Download Eval Kit User Manual - Janus Remote Communications

Terminus Plug-In Modules
Evaluation Kit User Guide
Bulletin
Revision
Date
JA03-EKUM
P04
26 Aug 2013
INTRODUCTION
The following document describes the functions of the evaluation board for the Terminus Plug-In series of
cellular communication terminals. This guide, along with the Plug-In Modules Hardware User guide, allows
all features of the terminal to be evaluated before your PCB goes into CAD.
Be advised that there is an evaluation kit for each of the Plug-In Modules available on the Janus website.
These kits supply all the accessories required to evaluate the chosen terminal.
INTERFACES
Power Supply
The Evaluation Board requires 5VDC to power the evaluation PCB and Terminus module. The evaluation
board has two power supply connection options: center positive barrel connector or terminal block
direct wire connection.
The Evaluation Board is equipped with protection circuitry to prevent reverse voltage, as well as help
with protection from transients. The board can withstand a reverse voltage of 60V and a peak voltage of
80V. The circuitry is set to clip any input greater than 6V to a safe level.
Any input above 6V will read for a set period, and if before 20 mS has not returned to safe level, the
over-voltage protection will activate and turn off the output.
To re-enable the output, power must be cycled or the SWITCHER_EN pin (DIP pos. 7) must be pulled
low at least 100 µS and then released.
Power supply requirement:
Voltage:
5Vdc ± 5%
Power:
10W peak
RS-232 Serial Ports
The Evaluation board for the Plug-In terminals has three RS-232 serial ports.
AT COMMAND PORT:
This port is available to send AT commands to GSM, CDMA, UMTS, EV-DO, and HSPA+ terminals.
Please refer to the Terminus Plug-In User Guide for serial port details for the specific terminal you are
evaluating.
Typical Port Settings:
Baud:
115200
Data bits:
8
Parity:
None
Stop Bits:
1
Hardware Handshaking: CTS/RTS
Terminus Plug-In Modules Evaluation Kit User Guide
Page 2
Rev: P04
Date: 08/26/13
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
All Rights Reserved See website for latest revision.
Not intended for life support applications.
RS-232 SERIAL PORTS continued…
TRACE PORT:
This port is used by the GSM865CF and HSPA910CF terminals and is used for debug and local
firmware upgrades of the GSM modules radio firmware. This port is not needed for Python script
upload, however, during development of Python scripts this port should be used to receive debug
‘print’ statements. Hardware handshaking is not available on this port.
Port Settings:
Baud:
115200
Data bits:
8
Parity:
None
Stop Bits:
1
Hardware Handshaking: N/A
NAVSYNC MS20 GPS NMEA PORT:
This port is used exclusively by the GSM865CF terminal and is used to communicate with the MS20
GPS module. The MS20 GPS module is populated on the GSM865CF by option. Refer to Hardware
User Guide for ordering information. Hardware handshaking is not available on this port.
Port Settings:
Baud:
9600
Data bits:
8
Parity:
None
Stop Bits:
1
Hardware Handshaking: N/A
USB SERIAL PORTS:
The evaluation board for the Plug-In Terminus family allows access to virtual COM ports and modem
ports via the USB. All of the Plug-In Terminus units support the USB interface except the GSM865CF.
To use this interface during development you will need to download the USB drivers from the Janus
website (www.janus-rc.com). Please note that in order for proper power on sequencing, the main
power must be activated first. The USB VCC line must be disconnected until the device is on, otherwise
it may not power up correctly or properly install the USB drivers.
CDMA864CF, EVDO910CF, CDMA910CF, UMTS864CF USB Ports
AUXILLARY PORT:
This port is available to send AT commands to GSM, CDMA and UMTS terminals. Please refer to the
Plug-In User Guide for serial port details for the specific terminal you are evaluating.
Typical Port Settings:
Baud:
Data bits:
Parity:
Stop Bits:
Hardware Handshaking:
115200
8
None
1
CTS/RTS
Terminus Plug-In Modules Evaluation Kit User Guide
Page 3
Rev: P04
Date: 08/26/13
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
All Rights Reserved See website for latest revision.
Not intended for life support applications.
USB Serial Ports continued…
TRACE PORT:
This port is used for debug and local firmware upgrades of the cellular modules radio firmware.
Hardware handshaking is not available on this port.
Port Settings:
Baud:
115200
Data bits:
8
Parity:
None
Stop Bits:
1
Hardware Handshaking: N/A
TELIT GPS NMEA PORT:
This port is used to communicate with Telit’s integrated GPS hardware. Please refer to Telit AT
command guide for available settings and features to implement this port in your hardware design.
Hardware handshaking is not available on this port.
Port Settings:
Baud:
115200
Data bits:
8
Parity:
None
Stop Bits:
1
Hardware Handshaking: N/A
HSPA910CF USB Ports
The HSPA910CF will show several virtual COM ports after the drivers are installed. These are USB0
through USB6, along with a modem for applications like Dial Up with Windows. This allows for
applications like simultaneous AT commands, voice calls, and Python tracing.
These ports can be configured in various ways depending on the user’s application, but by default
USB0 and USB3 are AT command ready after enumeration.
Typical Port Settings:
Baud:
Data bits:
Parity:
Stop Bits:
Hardware Handshaking:
115200
8
None
1
N/A
You will want to reference HSPA910CF Ports Arrangements 4f.pdf for full details on using the
AT#PORTCFG command.
Terminus Plug-In Modules Evaluation Kit User Guide
Page 4
Rev: P04
Date: 08/26/13
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
All Rights Reserved See website for latest revision.
Not intended for life support applications.
EVALUATION KIT BOARD DETAILS
Telit Trace
Port
MS20 GPS
NMEA Port
AT Command
Port
MCX
Connector
Dip
Switches
SMA
Connector
Plug-In Module
Connector
General
Purpose I/O
Connections
J1 Jumper
Handset Analog Audio
USB Port
Power IN
(2.1mm barrel connector)
MS20 Reset
Power IN
Terminal Block Connection
Cellular ON-OFF
Cellular Reset
Terminus Plug-In Modules Evaluation Kit User Guide
Page 5
Rev: P04
Date: 08/26/13
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
All Rights Reserved See website for latest revision.
Not intended for life support applications.
GENERAL PURPOSE I/O:
The Evaluation board for the Plug-In series terminals expose the following I/O via terminal block wire
connection.
