Download User Manual

9078 plus
9078D plus
User Manual
Compuprint Information
Thanks for choosing this printer.
Your printer is a reliable working equipment that will be very useful in your
daily job.
Our printer have been designed to be compact and respectful of the work
environment. They offer a wide range of features and multiple functions that
confirm the high technological level reached by the Compuprint S.p.A .
To maintain these printing performances unchanged in the long run,
Compuprint has developed specific consumable accessories for each printer
type (for example: ribbon cartridges for dot matrix printers, toner and OPC
cartridges for laser printers, bubble ink jet cartridges for inkjet printers) that
assure an excellent operation with high printing quality level reliability.
Compuprint recommends to use only its original consumables with
original packaging (identified by its holographic label). In this way, a
proper use of the printer at quality level unreliability stated in the product
characteristics can be assured. All typical usage problems related to not
certificated consumables may be avoided, such as an overall quality print
level degradation and ,often, the reduction of the product life due to the fact
that the proper print heads working conditions, OPC cartridge and other
printer parts are not assured.
Moreover, Compuprint does not only certify its consumables in terms of
working conditions but also carefully controls their compliance with the
international standard rules concerning:
•
no cancerous materials;
•
no inflammability of the plastic materials;
•
other standards
Compuprint advices the customers not to use products for which the
compliance to this safety rules are not warranted.
Finally seek your dealer or contact a Compuprint office and be sure that are
provided you the original Compuprint consumables.
A78408739-002
i
FCC Notes
FCC Notes
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occurin a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver to
outlets on different circuits.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could avoid the user's authority to operate the equipment. The
use of a non-shielded interface cable with the referenced device is prohibited.
The length of the parallel interface cable must be 3 meters (10 feet) or less.
The length of the serial interface cable must be 15 meters (50 feet) or less..
Canadian D.O.C. Radio Interference Regulation
This digital apparatus does not exceed the Class B limits for radio noise
emission from digital apparatus as set out in the radio interference
regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de classe A
prescrites dans le règlement sur le brouillage radioélectrique édicté par le
ministère des communications du Canada.
EEC Regulations
This equipment conforms to the EEC Directive 89/392 (the sound pressure,
measured according to ISO 7779, does not exceed 70 dBA).
ii
A78408739-002
Safety Information
Safety Information
A. Never remove any printer cover unless it is necessary for the installation of a
printer accessory and expressly described in this manual.
B. Please retain the printer covers in a safe place because they should be
reinstalled if you decide to remove any printer accessory.
The following areas of the printer should be covered for safety
reasons:
R e ar Tractor C o ve r
Pa pe r Stacker O p enin gs
ASF In stalla tio n Are a
C o ve rs
The above openings must always be protected with
their cover when the corresponding option is not
installed. Do not touch inside and do not insert any
object into these openings or into the gears.
A78408739-002
iii
Table of Contents
Table of Contents
Compuprint Information ..........................................................................ii
FCC Notes ................................................................................................iii
Canadian D.O.C. Radio Interference Regulation.......................................... ii
EEC Regulations ............................................................................................ ii
Safety Information..................................................................................iiii
Table of Contents...................................................................................iiv
Getting to Know Your Printer ................................................................1
1
Printer Features ............................................................................................. 1
Unpacking Your Printer................................................................................. 1
Printer Parts................................................................................................... 2
Front View .................................................................................................. 2
Rear View.................................................................................................... 3
Setting Up Your Printer ..........................................................................4
4
Choosing a Suitable Location ........................................................................ 4
Printer Assembly............................................................................................ 5
Removal of the Shipment Locks ................................................................ 5
Ribbon Cartridge Installation.................................................................... 5
Upper Push Tractor Installation (9078D plus model only) ...................... 9
Host Computer Connection.......................................................................... 10
Software Driver Selection ............................................................................ 11
Power Connection......................................................................................... 11
Selecting the Display Language ..........................................................1
13
Configuring the Printer .........................................................................1
14
Operator Panel Presentation ....................................................................... 14
Display Messages ..................................................................................... 14
Status Messages ....................................................................................... 15
Indicators .................................................................................................. 16
Function Keys........................................................................................... 16
Key Combination ...................................................................................... 19
Printer Setups .............................................................................................. 20
Entering the Printer Setups .................................................................... 20
Moving within the Printer Setups ........................................................... 20
Leaving the Printer Setups...................................................................... 20
Power-On Configuration .............................................................................. 21
Entering the Power-On Configuration .................................................... 21
Program Setup.............................................................................................. 35
Entering the Program Setup.................................................................... 35
How to Select the Paper Path ...................................................................... 46
iv
A78408739-002
Table of Contents
How to Use the Tear-Off Function .............................................................. 47
Selection of the Paper Size....................................................................... 47
Adjusting the Tear-Off Position............................................................... 48
Selection of the Tear-Off Mode ................................................................ 48
How to Lock/Unlock the Access to the Printer Setups ............................... 50
How to Handle the Paper Parking............................................................... 51
Paper Handling ......................................................................................5
52
Paper Paths .................................................................................................. 52
Paper Specifications ..................................................................................... 52
Fanfold Paper (9078 plus and 9078D plus models) ................................ 53
Envelopes (9078 plus model only) ........................................................... 53
Cut Sheets (9078 plus model only) .......................................................... 53
Cut Sheets..................................................................................................... 54
Cut Sheet Loading Modes ........................................................................ 54
Loading Cut Sheets .................................................................................. 54
Fanfold Paper ............................................................................................... 56
Loading Paper Using the Lower Tractor................................................. 56
Loading Paper Using the Upper Tractor................................................. 61
Loading Paper Using the Lower Push Tractor and the Rear Pull Tractor
(option) ...................................................................................................... 64
Printer Maintenance and Troubleshooting.........................................6
66
Cleaning the Printer .................................................................................... 66
Replacing the Ribbon Cartridge .................................................................. 66
Printing the Self Test ................................................................................... 67
Error Handling ............................................................................................. 67
Options...................................................................................................7
70
The Rear Pull Tractor .................................................................................. 70
Installing the Rear Pull Tractor .............................................................. 70
Removing the Rear Pull Tractor.............................................................. 71
Automatic Sheet Feeder............................................................................... 72
Color Kit........................................................................................................ 73
Pedestals ....................................................................................................... 73
The Cutter..................................................................................................... 74
Installing the Cutter ................................................................................ 74
Printer Specifications ...........................................................................7
77
A78408739-002
v
Table of Contents
vi
A78408739-002
Getting to Know Your Printer
Printer Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
24 Needle Print Head
136 columns
Draft print at 700 cps, LQ print at 133 /200 cps and NLQ print at 266/400 cps
IBM Proprinter XL24-XL24E, IBM Personal Printer 2391 and EPSON LQ
1050-2550 emulations
High Resolution Graphics Printing (360 x 360 dots per inch)
Multiple copies (1 original and 7 copies)
Automatic paper path selection
Easy operability via operator panel menu and S/W commands
Optional Automatic Sheet Feeder (120 sheets capability) which handles
cut sheets, multicopies and envelopes, accepts up to two additional paper
bins and includes paper stacker
Optional Color Kit
Optional Cutter
Usage of all specific features by means of the Specific Software Driver
which is applicable to the most popular S/W Packages
Bar Code print with two densities choice
Plug & Play capability for Windows 95/98
Bi-directional IEEE 1284 parallel interface and standard serial RS-232/C
and RS-422/A interface
Unpacking Your Printer
Together with the user manual, the following items are included in the box:
Notify any damage to your supplier.
C D-R O M
U pp er P u sh Tractor
(907 8D plus m ode l o nly)
R ib bon Cartridg e
P ow e r Ca ble
A78408739-002
1
Getting to Know Your Printer
Printer Parts
Front View
9078 plus model
O pera tor P a ne l
P a pe r K n ob
C u t S h ee t S upport
P o w er S w itch
P u sh Tra c tor C ove r
P a pe r G u id es
9078D plus model
O perator Panel
Paper Knob
Push Tractors Cover
Pow er S witch
2
A78408739-002
Getting to Know Your Printer
Rear View
R ear P aper Slo t
Top C over
R ear Tractor A rea
C over
P a per K no b
Interfa ce C onnectors
A S F Are a C over
P ow er C ab le C o nnector
A78408739-002
R ear Tractor Installation
A re a C ove rs
3
Setting Up Your Printer
Setting Up Your Printer
Choosing a Suitable Location
Consider the following points when you choose the location for your printer:
•
The distance between the printer and the host computer must not exceed
the length of the interface cable;
•
The location must be sturdy, horizontal and stable;
•
Your printer must not be exposed to direct sunlight, extreme heat, cold,
dust or humidity (see later "Printer Specifications" section );
•
You need an AC power outlet compatible with the plug of the printer's
power cord. The voltage of the outlet must match the voltage shown on
the printer's Rating Plate;
Additionally, you must make sure that when you install the printer in the
selected location, there are sufficient clearances on all sides for easy
operation. The required space is shown below:
80 cm
3 1 .5 in .
1
39 00
.4 cm
in
m
20 c
in
7 .9
4
cm
0 in
10 .4
39
m
20 c
7 . 9 in
A78408739-002
Setting Up Your Printer
Printer Assembly
Removal of the Shipment Locks
Open all the printer covers and make sure that you remove all the shipment
locks from the printer.
Ribbon Cartridge Installation
Two types of ribbon cartridges are available for this printer, depending on
whether the color kit is installed or not.
1. Make sure that the printer is turned off.
2. Find the ribbon cartridge among the accessories.
R ib b on gu id e
Ten sion K n ob
C a rtrid g e P in
A78408739-002
5
Setting Up Your Printer
3. Open the top cover using the small handles on either side of the top cover.
4. Turn the printer on. The print carriage prepares for ribbon cartridge
installation.
5. Before installing the ribbon
cartridge turn the ribbon
winding knob in the arrow
direction (located on the
cartridge) to take up slack
in the ribbon.
6
R ib b on Ten sion
K n ob
To avoid damage to the ribbon, do not turn the winding knob in the wrong
direction.
A78408739-002
Setting Up Your Printer
6. Align the cartridge pins with the locking grooves on the left and right
cartridge supports.
The cartridge (black or color) to be used when the color kit is installed has only
one groove.
7. Slide and insert the ribbon guide between the print head and the ribbon
guide mask holding it perpendicular to the print head.
Make sure that the ribbon is inserted correctly between the print head and the
print head mask.
2.
A78408739-002
12
7
Setting Up Your Printer
If the color kit option is installed on your printer insert the white plastic
holder onto the color kit as shown in the following figure.
R ib b on G uide
H o ld er for C olor K it
C o lo r K it
8. Turn the ribbon winding
knob in the arrow direction
(located on the cartridge) to
take up slack in the ribbon.
R ib b on Ten sion
K n ob
9. Push the cartridge down gently until it clips into place at all four locking
points.
8
A78408739-002
Setting Up Your Printer
10. Turn the ribbon winding knob again in the direction of the arrow to take
up slack in the ribbon.
11. To ensure that the ribbon guide runs freely along the ribbon, manually
move the print carriage horizontally.
If you need to replace the used ribbon cartridge, see "Replacing the Ribbon
Cartridge" section later in this manual.
