Download Read First
Transcript
Microsoft OS User Manual ENGLISH Introduction Read First This Digital Photo Viewer is a stand-alone device that is designed to transfer and store images from a PC and then display the images. Using the application software supplied with this device, you can organize,edit, enhance and download the image in your PC to this device using USB. Quick Installation Guide SYSTEM REQUIREMENTS: Windows 98 / 2000 / ME / XP / Vista INSTALLATION PROCEDURE: NOTE: The software cannot initialize when the device is plugged in and running slide show. means described in these operating instructions. All other servicing should be referred to qualified service personnel. . Important Safety Instructions ** Important: Install application software before connect device to PC. ** 1. Disconnect device USB cable from PC if it is connected. 2. Insert CD and follow the on-screen instruction to install “Photo Viewer”. 3. After the application software has been successfully installed, you could connect device to PC with the provided USB cable. 4. Windows OS will set up hardware driver automatically. 5. Launch “Photo Viewer” and enjoy. The device should be away from sources of high heat such as radiators or stoves. The device should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. Care should be taken so that objects are not placed on, nor liquids spilled on or inside the device. . should not attempt to service the device beyond those The user WARNING: This device will be fully charged after two hours. Do not leave the device connected to the USB for longer than 12 consecutive hours otherwise damage and overheating of the device may occur. Do not expose this device to water or moisture. Do not remove cover. No user serviceable parts inside. Refer servicing to qualified personnel. 2. The application Photo Viewer will be installed on your computer and a shortcut to the application will appear on your desktop. DO NOT LAUNCH THE SOFTWARE YET. 3. After the software is installed, connect the device to the computer with the USB cable supplied. The hardware drivers will be installed automatically. Follow the on-screen instructions and accept the installation screens that appear. 4. After hardware installation is complete, launch the PhotoViewer application from the shortcut on your PC desktop. NOTE: If you are unable to launch the software or connect to your Photo Viewer, go to the Troubleshooting of this manual for more information. Installing the Software / Hardware IMPORTANT: You must install the software to your computer before connecting the device to your computer for the first time. Charging the Battery The internal battery of the device may be charged using the USB cable when connected to a powered USB port(such as USB port on your computer) or hub.It will be fully charged after two hours. At full charge, the device can provide up to 3 hours of run time. 1. Insert the CD-ROM and run the file SETUP_UT1.02.EXE; Follow the onscreen instructions. USB on computer Using the Photo Viewer Software Editing Images Mini B on Photo Viewer 1. Select an Image to Edit 1. Connect to PC Use the USB cable provided. Connect the large end to the computer and the small end to the device. Crop Photo USB Cable Double-click the Photo Viewer shortcut on your desktop. To delete a photo: select the photo and click " To delete all photos: click " 3. View Photos Stored in the Photo Viewer To view the photos: click " " To delete a photo : select the photo and click " To delete all photos: click " " 2. Edit Image 6. Organize Collection Panel 2. Launch the Photo Viewer Software To change the order of the photo, select the photo then click " to move to the back and click " " In the Edit Image Window you can do the following: " " " " to move to the front. 7. Save and Restore Collection Panel 4. Browse Images on Your PC To save the photos on the Collection Panel to your PC, click " Use the File Manager to browse photos on your PC. NOTE: The device reads JPG/ BMP/ TIF/ GIF/ PNG images. To retrieve the the saved Collection Panel, click " 8. Download Collection Panel to Digital Photo Viewer 5. Select Images and Transfer to Collection Panel The Image Preview area will display a thumbnail preview of all of the JPG/ BMP/ TIF/ GIF/ PNG images that are located in the directory you have selected. Select the thumbnail image and click to transfer the image as-is. Select the thumbnail image and click to edit the image before transferring (see Editing Images). Arrange Sequence Click " Transfer collection to Device Crop Photo Important !! Do not disconnect the device until the download process is complete and you have exited successfully from the Photo Viewer program. Deleting single photo Turn off the slide show, select the photo you want to delete, press and hold UP until “ DELETE” appears on the screen, and press MODE to delete. Corrosion, oxidation, battery-leakage and any other gradually acidic defect of this nature will invalidate the guarantee. Using the Photo Viewer Turning power on/off To turn on power, press and hold MODE/ until the screen turns on. To turn off power, you must turn off the slide show first, then press and hold MODE until the screen turns off. Manual viewing of photos Upon powering up, the device is in browse mode, or manual viewing mode, press to view the next photo, and press to view the previous photo. NOTE: In browse viewing mode, the screen turns off automatically when there is no key pressed in two minutes. Corrosion, oxidation, battery-leakage and any other gradually acidic defect of this nature will invalidate the guarantee. " to download all images on the collection panel to NOTE: Images that are brighter and more contrast will look better on the smaller monitor of the device. Rotate: Use to rotate the image clockwise or counterclockwise. Digital Photo Viewer. View Photos Using the Function Keys 1. Monitor 2. Power / Play & Pause 3. Previous Image / Delete images 4. Next Image / Delete all Images. 