Download HQ Pro-Stitcher for Infinity User Manual

HANDI QUILTER DIGITAL QUILTING SYSTEM
Designed by a Quilter, for Quilters.®
FOR
USER MANUAL
QM33002 • MAY 2015
How to use this manual
Notes, important notes, and cautions
NOTE: A NOTE indicates important information that helps you make better use of your
Handi Quilter product.
ÂÂ IMPORTANT: An IMPORTANT note provides information that is essential to properly using your
Handi Quilter product.
UU CAUTION: A CAUTION indicates a potential for causing harm to your quilting machine, the quilt, or
to yourself.
Online resources
Download a full-color version of this manual at: http://www.handiquilter.com/manuals/
Check for software updates to HQ Pro-Stitcher at: http://www.handiquilter.com/prostitcher-download/
Access videos about your Handi Quilter products: http://www.handiquilter.com/videocatalog/
Download tutorials for HQ Pro-Stitcher: http://www.handiquilter.com/education/pro-stitcher/
Participate in online forums with other Handi Quilter owners: http://www.handiquilter.com/forum/
Follow Handi Quilter on Facebook: https://www.facebook.com/HandiQuilter
© 2015 Handi Quilter, Inc. All rights reserved.
The information contained in this document is subject to change without notice. If you find any problems
in the manual, please report them to us in writing. This document is not warranted to be error-free.
Handi Quilter, Inc. assumes no responsibility or liability for any errors or inaccuracies that may appear in
the informational content contained in this manual.
Handi Quilter, HQ Infinity, HQ Avanté, HQ Fusion, HQ Sixteen, and HQ Pro-Stitcher are either trademarks or
registered trademarks of Handi Quilter, Inc.
Printed in the United States of America.
www.HandiQuilter.com
Table of Contents | 1.1
Table of Contents
1. Table of Conents...................................................................................1.2
2. Important Safety Instructions ..............................................................2.1
3. Installation Instructions .......................................................................3.1
Congratulations on your HQ Pro-Stitcher® purchase................................................................... 3.1
Grounding................................................................................................................................ 3.2
Parts List................................................................................................................................... 3.2
Installation.................................................................................................................................... 3.4
Installation of the X-Rack and Y-Rack........................................................................................... 3.5
To install the X-Rack............................................................................................................. 3.5
To install the Y-Rack............................................................................................................. 3.7
To attach the tablet computer.................................................................................................... 3.10
To turn on and shut down HQ Pro-Stitcher................................................................................ 3.11
To turn on HQ Pro-Stitcher................................................................................................ 3.11
To switch between HQ Pro-Stitcher and Infinity................................................................ 3.12
To shut down HQ Pro-Stitcher........................................................................................... 3.12
Getting started with HQ Pro-Stitcher......................................................................................... 3.13
To move the quilting machine after the software has been loaded.................................. 3.13
To use the USB flash drive................................................................................................. 3.13
To use an external keyboard ............................................................................................. 3.13
4. HQ Pro-Stitcher® Overview...................................................................4.1
Handlebar control ........................................................................................................................ 4.1
Enable or disable the carriage motors..................................................................................... 4.2
Overview of the HQ Pro-Stitcher screen...................................................................................... 4.2
Menu options........................................................................................................................... 4.2
Panel buttons........................................................................................................................... 4.3
Work Area.................................................................................................................................... 4.3
Selected vs. non-selected buttons........................................................................................... 4.4
Gray buttons............................................................................................................................ 4.4
Top toolbar buttons...................................................................................................................... 4.4
To get on-screen help.......................................................................................................... 4.5
To cycle the needle up or down to form a half stitch.......................................................... 4.5
To cycle the needle to the up position................................................................................ 4.5
To display the on-screen grid............................................................................................... 4.5
To quickly position the design and crosshairs on the screen............................................... 4.6
To move the on-screen view................................................................................................ 4.6
To view the design larger or smaller.................................................................................... 4.6
To move the design on the screen....................................................................................... 4.6
To select one or more designs............................................................................................. 4.7
To select a single design...................................................................................................... 4.7
To choose and group multiple designs................................................................................ 4.7
To name a group.................................................................................................................. 4.8
To change the stitch order of multiple designs.................................................................... 4.8
1.2 | Table of Contents
www.HandiQuilter.com
To measure distances in a design or on the quilt................................................................ 4.8
Crosshairs................................................................................................................................. 4.9
5. Design Menu........................................................................................5.1
Design history............................................................................................................................... 5.1
Baseline........................................................................................................................................ 5.2
To baseline a design............................................................................................................. 5.2
To work with design files.............................................................................................................. 5.4
To find the key code for encrypted files.............................................................................. 5.4
Open, close, save, and duplicate design files............................................................................... 5.4
To access recently used designs.......................................................................................... 5.4
To load a design from the design library............................................................................. 5.4
To save a design................................................................................................................... 5.5
To save a group as a design or a project.............................................................................. 5.5
To save designs or projects to a new folder......................................................................... 5.6
To duplicate a design........................................................................................................... 5.6
To view design information................................................................................................. 5.6
To load a Pro-Stitcher software update............................................................................... 5.7
To return a design to its original settings............................................................................. 5.7
Create and use areas.................................................................................................................... 5.8
To clear an area................................................................................................................... 5.8
To create a rectangular area using 2 Corner........................................................................ 5.8
To override the width or height of an area.......................................................................... 5.9
Multi-Point............................................................................................................................. 5.10
To create an area with multiple points.............................................................................. 5.10
To keep track of how many points you have marked........................................................ 5.10
Rotate designs............................................................................................................................ 5.11
2-Point Rotation..................................................................................................................... 5.12
To rotate a design according to an angle on the quilt....................................................... 5.12
To fine tune the angle of rotation...................................................................................... 5.13
Rotation of repeated designs................................................................................................. 5.14
To rotate repeated designs individually............................................................................. 5.14
To rotate repeated designs as a group.............................................................................. 5.14
Crop Menu................................................................................................................................. 5.15
Treatment of loose ends........................................................................................................ 5.15
To perform a tieoff at jump points.................................................................................... 5.15
To stitch between jump points.......................................................................................... 5.15
Crop designs based on areas or start and end points............................................................ 5.16
To crop everything outside the defined area..................................................................... 5.16
To crop everything inside the defined area....................................................................... 5.16
To isolate and crop a portion of a design.......................................................................... 5.16
Repeat Menu.............................................................................................................................. 5.18
Repeat Main........................................................................................................................... 5.18
To repeat a design............................................................................................................. 5.18
To change the size of the gap between repeated designs................................................. 5.18
To stretch a design to fill an area....................................................................................... 5.19
To calculate the optimal number of repeats for an area................................................... 5.19
Point 2 Point .......................................................................................................................... 5.19
To join horizontally repeated designs................................................................................ 5.19
www.HandiQuilter.com
Table of Contents | 1.3
To join vertically repeated designs.................................................................................... 5.20
Repeat Wrapping................................................................................................................... 5.20
To wrap rows..................................................................................................................... 5.21
To wrap columns................................................................................................................ 5.21
To horizontally wrap the design window........................................................................... 5.22
To vertically wrap the design window............................................................................... 5.22
To manually wrap the design window............................................................................... 5.23
Treatment of jump points...................................................................................................... 5.23
Resize Menu............................................................................................................................... 5.24
To resize a design............................................................................................................... 5.24
Skew / Align Menu..................................................................................................................... 5.26
To horizontally align blocks within an area....................................................................... 5.26
To align a triangle design................................................................................................... 5.27
To skew a design to fit an area.......................................................................................... 5.28
Freehand Menu.......................................................................................................................... 5.29
To switch to free-motion quilting...................................................................................... 5.29
Record the movements of your freehand quilting................................................................. 5.29
To record freehand motion................................................................................................ 5.29
To mark and record straight lines...................................................................................... 5.30
To add jumps to your recorded design.............................................................................. 5.30
Reposition Menu........................................................................................................................ 5.31
To position a design to the intersection of the crosshairs................................................. 5.31
To reposition a design based on the Home location......................................................... 5.33
To position a design based on the center point................................................................ 5.33
To position a design’s start point on the quilt................................................................... 5.33
To position a design’s end point on the quilt..................................................................... 5.33
To reposition a design up, down, left, or right................................................................... 5.34
6. Art & Stitch...........................................................................................6.1
To pass a design to Art & Stitch........................................................................................... 6.1
Licensing....................................................................................................................................... 6.2
Using a mouse or keyboard ........................................................................................................ 6.2
Updating Art & Stitch................................................................................................................... 6.2
7. Quilt Menu...........................................................................................7.1
To choose between stitching or tracing the design, bounding box, or area perimeter....... 7.1
To immediately stop the machine from quilting................................................................. 7.1
Before you stitch the design on the quilt..................................................................................... 7.2
To verify the position of the design’s bounding box on the quilt........................................ 7.2
To verify the position of the defined area on the quilt........................................................ 7.2
Move the quilting machine with Pro-Stitcher.............................................................................. 7.3
To change the speed at which the machine moves............................................................. 7.3
To move the quilting machine from within Pro-Stitcher..................................................... 7.3
To stitch a straight line using the Move buttons.................................................................. 7.3
Pro-Stitcher as a horizontal or vertical channel lock.................................................................... 7.4
To stitch a horizontal or vertical line with the channel lock................................................ 7.4
Adjust settings while quilting....................................................................................................... 7.4
To adjust commonly used stitch settings............................................................................. 7.5
To adjust the quilting speed while quilting.......................................................................... 7.5
1.4 | Table of Contents
www.HandiQuilter.com
To adjust the auto jump threshold while quilting................................................................ 7.5
To adjust stitches per inch while quilting............................................................................ 7.6
To manage the tieoff settings while quilting........................................................................ 7.6
To change the thread pullup settings while quilting............................................................ 7.7
To change the pause delay settings while quilting.............................................................. 7.7
Adjust settings while quilting is paused....................................................................................... 7.8
To pause quilting ................................................................................................................. 7.8
To see how far into a design the machine has stitched....................................................... 7.9
Change the start or end point of a design.................................................................................... 7.9
To begin quilting from a point other than the design’s start point.................................... 7.10
To end quilting at a point other than the design’s end point............................................ 7.10
To adjust start and end points with the scroll bars............................................................ 7.10
To set a start or end point to a jump point in the design.................................................. 7.10
8. Settings Menu......................................................................................8.1
Control how fast Pro-Stitcher operates........................................................................................ 8.1
To set the default speed...................................................................................................... 8.1
Control how Pro-Stitcher handles jumps...................................................................................... 8.1
To set the Auto Jump threshold.......................................................................................... 8.2
Control the number of stitches per inch...................................................................................... 8.2
To set the stitches per inch.................................................................................................. 8.2
Control how Pro-Stitcher performs tie-offs.................................................................................. 8.3
To have Pro-Stitcher perform a tie-off at the beginning of stitching................................... 8.3
To have Pro-Stitcher perform a tie-off at the end of stitching............................................. 8.3
To indicate how many tie-off stitches Pro-Stitcher will perform......................................... 8.3
To set the length of each tie-off stitch................................................................................. 8.3
To select the method of tie-off stitch: Micro or Tack........................................................... 8.4
Control how Pro-Stitcher handles bobbin-thread pullups............................................................ 8.4
To turn on bobbin-thread pullups....................................................................................... 8.4
To turn on automatic bobbin-thread pullups...................................................................... 8.5
Control the delay following a bobbin-thread pullup.................................................................... 8.5
To set the Pause Delay......................................................................................................... 8.5
To set Pause Delay in seconds............................................................................................. 8.5
To set Pause Delay in inches................................................................................................ 8.5
Advanced Menu........................................................................................................................... 8.6
General options....................................................................................................................... 8.6
To create a simulation license............................................................................................. 8.6
To use the Pro-Stitcher simulation license.......................................................................... 8.8
To turn on or off the Thread Break Sensor.......................................................................... 8.8
To verify settings before quilting ........................................................................................ 8.8
Communications options......................................................................................................... 8.8
To stop communications between Pro-Stitcher and the quilting machine ......................... 8.9
To reconnect motors........................................................................................................... 8.9
To reconnect the machine................................................................................................... 8.9
Speed profile.............................................................................................................................. 8.10
To set your speed profile................................................................................................... 8.10
Motor Option............................................................................................................................. 8.10
When to adjust the motor torque limit................................................................................. 8.10
To adjust the motor torque limit....................................................................................... 8.11
www.HandiQuilter.com
Table of Contents | 1.5
Logging options.......................................................................................................................... 8.11
About.......................................................................................................................................... 8.11
Shut Down ................................................................................................................................. 8.11
To shutdown all software and power down the computer............................................... 8.11
To shutdown the software and computer, and then start up again.................................. 8.11
To exit Pro-Stitcher but keep the computer running......................................................... 8.12
To restart the Pro-Stitcher software from Windows.......................................................... 8.12
9. Troubleshooting ...................................................................................9.1
10. Warranty .........................................................................................10.1
Warranty Registration Card ...................................................................................................... 10.4
Training Checklist ...................................................................................................................... 10.5
11. Handi Quilter Printouts ...................................................................11.1
12. Tutorials ...........................................................................................12.1
13. Designs ............................................................................................13.1
14. My Ideas ..........................................................................................14.1
1.6 | Table of Contents
www.HandiQuilter.com
2. Important Safety Instructions
Save these instructions
This machine is intended for household use.
Disclaimer
Handi Quilter and its Representatives are in no way legally responsible or liable for damage to the
HQ Pro-Stitcher when used improperly or not in accordance with the guidelines stated in this manual or
when used on machine quilting frames not recommended by Handi Quilter.
Read all instructions before using
When using any machine, basic safety precautions should always be taken, including the following: Read all
instructions before using.
WARNING - To reduce the risk of burns, fire, electric shock, or
injury to persons:
The HQ Pro-Stitcher quilting machine should never be left unattended when plugged in.
Always unplug the machine from the electric outlet immediately after using and before cleaning.
•
•
•
•
•
•
•
•
•
•
•
•
•
Do not allow to be used as a toy. Close attention is necessary when this quilting machine is used by
or near children.
Use this quilting machine only for its intended use as described in this manual. Use only
attachments recommended by the manufacturer as contained in this manual.
Never operate this quilting machine if it has a damaged cord or plug, if it is not working properly, if
it has been dropped or damaged, or dropped into water. Return the quilting machine to the nearest
authorized dealer or service center for examination, repair, electrical or mechanical adjustment.
Never operate the machine with any air openings blocked. Keep ventilation openings of the
machine free from the accumulation of lint, dust, and loose cloth.
Never drop or insert any object into any opening.
Do not use outdoors.
Do not operate where aerosol (spray) products are being used or where oxygen is being
administered.
To disconnect, shut down the computer, then disconnect all cables.
Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
Keep fingers away from all moving parts.
Always unplug the machine from the electrical outlet when removing covers, lubricating, or when
making any other user servicing adjustments mentioned in the instruction manual.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory, or mental capabilities, or lack of experience or knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
Use only the power cord set provided by the manufacturer or a certified replacement set from
the manufacturer.
www.HandiQuilter.com
Safety | 2.1
Read these instructions before using the machine.
To use the machine safely
1. Keep hands and loose clothing away from wheels, gears or other moving parts.
2. Turn the machine off and unplug the cord in the following cases:
• when you have stopped using the machine
• when you replace or remove the quilting machine needle or any other part
• in case of failure when you use the machine
• when you check or clean the machine
• when you leave the machine unattended
3. Connect the machine directly to the wall outlet. Do not use extension cords.
To increase the life of your machine
1. Do not store this machine in areas exposed to direct sunlight or high humidity. Never use or store the
machine near a heater, an iron, a halogen lamp or other hot things.
2. Clean the computer monitor with a soft, lint-free rag. If necessary, dampen the rag with a small amount
of isopropyl alcohol. Do not use any other cleaners on the computer monitor.
3. Use only neutral soaps or detergents to clean the carriage. Benzene, solvents and scouring powders can
damage the machine and therefore should never be used.
4. Do not drop or bump the machine.
5. Always consult the manual to replace or fix any other part of the machine.
To repair or adjust the machine
•
If the machine breaks down or needs adjustment, first check the troubleshooting chart in the
appendix to inspect and adjust the machine yourself.
How to use this manual
Notes, important notes, and cautions
NOTE: A NOTE indicates important information that helps you make better use of Pro-Stitcher.
ÂÂ IMPORTANT: An IMPORTANT note provides information that is essential to properly using your
Pro-Stitcher.
UU CAUTION: A CAUTION indicates a potential for causing harm to your quilting machine, the quilt,
or to yourself.
2.2 | Safety
www.HandiQuilter.com
Consignes de sécurité importantes
Conservez ces consignes
Cette machine est destinée à un usage domestique.
Avertissement
Handi Quilter et ses représentants ne sont en aucun cas juridiquement responsables des dommages causés
à HQ Pro-Stitcher lorsque cellle-ci est utilisée de manière inadéquate ou non conforme aux consignes
énoncées dans ce manuel ou lorsqu’elle est utilisée sur des cadres de machine à quilter non recommandés
par Handi Quilter.
Lisez toutes les consignes avant d’utiliser le produit
Lorsque vous utilisez une machine, vous devez toujours prendre des précautions de sécurité de base,
notamment ce qui suit : lisez toutes les consignes avant d’utiliser le produit.
AVERTISSEMENT : pour réduire le risque de brûlures, d’incendie, de
choc électrique ou de blessures :
Ne jamais laisser la machine à quilter HQ Pro-Stitcher sans surveillance lorsqu’elle est branchée.
Débranchez toujours la machine de la prise électrique immédiatement après usage et avant de la nettoyer.
•
•
•
•
•
•
•
•
•
•
•
•
•
Ne pas l’utiliser comme un jouet. Il est nécessaire de faire preuve de vigilance lorsque cette
machine à quilter est utilisée à côté ou à proximité d’enfants.