CMOS GPIO
1 through 7
ADC
1&2
DAC
1
VAUX
I/O Reference Voltage
Please refer to Hardware user guide before making connection to any of these I/Os. Each module has
specific requirements for these I/O.
SWITCHES:
DIP SWITCHES:
The evaluation board has an 8 position DIP switch that allows selection of various modes of operation.
Please refer to table below for definition of switch functions:
Name
Function Description
MODE0
MODE1
MODE2
MODE3
MODE4
SERVICE
SWITCHER_EN
ENABLE
Disables the RS-232 Line Drivers. This allows for direct connection to CMOS UART I/O.
Tri-States all Evaluation board I/Os directly connected to the Plug-In Terminus.
This allows the module to be shutdown and not reverse bias the terminals I/O.
Cross connect of the TRACE and NAVSYNC_GPS signals for Null Modem configuration. This functionality is used specifically on the GSM865CF for the Python GPS Demo.
Not implemented
Not implemented
Not implemented
For use with the GSM865CF
Enabling this switch allows local radio Firmware update via the Trace Serial Port.
Enable input of the Evaluation Board
Enable input of the Plug-In terminal
Active Position
ON
ON
N/A
N/A
N/A
N/A
OFF
OFF
All switches should be in the off position in order to turn-on Plug-In terminal and send AT commands via
the RS-232 serial port.
PUSH BUTTON SWITCHES:
The evaluation board has three push buttons to control the state of the Plug-In terminal populated on
the board.
GSM ON_OFF:
Used to toggle the on off state of the Plug-In terminal. On power up, the Evaluation PCB will toggle
ON-OFF triggering the terminal to power up. To turn the terminal on or off, press the switch for two
seconds and release.
GSM RESET:
Used to recover operation of Plug-In terminal in case of unexpected error resulting in the inability of the
application to communicate with the terminal.
MS20 GPS RESET:
This switch is used exclusively by the GSM865CF terminal and is used to reset the GPS module in case
of unexpected error resulting in the inability of the application to communicate with the GPS receiver.
Terminus Plug-In Modules Evaluation Kit User Guide
Page 6
Rev: P04
Date: 08/26/13
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
All Rights Reserved See website for latest revision.
Not intended for life support applications.
RF CONNECTORS
The evaluation board comes equipped with RF connectors to interface Plug-In terminal with Cellular and
GPS antennas. The Plug-In terminals have their RF connections exposed via Murata GSC connectors.
The evaluation kits come with the terminals Cellular and GPS interfaces connected via a GSC-to-GSC RF
patch cable to the Evaluation board.
SMA TO MURATA GSC CONNECTOR:
The SMA connector allows for a standard cellular antenna to be attached directly to the evaluation
board.
MCX TO MURATA GSC CONNECTOR:
The MCX connector allows for a standard active GPS antenna to be attached directly to the evaluation
board.
EVALUATION BOARD POWER JUMPER SELECTION
The power supply that supplies power to the evaluation boards active components can be selected from
two different sources.
For ease of connection, the evaluation boards active components can be powered from the main power
supply input. In this configuration it is not possible to evaluate the current consumption of the Plug-In
Module without also including the active components of the evaluation board.
In order to evaluate the power consumption of the Plug-In modules without the added consumption of the
evaluation boards active components, the evaluation board must be powered via the USB terminal.
J1 Jumper Selection:
Shunt Location
Evaluation Board Power Supply Source
Pin1 <-> Pin 2
Pin3 <-> Pin 2
Evaluation Boards active components powered from main supply connector.
Evaluation Boards active components powered from USB connector.
Note:
If the USB configuration is used, please note that only the evaluation board and a majority of it’s components will be powered by the USB. The
attached CF module and evaluation board protection circuitry will not be and will still need to draw it’s power from the main “Power In” screw
terminals or barrel jack. The protection circuitry will add a draw of roughly 1.5mA.
Also note that in order for proper power up operation, the USB power should be attached after the main supply is already attached and powered.
In order to take full advantage of the Pin 2-3 positioning for USB enabled Plug-In Terminus modems on
the v3.xx evaluation boards, some minor hardware modifications need to be made. Please contact Janus
for additional information.
Terminus Plug-In Modules Evaluation Kit User Guide
Page 7
Rev: P04
Date: 08/26/13
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
All Rights Reserved See website for latest revision.
Not intended for life support applications.
GSM865CF GETTING STARTED
This will take you through the initial steps required that will allow AT Commands to be sent to the
GSM865CF Plug-In module.
Step 1
Please confirm that you have these items, and that your Evaluation Board is correctly set:
Power supply with 2.1mm barrel connector termination
6’ RS232 cable
USB to Serial adapter cable
Jumper Shunt
Cellular Antenna
GSC to GSC patch cable(s)
Make sure that the DIP switches on the Evaluation Board are all set to OFF.
Step 2
If not done already, plug the GSM865CF Plug-In Module into the connectors at the center of the
Evaluation Board, being sure to align the pins properly. Take note that to make the alignment easier, the
two connectors are of different lengths.
Step 3
Cellular: Use one of the included GSC to GSC patch cables and attach one end to P5 on the
GSM865CF and the other end to P15 of the evaluation board. Then attach the cellular antenna to the
SMA edge mount connector of the evaluation board.
GPS (if applicable): Use one of the included GSC to GSC patch cables and attach one end to P4 on
the GSM865CF and the other end to P15 on the evaluation board. Then attach the GPS antenna to the
MCX edge mount connector of the evaluation board.
Step 4
Connect the RS232 cable to the AT COMMAND
port, labeled P8. Connect the other end to an
available serial port on your PC, or an available
USB port by use of the serial to USB adapter.
Step 5
Place jumper shunt across Pin 1 and Pin 2 of
Jumper J1.
Step 6
Plug in your power supply to the 2.1mm barrel
connector on the board, labeled P1. After
roughly 2 seconds you should see the STATUS
LED, labeled D7, start blinking. This lets you
know that the Plug-In Module is powered and
functioning.
Step 7
Open HyperTerminal and start a new session.
Use the drop down box to select the COM port
that your serial cable is plugged into.
Terminus Plug-In Modules Evaluation Kit User Guide
Page 8
Rev: P04
Date: 08/26/13
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
All Rights Reserved See website for latest revision.
Not intended for life support applications.
GSM865CF GETTING STARTED continued
Step 7 continued
Then select “Configure,” and select these settings:
Bits per second: 115200
Data bits: 8
Parity: None
Stop bits: 1
Flow control: Hardware
Then press “OK.”