5. Mini USB Connection " ". Crop: click and drag the smaller boxes (at the corners of the large box)to increase or decrease the area to be cropped. Reposition: click and drag in the center of the large box to change the position of the crop. Brightness / Contrast: click and drag the slider bars. Slide show Press MODE to change to slide show from browse mode, the screen displays “Auto Play On”. Toturn off slide show,press MODE again and the screen displays “Auto Play Off”. Deleting all photos Turn off the slide show, press and hold DOWN until “ DELETE ALL ” appears on the screen, press MODE to delete. Troubleshooting for lnstallation If the device displays error message “Device not connected” during installation, follow these steps to resolve: A.For Software issues (Photo Viewer software can not launch) 1. Re-insert and launch the installation CD and choose “Remove” or “Uninstall” from the Installer Menu. 2. Disconnect the USB cable and device from the computer and restart. 3. After computer has restarted, launch the installer again and reinstall the software. NOTE: DO NOT connect the USB cable until after the software is installed. B.For Hardware installation issues (Device not recognized) 1. With the Viewer connected to the computer via USB go to the 3.Click DONE The edited image will be added to the collection panel. Start Menu/ Control Panels/ Add Hardware. 2. When the Dialog box comes up, click the option that says “Yes, I have already connected the hardware”. 3. In the list of Devices-Find “Photo Viewer” click NEXT and this will give the status of the device. If a warning icon appears next to the Photo Viewer then double click the icon and select the option to “Reinstall the software”. Power consumption 0.25W Disposal of Used Electrical & Electronic Equipment The meaning of the symbol on the product, its accessory or packaging indicates that this product shall not be treated as household waste. Please, dispose of this equipment at your applicable collection point for the recycling of electrical & electronic equipments waste. In the European Union and Other European countries which there are separate collection systems for used electrical and electronic product. By ensuring the correct disposal of this product, you will help prevent potentially hazardous to the environment and to human health, which could otherwise be caused by unsuitable waste handling of this product. The recycling of materials will help conserve natural resources. Please do not therefore dispose of your old electrical and electronic equipment with your household waste. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. For more information and warranty conditions, please visit : www.akai.eu Mac OS User Manual ENGLISH The device should be away from sources of high heat such as radiators or stoves. The device should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. Care should be taken so that objects are not placed on, nor liquids spilled on or inside the device. . should not attempt to service the device beyond those The user Introduction Read First This Digital Photo Viewer is a stand-alone device that is designed to transfer and store images from a PC and then display the images. Using the application software supplied with this device, you can organize,edit, enhance and download the image in your PC to this device using USB. Quick Installation Guide SYSTEM REQUIREMENTS: Mac OS 10.4 INSTALLATION PROCEDURE: ** Important: Install application software before connect device to PC. ** 1. Disconnect device USB cable from PC if it is connected. 2. Insert CD and follow the on-screen instruction to install “Photo Viewer”. 3. After the application software has been successfully installed, you could connect device to PC with the provided USB cable. 4. Mac OS will set up hardware driver automatically. 5. Launch “Photo Viewer” and enjoy. NOTE: The software cannot initialize when the device is plugged in and running slide show. Using the Photo Viewer Software means described in these operating instructions. All other servicing should be referred to qualified service personnel. . Important Safety Instructions NOTE: If you are unable to launch the software or connect to your Photo Viewer, go to the Troubleshooting of this manual for more information. Installing the Software / Hardware WARNING: This device will be fully charged after two hours. Do not leave the device connected to the USB for longer than 12 consecutive hours otherwise damage and overheating of the device may occur. Do not expose this device to water or moisture. Do not remove cover. No user serviceable parts inside. Refer servicing to qualified personnel. 2. The application Photo Viewer will be installed on your computer and a shortcut to the application will appear on your desktop. DO NOT LAUNCH THE SOFTWARE YET. 3. After the software is installed, connect the device to the computer with the USB cable supplied. The hardware drivers will be installed automatically. Follow the on-screen instructions and accept the installation screens that appear. 