Utilisez cette machine à quilter uniquement pour l’usage prévu décrit dans ce manuel. Utilisez
uniquement les accessoires recommandés par le fabricant décrits dans ce manuel.
Ne jamais utiliser cette machine à quilter si le cordon ou la fiche est endommagé, si elle ne
fonctionne pas correctement, si on l’a fait tomber ou endommagé, ou si elle est tombée dans l’eau.
Renvoyez la machine à quilter au revendeur ou centre de service après-vente agréé le plus proche
pour examen, réparation, ou réglage électrique ou mécanique.
Ne jamais utiliser la machine si des ouvertures d’air sont bloquées. Gardez les ouvertures de
ventilation de la machine libérées d’accumulation de peluches, poussières et morceaux de tissu.
Ne jamais faire tomber ou insérer un objet dans une ouverture.
Ne pas utiliser à l’extérieur.
Ne pas utiliser là où des aérosols (vaporisateurs) sont utilisés ou de l’oxygène est administré.
Pour déconnecter, arrêtez l’ordinateur, puis débranchez tous les câbles.
Ne pas débrancher en tirant sur le cordon. Pour débrancher, saisir la fiche, non le cordon.
N’approchez pas les doigts des parties mobiles.
Débranchez toujours la machine de la prise électrique pour retirer des couvercles, lubrifier, ou pour
tout autre réglage d’entretien de l’utilisateur mentionné dans le manuel d’instruction.
Cet appareil n’est pas destiné intended à être utilisé par des personnes (y compris les enfants)
dotées de facultés physiques, sensorielles, ou mentales réduites, ou manquant d’expérience ou de
connaissances, sauf si elles ont été formées et encadrées sur l’utilisation de cet appareil par une
personne responsable de leur sécurité.
Utilisez uniquement le cordon d’alimentation fourni par le fabricant ou une pièce de rechange
certifiée par le fabricant.
www.HandiQuilter.com
Safety | 2.3
Lisez ces consignes avant d’utiliser la machine.
Pour utiliser la machine en toute sécurité
1. N’approchez pas les mains et les vêtements amples des roues, des engrenages ou des autres
pièces mobiles.
2. Mettez la machine hors tension et débranchez le cordon dans les cas suivants :
• lorsque vous avez fini d’utiliser la machine
• lorsque vous remplacez ou retirez l’aiguille ou une autre pièce de la machine à quilter
• en cas de défaillance lorsque vous utilisez la machine
• lorsque vous inspectez ou nettoyez la machine
• lorsque vous laissez la machine sans surveillance
3. Connectez la machine directement à la prise murale. Ne pas utiliser de rallonges.
Pour augmenter la durée de vie de votre machine
1. Ne pas ranger cette machine dans des endroits exposés à la lumière directe du soleil ou à une forte
humidité. Ne jamais utiliser ni ranger la machine à proximité d’un radiateur, d’un fer à repasser, d’une
lampe halogène ou d’autres objets brûlants.
2. Nettoyez l’écran d’ordinateur avec un chiffon doux non pelucheux. Au besoin, humidifiez le chiffon avec
une petite quantité d’alcool isopropylique. Ne pas utiliser d’autres produits de nettoyage sur l’écran
d’ordinateur.
3. Utilisez uniquement des savons ou détergents neutres pour nettoyer le chariot. Le benzène, les solvants
et les poudres à récurer peuvent endommager la machine et ne doivent donc jamais être utilisés.
4. Ne pas faire tomber ou cogner la machine.
5. Consultez toujours le manuel pour remplacer ou réparer toute autre pièce de la machine.
Pour réparer ou régler la machine
•
Si la machine tombe en panne ou doit être réglée, consultez d’abord les consignes de dépannage
figurant en annexe pour inspecter et régler vous-même la machine.
2.4 | Safety
www.HandiQuilter.com
3. Installation
Congratulations on your HQ Pro-Stitcher® purchase
Handi Quilter is proud to offer you easy-to-use quilting machines and computer-guided quilting using the
latest technology with the best value for your money. We provide inspiration and education to enhance
your transition into computer-guided machine quilting.
Because the world of computer-guided quilting is constantly changing, we invite you to keep up with us by
checking our website frequently for news, software updates, tutorials, and more.
Go to www.HandiQuilter.com for:
•
•
•
•
•
•
•
Updates to the HQ Pro-Stitcher software (provided free as long as you own your machine)
A full-color version of this manual that can be downloaded and printed
Updates to this manual
Step-by-step tutorials to help you learn how to use HQ Pro-Stitcher
Free design downloads
News about hardware upgrades or new machines
Links to educational information: webinars, retreats, and more
Want to be in the know?
Sign up to join the Handi Quilter e-mail Newsletter list to receive notice of updates, upgrades, special
offers, contests, new products and free stuff at: www.HandiQuilter.com/newsletter/subscribe/.
Machine packaging information
Keep the carton and packing materials. You will need them in the event that you need to return the
machine to the dealer or send it for repair. If you do not pack the machine properly or if you do not use the
correct packaging materials, the machine could be damaged. Handi Quilter is not liable for damage that
occurs during return shipping.
Handi Quilter contact information
Handi Quilter, Inc.
501 N 400 W
North Salt Lake, Utah 84054
Toll-free phone: (877) 697-8458
Local phone: (801) 292-7988
Email Address: [email protected]
Website: www.HandiQuilter.com
www.HandiQuilter.com
Installation | 3.1
Optional U.S. Grounding
GROUNDED OUTLET BOXES
TAB FOR
GROUNDING
SCREW
METAL
SCREW
GROUNDING PIN
ADAPTER
(A)
(B)
(C)
This product is for use on a nominal 120 V or nominal 220 V circuit, and has a grounding plug that looks
like the plug illustrated in sketch A above. A temporary adapter, which looks like the adapter illustrated in
sketches B and C, may be used to connect this plug to a 2-pole receptacle as shown in sketch B if a properly
grounded outlet is not available. The temporary adapter should be used only until a properly grounded
outlet can be installed by a qualified electrician. The green colored rigid ear, lug, and the like, extending
from the adapter, must be connected to a permanent ground such as a properly grounded outlet box cover.
Whenever the adapter is used, it must be held in place by the metal screw.
ÂÂ IMPORTANT: In Canada, the use of a temporary adapter is not permitted by the Canadian Electric
Code.
Parts List
This list shows the parts that come with the HQ Pro-Stitcher.
NOTE: The parts photographed in this manual may look different from the ones you received.
Item
A. Blue X-rack (12-foot Flexirack)
B. Flexirack clamps and screws
3.2 | Installation
Quantity
1
Photo
4
www.HandiQuilter.com
C. 3/32-inch drill bit
1
D. EZ Carriage
1
E. Computer bracket
1
F. Y-rack
F-1. Y-rack end cap
1
F-2. Y-rack
G. Power cord assembly
G-1. 10-foot power cord
1
G-2. 2-foot power cord (quilting machine to
carriage)
1
G-3. 2-foot power cord (wall to filter box)
1
G-4. Power filter box
1
H. USB flash drive
1
I. Art & Stitch software
1
www.HandiQuilter.com
Installation | 3.3
J. USB cable
1
K. Computer power cord
1
L. Manual engagement/disengagement tool
1
M. Data cable
1
N. HQ Pro-Stitcher tablet computer
NOTE: The model of the HQ Pro-Stitcher
computer may be different from the one
pictured.
1
Installation
These instructions are for installing HQ Pro-Stitcher on the HQ Infinity . Handi Quilter recommends
installation by an authorized HQ Pro-Stitcher Representative if available.
Tools required
•
•
•
•
•
•
•
Power drill
3mm Allen wrench
4mm Allen wrench
5mm Allen wrench
Slotted screwdriver (one large and one small)
Phillips screwdriver (one large and one small)
Manual engagement/disengagement tool (see Parts List, item O)
3.4 | Installation
www.HandiQuilter.com
Installation of the X-Rack and Y-Rack
To install the X-Rack
1. Remove the blue 12-foot Flexirack (see Parts List, item
A) and the Pro-Stitcher carriage (see Parts List, item
D) from the box.
2. Place the Pro-Stitcher carriage on the frame. Starting
at one end of the table, begin mounting the blue
Flexirack to the front of the table while aligning it to
the front white gear on the carriage.
Peel back a few inches of the pink protective layer of
the tape. Position the blue Flexirack by aligning
it to the white gear as you move down the table.
Press down on the blue Flexirack to stick it firmly to
the table.
3. Use the carriage as a guide and align the blue
Flexirack with the white gear along the length of
the table (see arrow at right), removing the pink
protective layer and pressing downward on the
blue Flexirack while moving down the entire length
of the table.
4. Double check the alignment of the carriage white gear with the blue Flexirack by rolling the carriage
along the entire length of the table.
www.HandiQuilter.com
Installation | 3.5
5. Trim the Flexirack to length using a knife or wire
cutters. The blue Flexirack does not need to extend
the full width of the table and can be a couple of
inches shorter on either end.
6. At both ends of the blue Flexirack, use two of the
small metal clamps (see Parts List, item B) to hold the
ends firmly in place. The clamps have a hole through
the center and a lip on one end. The lip should be on
the side opposite the blue Flexirack. Place the clamps
where they will be attached and drill pilot holes
using the 3/32-inch drill bit and then use a Phillips
screwdriver to fasten the clamps on both sides of the
Flexirack to the table.
UU CAUTION: Do not use the larger drill bit included in the emergency repair kit, as this is the wrong
size for the Flexirack clamps.
NOTE: As an alternative, use one clamp at each end. Slide the lip of the clamp over the last gear
of the blue Flexirack, drill a pilot hole, and screw in place.
3.6 | Installation
www.HandiQuilter.com
To install the Y-Rack and carriage
1. Carefully lay the quilting machine on its left side
(looking from the front).
Remove the end cap from the front-right side of the
Infinity. Use a 5mm Allen wrench to loosen (but not
fully remove) the screw in the track as shown. Then
slide off the end cap.
2. Insert the T-nut and washer into the HQ Pro-Stitcher
Y-rack end cap (see Parts List, item F-1).
3. Attach the Y-rack end cap to the Infinity. Note that the
T-nut goes into the track and the head of the screw
goes above the metal with the plastic between the
lower-side leg and the lower-center arm extrusion.
www.HandiQuilter.com
Installation | 3.7
4. Use the M6x16 screw provided and tighten the
front screw of the Y-rack end cap with the 5mm
Allen wrench.
5. Then fully tighten the top rack screw.
6. Attach the Y-rack white track (see Parts List, item
F-2). Remove the plastic backing from the white
Y-rack. While holding the Y-rack at an angle, slide the
notched end into the Y-rack end cap.
7. Carefully align the Y-rack along the lip of the Infinity
base as shown. Press it into place.
3.8 | Installation
www.HandiQuilter.com
8. Locate the M4x12 screw and screw into the machine
base.
A
9. Place the Infinity on the HQ Pro-Stitcher EZ Carriage.
ensure that the Y-rack gear engages with the Y-rack.
You may need to manually engage the EZ carriage
using the manual engagement tool provided.
B
C
D
10. Connect all of the cables at the back of the machine.
Connect the HQ Pro-Stitcher cable (A).
11. Connect the stitch regulator cable (B).
12. Connect the HQ Pro-Stitcher power cable (C).
13. Connect the Infinity power cable (D).
www.HandiQuilter.com
Installation | 3.9
To attach the tablet computer
1. If necessary, remove the front display by unscrewing
the 2.5mm hex screws that attach the dislay to the
front bracket.
2. Attach the HQ Pro-Stitcher computer bracket (see
Parts List, item E) by aligning the four holes in the
bracket with the four holes along the top of the
display bracket.
3. Use the four M4x7mm hex screws (provided). Insert
them into the Pro-Stitcher bracket and the Infinity
front display bracket. Loosely tighten all four screws
with a 3mm Allen wrench and then fully tighten
them.
4. Place the tablet computer into the HQ Pro-Stitcher
computer bracket. The top part of the bracket is
spring-loaded so you can widen the opening enough
to get the tablet computer in place.
3.10 | Installation
www.HandiQuilter.com
5. Locate the USB cable provided with HQ Pro-Stitcher
(see Parts List, item J). Connect one end to the USB
port on the tablet computer and the other end to the
USB port on the side of the Infinity.
Locate the power cord (see Parts List, item K) and
connect one end to the side of the tablet computer
and the other end to the power connector on the side
of the Infinity.
ÂÂ IMPORTANT: Your tablet may be a different make or model than the one shown. Connect the USB
and power cables in their proper location based upon your make and model of tablet.
To turn on and shut down HQ Pro-Stitcher
Check that the power cord is plugged into the power supply located at the back of the carriage. Then plug
in the barrel-shaped power connector to the bottom of the black box behind the computer and the short
power cord from the black box to the computer. If the cable is unplugged, the computer will continue to
run on battery power until the charge has been used up.
To turn on HQ Pro-Stitcher
•
Press the power switch, usually located at the top-right side of the tablet computer.
When you start the Pro-Stitcher computer, both the Pro-Stitcher software and the Infinity software console
start up.
www.HandiQuilter.com
Installation | 3.11
To switch between Pro-Stitcher and Infinity
Use the menu bar in the top left corner of the screen to switch between using the Pro-Stitcher software
and the Infinity software console.
Open this menu.
Open the
onscreen
keyboard.
Switch to ProStitcher
See what the
video camera is
displaying
Close this menu.
Switch to Infinity
console
Start Art &
Stitch
To shut down HQ Pro-Stitcher
•
Choose Shut Down from the Pro-Stitcher menu. Then choose the Shutdown button at the bottom
of the screen. This shuts down both the Pro-Stitcher software and the tablet computer.
ÂÂ IMPORTANT: If you don’t see the Shutdown button, press the power switch on the tablet computer
to continue shutting down the Pro-Stitcher computer.
ÂÂ IMPORTANT: If you leave the Pro-Stitcher computer powered on with the power cord unplugged,
the computer will begin running off battery power. The computer will shut down when no battery
power remains.
ÂÂ IMPORTANT: If the Pro-Stitcher computer is left on for a long period of time, the screen may turn
black and enter a sleep mode. Tap the screen or press the Windows button below the screen to
turn on the screen again. It may be necessary to drag a finger upward on the start-up screen to
access Pro-Stitcher.
ÂÂ IMPORTANT: Disable the auto-rotate feature for your tablet computer so that it only works in
landscape, or horizontal, mode. Depending on your computer, you will do this by pressing a button
on the top or side of the tablet computer or by using the Microsoft Windows Control Panel Display
options. Refer to the owner’s manual that came with your tablet computer for more information.
3.12 | Installation
www.HandiQuilter.com
Getting started with HQ Pro-Stitcher
To move the quilting machine after the software has been loaded
•
To move the quilting machine after the software has loaded, the motors should be disengaged.
Press the Disable Motors button in the upper-right corner of the screen to disengage the motors.
Note that the button changes to say Enable Motors.
Use the options on the Freehand screen to alternate between computerized quilting and free-motion
quilting.
•
Choose Design, then Freehand. Select the Free Motion button. Pro-Stitcher automatically raises the
quick-release levers to disengage the carriage gears from the Flexirack. Select the Engaged
button to once again use Pro-Stitcher for computerized quilting.
To use the USB flash drive
A USB flash drive is included with the Pro-Stitcher and is pre-loaded with more than 180 designs. These
designs have also been loaded to the drive on the tablet computer, so the USB flash drive is the backup
copy of the designs. You can also copy downloaded digitial quilting motifs or update both the Pro-Stitcher
and Infinity console software from the USB drive.
•
Insert the USB drive in the USB port on the front-left side of the Infinity to access the USB drive
through Pro-Stitcher or the Infinity application console.
ÂÂ IMPORTANT: It is not necessary to power down Pro-Stitcher or the Infinity to install or remove the
USB flash drive, but take care not to remove the flash drive while the system is saving to or loading
from the drive.
To use an external keyboard
An external keyboard is helpful when using Art & Stitch on the Pro-Stitcher computer. Use a keyboard
and mouse (wired or wireless) by attaching them (or the wireless transmitter) to USB port on the tablet
computer or the Infinity.
www.HandiQuilter.com
Installation | 3.13
5. Design Menu
The Design menu functions open, modify, position, and save quilting designs. Much of what you will do
with Pro-Stitcher will be from this menu.
After you select Design, two clusters of buttons appear on the lower-left and lower-right corners of
the screen.
Red dots mark the start
of a jump, the point
where Pro-Stitcher
stops stitching so you
can tie off the thread.
Start (red) and stop
(green) points
Bounding box
The purple dashed line
shows the jumps (not
stitched).
Design
Green dots mark the
end of the jump and the
beginning of the next
stitching segment.
Use these buttons to display
portions of the design.
Use these buttons
to keep track of
changes you make
to the design.
The four buttons in the lower-left corner of the Design screens turn on or off the display of a portion of the
design.
Select to show or
hide the design.
Select to show or
hide the jump points.
Select to show or hide
the blue bounding box
and the area box.
Select to show or hide
the start and stop
points.
The four buttons in the lower-right corner of the Design screen help to keep track of changes made to the
design.
Select to undo the
last function performed.
Select to redo the last
function that was undone.
Select to baseline a
design, or have the
software treat it as
a new design.
Select to see a list of the
functions that have been
performed since opening a
design.
Design history
•Press History to show a list of the functions that have been performed since opening a design.
www.HandiQuilter.com
Design Menu | 5.1
The item at the top of the list is
the first function performed and
the item at the bottom of the
list is the most recent function.
Use your finger to drag the list
up or down to reveal more of
the history.
Press any of the
history items to return the
design to the state it was
when that function was
performed.
To clear the history of recent functions
•To clear the history of recent actions, select Clear History.
After clearing the history, the history is gone and you will not be able to Undo or Redo previous actions. As
you perform new actions, they are added to the history and the Undo and Redo buttons will work on those
actions.