Upper Push Tractor Installation (9078D plus model only)
An additional push tractor is provided with the 9078D plus printer. This
second push tractor unit can be installed in front position (on the lower push
tractor).
1.
Find the upper
tractor
among
accessories.
push
the
2. Install the upper push tractor aligning both its hooks with the lower push
tractor pins and inserting them into the corresponding pins. Push the
upper tractor until it is fully engaged. Insert the connector cable in the
electrical connector located in the lower push tractor.
L ow e r Tractor P in
U ppe r Tractor H ook
E lectrical C on nector
C onn ector Ca ble
A78408739-002
9
Setting Up Your Printer
3. The upper push tractor must be installed as shown in figure.
4. If you need to remove the upper push tractor, turn the printer off. Take
the connector cable off and press on the internal levers (located in the
upper push tractor hooks) to disengage the tractor.
Host Computer Connection
This printer can be connected to your host computer via two available
interfaces. The interface connectors are located on the rear of the printer.
•
•
A bidirectional IEEE1284 parallel interface
A RS-232C/422C serial interface
Before connecting the interface cable, make sure that the printer and the host
computer are turned OFF .
Insert the parallel interface cable into the parallel connector and fasten it by
means of the clips.
Insert the serial interface cable into the serial connector, and fasten it by
means of the two screws (use the screwdriver).
10
A78408739-002
Setting Up Your Printer
Parallel interface
Serial interface
Software Driver Selection
At this point it is necessary to configure your printer for your application
package. The installation procedures depend upon the host environment.
Follow the instructions in the readme file you find on the CD-ROM..
In a WINDOWS 95/98 environment the printer supports the Plug & Play
feature.
The printer drivers of all Compuprint printers can be found at the Internet
Address http://www.compuprint.net
Power Connection
Make sure that the power outlet matches the power rating of the printer.
See the name plate of the printer, that you find under the rear ASF cover.
In case the power rating does not correspond DO NOT CONNECT THE
PRINTER TO THE MAINS. Consult your dealer for help.
A78408739-002
11
Setting Up Your Printer
1. Make sure the power outlet is near the printer location and easily
accessible.
Always use a grounded outlet.
2. Make sure that the power switch
is in 0 position (OFF).
3. Insert the power cable plug into the printer connector and the other
power cable end into a convenient outlet (the figure shows the European
version).
1
2
4. If you need to turn the printer on,
press the power switch in the
I position (ON).
12
A78408739-002
Selecting the Display Language
Selecting the Display Language
The display messages for this printer can be displayed in five different
languages: English (Default), French, German, Italian and Spanish. To
select the language, that you prefer, proceed as follows:
1.
Press the PROGRAM key and keep it pressed while powering on the printer
until the following message will be displayed:
2.
When you release the PROGRAM key, the following messages will be
RELEASE KEY
displayed:
9078 plus
or
9078D plus
then,
PRINT OUT? NO
3. Press the ↓ key to enter the menu. The first menu item is displayed:
PARALL INTERFACE
4. Press the ↓ key until the language first level function is displayed:
FUNCTIONS
5. Press the → key to pass to the second level functions:
PAPER OVERLAY
(9078 plus model)
or
SEQUENCE NONE
(9078D plus model)
6. Press the ↓ key until the menu language is displayed:
MENU ENGLISH
7. Press the → key to scroll the menu languages. When the desired
language is displayed, press the PROGRAM key to select it. The printer
exits the menu. From now on the display messages appear in the selected
language.
A78408739-002
13
Configuring the Printer
Configuring the Printer
Operator Panel Presentation
The operator panel enables you to perform many of the printer functions
including paper path selections, font selection and the printer setup.
R EA D Y
QUIET
L OA D /FF
↓
M IC R O F E ED
LF
M A CR O
PAT H
FO N T
PAR K
↑
PROGRAM
O N L IN E
PROGRAM
P ITC H
S H IFT
S H IFT
The operator panel consists of:
•
•
•
A 16 character display (Liquid Crystal Display)
Three function mode indicators
Seven function keys
Display Messages
Instruction Messages
Message
LOAD ASF1
LOAD ASF2
LOAD ASF3
LOAD LOWER PUSH
LOAD LOW.PUSH&MF
LOAD MANUAL FORM
LOAD PSH-PLL&MF
LOAD PUSH-PULL
LOAD UPPER PUSH
RELEASE KEY
Description
These
messages
are
displayed
when
corresponding paper path is out of paper.
the
The printer displays only the messages related to
the installed devices.
This message is displayed when you can release the
PROGRAM key in the Self-test selection or in the
Power-on Configuration procedure.
User Intervention Messages
Message
CHECK CUTTER
NUM. LINES < 12
EJECT PAPER
EJECT: SURE?
14
Description
The cutter option is not able to cut the paper properly,
because the paper length is less than 12 lines.
The printer is ejecting a cut sheet.
The user must confirm the ejection of the paper.
A78408739-002
Configuring the Printer
Message
MACRO
CHANGING
PARK ABORTED
PARK: SURE?
PATH CHANGING
TEAR OFF
PAPER
PARK PAPER
Description
The macro has been changed and the printer is updating
the settings.
This message appears to indicate that the interruption of the
paper parking, at the request of the user, has been set pressing
the SHIFT key.
The user must confirm the parking of the paper pressing
the PARK key or may abandon the park procedure
pressing the SHIFT key.
The path has been changed and the printer is updating
the settings.
These messages are displayed when the printer receives
a paper parking command. Tear off the fanfold then
press the PARK key to park the paper.
Status Messages
Message
font cpi
ASF1
Description
The printer is offline or online without printing.
The first paper bin of the automatic sheet feeder (ASF)
is selected.
ASF2
The second paper bin of the automatic sheet feeder
(ASF) is selected.
ASF3
The third paper bin of the automatic sheet feeder (ASF)
is selected.
LOWER PUSH
The lower push paper path is selected.
LOW.PUSH&MF
The lower push paper path and manual single sheet
path are selected (9078 plus model only).
MANUAL FORM
The manual single sheet path is selected
(9078 plus model only).
MENU LOCKED
When the access to the Printer Setups has been locked
at the power on, the printer displays this message.
MENU UNLOCKED
When the access to the Printer Setups has been
unlocked at the power on, the printer displays this
message.
MICRO FEED DOWN The paper is fed in microsteps downwards when
pressing the arrow key.
↓
MICRO FEED UP ↑ The paper is fed in microsteps upwards when pressing
the arrow key.
PSH-PLL&MF
The push-pull paper path and manual single sheet path
are selected (9078 plus model only).
PUSH-PULL
The push-pull paper path is selected.
A78408739-002
15
Configuring the Printer
Message
Description
QUIET PRINT OFF Printing at normal noise level.
QUIET PRINT ON Printing at reduced noise level
UPPER PUSH
The
upper
push
paper
path
is
selected
(9078D plus model only).
SELF TEST
Printing the self-test page.
SHIFT FUNCTION This message appears to indicate that the Shift
functions of the operator panel keys have been selected
pressing the SHIFT key.
Indicators
READY
PROGRAM
SH IFT
Lit when the printer can receive and print data (printer online).
Blinks when there is data in the buffer and the printer is offline.
Unlit, when the printer is disabled and the buffer does not
contain any data, or during the initialization, setup or tests.
Blinks when one of the printer setup procedures has been
selected: Program Configuration or Power-On Configuration.
Lit when the alternate function of the keys has been enabled
pressing the SHIFT key.
Function Keys
The function keys are enabled, when the printer is offline. (READY indicator
unlit). The function keys have three functions each.
The normal function of the keys does not require previous
Normal
action to select it. This function is indicated in black
Function
characters beside the function keys.
Shift
Function
The alternate function is selected pressing the SHIFT key.
The alternate functions of the keys are described on the gray
areas beside the keys. The SHIFT indicator lights and the
display shows the SHIFT FUNCTION message.
This function is not enabled, if the printer is in setup mode.
Program
Function
The program function is selected pressing the PROGRAM key,
where:
• If you press the key while powering on the printer, the
Power-On Configuration is selected..
• Pressing the key when the printer is enabled without
printing or disabled (READY indicator unlit), the Program
Setup is selected.
In the Program Setup mode only the four arrow keys and
the PROGRAM keys are enabled.
When the printer is in setup mode, the PROGRAM indicator
blinks.
16
A78408739-002
Configuring the Printer
ON LINE Key
ON LINE
Normal
Function
•
•
•
•
Program
Function
Enables or disables the printer.
If this key is pressed while powering the printer
on, the self test is printed; the printout is topped
pressing this key again.
In an error condition, once the error cause has
been removed, press this key to enable the
printer.
If the Tear-Off Function in the Program Setup is
set to Manual, press this key to position the
paper for the Tear-Off.
Pressing this key, the input buffer is cleared an a
break (250 msec.) on a serial interface is sent. The
message RESET & BREAK is displayed.
PROGRAM Key
PROGRAM Normal
Function
PITCH
Shift
Function
Program
Function
Enables the printer setups as follows:
• Pressing this key while powering on the printer, the
Power-On Configuration is selected.
• Pressing this key when the printer is enabled
without printing or disabled, (READY indicator
unlit) the Program Setup is enabled.
Selects the pitch to be used with the currently
selected font. The selected pitch is valid until the
printer is turned off.
Exits the current printer setup. See also “Leaving the
Printer Setups”, later in this section.
SHIFT Key
SHIFT
Normal
Function
Shift
Function
A78408739-002
Enables the alternative key functions.
If the printer is receiving print data, press the ON LINE
key before pressing the SHIFT key.
If no printing data are in the print buffer, pressing the
SHIFT key, the printer goes offline.
The display then shows SHIFT FUNCTION to indicate
that the Shift Function of the keys is enabled.
May be used to abort paper parking procedure. See
also “How to Handle the Paper Parking”, later in
this manual.
Disables the alternative key functions.
17
Configuring the Printer
LOAD/FF Key
LOAD/FF
Normal
Function
↑
Shift
Function
↑
Program
Function
Executes a Form Feed (FF): when paper is loaded
into the printer, it advances to the following page,
if no paper is loaded, it is positioned for printing.
Moves the paper forward in microsteps. Keeping
the key pressed the paper is moved continuously at
increasing speed.
Scrolls the parameters of the functions or macros
backwards
LF Key
LF
↓
↓
Normal
Function
Shift
Function
Program
Function
Performs a line feed according to the current line
spacing settings.
Moves the paper backward in microsteps. Keeping
the key pressed the paper is moved continuously at
increasing speed.
Scrolls the menu and macro functions forward.
MACRO Key
MACRO
PATH
←
Normal
Function
Shift
Function
Program
Function
Selects one of the user macros (Macro 1, Macro 2,
Macro 3 or Macro 4). If you want to select the
displayed macro, wait for 2 seconds without
pressing any key and the parameters of this macro
will be set.
Selects one of the paper paths. The parameters of
the displayed path are set pressing the SHIFT key.
Scrolls the menu and macro functions backward .
FONT Key
FONT
PARK
→
18
Normal
Function
Shift
Function
Program
Function
Selects the font to be used with the currently
selected pitch. The selected font is valid until the
printer is turned off.
Parks the paper in the currently selected paper
path.
Scrolls the menu and macro functions forward.