Step 7
Click on the “Call” button in HyperTerminal to make the connection. In the window you should now be
able to send AT commands. To make sure you have a proper connection, type “AT” into the window,
and press Enter. You should receive a response of “OK”.
If you do not receive that response, go back and check to make sure you’ve selected the correct COM
port, as well as the settings.
If you receive an OK, your connection is successful and you are now able to communicate with
the module. Please refer to http://www.janus-rc.com/terminuscf.html for a link to the proper Telit
documentation.
The “Telit Module Software User Guide” will give step by step instructions on setting up voice and data
calls, SMS messages, and socket connections.
The “Telit AT Reference Guide” is a full list of supported AT commands and their functions.
Terminus Plug-In Modules Evaluation Kit User Guide
Page 9
Rev: P04
Date: 08/26/13
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
All Rights Reserved See website for latest revision.
Not intended for life support applications.
CDMA864CF GETTING STARTED
This will take you through the initial steps required that will allow AT Commands to be sent to the
CDMA864CF Plug-In module. This example uses the USB interface, but alternatively a serial connection
to the AT Command DB9 for this may be faster and more suitable for you.
Step 1
Please confirm that you have these items, and that your Evaluation Board is correctly set:
Power supply with 2.1mm barrel connector termination
3’ USB cable
Jumper Shunt
Cellular Antenna
GSC to GSC patch cable
Make sure that the DIP switches on the Evaluation Board are all set to OFF.
Step 2
If not done already, plug the CDMA864CF Plug-In module into the connectors at the center of the
Evaluation Board, being sure to align the pins properly. Take note that to make the alignment easier, the
two connectors are of different lengths.
Step 3
Cellular: The CDMA864CF has a short cable with a
SMA end; simply attach the cellular antenna to the
end of that cable.
GPS (if applicable): Use one of the included GSC
to GSC patch cables and attach one end to the
top GSC connector on the CC864-D module, and
the other end to P15 on the evaluation board.
Then attach the GPS antenna to the MCX edge
mount connector of the evaluation board.
Step 4
Place jumper shunt across Pin 1 and Pin 2 of
Jumper J1.
Step 5
Plug in your power supply to the 2.1mm barrel
connector on the board, labeled P1. After roughly
2 seconds you should see the STATUS LED,
labeled D7, start blinking. This lets you know that
the Plug-In module is powered and functioning.
Step 6
Connect the USB cable to the USB port on the
Evaluation Board. Connect the other end to an
available USB port on your PC.
Terminus Plug-In Modules Evaluation Kit User Guide
Page 10
Rev: P04
Date: 08/26/13
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
All Rights Reserved See website for latest revision.
Not intended for life support applications.
CDMA864CF GETTING STARTED continued
Step 7
You should see the following ports in the Windows™ Device Manager:
Telit Auxiliary Port
Telit Diagnostics Interface
Telit NMEA Port
If these do not become available, or you see an error message, this means you need to install the USB
drivers for the CDMA864CF. Please refer to http://www.janus-rc.com/terminuscf.html for the proper
drivers before continuing.
Step 8
Open HyperTerminal or a similar terminal emulator and start a new session. Use the drop down box to
select the COM port that corresponds to the Telit Auxiliary Port.
Then select “Configure,” and select these settings:
Bits per second: 115200
Data bits: 8
Parity: None
Stop bits: 1
Flow control: Hardware
Then press “OK.”
Step 8
Click on the “Call” button in HyperTerminal to make the connection. In the window you should now be
able to send AT commands. To make sure you have a proper connection, type “AT” into the window,
and press Enter. You should receive a response of “OK”.
If you do not receive that response, go back and check to make sure you’ve selected the correct COM
port, as well as the settings.
If you receive an OK, your connection is successful and you are now able to communicate with
the module. Please refer to http://www.janus-rc.com/terminuscf.html for a link to the proper Telit
documentation.
The “Telit Module Software User Guide” will give step by step instructions on setting up voice and data
calls, SMS messages, and socket connections.
The “Telit AT Reference Guide” is a full list of supported AT commands and their functions.
Terminus Plug-In Modules Evaluation Kit User Guide
Page 11
Rev: P04
Date: 08/26/13
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
All Rights Reserved See website for latest revision.
Not intended for life support applications.
UMTS864CF GETTING STARTED
This will take you through the initial steps required that will allow AT Commands to be sent to the
UMTS864CF Plug-In module. This example uses the USB interface, but alternatively a serial connection to
the AT Command DB9 for this may be faster and more suitable for you.
Step 1
Please confirm that you have these items, and that your Evaluation Board is correctly set:
Power supply with 2.1mm barrel connector termination
3’ USB cable
Jumper Shunt
Cellular Antenna
GSC to GSC patch cable(s)
Make sure that the DIP switches on the Evaluation Board are all set to OFF.
Step 2
If not done already, plug the UMTS864CF Plug-In module into the connectors at the center of the
Evaluation Board, being sure to align the pins properly. Take note that to make the alignment easier, the
two connectors are of different lengths.
Step 3
Cellular: The UMTS864CF has a short cable
with a SMA end; simply attach the cellular
antenna to the end of that cable.
GPS (if applicable): Use one of the included
GSC to GSC patch cables and attach one end
to the top GSC connector on the UC864-G
module, and the other end to P15 on the
evaluation board. Then attach the GPS antenna
to the MCX edge mount connector of the
evaluation board.
Step 4
Place jumper shunt across Pin 1 and Pin 2 of
Jumper J1.
Step 5
Plug in your power supply to the 2.1mm barrel
connector on the board, labeled P1. After roughly 2
seconds you should see the STATUS LED, labeled
D7, start blinking. This lets you know that the PlugIn module is powered and functioning.
Step 6
Connect the USB cable to the USB port on the
Evaluation Board. Connect the other end to an
available USB port on your PC.
Terminus Plug-In Modules Evaluation Kit User Guide
Page 12
Rev: P04
Date: 08/26/13
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
All Rights Reserved See website for latest revision.
Not intended for life support applications.
UMTS864CF GETTING STARTED continued
Step 7
You should see the following ports in the Windows™ Device Manager:
Telit Auxiliary Port
Telit Diagnostics Interface
Telit NMEA Port
If these do not become available, or you see an error message, this means you need to install the USB
drivers for the UMTS864CF. Please refer to http://www.janus-rc.com/terminuscf.html for the proper
drivers before continuing.
