Download 6zoz user`s manual

6ZOZ
USER'S MANUAL
1.
System power on by PS/2 Mouse: First, enable this function
in CMOS Setup, then you can power on the system by double
clicking the right or left button of your PS/2 Mouse.
2.
System power on by Keyboard: If your ATX power supply
supports 300 mA 5V Stand-By current (dependent on the
specification of keyboards), you can power on your system
by entering password from the Keyboard after setting the
“Keyboard power on” jumper and password in CMOS Setup.
3.
Support Modem Ring-On (COM A and COM B).
4.
Support 3 steps ACPI LED.
5.
ATi 3D RAGE PRO graphics acceleration Onboard.
6.
YAMAHA PCI Audio chip Onboard (Optional).
7.
INTEL SB82558B LAN chip Onboard (Optional).
8.
Wake-Up on LAN. (The ATX power supply supports larger
than 720 mA 5V Stand-By current) (Optional).
Pentium  II / CeleronTM Processor MAINBOARD
R-10-01-081229
6ZOZ
3-2
The author assumes no responsibility for any errors or omissions which may
information contained herein.
Third-party brands and names are the property of their respective
Sound Blaster is a registered trademark of Creative Technology Ltd in the
are trademarks of Creative Technology Ltd.
November. 28, 1998 Taipei, Taiwan
1
Quick Installation Guide
I. Quick Installation Guide :
CPU SPEED SETUP
The default system bus speed is 66 / 100MHz. The user can select the system
bus speed (SW1) and change the DIP SWITCH (SW2) selection to set up the
CPU speed for 233 - 633MHz processor.
M The CPU speed must match with the frequency RATIO. It will cause
system hanging up if the frequency RATIO is higher than CPU's.
SW1 (ON:O / OFF:X)
SW1
AGP
133
89
124
83
112
75
100
66
83
83
75
75
66
66
1
X
O
X
X
O
O
O
2
X
O
O
X
X
O
X
3
O
O
X
X
O
X
X
4
X
X
X
X
O
O
O
SW2 (ON:O / OFF:X)
FREQ. RATIO
X3
X 3.5
X4
X 4.5
X5
X 5.5
X6
X6.5
1
O
X
O
X
O
X
O
X
DIP SWITCH (SW)
2
3
X
O
X
O
O
X
O
X
X
X
X
X
O
O
O
O
4
O
O
O
O
O
O
X
X
«Note: We don’t recommend you to setup your system speed to 75,83,
112, 124 or 133MHz because these frequencies are not the
standard specifications for CPU, Chipset and most of the
peripherals. Whether your system can run under 75, 83, 112, 124
or 133MHz properly will depend on your hardware configurations:
2
6ZOZ
CPU, SDRAM, Cards, etc.
3
Quick Installation Guide
1. Pentium II / Celeron 233 / 66MHz FSB
YAMAHA
SW1
4 3 2 1
INTEL
82558B
OFF
ON
82443
ZX
PIIX4E
SW2
BIOS
6ZOZ
1
2
3
3D RAGE
PRO
4
OFF ON
2. Pentium II / Celeron 266 / 66MHz FSB
SW2
1
2
SW1
4
3 2 1
OFF
ON
3
4
OFF ON
3. Pentium II / Celeron 300 / Celeron 300A/ 66MHz FSB
SW2
1
2
SW1
4
3 2 1
OFF
ON
3
4
OFF ON
4
6ZOZ
4. Pentium II / Celeron 333 / 66MHz FSB
SW2
1
2
SW1
4
3 2 1
OFF
ON
3
4
OFF ON
5. Pentium II / Celeron 366 / 66MHz FSB
SW2
1
2
SW1
4
3 2 1
OFF
ON
3
4
OFF ON
6. Pentium II / Celeron 400 / 66MHz FSB
SW2
1
2
SW1
4
3 2 1
OFF
ON
3
4
OFF ON
7. Pentium II / Celeron 433 / 66MHz FSB
SW2
1
2
SW1
4
3 2 1
OFF
ON
3
4
OFF ON
5
Quick Installation Guide
8. Pentium II 350 / 100MHz FSB
SW2
1
2
SW1
4
3 2 1
OFF
ON
3
4
OFF ON
9. Pentium II 400 / 100MHz FSB
SW2
1
2
SW1
4
3 2 1
OFF
ON
3
4
OFF ON
10.Pentium II 450 / 100MHz FSB
SW2
1
2
SW1
4
3 2 1
OFF
ON
3
4
OFF ON
11.Pentium II 500 / 100MHz FSB
SW2
1
2
SW1
4
3 2 1
OFF
ON
3
4
OFF ON
6
6ZOZ
12.Pentium II 550 / 100MHz FSB
SW2
1
2
SW1
4
3 2 1
OFF
ON
3
4
OFF ON
13.Pentium II 600 / 100MHz FSB
SW2
1
2
SW1
4
3 2 1
OFF
ON
3
4
OFF ON
14.Pentium II 650 / 100MHz FSB
SW2
1
2
SW1
4
3 2 1
OFF
ON
3
4
OFF ON
7
Quick Installation Guide
II. Jumper setting:
J7 : CPU FAN PWR (CPU Cooling Fan Power Connector)
YAMAHA
INTEL
82558B
82443
ZX
PIIX4E
BIOS
1
Pin No.
