1
Download Support Overview Installation
Transcript
A Beijer Electronics Group Company JetNet 4508i/4508if Series Industrial Ethernet Managed Switch Quick Installation Guide V1.0 Overview 2. Tighten the wire-clamp screws to prevent the power wires from being loosened. Give a name to the new console connection. Notes: The recommended typical operating voltage is DC 24V (Input range: DC12~ 36 Choose the COM name and select the correct serial settings. The serial port settings of V), maximum power consumption is 15 Watts. JetNet 4508 are as below: 9600bps, No parity check, 8 Data bits, 1 stop bit Wiring the Relay Output (DO) After connected, you will see the Switch login request. Type the username and password and then you can login. The default username is “admin”, password is “admin”. The relay output contacts are in Follow the manual to configure the software features. the bottom side as shown on 2. Preparation for Web management: Before you attempt to use the embedded web Figure-3. The relay output (DO) The JetNet 4508i/JetNet 4508if are new generation industrial managed Fast Ethernet Switch with advanced layer-2 management features and isolated system design for the power distribution or power feeding application. interface to manage switch operation, verify that JetNet 4508i/4508if is properly installed is controlled by the pre-defined on your network and that every PC on this network can access the switch via the web operating rules. To activate relay browser. output function, please refer to The JetNet 4508i/4508if series offer 6-port Fast Ethernet RJ-45 connectors plus 2-port Fast Ethernet Fiber interfaces – JetNet 4508if, or 8-port Fast Ethernet RJ-45 connectors – JetNet 4508i. Both of models adopted 32Gbps High performance Ethernet Switch Fabric to ensure real-time and high quality connectivity in various networking application, and the isolated system design fulfilled a very high level EMC inquire for the Substation application and the User’s Manual for the Relay Type http://4508_IP_Address (The default IP address is Figure-3 192.168.10.1.), then press Enter. Output information. Note: The relay contactors only supports 1A current, DC 24V. It is not recommended to apply voltage and current higher than the specifications. The login screen will appear next. Type in the user name and password and click “OK” button. The welcome page of the Web-Based management compliance with IEC 61850-3 and IEEE 1613 as well. The Switches also supports IP31 Wiring the Digital Input (DI) enclosure protection and 2 operating temperature models- normal temperature for general The Digital Input (D.I.) contacts password