4. After hardware installation is complete, launch the PhotoViewer application from the shortcut on your PC desktop. IMPORTANT: You must install the software to your computer before connecting the device to your computer for the first time. 1. Insert the CD-ROM and run the file Photo Viewer Mac OS.dmg; Follow the onscreen instructions. Charging the Battery The internal battery of the device may be charged using the USB cable when connected to a powered USB port(such as USB port on your computer) or hub.It will be fully charged after two hours. At full charge, the device can provide up to 3 hours of run time. Editing Images USB on computer 1. Select an Image to Edit Mini B on Photo Viewer 1. Connect to Mac Use the USB cable provided. Connect the large end to the computer and the small end to the device. Crop Photo USB Cable 2. Edit Image 2. Launch the Photo Viewer Software Double-click the Photo Viewer shortcut on your desktop. 6. Organize Collection Panel 3. View Photos Stored in the Photo Viewer To view the photos: click " To delete a photo : select the photo and click " To delete all photos: click " To delete a photo: select the photo and click " " To delete all photos: click " " " " " 7. Save and Restore Collection Panel To save the photos on the Collection Panel to your PC, click " 4. Browse Images on Your PC To retrieve the the saved Collection Panel, click " Use the File Manager to browse photos on your PC. NOTE: The device reads JPG/ BMP/ TIF/ GIF/ PNG images. 8. Download Collection Panel to Digital Photo Viewer 5. Select Images and Transfer to Collection Panel Click " The Image Preview area will display a thumbnail preview of all of the JPG/ BMP/ TIF/ GIF/ PNG images that are located in the directory you have selected. Select the thumbnail image and click to transfer the image as-is. Select the thumbnail image and click to edit the image before transferring (see Editing Images). NOTE: Images that are brighter and more contrast will look better on the smaller monitor of the device. Rotate: Use Important !! Do not disconnect the device until the download process is complete and you have exited successfully from the Photo Viewer program. Deleting single photo Turn off the slide show, select the photo you want to delete, press and hold UP until “ DELETE” appears on the screen, and press MODE to delete. Corrosion, oxidation, battery-leakage and any other gradually acidic defect of this nature will invalidate the guarantee. Using the Photo Viewer Turning power on/off To turn on power, press and hold MODE/ until the screen turns on. To turn off power, you must turn off the slide show first, then press and hold MODE until the screen turns off. Manual viewing of photos Upon powering up, the device is in browse mode, or manual viewing mode, press to view the next photo, and press to view the previous photo. NOTE: In browse viewing mode, the screen turns off automatically when there is no key pressed in two minutes. Corrosion, oxidation, battery-leakage and any other gradually acidic defect of this nature will invalidate the guarantee. " to download all images on the collection panel to Digital Photo Viewer. Using the Function Keys 1. Monitor 2. Power / Play & Pause 3. Previous Image / Delete images 4. Next Image / Delete all Images. 5. Mini USB Connection " ". In the Edit Image Window you can do the following: Crop: click and drag the smaller boxes (at the corners of the large box)to increase or decrease the area to be cropped. Reposition: click and drag in the center of the large box to change the position of the crop. Brightness / Contrast: click and drag the slider bars. Slide show Press MODE to change to slide show from browse mode, the screen displays “Auto Play On”. Toturn off slide show,press MODE again and the screen displays “Auto Play Off”. Deleting all photos Turn off the slide show, press and hold DOWN until “ DELETE ALL ” appears on the screen, press MODE to delete. Troubleshooting for lnstallation If the device displays error message “Device not connected” during installation, follow these steps to resolve: A.For Software issues (Photo Viewer software can not launch) 1. Re-insert and launch the installation CD and choose “Remove” or “Uninstall” from the Installer Menu. 2. Disconnect the USB cable and device from the computer and restart. 3. After computer has restarted, launch the installer again and reinstall the software. NOTE: DO NOT connect the USB cable until after the software is installed. B.For Hardware installation issues (Device not recognized) 1. With the Viewer connected to the computer via USB go to the to rotate the image clockwise or counterclockwise. 3.Click DONE The edited image will be added to the collection panel. Start Menu/ Control Panels/ Add Hardware. 2. When the Dialog box comes up, click the option that says “Yes, I have already connected the hardware”. 3. In the list of Devices-Find “Photo Viewer” click NEXT and this will give the status of the device. If a warning icon appears next to the Photo Viewer then double click the icon and select the option to “Reinstall the software”. Power consumption 0.25W Disposal of Used Electrical & Electronic Equipment The meaning of the symbol on the product, its accessory or packaging indicates that this product shall not be treated as household waste. Please, dispose of this equipment at your applicable collection point for the recycling of electrical & electronic equipments waste. In the European Union and Other European countries which there are separate collection systems for used electrical and electronic product. By ensuring the correct disposal of this product, you will help prevent potentially hazardous to the environment and to human health, which could otherwise be caused by unsuitable waste handling of this product. The recycling of materials will help conserve natural resources. Please do not therefore dispose of your old electrical and electronic equipment with your household waste. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. For more information and warranty conditions, please visit : www.akai.eu