1
2
3
Function
GND
+12V
SENSE
3D RAGE
PRO
6ZOZ
J12 : System FAN PWR (System Cooling Fan Power Connector)
YAMAHA
INTEL
82558B
82443
ZX
PIIX4E
BIOS
1
3D RAGE
PRO
6ZOZ
8
Pin No.
1
2
3
Function
GND
+12V
SENSE
6ZOZ
PS/2 Mouse and IBM PS/2 Keyboard Connector
PS/2 Mouse
YAMAHA
YMF724
INTEL
82558B
82443
ZX
PS/2 Keyboard
PIIX4E
BIOS
PS/2
Mouse/Keyboard
Pin No. Function
Data
1
NC
2
3
GND
4
VCC (+5V)
5
Clock
6
NC
3D RAGE
PRO
6ZOZ
VGA : VGA Port
YAMAHA
YMF724
INTEL
82558B
82443
ZX
PIIX4E
BIOS
3D RAGE
PRO
6ZOZ
9
Quick Installation Guide
LPT : Printer Port
YAMAHA
YMF724
INTEL
82558B
82443
ZX
PIIX4E
BIOS
3D RAGE
PRO
6ZOZ
COM A : Serial port1
YAMAHA
INTEL
82558B
82443
ZX
PIIX4E
COM A
BIOS
3D RAGE
PRO
6ZOZ
10
6ZOZ
COM B : Serial port 2
YAMAHA
INTEL
82558B
82443
ZX
PIIX4E
COM B
BIOS
3D RAGE
PRO
6ZOZ
USB : USB Connector
YAMAHA
INTEL
82558B
82443
ZX
PIIX4E
BIOS
3D RAGE
PRO
6ZOZ
11
Quick Installation Guide
JP4 : Keyboard Power On
JP4
YAMAHA
1,2 Short :
INTEL
82558B
82443
ZX
1
Enable Keyboard Power
On.
PIIX4E
1
2,3 Short : (Default)
BIOS
Disable Keyboard Power
On.
3D RAGE
PRO
6ZOZ
JP6 : SB-LINK (Creative PCI Sound Card Support)
YAMAHA
INTEL
82558B
JP6
82443
ZX
6
5
2
1
PIIX4E
BIOS
3D RAGE
PRO
6ZOZ
12
Pin No.
1
2
3
4
5
6
Function
Signal
GND
NC
Signal
GND
Signal
6ZOZ
J11 : LAN Power On (Optional)
YAMAHA
INTEL
82558B
82443
ZX
1
1,2 Short :
PIIX4E
Enabled LAN Power On .
BIOS
1
2,3 Short : (Default)
3D RAGE
PRO
Disable LAN Power On .
6ZOZ
On-Board LAN Connector (Optional)
1
2
YAMAHA
1 - Yellow LED
(LAN Active LED)
2 – Green LED
(LAN Link LED)
INTEL
82558B
82443
ZX
PIIX4E
BIOS
3D RAGE
PRO
6ZOZ
13
Quick Installation Guide
JP13 : On-Board Sound Function (Optional)
YAMAHA
1
1,2 Short :
Disable On-Board Sound
INTEL
82558B
82443
ZX
1
PIIX4E
2,3 Short : (Default)
Enable On-Board Sound
BIOS
3D RAGE
PRO
6ZOZ
Game Port / Audio Port (Optional)
Audio Port
YAMAHA
INTEL
82558B
MIC
82443
ZX
Line Out
Line In
PIIX4E
CN3
BIOS
Game Port
3D RAGE
PRO
1
6ZOZ
14
6ZOZ
CN4 : On-Board Sound CD-Line In (Optional)
YAMAHA
CN4
INTEL
82558B
82443
ZX
ON-Board Sound Function
G
R
G
L
PIIX4E
CD-ROM
1 L
G
G
BIOS
3D RAGE
PRO
6ZOZ
JP9 : On-Board VGA
YAMAHA
INTEL
82558B
82443
ZX
JP9
1,2 Short :
PIIX4E
1
Disable On-Board VGA
BIOS
1
2,3 Short : (Default)
3D RAGE
PRO
Enable On-Board VGA
6ZOZ
15
R
Quick Installation Guide
JP8 : Release On-Board VGA from occupying IRQ Resource
(It is not to enable or disable On-Board VGA Function.)