is admin/admin. purpose -25~70°C (JetNet4508i), -10~70°C (JetNet 4508if ) and wide operating temperature are in the bottom side of the At the left column of the web for rugged environment -40~75°C (JetNet 4508i-w/ JetNet 4508if-w). device as shown in Figure-4. management interface are the software This quick installation guide introduces the system powering, device installation and how to It accepts one external DC type features, where ring column will list the connect the Ethernet interface. For more switch configuration, please download the JetNet signal available settings. 4508 series user manual from Korenix Website. configured to send alert message input and can interface will appear then. The default user name and be through Ethernet when the signal For more operating instructions, please refer to the User’s manual of JetNet 4508i/JetNet 4508if V2 series included in the packing Figure-4 is changed. Package Check List JetNet 4508i or JetNet 4508if or downloadable from the Korenix Website – www.korenix.com. Note: the DI accepts DC type signal and supports isolated input circuit with Digital A Beijer Electronics Group Company JetNet 4508i/4508if Series Industrial Ethernet Managed Switch Quick Installation Guide V1.0 Overview Support High Level input DC 11V~30V and Digital Low Level input DC 0V~10V. Do not apply voltage higher than the specification; it may cause internal circuit damage or a wrong 5 Years Warranty action of DI. Each of Korenix’s product line is designed, produced, and tested with high industrial Connecting to Network standard. Korenix warrants that the Product(s) shall be free from defects in materials and Installation 1. Connecting the Ethernet Port: Connect the Ethernet port of JetNet 4508i/JetNet 4508if workmanship for a period of five (5) years from the date of delivery provided that the series with the other Ethernet device by Cat-5/Cat-6 UTP or STP cable, and then the Product was properly installed and used. Mount the unit LNK/ACT LED will turn on and start flashing to indicate the communication is occurred This warranty is voided if defects, malfunctions or failures of the warranted Product are Din-Rail mount: Mount the din-rail clip on the rear of JetNet between 2 devices. caused by damage resulting from force measure (such as floods, fire, etc.), other external 4508i/4508if on the DIN rail. For information about the DIN Rail 2. Connecting the Fiber Port: Cross-connect the transmit channel at each end to the receive forces such as power disturbances, over spec power input, or incorrect cabling; or the installation, please refer to user’s manual. channel at the opposite end as