Transcript
4. Assembling the Probe Stand User's Manual Assembling the Base and Arm Attach the arm screw (the side with one U shaped notch) to the screw hole in the center of the base. Use a wrench or other tool to tightly secure the flat part of the arm screw. Probe Stand Attaching the Probe Head Attach the probe holder to the probe stand. Use a wrench or other tool to hold the flat part of the arm screw in place, then turn the probe holder to fasten. Then, using a wrench, grasp the probe holder’s hexagonal part and tighten. This user’s manual describes handling of the probe stand. To ensure correct use, please read this manual thoroughly before beginning operation. After reading this manual, keep it in a convenient location for quick reference in the event a question arises during operation. Attaching the Probe Holder Assembling the Base and Arm Arm 1 U-shaped notch Base 1st Edition : July 2006 (YK) All Rights Reserved, Copyright © 2006, Yokogawa Electric Corporation Probe holder IM 701919-01E 1st Edition 5. Attaching the Probe Attach the probe to the probe holder. Turn the probe attachment knob to securely attach the probe. Safety Precautions To ensure safe and correct operation of the instrument, you must take the safety precautions given below. The instrument’s protective functions may not work if used in a manner not described in this manual. Yokogawa Electric Corporation assumes no liability for the customer’s failure to comply with these requirements. Conventions Used in This Manual CAUTION Note Calls attention to actions or conditions that could cause light injury to the user or damage to the instrument or user's data, and precautions that can be taken to prevent such occurrences. Calls attention to information that is important for proper operation of the instrument. Take the following precautions. Failure to do so can result in damage to instruments or injury to users. Note Take care not to tighten the probe too tightly. CAUTION • If you loosen the arm lock knob, all three joints will become loose, and may move unless held. Attach the probe tip securely to the circuit under test, and hold the probe with your hand when loosening the arm lock knob so that the probe or circuit under test are not damaged. 6. Positioning the Probe If you loosen the arm lock knob, three joints become free to move. Secure the probe tip just before coming into contact with the circuit under test. Turn the probe positioning knob to touch the probe tip to the circuit under test, then press with the appropriate amount of force. • The stand weighs approximately 1.5 kg. Take care not to drop it on your foot. • When attaching the probe, be careful not to tighten it too tightly. Doing so can damage the probe. 1. Checking the Product Confirm that the model on the name label matches that of your order. MODEL Model 701919 Suffix Code Specification - Probe Stand • Pressing the probe to the circuit under test too strongly can damage the probe or the circuit under test. Adjust the probe positioning knob so that the probe does not press into the circuit under test too strongly. 2. Checking the Contents of the Package After opening the package, check that the following items are included before beginning use. If any of the contents are incorrect, missing, or appear to be abnormal, please contact your Yokogawa dealer or representative. Name Q’ty Arm Base Probe holder User’ s Manual 1 1 1 1 Note Notes CAUTION The arm joint bends in the direction of the U-shaped notch. U-shaped notch This manual 3. Names of Parts Probe holder Probe positioning knob 7. Specification Arm Diameter of attachable probe: f8 to 13 mm Weight: Approximately 1.5kg External Dimensions Base Model label 109 65 20 Arm lock knob 109 46 Probe attachment knob 100 YOKOGAWA ELECTRIC CORPORATION, Communication & Measurement Business Headquarters Phone: (81)-422-52-6768, Fax: (81)-422-52-6624, E-mail: [email protected] YOKOGAWA EUROPE B.V. YOKOGAWA CORPORATION OF AMERICA Phone: (31)-33-4641858, Fax: (31)-33-4641859 Phone: (1)-301-916-0409, Fax: (1)-301-916-1498 YOKOGAWA ENGINEERING ASIA PTE. LTD. Phone: (65)-62419933, Fax: (65)-62412606 IM 7019�������������������� 19������������������ -01E 1st Edition