Download Aaton Cantar-X2

Transcript
Description 4,
p.7
Circular screens
These are the largest, easiest-to-read screens found on any
audio recorder. They provide the user with ongoing data
concerning every aspect of the machine's operation while it
•• Output maps
is operating. It takes a few hours getting used to them since
Here is where Cantar's three screen ’mapping’ is at its best.
five display paradigms are used for the many functions they
Audio signals going to the left ear show on the left screen,
handle. Once you are familiar with these functions, you will
signals to be listened to in mono show on the middle screen
drive the fastest machine you have ever driven.
and those going to the right ear are on the right screen.
• input grids. The six primary tracks graphically display
All inputs (recorded or not, very useful in Rec&Play), and all
their links at the push of a button, even while recording.
tracks can be monitored along different configurations for
•• output maps. Thanks to the three screen lay-out emu-
each of the eight independent outputs channels: Ph Phones,
lating the left, both and right ‘ears’, the monitor maps are
Lo Line-out, Fb Foldback and Do Digital-out. 26 different
immediately understood.
‘output routing’ maps are available; the black [monitor]
••• progressive pan-pots. The contribution of each track
crown gives instant access to all of them, see p.28.
to the mixdown has never been so clear.
•••• circular modulometers. Their round shape makes the
signal level easy to appreciate in a wink.
••••• monitoring physical status. Permanent control of
the disks, tracks, and setups.
• Input grids
In the example above, the ‘Ph d’ phone routing indicates:
The available ‘Inputs’ are shown in each circular screen:
Track 5 goes to the left ear, Track 1 and Track 2 go to the
Line-in 1 to Line-in 4, Mic 1 to Mic 5, Digi 1 to Digi 6.
center (both ears) and Track 6 goes to the right ear.
The
With
six tracks to which they can be connected are grouped in
the [Solo Mix Pan] slider pulled toward the operator side,
pairs, e.g. T1 T2, T3 T4, T5 T6 on the three screens.
pressure on the [routing] button instantly displays the current
The method of creating routing-configurations by linking in-
monitor configuration.
puts and tracks is explained in the section ‘Routing inputs to
Note: the [routing] button is required to change from one
tracks’, p.26.
grid to another, it is a protection against wild and lethal
changes, but it is not required to change from one map to
another in the course of a recording.
••• Pan-pots to the mixdown
Push the [Solo Mix Pan] slider toward the battery side, press
the [track-solo] button next to the mixer linear fader: the panWith the [Solo Mix Pan] slider pushed toward the battery,
pot of this track goes under [jog] control and indicates its
the [routing] button (top-left of the swiveling panel) instantly
left/right contribution to either channel of the mixdown.
displays the ‘inputs to tracks’ grid, even while recording.
In the picture above the middle screen displays ‘A4’, the
routing in use. Fifteen preset routing grids are stored in three
banks. Each of which holds five grids, to help you sort and
memorize your configurations, e.g. A1 to A5 for mic only
setups, B1to B5 when some line-inputs are on duty, C1to
C5 for complex setups that include digi-inputs. The [config]
crown gives instant sequential access to all of them.
T1 & T2 left
T3 center, T4 left
T5 left, T6 right
The spatial position of all pan-pots is visible on the circular
screens while the dBFS value of the selected pan-pot is displayed in the rectangular screen (see next page).
+33 4 7642 9550
www.aaton.com
User manual for Cantar-X1 & X2, v2.11 2008 Feb. 25
p.7