Download 6bnz user`s manual
Transcript
6BNZ USER'S MANUAL 1. System power on by PS/2 Mouse: First, enable this function in CMOS Setup, then you can power on the system by double clicking the right or left button of your PS/2 Mouse. 2. System power on by Keyboard: If your ATX power supply supports 300 mA 5V Stand-By current (dependent on the specification of keyboards), you can power on your system by entering password from the Keyboard after setting the “Keyboard power on” jumper (JP4) and password in CMOS Setup. 3. Modem Ring-On. (COM A , B) 4. Support 3 steps ACPI LED. 5. ATi 3D RAGE PRO graphics acceleration Onboard. 6. YAMAHA YMF715E Audio chip Onboard (Optional). 7. INTEL SB82558B LAN chip Onboard (Optional). 8. Wake-Up on LAN. (The ATX power supply supports larger than 720 mA 5V Stand-By current) (Optional). For Intel Pentium II / III / Celeron Processor MAINBOARD R-21-01-090526 Quick Installation Guide REV. 2.1 First Edition The author assumes no responsibility for any errors or omissions which may appear in this document nor does it make a commitment to update the information contained herein. Third-party brands and names are the property of their respective owners. Sound Blaster is a registered trademark of Creative Technology Ltd in the United States and certain other countries. Sound Blaster-LINK and SB-LINK are trademarks of Creative Technology Ltd. 2 Quick Installation Guide May. 26, 1999 Taipei, Taiwan I. Quick Installation Guide : CPU SPEED SETUP The default system bus speed is 66 / 100MHz. The user can select the system bus speed (JP1) and change the DIP SWITCH (SW) selection to set up the CPU speed for 233- 633MHz processor. M The CPU speed must match with the frequency RATIO. It will cause system hanging up if the frequency RATIO is higher than CPU's. CLK RATIO X3 X3.5 X4 X4.5 X5 X5.5 X6 X6.5 X7 X 7.5 X8 X 8.5 X9 X 9.5 1 ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF 2 OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF 3 ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF 4 ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF JP1 1-2 CLOSE : System Speed is set to 66 MHz 2-3 CLOSE : Set system speed to Auto − auto detect system speed (66 / 100MHz FSB) OPEN : System Speed is set to 100MHz MThere are two ways to set system speed 2 6BNZ 1. 66MHz (JP1) (1-2 short) or Auto detect (2-3 short) 2. 100MHz (JP1) (1-2-3 open) or Auto detect (2-3 short) + The black part in the picture is the white extruding piece of the DIP switch. 1. Pentium II / Celeron 233 MHz / 66MHz FSB Intel SB82558B 3D RAGE PRO 6BNZ PIIX4 82443BX JP1 OFF ON 1 2 3 1 2 3 1 2 3 4 JP1 SW 2. Pentium II / Celeron 266MHz / 66MHz FSB OFF ON JP1 1 2 3 1 2 3 1 2 3 4 JP1 SW 3 Quick Installation Guide 3. Pentium II/Celeron 300MHz /Celeron 300A MHz /66MHz FSB OFF ON JP1 1 2 3 1 2 3 1 2 3 4 JP1 SW 4. Pentium II / Celeron 333MHz / 66MHz FSB OFF ON JP1 1 2 3 1 2 3 1 2 3 4 JP1 SW 5. Pentium II / Celeron 366 MHz / 66MHz FSB OFF ON JP1 1 2 3 1 2 3 1 2 3 4 JP1 SW 6. Pentium II / Celeron 400 MHz / 66MHz FSB OFF ON JP1 1 2 3 1 2 3 1 2 3 4 JP1 SW 4 6BNZ 7. Pentium II / Celeron 433 MHz / 66MHz FSB OFF ON JP1 1 2 3 1 2 3 1 2 3 4 JP1 SW 8. Pentium II 350MHz / 100MHz FSB