Baseline
Pro-Stitcher has very flexible design capabilities. Each function you choose is reprocessed and reapplied
when the next function is performed. For example, you can skew a design to fit an area and then rotate the
skewed design. The design continues to skew as it rotates to keep it within the area.
The baseline feature enables you to freeze the design at any point in the design process, essentially
freezing all of your design choices. The design isn’t saved to the computer, but the resize, rotation, and
crop settings are maintained until you change them.
To baseline a design
•
At any point in the design process, select Baseline.
After you baseline a design, you will not be able to use any of the design reset buttons to return the design
to its original settings. However, you will be able to use the Undo or Redo functions based on the design
history.
After you baseline a group, the designs are merged and the group is treated as a single design. You will not
be able to work with the designs individually.
5.2 | Design Menu
www.HandiQuilter.com
Machine Quilting Tip: Practical uses for Baseline
Use the Baseline function to stitch a quilt with multiple, identical blocks. Mark the area of
the first block, fit the design to the block using Skew or other functions to modify the design,
and then baseline the design. Quilt the block. Clear the Area. The design will maintain
its size and shape. Reposition the design to another block and quilt the design. Continue
quilting the baselined design on the blocks throughout the quilt.
Use Baseline when you want to crop multiple shapes from a design. Mark and crop the first
area, and then select Baseline. Clear the area and create a new area in another location for
cropping. Continue to mark and crop as desired, followed by selecting Baseline after each
crop to create multiple cropped regions in a design.
www.HandiQuilter.com
Design Menu | 5.3
To work with design files
Pro-Stitcher reads five file types: .hqf, .hqp, .qli, .txt, and .tap. Pro-Stitcher can also read .hqx encrypted
files, provided you use a key code that is unique to your HQ Pro-Stitcher computer. You will need this code
when you purchase the encrypted .hqx designs.
To find the key code for encrypted files
•
Select Settings, Advanced, About. A pop-up box with the key code then appears on the HQ ProStitcher screen.
Open, close, save, and duplicate design files
To access recently used designs
•Choose Recent to see a list of the most recent designs you have opened. Then select the design you
want to use.
This shortcut enables you to open recent designs without searching through the design library.
Press Open to see
the library of quilting
designs.
Press Recent to show the most
recent designs you’ve opened.
Press Close to close
the selected design.
To load a design from the design library
1.To load a design, select Design, File, and then select Open.
2.Browse to the design stored either on the C: drive or on a USB drive. The different design file types
have color-coded backgrounds as follows:
•
•
•
•
•
•
*.hqf: beige
*.hqv: green
*.hqp: purple
*.qli: light blue
*.txt: lavender
*.tap: pink
5.4 | Design Menu
www.HandiQuilter.com
Use these buttons to navigate among
folders on the current drive or to open
folders on a USB drive.
Select a design and
then choose Delete
File to remove it from
your computer.
Choose Refresh to
reload the thumbnails
in the selected folder.
Designs are organized into
four folders: block designs,
continuous line designs, corner
designs, and triangle designs.
Select a design and
press Open to load it
or press Cancel to exit.
Loading the thumbnails may take a few moments, depending on how many designs are stored in
the selected folder and how intricate those designs are. While the thumbnails load, a colored block
with the name of the file type will be visible in place of the actual design thumbnail.
3.Double-tap the name of the desired file or single tap and then press Open to load the design. A
prompt to Clear Area appears on-screen. Choose Yes to clear any area you have defined or No to
leave the area as designated.
Designers Showcase
Pro-Stitcher comes with a large library of quilting motifs from digital quilt motif designers.
Select Designers Showcase and then select the designer’s name to see the motifs. Then
choose the design you want to use and select Open. These designs are in a vector file
format, .hqv. If you save the design, either to a new name or overwrite the existing .hqv file,
Pro-Stitcher changes it to an .hqf file format.
To save a design
Pro-Stitcher prompts you to save your work when closing the software or closing a design. However, it is a
good idea to save your work regularly.
•Press Save to save the design in its current state. The design library appears with the name of the
current design loaded.
• To overwrite the existing design with that name, press Save.
• To save a copy of the design to a new name, enter a new name using the pop-up keyboard and
then press Save.
• To cancel without saving the design, press Cancel.
To save a group as a design or a project
You can save a group of designs as a design or as a project. If you save a group as a design, Pro-Stitcher
creates a single design. When you load it again in the future, you will not be able to work with the designs
independently.
www.HandiQuilter.com
Design Menu | 5.5
•To save a group as a design, select the group, select Save and then select Design before giving it a
filename and saving.
If you save a group of designs as a project, Pro-Stitcher saves each design independently so that when you
load the project again, you will be able to modify the designs individually.
•To save a group as a Project, select the group, select Save and then select Projects. Give the group a
file name and select Save on the Save Project screen.
To save designs or projects to a new folder
•To save the design or project to a new folder, browse to the desired folder using the folder tabs on
the left side of the design library. Alternatively, use the navigation buttons at the top of the screen
to move among folders and drives.
Copies and pastes
the selected design.
Displays information
about the selected design.
Resets the design
to its original
design settings.
Loads Pro-Stitcher software
updates you’ve downloaded to a
USB drive.
To duplicate a design
•Select the design or group you want to copy and choose Duplicate.
The duplicated design is placed at the current position of the crosshairs. If the crosshairs have not been
moved, the duplicate(s) will be in exactly the same place as the original. Choose Reposition or Drag to
move the duplicated design to a different location in the work area. Alternately, select the design or group
and drag it to a new position on the screen.
To view design information
Many designers include copyright information and instructions on how to use their designs within the
design file itself.
5.6 | Design Menu
www.HandiQuilter.com
•To view design information, load the design file and press Copyright. A pop-up window displays the
information contained within the design file related to copyrights and user instructions.
To load a Pro-Stitcher software update
As updates for the Pro-Stitcher software become available, download the updated file from the Handi
Quilter website, www.HandiQuilter.com.
•
Select the Downloads link at the top of the page. Then select Pro-Stitcher Software Update.
Follow the instructions for downloading the latest update, save the update file to a USB flash drive, and
plug the USB flash drive into a USB port on the Pro-Stitcher computer. Wait for approximately 10 seconds
while Pro-Stitcher accesses the USB flash drive. Follow the instructions included on the website for
installing the update.
To return a design to its original settings
Many settings in Pro-Stitcher remain set even after other operations are performed. For example, you
might rotate a design, repeat it multiple times, resize it, and more.
•To turn off design changes you’ve made since the last baseline, press Reset All.
If a new design is loaded or you baseline the design, Reset All is automatically performed.
www.HandiQuilter.com
Design Menu | 5.7
Create and use areas
A quilting area is a portion of the Pro-Stitcher screen that represents an area on the quilt. Within this area,
you can place designs, repeat them, stretch them, skew them, crop them, and so forth, knowing that
everything within the defined area on the screen will match up with the corresponding area on the quilt.
A purple line
shows the
defined area.
Shows how many
points you have
defined for the
area.
Select to clear
a defined area.
Use 2-Corner to easily
create rectangular areas.
Use Multi-Point to create areas with
three or more points, such as hexagons.
Create an area at any point during the design process. You can create only one area at a time.
To clear an area
•Select Area on the menu, then select Clear.
Areas can be a simple rectangle, created by identifying two opposing corners (2-corner areas), or they can
be more complex, unique shapes, created by plotting multiple points (multi-point areas). The area is fixed
in position once it is defined and cannot be moved.
To move or adjust an area, first clear the current area and then recreate it. To fit the area within the work
area of the screen, use Zoom.
To create a rectangular area using 2 Corner
1.Move the quilting machine so the needle lines up with
one corner of the desired area on the quilt. (It may be
necessary to press the Disable Motors button at the topright corner of the screen.) Then press 2-Corner or press
the star button the the Infinity handlebars.
5.8 | Design Menu
www.HandiQuilter.com
2.A purple dot displays on the screen to indicate the first
corner. Move the quilting machine so the needle lines up
with the opposite corner of the desired area on the quilt.
3.Select 2-Corner again or press the star button on the
Infinity handlebars. A purple rectangle indicates the
quilting area.
To override the width or height of an area
The width and height of the area appear in the number boxes on the screen. You can modify these values
to create an area beyond what the quilting machine can reach.
•Touch either the Area Width number box or the Area Height number box, enter a new value in
the number pad that appears, and then press Enter. After you enter a value in either box, the area
converts to a rectangle with the new dimension(s).
www.HandiQuilter.com
Design Menu | 5.9
Multi-Point
For more complex areas, use Multi-Point to mark multiple points to create triangles, hexagons, octagons,
or any shape with three or more points.
To create an area with multiple points
1. M
ove the quilting machine so the needle lines up with one corner of the desired area on the quilt.
It may be necessary to press the Disable Motors button at the top-right corner of the screen. Press
Multi-Point or press the diamond button the the Infinity handlebars.
2. Move the machine to a second point along the perimeter
of the quilting area and press Multi-Point or the diamond
button again. A purple line joins the two marked points.
3. M
ove the machine to a third point along the perimeter of
the quilting area and press Multi-Point or the diamond
button again. Pro-Stitcher automatically closes the shape
back to the first point when the third point is marked,
creating a purple triangle to indicate the multi-point area.
4. Mark other points as desired to create a detailed quilting
area.
To keep track of how many points you have marked
•
The Point Count box displays how many points you have marked. When you clear the area, the
point count goes back to zero.
5.10 | Design Menu
www.HandiQuilter.com
Rotate designs
•Select Design and then Rotate to see the options for rotating designs.
Number box
Flips the design
vertically.
Flips the design
horizontally.
Resets the rotation
back to zero.
Rotates the design
45° clockwise or
counterclockwise.
Rotates the design 1°
or 0.1° clockwise or
counterclockwise.
Original design
Design rotated 45° clockwise
Design rotated 45°
counterclockwise
www.HandiQuilter.com
Design Menu | 5.11
Design mirrored
Design flipped
In addition to using the rotation buttons, press the number box and enter a rotation value on the number
pad. Enter a positive number to rotate the design clockwise or a negative number to rate the design
counterclockwise.
2-Point Rotation
2-Point Rotation uses the quilting machine to identify a line that represents the rotation angle. You’ll set a
start point and an end point to create a line that represents the angle to which the design will align.
To rotate a design according to an angle on the quilt
1. Move the quilting machine to a point on the quilt left of the
line to follow and press 2 Point Start. Note the position of
the crosshairs in the image at the right.
2. Move the machine to a point further to the right along the
angled line. Note the position of the crosshairs in the image
at the right.
5.12 | Design Menu
www.HandiQuilter.com
3. Select 2 Point End. The design rotated to match the angle
created by the two points selected in steps 1 and 2
The rotation angle appears in the number box and the design rotates to match the angle, -49.10 degrees in
this example.
Machine Quilting Tip: Use 2-Point rotation to quilt sashing in an on-point quilt
Create an area that represents the sashing to be quilted. Load the design and make design
changes, such as resize and create repeats. The design will be horizontal on the screen. Then
use 2-Point rotation to rotate the design to match the quilt. Position the machine’s needle
along the angled sashing seam line and select 2-Point Start. Move the machine’s needle to a
spot along the same seam line and select 2-Point End. The design rotates to match the angle
you defined.
To fine tune the angle of rotation
•
Redefine either the start point or the end point as necessary by moving the quilting machine to a
new location and pressing either 2 Point Start or 2 Point End, depending on which end of the line
needs to be repositioned.
NOTE: A start point on the left followed by an end point on the right (i.e. a straight line with start
on the left and end on the right) is a 0° rotation, or no rotation. A start point on the right and an
end point on the left (i.e. a straight same line, but with the start and end points reversed) is a 180°
rotation, or in other words, the design will be upside down.
www.HandiQuilter.com
Design Menu | 5.13
Rotation of repeated designs
Repeated designs can be rotated individually or treated as a single design and rotated as a set.
To rotate repeated designs individually
Before rotating, select Single. Then select one of the rotate buttons. Each individual design will be rotated
(or mirrored or flipped).
Rotates repeated
designs individually.
To rotate repeated designs as a group
Before rotating, select Group. Then select one of the rotate buttons. The entire set of repeated designs is
rotated (or mirrored or flipped) as a single entity.
Rotates repeated
designs as a set.
5.14 | Design Menu
www.HandiQuilter.com
Crop Menu
Use Crop menu functions in conjunction with areas. After modifying a design as needed, mark an area that
represents the region to be cropped.
•
Select Design and then Crop.
NOTE: If the Crop panel buttons at the bottom of the screen are grayed out, an area hasn’t yet been
defined. Define the area to be cropped before using any of the Crop functions.
Purple lines show the
star-shaped multipoint area.
Treatment of loose ends
Pro-Stitcher has two ways of handling loose ends, or jump points, that are created from a crop: Open or
Closed.
To perform a tieoff at jump points
•
Choose Open to perform a tieoff at the jump points in a cropped design. Select Tie Off Start and
Tie Off Finish in Settings. For more information about the tieoff settings, see Control how
Pro-Stitcher performs tie-offs in chapter 8, Settings Menu.
To stitch between jump points
•
Choose Closed to stitch along the border of the cropped area between jump points in a
cropped design.
Machine Quilting Tip: To stitch around the cropped area
The Closed option may not stitch the entire area outline. Consider using Trace Outline to
stitch around the perimeter of the area.
www.HandiQuilter.com
Design Menu | 5.15
Crop designs based on areas or start and end points
To crop everything outside the defined area
Turns off any crop adjustments
you’ve made to the design.
•
Crops everything
outside the defined
area.
Select Outside to crop away everything outside the defined Area and keep everything within that
Area.
To crop everything inside the defined area
Crops everything
within the defined
area.
•
Select Inside to crop away everything inside the defined area and keep everything outside the area.
To isolate and crop a portion of a design
Use Crop Start-End in conjunction with New Start/End points (on the Quilt menu) to isolate a part of a
design for quilting. Pro-Stitcher crops any of the design before the start point and after the end point.
1. Load a design, such as the continuous bunny and stars e2e.hqf design.
2. Select Quilt and then New Start/End.
3. Use the slider bars and arrows to change the start and end
points.
5.16 | Design Menu
www.HandiQuilter.com
4. Select Design and then Crop.
5. Select Start-End to crop away the design before the start point
and after the end point. Save the design to a new file name so
you can use it again in the future.
www.HandiQuilter.com
Design Menu | 5.17
Repeat Menu
The Repeat Main function provides several options for repeating a design.
•
Select Design, Repeat, and then Main.
The Repeat Wrapping function provides several options for wrapping, or offsetting, designs. Most of these
options can be done with or without a defined area.
•
Select Design, Repeat, and then Wrapping.
Using a defined area in conjunction with the Repeat options will stretch, skew, or fit the desired number
of repeats within that area. If an area has not been defined, the options to stretch and fit will be disabled
because they require an area to stretch or fit to.
Repeat Main
Horizontal repeat
options: Enter the
number of repeats,
or press the Plus
Sign to increase the
number of repeats
or the Minus Sign to
decrease the number
of repeats.
GAP
To repeat a design
Vertical repeat
options: Enter the
number of repeats,
or press the Plus
Sign to increase the
number of repeats
or the Minus Sign to
decrease the number
of repeats.
Increase or decrease the size of the gap
between repeated designs with the
Distance boxes.
•
Press the Plus Sign (+) to increase the number of times you want to repeat a design. To decrease
the number of repeats that appear on-screen, press the Minus Sign (–).
•
Alternately, tap on the number box and enter the desired number of repeats into the pop-up
number box. Then press Enter.
NOTE: If the repeated design includes jump points, Pro-Stitcher preserves them when you save the
design.
To change the size of the gap between repeated designs
•
Enter a value (in inches) in either the Horizontal Distance box or the Vertical Distance box to
increase the size of the gap between repeated designs. To overlap the designs, enter a negative
value.
5.18 | Design Menu
www.HandiQuilter.com
To stretch a design to fill an area
You can stretch a design to fit either the width or the height of an area.
•
First define an area and then choose either the Stretch Width or the Stretch Height button.
Stretches the
design to fit the
width of the area.
Calculates the
optimal number of
repeats both
vertically and
horizontally.
Stretches the design
to fit the height of the
area.
To calculate the optimal number of repeats for an area
•
Press Fit to have Pro-Stitcher calculate the optimal number of repeats in both height and width.
Add more horizontal or vertical repeats, and then select Stretch Width and Stretch Height to fit
them to the area.
Point 2 Point
Some designs are intended to be linked together horizontally or vertically but must be overlapped for
the start and end points to match up. The Point 2 Point buttons link the start and end points of repeated
designs. The following image shows the design before selecting Point 2 Point.
Aligns horizontally
repeated designs
such that the end
point of the first
design matches
up with the start
point of the next
design.
Aligns vertically
repeated designs
such that the end
point of the first
design matches up
with the start point
of the next design.
To join horizontally repeated designs
•
To link designs horizontally, ensure the start and end points are at the same height, or vertical
coordinate. Then select Horizontal Point 2 Point to align the designs such that the end point of the
first design matches up with the start point of the next design.
www.HandiQuilter.com
Design Menu | 5.19
To join vertically repeated designs
Repeated Baptist
Fan design has been
joined vertically and
horizontally with
Point 2 Point.
•
To link designs vertically, ensure the start and end points are at the same horizontal coordinate.
Then select Vertical Point 2 Point to align the designs such that the end point of the first design
matches up with the start point of the next design.
NOTE: To manually enter a distance value between the designs in either the horizontal or vertical
distance box, you must first turn off Point 2 Point.
Repeat Wrapping
Use the wrapping options in conjunction with repeated designs. The options enable you to shift rows or
columns of repeated designs, or offset the entire design window. Typically you will wrap either a row or a
column, but not both.
•
On the Design menu, select Repeat, then select Wrapping.