A78408739-002
Configuring the Printer
Key Combination
PROGRAM
+ SHIFT
Normal
Function
ONLINE +
MACRO +
SHIFT
Normal
Function
A78408739-002
When the printer is on line without printing or
printing data (READY indicator lit) or when the
printer is unable to receive and print data but
there is still data in the input buffer (READY
indicator
blinks)
press
these
two
keys
contemporaneously, the printing noise level
toggles between normal (QUIET PRINT OFF) and
reduced noise level (QUIET PRINT ON).
When the printer is in paper end condition (READY
indicator unlit), the printing noise level function is
disabled.
Lock or unlock the access to the printer setups. See
later “How to Lock/Unlock the Access to the Printer
Setups” section.
19
Configuring the Printer
Printer Setups
The main printer setup parameters can be selected via the operator panel.
The setup parameters are divided into two printer menus, the Power-On
Configuration, that allows a complete configuration at installation time
according to the hardware and the emulation types, and the Program Setup,
that allows you to set the functions that are the most useful in your daily job.
This settings can be selected when the printer is in online without printing
or offline (READY indicator unlit). These settings can be stored in the NVM.
Entering the Printer Setups
•
Press the PROGRAM key and keep it pressed at the printer power on until the
RELEASE KEY message is displayed to select the Power-On Configuration.
•
Press the PROGRAM key when the printer is online without printing or
offline (READY indicator unlit) to select the Program Setup.
Moving within the Printer Setups
The arrow keys ↑, ↓, ← , → are used to move within the different functions
inside the Printer Setups. See the following description of the Menu items.
Leaving the Printer Setups
•
In the Power-On Configuration pressing the PROGRAM key the printer
exits from the menu and the new settings will be automatically saved.
•
In the Program Setup pressing the PROGRAM key, the following choice is
offered for the storage of the values set:
STORE? QUIT
STORE? SAVE
STORE? CURRENT
The new settings are not activated and the old settings
remain valid.
The new settings are stored permanently in the NVM
(Non Volatile Memory).
The new settings remain valid until the printer is
turned off.
Press the → or ← keys to scan these selections forward and backwards.
When the desired setting is displayed, press the PROGRAM key to exit from
the menu.
20
A78408739-002
Configuring the Printer
Power-On Configuration
The default values of the various functions are indicated in bold.
Entering the Power-On Configuration
1. Make sure that the printer is turned off.
2. Press and hold the PROGRAM key pressed while powering on the printer until
the RELEASE KEY message is displayed. As soon as the PROGRAM key gets
released, the following message will be displayed:
9078 plus
or
then,
9078D plus
PRINT OUT? NO
The following figure shows the structure of the Power-On Configuration and
how to move inside the Setup.
Main Structure
Print out? NO
Print out? YES
Low. Jam Sens. Y
Low. Jam Sens. N
Upp. Jam Sens. Y
Upp. Jam Sens. N
Parall Interface
Parallel Interface Settings
Serial Interface
Serial Interface Settings
Functions
Functions Block
Back to MFG? NO
Back to MFG? YES
The functions concerning the interfaces group the parameters for the
configuration of the interfaces.
The setup item Functions groups the following printer functions:
•
•
•
•
•
•
•
•
•
•
•
Paper overlay (9078 plus model only),
Paper loading sequence,
Buzzer setting,
Quick cut sheet loading (9078 plus model only),
Ribbon type,
Code bar density,
Text printing direction,
Graphics printing direction,
Bar code printing direction,
Paper path at power on,
Language of the display messages.
A78408739-002
21
Configuring the Printer
Printout of the Printer Settings
PRINT OUT? NO
→ or ←
PRINT OUT? YES
↓
PARALL INTERF
PRINT OUT? NO
PRINT OUT? YES
The Setup is not printed.
The printer setup is printed showing the currently
selected values. The printout starts as soon as you select
this value.
Enable/Disable Lower Tractor Jam Sensor
PRINT OUT? NO
↑
LOW. JAM SENS. Y
LOW. JAM SENS. N
↓
UPP. JAM SENS. Y
LOW. JAM SENS. Y
LOW. JAM SENS. N
→ or ←
→ or ←
Enables the paper jam sensor located in the Lower Push
Tractor.
Disables the paper jam sensor located in the Lower
Push Tractor.
When the cutter option is used, the jam sensor should be enabled for higher cut
precision.
Enable/Disable Upper Tractor Jam Sensor (only 9078D model)
LOW. JAM SENS. Y
↑
UPP. JAM SENS. Y
UPP. JAM SENS. N
↓
PARALL INTERFACE
UPP. JAM SENS. Y
UPP. JAM SENS. N
22
→ or ←
→ or ←
Enables the paper jam sensor located in the Upper Push
Tractor.
Disables the paper jam sensor located in the Upper
Push Tractor.
When the cutter option is used, the jam sensor should be enabled for higher cut
precision.
A78408739-002
Configuring the Printer
Parallel Interface
This menu defines the use of the parallel interface
according to the interface specific parameters.
and is structured
Parallel Interface Parameters
Parall. Interface
I/F Parallel Cx
1284 Bidir I/F
Select-In Host
Select-In On
Data Bits 8
Data Bits 7
Dedic. Buffer 256
Dedic. Buffer ...
Emul. EPSON ...
Emul. IBM ...
Char. Set ...
Char Set ...
Nation ...
Nation ...
Auto CR ...
Auto CR ...
Auto LF ...
Auto LF ...
20 CPI IBM ...
Serial InterfaceENU BLOCK
Setting the Interface Parameters
Interface Type
PRINT OUT? NO
↓
PARALL INTERFACE
↓
SERIAL INTERFACE
I/F 1284 BIDIR
CX PARALLEL I/F
A78408739-002
→
PARALL INTERFACE
↑
I/F 1284 BIDIR
CX PARALLEL I/F
↓
SELECT-IN HOST
→ or ←
→ or ←
Bidirectional IEEE 1284 parallel interface.
Centronics type parallel interface (monodirectional)
23
Configuring the Printer
Setting the Select-In Signal
I/F 1284 BIDIR.
↑
SELECT-IN HOST
SELECTIN ON
↓
DATA BITS 8
SELECT-IN ON
SELECT-IN HOST
→ or ←
→ ορ ←
The SELECT-IN signal of the parallel interface is ignored
and treated always as ON.
The printer checks the SELECT-IN signal coming from
the host.
Number of Data Bits
SELECT-IN HOST
↑
DATA BITS 8
DATA BITS 7
↓
DEDIC.BUFFER 2K
→ or ←
→ or ←
Selection of the number of data bits: 7 or 8
Input Buffer Size
DATA BITS 8
↑
DEDIC.BUFFER256
DEDIC.BUFFER 2K
DEDIC.BUFFER12K
DEDIC.BUFFER32K
DEDIC.BUFFER64K
↓
EMUL. EPSON LQ
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
Selects the input buffer size. The DLL is available when the buffer size is
set to 12K
Printer Emulation
DEDIC.BUFFER2K
↑
EMUL. IBM XL24
EMUL. IBM XL24 AGM
EMUL. IBM 2391
EMUL. EPSON LQ
↓
CHAR. SET CS2
EMUL.IBM XL24
EMUL.IBM XL24 AGM
EMUL.IBM 2391
EMUL EPSON LQ
24
→ or ←
→ or ←
→ or ←
→ or ←
The printer uses the IBM Proprinter XL24e emulation.
The printer uses the IBM Proprinter XL24 AGM emulation.
The printer uses the IBM Personal 2391 emulation.
The printer uses the EPSON LQ 1050/2550 emulation
A78408739-002
Configuring the Printer
EPSON Character Sets
EMUL. EPSON LQ
↑
CHAR. SET CS1
CHAR. SET CS2
CHAR. SET ITALIC
↓
NATION CP437
→ or ←
→ or ←
→ or ←
These items select the character set to be used in EPSON emulation.
IBM Character sets
EMUL. IBM
↑
CHAR. SET CS1
CHAR. SET CS2
↓
NATION CP437
→ or ←
→ or ←
These items select the character set to be used in IBM Proprinter emulation.
EPSON National Character sets
CHAR. SET CS2
↑
NATION CP437
NATION ...
NATION LATIN A1
↓
AUTO CR YES
→ or ←
→ or ←
→ or ←
The following national character sets are available:
CP 437(*)
CP 853
CP 863
CP 877
ISO 8859/4
ISO 8859/15
SWEDEN
SPAIN2
CP437 G
CP 855
CP 864
GOST
ISO 8859/5
USA
ITALY
LATIN A1
96 GREEK
CP 857
CP 865
TASS
ISO 8859/6
FRANCE
SPAIN1
CP850
CP 858
CP 866
ISO 8859/1
ISO 8859/7
GERMANY
JAPAN
CP851
CP 860
CP 867
ISO 8859/2
ISO 8859/8
ENGLAND
NORWAY
CP 852
CP 862
CP 876
ISO 8859/3
ISO 8859/9
DENMARK1
DENMARK2
The CP 858 and ISO 8859/15 character sets contain the Euro character.
IBM National Character Sets
CHAR. SET CS2
↑
NATION CP437
NATION ...
NATION 8859- 15
↓
AUTO CR YES
A78408739-002
→ or ←
→ or ←
→ or ←
25
Configuring the Printer
The following national character sets can be selected:
CP 437(*)
CP 853
CP 863
CP 877
ISO 8859/4
ISO 8859/15
CP437 G
CP 855
CP 864
GOST
ISO 8859/5
96 GREEK
CP 857
CP 865
TASS
ISO 8859/6
CP850
CP 858
CP 866
ISO 8859/1
ISO 8859/7
CP851
CP 860
CP 867
ISO 8859/2
ISO 8859/8
CP 852
CP 862
CP 876
ISO 8859/3
ISO 8859/9
The CP 858 and ISO 8859/15 character sets contain the Euro character.
CR Code Behavior
NATION xxx
↑
AUTO CR NO
AUTO CR YES
↓
AUTO LF NO
AUTO CR NO
AUTO CR YES
→ or ←
→ or ←
No automatic carriage return is performed after a LF, VT or ESCJ
code.
The printer performs an automatic carriage return after a
LF, VT or ESCJ code .
LF Code Behavior
AUTO CR NO
↑
AUTO LF NO
AUTO LF YES
AUTO LF HOST (Parallel interface only)
↓
20 CPI IBM NO
or
PARALL INTERFACE
AUTO LF NO
AUTO LF YES
AUTO LF HOST
(Parallel
interface only)
→ or ←
→ or ←
→ or ←
No Automatic LF after CR.
Automatic LF after CR.
Only in EPSON emulation. The printer checks the
AUTOFEEDXT signal coming from the host and executes
an automatic LF after CR, if the signal is low .
IBM Compressed Printing
These items are displayed only, if the IBM emulation is selected.
AUTO LF NO
↑
20 CPI IBM NO
20 CPI IBM YES
↓
PARALL INTERFACE
20 CPI IBM NO
20 CPI IBM YES
26
→ or ←
→ or ←
The compressed printing is performed at 17,1 cpi.
The compressed printing is performed at 20 cpi.
A78408739-002
Configuring the Printer
Serial Interface
This menu defines the use of the serial interface and is structured according
to the interface specific parameters.
Serial Interface Parameters
Serial Interface
Serial I/F No
Serial I/F ...
Baud 300
Baud ...
Data Bits 8
Data Bits 7
Parity None
Parity ...