OFF ON JP1 1 2 3 1 2 3 1 2 3 4 JP1 SW 9. Pentium II 400MHz / 100MHz FSB OFF ON JP1 1 2 3 1 2 3 1 2 3 4 JP1 SW 10. Pentium III 450MHz / 100MHz FSB OFF ON JP1 1 2 3 1 2 3 1 2 3 4 JP1 SW 5 Quick Installation Guide 11. Pentium III 500MHz / 100MHz FSB OFF ON JP1 1 2 3 1 2 3 1 2 3 4 JP1 SW 12. Pentium III 550MHz / 100MHz FSB OFF ON JP1 1 2 3 1 2 3 1 2 3 4 JP1 SW 13. Pentium III 600MHz / 100MHz FSB OFF ON JP1 1 2 3 1 2 3 1 2 3 4 JP1 SW 14. Pentium III 650MHz / 100MHz FSB OFF ON JP1 1 2 3 1 2 3 1 2 3 4 JP1 SW 6 6BNZ II. Jumper setting: SPK : Speaker Connector 3D RAGE PRO Intel SB82558B 6BNZ PIIX4 82443BX 1 Pin No Function 4 3 Data Nc RST : Rest Switch 7 2 GND 1 Vcc Quick Installation Guide HDD LED SUS LED PWR PWR SUS LED SW SW RST SW R S T S W : Reset SWITCH Connector Open : Normal Operation Short : For Hardware Reset System S U S S W : Suspend Function SWITCH Open : Normal Operation Short : For System Entering Green Mode P W R S W : POWER SWITCH Connector Open : Normal Operation Short : For Hardware Power ON/OFF PWR LED : POWER LED SUS LED : Suspend LED H D D LED : HDD Disk Active LED LAN Connector (Optional) LAN MDM WAKE WAKE LAN LED LAN LED : LAN ACTIVE LED M D M WAKE : Modem Ring On Connector LAN WAKE : Wake On LAN Connector POWER1 : ATX Power Connector 8 6BNZ 1 Pin No 3,5,7,13, 15-17 4,6,19,20 1,2,11 10 12 18 8 9 14 Function GND VCC (+5V) 3.3V +12V −12V −5V Power Good 5V SB (Stand by +5V) PS-ON (Soft ON/OFF) POWER2 : ATX Power FAN Connector (Optional) 9 Quick Installation Guide Pin No Function 1 FAN Monitor 2 FAN Control 3 3.3V SENSE 4 NC 5 NC 6 NC 1 SYSTEM FAN PWR : System Cooling Fan Power Connector Pin No. 1 1 Function GND 2 +12V 3 SENSE WAKE On LAN Connector (Optional) 10 6BNZ JP1 1 Pin No. Function 1 5V SB 2 GND 3 Signal JP9/CN3 : CD Audio Line-in Connector (Optional) 1 L G JP 9 G R 1 G L CN 3 G R J7 : CPU FAN PWR (CPU Cooling Fan Power Connector) 11 Quick Installation Guide 3D RAGE PRO Intel SB82558B 6BNZ PIIX4 J7 Pin No. 1 1 82443BX Function GND 2 +12V 3 SENSE J12 : System FAN PWR (System Cooling Fan Power Connector ) (Optional) 3D RAGE PRO Intel SB82558B 6BNZ PIIX4 J12 1 82443BX Pin No. 1 GND 2 +12V 3 SENSE PS/2 Mouse and IBM PS/2 Keyboard Connector 12 Function 6BNZ d PS/2 MOUSE 3D RAGE PRO Intel SB82558B 6BNZ PIIX4 PS/2 KEYBOARD PS/2 Mouse 82443BX Pin No. Function 1 Data 2 NC 3 GND 4 VCC(+5) 5 Clock 6 NC VGA : VGA Port 3D RAGE PRO Intel SB82558B 6BNZ PIIX4 82443BX 13 Quick Installation Guide LPT : Printer Port 3D RAGE PRO Intel SB82558B 6BNZ PIIX4 82443BX COM A : Serial port1 3D RAGE PRO Intel SB82558B 6BNZ COM A PIIX4 82443BX 14 6BNZ COM B : Serial port 2 3D RAGE PRO Intel SB82558B 6BNZ COM B PIIX4 82443BX USB : USB Connector 3D RAGE PRO Intel SB82558B 6BNZ PIIX4 82443BX 15 Quick Installation Guide IDE1 : Primary IDE port RED LINE 1 IDE2 : Secondary IDE port RED LINE 1 16 6BNZ FLOPPY : FLOPPY PORT RED LINE 1 JP4 : Keyboard Power On JP4 3D RAGE PRO Intel SB82558B 6BNZ PIIX4 1 1-2 Short : Enable Keyboard Power On. 1 2-3 Short : Disable Keyboard Power On. 82443BX 17 Quick Installation Guide J8 : By PASS ATX PWR CTRL J8 3D RAGE PRO Intel SB82558B 1 Open: Soft Off Short: Full on 6BNZ PIIX4 Pin No. Function 1 Signal 2 GND 82443BX JP6 : SB-LINK (Creative PCI Sound Card Support)(Optional) 3D RAGE PRO Intel SB82558B JP6 6B 6 NZ PIIX4 4 2 82443BX 18 5 1 Pin No. 1 2 3 4 5 6 Function Signal GND NC Signal GND Signal 6BNZ J11 : LAN Power On (Optional) J11 3D RAGE PRO 1 1-2 Short : Intel SB82558B E n a b l e L A N P o w e r On . 