YAMAHA
JP8
INTEL
82558B
82443
ZX
1
1,2 Short :
PIIX4E
Disable VGA INT.
BIOS
1
2,3 Short : (Default)
3D RAGE
PRO
Enable VGA INT.
6ZOZ
JP14 : Internal Buzzer
YAMAHA
INTEL
82558B
82443
ZX
Buzzer
PIIX4E
JP14
Short :
BIOS
Enable Internal Buzzer
3D RAGE
PRO
Open :
Disable Internal Buzzer
6ZOZ
16
6ZOZ
JP17 : System Acceleration
1
YAMAHA
YMF724
1-2 Turbo
2-3 100MHz Normal
Default: 2-3 100MHz Normal
INTEL
82558B
82443
ZX
1-2 Turbo:
For 100MHz Turbo and other
frequencies
PIIX4E
2-3 100MHz Normal:
For 100MHz Normal
BIOS
3D RAGE
PRO
6ZOZ
JP10 : Onboard LAN Function (Optional)
YAMAHA
1
1,2 short
Onboard LAN Disable.
INTEL
82558B
82443
ZX
PIIX4E
1
2,3 short (Default)
Onboard LAN Enable.
BIOS
3D RAGE
PRO
6ZOZ
17
Quick Installation Guide
JP20 : Suspend To RAM Function (Optional)
YAMAHA
YMF724
Short :
Enable
INTEL
82558B
Open :
Suspend To RAM Function.
Normal Operation.
82443
ZX
M When STR function is Enabled, please
PIIX4E
do not unplug the SDRAM modules, for it
will burn the SDRAMs and mainboard .
BIOS
3D RAGE
PRO
6ZOZ
M Support under Windows 98 ACPI O.S.
M When use STR function ,it’s depends on VGA brand version .
JP19 : STR LED (Optional)
YAMAHA
INTEL
82558B
82443
ZX
PIIX4E
BIOS
+ −
3D RAGE
PRO
6ZOZ
18
6ZOZ
JP18 : CLEAR CMOS Function
YAMAHA
INTEL
82558B
82443
ZX
PIIX4E
1
BIOS
3D RAGE
PRO
1-2 Short :Clear CMOS
2-3 Short :Normal
Default: 2-3 Short
6ZOZ
JP7 : CASE OPEN
YAMAHA
INTEL
82558B
82443
ZX
1
PIIX4E
Pin No. Function
BIOS
3D RAGE
PRO
6ZOZ
19
1
Signal
2
GND
Quick Installation Guide
TEL : For Modem with internal voice connector(Optional).
1
YAMAHA
INTEL
82558B
82443
ZX
PIIX4E
BIOS
3D RAGE
PRO
6ZOZ
BAT1 : BATTERY
YAMAHA
INTEL
82558B
82443
ZX
PIIX4E
BIOS
3D RAGE
PRO
+
−
6ZOZ
MDanger of explosion if battery is incorrectly replaced.
MReplace only with the same or equivalent type recommended by the
manufacturer.
MDispose of used batteries according to the manufacturer’ s instructions.
20
6ZOZ
III. Top Performance Test Setting:
Users have to modify the value for each item in chipset features as follow
for top performance setting.
**
Each value of items as above depends on your hardware configuration :
CPU , SDRAM , Cards , etc.
Please modify each value of items if your system does not work properly .
The following performance data list is the testing results of some popular
21
Quick Installation Guide
benchmark testing programs.
These data are just referred by users, and there is no responsibility for different
testing data values gotten by users. (The different Hardware & Software
configuration will result in different benchmark testing results.)
• CPU
Pentium II 450MHz / CeleronTM 366 MHz processor
• DRAM
(128 × 1) MB SDRAM (SEC KM48S8030BT-GH)
• CACHE SIZE
Included in CPU
• DISPLAY
On-Board ATi 3D RAGE Pro 2X AGP Display
(4MB SGRAM)
• STORAGE
Onboard IDE (Seagate ST34520A)
• O.S.
Windows® NT 4.0 (SPK4)
• DRIVER
Display Driver at 1024 x 768 x 64 colors x 75Hz.
Triones Bus Master IDE Driver 3.70
Processor
Intel CeleronTM
Intel Pentium II
450MHz (100×4.5) 366MHz (66×5.5)
Winbench99
CPU mark32
FPU Winmark
Business Disk
Hi-End Disk
Business Graphics
Hi-End Graphics
1110
2300
4370
10500
142
333
772
1970
4240
10400
126
299
29.5
28.8
26
24.4
Winstone99
Business
Hi-End
22