Download 6bnz user`s manual

6BNZ
USER'S MANUAL
1.
System power on by PS/2 Mouse: First, enable this function
in CMOS Setup, then you can power on the system by
double clicking the right or left button of your PS/2 Mouse.
2.
System power on by Keyboard: If your ATX power supply
supports 300 mA 5V Stand-By current (dependent on the
specification of keyboards), you can power on your system
by entering password from the Keyboard after setting the
“Keyboard power on” jumper (JP4) and password in CMOS
Setup.
3.
Modem Ring-On. (COM A , B)
4.
Support 3 steps ACPI LED.
5.
ATi 3D RAGE PRO graphics acceleration Onboard.
6.
YAMAHA YMF715E Audio chip Onboard (Optional).
7.
INTEL SB82558B LAN chip Onboard (Optional).
8.
Wake-Up on LAN. (The ATX power supply supports larger
than 720 mA 5V Stand-By current) (Optional).
For Intel Pentium II / III / Celeron Processor MAINBOARD
R-21-01-090526
Quick Installation Guide
REV. 2.1 First Edition
The author assumes no responsibility for any errors or omissions which may
appear in this document nor does it make a commitment to update the
information contained herein.
Third-party brands and names are the property of their respective
owners.
Sound Blaster is a registered trademark of Creative Technology Ltd in the
United States and certain other countries. Sound Blaster-LINK and SB-LINK
are trademarks of Creative Technology Ltd.
2
Quick Installation Guide
May. 26, 1999 Taipei, Taiwan
I. Quick Installation Guide :
CPU SPEED SETUP
The default system bus speed is 66 / 100MHz. The user can select the
system bus speed (JP1) and change the DIP SWITCH (SW) selection to set
up the CPU speed for 233- 633MHz processor.
M The CPU speed must match with the frequency RATIO. It will cause
system hanging up if the frequency RATIO is higher than CPU's.
CLK RATIO
X3
X3.5
X4
X4.5
X5
X5.5
X6
X6.5
X7
X 7.5
X8
X 8.5
X9
X 9.5
1
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
2
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
3
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
4
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
JP1
1-2 CLOSE :
System Speed is set to 66 MHz
2-3 CLOSE :
Set system speed to Auto − auto detect system
speed (66 / 100MHz FSB)
OPEN :
System Speed is set to 100MHz
MThere are two ways to set system speed
2
6BNZ
1. 66MHz (JP1) (1-2 short) or Auto detect (2-3 short)
2. 100MHz (JP1) (1-2-3 open) or Auto detect (2-3 short)
+ The black part in the picture is the white extruding piece of the
DIP switch.
1. Pentium II / Celeron 233 MHz / 66MHz FSB
Intel
SB82558B
3D RAGE
PRO
6BNZ
PIIX4
82443BX
JP1
OFF ON
1
2
3
1
2
3
1
2
3
4
JP1
SW
2. Pentium II / Celeron 266MHz / 66MHz FSB
OFF ON
JP1
1
2
3
1
2
3
1
2
3
4
JP1
SW
3
Quick Installation Guide
3. Pentium II/Celeron 300MHz /Celeron 300A MHz /66MHz FSB
OFF ON
JP1
1
2
3
1
2
3
1
2
3
4
JP1
SW
4. Pentium II / Celeron 333MHz / 66MHz FSB
OFF ON
JP1
1
2
3
1
2
3
1
2
3
4
JP1
SW
5. Pentium II / Celeron 366 MHz / 66MHz FSB
OFF ON
JP1
1
2
3
1
2
3
1
2
3
4
JP1
SW
6. Pentium II / Celeron 400 MHz / 66MHz FSB
OFF ON
JP1
1
2
3
1
2
3
1
2
3
4
JP1
SW
4
6BNZ
7. Pentium II / Celeron 433 MHz / 66MHz FSB
OFF ON
JP1
1
2
3
1
2
3
1
2
3
4
JP1
SW
8. Pentium II 350MHz / 100MHz FSB