Step 8
Open HyperTerminal or a similar terminal emulator and start a new session. Use the drop down box to
select the COM port that corresponds to the Telit Auxiliary Port.
Then select “Configure,” and select these settings:
Bits per second: 115200
Data bits: 8
Parity: None
Stop bits: 1
Flow control: Hardware
Then press “OK.”
Step 9
Click on the “Call” button in HyperTerminal to make the connection. In the window you should now be
able to send AT commands. To make sure you have a proper connection, type “AT” into the window,
and press Enter. You should receive a response of “OK”.
If you do not receive that response, go back and check to make sure you’ve selected the correct COM
port, as well as the settings.
If you receive an OK, your connection is successful and you are now able to communicate with
the module. Please refer to http://www.janus-rc.com/terminuscf.html for a link to the proper Telit
documentation.
The “Telit Module Software User Guide” will give step by step instructions on setting up voice and data
calls, SMS messages, and socket connections.
The “Telit AT Reference Guide” is a full list of supported AT commands and their functions.
Terminus Plug-In Modules Evaluation Kit User Guide
Page 13
Rev: P04
Date: 08/26/13
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
All Rights Reserved See website for latest revision.
Not intended for life support applications.
HSPA910CF GETTING STARTED
This will take you through the initial steps required that will allow AT Commands to be sent to the
HSPA910CF Plug-In module. This example uses the USB interface, but alternatively a serial connection to
the AT Command DB9 for this may be faster and more suitable for you.
Step 1
Please confirm that you have these items, and that your Evaluation Board is correctly set:
Power supply with 2.1mm barrel connector termination
3’ USB cable
Jumper Shunt
Cellular Antenna
GSC to GSC patch cable(s)
Make sure that the DIP switches on the Evaluation Board are all set to OFF.
Step 2
If not done already, plug the HSPA910CF PlugIn module into the connectors at the center of
the Evaluation Board, being sure to align the pins
properly. Take note that to make the alignment easier,
the two connectors are of different lengths.
Step 3
Cellular: Use one of the included GSC to GSC patch
cables and attach one end to P5 on the HSPA910CF
and the other end to P14 of the evaluation board.
Then attach the cellular antenna to the SMA edge
mount connector of the evaluation board.
GPS: Use one of the included GSC to GSC patch
cables and attach one end to P6 on the HSPA910CF
and the other end to P14 on the evaluation board.
Then attach the GPS antenna to the MCX edge
mount connector of the evaluation board.
Step 4
Place jumper shunt across Pin 1 and Pin 2 of
Jumper J1.
Step 5
Plug in your power supply to the 2.1mm barrel
connector on the board, labeled P1. After roughly 2
seconds you should see the STATUS LED, labeled
D7, start blinking. This lets you know that the PlugIn module is powered and functioning.
Step 6
Connect the USB cable to the USB port on the
Evaluation Board. Connect the other end to an
available USB port on your PC.
Terminus Plug-In Modules Evaluation Kit User Guide
Page 14
Rev: P04
Date: 08/26/13
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
All Rights Reserved See website for latest revision.
Not intended for life support applications.
HSPA9104CF GETTING STARTED continued
Step 7
You should see the following ports in the Windows™ Device Manager:
USB1
USB2
USB3
USB4
USB5
USB6
If these do not become available, or you see an error message, this means you need to install the USB
drivers for the HSPA910CF. Please refer to http://www.janus-rc.com/terminuscf.html for the proper
drivers before continuing.
Step 8
Open HyperTerminal or a similar terminal emulator and start a new session. Use the drop down box to
select the COM port that corresponds to the USB3.
Then select “Configure,” and select these settings:
Bits per second: 115200
Data bits: 8
Parity: None
Stop bits: 1
Flow control: Hardware
Then press “OK.”
Step 9
Click on the “Call” button in HyperTerminal to make the connection. In the window you should now be
able to send AT commands. To make sure you have a proper connection, type “AT” into the window,
and press Enter. You should receive a response of “OK”.
If you do not receive that response, go back and check to make sure you’ve selected the correct COM
port, as well as the settings.
If you receive an OK, your connection is successful and you are now able to communicate with
the module. Please refer to http://www.janus-rc.com/terminuscf.html for a link to the proper Telit
documentation.
The “Telit Module Software User Guide” will give step by step instructions on setting up voice and data
calls, SMS messages, and socket connections.
The “Telit AT Reference Guide” is a full list of supported AT commands and their functions.
Terminus Plug-In Modules Evaluation Kit User Guide
Page 15
Rev: P04
Date: 08/26/13
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
All Rights Reserved See website for latest revision.
Not intended for life support applications.
EVDO910CF GETTING STARTED
This will take you through the initial steps required that will allow AT Commands to be sent to the
EVDO910CF Plug-In Module. This example uses the USB interface, but alternatively a serial connection to
the AT Command DB9 for this may be faster and more suitable for you.
Step 1
Please confirm that you have these items, and that your Evaluation Board is correctly set:
Power supply with 2.1mm barrel connector termination
3’ USB cable
Jumper Shunt
Cellular Antenna
GSC to GSC patch cable(s)
Make sure that the DIP switches on the Evaluation Board are all set to OFF.
Step 2
If not done already, plug the EVDO910CF Plug-In Module into the connectors at the center of the
Evaluation Board, being sure to align the pins properly. Take note that to make the alignment easier, the
two connectors are of different lengths.
Step 3
Cellular: Use one of the included GSC to GSC
patch cables and attach one end to P5 on
the EVDO910CF and the other end to P15 of
the evaluation board. Then attach the cellular
antenna to the SMA edge mount connector of
the evaluation board.
GPS: Use one of the included GSC to GSC
patch cables and attach one end to P6 on the
EVDO910CF and the other end to P15 on the
evaluation board. Then attach the GPS antenna
to the MCX edge mount connector of the
evaluation board. .
Step 4
Place jumper shunt across Pin 1 and Pin 2 of
Jumper J1.
Step 5
Plug in your power supply to the 2.1mm barrel
connector on the board, labeled P1. After roughly 2
seconds you should see the STATUS LED, labeled
D7, start blinking. This lets you know that the PlugIn module is powered and functioning.
Step 6
Connect the USB cable to the USB port on the
Evaluation Board. Connect the other end to an
available USB port on your PC.