Column wrapping
options
Vertical window
wrapping options
Removes all of the
wrapping actions
and resets the
design to its
unwrapped state.
Column wrapping
options
5.20 | Design Menu
Horizontal window
wrapping options
www.HandiQuilter.com
To wrap rows
Shifts every other
row of repeated
designs by half of
the width of the
design.
Shifts every other row
by 1/8 inch to the
right or left.
•
To shift every other row of repeated designs (beginning with the second row) by half of the width of
the design, select the 1/2 button.
•
Select the right arrow button to shift the row to the right by 1/8 inch. Select the left arrow button
to shift the row to the left by 1/8 inch.
•
Or touch the number box under Row and use the number pad to enter a decimal value to offset
rows. For example, to move every other row by one inch to the right, enter 1. To move every other
row by one inch to the left, enter -1. After you select Enter, the rows shift accordingly.
To wrap columns
Shifts every other
column of repeated
designs by half of the
height of the design.
Shifts every other
column by 1/8 inch up
or down.
•
To shift every other column of repeated designs (beginning with the second column) by half of the
height of the design, select the 1/2 button.
•
Select the up arrow button under Column to shift the columns up by 1/8 inch.
•
Select the down arrow button under Column to shift the columns down by 1/8 inch.
•
Or touch the number box under Column and use the number pad to enter a decimal value to shift
columns. For example, to move every other column up by one inch, enter 1. To move every other
column down by one inch, enter -1. After you select Enter, the columns shift accordingly.
www.HandiQuilter.com
Design Menu | 5.21
To horizontally wrap the design window
Choose from the options along the bottom of the screen to specify how to wrap the designs window
horizontally.
•
To shift all rows horizontally by half of the width of the design, select the 1/2 button.
Shifts all rows of
repeated designs by
1/8 inch to the right
or left.
Shifts all rows of
repeated designs by
half of the width of
the design.
•
Select the right arrow button to shift all rows to the right by 1/8 inch.
•
Select the left arrow button to shift all rows to the left by 1/8 inch.
•
Or touch the number box under Window and use the number pad to enter a decimal value to shift
the repeated designs. For example, to move all rows by one inch to the right, enter 1. To move all
rows by one inch to the left, enter -1. When you select Enter, the rows all shift accordingly.
To vertically wrap the design window
Choose from several Window options along the right side of the screen to specify how to wrap the design
window vertically.
Shifts all columns of
repeated designs by
1/8 inch up or down.
Shifts all columns of
repeated designs by
half of the height of
the design.
•
To shift all rows by half of the height of the design, select the 1/2 button.
•
Select the up arrow button to shift all rows up by 1/8 inch.
•
Select the down arrow button to shift all rows down by 1/8 inch.
5.22 | Design Menu
www.HandiQuilter.com
•
Or touch the number box under Window and use the number pad to enter a decimal value to shift
the repeated designs. For example, to move all rows up by one inch, enter 1. To move all rows down
by one inch, enter -1. When you select Enter, the rows all shift accordingly.
To manually wrap the design window
•
To manually reposition the design, choose the Drag button. Use your finger (or move the machine)
to drag the design to your desired wrapping position. The Drag button remains enabled and
displays the word Drop; continue to fine tune by dragging the design. When you are happy with the
wrapping position, select Drop.
Treatment of jump points
Choose between two ways of handling loose ends, or jump points, that are created from wrapping designs.
•
Select Open to perform a tieoff at the jump points in a wrapped design. Tie Off Start and Tie Off
Finish must be selected in Settings. For more information about the tieoff settings, see Control how
Pro-Stitcher performs tie-offs in chapter 8, Settings Menu.
•
Select Closed to stitch along the border of the area between jump points in a wrapped design.
www.HandiQuilter.com
Design Menu | 5.23
Resize Menu
•
To open the resize options, select Design and then Resize.
Choose one of the
four height and width
buttons and then
press the Plus Sign or
Minus Sign to resize,
or enter a resize value
in the number box.
Height and Width
buttons
Returns the design to its
original size.
Ensures the design’s aspect ratio
remains constant as you adjust
height or width.
To resize a design
•
Click one of the height or width buttons and then press the Plus Sign (+) to increase or Minus Sign
(–) to decrease, or tapping the number box to directly enter the size (in inches).
This width of this
design was increased.
Green line shows the
x-axis, or width of
the design, that the
Width button adjusts.
This height of this
design was increased.
5.24 | Design Menu
Select to adjust the
width of the design.
Select to adjust the
height of the design.
Original Height and
Original Width: Select
to adjust rotated
designs long their
original x and y axes.
Purple line shows the
y-axis, or height of
the design, that the
Height button adjusts.
www.HandiQuilter.com
This original width of
this rotated design
was increased.
Blue line shows the
original x-axis, or
original width of a
rotated design.
Select to adjust
original width.
•
To stretch or shrink the design along the original X axis rather than how it is oriented on the screen,
select the Original Width button (with the blue angled line) and then press the Plus Sign (+) to
increase or Minus Sign (–) to decrease the size of the design.
NOTE: The Original Width and Original Height buttons are accessible only if a design has
been rotated.
This original height
of this rotated design
was increased.
Yellow line shows
the original y-axis, or
original height of a
rotated design.
Select to adjust
original height.
•
To stretch or shrink a rotated design along its original Y axis rather than how it is oriented on the
screen, select the Original Height button (with the yellow angled line) and then press the Plus Sign
(+) to increase or Minus Sign (–) to decrease the size of the design.
www.HandiQuilter.com
Design Menu | 5.25
Skew / Align Menu
After you create an area, use the skew and align options to fit the design within the area. These options
with convex areas (e.g. triangles, rectangles, and hexagons) of three or more points. Pro-Stitcher does not
skew or align designs to a concave area (e.g. stars and crosses).
•
Select Design and then Skew/Align.
Forces a design to
stretch to fill an area.
Any further actions
will also stretch to the
limits of the area.
Buttons align the
design to the top,
bottom, left, or right
side of an area,
or stretch designs
horizontally or
vertically.
Skew and align
options aren’t
available until you
define an area.
Returns the design to its
original size.
To horizontally align blocks within an area
Align Center: Aligns
the horizontal
center of the design’s
bounding box with
the horizontal center
of the area.
Align Left: Aligns
the left side of the
design’s bounding
box with the leftmost
point of the area
(pictured).
Design bounding box
(blue lines)
Defined area (purple
lines)
Align Right: Aligns
the right side of the
design’s bounding box
with the rightmost
point of the area.
Horizontal Stretch:
Stretches or shrinks
the design so the left
side of the bounding
box aligns with the
leftmost point of the
area and the right
side of the bounding
box aligns with the
rightmost point of the
area.
5.26 | Design Menu
www.HandiQuilter.com
To vertically align blocks within an area
Align Top: Aligns the
top of the design’s
bounding box with
the top of the area
(pictured).
Align Center: Aligns
the vertical center of
the design’s bounding
box with the vertical
center of the area.
Align Bottom: Aligns
the bottom of the
design’s bounding box
with the lowest point
of the area.
Vertical Stretch:
Stretches or shrinks
the design so the top
of the bounding box
aligns with the highest
point of the area and
the bottom of the
bounding box aligns
with the lowest point
of the area.
To align a triangle design
1.
2.
3.
4.
Load a design.
Create a triangle-shaped area using Multi-point.
Select Design, then Skew/Align.
Select the Horiontal Alignment
Align Left button.
www.HandiQuilter.com
Design Menu | 5.27
5. Select the Vertical Alignment
Align Top button.
To skew a design to fit a convex area
1. Load a design and then create
a convex area, such as a
diamond.
2. Rotate the design (Design,
Rotate) to fit the area. This
design was rotated 45 degrees.
3. Choose Design, Skew/Align.
Select Skew.
5.28 | Design Menu
www.HandiQuilter.com
To skew a design to fit a concave area
Pro-Stitcher can skew a design to fit within a a concave area, such as a cross or scalloped border.
1. Create an area that represents
the concave area. This
area maps to a portion of a
scalloped border.
2. Load a design, such as the Crosshatch Square. Rotate, repeat. crop, or resize the
design as desired.
3. Choose Design, Skew/Align.
Select Skew 2. The design will
skew to fit the area.
www.HandiQuilter.com
Design Menu | 5.29
Freehand Menu
Pro-Stitcher can record the movement of the quilting machine. For example, record your own all-over
background designs across the width of the quilt. Or record your signature so you can quilt your
signature into your quilts. This screen also enables you to quickly switch from using Pro-Stitcher to
free-motion quilting.
•
Select Design and then Freehand.
Depending on your Pro-Stitcher configuration, you will see a different screen.
Press to start or end
recording the motion
of the quilting
machine. If you move
the machine before
beginning to record
again, a stitching
line connects where
you previously ended
recording with where
you started.
Clears any designs
from the work area,
as well as any
recorded design.
To use a recorded
design in the future,
save it before
selecting Clear.
Press to resume using
Pro-Stitcher for quilting.
Press to switch from using
Pro-Stitcher to free-motion quilting.
To switch to free-motion quilting
•
Select the Free Motion button and free-motion quilt as desired. When you are ready to once again
quilt with Pro-Stitcher, select Engaged.
Record the movements of your freehand quilting
To record freehand motion
•
Select Record or press the star button on the Infinity handlebars. Begin quilting the design you want
to record. When complete, select Stop or press the star button on the handlebars again. Save the
design to the computer (select File, then Save).
5.30 | Design Menu
www.HandiQuilter.com
Machine Quilting Tip: Add recorded stitching to an existing design
Load a design and position the crosshairs where you want to begin recording freehand
motion. A stitching line connects the end point of the design and the position of the
crosshairs when recording begins.
When adding to an existing design, Pro-Stitcher baselines the design and treats it as a single design when
performing other design functions.
To mark and record straight lines
Mark is similar to Record, but instead of recording continuously as you move the machine, it records a
straight line between each marked point.
1. Move the quilting machine to the point where you want to begin a straight line and select Mark or
press the diamond button on the Infinity handlebars.
2. Move the machine to where you want to end the straight line and select Mark or press the
diamond button again. Continue marking along the line, stitch the line, or save it as a design for
future use.
Machine Quilting Tip: Record stitch-in-the-ditch quilting lines
Move the quilting machine to the beginning of the quilt ditch and select Mark to record the
first point of the line. Then move the machine to another point further down the ditch and
press Mark again. Continue marking points along the ditch to record straight lines between
each marked point. The marked ditch design can then be stitched or saved to stitch at
different places on the quilt.
To add jumps to your recorded design
At any point while recording or marking, insert a jump point into your design.
•
Stop recording or marking, and then select Jump. Continue moving the machine, but no stitch lines
will be recorded until you once again select Record or Mark. Jump lines display as dotted lines.
NOTE: Make sure the Auto Rotate function on the table computer is turned off. This ensures that
the screen functions properly as you record the freehand motions.
www.HandiQuilter.com
Design Menu | 5.31
Reposition Menu
The main way to reposition a design for quilting is to create an area based on your quilt and then to use
the Reposition or Skew/Align tools to position the design relative to that area. However, you can use the
reposition functions even if you haven’t defined an area.
NOTE: You can’t use the Skew and Align functions with the Reposition functions. For example, if
you skew a design to a defined area and then select one of the reposition options, the Skew/Align
settings are turned off (essentially resetting the design to its original shape) and the reposition
action takes place.
Centers the design
at the current needle
and crosshair
position.
The four corner
positioning buttons
position a design
relative to the
crosshairs.
Repositions a design
relative to the Home
location.
Machine Quilting Tip: To quilt a skewed design multiple times
If you want to stitch a skewed design multiple times on the quilt, baseline the design (select
the Baseline button in the lower right corner of the screen) and then reposition the design.
To position a design to the intersection of the crosshairs
•
Move the quilting machine needle to a position on the quilt where the design is to be quilted. If you
positioned the needle at the top-left corner, press the top-left corner button. Pro-Stitcher aligns the
top-left corner of the design with the position of the needle and crosshairs. The bottom-left corner,
top-right corner, and bottom-right corner buttons work the same way.
Positions top-left corner of the
design at the intersection of the
crosshairs.
5.32 | Design Menu
www.HandiQuilter.com
Positions the top-right corner of
the design at intersection of the
crosshairs.
Positions the bottom-right corner
of the design at the intersection of
the crosshairs.
Positions the bottom-left corner
of the design at the intersection of
the crosshairs.
Positions the center of the design
at the intersection of the
crosshairs.
www.HandiQuilter.com
Design Menu | 5.33
To reposition a design based on the Home location
The Home location of a design is the point in the design where x=0 and y=0. It may be the start point of the
design, but other times it may be in the middle or any other point in the design. Some digital designers use
the Home location for positioning.
•
Move the quilting machine needle to a position on the quilt where you want the Home location to
quilt. Press the Home button to reposition the design relative to the Home location.
Machine Quilting Tip: Quickly reposition a design to the crosshair position
Use the Home button as a quick-and-dirty positioning tool. For example, if the design is off
the screen because the quilting machine has been moved to a new location, press Reset to
bring the design closer to the current crosshair position.
NOTE: The Home button is a repositioning tool. Do not select it if the design has already been
positioned at the desired location
To position a design based on the center point
•
Move the quilting machine needle to the center point of the block or other area of the quilt. Press
the Center button to center the design at the current needle and crosshair position.
To position a design’s start point on the quilt
•
Move the quilting machine needle to the point where you want to begin quilting. Press Start Point
to reposition the start point of the design with the current needle and crosshair position.
To position a design’s end point on the quilt
•
Move the quilting machine needle to the point on the quilt where you want the quilting to end.
Press End Point to reposition the end point of the design with the current needle and crosshair
position.
To reposition a design up, down, left, or right
•
To reposition the design a specific amount in any of the four directions, enter a distance (in inches)
in the Nudge number box and then press the appropriate arrow to nudge the design up, down, left,
or right. This is especially useful if you want to nudge the design in minute increments.
5.34 | Design Menu
www.HandiQuilter.com
Machine Quilting Tip: To nudge the design in tiny increments
By default the nudge distance is set to one tenth (.10) of an inch. To nudge the machine in
smaller, more minute increments, change this value to one hundredth (.01) of an inch.
Swap Start/End
There may be times when you want to switch the quilting start and end points, such as when you rotate or
flip a design and the start point is now at the right side of the design. Use the Swap Start/End option to do
this.
To swap the quilting start and end points
End Point
Start Point
1. Load a design.
2. Modify the design as desired.
For example, perhaps you want
this dinosaur design to quilt in
the top border upside down.
3. Choose Design, Swap Start/
End. Then select the Swap
button. The start and end
points will swap places.
New Start
Point
www.HandiQuilter.com
New End
Point
Design Menu | 5.35
5.36 | Design Menu
www.HandiQuilter.com
6. Art & Stitch
Art & Stitch is comprehensive quilting-design software for creating and modifying quilting designs. It is
included with Pro-Stitcher. Pro-Stitcher can pass designs quickly and easily into Art & Stitch so you can
use any of the Art & Stitch tools to modify the design however necessary. Art & Stitch automatically loads
and runs in the background when Pro-Stitcher starts, so passing files from HQ Pro-Stitcher to Art & Stitch
happens very quickly.
To pass a design to Art & Stitch
1. Select Design, and then Art & Stitch. Press Open
screen to open the Art & Stitch software. If Art & Stitch
is open and has been licensed, the design will open in
Art & Stitch.
NOTE: If Art & Stitch has not yet been licensed, a
licensing screen will appear for entering license
information. You will not be able to save any
changes to the design until you activate the
Art & Stitch license. Follow the instructions in
the Art & Stitch instruction manual for
offline activation.
2. Press Close to bypass registration and open the design.
When the design is passed into Art & Stitch, the
position information is maintained; as long as the
design is not moved in Art & Stitch, it will be in the
same location when it is passed back to Pro-Stitcher.
Pass the modified design back to Pro-Stitcher by
pressing the Pro-Stitcher button on the Art & Stitch
toolbar on the left-hand side of the Art & Stitch
screen.
UU CAUTION: If a design is opened in Art & Stitch without using the Pro-Stitcher software and the
Pro-Stitcher button is pressed to pass the design into Pro-Stitcher, the design will be saved in its
current state with the same name it had when it was opened. This could lead to unintentionally
www.HandiQuilter.com
Art & Stitch | 6.1
writing over a design. To avoid this, always save the design with a new working name when it is
directly loaded in Art & Stitch.
Licensing
When using Art & Stitch for the first time, the quilter must enter some information to activate the license.
Refer to the instructions in the Art & Stitch software box for offline activation. All network connections
have intentionally been disabled on the Pro-Stitcher computer to prevent the computer from downloading
updates or viruses that would adversely affect the performance of Pro-Stitcher.
Using a mouse or keyboard
Touch the gray bar
to open the pop-up
keyboard.
Press to close the
keyboard.
Use these buttons
to keep track of
changes you make
to the design.
Many functions in Art & Stitch are much simpler when using a mouse and keyboard. When using the
pop-up keyboard, it may be necessary to press an area on the screen where the text is to be entered
before typing on the keyboard. While the pop-up keyboard is a quick keyboard solution, it may be more
convenient to use a conventional mouse and keyboard. The Pro-Stitcher computer works with most wired
and wireless USB keyboards and mice. Just plug the keyboard, mouse, or wireless dongle into an available
USB port, wait a minute for Windows to install appropriate drivers, and then use the keyboard or mouse. A
USB hub may be used to expand the number of available USB ports. Keyboards, mice, and USB hubs can be
purchased from most electronics retailers.
Updating Art & Stitch
Art & Stitch may need to be updated to the latest version for Pro-Stitcher to properly pass designs back and
forth. To download the latest version, use a computer that is connected to the Internet and go to the Handi
Quilter website: (www.HandiQuilter.com).