Handshake DTR
Handshake XONXOF
Connect. local
Connect. remote
Dedic. Buffer 256
Dedic. Buffer ...
Emul. EPSON
Emul. IBM ...
Char. Set ...
Char Set ...
Nation ...
Nation ...
Auto CR ...
Auto CR ...
Auto LF ...
Auto LF ...
20 CPI IBM ...
Functions
onsNU BLOCK
Setting the Interface Parameters
Interface Type
PARALL INTERFACE
↑
SERIAL INTERFACE
↓
FUNCTIONS
SERIAL I/F NO
SERIAL I/F 232
SERIAL I/F 422
A78408739-002
→
SERIAL INTERFACE
↑
SERIAL I/F NO
SERIAL I/F 232
SERIAL I/F 422
↓
BAUD 9600
→ or ←
→ or ←
→ or ←
The serial interface is disabled.
Defines the usage of the serial interface RS-232/C.
Defines the usage of the serial interface RS-422/A.
27
Configuring the Printer
Baud Rate
SERIAL I/F NO
↑
BAUD 300
BAUD 600
BAUD 1200
BAUD 2400
BAUD 4800
BAUD 9600
BAUD 19200
BAUD 38400
↓
DATA BITS 8
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
The baud rate is selected in bits per second. The above values can be
selected.
Number of Data Bits
BAUD 9600
↑
DATA BITS 8
DATA BITS 7
↓
PARITY NONE
→ or ←
→ or ←
Selection of the number of data bits: 7 or 8.
Parity Check
DATA BITS 8
↑
PARITY NONE
PARITY ODD
PARITY EVEN
PARITY MARK
PARITY SPACE
↓
HANDSHAKE DTR
PARITY NONE
PARITY ODD
PARITY EVEN
PARITY MARK
PARITY
SPACE
28
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
Data does not have a parity bit, i.e. 8 bit data are
transferred and the parity check is disabled
Parity check is enabled for odd parity
Parity check is enabled for even parity
Parity check is disabled and the transmitted parity bit is
always a Mark
Parity check is disabled and the transmitted parity bit is
always a Space
A78408739-002
Configuring the Printer
Handshake Protocol
PARITY NONE
↑
HANDSHAKE DTR
HANDSHAKE XONXOF
↓
CONNECTION LOCAL
HANDSHAKE DTR
HANDSHAKE
XONXOF
→ or ←
→ or ←
The Handshake is performed using the DTR Protocol.
The Handshake is performed using the XON-XOFF
Protocol.
Connection Type
HANDSHAKE DTR
↑
CONNECTION LOCAL
CONNECT. REMOTE
↓
DEDIC.BUFFER 2K
→ or ←
→ or ←
Selects the connection type: local or remote.
Input Buffer Size
See the description of the parallel interface.
Printer Emulation
See the description of the parallel interface.
EPSON Character Sets
See the description of the parallel interface.
IBM Character sets
See the description of the parallel interface.
EPSON National Character sets
See the description of the parallel interface.
IBM National Character Sets
See the description of the parallel interface.
CR Code Behavior
See the description of the parallel interface.
LF Code Behavior
See the description of the parallel interface.
A78408739-002
29
Configuring the Printer
IBM Compressed Printing
See the description of the parallel interface.
Functions
This item groups various printer functions, with which you can configure the
printer.
9078 plus model Functions Group Parameters
Functions
Paper Overly? No
Paper Overly?Yes
Sequence No
Sequence ...
Buzzer Yes
Buzzer No
Quick Yes
Quick No
Ribbon Black
Ribbon Color
Bar code 60 cpi
Bar code 90 dpi
Text Direct BI
Text Direct UNI
Graph Direct BI
Graph Direct UNI
Bar Code BI
Bar Code UNI
P.On Path Macro
P.On Path Last
Menu ENGLISH
Menu ...
Back to Mfg? NoBak to onsNU BLOCK
9078D plus model Functions Group Parameters
Functions
Sequence No
Sequence ...
Buzzer Yes
Buzzer No
Ribbon Black
Ribbon Color
Bar code 60 dpi
Bar code 90 dpi
Text Direct BI
Text Direct UNI
Graph Direct BI
Graph Direct UNI
Bar Code BI
Bar Code UNI
P.On Path Macro
P.On Path Last
Menu ENGLISH
Back to Mfg? No Bak to onsNU BLOCK
30
Menu ...
A78408739-002
Configuring the Printer
Setting the Functions Group Items
SERIAL INTERFACE
↑
FUNCTIONS
↓
RETURN TO MFG: NO
→
FUNCTIONS
↑
PAPER OVERLY NO
SEQUENCE NONE
↓
(9078 plus model)
(9078D plus model)
If your printer is the 9078 plus model, go ahead the next item. If your printer
is the 9078D plus model, go directly to Paper Loading Sequence item.
Paper Overlapping (9078 plus model only)
FUNCTIONS
↑
PAPER OVERLY NO
PAPER OVERLY YES
↓
SEQUENCE NONE
→ or ←
→ or ←
PAPER OVERLY NO
When feeding a cut sheet through the manual entry
slot, the fanfold paper must be parked.
PAPER OVERLY YES A single sheet can be fed simultaneously with a fanfold.
If the printer is using the Push Pull paper feed mode the Overlay Function cannot
be selected. Only the Paper Overlay No item appears.
Paper Loading Sequence
In the 9078 plus model, this item is displayed only if the ASF is installed. In
the 9078D plus model, this item is displayed if the ASF or the upper tractor
is installed.
FUNCTIONS (9078D plus model)
or
PAPER OVERLY NO (9078 plus model)
↑
SEQUENCE NONE
SEQ. 1+2 PUSH (9078D plus model only)
SEQUENCE ASF1+2
SEQUENCE ASF123
↓
BUZZER YES
SEQUENCE NONE
SEQ. 1+2 PUSH
A78408739-002
→ or ←
→ or ←
→ or ←
→ or ←
The paper is fed only through the path selected by
operator panel.
The paper is fed firstly through the lower push path and
successively
through
the
upper
push
path
(9078D plus model only).
31
Configuring the Printer
SEQUENCE
ASF1+2
This item appears only, if the automatic sheet feeder is
installed. The paper is fed from the first bin until this bin
is out of paper. Then the paper is fed from the second bin.
This item appears only, if the automatic sheet feeder is
installed. The paper is fed from the first bin until this bin
is out of paper. Then the paper is fed from the second bin
and finally from the third bin.
SEQUENCE
ASF123
Enable/Disable the Buzzer
SEQUENCE NONE
↑
BUZZER YES
BUZZER NO
↓
QUICK YES
or
BLACK RIBBON
→ or ←
→ or ←
Enable or disables the buzzer.
Quick Manual Loading through the Manual Slot (9078 plus model only)
BUZZER YES
↑
QUICK NO
QUICK YES
↓
BLACK RIBBON
QUICK NO
QUICK YES
→ or ←
→ or ←
The single sheet in the manual path is loaded by the operator.
The printer is then disabled.
The single sheet in the manual path is loaded automatically.
The printer is then enabled.
Ribbon Type Selection
QUICK YES
or
BUZZER YES
↑
BLACK RIBBON
COLOR RIBBON
↓
BAR CODE 60 DPI
→ or ←
→ or ←
Selects the ribbon type to be used with the printer: black or color.
Bar Code Density
BLACK RIBBON
↑
BAR CODE 60 DPI
BAR CODE 90 DPI
↓
TEXT DIRECT BI
→ or ←
→ or ←
Selects the bar code print density: 60 or 90 dpi.
32
A78408739-002
Configuring the Printer
Text Print Direction
BAR CODE 60 DPI
↑
TEXT DIRECT BI
TEXT DIRECT UNI
↓
GRAPH DIRECT BI
→ or ←
→ or ←
Selects the print direction for text: bidirectional or unidirectional.
Graphics Print Direction
TEXT DIRECT BI
↑
GRAPH DIRECT BI
GRAPH DIRECT UNI
↓
BAR CODES UNI
→ or ←
→ or ←
Selects the print direction for graphics: bidirectional or unidirectional.
Bar Codes Print Direction
GRAPH DIRECT BI
↑
BAR CODES BI
BAR CODES UNI
↓
P. ON PATH MACRO
→ or ←
→ or ←
Selects the print direction for bar codes: bidirectional or unidirectional.
Paper Path at Power-On
BAR CODES UNI
↑
P. ON PATH MACRO
P. ON PATH LAST
↓
MENU ENGLISH
P. ON PATH MACRO
P. ON PATH LAST
→ or ←
→ or ←
The paper path at power-on is the one from the
default Macro.
The paper path at power-on is the last one that was
selected before the printer was powered off.
Selection of the Language of the Display Messages
P. ON PATH MACRO
↑
MENU ENGLISH
MENU ITALIANO
MENU FRANCAIS
MENU ESPANOL
MENU DEUTSCH
↓
FUNCTIONS
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
These items are self explaining.
A78408739-002
33
Configuring the Printer
See also “Selecting the Display Language” before in this manual.
Resetting to Factory Default Values
With the BACK TO MFG function it is possible to reset all items in the Power
On Configuration and in the Program Setup to their factory default values.
This may be useful if you do not remember the values you set in the menus,
or because you simply changed you mind about the settings you have just
done. The default values for the menu items are indicated in bold.
FUNCTIONS
↑
BACK TO MFG: NO
↓ or PROG
PRINT OUT ?
→ or ←
BACK TO MFG: YES
If you want to select BACK TO MFG:YES, you have to exit from this item
using the ↑ or the ↓ key, in order to confirm the selection of this value.
At this point, the Power On Configuration Setup procedure is finished. If you
exit pressing the ↓ and the PROGRAM key, the new settings will be saved.
Do not power off the printer before all data have been written into the NVM
and the printer has returned online.
34
A78408739-002
Configuring the Printer
Program Setup
The default values of the various functions are indicated in bold.
Entering the Program Setup
Press the PROGRAM key when the printer is turned on and is offline or online
without printing. The following message will be displayed:
PRINT OUT? NO
The following figure shows the structure and how to move inside the
Program Setup.
Main Structure
Print out? No
Print out? Yes
User Macro
M acro# 1
Line sp. 6 lpi
...
…
M acro#4
Line sp. ...
M ACRO PARAM ETER BLOCK
Next Macro? No
Next Macro? Yes
Config. Menu? N o
Config. Menu? Yes
Hex Dum p? N o
Hex Dum p? Yes
Parall. Interface
Tear adjust 0
Tear adjust …
Serial Interface
Cut adjust 0
Cut adjust …
…
CONFIGURATION M ENU BLOCK
The items define the following parameters:
•
•
•
•
•
Four user macros
The direct access to the Power-On Configuration
Hexadecimal printout
Tear-Off adjustment
Cut adjustment
A78408739-002
35
Configuring the Printer
Printout of the Printer Settings
PRINT OUT? NO
↓
USER MACRO
PRINT OUT? NO
PRINT OUT? YES
→ or ←
PRINT OUT? YES
The Setup is not printed.
The printer setup is printed. The printout starts as
soon as you select this value.
NOTE: The Program setup printout indicates:
•
•
•
the currently selected values,
the current selected macro is marked with the #x# symbols (USER MACRO
#x#),
the current firmware release.