Terminus Plug-In Modules Evaluation Kit User Guide
Page 16
Rev: P04
Date: 08/26/13
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
All Rights Reserved See website for latest revision.
Not intended for life support applications.
EVDO910CF GETTING STARTED continued
Step 7
You should see the following ports in the Windows™ Device Manager:
Telit Auxiliary Port
Telit Diagnostics Interface
Telit NMEA Port
If these do not become available, or you see an error message, this means you need to install the USB
drivers for the EVDO910CF. Please refer to http://www.janus-rc.com/terminuscf.html for the proper
drivers before continuing.
Step 8
Open HyperTerminal or a similar terminal emulator and start a new session. Use the drop down box to
select the COM port that corresponds to the Telit Auxiliary Port.
Then select “Configure,” and select these settings:
Bits per second: 115200
Data bits: 8
Parity: None
Stop bits: 1
Flow control: Hardware
Then press “OK.”
Step 9
Click on the “Call” button in HyperTerminal to make the connection. In the window you should now be
able to send AT commands. To make sure you have a proper connection, type “AT” into the window,
and press Enter. You should receive a response of “OK”.
If you do not receive that response, go back and check to make sure you’ve selected the correct COM
port, as well as the settings.
If you receive an OK, your connection is successful and you are now able to communicate with
the module. Please refer to http://www.janus-rc.com/terminuscf.html for a link to the proper Telit
documentation.
The “Telit Module Software User Guide” will give step by step instructions on setting up voice and data
calls, SMS messages, and socket connections.
The “Telit AT Reference Guide” is a full list of supported AT commands and their functions.
Terminus Plug-In Modules Evaluation Kit User Guide
Page 17
Rev: P04
Date: 08/26/13
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
All Rights Reserved See website for latest revision.
Not intended for life support applications.
Terminus Plug-In Modules Evaluation Kit User Guide
All Rights Reserved See website for latest revision.
FB2
530ohm @ 100Mhz, 3A
S-524-M1-G
P1
2mm Barrel Connector
XT-235
PJ-002A
1
2
3
C5
0.1 uF
OMIT
100V
D1
TVS (SMAJ58CA)
OMIT
Page 18
Rev: P04
VCC3.3
R3
10K, 5%
OMIT
1
2
3
R10
0
OMIT
R4
10, 5%
OMIT
Datasheet recommends 51.1k
resistance from ADJ to GND
225mV Max dropout
50mA Max output
U21
LP2980IM5-ADJ
K-582-G
1 VIN
Vo 5
3 EN
2 GND ADJ 4
C10
0.1 uF
OMIT
16V
EN
FLT
9
8
4
3
2
USB_VBUS
R40
51.1K, 1%
R-983-G
C66
6.8pF, +-.25pF
C-613
50V
C65
10uF
C-665-G
6.3V
VBANK1
C13
330pF
OMIT
50V
C6
2.2uF
C-686
6.3V
3
1
EN
Vin
NC
Vout
4
5
SHUTDOWN
ERROR
SENSE
OUTPUT
U2
TPS72218
K-364-M1-G
BYPASS
NC
GND
INPUT
2 and 3 for USB VCC
G1
G2
G3
H1
H2
H3
H5
A5
A6
A7
B5
B6
B7
C5
C6
C7
D1
D2
D3
D4
D5
D6
D7
E1
E2
E3
E4
E5
E6
E7
F6
R12
1M, 5%
OMIT
SW_ENABLE
C17
0.22 uF
OMIT
50V
VIN (MAX) = 36V
J1
1x3 Header (0.1" x 0.1")Silk Screen:
XT-463-G
EVAL BOARD POWER SELECT
PIN JUMPER SETTINGS:
1 and 2 for wall input
C12
10uF, 20%
OMIT
50V
VCC3.3
C3
10uF, 10%
C-841-G
16V
1
2
3
4
U1
LDO (LP2989-ILD-3.3 /NOPB)
K-489-G
Vo
Vo
Vo
Vo
Vo
Vo
Vo
Vo
Vo
Vo
Vo
Vo
GND
GND
GND
GND
GND
AUX
GND
BIAS
GND
GND Pgood
GND
GND
GND
GND
GND SHARE
GND
GND
GND
GND
GND
ADJ
GND
SYNC
GND
GND
GND
GND
RT
GND
RUN/SS
Vin
Vin
Vin
Vin
Vin
Vin
U5
LTM8023EV#PBF
OMIT
G7
H7
G6
F7
H6
F5
G5
A1
A2
A3
A4
B1
B2
B3
B4
C1
C2
C3
C4
EN tied to VCC3.3 so LDO U4
never turns OFF
LDO (LP2982AIM5-3.0)
K-584-M1-G
1 VIN
VCC3.3
Vo 5
3 EN
2 GND BYPASS 4
C8
2.2uF
C-686
6.3V
VCC_IN
C1
10nF, 5%
C-241-G
50V
3 position header to select which
power input the Eval Board
circuitry will use. 5V_IN is the
(post protection) barrel
connector input, USB_VBUS is the
USBVCC line from the USB B
connection.
1
2
3
5V_IN
FB3
530ohm @ 100Mhz, 3A
S-524-M1-G
C11
0.1 uF
OMIT
50V
R11
0.68, 1%, 0.5W
OMIT
C2
22uF (EMVA350ADA220ME55G)
OMIT
35V
VIN_PROTECT
5V_IN
VCC_IN
R9
4.99K, 1%
OMIT
R7
100K, 1%
OMIT
R1 = 56.2K, R2 = 51.1K
VOUT = 1.23 + 1.23(R1/R2)
VOUT = 2.58v
SW_ENABLE
R39
56.2K, 1%
R-981-G
VIH CMOS Levels:
GE865: 2.1 - 3.0v
UC864: 2.0 - 2.9v
CC865: 1.69 - 2.9v
F1
0154005.DR
MC-0148-G
IN+
Aout
SHDN
SNS
VCC
R5
10, 5%
OMIT
Q2
IRLR2908PBF
OMIT
4
3
GATE
OUT
FB
R6
1M, 5%
OMIT
U3
LTC4356IDE-3#PBf
OMIT
SW_ENABLE
12
11
7
5
6
Q3
MMBT3904
OMIT
1
P20
CON3 (1716030000)
XT-454-G
D2
1N4148WS
OMIT
sensesense+
C64
10uF
C-665-G
6.3V
SWITCHER_ENABLE
VIN
SWITCHER_ENABLE
R8
1M, 5%
OMIT
1
2
R2
10, 5%
OMIT
Q1
IRLR2908PBF
OMIT
3
4
1
R1
12mOhm, 500mW (LVK12R012FER)
OMIT
TMR
1
GND
GNDpad
10
13
GND
2
8
7
6
5
R14
49.9K, 1%
OMIT
R13
93.1K, 1%
OMIT
C14
0.1 uF
OMIT
16V
C9
0.01 uF
C-522-G
50V
C7
2.2uF
C-686
6.3V
VMIC
C15
10uF, 20%
OMIT
25V
C38
10uF
C-665-G
6.3V
C4
10uF, 10%
C-841-G
16V
VCC3.3
C16
10uF, 20%
OMIT
25V
5V_IN
FB1
530ohm @ 100Mhz, 3A
OMIT
SHDN tied to VCC_IN so LDO never
turns OFF
VCC1.8
VCC_IN
SCHEMATICS:
2
1
APPENDIX
Figure 1: Power Supply
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
Date: 08/26/13
Not intended for life support applications.