illustrated in the Figure-5 (JetNet 4508if series). warranted Product is misused, abused, or operated, altered and repaired in an unauthorized The JetNet 4508i/JetNet 4508if are new generation industrial managed Fast Ethernet Switch with advanced layer-2 management features and isolated system design for the power distribution or power feeding application. with DIN Rail kit x1 The JetNet 4508i/4508if series offer 6-port Fast Ethernet RJ-45 connectors plus 2-port Fast Ethernet Fiber interfaces – JetNet 4508if, or 8-port Fast Ethernet RJ-45 connectors – JetNet 4508i. Both of models adopted 32Gbps High performance Ethernet Switch Fabric to ensure real-time and high quality connectivity in various networking application, and the isolated system design fulfilled a very high level EMC inquire for the Substation application and Quick Installation Guide Console Cable (RJ-45 /DB9) Grounding JetNet Switch compliance with IEC 61850-3 and IEEE 1613 as well. The Switches also supports IP31 enclosure protection and 2 operating temperature models- normal temperature for general purpose -25~70°C (JetNet4508i), -10~70°C (JetNet 4508if ) and wide operating temperature for rugged environment -40~75°C (JetNet 4508i-w/ JetNet 4508if-w). This quick installation guide introduces the system powering, device installation and how to connect the Ethernet interface. For more switch configuration, please download the JetNet 4508 series user manual from Korenix Website. or improper way. TX TX ATTENTION Attention! To avoid system damage caused by sparks, please DO NOT plug in power This is a Class 1 Laser/LED product. There is one grounding screw on the bottom Ǽ side of JetNet 4508i/4508if. Connect the frame connector when power is on. Don't look into the Laser/LED Beam. grounding of JetNet 4508i/4508if to the A RX RX B The product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European grounding surface to ensure safety and prevent Device Management Parliament and of the Council of 27 January 2003 on the restriction of the use of certain noise to interfere communication. JetNet 4508i/JetNet 4508if series provide both in-band and out-band configuration methods, Wiring the Power Inputs and adopted same software as JetNet 4508/4508f series. You can configure the switch via the Korenix Customer Service 1. Insert the positive and negative wires into the V+ and Vcontact on the terminal block connector. RS-232 console with the attached console cable or you can remotely manage the switch via network. You can choose Telnet/SSH, Web/HTTPS management. 