Download Synchronized Axes Control Module User Manual
Transcript
toc–ii Adjusting Command-word Speed and Acceleration Values . . . . . Adjusting Feedforward Parameters . . . . . . . . . . . . . . . . . . . . . . Using Acceleration Feedforwards . . . . . . . . . . . . . . . . . . . . . . . Adjusting P-I-D Gains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Finding the Value of the Dead Band Eliminator . . . . . . . . . . . . . . . . Saving Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using Ladder Logic Chapter 5 Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Obtaining Sample Ladder Program from the Internet . . . . . . . . . . . . To Access the Internet: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring Your SLC Processor, Off-line . . . . . . . . . . . . . . . . . . . . Using the Sample Ladder Program . . . . . . . . . . . . . . . . . . . . . . . . Copy Configuration Parameters to the SLC Processor . . . . . . . . Copy Configuration Parameters to the Module . . . . . . . . . . . . . . Back and Forth Motion with State-machine Logic . . . . . . . . . . . . Jogging the Axes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Responds to Hydraulics On/Off . . . . . . . . . . . . . . . . . . . . . . . . . Running Synchronized Axes . . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting B–1 B–2 B–2 Appendix C Transferring Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transferring Motion Commands and Axis Status . . . . . . . . . . . . Transferring Configuration Parameters . . . . . . . . . . . . . . . . . . . Using Floating-point for Values Above 32,767 . . . . . . . . . . . . . . . Using M0 and M1 Files for Initial Configuration . . . . . . . . . . . . . . . . M0 and M1 Memory Map for Ladder Logic . . . . . . . . . . . . . . . . . Bit Map of Configuration Word (e:0, e:16, e:32. e:48) . . . . . . . . . Using I/O Image Tables for Commands and Status . . . . . . . . . . . . . Bit Map of Command Mode Word . . . . . . . . . . . . . . . . . . . . . . . Bit Map of Axis Status Word . . . . . . . . . . . . . . . . . . . . . . . . . . . Publication 1746-6.19 – March 1998 A–2 A–2 A–2 A–2 Appendix B Wiring Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Minimizing Interference from Radiated Electrical Noise . . . . . . . . . . Checking Out the Wiring and Grounding . . . . . . . . . . . . . . . . . . . . Using Processor Files 6–1 6–1 Appendix A Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wiring Without the Interface Module 5–1 5–1 5–1 5–1 5–2 5–3 5–3 5–4 5–7 5–8 5–9 Chapter 6 Using LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Correcting Typical Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Module Specifications 4–7 4–7 4–8 4–8 4–9 4–10 C–1 C–2 C–2 C–3 C–4 C–4 C–5 C–5 C–6 C–6