MIC+
MICEAR+
EAR-
PWRMON
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Terminus Plug-In Modules Evaluation Kit User Guide
R18
680
R-645-G
1
2
D7
YELLOW
S-214
GPS_LED
1
1
1
2
3
10k
47k
Q4
PEMH15
S-560-G
Page 19
All Rights Reserved See website for latest revision.
Rev: P04
TRACE_TX
TRACE_RX
GPS_LED
GSM_LED
SERVICE
PWRMON
O N_OFF
GSM_RESET
MIC+
MICEAR+
EAR-
ENABLE
GSM_RX
GSM_DSR
GSM_CTS
GSM_RING
GSM_DCD
GSM_TX
GSM_DTR
GSM_RTS
5V_IN
10k
6
5
4
GSM_LED
GPIO5
GPIO6
GPIO7
GPS_RESET
GPS_TX
GPS_RX
I2C_SCL
I2C_SDA
USB_ID
USB_VBUS
USB_D+
USB_D-
VAUX
VRTC
AD C1
AD C2
DAC
GPIO1
GPIO2
GPIO3
GPIO4
GPIO5
GPIO6
GPIO7
GPS_RESET
GPS_TX
GPS_RX
I2C_SCL
I2C_SDA
USB_ID
USB_VBUS
USB_D+
USB_D-
VAUX
VRTC
AD C1
AD C2
DAC
GPIO1
GPIO2
GPIO3
GPIO4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
VCC_IN
DAC
R24
12.1K
R-391
2
C54
0.1 uF
C-561-G
16V
C53
0.1 uF
C-561-G
16V
2
C25
0.01 uF
C-522-G
50V
GSM_RESET
C24
0.01 uF
C-522-G
50V
C55
0.1 uF
C-561-G
16V
C20
0.33 uF
C-667-G
10V
D5
SP0505BAJT
S-273
R38
13.7k, 1%
OMIT
R37
0 ohm
R-606-G
VRTC
1
2
3
P21
CON3 (1716030000)
XT-454-G
C21
0.01 uF
C-522-G
50V
SWITCHER_ENABLE
ENABLE
MODE0
SERVICE_IN
GSM_RESET
O N_OFF
GPS_RESET
PWRMON
GSM_LED
GPS_LED
GPIO1
GPIO2
GPIO3
GPIO4
GPIO5
GPIO6
GPIO7
ENABLE
MODE0
SERVICE_IN
GSM_RESET
ON_OFF
GPS_RESET
PWRMON
GSM_LED
GPS_LED
GPIO1
GPIO2
GPIO3
GPIO4
GPIO5
GPIO6
GPIO7
AUTOMATION CONNECTIONS
SW_ON_OFF
GSM_RESET
GPS_RESET
R16
13.7k, 1%
R-686
R15
100K, 1%
R-675-G
VCC_IN
VAUX
VCC_IN
USB_ID
USB_VBUS
USB_D+
USB_D-
1
2
3
4
5
6
7
8
9
10
11
12
U8
Supervisor (TPS3808G01)
K-583-M1-G
1 RESET
VDD 6
3 MR
SENSE 5
2 GND
CT 4
GPS_RESET
C19
0.01 uF
C-522-G
50V
AD C1
AD C2
DAC_FILTERED
GPIO1
GPIO2
GPIO3
GPIO4
GPIO5
GPIO6
GPIO7
I2C_SCL
I2C_SDA
P2
CON12
YT-346
On power-up or assertion of MR,
RESET will be pulled low for
approximately 2 seconds.
O N_OFF
SW_ON_OFF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
DAC_FILTERED
SW4
GSR6.34F130QP
S-580-G
2
SW3
GSR6.34F130QP
S-580-G
R26
12.1K
R-391
1
1
1
R25
12.1K
R-391
CELLULAR RESET
Silk Screen Name:
GPS RESET
Silk Screen Name:
ON_OFF
Silk Screen Name:
SW2
GSR6.34F130QP
S-580-G
Header Notes:
SIP Headers can be populated in place of the ZIF sockets to
allow for an extra plug in option. Silk screen addition in
the P18 and P19 footprint should be added to show where
these SIPs will go. The silk screen should look how P3 and
P4 do.
Samtec Headers SLW-125-01-G-S &
SLW-124-01-G-S can be soldered in to allow removable module functionality.