1. Preparation for console management: Attach the RS-232 DB9 connector to your PC’s COM port. Connect the RJ-45 connector to the console port of the JetNet 4508i/4508if Switch. Go to Start -> Program -> Accessories -> Communication -> Hyper Terminal hazardous substances in electrical and electronics equipment(RoHS Directives & RoHS 2.0) KoreCARE is Korenix Technology's global service center, where our professional staffs are ready to solve your problems at any time Korenix global service center's e-mail is [email protected]. For more information and documents download please visit our website: http://www.korenix.com/downloads.htm 溿宋䔏㈞⏴ḡ“admin”Ə⮭䟨ḡ“admin”˛ ㋰䅎㈲ⅳ忂堳愴何彖ờ⊆僤˛ ⪺墾 2. Web䩟䋄₄⟅濣✏ὦ䔏ⴳ⅌䙫Web䔳杉㝌䮈䏭ẋ㍉㜡㒴ὃ∴Ə寞橳宨JetNet 4508i JetNet4508i/JetNet4508if㘖㖗ᷧỊⷌḁ䮈䏭❲⿒怆Ọ⤑伸ẋ㍉㜡⅞㛰ℯ忂䙫ṳⰩ䮈䏭 / 4508ifⷙ㭊䡕⭰墬✏わ䙫伸仃ᷱƏ⹝᷻忀䦴伸仃ᷱ䙫㮶ᷧ⏗PC⏖Ọ态微Web㴶妯 ⊆僤⑳䋓䪲䙫䳢仆宥守ᾂ愴䔜⑳ᾂ䔜䙫䔏˛JetNet4508i/4508if䳢⇾㎷ᾂ6䫖⏊⿒怆 ♏宦旕ẋ㍉㜡˛ Ọ⤑伸RJ-45㎌⏊Ọ⎱2䫖⏊⿒怆Ọ⤑伸ℰ事㎌⏊ - JetNet4508ifƏㇽ8䫖⏊⿒怆Ọ⤑伸 ␖⊏PCᷱ䙫伸桜㴶妯♏ƋInternet ExplorerㇽMozilla Firefox㴶妯♏ƌ˛ RJ-45必㎌♏ - JetNet4508i˛忀ḋ䦴㜡❲憮䔏32Gbps䙫檿『僤Ọ⤑伸ẋ㍉䟐昜ƏỌ䡕 彺⅌http://4508_IP_Address (溿宋IP ✗✧㘖 192.168.10.1.), 䄝⏵㋰Enter攕˛ ῄ✏⏫䦴伸仃䔏䧲䙫⮅㗝『⑳檿⒨崏䙫必㎌Ə䋓䪲䳢仆宥守⮅䎗ṭ⯠⇭䫀䔏 ㎌䜧✏䙢⼼ⰶ⸼ᷱἁ⇡䎗˛ Figure-3 檿㰛⹚䙫䔜䢨Ⅳ⮠『奨㰩Ə⹝䬍⏯IEC61850-3⑳IEEE 1613㟮↭˛富ẋ㍉㜡徿㔖㋨ 彺⅌䔏㈞⏴⑳⮭䟨Ə䂠⇢ “OK” 攕˛䄝⏵㘥䤡⟡ṵ IP31昙㊋䬰于⑳2䦴㒴ὃ㸐⺍㨈❲ - ⸟㸐ᷲᷧ刓䔏䔏-25˵70濎ƋJetNet 4508iƌƏ 㮦⿍: 䶥䏳┦㉣墤┦ᶃ㏭ㆿDC24V 1AƲ㉦刎ⵒ䏦䕂䏳≉⍊䏳㯿榖ᵌ墂㛺 -10˵70°CƋJetNet4508ifƌ⑳⮤ⷌὃ㸐⺍そ⊊䙫䎖⡪-40˵75° CƋJetNet4508i-W/ Jet 㐮⨕悍幑‣㉣䵽(DI) Net4508if-Wƌ˛ 㕗⬾彺⅌ƋDIƌ䙫㎌姍㘖✏ẋ㍉㜡䙫ᾎƏ⥩⛥Figure-4. 㜓⿒怆⭰墬㋮⌾Ẳ亴ṭ䳢仆ᾂ䔜Ə宥⣮⭰墬ƏỌ⎱⥩Ἴ必㎌Ọ⤑伸㎌⏊˛㬙ṭ姊㛛 ⭪㎌⎾ᷧḑ⣽惏DCῈ⏞彺⅌Ə⹝᷻⏖Ọ态微愴何䔏Ọ⤑伸⎸忨孍㊌㵯ざ⼺㊌孍墒 ⤁䙫ẋ㍉㜡愴何Ə寞ẵKorenix伸䫀ᷲ彤JetNet4508䳢⇾䔏㈞㈲ⅳ˛ 㾧⎸˛ Web䙫䮈䏭䔳杉䙫㬉徵桜杉˛溿宋䙫䔏㈞⏴⑳⮭䟨㘖 admin/admin˛ JetNet4508i/ JetNet4508if v2䳢⇾Ẏ⒨ A Beijer Electronics Group Company JetNet 4508i/4508if Series Industrial Ethernet Managed Switch Quick Installation Guide V1.0 䙫䔏㈞㈲ⅳƏ⏖ẵKorenix伸䫀ᷲ彤 - Overview The JetNet 4508i/JetNet 4508if are new generation industrial managed Fast Ethernet Switch with advanced layer-2 management features and isolated system design for the power ⸍㛰DIN ⯣彏⤾ờ x1 distribution or power feeding application. The JetNet 4508i/4508if series offer 6-port Fast Ethernet RJ-45 connectors plus 2-port Fast Ethernet Fiber interfaces – JetNet 4508if, or 8-port Fast Ethernet RJ-45 connectors – JetNet 4508i. Both of models adopted 32Gbps High performance Ethernet Switch Fabric to ensure real-time and high quality connectivity in various networking application, and the isolated www.korenix.com.cn˛ system design fulfilled a very high level EMC inquire for the Substation application and compliance with IEC 61850-3 and IEEE 1613 as well. The Switches also supports IP31 ⿒怆⭰墬㈲ⅳ Ə⅝Ḕ䎖⇾⯭伾⇾⇡⏖䔏䙫宥何˛ 㛰⅚寍亭䙫㒴ὃ寛㗵Ə寞⎩俪 ᵥ⍿㳃∓ JetNet 4508i or JetNet 4508if ✏Web䮈䏭䔳杉䙫ⷍᾎ㟶㘖彖ờ⊆僤 enclosure protection and 2 operating temperature models- normal temperature for general purpose -25~70°C (JetNet4508i), -10~70°C (JetNet 4508if ) and wide operating temperature for rugged environment -40~75°C (JetNet 4508i-w/ JetNet 4508if-w). This quick installation guide introduces the system powering, device installation and how to connect the Ethernet interface. For more switch configuration, please download the JetNet 4508 series user manual from Korenix Website. ㎎∝䔜仭 (RJ-45 /DB9) ⩠ヵ㗋⅟ ⩇垃 5ⴲ實ẛ Figure-4 ⩇垃 㮦⿍:㐮⨕悍幑‣㽷㉣⊕DC♉ẟ⊵ⴴ㏭ㆿ䏦㐮⨕榖䏳ⴱ幑‣DC11Vnj30V⍊㐮⨕Ḍ ㈧㛰䦸㴂䏭〄Ẏ⒨䙫宥守˚∝怇⎱㴲宼惤㘖憮䔏彪檿䙫ⷌḁ㟮↭˛䦸㴂䏭〄ῄ宨 Din⯣彏⭰墬: ⭰墬✏JetNet4508i/4508if✏DIN⯣彏⏵惏䙫DIN⯣彏⤠ 䏳ⴱ幑‣DC0Vnj10V幑‣䕂敒䡹䏳岭Ʋ堿㑻⅞䏳≉榖ᵌ墂㛺;店⊭侻ᷘ廞ノ⁃徦 凑Ẏ⒨⇡崎㗌嵞㎷ᾂ㛧檿5⹛Ḳℴ崠ῄ㛴⊈Əῄ㜆旛⥩⛇曝ờ㍆✶ㇽ∝䧲ᷴ剖 㛰⅚DIN⯣彏⭰墬䙫ῈざƏ寞⎩俪䔏㈞㈲ⅳ˛ 䏳岭㈝☍ピ㐮⨕悍幑‣㽷䕂媭ⅦḚƲ 俳⯣凛Ẏ⒨㔬暃Əㇸồ⯭㎷ᾂℴ崠仛㛴⊈˛ JetNet 4508i / 4508if㉣◮ 府㉣⃮丏䶚 䄝俳Ə凑䄝⣽⊂䁒˚㰛˚曞䁥㈧怇ㇷ䙫Ẏ⒨㔬暃Əㇽ⅝⭪⣽惏⛇䴇⥩䔜㹷⹙㉗˚ ✏JetNet 4508i/4508if䙫ᾎ㛰ᷧḑ㎌✗垡 1. 府㉣ᶣ⟨丏䦭⊡: 态微Cat-5/ CAT-6 UTPㇽSTP䔜仭必㎌JetNet4508i/ JetNet4508if䳢 ᷴ⼺䔜㹷彺⅌˚ᷴ⼺㎌亦䬰怇ㇷ䙫㍆✶Əᷴ⇾⅌Ẏ⒨ῄ⛡勪⛛ƞ㭋⣽ƏẎ⒨墒寖 Ḅ˛⯭JetNet4508i/4508if䙫⣽⣚㎌✗Ọῄ宨 ⇾∗⅝ẽ伸仃宥⣮Ə䄝⏵LNK/ ACT㋮䤡䁖⯭ẕ嵞⹝⻧⦲旑䂨Ə塏㗵ḋḑ宥⣮Ḳ旛 䔏˚㜑亶㍯㜪䙫䏭⎱㔠䬰堳ḡ⯭怇ㇷῄ⛡㝈㬥⤘㔯˛ ⭰⅏⑳昙㭉♑⣗⹙㉗态宖˛ 态Ὲㇷ⊆˛ 㮦⿍媵↽ᵌ䏳㵎ⶾ⋭㒴㊐㆒㉣䵽䦭⨎濕ᶣ弽ᵥ䏝㼩兯廞ノ䮹䶝㈝☍Ʋ 䏳㵎㉣䵽 2. 府㉣ 䵢䦭⊡:ẋ⎰必㎌ἇ彺Ὲ怺∗䛟㎌⎾Ὲ怺Ə䛟⎴Ṇᷧ㠞˛⥩⛥㈧䤡(JetNet 㭋Ẏ⒨ῄ宨⭳⅏䬍⏯㬎䛆2003⹛1㛯27㗌䔜㯻⑳䔜⬷宥⣮⍘⮚䉐崏昷∝⦻ἁ㈧㎷ 1. 㭊㝨⑳崆㝨⇭−㎌⅌䫖⬷㍹ᷱ䙫V+ ⑳V- ㎌䂠˛ 4508if series)˛ ⇡䙫昷䔏㋮ị2002/95/EC(ROHS䥨ị)⎱2011/65/EU(RoHS 2.0)˛ ATTENTION Ǽ Korenix ⏬⋌㗋⅟ TX TX KoreCARE 㘖䦸㴂䏭〄䦸㉧⅏䏪㛴⊈Ḕ⾪Əㇸồ᷺ḁ䙫㉧㜖ạ晶㗝↭⣮姊䬻わ䙫 This is a Class 1 Laser/LED product. Don't look into the Laser/LED Beam. A RX RX 䕸旕˛䦸㴂䏭〄⅏䏪㛴⊈Ḕ⾪ EMAIL: [email protected] B 婼⟅䩟䋄 JetNet 4508i/JetNet 4508if 䳢⇾㎷ᾂṭ桸⸍Ⅼ⑳桸⸍⣽䙫ḋ䦴愴何㖠㲼Ə⹝⑳JetNet 寍亭寛㗵⎱㕮ờ寞凚伸䫀ᷲ彤: http://www.korenix.com.cn/support_downloads.htm ḁ⊈㛴⊈: [email protected] ⭿伸: www.korenix.com.cn 4508/4508f憮䔏䛟⏳䙫彖ờ˛わ⏖Ọ态微昫⸍䙫䔜仭必㎌RS-232㎎∝䫖⏊愴何ẋ㍉ 㜡ㇽ态微伸仃心䧲䮈䏭ẋ㍉㜡˛わ⏖Ọ忰㋐䙫Telnet/SSHƏTelnet/ HTTPS䮈䏭ẋ㍉ 㜡˛ 2. ㋎䴎亦⤠䙫垡摰ƏỌ昙㭉䔜㹷亦墒㝥⻧˛ 1. ㉥䩟䋄₄⟅: 必㎌RS-232 DB9㎌⤛∗PC䙫COM⏊˛必㎌RJ-45必㎌⤛JetNet 㮦⿍: ㉦刎‶♉䕂ⲣḚ䏳≉DC 24V (䏳≉凁▲: DC12~ 36 V), 㖾⟥侻仕㓭15 Watts 4508i/4508ifẋ㍉㜡㎎∝䫖⏊˛ 䶥䏳┦幑₸㉣䵽(DO) 䂠⇢Start -> Program -> Accessories -> Communication -> Hyper Terminal 从䔜♏彺⇡姍䂠✏ᾎ妨Figure-3˛从䔜♏彺⇡ƋDOƌ㘖态微桫ℯ⮁Ḱ䙫㒴ὃ妫∀ 什㖗䙫㎎∝必㎌⑤⏴˛ 㝌㎎∝˛奨㾧㴢从䔜♏彺⇡⊆僤Ə寞⎩旬䔏㈞㈲ⅳḡ从䔜♏彺⇡䙫Ὲざ˛ 忰㋐COM⏴䧗Ə⹝忰㋐㭊䡕䙫ḙ⏊宥何˛ JetNet4508䙫ḙ堳䫖⏊宥何⥩ᷲƝ 9600bps, No parity check, 8 Data bits, 1 stop bit 必㎌⏵Əἁ䛲∗ẋ㍉㜡䙫䙢⼼寞㰩˛彺⅌䔏㈞⏴⑳⮭䟨Ə䄝⏵Ⱈ⏖Ọ䙢⼼˛ Korenix Technology Co., Ltd. (A Beijer Electronics Group Company) Tel:+886-2-89111000 Fax:+886-2-29123328 Business service:[email protected] Customer service:[email protected] www.korenix.com CPQ000N4508100 Patent No. (Taiwan): Granted Invention: I 313547 Granted Invention: I 321415 Granted Invention: I 344766 Granted Invention: I 346480 Granted Invention: I 356616 Granted Invention: I 364684 Granted Invention: I 376118 Granted Invention: I 393317 Granted Invention: I 398066 Granted Invention: I 398125 Utility Model: M 339841 Utility Model: M 339840