To update Art & Stitch
1. Select Downloads and then Pro-Stitcher Software Update. Follow the instructions to download the
latest version of Art & Stitch for Pro-Stitcher. After downloading this installation file, copy it to a USB
flash drive and plug it into the HQ Pro-Stitcher computer.
2. Wait approximately 10 seconds for the Pro-Stitcher computer to set up the USB flash drive. Then select
Design, File, and press Update.
3. Browse to the appropriate folder on the USB flash drive and double-tap the Art & Stitch installation file.
The Pro-Stitcher software will close and the installation will begin.
6.2 | Art & Stitch
www.HandiQuilter.com
4. If you are prompted to Repair or Uninstall the Art & Stitch software, it is best to uninstall first and then
run the installation program again to install the new version.
NOTE: To access the file browser after the Pro-Stitcher software is closed, either attach a keyboard
or press the keyboard icon at the top left-hand corner of the screen to open the pop-up keyboard.
Press and hold the Windows key followed by the letter E to open a file browser to locate and then
run the Art & Stitch installation file again.
5. After the new version of Art & Stitch is installed, reboot the Pro-Stitcher computer using the Windows
Start menu from the bottom of the computer screen. Select either Shut Down or Restart to shut the
computer down and restart.
www.HandiQuilter.com
Art & Stitch | 6.3
6.4 | Art & Stitch
www.HandiQuilter.com
4. HQ Pro-Stitcher® Overview
HQ Pro-Stitcher runs on a touch screen computer with Microsoft® Windows 8 operating system. Because
Pro-Stitcher runs in a Windows environment, you may notice things such as the Windows desktop. If you’re
unfamiliar with the Windows operating system or computers in general, you’ll benefit by taking a class or
finding other ways to learn more about the basics of Windows 8.
To maintain the integrity of the Pro-Stitcher software, avoid using the Pro-Stitcher tablet computer except
when running Pro-Stitcher. For example, if the computer is connected to the Internet, Windows may
perform operating system updates that could potentially be incompatible with Pro- Stitcher. It also may
expose the computer to viruses and other malware that may compromise the system or lead to other
problems that may not be covered by the warranty.
To get the most from using Pro-Stitcher, Handi Quilter recommends using the Pro-Stitcher computer only as
directed to run the Pro-Stitcher software, the Art & Stitch software, the Infinity console software, and other
software provided by or recommended by Handi Quilter.
Enable or disable the carriage motors
Press to lock the
motors in position
and keep the
machine from
moving.
Press to be able to
move the machine
around.
Press to reestablish
communications with
the motors.
The Enable Motors button (top-right corner of the screen) enables you to switch between locking the
motors in position and allowing the machine to be moved around manually. If this button becomes gray
with a lightning bolt, Pro-Stitcher is not communicating with the carriage motors. Press the button to
reestablish communications with the motors. Refer to the Troubleshooting section of this manual for
further help.
www.HandiQuilter.com
Overview | 4.1
Overview of the HQ Pro-Stitcher screen
The Pro-Stitcher screen provides quick access to all functions.
Tap the gray bar to open the
on-screen keyboard.
Press any menu
heading to reveal the
available functions.
Design size
in inches
Name of current
design file
Position of the
needle, or how far
away from the
Home position
(x=0 and y=0) in
the design
Menu options
The left side of the screen shows the available menus: Design, Quilt, Settings, and Shut Down. The
functions for these menu options are described later in this manual. At times there may be more functions
available than can be displayed on the screen. To scroll through the functions, touch the function list and
drag your finger upward to slide the list up and reveal what is at the bottom. Touch and drag downward to
scroll back up to the top of the list.
Panel buttons
Select a main menu
option to see options
for that function.
Buttons appear at
the bottom and right
sides of the screen
according to which
function is selected.
4.2 | Overview
Buttons for repeating
designs horizontally
Buttons for repeating
designs vertically
www.HandiQuilter.com
Work Area
The work area is the portion of the screen where you will load designs and work with them, in preparation
for quilting.
Size of current design
The work area shows
the current design.
Design bounding box
(blue)
Area (purple)
displays if an Area
has been defined.
Crosshairs show the
position of the
machine’s needle.
The crosshairs represent the position of the quilting machine’s needle relative to the current design and
will move as the quilting machine is moved when the carriage is engaged. For more information about how
to engage the carriage, see Freehand Menu in chapter 5, Design Menu.
The size of the bounding box is the width and height of the widest and highest points of the current design.
Jump (dotted line)
Stitching start point
Stitching end point
Jump start and end points
A large green circle on the loaded design indicates the start point, a large red circle indicates the stop point,
and the small green and red circles indicate the start and end points of jumps within the design. Purple
dashed lines connect the small green and red circles to show the jumps, or no-stitch, lines.
www.HandiQuilter.com
Overview | 4.3
Selected vs. non-selected buttons
Some buttons (such as Grid and Ruler) are on/off, or toggle, buttons. Turn them on or off by touching them.
Other buttons are either/or buttons and are turned off by selecting another button with the opposite
action (such as Pan and Drag).
Help button
The Grid and Ruler
buttons are toggles.
Press to turn on or
off.
The Pan, Zoom, Drag,
and Select buttons
cannot be selected at
the same time.
Selected buttons and
menu options are a
darker color.
A gray button means
the function is not
currently available.
Gray Buttons
Depending on the menu or sub-menu item selected, there may be certain buttons that are grayed out. A
gray button indicates that this function is not currently available. This typically happens because you have
started a function that must be completed first or that the grayed-out function is not possible within the
selected function.
Top toolbar buttons
Commonly used functions are across the top of the screen for easy access. They are available regardless of
which menu option you have chosen.
Design size in inches
Name of current design file
Position of crosshairs
Also visible at the top of the screen are the name of the current design file, the size of the design, and the
position of the crosshairs. A letter appears next to the name of the current design file to indicate what
type of design it is: (D) indicates it is a design; (G) indicates it is a grouped design; and (R) indicates it is a
repeated design.
4.4 | Overview
www.HandiQuilter.com
To get on-screen help
Press to close any
pop-up box, such as
a Help box
•Press Help and then press the button or menu option for which you need help to display the Help
pop-up box. Exit Help mode by pressing the Help button again or pressing the Close button (red X).
To cycle the needle up or down to form a half stitch
The Half Stitch button cycles the needle either to the up or the down position based on the current
position of the needle.
•
Tap Half Stitch once to cycle the needle a half stitch.
To cycle the needle to the up position
The Full Stitch button cycles the needle a full stitch to the up position. If the needle is in the down position,
it will move only a half cycle so it stops in the up position. Subsequent presses of the button, however, will
cycle a full stitch, always ending with the needle in the up position.
•
Tap Full Stitch once to cycle the needle a full stitch.
To display the on-screen grid
•Press Grid to turn the grid on or off.
Depending on the zoom level, the lines may indicate either one-inch or one-quarter inch gradations.
www.HandiQuilter.com
Overview | 4.5
Zoomed in
Darker lines show one-inch divisions
and faded lines show one-quarter inch
divisions.
Zoomed out
Lines show one-inch divisions, but no
quarter-inch divisions.
To quickly position the design and crosshairs on the screen
The Refresh button centers the design and crosshairs so both are visible on the screen. Refresh does not
reposition the design relative to the quilt.
To move the on-screen view
Use Pan to move what you see on the work area. Pan does not reposition the design relative to the quilt.
•Select Pan and then drag your finger across the screen. The current view moves with the movement
of your finger.
To view the design larger or smaller
Use Zoom to view the design larger or smaller. Zoom does not reposition or resize the design. If you have
grid lines displayed on-screen, you’ll see the grid lines also shrink or grow as you zoom the design.
•To shrink the view of the design, select Zoom and then drag your finger in a downward or right-toleft motion. To enlarge the view of the design, select Zoom and drag your finger in an upward or
left-to-right motion.
To move the design on the screen
•Select the design and press Drag. After pressing Drag, the button changes to Drop. Touch the design
with your finger and drag the design to a new location. Then press Drop when the design is in place.
•Alternately press Drag and move the quilting machine to move the design. Then press Drop when
the design is in place.
4.6 | Overview
www.HandiQuilter.com
To select one or more designs
•Press Select to select one or more design in the work area. A series of buttons appears for selecting
one or more design.
After you select a design, its name appears at the top of the screen.
Choose All to select
all designs or
None to cancel any
selections.
Selected designs
appear in black with
a blue bounding box
around them.
The checkmark next
to the design name
indicates it is
selected.
To select a single design
•Select Single to select one design at a time. Touch any design in the work area or choose the name
of the design from the pop-up that appears.
Pro-Stitcher displays selected designs with black lines in the work area. Designs that aren’t selected designs
appear with gray lines.
To choose and group multiple designs
•Select Multi to select multiple designs. Then touch each design in the work area that you want to
include in a grouped design. Then select Group to treat the selected designs as if they were a single
design.
Pro-Stitcher gives the group a name and a number and displays the selected group in black with a bounding
box around it. If you have created multiple groups, select the Group button and choose the group you want
to work with from the pop-up box that appears.
If you Baseline a group, the designs are merged and the group is treated as a single design.
After creating a group, you will not be able to work with the designs individually. However, the following
actions may be performed on a Group:
•
Change the stitch order
www.HandiQuilter.com
Overview | 4.7
•
•
Give the group a name
Perform actions such as Rotate, Align, Skew, and most other Design and Stitch menu options.
To name a group
•Select Name to enter a descriptive name for the group to replace the group number assigned by
Pro-Stitcher. Use the keyboard that appears to enter a name and then select OK to save the name
or Cancel to close the name box.
NOTE: If the keyboard opens on top of the box for entering the name, move it by touching the top
area of the keyboard and dragging it to a new location on the screen. Close the on-screen keyboard
or name box by touching the Close (X) button in the upper-right corner. Alternately you can drag
the name box to a new area on the screen in the same way.
To change the stitch order of multiple designs
Choose one or more
design and then
touch the up or down
arrow keys to change
the order they will be
stitched.
•Select Stitch Order to change the order in which the designs in the group are stitched. Choose one
or more design and then touch the up and down arrows to shift the stitch order.
Jump lines between designs change as the stitch order changes.
To measure distances in a design or on the quilt
Use the Ruler to measure distances in a design or directly on the quilt.
1.Move the machine so the crosshairs, or the needle position, are at the starting point, or zero
coordinate, of the section to be measured.
4.8 | Overview
www.HandiQuilter.com
2.Press Ruler and move the machine to begin measuring. The ruler gives you the distance in the
horizontal (x) and the vertical (y) directions, as well as the direct angular distance (represented by
the triangle symbol).
3.Press Ruler again to turn off the ruler. To reset the ruler starting point, press Ruler to turn off the
ruler and then turn it back on after you have moved the crosshairs to where you want to begin
measuring.
Machine Quilting Tip: To measure a dimension longer than the available quilting space
Press Ruler and measure as far on the quilt as you can and mark where you ended with a
pin. Enter the measurement into the calculator on your quilting machine. Press Ruler again
to turn it off. Advance the quilt, making sure the pin is still visible. Press Ruler and measure
the next segment, and use the calculator to add this measurement. Press Ruler to turn it off.
Continue in this manner until you have the total measurement you need.
Crosshairs
The intersection of the horizontal and vertical crosshairs represent the position of the machine’s needle. By
default, the Follow button isn’t selected and the crosshairs move when you move the machine. This means
that the design remains stationary on the screen, but the crosshairs move.
If you select Follow, the crosshairs remain stationary in the middle of the display. As you move the
machine, the design moves rather than the crosshairs.
Machine Quilting Tip: When to use Follow
Select Follow when you want to ensure that the crosshairs remain in view when you have
zoomed a design. This saves you from having to use Pan to find the crosshairs. It is also
helpful to enable Follow when you stitch a wide design because you can both zoom in on
the design and always see what is being stitched on the screen.
Pro-Stitcher automatically turns off Follow after you select a new design.
www.HandiQuilter.com
Overview | 4.9
4.10 | Overview
www.HandiQuilter.com
7. Quilt Menu
The functions on the quilt menu enable you to quilt your designs. The Run button is available to start the
stitching from any quilt function.
Machine Quilting Tip: Set your stitch regulation to Cruise mode
Handi Quilter recommends that before quilting you set the quilting machine to Cruise stitch
regulation mode, at a percentage of 3 to 5%.
•
After the design has been formatted, positioned, and is ready to be stitched, select Quilt and then Run.
If everything looks good, press Proceed to begin stitching. Otherwise, press Cancel.
Brings the quilting
machine to an
immediate stop and
disables motors.
If you selected the option to Verify Settings before Quilting in the quilt settings, a pop-up Verify Settings
box appears so you can double check the settings before stitching. For more information about turning on
or off this option, see To verify settings before quilting in chapter 8, Settings Menu.
To choose between stitching or tracing the design, bounding box, or area perimeter
•
Make sure the Stitch button is enabled (shown in a darker color) for the machine to stitch the quilt
according to the selections you make. To disable stitching, press the darkened Stitch button. If the
Stitch button is disabled, Pro-Stitcher traces the design, bounding box, or area perimeter with the
machine but does not stitch. Select the Stitch button again to enable stitching.
To immediately stop the machine from quilting
•
If you must immediately stop the machine while quilting, press Emergency Stop. Unlike Pause,
which brings the machine to a gentle stop, the Emergency Stop button immediately stops ProStitcher. To reduce the risk of a torn quilt in case the needle is stuck, Pro-Stitcher also disables the
motors.
www.HandiQuilter.com
Quilt Menu | 7.1
Before you stitch the design on the quilt
Before stitching any design, it’s a good idea to double check the position of the design relative to the quilt.
Machine Quilting Tip: Verify the position of the design relative to the quilt
Move the quilting machine needle to a location on the quilt. Select the Follow button in the
top-right corner of the screen so the design will move as you move the machine. Look at the
screen and confirm that the crosshairs match the desired position in the design. Do this for
a variety of places on the quilt, such as the start and end points and the highest and lowest
points in the design.
In addition to doing a manual check, use the two Trace options to verify the position of the design’s
bounding box or the defined area relative to the quilt.
The design’s bounding
box
A dot indicates
the start point for
the area.
To verify the position of the design’s bounding box on the quilt
•
Select Trace Box and then Run. Pro-Stitcher moves the machine around the perimeter of the
design, following the blue bounding box. Watch the needle position as the machine traces the
design’s bounding box to ensure the design will quilt where expected. If the Stitch button is enabled
(appears darker), Pro-Stitcher stitches, rather than traces, the bounding box.
To verify the position of the defined area on the quilt
•
Select Trace Area and then Run. Pro-Stitcher moves the machine around the perimeter of the
defined area, shown as purple lines on the screen. Watch the needle position as the machine traces
the area’s perimeter to ensure the design will quilt where expected. If the Stitch button is enabled
(appears darker), Pro-Stitcher stitches, rather than traces, the perimeter of the area.
NOTE: If you’ve enabled the Stitch button to stitch rather than trace the bounding box or the
perimeter of the area, you must manually do tieoffs at the beginning and end of stitching.
7.2 | Quilt Menu
www.HandiQuilter.com
Move the quilting machine with Pro-Stitcher
The Move function moves the quilting machine in any of the eight directions indicated by the on-screen
arrows.
Control the speed by
pressing either the
Plus Sign or the Minus
Sign, or entering a
value (up to 50) in the
number box.
Press and hold one of
the arrow keys to move
the machine in that
direction.
Select Stitch to stitch
as the machine moves.
Select Continuous and select an arrow key
to move the machine. Press Stop to end
movement or stitching.
To change the speed at which the machine moves
•
Tap the Plus Sign (+) to increase the movement speed. Tap the Minus Sign (–) to decrease the
movement speed. Or select the number box and enter a value (up to 50) in the number pad that
appears and then press Enter.
To move the quilting machine from within Pro-Stitcher
•
Press and hold an arrow button. The selected arrow button changes to a Stop button. The machine
moves in the selected direction until you stop pressing the arrow key.
•
Alternately, select Continuous. Then press (and release) an arrow key. The selected arrow button
changes to a Stop button. The machine moves in the selected direction until you press the Stop
button.
To stitch a straight line using the Move buttons
•
Select the Stitch button. Press and hold an arrow button. The selected arrow button changes to a
Stop button. The machine stitches a line in the selected direction until you stop pressing the arrow
key.
•
Alternately, select both Stitch and Continuous. Then press (and release) an arrow key. The selected
arrow button changes to a Stop button. The machine stitches in the selected direction until you
press the Stop button.
Machine Quilting Tip: Straight-line quilting
Use the Move and Stitch options to stitch straight lines for stitch-in-the-ditch, piano-key
borders, and cross-hatching. Use the down arrow with stitch to baste down the right and
left sides of the quilt. If you also select Continuous, you will be able to use both hands on
the quilt to ensure that the quilt top and edges lay flat against the batting.
www.HandiQuilter.com
Quilt Menu | 7.3
Pro-Stitcher as a horizontal or vertical channel lock
If you use the channel lock feature in Pro-Stitcher, you will be able to stitch horizontal and vertical lines that
are perfectly square with Pro-Stitcher and the frame.
To stitch a horizontal or vertical line with the channel lock
•
Select Horizontal Channel Lock to lock Pro-Stitcher so it stitches only in a horizontal direction.
Press the Start/Stop button on the machine’s handlebars and move the machine to stitch the line in
a left-to-right or right-to-left direction.
•
Select Vertical Channel Lock to lock Pro-Stitcher so it stitches only in a vertical direction. Press the
Stop/Start button the machine’s handlebars and move the machine to stitch the line in a top-tobottom or bottom-to-top direction.
ÂÂ IMPORTANT: Ensure that the carriage motor levers are in the engaged position. You can then
manually use the quilting machine handles to stitch either horizontal or vertical lines.