GPIO5
GPIO6
GPIO7
GPS_RESET
GPS_TX
GPS_RX
I2C_SCL
I2C_SDA
USB_ID
USB_VBUS
USB_D+
USB_D-
VAUX
VRTC
AD C1
AD C2
DAC
GPIO1
GPIO2
GPIO3
GPIO4
OMIT
OMIT
P4
1x24 HEADER (0.1" x 0.1")
1x24 ZIF Socket, 0.1" (3M: 224-5809-00-0602)
P19
Allows direct solder connection of GSM865CF, CDMA864CF & UMTS864CF
P7
1x24 HEADER, 0.1" x 0.1" (SLW-124-01-G-S)
XT-432-G
47k
GND
U6 Notes:
D6
R17
GREEN 680
S-213
R-645-G
2
1
P16
RF - SMA Connector (SMA-J-P-H-ST-EM1)
XT-436-G
P6
1x25 HEADER, 0.1" x 0.1" (SLW-125-01-G-S)
XT-431-G
VCC_IN
1
P15
RF - GSC Connector (MM9329-2700RA1)
XT-393-G
1
1
2
ENABLE
3
GSM_RX
4
GSM_DSR
5
GSM_CTS
6
GSM_RING
7
GSM_DCD
8
GSM_TX
9
GSM_DTR
10
GSM_RTS
11
12
TRACE_TX
13
TRACE_RX 14
GPS_LED
15
GSM_LED
16
SERVICE
17
PWRMON
18
O N_OFF
19
GSM_RESET 20
MIC+
21
MIC22
EAR+
23
EAR24
25
P17
RF - MCX Connector (MCX-J-P-H-ST-EM1)
XT-437-G
TRACE_TX
TRACE_RX
GPS_LED
GSM_LED
SERVICE
PWRMON
O N_OFF
GSM_RESET
MIC+
MICEAR+
EAR-
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
U6
Janus Common Footprint Terminal
OMIT
VCC
GND 49
VCC
VAUX 48
ENABLE
VRTC 47
RXD
ADC1 46
DSR
ADC2 45
CTS
DAC 44
RING
GPIO1 43
DCD
GPIO2 42
TXD
GPIO3 41
DTR
GPIO4 40
RTS
GND 39
GND
GPIO5 38
TRACE_TX
GPIO6 37
TRACE_RX
GPIO7 36
GPS_LED
GPS_RESET 35
GSM_LED
GPS_TX 34
SERVICE
GPS_RX 33
PWRMON
I2C_SCL 32
ON_OFF
I2C_SDA 31
RESET
USB_ID 30
MIC+
USB_VBUS 29
MICUSB_D+ 28
EAR+
USB_D- 27
EARGND 26
SW1
8 position DIP switch, SPST, Gold Finish (CT2068)
XT-430
MODE0
MODE1
MODE2
MODE3
MODE4
SERVICE_IN
SWITCHER_ENABLE
ENABLE
N
O
->
->
->
->
->
->
->
->
1
2
3
4
5
6
Vccio1
GPIO_01
GPIO_02
GPIO_03
GPIO_04
GPIO_05
(GCK0)GPIO_06
(GCK1)GPIO_07
(GCK2)GPIO_08
GPIO_09
GPIO_10
GPIO_11
GPIO_12
GPIO_13
GPIO_14
GPIO_15
GPIO_16
GPIO_17
GPIO_18
GPIO_19
U7A
XC2C64A-7QFG48I
K-605-M3-G
I/O BANK1
Vccio2
GPIO_20
GPIO_21
(GTS1)GPIO_22
(GTS0)GPIO_23
(GTS3)GPIO_24
(GTS2)GPIO_25
(GSR)GPIO_26
GPIO_27
GPIO_28
GPIO_29
GPIO_30
GPIO_31
GPIO_32
GPIO_33
GPIO_34
GPIO_35
GPIO_36
GPIO_37
U7B
XC2C64A-7QFG48I
K-605-M3-G
I/O BANK2
U7C
XC2C64A-7QFG48I
K-605-M3-G
P.S.
Vcc 29
Vccaux 3
GND 16
GND 31
GND 41
Vcc
GND
TCK
TDO
TDI
TMS
19
6
7
8
9
10
11
12
13
14
15
17
18
20
24
25
26
27
28
30
42
5
4
2
1
48
47
46
45
44
43
39
38
37
36
35
34
33
32
C27
1 uF
C-562-G
6.3V
VCC3.3
GPS_TX
GPS_RX
GSM_RX
GSM_DSR
GSM_CTS
GSM_RING
GSM_DCD
GSM_TX
GSM_DTR
GSM_RTS
TRACE_TX
TRACE_RX
SERVICE
SERVICE_IN
MODE0
MODE1
MODE2
MODE3
MODE4
C22
1 uF
C-562-G
6.3V
VCC3.3
VCC3.3
C18
1 uF
C-562-G
6.3V
23
40
21
22
MODE0
MODE1
MODE2
MODE3
MODE4
SERVICE ACTIVE
DISABLE DEV. PCB POWER SUPPLY
DISABLE TERMINUS
P5
1x6 HEADER (0.1" x 0.1")
XT-245-G
POS1
POS2
POS3
POS4
POS5
POS6
POS7
POS8
SWITCH DEFINITION:
1
3
D4
SP0505BAJT
S-273
6
D3
SP0505BAJT
S-273
4
4
GSM_LD_RX
GSM_LD_DSR
GSM_LD_CTS
GSM_LD_RING
GSM_LD_DCD
GSM_LD_TX
GSM_LD_DTR
GSM_LD_RTS
TRACE_LD_TX
GPS_LD_TX
TRACE_LD_RX
GPS_LD_RX
nFORCEOFF_LD0
FORCEON_LD0
nFORCEOFF_LD1
FORCEON_LD1
C26
1 uF
C-562-G
6.3V
VBANK1
Added 4/09/10
SERVICE_IN controls SERVICE
C23
1 uF
C-562-G
6.3V
VCC1.8
TCK
TDO
TDI
TMS
JTAG
U7D
XC2C64A-7QFG48I
K-605-M3-G
3
5V_IN
1
OMIT
ENABLE
GSM_RX
GSM_DSR
GSM_CTS
GSM_RING
GSM_DCD
GSM_TX
GSM_DTR
GSM_RTS
P14
RF - GSC Connector (MM9329-2700RA1)
XT-393-G
2
2
6
1x32 ZIF Socket, 0.1" (3M: 232-2601-00-0602)
1
5
P18
3
2
2
3
3
3
VAUX
5
5V_IN
4
4
4
4
6
2
5
2
1 2 3 4 5 6 7 8
2
P3
1x25 HEADER (0.1" x 0.1")
OMIT
APPENDIX — SCHEMATICS continued:
Figure 2: Main Circuit
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
Date: 08/26/13
Not intended for life support applications.
Terminus Plug-In Modules Evaluation Kit User Guide
All Rights Reserved See website for latest revision.