OFF ON
JP1
1
2
3
1
2
3
1
2
3
4
JP1
SW
9. Pentium II 400MHz / 100MHz FSB
OFF ON
JP1
1
2
3
1
2
3
1
2
3
4
JP1
SW
10. Pentium III 450MHz / 100MHz FSB
OFF ON
JP1
1
2
3
1
2
3
1
2
3
4
JP1
SW
5
Quick Installation Guide
11. Pentium III 500MHz / 100MHz FSB
OFF ON
JP1
1
2
3
1
2
3
1
2
3
4
JP1
SW
12. Pentium III 550MHz / 100MHz FSB
OFF ON
JP1
1
2
3
1
2
3
1
2
3
4
JP1
SW
13. Pentium III 600MHz / 100MHz FSB
OFF ON
JP1
1
2
3
1
2
3
1
2
3
4
JP1
SW
14. Pentium III 650MHz / 100MHz FSB
OFF ON
JP1
1
2
3
1
2
3
1
2
3
4
JP1
SW
6
6BNZ
II. Jumper setting:
SPK : Speaker Connector
3D RAGE
PRO
Intel
SB82558B
6BNZ
PIIX4
82443BX
1
Pin No
Function
4
3
Data
Nc
RST : Rest Switch
7
2
GND
1
Vcc
Quick Installation Guide
HDD
LED
SUS
LED
PWR PWR SUS
LED
SW
SW
RST
SW
R S T S W : Reset SWITCH Connector
Open : Normal Operation
Short : For Hardware Reset System
S U S S W : Suspend Function SWITCH
Open : Normal Operation
Short : For System Entering Green Mode
P W R S W : POWER SWITCH Connector
Open : Normal Operation
Short : For Hardware Power ON/OFF
PWR LED : POWER LED
SUS LED : Suspend LED
H D D LED : HDD Disk Active LED
LAN Connector (Optional)
LAN
MDM
WAKE WAKE
LAN
LED
LAN LED : LAN ACTIVE LED
M D M WAKE : Modem Ring On Connector
LAN WAKE : Wake On LAN Connector
POWER1 : ATX Power Connector
8
6BNZ
1
Pin No
3,5,7,13,
15-17
4,6,19,20
1,2,11
10
12
18
8
9
14
Function
GND
VCC (+5V)
3.3V
+12V
−12V
−5V
Power Good
5V SB (Stand by +5V)
PS-ON (Soft ON/OFF)
POWER2 : ATX Power FAN Connector (Optional)
9
Quick Installation Guide
Pin No
Function
1
FAN Monitor
2
FAN Control
3
3.3V SENSE
4
NC
5
NC
6
NC
1
SYSTEM FAN PWR : System Cooling Fan Power Connector
Pin No.
1
1
Function
GND
2
+12V
3
SENSE
WAKE On LAN Connector (Optional)
10
6BNZ
JP1
1
Pin No.
Function
1
5V SB
2
GND
3
Signal
JP9/CN3 : CD Audio Line-in Connector (Optional)
1
L
G
JP 9
G
R
1
G
L
CN 3
G
R
J7 : CPU FAN PWR (CPU Cooling Fan Power Connector)
11
Quick Installation Guide
3D RAGE
PRO
Intel
SB82558B
6BNZ
PIIX4
J7
Pin No.
1
1
82443BX
Function
GND
2
+12V
3
SENSE
J12 : System FAN PWR (System Cooling Fan Power Connector )
(Optional)
3D RAGE
PRO
Intel
SB82558B
6BNZ
PIIX4
J12
1
82443BX
Pin No.
1
GND
2
+12V
3
SENSE
PS/2 Mouse and IBM PS/2 Keyboard Connector
12
Function
6BNZ
d
PS/2 MOUSE
3D RAGE
PRO
Intel
SB82558B
6BNZ
PIIX4
PS/2 KEYBOARD
PS/2 Mouse
82443BX
Pin No.
Function
1
Data
2
NC
3
GND
4
VCC(+5)
5
Clock
6
NC
VGA : VGA Port
3D RAGE
PRO
Intel
SB82558B
6BNZ
PIIX4
82443BX
13
Quick Installation Guide
LPT : Printer Port
3D RAGE
PRO
Intel
SB82558B
6BNZ
PIIX4
82443BX
COM A : Serial port1
3D RAGE
PRO
Intel
SB82558B
6BNZ
COM A
PIIX4
82443BX
14
6BNZ
COM B : Serial port 2
3D RAGE
PRO
Intel
SB82558B
6BNZ
COM B
PIIX4
82443BX
USB : USB Connector
3D RAGE
PRO
Intel
SB82558B
6BNZ
PIIX4
82443BX
15
Quick Installation Guide
IDE1 : Primary IDE port
RED LINE
1
IDE2 : Secondary IDE port
RED LINE
1
16
6BNZ
FLOPPY : FLOPPY PORT
RED LINE
1
JP4 : Keyboard Power On
JP4
3D RAGE
PRO
Intel
SB82558B
6BNZ
PIIX4
1
1-2 Short :
Enable Keyboard Power On.
1
2-3 Short :
Disable Keyboard Power On.
82443BX
17
Quick Installation Guide
J8 : By PASS ATX PWR CTRL
J8
3D RAGE
PRO
Intel
SB82558B
1
Open: Soft Off
Short: Full on
6BNZ
PIIX4
Pin No.