Machine Quilting Tip: To stitch a plumb line with Pro-Stitcher
Ensure your quilt top is loaded squarely on the frame by stitching a horizontal plumb line
across the top of the batting and backing. Select Horizontal Channel Lock, press the Start/
Stop button on the machine’s handlebars, and stitch a plumb line approximately one inch
from the top of the quilt backing and batting. Then align the top edge of the quilt top with
the plumb line and baste close to the edge so the stitching will be covered by the quilt’s
binding.
ÂÂ IMPORTANT: If you use an HQ Sixteen with Pro-Stitcher, switch to manual control before using the
handlebars.
Adjust settings while quilting
While the machine is stitching, you can adjust several quilting settings, such as speed, auto jump, stitches
per inch, tieoff, pullup, and pause delay. For more information about quilt settings, see chapter 8, Settings
Menu. You can also adjust the most commonly used settings directly on the Stitch screen.
7.4 | Quilt Menu
www.HandiQuilter.com
Adjust commonly used
settings just before
quilting if necessary.
Select the Stitch
button to stitch the
design on the quilt.
Disable the Stitch
button to trace
the design without
stitching.
To adjust commonly used stitch settings
•
Select Quilt and then select Stitch on the menu. Turn on or off the starting or ending tieoffs and
choose how to do pullups. For more information about tieoffs and pullups, see Control how ProStitcher performs tie-offs in chapter 8, Settings Menu. You can adjust these settings while quilting or
after quilting is paused.
NOTE: If you disable the Stitch button, the tieoff and pullup options are also turned off. If you select
either the Tie Off or Pullup option, the Stitch button is automatically selected.
To adjust the quilting speed while quilting
Cancels stitching after
pausing
Resumes stitching after
pausing
•
Change stitching
speed on the fly –
even while stitching.
Choose Slow, Medium, or Fast to control the stitching speed, or drag the scroll bar to your desired
quilting speed. For more information about the quilting speed setting, see Control how fast ProStitcher operates in chapter 8, Settings Menu.
To adjust the auto jump threshold while quilting
A jump is a gap in a design where there is no stitching. If a jump is less than the threshold, Pro-Stitcher
does not pause for you to cut the thread. If a jump is greater than the threshold, Pro-Stitcher pauses for
you to cut the thread. For more information about the auto jump threshold, see Control how Pro-Stitcher
handles jumps in chapter 8, Settings Menu.
www.HandiQuilter.com
Quilt Menu | 7.5
Change the auto jump
threshold by entering
a number or using the
Plus Sign to increase
or the Minus Sign to
decrease.
•
Select the Auto Jump box to specify the maximum length (in inches) of a jump, or gap in a design
path. A number pad appears on the screen for you to enter the number, then press Enter.
Alternately, use the Plus Sign (+) to increase or Minus Sign (–) to decrease the number.
To adjust stitches per inch while quilting
Change the number
of stitches per inch by
entering a number or
using the Plus Sign to
increase or Minus Sign
to decrease.
•
Enter the number of stitches per inch for quilting the design. A number pad appears on the screen
for you to enter a number, then press Enter. Alternately, use the Plus Sign (+) to increase or Minus
Sign (–) to decrease the number.
Machine Quilting Tip: The best stitches per inch setting for your design
Smaller designs, especially designs that have lots of curves and circles, may require a shorter
stitch length, such as 12 to 18 stitches per inch. Less intricate designs with large curves or
circles can use a larger stitch length, such as 10 stitches per inch.
To manage the tieoff settings while quilting
Indicate how to tie off the stitching at jump points and at the start and end of a design. For more
information about the tieoff settings, see Control how Pro-Stitcher performs tie-offs in chapter 8, Settings
Menu.
7.6 | Quilt Menu
www.HandiQuilter.com
Select to tie off at the
end of stitching.
Select to tie off at the
beginning of stitching.
•
Choose whether to
tie off with a tacking
stitch or with micro
stitches.
Choose Tie-Off Start or Tie-Off End to indicate your preference for tieoffs. Choose whether to use a
tacking stitch or micro stitches for the tieoffs. If you do not select either tieoff option, you will need
to manually do the tieoffs.
To change the thread pullup settings while quilting
Indicate how to pull up the bobbin thread before quilting a design. Pull-up On brings up the bobbin
thread and disables the motors for you to move the machine and pull up the bobbin thread. Pull-up Auto
brings up the bobbin thread and then automatically moves the machine aside and pauses for you to grab
the threads. In each case, press Resume to continue after grabbing the threads. For more information
about the pullup options, see Control how Pro-Stitcher handles bobbin-thread pullups in chapter 8,
Settings Menu.
•
Choose Pull-up On or Pull-up Auto to indicate your preference for handling pullups. If you do not
select either pullup option, you will need to manually pull up the bobbin thread before stitching.
To change the pause delay settings while quilting
After beginning to stitch and following a pullup, Pro-Stitcher does some stitches and then pauses for you
to cut the threads. The pause delay setting indicates how much stitching to do, measured in either inches
or seconds, before pausing. For more information about the pause delay options, see Control the delay
following a bobbin-thread pullup in chapter 8, Settings Menu.
www.HandiQuilter.com
Quilt Menu | 7.7
Turns off the pause
delay setting.
•
Choose Seconds or
Inches and then enter
a value in the number
box to specify how
much Pro-Stitcher will
stitch before pausing
for you to trim the
threads.
Specify how far or how long Pro-Stitcher will stitch before pausing for you to trim the threads.
Choose either Seconds or Inches. Then touch the number box, enter a number into the number pad
that appears, and then press Enter.
Adjust settings while quilting is paused
On occasion you may need to pause stitching to make further adjustments to settings, to replace a bobbin,
or rethread the machine. You can change any of the settings described in the previous section while the
machine is paused. However, after pausing the machine, other options are also available: stitch, reposition,
status, and new start/end.
To pause quilting
•
Press the Pause button for the machine to come to a gentle stop. Pro-Stitcher places gold marker at
the point in the design where you paused. To make changes to settings, select Quilt and then select
Reposition, Status, or New Start/End.
Reposition designs while quilting is paused
At any point after pausing the quilting, you can reposition the design based on the start point or end point.
•
After pausing the quilting, select Quilt, then select Reposition.
To reposition the design while quilting is paused
The Current Point function is available only during a Pause. The Current Point is the point in the design
where the Pro-Stitcher paused the stitching. It is marked with a gold marker.
7.8 | Quilt Menu
www.HandiQuilter.com
•
Move the machine and crosshairs to the desired location and press the Current Point button under
Reposition. If the Start Point has been altered during a Pause, pressing Resume will cause the ProStitcher to resume from the adjusted Start Point rather than the Current Point.
To see how far into a design the machine has stitched
After pausing the quilting, select Quilt and then select Status. Pro-Stitcher displays the line segment being
stitched and the distance traveled (in inches).
Select Status to display
the line segment being
stitched and the
distance traveled
(in inches).
The current point
marker shows where
stitching was paused.
Machine Quilting Tip: Using the line segment and distance information
The line segment information is useful if you want to resume quilting from that exact point,
such as when you are quilting over-sized blocks and need to roll the quilt after quilting part
of the block. Make a note of the line segment and distance values so that you can begin
quilting again at that precise location.
The distance information may be useful in determining how much thread has been used.
Change the start or end point of a design
After the thread breaks or the bobbin runs out of thread, you may need to start quilting from a point other
than the design’s start point. Similarly, you may want to change the end point to a point other than the
design’s original end point and quilt only a part of the design.
www.HandiQuilter.com
Quilt Menu | 7.9
Drag the top scroll bar
to move the start point
to a new position in the
design.
Drag the bottom
scroll bar to move the
end point to a new
position in the design.
To begin quilting from a point other than the design’s start point
•
Position the needle where you want to begin stitching and select Start Auto. The point in the design
that is closest to the crosshairs will be the new start point. Alternately, drag the top scroll bar to
move the start point to a new position in the design.
To end quilting at a point other than the design’s end point
•
Position the needle where you want to end stitching and select Stop Auto. The point in the design
that is closest to the crosshairs will be the new end point. Alternately, drag the bottom scroll bar to
move the end point to a new position in the design.
NOTE: If you select a start point that is beyond the current end point in the design, the end point is
adjusted to follow the start point. Similarly, if you select a end point that is before the current start
point in the design, the start point is adjusted to come before the end point.
NOTE: If the Start Auto or Stop Auto buttons are selected, the start or end points continue to move
as you move the machine and crosshairs.
To adjust start and end points with the scroll bars
The upper scroll bar controls the start point and the lower scroll bar controls the end point.
•
Use the left and right arrows at the ends of the scroll bars to fine tune the selection to precisely
position the new start or end point.
To set a start or end point to a jump point in the design
•
For designs that have multiple jump points, press the Jump Point arrows to move either the start or
end point to the next jump point in the design.
7.10 | Quilt Menu
www.HandiQuilter.com
Machine Quilting Tip: Recovering from a thread break or bobbin change
If the thread breaks while stitching, press Pause. Fix the problem by rethreading the
machine or changing the bobbin. Select the Quilt menu and then select the New Start/
End function. Then press the Start Auto button. Press Disable Motors. Move the machine’s
needle to the place on the quilt where you want to begin stitching again. The crosshairs
on the screen will move to the corresponding position on the design. If some fine tuning is
needed to move the new starting point forward or back in the design, use the left or right
arrows on the scroll bar until the new start point is exactly where desired. Press Start Auto
again. Use the Half Stitch button to pull up the bobbin thread. Press the Tie off on Resume
and Pullup on Resume buttons to disable. Press Resume to continue quilting.
If the quilt has shifted slightly and the point on the design does not match up exactly with
the point on the quilt, move the needle to the exact location on the quilt that matches the
new starting point that was just set. Then select Reposition on the Quilt menu and press
Start Point. The design shifts to align the new start point with the current needle position.
Double check the Tie Off and Pullup settings and press Resume to continue stitching
the design.
www.HandiQuilter.com
Quilt Menu | 7.11
7.12 | Quilt Menu
www.HandiQuilter.com
8. Settings Menu
Before stitching any design, it is always a good idea to double-check the settings. Some quilters may find
settings that will work for everything they do and never go back to change them. However, most will likely
find that different projects will require different settings. Make a habit of checking these settings before
quilting any design.
Control how fast Pro-Stitcher operates
The Speed setting sets how fast the Pro-Stitcher carriage will move through the quilting design.
Because the quilting machine regulates its own speed to maintain a specific stitches-per-inch setting,
the speed does not directly set the needle speed. Instead it sets how fast the machine moves across
the frame system.
•
Select Settings, Speed.
To set the default speed
•
Choose either the Slow, Medium, or Fast button to set the default speed.
•
Alternately, use the scroll bar to select a speed between the slow, medium, or fast settings.
Control how Pro-Stitcher handles jumps
If a quilt design contains jumps, or gaps, in the design path that are not stitched, Pro-Stitcher can either
move automatically without stitching through the jump point and begin stitching at the end of the jump or
it can pause before the jump so you can trim the thread before it moves to the next starting point.
•
Select Settings, Auto Jump.
Machine Quilting Tip: Avoid long jumps
The longer the jump, the more likely the thread will break or the quilt will gather or become
distorted as the machine pulls the thread to the next start point. Set an Auto Jump threshold
that is an appropriate number of inches so both your quilt and quilting remains smooth.
www.HandiQuilter.com
Settings Menu | 8.1
To set the Auto Jump threshold
•
Press the Plus Sign (+) to increase or Minus Sign (–) to decrease the Auto Jump threshold by .5 inch.
Alternately, touch the number box and type a value directly and press Enter.
NOTE: If the jump distance is less than the Auto Jump threshold (number of inches entered in the
Auto Jump box), Pro-Stitcher does not pause for you to trim the thread before jumping to the next
start point. If the jump is longer than the Auto Jump threshold, Pro-Stitcher pauses before the jump
so you can trim the thread.
NOTE: If Tie Off options are turned on, Pro-Stitcher performs a tie off at the jump start and end
points, regardless of which jump method is performed. If the Pullup feature is turned on,
Pro-Stitcher performs a pull up at the end of the jumps that exceed the Auto Jump threshold.
Control the number of stitches per inch
•
Select Settings, Stitches Per Inch.
To set the stitches per inch
•
Press the Plus Sign (+) to increase or Minus Sign (–) to decrease the stitches per inch. Alternately,
touch the number box and type a value directly and press Enter.
8.2 | Settings Menu
www.HandiQuilter.com
Control how Pro-Stitcher performs tie-off stitchess
By tieing off at the beginning and ending of stitching, the stitches will be secure and will not come
undone. The tie-off feature enables you to select your preferred method for how and when Pro-Stitcher
performs tie-offs.
•
Select Settings, Tie Off.
Select Tie-Off End
to perform a tie-off
at the end of each
segment in the design.
Select Tie-Off Start to
perform a tie-off at
the beginning of each
segment in the design.
Specify how many tieoff stitches are done.
Specify the length
of tie-off stitches in
inches.
Choose either the Tack
or Micro method of
tie-off.
To have Pro-Stitcher perform a tieoff at the beginning of stitching
•
Select Tie-Off Start.
To have Pro-Stitcher perform a tieoff at the end of stitching
•
Select Tie-Off End.
To indicate how many tie-off stitches Pro-Stitcher will perform
•
Press the Tie-Off # Plus Sign (+) to increase or Minus Sign (–) to decrease the number of tie-off
stitches Pro-Stitcher performs. Alternately, touch the number box and type a value directly and
press Enter.
NOTE: The number you specify is the number of full stitches that are formed, not the number
of times the needles cycles. For example, if the tie-off number is set to 2 and you selected the
Micro method, the needle cycles three times before beginning to stitch the design. Alternately, if
you selected the Tack method, the needle cycles five times to form two stitches forward and two
stitches back.
To set the length of each tie-off stitch
•
Press the Distance Plus Sign (+) to increase or Minus Sign (–) to decrease the distance in inches for
each tie-off stitch. Alternately, touch the number box and type a value directly and press Enter.
www.HandiQuilter.com
Settings Menu | 8.3
To select the method of tie-off stitch: Micro or Tack
•
Press Tack to select the Tack method of
tie-off. The Tack method forms the selected
number of stitches forward into the design
and then back to the start point before
beginning to stitch the design, thus doubling
the number of stitches selected.
•
Press Micro to select the Micro method
of tie-off. The Micro method forms the set
number of tie-off stitches forward into the
design and then begins stitching from there.
When stitching the design is coming to an
end, Pro-Stitcher stops stitching just before
the end point and performs the selected
number of tie-off stitches to the end of the
design. This method does not back over
itself and is more likely to be pulled loose
than the Tack method. However, it is much
less noticeable than the Tack method
because there is no build-up of thread.
Control how Pro-Stitcher handles bobbin-thread pullups
Pro-Stitcher can be set to automatically pull up the bobbin thread at the start of stitching a design. It can
pull up the thread and automatically shift aside for you to grab the threads or it can pull up the thread and
enable you to manually move the machine aside to pull up the thread.
•
Select Settings, Pullup.
To turn on bobbin-thread pullups
•
Press Pull-Up On for Pro-Stitcher to perform a pull up at the beginning of the design and at the
beginning of each segment following a jump that exceeds the Auto Jump threshold.
8.4 | Settings Menu
www.HandiQuilter.com
To turn on automatic bobbin-thread pullups
•
Press Pull-Up Auto for Pro-Stitcher to shift the quilting machine to the right a few inches after
pulling up the bobbin thread so you can grab both threads. Press Resume to continue quilting the
design.
NOTE: If Pull-Up Auto is not selected, but Pull-Up On is selected, the quilting machine will take a
stitch at the start point and then disable the motors. This enables you to manually push the quilting
machine aside to pull up the bobbin thread. Press Resume for the machine to move back into
position and resume quilting.
Control the delay following a bobbin-thread pullup
The Pause Delay feature pauses the quilting machine shortly after starting into a design and after each time
a pullup is performed. This enables you to safely trim the thread tails.
•
Select Settings, Pause Delay.
To set the Pause Delay
•
Select On to turn on Pause Delay or Off to turn off Pause Delay.
You have the option of setting the Pause Delay in seconds (how long of a delay) or inches (how far it
stitches before pausing).
To set Pause Delay in seconds
•
Select Seconds and then press the Plus Sign (+) to increase or Minus Sign (–) to decrease the
number of seconds for the pause. Pro-Stitcher will pause the number of seconds indicated so you
can trim thread tails and then resume stitching.
To set Pause Delay in inches
•
Select Inches and then press Plus Sign (+) to increase or Minus Sign (–) to decrease the number
of inches Pro-Stitcher stitches before pausing. Press Resume after trimming thread tails to
continue stitching.
www.HandiQuilter.com
Settings Menu | 8.5
Advanced Menu
The Advanced Menu contains options that you will rarely need to use. Many are used by HQ Technical
Support as they help to diagnose any issues you may experience with Pro-Stitcher.
General Options
•
Select Settings, Advanced, General.
To create a simulation license
You can create a simulation version of Pro-Stitcher which enables you to use the Pro-Stitcher software in
simulation mode on any computer running Microsoft Windows 7 or 8. It also runs on the Pro-Stitcher tablet
itself when not attached to the quilting machine. Using a simulation license enables you to take the tablet
computer or a notebook computer to Pro-Stitcher training and use the software functions even though the
computer isn’t attached to a quilting machine.
1. Download the latest version of the Pro-Stitcher software, for example
PSUpdate15.04.0071.exe, to a USB flash drive.
ÂÂ IMPORTANT: If this version isn’t already installed on your Pro-Stitcher tablet,
install it by inserting the USB flash drive into the tablet computer. After the tablet
computer accesses the USB drive, follow instructions on the screen for continuing
the installation.
2. Start Pro-Stitcher as usual on the Pro-Stitcher tablet and ensure that it connects with
the carriage motors.
NOTE: If you will be running Pro-Stitcher in simulation mode from the tablet
computer, installation is complete. If you will be running Pro-Stitcher in
simulation mode on a different computer, continue with the remaining steps.