USER MACRO
The USER MACRO item allows to prepare four printing environments
(MACRO#1, MACRO#2, MACRO#3 and MACRO#4). Each macro is composed of
a group of parameters which define a configuration that can then be recalled
to easily set the printer for four printing environments.
SELECTION OF THE USER MACRO
PRINT OUT? NO
↓
USER MACRO
↓
CONFIG MENU NO
→
USER MACRO
↑
MACRO # 1
MACRO # 2
MACRO # 3
MACRO # 4
↓
LINE SP. 6 LPP
→ or ←
→ or ←
→ or ←
→ or ←
Selection of the macro for which you intend to set the parameters.
36
When a new macro is selected and the fanfold paper is present in the paper
path set in the previous macro, it will be automatically parked (PARK: SURE? is
displayed).Tear off this fanfold paper to avoid paper jams and press PARK key.
A78408739-002
Configuring the Printer
USER MACRO PARAMETERS
U ser m a cro
M acro # 1
M acro #2
M acro # 3
M acro #4
Lin e S p. 6 lpi
Lin e S p. ...
Lin e S p. Lock N o
L e S p Lock Yes
Lin
Len gth 1 Line
Len gth ...
Top of F orm 0
Top of F orm ...
S kipover 0
S kipover …
D raft M ode H S
D raft M ode N orm
Q u ality L Q
Q u ality …
Fo nt D raft
Fo nt …
P itch 10 cpi
P itch …
P itch Lo ck N o
P itch Lo ck Yes
Left M argin 0
Left M argin ...
R ig ht M argin 2
R ig ht M argin ...
S lash Ze ro N o
S lash Ze ro Yes
P ath L ow er P ush
P ath ...
Tear N orm al
Tear …
V T:F F+ C ut
V T: …
S tron g Im pact
S oft Im pact
P erfo r. S afe N o
P erfo r. S afe? Yes
A utogap 0
A utogap ...
Tuning:H oriz 0
Tuning:H oriz ...
Tuning:Vert 0
Tuning:Vert ...
M acro->M FG N o
M acro->M FG Yes
N ext M acro? N o
N ext M acro? Yes
C onfig. M e nu N o
A78408739-002
37
Configuring the Printer
Line Spacing
MACRO# 1
→
MACRO # 1
↑
LINE SP. 6 LPP
LINE SP. 8 LPP
LINE SP. 12 LPP
LINE SP 3L/30MM
LINE SP 4L/30MM
LINE SP 6L/30MM
LINE SP 8L/30MM
LINE SP 12L/30MM
↓
LINE SP LOCK NO
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
These values define the line spacing in lines/inch (6, 8, 12) or in lines per 30
mm (3, 4, 6, 8, 12).
Line Spacing Lock
LINE SP. 6 LPI
↑
LINE SP. LOCK NO
LINE SP. LOCK YES
↓
LENGTH xxx
LINE SP. LOCK NO
LINE SP. LOCK YES
→ or ←
→ or ←
Setting this item, the value set for vertical spacing can
be changed by software or operator panel
Setting this item, the value set for vertical spacing
cannot be changed by software but only by operator
panel.
Page Length
LINE SP. LOCK NO
↑
LENGTH 1 LINE
LENGTH . .. LINES
LENGTH 244 LINES
LENGTH A5
LENGTH A4
LENGTH A3
LENGTH A2
LENGTH LEGAL
LENGTH LETTER
↓
TOP OF FORM 0
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
These items set the page length for fanfold paper in number of lines
depending on the current vertical spacing. For the single sheets the page
format can be specified in number of lines or the standard formats LETTER,
LEGAL, A2, A3, A4, A5. Default value is 66 lines.
38
A78408739-002
Configuring the Printer
Top of Form
LENGTH Xx
↑
TOP OF FORM 0
TOP OF FORM ...
TOP OF FORM xxx
↓
SKIPOVER 0
→ or ←
→ or ←
→ or ←
These items set the top of form. The values range between 0 and the page length - 1.
Skip Over Perforation
TOP OF FORM 0
↑
SKIPOVER 0
SKIPOVER ...
SKIPOVER xxx
↓
DRAFT MODE HS
→ or ←
→ or ←
→ or ←
These items set the skipover perforation. The values range between 0 and the page
length - 1.
Draft Print Mode
SKIPOVER 0
↑
DRAFT MODE HS
DRAFT MODE NORM
↓
QUALITY LQ
→ or ←
→ or ←
DRAFT MODE HS
The printer performs the draft printing at high speed.
DRAFT MODE NORM The printer performs the draft printing at normal speed.
Quality Print Mode
DRAFT MODE HS
↑
QUALITY LQ
QUALITY NLQ
QUALITY HS LQ
QUALITY HS NLQ
↓
FONT Draft
QUALITY LQ
QUALITY NLQ
QUALITY HS LQ
QUALITY HS NLQ
A78408739-002
→ or ←
→ or ←
→ or ←
→ or ←
The printer performs the Letter Quality printing.
The printer performs the Near Letter Quality
printing.
The printer performs the Letter Quality printing at high
speed.
The printer performs the Near Letter Quality printing at
high speed.
39
Configuring the Printer
Font Selection
QUALITY LQ
↑
FONT Draft
FONT Courier
FONT OCR-B
FONT Gothic
FONT Script
FONT OCR-A
↓
PITCH 10 CPI
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
Selects the fonts OCR-A, OCR-B only if the pitch 5 cpi or 10 cpi has been selected.
Pitch Selection
FONT Draft
↑
PITCH 5 CPI
PITCH 6 CPI
PITCH 7.5 CPI
PITCH 8.5 CPI
PITCH 10 CPI
PITCH 12 CPI
PITCH 15 CPI
PITCH 17.1 CPI
PITCH 20 CPI
PITCH 24 CPI
PITCH PROP.
↓
PITCH LOCK NO
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
These items are self-explaining.
Pitch Lock
PITCH 10 CPI
↑
PITCH LOCK NO
PITCH LOCK YES
↓
LEFT MARGIN ---
PITCH LOCK NO
PITCH LOCK YES
→ or ←
→ or ←
The pitch can be changed by software or operator panel.
The pitch can be changed ONLY by operator panel.
Left Margin
PITCH LOCK NO
↑
LEFT MARGIN 0
LEFT MARGIN ...
LEFT MARGIN xxx
↓
RIGHT MARGIN 2
→ or ←
→ or ←
→ or ←
The Left Margin is set in number of columns (depending on the current
pitch) starting from the physical left edge.
40
A78408739-002
Configuring the Printer
Right Margin
LEFT MARGIN 0
↑
RIGHT MARGIN. 2
RIGHT MARGIN. ...
RIGHT MARGIN. xxx
↓
SLASH ZERO NO
→ or ←
→ or ←
→ or ←
The Right Margin is set in number of columns (depending on the current
pitch) starting from the physical left edge. The default value is 136.
Zero Character Printing
RIGHT MARGIN 2
↑
SLASH ZERO NO
SLASH ZERO YES
↓
LOWER PUSH
→ or ←
→ or ←
You can select the Zero character printing with or without a slash.
Paper Path Selection
This function defines the default paper path for the current macro.
SLASH ZERO NO
↑
PATH LOWER PUSH
PATH UPPER PUSH (9078D plus model only)
PATH MANUAL FORM (9078 plus model only)
PATH PUSH PULL
ASF 1
ASF 2
ASF 3
↓
TEAR NORMAL
PATH LOWER PUSH
PATH UPPER PUSH
PATH MANUAL FORM
PATH PUSH PULL
ASF1
ASF2
ASF3
A78408739-002
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
Paper loading with the lower push tractor.
Paper loading with the upper push tractor (9078D
plus model only).
Paper loading using the manual single sheet path
(9078 plus model only).
Paper loading using the lower push tractor and the
rear pull tractor.
Paper loading from the first bin of the ASF, if
installed.
Paper loading from the second bin of the ASF, if
installed.
Paper loading from the third bin of the ASF, if
installed.
41
Configuring the Printer
Tear-Off Mode
LOWER PUSH
↑
TEAR NORMAL
TEAR AUTOM.
LABEL
TEAR NO
ENABLE CUTTER
↓
VT:FF+CUT
TEAR NORMAL
TEAR AUTOM.
LABEL
TEAR NO
ENABLE
CUTTER
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
The Tear-Off Function is performed pressing the ONLINE
key when the printer is offline .
When the printer is not receiving any data, the paper is
moved to the Tear-Off position. It is returned to the TearOff position as soon as it receives printing data.
This item must be set when printing on labels, in order to
avoid paper jams. The paper does not execute any
backward movement.
The paper does not execute any backward movement.
This selection enables the cutter option and appears only,
if the cutter option is installed.
See also “How to Use the Tear-Off Function” later in this chapter.
Cutter mode
TEAR NORMAL
↑
VT: FF + CUT
VT: LF+CUT
VT: VT
CUT EACH PAGE
CUT PAPER CHANGE
↓
STRONG IMPACT
VT: FF + CUT
VT: LF + CUT
VT: VT
CUT EACH PAGE
CUT PAPER CHANGE
42
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
When the printer receives a VT command, it performs
a form feed and then cuts the paper.
When the printer receives a VT command, it performs
a line feed and then cuts the paper.
When the printer receives a VT command, it performs
a vertical tabulation.
Selecting this item, the printer cuts the paper at the
end of each page according to the selected page
length.
Selecting this item, the printer cuts the paper when it
receives a paper path change command before
changing the paper path.
A78408739-002
Configuring the Printer
Print Impact Strength
VT:FF+CUT
↑
STRONG IMPACT
SOFT IMPACT
↓
PERFOR. SAFE NO
→ or ←
→ or ←
STRONG IMPACT
SOFT IMPACT
The impact strength of the print head is set for printing
on multicopy paper.
The impact strength of the print head is set for printing
on single paper or few copies. The printing noise is
reduced.
Paper Perforation
This function allows to move the print head aside the paper when the fanfold
paper perforation passes between the mylar and the print bar, to avoid paper
jams. If the use of single sheets is selected, this item is not displayed.
SOFT IMPACT
↑
PERFOR. SAFE NO
PERFOR. SAFE YES
↓
AUTOGAP 0
→ or ←
→ or ←
PERFOR. SAFE NO
The function is disabled. The print head remains in its
position, when the perforation of the paper passes.
PERFOR. SAFE YES The function is enabled. The print head is moved
aside, when the perforation passes.
Adjusting the Distance of the Print Head
PERFOR. SAFE NO
↑
AUTOGAP -5
AUTOGAP ...
AUTOGAP +3
MANUAL GAP
FIXED GAP 0.3
FIXED GAP ...
FIXED GAP 9.3
↓
TUNING.HORIZ 0
AUTOGAP xxx
MANUAL GAP
FIXED GAP xxx
A78408739-002
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
→ or ←
Selecting one of these values sensing the paper thickness.
Negative values reduce the distance between the print head
and the paper. Default value is AUTOGAP 0.
Selecting this item, the print head must be adjusted
manually.
Selecting one of these values the printer adjusts the print
head gap to a fixed distance.
43
Configuring the Printer
Horizontal Character Tuning
AUTOGAP 0
↑
TUNING.HORIZ 0
TUNING.HORIZ ...
