1
Download 2 - Graco Inc.
Transcript
Skin Injection Hazard Use with high pressure equipment, generally equipment with pressure rating of 900 psi or higher. There sions of this section. 1) manual guns, 2) UL-1450 compliant equipment 3) automatic guns,/dispense val tion valves, 4) heated hoses. Since the text contains mostly “Do not” statements, the symbols have lines them. Warnings WARNING WARNING SKIN HAZARD SKININJECTION INJECTION HAZARD - Basic High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may l like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatm treatment. point gun at anyone at of any •• DoDo notnot point gun at anyone or at anyorpart thepart body.of the body. •• DoDo notnot put put youryour hand hand over the dispense outlet. tip. over the spray •• DoDo notnot stopstop or deflect leaks with yourwith hand, body, glove,body, or rag.glove, or rag. or deflect leaks your hand, •• Engage trigger lock when not Do not spray without tipspraying. guard and trigger guard installed. •• Follow Pressure Relief Procedure in spraying. this manual, when you stop spraying and before cleaning, Engage trigger lock when not checking, or servicing equipment. • Follow Pressure Relief Procedure in this manual, when you stop spraying and before c checking, or servicing equipment. MOVING PARTS HAZARD SKIN Use with UL1450 Compliance Moving INJECTION parts can pinchHAZARD or amputate- fingers and other body parts. •DoKeep clearthe of moving not aim gun at,parts. or spray any person or animal. •• DoKeep not operate equipment with protective covers hands and other body partsguards awayor from theremoved. discharge. For example, do not try to sto • Pressurized equipment can start without warning. Before checking, moving, or servicing any part of the body. equipment, follow the Pressure Relief Procedure in this manual. Disconnect power or air • supply. Always use the nozzle tip guard. Do not spray without nozzle tip guard in place. • Use Graco nozzle tips. •EQUIPMENT Use caution when cleaning and changing nozzle tips. in the case where the nozzle tip clo MISUSE HAZARD spraying, follow the Pressure Misuse can cause death or serious injury. Relief Procedure for turning off the unit and relieving the • Dobefore not operate the unitthe when fatigued the influence of drugs or alcohol. removing nozzle tiportounder clean. Fire and Explosion Hazard •• DoDo notnot exceed thethe maximum working pressure or temperature the lowest rated system leave unit energized or under pressure rating whileofunattended. When the unit is not component. See Technical Data in all equipment manuals. off the unit and follow the Pressure Relief Procedure for turning off the unit. • Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data • in High-pressure sprayRead is able inject toxins into the body andFor cause serious bodily injury. all equipment manuals. fluidto and solvent manufacturer’s warnings. complete Pressurized Aluminum Parts Hazard that injection occurs, get request immediate information about your material, MSDS surgical forms from treatment. distributor or retailer. • Check hoses and parts for signs of damage. Replace any damaged hoses or parts. • Check equipment daily. Repair or replace worn or damaged parts immediately with genuine replacement parts only.parts only. Use with equipment pressurized aluminum Equipment havereplacement aluminum parts thatoraren’t pres • manufacturer’s Thiswith system is capable of producing XXXX psi. Usemay Graco parts accesso Dorated not alter or modify equipment. ized - check• with engineering. a minimum of XXXX psi. • Use equipment only for its intended purpose. Call your distributor for information. • Always engage the trigger lock when not spraying. Verify the trigger lock is functioning pr • Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces. that all connections operating the unit. •• DoVerify not kink or over bend hoses or are use secure hoses to before pull equipment. • Know how to stop the unit and bleed pressure quickly. Be thoroughly familiar with the con • Keep children and animals away from work area. • WARNING Comply with all applicable safety regulations. PRESSURIZED ALUMINUM PARTS HAZARD PRESSURIZED ALUMINUM PARTS HAZARD Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or Do notcontaining use 1,1,1-trichloroethane, methylenealuminum chloride,equipment. other halogenated solvents or fluid fluids such solvents in pressurized Such use hydrocarbon can cause serious chemical reaction and equipment rupture, and result in death, seriousSuch injury,use andcan property damage. containing such solvents in pressurized aluminum equipment. cause serious chemical reaction and equipment rupture, and result in death, serious injury, and property damage. 4 Plastic Parts Cleaning Solvent Hazard GC-1306S Created for CEDs Texture Sprayer. May have use with other waterbase application equipment with plastic parts th can be damaged by certain solvents.