ÂÂ IMPORTANT: You must have adminstrator rights for the Windows computer you
will use for the Pro-Stitcher simulation.
8.6 | Settings Menu
www.HandiQuilter.com
3. Insert the USB flash drive into a USB port on the Windows computer you will use for
simulation mode.
4. View the files on the USB drive. Right-click the Pro-Stitcher executable file
(PSUpdate15.04.0071.exe, in this example) and select Run as administrator. ProStitcher will install onto the Windows computer and then start up.
5. You will see a pop-up message
asking whether you want to
be able to run Pro-Stitcher in
simulation mode. Select Yes.
If you select No, Pro-Stitcher
will not run.
6. When you receive this
message, do not yet select OK.
7. Remove the USB drive from the Windows computer and insert it into the Pro-Stitcher
tablet computer that is attached to the quilting machine’s carriage.
8. On the Pro-Stitcher tablet, select Settings, Advanced, General. Then select the
Create Simulation License button.
9. When you receive the message
License file written, select OK.
Remove the USB drive.
10. Return to the Windows
computer you will use for
simulation mode and insert the
USB drive back into the USB
port of the Windows computer.
Now select OK
11. You can now run Pro-Stitcher in simulation mode on the Windows computer.
www.HandiQuilter.com
Settings Menu | 8.7
To use the Pro-Stitcher simulation mode
If running the simulation mode on the Pro-Stitcher tablet computer, you may switch between simulation
mode and regular mode. However, when running Pro-Stitcher on a standalone Windows computer, it only
runs in simulation mode.
•
To run Pro-Stitcher simulation mode on the Pro-Stitcher tablet computer, select Settings, Advanced,
General. Select Simulation on/off to alternate between simulation mode and regular mode.
•
To run Pro-Stitcher simulation mode on the Windows computer, simply start Pro-Stitcher.
When Pro-Stitcher is running in simulation mode, a Sim button (for simulation) appears in the upper right
section of the screen and the Follow button is removed.
When the Sim button is selected, the mouse and the keyboard arrow keys simulate moving the quilting
machine to do things such as zoom, pan, or create areas. The other button function as normal. Simply
select them with the mouse.
1. Ensure the Sim button is selected (appears dark green) at the top right of the screen.
2. Use the arrow keys or mouse to simulate moving the quilting machine.
NOTE: Hold the shift key while using the arrow keys for faster cursor movements. You can also hold
the left mouse button and drag the mouse and the cursors will move along with the mouse.
To turn on or off the Thread Break Sensor
•
Press the button next to Thread Break Sensor on/off to turn it on or off. It is on when the button is
dark.
If the thread break alarm is triggered and this option is on, Pro-Stitcher pauses when the thread breaks. If it
is off, Pro-Stitcher ignores the thread break and continues stitching.
To verify settings before quilting
•
Press the button next to Verify Settings Before Quilt to have Pro-Stitcher display a pop-up box with
all of the current settings. This gives you the opportunity to verify that everything is set up properly
before stitching. If you don’t want to see this box, disable the button.
Communications Options
The Communication sub-menu enables you to manually establish communications with either the quilting
machine or the Pro-Stitcher motors.
•
Select Settings, Advanced, Communications
8.8 | Settings Menu
www.HandiQuilter.com
To stop communications between Pro-Stitcher and the quilting machine
•
Press Switch to Handlebar Control. The button changes to say Connect to Pro-Stitcher. To reestablish communications, press Connect to Pro-Stitcher.
To reconnect motors
If the Pro-Stitcher motors ever become unplugged or disconnected from the computer, it may be necessary
to reestablish communications between the Pro-Stitcher computer and the motors.
If the Pro-Stitcher computer cannot communicate with the motors for any reason, it will be indicated by a
lightning bolt icon at the top right-hand corner of the screen.
•
Press Reconnect Motors or the Motor Error button in the top-right corner of the screen to reestablish
communications between the Pro-Stitcher computer and the motors.
To reconnect the machine
You may need to reestablish communications between Pro-Stitcher and the quilting machine. For example,
this happens when you start the Pro-Stitcher computer while the quilting machine is turned off.
•
Press Reconnect Machine to reestablish communications between the Pro-Stitcher and the quilting
machine.
Easily test whether Pro-Stitcher is communicating with the quilting machine by pressing the Full Stitch
button at the top of the Pro-Stitcher screen, or looking at the touchscreen on the quilting machine’s
handlebars. If there is communication between the quilting machine and Pro-Stitcher, the quilting
machine’s touchscreen will indicate it. If they are connected, the quilting machine will cycle the needle.
If they are not communicating, nothing will happen. If the Pro-Stitcher computer can detect that it is not
communicating with the quilting machine, a lightning bolt icon will appear in the top-left corner of the ProStitcher screen. Pressing that button will perform the same function as the Reconnect Machine button.
www.HandiQuilter.com
Settings Menu | 8.9
Speed Profile
The Speed Profile enables you to customize the relationship between quilting speed and the precision
needed to quilt intricate designs.
To set your speed profile
•
•
•
Select Default for most quilting designs. Only if you feel that the quilting design requires more
precision should you ever need to change the setting.
Select Precision to stitch intricate designs more slowly.
Select Speed for more speed than Precision, but to ensure curves are stitched smoothly.
We recommend that you use the advanced speed profile options only as advised by a technician.
Logging Options
The logging options are for troubleshooting Pro-Stitcher by a technician.
•
Select Settings, Advanced, Logging
Motor Option
The Motor Torque Limit enables you to customize the sensitivity of the Pro-Stitcher motors. For example,
if while quilting the Infinity hits the poles, there is a thread lock, or you’ve selected a quilting speed that
is too fast for the complex design you’re using, the error message Motor Error: Excessive Motor Strain
Detected appears and the motors stop. This setting varies the threshhold for stopping the motors. The
default limit is 50. Most will not need to adjust this value.
When to adjust the Motor Torque Limit
Generally you will make this adjustment when recommended by a technician or if you repeatedly receive
the motor error message that excessive motor strain was detected.
8.10 | Settings Menu
www.HandiQuilter.com
If you receive the motor strain error message during normal stitching conditions
1. Check for and remove any obstructions.
2. Clear the error message by touching the X in the upper-right corner of the message.
3. Press Reconnect Motors or the Motor Error button in the top-right corner of the screen to
reestablish communications between the Pro-Stitcher computer and the motors
4. Reduce your quilting speed and resume quilting.
5. If you continue to receive the error message, change the speed profile (Settings, Advanced,
Speed Profile). If the current setting is Default, select Speed. If the current setting is Speed, select
Default. If the error message persists after you resume quilting, select Precision.
6. If you continue to receive the motor strain error message, adjust the Motor Torque Limit.
To adjust the Motor Torque Limit
1. Select Settings, Advanced, Motor.
2. Increase the Motor Torque Limit to lessen the motor sensitivity or decrease the Motor Torque Limit
to increase the motor sensitivity. Select the number box and enter the value. Typically entering 55
or 60 is sufficient to eliminate the error message except when there is a significant obstruction.
UU CAUTION: Increasing the Motor Torque Limit means that the Pro-Stitcher motors will be less
responsive to obstructions and may continue running, potentially causing damage to the quilt.
Decreasing the Motor Torque Limit means that the Pro-Stitcher motors will stop more easily when
there is resistance.
ÂÂ IMPORTANT: Do not increase the Motor Torque Limit above 100 or decrease it below 40.
About
This option shows version information for the Pro-Stitcher software.
Shut Down
Three shutdown options are available on the Shut Down menu.
To shutdown all software and power down the computer
•
Select Shutdown from the menu. Then select the Shutdown button.
If you select Shutdown, the tablet completely shuts down, including the Infinity console.
To shutdown the software and computer, and then start up again
•
Select Shutdown from the menu. Then select the Reboot button.
If you suspect there may be computer-related issues interfering with Pro-Stitcher, rebooting the computer
often will help.
www.HandiQuilter.com
Settings Menu | 8.11
To exit Pro-Stitcher but keep the computer and Infinity console running
•
Select Shutdown from the menu. Then select the Exit to Windows button.
At times it may be necessary to close down the Pro-Stitcher software and use the standard Windows operating
system.
To restart the Pro-Stitcher software from Windows
•
Locate the Pro-Stitcher shortcut icon on the desktop and double-tap it.
8.12 | Settings Menu
www.HandiQuilter.com
9. Troubleshooting
Problem/Symptom
No display on the touch-screen monitor
LED on the power button at the top
right-hand side of the screen is on.
LED on the power button at the top right-hand
side of the screen is off.
Corrective Measure
The Pro-Stitcher computer is powered off. Press
the Power button at the top-right side of the computer
to turn it on.
There is no power to the tablet computer. Ensure
the power cord to the Pro-Stitcher is plugged into a
powered outlet on one end and the power supply under
the carriage on one of the Y branch ends of the power
cord. Also check that the round barrel connector is
plugged firmly into the mating cable connector under
the Pro-Stitcher carriage.
If all cables are plugged in properly and the LED remains
off, press the Power button on the top-right side of the
monitor.
Touch-screen monitor is not calibrated
Touching the monitor in one place on the
Recalibrate the touch-screen by going to
monitor puts the cursor in a place other than
SETTINGS -> ADVANCED -> CALIBRATE and follow the
where the monitor was touched.
calibration instructions.
The stitch regulator cable is not connected properly
The Pro-Stitcher moves but does not stitch.
Make sure the gray flat stitch regulator cable is plugged
into the back of the C-Pod, the encoder wheel on the
back wheel of the quilting machine, and the encoder
wheel on the carriage.
Check the black cable that connects the Pro-Stitcher
to the machine encoder wheel. This cable has a 3-wire
connector at the end that plugs into the machine’s
stitch regulator encoder circuit board attached to the
back left wheel of the quilting machine.
Verify the Pro-Stitcher and the quilting machine are
communicating with each other by pressing Reconnect
Machine in the Settings -> Advanced menu. If the two
systems are communicating, pressing the Full Stitch or
Half Stitch buttons on the Pro-Stitcher will result in the
quilting machine’s needle performing that function.
Check the gray stitch regulator cable for damage
(the end of the cable that plugs into the C-Pod will have
one wire clipped – this is normal).
www.HandiQuilter.com
Troubleshooting | 9.1
Problem/Symptom
Corrective Measure
The Pro-Stitcher stitches, but the stitch lengths The problem can be narrowed to a specific encoder
vary and the quilting machine slows down or
wheel by running the quilting machine manually
even stops in some directions.
(HQ Sixteen owners will need to press the Switch to
Handlebar Control button at the top left-hand corner
of the screen to pass control back to the handles).
Start the quilting machine from the handlebars in
Stitch Regulated mode and only move the machine left
and right. Then try only moving front and back. If the
quilting machine stops stitching while moving front and
back, then the problem is with the encoder mounted
to the back of the machine. If it stops stitching left
and right then the problem is with the encoder on the
carriage. Make sure the encoder wheels roll on the
tracks when moving the quilting machine and also that
the gray stitch regulator cable is plugged in securely to
the encoders.
An older version of the “Y” encoder is mounted to the HQ Sixteen
The HQ Pro-Stitcher begins to stitch but stops
Make sure the “Y” or “machine” encoder, which is
right away.
mounted to the back left-hand side (when looking from
the front) is the newest version encoder for the HQ
Sixteen. The old version has a 2-inch section of black
plastic heat shrink encasing a small circuit board where
the cable plugs in. The new version does not have that
2-inch section of black heat shrink. If the old encoder
is mounted to the machine, then replace it with the
new encoder that is included in the HQ Pro-Stitcher
accessory bag.
The white gears do not engage the blue flexirack
When the quilting machine is pushed by hand, Make sure the white gears fully engage the blue rack.
the horizontal and/or vertical crosshair lines do Use the manual engagement/disengagement tool to
not move.
adjust. Insert into the hole at the front of the
EZ Carriage.
The X and/or Y axis gears are only partially engaged
Stitched designs appear jagged or wobbly. The If there is motion in the X-axis (left-right), check
system may be skipping teeth when running,
the X-axis gear assembly and make sure nothing is
resulting in a shifting of the design on the quilt. preventing the assembly from springing downward
and putting pressure on the blue rack. If the motion
With the Pro-Stitcher powered and motors
is in the Y-axis (front/back), make sure the blue rack
engaged and enabled (locked in position),
and the white gear are properly aligned and adjust if
pressing the machine side to side or front to
necessary by loosening the two Y-axis bracket mounting
back allows a little motion but the white gear
screws and shifting the Y-axis bracket left/right and redoes not rotate.
tightening the screws. If the white gear is not pressing
upward enough on the blue rack to fully engage the
gears, it may be necessary to install shim washers
betwen the quilting machine base-plates and the Y-axis
bracket to drop the bracket a little.
9.2 | Troubleshooting
www.HandiQuilter.com
Problem/Symptom
Corrective Measure
The Pro-Stitcher stitches, but the stitch lengths The problem can be narrowed to a specific encoder
vary and the quilting machine slows down or
wheel by running the quilting machine manually
even stops in some directions.
(HQ Sixteen owners will need to press the Switch to
Handlebar Control button at the top left-hand corner
of the screen to pass control back to the handles).
Start the quilting machine from the handlebars in
Stitch Regulated mode and only move the machine left
and right. Then try only moving front and back. If the
quilting machine stops stitching while moving front and
back, then the problem is with the encoder mounted
to the back of the machine. If it stops stitching left
and right then the problem is with the encoder on the
carriage. Make sure the encoder wheels roll on the
tracks when moving the quilting machine and also that
the gray stitch regulator cable is plugged in securely to
the encoders.
An older version of the “Y” encoder is mounted to the HQ Sixteen
The HQ Pro-Stitcher begins to stitch but stops
Make sure the “Y” or “machine” encoder, which is
right away.
mounted to the back left-hand side (when looking from
the front) is the newest version encoder for the HQ
Sixteen. The old version has a 2-inch section of black
plastic heat shrink encasing a small circuit board where
the cable plugs in. The new version does not have that
2-inch section of black heat shrink. If the old encoder
is mounted to the machine, then replace it with the
new encoder that is included in the HQ Pro-Stitcher
accessory bag.
The white gears do not engage the blue flexirack
When the quilting machine is pushed by hand, Make sure the white gears fully engage the blue rack.
the horizontal and/or vertical crosshair lines do Use the manual engagement/disengagement tool to
not move.
adjust. Insert into the hole at the front of the
EZ Carriage.
The X and/or Y axis gears are only partially engaged
Stitched designs appear jagged or wobbly. The If there is motion in the X-axis (left-right), check
system may be skipping teeth when running,
the X-axis gear assembly and make sure nothing is
resulting in a shifting of the design on the quilt. preventing the assembly from springing downward
and putting pressure on the blue rack. If the motion
With the Pro-Stitcher powered and motors
is in the Y-axis (front/back), make sure the blue rack
engaged and enabled (locked in position),
and the white gear are properly aligned and adjust if
pressing the machine side to side or front to
necessary by loosening the two Y-axis bracket mounting
back allows a little motion but the white gear
screws and shifting the Y-axis bracket left/right and redoes not rotate.
tightening the screws. If the white gear is not pressing
upward enough on the blue rack to fully engage the
gears, it may be necessary to install shim washers
betwen the quilting machine base-plates and the Y-axis
bracket to drop the bracket a little.
www.HandiQuilter.com
Troubleshooting | 9.3
Problem/Symptom
Corrective Measure
One or more of the pulleys/gears on the X or Y axis assemblies are loose
Stitched designs appear jagged or wobbly.
Monitor the motor assembly while engaged and
enabled to determine which gear/pulley is slipping. It
With the Pro-Stitcher powered and motors
will most likely be either the gear mounted directly to
engaged and enabled (locked in position),
the motor shaft or the gear mounted to the shaft that
pressing the machine side to side or front to
drives the white gear. Use the appropriate Allen wrench
back allows a little motion and the white gear to tighten both set screws on the gear. The motor gear
does rotate.
requires a 1/16” Allen wrench and the larger gear on
the drive axle with the white gear requires a 5/64”
Allen wrench.
The X and Y tension springs are too loose.
The X and Y tension springs may need to be tightened.
Gear tooth skipping occurs, causing the
stitched design to be shifted in either the X or First make sure the Pro-Stitcher version is 14.01.0043
or newer. Using a 3mm Allen wrench, tighten the bolts
the Y direction.
(clockwise) running through the center of the two
springs in the Pro-Stitcher carriage (one on the X motor assembly and one on the Y motor assembly). Only
one or two full rotations is all that is usually required.
Tightening more than three turns will likely damage the
system. Be careful while tightening not to flex the shaft
that the bolt is tightening into or it may break. The quilting machine will need to be removed from the carriage
and the carriage turned upside down to access the X
tension spring. Test that the springs are not too tight by
going to the Freehand screen and pressing the “Engage”
or “Free Motion” buttons to rotate the engagement motor a few times. If they are too tight, the motor will slip
and not complete its rotation. Loosen the tension spring
bolt if this occurs.
Lubrication required between white gears and blue rack
When the Pro-Stitcher carriage levers are
Lubricate the teeth of the white plastic gears for both
engaged squeaking can be heard as the
the X and the Y axes by applying a small amount of
machine is pushed or driven.
silicone lubricant to the teeth of the white gears. Do not
use a solvent-based or an oil-based lubricant (such as
WD-40 or sewing machine oil) as this will attract dust
and eventually clog the gears.
Positioning a pattern using the Reset Home button
When the Reset Home button is pressed, the
The Reset Home button is not intended to be used as
pattern is not positioned properly.
a re-positioning tool. Reset Home simply makes the
current needle position match up with the “X=0, Y=0”
point of the pattern. This “0,0” position can vary from
pattern to pattern, so the best way to reposition is by
using the Area or Reposition tools from the menu.