TUNING.HORIZ 60
↓
TUNING.VERT 0
→ or ←
→ or ←
→ or ←
These values adjust the distance between the left paper margin and the first
print character. The values correspond to 1/120 inch units, i.e. the tuning
ranges between 0 and 0,5 inch.
Vertical Character Tuning
TUNING.HORIZ 0
↑
TUNING.VERT. -30
TUNING.VERT. ...
TUNING.VERT. 360
↓
MACRO -> MFG NO
→ or ←
→ or ←
→ or ←
These values adjust the distance between the top paper margin and the first
printable line. The values correspond to 1/180 inch units, i.e. the tuning
ranges between -1/6 and 2 inch. 0 is the default value.
Resetting the Macro Parameters to the Factory Defaults
TUNING.VERT. 0
↑
MACRO -> MFG NO
MACRO -> MFG YES
↓
NEXT MACRO? NO
MACRO -> MFG NO
MACRO -> MFG YES
→ or ←
→ or ←
The new values set for the macro parameters will be
the used.
The values set for the macro parameters will be reset
to their factory defaults.
Selecting Another Macro
MACRO -> MFG NO
↑
NEXT MACRO? NO
↓
CONFIG MENU NO
→ or ←
NEXT MACRO? YES
↓
MACRO # 1
To pass over to another macro, select NEXT MACRO YES. Pressing the ↓ or ↑
key the item MACRO#1 is displayed, then press the → key to pass over to
MACRO#2 (MACRO CHANGING is displayed).
44
A78408739-002
Configuring the Printer
When passing over from one macro to another, the fanfold paper loaded from the
paper path, selected in the previous macro, will be automatically parked (PARK:
SURE? is displayed). Tear off this fanfold paper to avoid paper jams and press
PARK key.
You can now set the parameters for Macro#2 as described above. In this way
you prepare the second printing environment .
Passing over from one macro to the other then sets two different printing
environments.
Passing over to the Power-On Configuration
At this point of the menu, it is possible to pass over to the Power On
Configuration Functions Setting.
NEXT MACRO NO
↑
CONFIG MENU NO
↓
HEX DUMP NO
→ or ←
CONFIG MENU YES
↓
PARALL INTERFACE
These items are self-explaining.
Hexadecimal Dump
CONFIG MENU NO
↑
HEX DUMP NO
↓
TEAR ADJUST: xxxx
→ or ←
HEX DUMP YES
If you select HEX DUMP YES, press the PROGRAM key to set this item. The
hexadecimal printing continues, until the HEX DUMP NO item is selected,
entering again into the Program Setup.
Adjusting the Tear-Off Position
HEX DUMP NO
↑
TEAR ADJUST: - 30
TEAR ADJUST: ...
TEAR ADJUST: +360
↓
STORE? QUIT
TEAR ADJUST: xxxx
→ or ←
→ or ←
→ or ←
These values adjust the distance between the TearOff Perforation and the Tear-Off Bar. The values
correspond to 1/180 inch units, i.e. the tuning ranges
between -1/6 and 2 inch. 0 is the default value.
See also “How to Use the Tear-Off Function”, later in this Chapter".
A78408739-002
45
Configuring the Printer
Adjusting the Cut Position
TEAR ADJUST 0
↑
CUT ADJUST: - 30
CUT ADJUST: ...
CUT ADJUST: +360
↓
STORE? QUIT
CUT ADJUST: xxxx
→ or ←
→ or ←
→ or ←
These values adjust the position in which the paper is
cut. The values correspond to 1/180 inch units, i.e. the
tuning ranges between -1/6 and 2 inch. 0 is the default
value.
Storing the values
TEAR ADJUST: xxxx
↑
STORE? QUIT
STORE? SAVE
STORE? CURRENT
PROG
EXIT
→ or ←
→ or ←
→ or ←
STORE? QUIT
This setting does not save any of the new values set. The
values set previously will be used.
STORE? SAVE
The values set are stored permanently (in the NVM) and
will be used until they are changed by the operator.
STORE? CURRENT The values set are valid until the printer is turned off.
When you turn the printer on again, the values set in the
preceding menu setup will be used.
At this point the Program Configuration Setup is finished. You exit pressing the
PROGRAM key.
How to Select the Paper Path
The paper can be loaded into the printer using different paper paths. The
messages indicating the paper paths are shown only if the corresponding
loading device is installed on the printer.
Proceed as follows:
1. Press the READY key to put the printer offline (the READY indicator is
unlit).
2. Press the PATH key, according to the installed devices the following
messages are displayed:
46
A78408739-002
Configuring the Printer
LOAD LOWER PUSH
LOAD UPPER PUSH
LOAD MANUAL
LOAD PUSH-PULL
LOAD ASF1
LOAD ASF2
LOAD ASF3
For the lower push tractor paper path.
For the upper push tractor paper path (9078D plus model only).
For the manual cut sheet paper path (9078 plus model only).
For the paper path using the lower push tractor and the optional rear pull
tractor.
Loading a cut sheet from the first bin of the automatic sheet feeder.
Loading a cut sheet from the second bin of the automatic sheet feeder.
Loading a cut sheet from the third bin of the automatic sheet feeder.
•
To load fanfold paper go to “Loading Fanfold Paper Using the Lower
Tractor” or “Loading Fanfold Paper Using the Upper Tractor”.
•
To load manual cut sheets go to “Loading Cut Sheets”.
•
For using paper with the Automatic Sheet Feeder option, consult the
documentation you receive together with the option.
When a new paper path is selected, the paper loaded in the printer is
automatically parked/ejected.
How to Use the Tear-Off Function
This function is used to match the paper perforation with the tear-off bar.
For this function the following values must be set:
Selection of the Paper Size
1. Press the PROGRAM key when the printer is disabled or enabled without
printing to enter the Program Setup.
2. Press the ↓ key and the following message appears:
USER MACRO
3. Press the → key to select the macro for which you want to set the paper
size (MACRO#1,MACRO#2,MACRO#3 or MACRO#4).
4. Once the desired macro is displayed press the ↓ key until the following
parameter is displayed:
LENGTH xx
5. Press the → or ← key until the desired page size is displayed.
6. Press again the PROGRAM key to exit the menu end set the new value.
A78408739-002
47
Configuring the Printer
Adjusting the Tear-Off Position
The default value for the Tear-Off Function is TEAR NORMAL. To check the
Tear-Off Position proceed as follows:
1. To move the paper to the Tear-Off position, press the ON LINE key when
the printer is disabled or enabled without printing.
2. Check if the paper perforation matches the tear-off bar on the printer.
If it does not:
1. Press the PROGRAM key to enter the Program Setup.
2. Press the ↓ key until the following message appears:
USER MACRO
3. Press the → key until the macro for which you want to adjust the tear-off
is displayed (#1, #2, #3 or #4):
MACRO # x
4. Press the ↓ key until the following message is displayed:
TEAR ADJUST xxx
5. Press the → or ← key to scroll the values of this function.
The values below 0 move the tear-off position downwards, values above 0 move
the paper upwards. The values can be set between -30 and 360 at 1/180 inches
(-1/6 to 2 inches).
6. When the desired value is displayed, press the PROGRAM key. The
storage options are displayed.
7. Press the → or ← key, until the following message is displayed:
STORE? SAVE
8. Press the PROGRAM key to exit from the menu.
Selection of the Tear-Off Mode
It is now possible to select the Tear-Off Mode.
1. Press the PROGRAM key when the printer is disabled or enabled without
printing to enter the Program Setup.
2. Press the ↓ key. The following message is displayed:
USER MACRO
48
A78408739-002
Configuring the Printer
3. Press the → key to select the macro for which you want to set the tear-off
mode MACRO#1,MACRO#2,MACRO#3 or MACRO#4).
4. Press the ↓ key, until the following message is displayed:
TEAR NORMAL
Pressing the → or ← key it is now possible to decide how to execute the tear
off function:
TEAR NORMAL
Pressing the ON LINE key the paper is moved to the tearoff position.
Pressing again the ON LINE key, the paper is moved to the
printing position.
If the ON LINE key is not pressed for 10 seconds, the paper
moves automatically back to the print position.
TEAR AUTOMATIC If the printer is not receiving data, the paper is moved
automatically to the tear position.
LABELS
The ON LINE key is disabled for the tear-off function. This
selection is useful when printing on labels.
TEAR NO
The Tear-Off function is disabled
5. Press the PROGRAM key to exit the setup.
A78408739-002
49
Configuring the Printer
How to Lock/Unlock the Access to the Printer
Setups
To prevent not expertise persons changing the printer setup parameters, it is
possible to lock/unlock the access to the printer setups as follows:
•
Press ON LINE, MACRO and SHIFT keys at the same time and keep them
pressed while powering the printer on. As soon as these keys are released, the
following messages will be displayed:
9078 plus
or
9078D plus
then,
MENU LOCKED
Now the access to the printer setups is locked. If the PROGRAM key is pressed, the
LOCKED MENU message is displayed (the PROGRAM key is disabled).
•
If you decide to unlock the printer setup, turn the printer off, then press the
ON LINE, MACRO and SHIFT keys at the same time and keep them pressed
while powering the printer on again. As soon as these keys are released, the
following messages will be displayed:
9078 plus
or
9078D plus
then,
MENU UNLOCKED
50
A78408739-002
Configuring the Printer
How to Handle the Paper Parking
The paper parking is performed in the following cases:
•
At power on, if the paper is loaded in a paper path that is not the default
one, the parking is performed automatically.
•
If the paper is present and the PATH key is pressed to change the paper
path, the printer requests to confirm the parking of the current fanfold
paper (PARK SURE? message is displayed) by pressing the PARK key,
before the paper path is changed, then the paper is loaded in the new
paper path.
•
When parking via SW command, the printer requests to park the paper
(PARK SURE? message is displayed) by pressing the PARK key.
•
When loading paper via SW command in a different paper path, the printer
requests to park the paper in the current paper path (PARK SURE? message
is displayed) by pressing the PARK key, then the printer parks the paper
before loading the paper in the selected path.
•
When changing to a macro using a different paper path, the printer
automatically parks the paper.
In all the above cases, the parking procedure may be interrupted by pressing
the SHIFT key. The display shows PARK ABORTED message.
A78408739-002
51
Paper Handling
Paper Handling
Paper Paths
The following figure shows the paper path configurations.
Low er Push Path
(90 78 plus and 907 8D plu s)
M anua l Pa th
(90 78 plus)
U pper Push Path
(90 78D plus)
Base C onfiguration
W ith Installed Options
Push-P ull Path
(90 78 plus an d 9 078D plus)
Low er Push Tractor
plus Cu tter
(90 78plus and 9078 D plus)
Autom atic Sh eet Feede r
plus
Low er Push Tractor
(90 78 plus and 907 8D plu s)
U pper Push Tractor
plus Cu tter
(90 78D plus)
Paper Specifications
It is important to use the correct paper for obtaining the best performance.