Function
1
Signal
2
GND
82443BX
JP6 : SB-LINK (Creative PCI Sound Card Support)(Optional)
3D RAGE
PRO
Intel
SB82558B
JP6
6B
6 NZ
PIIX4
4
2
82443BX
18
5
1
Pin No.
1
2
3
4
5
6
Function
Signal
GND
NC
Signal
GND
Signal
6BNZ
J11 : LAN Power On (Optional)
J11
3D RAGE
PRO
1
1-2 Short :
Intel
SB82558B
E n a b l e L A N P o w e r On .
6BNZ
1
2-3 Short :
PIIX4
Disable LAN Power On .
82443BX
JP11 : On-Board LAN Function (Optional)
JP11
3D RAGE
PRO
1
Intel
SB82558B
1-2 Short :
L A N Disabled .
6BNZ
1
2-3 Short :
L A N Enabled .
PIIX4
82443BX
19
Quick Installation Guide
On-Board LAN Connector (Optional)
1
3D RAGE
PRO
2
Intel
SB82558B
1 - Yellow LED
(LAN Active LED)
2 – Green LED
(LAN Link LED)
6BNZ
PIIX4
82443BX
J9 : On-Board Sound Function (Optional)
J9
1
3D RAGE
PRO
Intel
SB82558B
1-2 Short :
Disable On-Board Sound
6BNZ
1
PIIX4
2-3 Short :
Enable On-Board Sound
82443BX
20
6BNZ
Game Port / Audio Port (Optional)
Audio Port
3D RAGE
PRO
Intel
SB82558B
MIC
6BNZ
Line Out
Line In
PIIX4
CN3
Game Port
82443BX
1
CN4 : On-Board Sound CD-Line In (Optional)
CN4
3D RAGE
PRO
Intel
SB82558B
ON-Board Sound Function
6BNZ
PIIX4
82443BX
21
G
R
G
L
Quick Installation Guide
JP10 : On-Board VGA
JP10
3D RAGE
PRO
1
1-2 Short :
Disable On-Board VGA
Intel
SB82558B
6BNZ
PIIX4
1
2-3 Short :
Enable On-Board VGA
82443BX
JP9 : Release On-Board VGA from occupying IRQ Resource
(It is not to enable or disable On-Board VGA Function.)
JP9
3D RAGE
PRO
1
1-2 Short :
Disable VGA Int.
Intel
SB82558B
6BNZ
PIIX4
1
2-3 Short :
Enable VGA Int.
82443BX
22
6BNZ
JP12 : CLEAR CMOS FUNCTION
JP12
1
3D RAGE
PRO
Intel
SB82558B
1-2 Close: Clear CMOS
6BNZ
1
2-3 Close: Normal
PIIX4
82443BX
J14 : Internal Buzzer
3D RAGE
PRO
Intel
SB82558B
6BNZ
J14
PIIX4
Short :
Enable Internal Buzzer
82443BX
Open :
Disable Internal Buzzer
23
Quick Installation Guide
BAT1 : BATTERY
3D RAGE
PRO
Intel
SB82558B
6BNZ
PIIX4
82443BX
BAT+
MDanger of explosion if battery is incorrectly replaced.
MReplace only with the same or equivalent type recommended by the
manufacturer.
MDispose of used batteries according to the manufacturer’ s instructions.
24
6BNZ
III. Top Performance Test Setting:
Users have to modify the value for each item in chipset features as follow
for top performance setting.
**
Each value of items as above depends on your hardware configuration :
CPU , SDRAM , Cards , etc.
Please modify each value of items if your system does not work properly
.
25
Quick Installation Guide
The following performance data list is the testing results of some popular
benchmark testing programs.
These data are just referred by users, and there is no responsibility for
different testing data values gotten by users. (The different Hardware &
Software configuration will result in different benchmark testing results.)
• CPU
Pentium II processor
• DRAM
(128 × 2) MB SDRAM (SEC KM48S8030BT-GH)
• CACHE SIZE
512 KB included in CPU
• DISPLAY
ATi RAGE Pro AGP Display Onboard (4MB SGRAM)
• STORAGE
Onboard IDE (IBM DHEA-36481)
• O.S.
Windows® NT 4.0
• DRIVER
Display Driver at 1024 x 768 x 256 colors x 75Hz.
Triones Bus Master IDE Driver 3.70
Processor
Intel Pentium II
266MHz (66×4) 350MHz (100×3.5)
Winbench98
CPU mark32
FPU Winmark
Business Disk
Hi-End Disk
Business Graphics
Hi-End Graphics
719
1380
1840
4370
156
171
862
1800
1900
4620
195
219
29.4
32.8
34.1
37.4
Winstone98
Business
Hi-End
26