9.4 | Troubleshooting
www.HandiQuilter.com
Problem/Symptom
Corrective Measure
Quilting machine stuck in a faster speed than selected by Pro-Stitcher
Stitch length is much smaller than selected,
Something has caused the quilting machine to lock up
machine running faster than it should.
at a higher speed (tighter SPI) than selected. Rebooting
both the quilting machine and the Pro-Stitcher
computer should resolve the issue.
No patterns or folders show up in the design library
The current path is pointing to the wrong
Designs are stored on the computer’s hard drive and on
drive letter.
the removable USB flash drive. If you are attempting to
access designs specifically on the USB flash drive, make
sure the USB flash drive is plugged in securely to the
Pro-Stitcher computer. Press Cancel if the Open screen
is already open, remove the USB flash drive, wait about
15 seconds, and then press the Open button again.
The patterns that come pre-loaded on the Handi Quilter
USB Flash drive are located in a folder called Designs on
the USB flash drive (usually drive D:\ or E:\). From the
Open window, select a drive letter by pressing on the
arrow button next to the drive you wish to browse. If
there is a circle with a ^ symbol on the right-hand side
of the button, it means there are more folders in that
particular path.
If there continues to be nothing showing up on the USB
flash drive, plug it into a desktop or laptop computer
and verify that the USB flash drive has the desired files
on it. If the computer says it wants to reformat the flash
drive then the flash drive has gone bad and will need
to be replaced. If it opens but there are no files on the
flash drive, contact Handi Quilter for replacement files.*
*Handi Quilter highly recommends backing up all pattern
files on a home computer or another disk.
Jumps between repeated patterns
Use of any of the Repeat options results in a
jump between each pattern
www.HandiQuilter.com
When using the Repeat functions, if the start and/or
stop points are within the block of the pattern (i.e. they
are not located at the left and right-hand sides of the
pattern block) and/or not at the same height, there will
be a jump between each repeat of the pattern. This can
be corrected by selecting the Point 2 Point box in the
Repeat screen.
Troubleshooting | 9.5
Problem/Symptom
Corrective Measure
Error messages
Motor Error with lightning bolt icon in the top- This will occur with various types of motor errors.
right corner (may occur with various types of
Generally they mean that the Pro-Stitcher cannot
Motor Error messages on the screen).
communicate with the motors. Check that the carriage
is plugged in and that the serial cables are connected
properly into the box behind the Pro-Stitcher computer.
If everything is connected properly and power is
on, press the lightning bolt button to attempt to
reestablish communication with the motors. The icon
will turn to either a red or green motor button once
communications are re-established.
If this occurs during stitching (possibly due to a large
electrostatic discharge (ESD) event or power surge), the
Pro-Stitcher will stop moving and wait for the lightning
bolt icon to be pressed. If the quilting machine is still
stitching at this point, press the STOP button on the
handles. Pro-Stitcher does not resume on its own after
such a disruption for safety reasons and will require
user intervention to resume stitching the design.
When communications are reestablished by pressing
the lightning bolt button, it will be necessary to re-set
the starting point to the position where the stitching
stopped and resume stitching from that point. If the
tablet touch-screen does not respond after such an
ESD or surge event, it may be necessary to re-boot the
tablet using the power button. A mouse may be plugged
into an available USB port and used to save any work
prior to re-booting the tablet.
Buffer Underflow
9.6 | Troubleshooting
If a message with the words Buffer Underflow appears
while stitching, it is an indication that data is not getting
to the motors quickly enough. This may be due to
something in the computer tying up the CPU. Although
it may be possible to resume quilting by simply pressing
red X box to close the error message and then pressing
the Motor Error lightning bolt button at the top righthand corner of the screen, it is best to cancel the
current design stitch-out, save the pattern, and re-boot
the computer. Use the New Start Point function
if necessary to resume from where stitching was
left off.
www.HandiQuilter.com
Problem/Symptom
System Restore or System Repair message
on boot-up.
www.HandiQuilter.com
Corrective Measure
If a message appears on boot-up (black screen, white
text) that asks whether to run System Restore or Start
Windows Normally, select Start Windows Normally by
using the volume buttons on the tablet to move your
selection up or down and use the “Windows” button
to select “Start Normally.” The system should resume
as normal. The computer will default to the System
Restore screen (more of a typical Windows blue/white
screen) if you do not select the Start Normally option in
time. If this occurs, use the power switch to reboot the
computer and try again.
Troubleshooting | 9.7
10. Warranty
Warranty issued should, whenever possible, first
be submitted to the Authorized Representative
who completed your service and training. These
representatives have been selected for their
dedication to customer satisfaction and have been
trained in technical service. They also may provide
follow-up advice, training, service, accessories, and
other services.
HQ Authorized Representatives may offer their
own warranties in addition to those offered
by the manufacturer, but do not obligate the
manufacturer.
HQ Pro-Stitcher® - Limited Warranty
Handi Quilter, Inc. (hereinafter HQ) offers a limited
warranty on the HQ Pro-Stitcher (hereinafter
“Product”) to be free of defects in workmanship
and materials under normal use upon the terms
and conditions hereinafter set forth:
(a) 90 day Limited Warranty: During the first 90
days from date of purchase, HQ will repair any
manufacturing defect without charge for parts or
labor. All subsequent warranties include parts
costs only.
(b) Three year Mechanical Warranty: For any mechanical
failure within this period. Manufacturer will provide
free replacement parts, customer pays for labor
and shipping.
(b), (c) and (d) above shall be limited solely to the
replacement of parts which, in the opinion of HQ
are defective in workmanship or material and are
returned to HQ, or an authorized repair facility, or
such other point or place that may be designated
by HQ. All other costs, including cost of freight and
shipment for repair under this warranty, shall be the
customer’s costs.
The product registration card must be completed
and received by HQ before warranty is valid.
Warranty Exclusions
HQ shall have no obligation for any claim under
this warranty if the HQ Pro-Stitcher has been
misused, abused, neglected, damaged in transit or
has been altered from the standard specifications
established by HQ, if proper cleaning and
maintenance has not been performed, or if the
HQ Pro-Stitcher is used on other frame systems
or with other machines than those specified
by Handi Quilter. No warranties extend beyond
the express warranty offered. HQ disclaims all
other warranties, express or implied, regarding
the Product, including any implied warranties of
merchantability or fitness for a particular purpose.
In the United States, some laws do not allow the
exclusion of the implied warranties.
(c) Lifetime Software Update Warranty: From the date
of purchase HQ will provide updates (minor changes
to the HQ Pro-Stitcher software), free of charge, to
the consumer via electronic downloads. These are
intended to provide the consumer with the latest
software updates for the HQ Pro-Stitcher and are not
the same as Upgrades, which will incur a fee to the
consumer.
(d) Two year Electronic/Electrical Warranty: The electric/
electronic components are warranted to be free from
manufacturing defects for two years from the date of
purchase. If any defect is reported within this period,
manufacturer will provide free replacement parts,
customer pays for labor and shipping. The two year
electronic/electrical warranty will be invalid if the
product is left plugged into a power source when
not in use. This limited warranty stated in sections
www.HandiQuilter.com
Warranty/Training Checklist | 10.1
Specific exclusions of warranty
limitations include, but are not
limited to the following
• G
eneral, consequential, incidental or special
damages including damage to fabric or
material, the cost of rework or lost profits, the
cost of installation or removal of any Products,
and any inspection, testing or redesign caused
by any defect or by the repair or replacement
of Products arising from a defect in any
Product.
• Products which are received by HQ improperly
packaged, altered, or physically damaged.
• Counterfeit or altered label(s) or stickers.
• Broken pins or connectors
• Stripped screws or nuts
• Connector(s) damaged, cracked, missing or
broken.
• Missing, torn or punctured seals(s)
• Any use besides computerized machine quilting
applications
• Operator error in the customary use of the
Product.
• Internal adjustments, tampering or parts
replacement done by anyone except authorized
Representatives or customers specifically
authorized by Handi Quilter Customer Support
or warranty repair personnel on a case by case
basis.
HQ does not assume, or authorize any person
to assume on its behalf, any other obligation of
liability other than that sent forth herein.
Some states do not allow exclusion of limitation
of incidental or consequential damages, so
above limitation or exclusion may not apply. This
warranty gives the purchaser specific legal rights
and the purchaser may also have other rights,
which may vary from State to State.
Exclusive Remedy
Remedy is limited to the repair or replacement
of the defective Product. HQ may elect which
remedy or combination of remedies to provide
at its sole discretion and shall have a reasonable
time, after determining that a defective Product
exists, to repair or replace the defective product.
Replacement Product may be from new or
serviceable used parts. HQ’s warranty applies to
repairs or replaced Products for the balance of the
applicable period of the original warranty or ninety
days from the date of shipment of a repaired or
replaced Product, whichever is longer.
HQ’s entire liability for any defective Product shall
in no event exceed the purchase price for the
defective Product. This limitation applies even if
Handi Quilter cannot or does not repair or replace
any defective Product.
The warranty does not cover and the user assumes
the risk of and there is hereby excluded any liability
to HQ for failure, defects, loss, deterioration,
personal injury or damage which are due to: (1)
ordinary wear and tear or exposure, (2) abuse,
misuse, negligence, operator error, or (3) use of
parts, components, or accessories not authorized
by HQ.
In no event shall HQ be liable to the purchaser
of the Product or to third parties for special or
consequential damages, including, but not limited
to, death or personal injuries.
10.2 | Warranty/Training Checklist
HQ Pro-Stitcher User Manual
Warranty Claims
Service under the above warranties may be
obtained by returning the product, with proof
of purchase, to the authorized Representative
from whom the product was purchased, a local
Representative, or to Handi Quilter Support.
Any product to be returned to the factory,
either by customers or Representatives, must be
accompanied by a Return Material Authorization
Number (RMA). RMAs may be obtained by email
([email protected]) or by calling customer
support at 801-292-7988 or toll-free at 1-877697-8458. If it is determined that the Product may
be defective, an RMA number will be issued with
instructions for Product return. An unauthorized
return (a return without an RMA number) will be
shipped back to customer at customer’s expense.
Authorized returns are to be shipped prepaid and
insured in an approved shipping container. The
original box and packaging materials should be kept
for storing or shipping.
positioning, bearing retainers, hook axial play and
timing, presser and needle bar adjustment, and
internal lubrication to take-up lever, hopping foot
levers, bushings/bearings.
Handi Quilter, Inc.
Customer Relations
501 N. 400 W.
North Salt Lake, UT 84054
Toll Free: 1-877-MY-QUILT (697-8458)
Local Phone: 801-292-7988
[email protected]
Shipping Cost
Shipping is the responsibility of the customer.
Product Service and Maintenance
Periodically use a small brush to clean all lint and
threads from under the carriage, track and rack.
Keep rack and track clean and clear of any foreign
material, build up, or obstruction.
Follow HQ Quilting Machine Service and
Maintenance for best results with the
HQ Pro-Stitcher.
Replace needles every 2-4 hours (1-2 per large
quilt) and lubricate hook every 3-4 hours of use
(about every 2nd bobbin change). Periodically
check the thread tensioner. Use small brush to
clean out all lint, loose thread or obstructions from
the bobbin hook each time you begin to use the
HQ Pro-Stitcher and HQ quilting machine.
Servicing is recommended for your HQ quilting
machine annually from a qualified representative.
Servicing will cover belt tensioning, encoder
www.HandiQuilter.com
Warranty/Training Checklist | 10.3
This page intentionally left blank.
10.4 | Warranty/Training Checklist
HQ Pro-Stitcher User Manual
HQ Pro-Stitcher® Warranty Registration
Mail or Fax completed Warranty Registration Card within 30 days of purchase. If you have questions,
email [email protected] or call Customer Relations at 1-877-697-8458. Online warranty
registration is also available at HandiQuilter.com.
MAIL: Handi Quilter, Inc.
FAX: 801-294-3011
Warranty Registration Dept.
501 N 400 W
North Salt Lake, Utah 84054
Cut along dotted line and mail or fax this registration information within 30 days of purchase.
HQ Pro-Stitcher Warranty Registration Card
The HQ Pro-Stitcher warranty consists of two-year electronic/electrical, three-year mechanical and
lifetime software updates (see detailed warranty information in HQ Pro-Stitcher User Manual). Check
with your local HQ Representative for details on service or making warranty claims.
Customer Name:
Company/Business Name (if applicable):
Address:
City, State, Zip:
Daytime Phone:
Evening Phone:
Fax:
Email:
HQ Pro-Stitcher Serial Number:
Order Number (5 digits):
Purchase Date:
Date Product Received:
Location of Purchase (Shop or Show name, City & State):
Signature:
Date:
www.HandiQuilter.com
Warranty/Training Checklist | 10.5
This page intentionally left blank.
10.6 | Warranty/Training Checklist
HQ Pro-Stitcher User Manual
HQ Pro-Stitcher Training Checklist
Customer Name
Date of Purchase
HQ Representative Shop Name
Date of Training
Installation and Set Up
•
Rotation (Mirror, Flip,
2-Point, Group)
Crop (Inside, Outside,
Open, Closed)
Repeat
Resize
Skew and Align
Freehand Record and Mark
Reposition (by Corner,
Center, Start, End, Drag &
Drop, Nudge)
☐
☐ •
☐
☐ •
☐ •
•
HQ Pro-Stitcher Overview
•
• Disable/Enable Motors
☐ •
• Pull-up Bobbin Thread
☐
• Zoom/Pan Function
☐
• Refresh
☐
• Half-Stitch
☐ Art & Stitch (if applicable)
• Reset Home
☐ • Creating a Design
• Follow
☐ • Saving a Design
• Loading a Design from
Design Menu
outside source
• Find drive where design
• Passing a Design back and
are located
☐
forth from Pro-Stitcher
• Show File with all Designs ☐
• Load Design
☐ Quilt Menu
• Design
☐ • New Start/End Points
• Box
☐ • Jump Points
• Jump Points
☐ • Move (Continuous & Stitch)
• Start/Stop
☐ • Channel Lock
• Undo
☐ • Trace Outline
• Redo
☐ • Box
• History
☐ • Area
• Baseline
☐ • Pause
• Loading and Saving a Design☐ • Emergency Stop
• Setting an Area
☐
•
•
•
•
•
Rack System
Carriage System
Encoder Cables
Gears Engage in Racks
Quick Release Mechanism
The items listed above have been explained to
me by my HQ Rep.
Signature of Owner
Settings Menu
☐ •
•
☐ •
☐ •
☐ •
☐ •
☐ •
•
•
☐ •
Speed
☐
Auto Jump
☐
Stitches-Per-Inch
☐
Tie Off (Tack and Micro)
☐
Pullup
☐
Pause Delay
☐
Switch to Handlebar Control☐
Reconnect Motors
☐
Reconnect Machine
☐
Shut Down (Shutdown,
Reboot, Exit to Windows) ☐
☐ Cleaning and Maintenance
☐ • Cleaning Rack
☐
• Maintenance of HQ
☐
Machine ☐
☐
Warranty Review
•
☐ •
☐
☐
☐
☐
☐
☐
☐
☐
Review Manufacturer’s
Warranty
Sign Checklist ☐
☐
I have covered the items listed above with my
customer.
Signature of Trainer
Note to the HQ Rep: Upon completion, please cut along dotted line and fax the signed copy to
Handi Quilter at 801-294-3011. It is okay to photocopy this page.
www.HandiQuilter.com
Warranty/Training Checklist | 10.7
10.8 | Warranty/Training Checklist
HQ Pro-Stitcher User Manual
11. Handi Quilter Printouts
A place for the latest information
For news about Pro-Stitcher udpates, watch: www.handiquilter.com/prostitcher-download
For tips and tutorials, watch: www.handiquilter.com/education/pro-stitcher/
See something you want to remember? Print it out and keep it here.
www.HandiQuilter.com/ProStitcher
HQ Printouts 11.1
11.2 HQ Printouts
HQ Pro-Stitcher for Infinity User Manual
12. Tutorials
Tutorials from the Handi Quilter educators
Go to www.handiquilter.com/education/pro-stitcher for lessons, tips and tutorials for using the latest
software updates.
Print them out and keep them handy in this section of your user manual. We write the tutorials with
step-by-step instructions, so you feel as though one of the Handi Quilter educators is standing right by
your side as you learn.
www.HandiQuilter.com
09/01/13
Tutorials 12.1
12.2 Tutorials
www.HandiQuilter.com
13. Designs
A place to store your design catalogs
Even though HQ Pro-Stitcher offers an easy-to-use way to view your quilting designs, it’s sometimes nice to
have them printed on paper for browsing. If you quilt for hire, it’s a good way to let your customers choose
a design.
We suggest you three-hole punch your catalogs and keep them here with your HQ Pro-Stitcher for Infinity
user manual.
HQ Pro-Stitcher and Art & Stitch designs
Use your Art & Stitch program to organize and print catalogs of all of the designs in HQ Pro-Stitcher and
Art & Stitch.
Print Catalog is a powerful function to show and to print all designs of all formats on paper. This function
will print thumbnails and file names of all designs in a folder. You will find Print Catalog in the Art & Stitch
software program and you can use it to create catalogs of all of your designs, regardless of their origin.
www.HandiQuilter.com
Designs 13.1
13.2 Designs
HQ Pro-Stitcher for Infinity User Manual
14. My Ideas
You know you’ll forget if you don’t save it here
This is a section to keep pictures, tearsheets from magazines, printouts from the web. Anything you find
inspirational should find its way here!
www.HandiQuilter.com
My Ideas 14.1
Handi Quilter, Inc.
501 N 400 W
North Salt Lake, UT 84054
1-877-MY-QUILT (697-8458) • www.HandiQuilter.com
HQ Pro-Stitcher® is part of the family of innovative quilting products from Handi Quilter®
PRINTED 05 /01 /2015
© 2015 Handi Quilter, Inc. All rights reserved. Printed in the U.S.A.