See the information table below:
52
A78408739-002
Paper Handling
Fanfold Paper (9078 plus and 9078D plus models)
Loading Mode
Lower Tractor
Width
Length
Thickness
Copies
2
Weight (g/m ):
- Original
- Other sheets
- Carbon Paper
76 to 432 mm
3 to 17 inches
76 to 609 mm
3 to 24 inches
max.0.635 mm
0.025 inches
1+7
Upper Tractor
(9078D plus model only)
76 to 432 mm
3 to 17 inches
76 to 609 mm
3 to 24 inches
max. 0.635 mm
0.025 inches
1+7
Push-Pull
(option)
76 to 432 mm
3 to 17 inches
76 to 609 mm
3 to 24 inches
max. 0.635 mm
0.025 inches
1+7
55 to 150
45 to 75
35
55 to 150
45 to 75
35
55 to 150
45 to 75
35
Envelopes (9078 plus model only)
Loading Mode
Length
Thickness
Types
Manual Feeding
102 to 559 mm (4 to 22 inches)
Max .variations 3 mm (0.013 inches)
USA 6 (165 x 92 mm)
USA 10 (241 x 105 mm)
Cut Sheets (9078 plus model only)
Loading Mode
Width
Length
Weight
Formats
Thickness
Copies
A78408739-002
Manual Loading
114 to 432 mm (4.5 to 17 inches)
101 to 559 mm (4 to 22 inches)
2
Original:
50-120 g/m
Multiparts:
First Sheet:
Other Sheets:
Carbon Paper:
A5
149 x 210 mm
A4
210 x 297 mm
A3
297 x 420 mm
A2
420 x 554 mm
Letter
8.5 x 11 inches
Legal
8.5 x 14 inches
max. 0.635 mm (0.025 inches)
1 Original + 7 Copies
2
55-75 g/m
2
45-75 g/m
2
14-35 g/m
Portrait & Landscape
Portrait & Landscape
Portrait & Landscape
Portrait
Portrait & Landscape
Portrait & Landscape
53
Paper Handling
Cut Sheets
Cut Sheet Loading Modes
9078 plus model
Cut sheet loading mode is only available for the 9078 plus model.
Cut sheets can be loaded manually, one at a time using the front manual
paper path (manual or automatic loading) or automatically using the ASF
option for large quantities of paper.
Inserting a cut sheet, the fanfold paper is automatically parked with a reverse
movement (if the overlapping is not selected).
Loading Cut Sheets
1. Lift the cut sheets support until it locks in horizontal position.
54
A78408739-002
Paper Handling
2. Position the left paper guide on the cut sheet support for the first printing
column (position 0).
3. Insert a cut sheet along
the left paper guide.
Match the right paper
guide with the sheet
margin.
4. The loading mode of the cut sheet depends on the value set for the QUICK
function in the Power-On Configuration:
Manual loading mode
(QUICK NO)
Automatic loading
(QUICK YES)
A78408739-002
Make sure that the printer is disabled. Insert
a cut sheet onto the front paper support and
press the LOAD/FF key to feed the paper.
Press the ON LINE key to enable the printer.
mode Insert a cut sheet onto the front paper
support, the paper
will
be
loaded
automatically after 2 seconds. The LOAD/FF
key can be used to load the paper into the
printer, before the 2 seconds have passed.
55
Paper Handling
5. To lower the paper feed support, free the paper support holder indicated
in the figure. Press the support down until it locks in place.
Fanfold Paper
Loading Paper Using the Lower Tractor
9078 plus model
9078D plus model
If your printer is the 9078 plus model, make sure that the cut sheets support is
closed before loading the fanfold paper.
1. To select the lower tractor paper path press the PATH key until the display
shows:
LOAD LOWER PUSH
•
If your printer is the 9078D plus model , press the PATH key to select
the lower tractor paper path,. The display shows:
PATH CHANGING
56
A78408739-002
Paper Handling
•
If the fanfold paper is present in the upper tractor paper path, the
printer automatically parks this fanfold before loading the new one.
The display shows:
PARK: SURE?
•
Tear off the fanfold loaded from the upper tractor paper path to avoid
paper jams. Press the PARK key. Then the display shows:
LOAD LOWER PUSH
2. Open the tractor area cover turning is upwards and lay it on the top of
the printer.
•
If your printer is the 9078D
plus model and it is installed
the upper tractor, rotate the
upper tractor
out of the
printer.
A78408739-002
57
Paper Handling
3. Unlock the sprockets of the
Lower tractor moving the
sprocket levers up. Slide the
left sprocket to the first
printing column.
4. Space the paper guides along
the tractor bar. Open the
sprocket covers of the left and
right sprocket
•
58
If your printer is the 9078D plus model, insert the fanfold paper between
the lower and the upper tractor.
A78408739-002
Paper Handling
5. Hold the fanfold paper in front
of the sprockets and insert the
paper perforation on the left
sprocket pins and close the
sprocket cover.
6. Insert the paper on the right
sprocket pins, make sure the
paper goes under the paper
sensor and close the sprocket
cover.
6. Match the left sprocket for the first printing position with the ninth mark
and lock it in place. Adjust the right sprocket gently to remove slack from
the paper.
9
A78408739-002
59
Paper Handling
•
If your printer is the 9078D plus model, reposition the upper tractor in its
initial position
7. Close the tractor area cover. Press the LOAD/FF key to load the paper
into the printer.
8. The paper must be loaded as shown in figure (9078D plus model).
60
A78408739-002
Paper Handling
Loading Paper Using the Upper Tractor
9078D plus model
Fanfold paper loading mode through the upper tractor is only available for the
9078D plus model. To load paper in this way, it is necessary to install the upper
tractor. See before “ Upper Push Tractor Installation" section.
1. Press the PATH key to select the upper tractor paper path. The display
shows:
PATH CHANGING
2. If fanfold paper is present in the lower tractor paper path, the printer
automatically parks this fanfold before loading the new one. The display
shows:
PARK: SURE?
3. Tear off the fanfold loaded from the lower tractor paper path to avoid
paper jams. Press PARK. Then the display shows:
LOAD UPPER TRACTOR
4. Open the tractor area cover turning is upwards and lay it on the top of
the printer.
A78408739-002
61
Paper Handling
5. Space the paper guides along
the tractor bar. Open the
sprocket covers of the left and
right sprocket.
6-
Hold the fanfold paper in
front of the sprockets and
insert the paper perforation on
the left sprocket pins and close
the sprocket cover.
7. Insert the paper on the right
sprocket pins, make sure the
paper goes under the paper
sensor and close the sprocket
cover.
62
A78408739-002
Paper Handling
8. Position the left sprocket for printing and lock it in place. Adjust gently
the right sprocket to remove slack from the paper.
9. Close the tractor area cover. Press the LOAD/FF key to load the paper into
the printer.
10. The paper must be loaded as shown in figure.
A78408739-002
63
Paper Handling
Loading Paper Using the Lower Push Tractor and the
Rear Pull Tractor (option)
9078 plus model
9078D plus model
For loading paper in this way, it is necessary to install the optional rear pull
tractor. See later "Options" section .
With this paper path configuration paper is loaded contemporaneously with
the lower front push tractor and the rear pull tractor. In this way it is
possible to handle stronger paper.
Once the rear pull tractor is installed, the fanfold paper can be loaded only in
push-pull mode.
1. Press the PATH key to select the push-pull paper path. The display shows:
LOAD PUSH-PULL
•
If your printer is the 9078D plus model, press the PATH key to select
the push-pull paper path. The display shows:
PATH CHANGING
•
If the fanfold paper is present in the upper tractor paper path, the
printer automatically parks this fanfold before loading the new one.
The display shows:
PARK: SURE?
•
Tear off the fanfold loaded from the upper tractor paper path to avoid
paper jam. Press the PARK key. Then the display shows:
LOAD PUSH-PULL
2. To load the fanfold paper on the lower push tractor, follow the sequence
Loading Paper Using the Lower Tractor described before.
64
A78408739-002
Paper Handling
3. Take up the slack of the paper exiting from the rear paper slot and rotate
the sprocket bar to align the sprocket pins of the rear tractor with the
paper perforation.
4. Lock the sprocket covers and lower the sprocket levers.
5. Press the ON LINE key to confirm that the paper loading is finished. The
rear tractor engages.
6. The figure shows the correct paper loading.
A78408739-002
65
Printer Maintenance and Troubleshooting
Printer Maintenance and Troubleshooting
Cleaning the Printer
Make sure the printer has been turned off for at least 15 minutes before starting
any cleaning operations.
Periodic cleaning will help keep your printer in top condition so that it will
always provide optimal performance.
•
Use a neutral detergent or water solution on a soft cloth to clean dirt and
grease from the cabinet of the printer.
•
Do not use an abrasive cloth, alcohol, paint thinner or similar agents
because they may cause discoloration and scratching.
•
Be especially careful not to damage the electronic and mechanical
components.
Replacing the Ribbon Cartridge
1. Make sure that the printer is turned off for at least 15 minutes.
Pay attention to the print head because it becomes hot during
operation.
2. Open the top printer cover.
R ib b on G uide
3. Slide the ribbon guide
out of the print head. If
the color kit is installed
on the printer, unlock the
white slider pressing and
holding the lever on the
slider towards the back
of
the
printer
and
contemporaneously
lifting the slider off the C o lo r S lide r
color mechanism.
C o lo r K it
66
A78408739-002
Printer Maintenance and Troubleshooting
4. Remove the used ribbon cartridge by lifting it up.
Now, you are ready to insert the new ribbon cartridge. See before "Ribbon
Cartridge Installation" section.
Printing the Self Test
If you need to know any printer setting, and to check if the printer is working
well, print the self-test.
Proceed as follows:
1. Keep the ON LINE key pressed while powering on the printer until the
display boxes are filled in and the printer stops all motions.
2. When you release the key, the printer starts the self-test printout.
3. To stop the self-test printing, press the ON LINE key again. The printer is
offline.
Error Handling
When an error condition occurs:
•
the printer is disabled;
•
the first message on the display indicates the error, while the second
message gives indicates more details concerning the error conditions.
Press always the ON LINE key to reset the error condition.
A78408739-002
67
Printer Maintenance and Troubleshooting
Error Message Description
Messages
Indication
Solution
A.G.A NOT OPER
ADJUST THE GAP
The automatic gap
adjustment (A.G.A) is not
enabled.
Press the ON LINE key to reset the
error condition. Adjust the print head
gap to a fixed distance. Select the
print head fixed gap adjustment
function in the Program Menu.
•
•
Press the PROGRAM key when
the printer is disabled (READY
indicator unlit) to enter the
Program Setup
Press the ↓ key until the USER
MACRO function is displayed.
Press the → key until the desired
macro is displayed (MACRO#x).
Press the → key to enter the macro
parameters. Press the ↓ key until the
FIXED GAP parameter is displayed.
Press the → o ← keys to select the
fixed gap adjustment values. From
FIXED GAP 1 (simple fanfold paper)
to FIXED GAP 4 (multipart fanfold
paper).
BUFFER OVERFLOW
CHARACTER LOST
An overflow condition
occurs in the buffer (if the
serial interface is
selected).
Turn the printer off and on again, or
press the PROGRAM and ON LINE
key successively and the buffer will
be cleared.
CUTTER ERROR
CUT NOT ALLOWED
An error occurred with
the optional cutter
Turn the printer off and on again. If
the error is not solved, call the
Customer Support.
DATA SET OFF
Press the ONLINE key to reset the
The DSR Signal is not
error condition.
connected to the printer
and is not ready for data
transfer (if the serial
interface is selected).
This condition may
happen in a remote
connection (via modem)
and the DSR (DATA SET
READY) signal is missing.
