller fault Responding on wrong channels [4] RJ45 connector in wrong socket on illuminator Plug into correct socket Not responding [5] Manual dimming control not set to Turn manual dimmer control fully counter clockwise minimum Not responding [6] If none of above, driver circuit failure Replace illuminator Illuminator dimmed manually or by 0-10V or DMX control Check and increase dimmer settings LED driver / array failure Replace illuminator Decorative wheel is not turning [2] Unit is not responding to DMX control [3] Poor light output on fiber [1] - white light manual dimming version [2] - decorative manual motor version [3] - for DMX only [4] - decorative or dimming 0-10V control [5] - dimming 0-10V control [6] - 0-10V control Universal Fiber Optics 13 TECHNICAL SPECIFICATIONS Description Details Port connector size 30mm Diameter Fiber type Glass/PMMA Mains supply voltage 100-240V AC, 47-63 Hz. 0.58A PSU output 24V DC, 3.75A, 90W Maximum LED type LED engine LZP 24 die emitter LED power 90W Mains running current 400mA Max. VA rating 96VA Motor type Rotalink 25C13/YS0LPSL3E 12V 60:1 Power cord Standard IEC PSU type LPS or class 2 LED type/model White light with optional effect wheel LED life 40,000 hours Cool white LED array 5500K, 75CRI, 5700lm Studio white LED array 5300K, 88CRI, 4650lm Neutral white LED array 4000K, 82CRI, 5300lm Warm white LED array 3000K, 83CRI, 4650lm Gallery white LED array 3000K, 98CRI, 3450lm DMX User addressable (0-255) dimming, effects wheel control and on/off Control functionality Manual, 0-10V dimming, DMX Operating environment Indoor / dry Min. ambient temperature -10°C Max. ambient temperature 30°C Material Aluminium Color Grey Size (white light) W278mm x H93mm x D152mm Size (decorative) W278mm x H127mm x D152mm 14 Sirius Illuminator Range NOTES Universal Fiber Optics 15 Universal Fiber Optic Lighting LLC 6119A Clark Center Avenue | Sarasota | FL34238 Tel: 941-343-8115 | Fax:941-296-7906 www.fiberopticlighting.com