6BNZ 1 2-3 Short : PIIX4 Disable LAN Power On . 82443BX JP11 : On-Board LAN Function (Optional) JP11 3D RAGE PRO 1 Intel SB82558B 1-2 Short : L A N Disabled . 6BNZ 1 2-3 Short : L A N Enabled . PIIX4 82443BX 19 Quick Installation Guide On-Board LAN Connector (Optional) 1 3D RAGE PRO 2 Intel SB82558B 1 - Yellow LED (LAN Active LED) 2 – Green LED (LAN Link LED) 6BNZ PIIX4 82443BX J9 : On-Board Sound Function (Optional) J9 1 3D RAGE PRO Intel SB82558B 1-2 Short : Disable On-Board Sound 6BNZ 1 PIIX4 2-3 Short : Enable On-Board Sound 82443BX 20 6BNZ Game Port / Audio Port (Optional) Audio Port 3D RAGE PRO Intel SB82558B MIC 6BNZ Line Out Line In PIIX4 CN3 Game Port 82443BX 1 CN4 : On-Board Sound CD-Line In (Optional) CN4 3D RAGE PRO Intel SB82558B ON-Board Sound Function 6BNZ PIIX4 82443BX 21 G R G L Quick Installation Guide JP10 : On-Board VGA JP10 3D RAGE PRO 1 1-2 Short : Disable On-Board VGA Intel SB82558B 6BNZ PIIX4 1 2-3 Short : Enable On-Board VGA 82443BX JP9 : Release On-Board VGA from occupying IRQ Resource (It is not to enable or disable On-Board VGA Function.) JP9 3D RAGE PRO 1 1-2 Short : Disable VGA Int. Intel SB82558B 6BNZ PIIX4 1 2-3 Short : Enable VGA Int. 82443BX 22 6BNZ JP12 : CLEAR CMOS FUNCTION JP12 1 3D RAGE PRO Intel SB82558B 1-2 Close: Clear CMOS 6BNZ 1 2-3 Close: Normal PIIX4 82443BX J14 : Internal Buzzer 3D RAGE PRO Intel SB82558B 6BNZ J14 PIIX4 Short : Enable Internal Buzzer 82443BX Open : Disable Internal Buzzer 23 Quick Installation Guide BAT1 : BATTERY 3D RAGE PRO Intel SB82558B 6BNZ PIIX4 82443BX BAT+ MDanger of explosion if battery is incorrectly replaced. MReplace only with the same or equivalent type recommended by the manufacturer. MDispose of used batteries according to the manufacturer’ s instructions. 24 6BNZ III. Top Performance Test Setting: Users have to modify the value for each item in chipset features as follow for top performance setting. ** Each value of items as above depends on your hardware configuration : CPU , SDRAM , Cards , etc. Please modify each value of items if your system does not work properly . 25 Quick Installation Guide The following performance data list is the testing results of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users. (The different Hardware & Software configuration will result in different benchmark testing results.) • CPU Pentium II processor • DRAM (128 × 2) MB SDRAM (SEC KM48S8030BT-GH) • CACHE SIZE 512 KB included in CPU • DISPLAY ATi RAGE Pro AGP Display Onboard (4MB SGRAM) • STORAGE Onboard IDE (IBM DHEA-36481) • O.S. Windows® NT 4.0 • DRIVER Display Driver at 1024 x 768 x 256 colors x 75Hz. Triones Bus Master IDE Driver 3.70 Processor Intel Pentium II 266MHz (66×4) 350MHz (100×3.5) Winbench98 CPU mark32 FPU Winmark Business Disk Hi-End Disk Business Graphics Hi-End Graphics 719 1380 1840 4370 156 171 862 1800 1900 4620 195 219 29.4 32.8 34.1 37.4 Winstone98 Business Hi-End 26