INTERLOCK ERROR
CHECK INSERTION
Neither the rear tractor
nor the tractor cover are
installed on the printer.
68
Install the rear tractor or the tractor
cover on the printer.
A78408739-002
Printer Maintenance and Troubleshooting
Messages
Indication
Solution
NO PATH AVAILABLE
An electromechanical
failure occurs in the
lower or upper tractor
paper paths.
Call Service.
NO PATH AVAILABLE
PATH CHANGING
An electromechanical
failure occurs in the
lower tractor paper path.
The printer changes
automatically to the cut
sheet paths (Manual or
ASF).
Call Service.
PAPER JAM
CHECK ALL PATHS
A paper jam error
condition occurs in the
paper path
Check all the paper paths and
remove the jammed paper. Press the
ON LINE key to reset the error
condition.
PRINT INTEGRITY
Anomalous print out
because of a possible
print carriage blocking
Do not move the platen knob.
The ribbon of the
cartridge is blocked
Check that the ribbon is correctly
inserted. Turn the tension knob to
make sure that the ribbon is not
jammed. Press the ONLINE key to
reset the error condition
RIBBON BLOCKED
CHECK RIBBON
A78408739-002
Press the ONLINE key to reset the
error condition
69
Options
Options
The Rear Pull Tractor
The rear pull tractor is useful to handle particularly heavy paper.
Installing the Rear Pull Tractor
1. Turn the printer off.
2. Remove the ASF cover, the rear tractor area cover and the two small
tractor fixing area covers.
R e ar tracto r
a rea cover
A S F a rea cove r
Tra ctor fixin g
a rea s co vers
Keep the covers in a safe place, as they must be reinstalled if the rear
tractor is removed.
3. Replace the ASF cover.
70
A78408739-002
Options
4. Insert the rear pull tractor as shown in figure and the corresponding
fixing area covers (with the slot) as shown in figure.
5. Turn the printer on.
The paper can be loaded in push-pull mode. See before "Loading Paper Using
the Lower Push Tractor and the Rear Pull Tractor".
Removing the Rear Pull Tractor
1. Push the lever on the rear pull tractor down and lift the tractor out of the
printer.
2. Insert the rear tractor cover and make sure that the interlock connector
is correctly inserted. If the cover is not inserted, the printer is blocked.
A78408739-002
71
Options
Automatic Sheet Feeder
The Automatic Sheet Feeder (ASF), located in the rear of the printer,
provides fast and automatic single sheet and envelopes loading. The ASF
includes:
•
A paper stacker, which automatically collects the output paper.
•
A single bin for single sheets (A5, A4, Letter, Legal. Executive) and
envelopes.
•
A 2nd and 3rd optional bins are also available.
Please find the installation instructions for the ASF on the corresponding
manual. The following picture shows the ASF options and their position in
the printer.
72
A78408739-002
Options
Color Kit
This printer can print not only in
black but also in different colors. For
color printing you need the optional
color kit shown in the figure below.
The color kit is installable by an
authorized technician.
The color or the black ribbon
‘Long Life’ cartridge (20 million
characters) can be used when the
color kit is installed.
Pedestals
Two printer floor pedestals are available:
Three Levels Floor Pedestal for large
paper quantity and dual fanfold
handling.
Two Levels Floor Pedestal with inclinable printer level for document on
demand application
A78408739-002
73
Options
The Cutter
The cutter option allows to cut the paper automatically.
Installing the Cutter
The printer must be turned off while installing the cutter option. If
you install the cutter option while the printer is powered on, the
printer may be damaged.
1.
Remove the ASF cover, the rear tractor area cover and the two small
tractor fixing area covers.
R e ar tracto r
a rea cover
A S F a rea cove r
Tra ctor fixin g
a rea s co vers
2.
74
Keep the covers in a safe place, as they must be reinstalled if the rear
tractor is removed.
Replace the ASF cover.
A78408739-002
Options
3.
Hook the cutter onto the lower pins (1) on both sides inside the tractor
fixing areas, and make sure that the connector (2) is correctly inserted.
(2)
(1)
4.
Lower the cutter so that it lays down on the printer.
A78408739-002
75
Options
5.
Hook the paper grid onto the cutter screws on both sides as shown in
figure.
76
A78408739-002
Printer Specifications
Printer Specifications
Printing Characteristics
Print Head
Matrix
Print Head Life
24 pins - 0.3 mm
900 mil characters (draft)
Print Speed (cps)
10 cpi
Draft
Draft
High Speed Draft
400
700
LQ
NLQ
133
266
430
530
LQ
NLQ
220
300
Quality
High Speed LQ
High Speed NLQ
200
400
Throughput (pages/hour)
ECMA 132
10 cpi
Draft
Draft
High Speed Draft
Quality
High Speed LQ 290
High Speed NLQ 430
Print Matrix (horizontal x vertical)
Draft
12 x 12
10 x 12
8 x 8
12 x 12
12 x 12
8 x 8
10 cpi
12 cpi
15 cpi
17.1 cpi
20 cpi
24 cpi
Quality
36 x 24
30 x 24
24 x 16
36 x 24
30 x 24
24 x 16
Print Density (characters per inch)
Normal
Enlarged
Proportional
10 - 12 - 15 - 17.1 - 20 - 24
5 - 6 - 7.5 - 8.5
Line length (number of characters)
10 cpi
12 cpi
15 cpi
136
163
204
17.1 cpi
20 cpi
24 cpi
233
272
326
Vertical Spacing
6, 8, 12 LPP
3, 4, 6, 8, 12 lines/30 mm
n/60, n/72, n/180, n/216, n/360 inch
Print Styles
Draft - Courier- OCR B - Gothic - Script - OCR A
Print Attributes
Sub-superscript, Underline, Overscore, Italics, Emphasized
Graphic Resolution (dots per inch)
horizontal
vertical
A78408739-002
60, 80, 90, 120, 180, 240, 360
60, 72, 180
77
Printer Specifications
Characters Sets
International character sets ASCII
Standard PC IBM Character CS1 and CS2
Sets
EPSON National Variations
USA, France, Germany, United Kingdom, Denmark-1, Sweden,
Italy, Spain-1, Japan, Norway, Denmark-2, Spain-2, Latin America
IBM and EPSON Character USA (CP437), Greek (CP437-G), Multilingual (CP850), Greek
Sets
(CP851), 96 Greek, Eastern Europe (CP852), Turkish (CP 853),
Cyrillic (CP855), Turkish (CP857), Euro PC Multilingual (CP858),
Portugal (CP860), Hebrew (CP862), Canada/France (CP863),
Arabic (CP864), Denmark/Norway (CP865), Russian (CP866),
Turkish2 (CP867), OCR-A (CP876), OCRB (CP877), GOST, TASS
ISO Character Sets
8859/1 (Latin1), 8859/2 (Latin2), 8859/3 (Latin3), 8859/4 (Latin4),
8859/5 (Latin/Cyrillic), 8859/6 (Latin/Arabic), 8859/7 (Latin/Greek),
8859/8 (Latin/Hebrew), 8859/9 (Latin5). 8859/15 (Latin9)
Paper Handling
9078 plus model Base Configuration
Fanfold Paper
1
LOWER PUSH TRACTOR
Fanfold width:
76 to 432 mm
Copies:
1 original + 7 copies
Cut Sheets (loaded through the manual slot)
Sheet width:
114 to 432 mm
Standard formats:
A5 - A4 -A3- A2 in portrait
Letter - Legal - Executive
Copies:
1 original + 7 copies
(3 to 17 inches)
Max. thickness 0,635 mm
(4,5 to 17 inches)
Max. thickness 0,635 mm
9078D plus model Base Configuration
Fanfold Paper
1
1
LOWER PUSH TRACTOR
Fanfold width:
76 to 432 mm
Copies:
1 original + 7 copies
UPPER PUSH TRACTOR
Fanfold width:
76 to 432 mm
Copies:
1 original + 7 copies
(3 to 17 inches)
Max. thickness 0, 635 mm
(3 to 17 inches)
Max. thickness 0, 635 mm
With the pull tractor option
Push-Pull Feeding
Front fanfold insertion with lower tractor in front push mode and rear tractor in pull mode.
Automatic Sheet Feeder Option
First tray
Single sheets, envelopes and postcards
Second and third tray
Single Sheets
Paper stacker
- Tray capacity
120 sheets (80 g/m2)
- Sheet width
8,89 to 30,48 cm (3,5 to 12 inches)
Copies
1 original + 2 copies
Coexisting with manual sheet (9078 plus model only)
Coexisting with fanfold in push mode
78
A78408739-002
Printer Specifications
BarCodes
UPC-A, UPC-E, EAN-8, EAN-13, UPC-EAN 2, UPC-EAN 5, Code GP, MSI, Code BCD, 2/5-3 BAR,
Code 39, Code 128, Code 11, Code 93, 2/5 Bidirectional, 2/5 Interleaved, 2/5 Industrial, 2/5 Matrix,
POSTNET
Emulations
- EPSON LQ 1050
- EPSON LQ 2550
- IBM Proprinter XL24e
- IBM Proprinter XL24 AGM
- IBM Personal Printer 2391
Standard Functions
•
•
•
•
•
•
•
Automatic print head gap adjustment (AGA)
Automatic paper path switching via operator panel or S/W commands
Paper parking
Plug & Play capability
Bar Code printing
Automatic fanfold positioning for tear-off
Setting and storage of paper format and print conditions for each paper path in the non volatile
memory
Physical and Electrical Characteristics
Interfaces
Parallel
Centronics Compatible Bi-directional (IEEE-1284) nibble and byte modes
- 36 pin Amphenol connector
Receive Buffer: max. 64 Kbytes
Serial
RS-232/C and RS-422/A - dB 25 connector
Baud Rate: 300 to 38400 bps
Automatic interface switching
Reliability
MTBF
MTTR
Workload
Mean Time between failure: 10000 hours at 25% DC
Mean Time To Repair: 30 minutes
43000 pages/month (ECMA 132 - 4 hours for 20 days)
Power Supply
120 V/ 60 Hz
220 - 240 V / 50 Hz
Power Consumption
USA power cable
European power cable
UK power cable
Standby: 28W ---- Average Printing: 90 W
Noise Level
53 dBA
A78408739-002
79
Printer Specifications
Environment Conditions
Storage Conditions
Temperature
Relative Humidity
-40° to 50° C
10%t o 90% RH (non condensing)
Temperature
Relative Humidity
10° to 38° C
10 % to 90 % RH (non condensing)
Temperature
Relative Humidity
16° to 24° C
40% to 60% RH (non condensing)
Operating Conditions
Paper Conditions
Physical dimensions
Height
Width
Depth
Weight
310 mm (12,21 inches)
665 mm (26,18 inches)
390 mm (15,35 inches)
18 kg (39,7 lbs)
Consumables and Options
•
•
•
•
•
•
•
•
•
•
80
Black ribbon cartridge (15 million characters)
Black ribbon “Long Life” cartridge (20 million characters)
Color ribbon cartridge (2 million characters for each band)
Automatic Sheet Feeder (ASF) with envelopes and sheet stacker
Two additional trays for the automatic sheet feeder
Additional pull tractor unit for push-pull fanfold handling
Color Kit
Three level floor pedestal for high paper capacity and dual fanfold
Two level floor pedestal with inclinable printer level
Cutter option
A78408739-002