Page 20
VCC3.3
nFORCEOFF_LD1
FORCEON_LD1
TRACE_LD_RX
GPS_LD_RX
TRACE_LD_TX
GPS_LD_TX
VCC3.3
nFORCEOFF_LD0
FORCEON_LD0
GSM_LD_TX
GSM_LD_DTR
GSM_LD_RTS
GSM_LD_RX
GSM_LD_DSR
GSM_LD_CTS
GSM_LD_RING
GSM_LD_DCD
C34
1 uF
C-562-G
6.3V
14
13
15
16
21
20
18
24
23
22
19
17
C29
1 uF
C-562-G
6.3V
14
13
15
16
21
20
18
24
23
22
19
17
CMOS
26
27
4
RS-232
Rev: P04
DB9_TX1
DB9_TX2
DB9_RX1
DB9_RX2
GND C2-
26
27
4
2
GND C2-
C1C2+
VCC C1+
V+
V-
U10B
MAX3238
K-460-G
U10A
MAX3238
K-460-G
8
9
11
C36
1 uF
C-562-G
6.3V
RIN1
RIN2
RIN3
5
6
7
10
12
2
C1C2+
VCC C1+
V+
V-
U9B
MAX3238
K-460-G
3
25
1
28
3
25
1
28
DB9_TX0
DB9_DTR0
DB9_RTS0
DB9_RX0
DB9_DSR0
DB9_CTS0
DB9_RI0
DB9_CD0
U9A
MAX3238
K-460-G
8
9
11
5
6
7
10
12
C31
1 uF
C-562-G
6.3V
RIN1
RIN2
RIN3
DOUT1
DOUT2
DOUT3
DOUT4
DOUT5
C35
1 uF
C-562-G
6.3V
FORCEOFF
FORCEON
INVALID
ROUT1
ROUT1
ROUT2
ROUT3
DIN1
DIN2
DIN3
DIN4
DIN5
CMOS
RS-232
DOUT1
DOUT2
DOUT3
DOUT4
DOUT5
C30
1 uF
C-562-G
6.3V
FORCEOFF
FORCEON
INVALID
ROUT1
ROUT1
ROUT2
ROUT3
DIN1
DIN2
DIN3
DIN4
DIN5
C37
1 uF
C-562-G
6.3V
C33
0.22 uF
C-559-G
16V
C32
1 uF
C-562-G
6.3V
C28
0.22 uF
C-559-G
16V
6
DB9_DSR0
6
7
8
9
P10
DB9-SMT
XT-337-G
6
7
8
9
P9
DB9-SMT
XT-337-G
7
8
DB9_CTS0
DB9_RTS0
9
DB9_RI0
P8
DB9-SMT
XT-337-G
11
10
11
10
11
10
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
DB9_RX2
DB9_TX2
DB9_RX1
DB9_TX1
DB9_CD0
DB9_RX0
DB9_TX0
DB9_DTR0
GPS NMEA PORT
GSM TRACE PORT
AT COMMAND PORT
APPENDIX — SCHEMATICS continued:
Figure 3: RS-232
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
Date: 08/26/13
Not intended for life support applications.
MIC+
EAR+
EARMIC-
VMIC
R20
22K, 5%
R-661G
C40
2.2uF
C-686
6.3V
Q5
MMBT3904
S-257-G
R19
1k, 5%
R-615-G
C49
0.1 uF
C-668-G
16V
C46
0.1 uF
C-668-G
16V
C43
0.1 uF
C-668-G
16V
C39
0.1 uF
C-668-G
16V
Terminus Plug-In Modules Evaluation Kit User Guide
All Rights Reserved See website for latest revision.
Page 21
R21
1k, 5%
R-615-G
C50
39pF
C-656
50V
L4
39uH
L-275-G
C47
39pF
C-656
50V
L3
39uH
L-275-G
C44
39pF
C-656
50V
L2
39uH
L-275-G
C41
39pF
C-656
50V
L1
39uH
L-275-G
C51
1nF
C-696
C48
1nF
C-696
C45
1nF
C-696
C42
1nF
C-696
*MIC-
*EAR-
*EAR+
*MIC+
4
3
2
1
P11
4P4C_RA_JACK
XT-464-G
APPENDIX — SCHEMATICS continued:
Figure 4: Handset Analog Audio
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
Rev: P04
Date: 08/26/13
Not intended for life support applications.
6
5
USB_ID
1
2
3
4
5
3
2
5
6
R23
27, 5%
R-658-G
t
USB_DUSB_D+
USB_VBUS
1
R22
27, 5%
R-658-G
2
1
4
RT1
PTC 200mA (0805L020YR)
S-297-G
P13
1x5 HEADER (0.1" x 0.1")
OMIT
U11
ESD ARRAY (RCLAMP0504F.TCT)
S-574-G
1
2
3
4
C52
10uF, 20%
C-726-G
25V
P12
USB-TYPE B SOCKET (USB-B-S-F-B-TH)
XT-421-G
APPENDIX — SCHEMATICS continued:
Figure 5: USB Port
Terminus Plug-In Modules Evaluation Kit User Guide
Page 22
Rev: P04
Date: 08/26/13
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
All Rights Reserved See website for latest revision.
Not intended for life support applications.
GPS_RESET
MODE0
ON_OFF
GSM_RESET
SERVICE_IN
ENABLE
2
6
4
2
6
4
2
6
4
VCC
1A
2A
VCC
1A
2A
GND
1Y
2Y
VCC
1A
2A
U14
SN74LVC2G07
OMIT
GND
1Y
2Y
U13
SN74LVC2G07
OMIT
GND
1Y
2Y
U12
SN74LVC2G07
OMIT
5
1
3
5
1
3
5
1
3
PA4
PA5
PA2
PA3
PA0
PA1
C58
0.1 uF
OMIT
16V
VCC_5PC
C57
0.1 uF
OMIT
16V
VCC_5PC
C56
0.1 uF
OMIT
16V
VCC_5PC
Terminus Plug-In Modules Evaluation Kit User Guide
Page 23
All Rights Reserved See website for latest revision.
Rev: P04
C63
0.1 uF
OMIT
16V
VAUX
GPIO6
GPIO7
C62
0.1 uF
OMIT
16V
VAUX
GPIO4
GPIO5
C61
0.1 uF
OMIT
16V
VAUX
GPIO2
GPIO3
5
1
3
5
1
3
5
1
3
5
VAUX
C60
0.1 uF
OMIT
16V
1
3
5
1
3
GSM_LED
GPIO1
C59
0.1 uF
OMIT
16V
VAUX
PWRMON
GPS_LED
GND
1Y
2Y
GND
1Y
2Y
GND
1Y
2Y
GND
1Y
2Y
VCC
1A
2A
GND
1Y
2Y
U19
SN74LVC2G07
OMIT
VCC
1A
2A
U18
SN74LVC2G07
OMIT
VCC
1A
2A
U17
SN74LVC2G07
OMIT
VCC
1A
2A
U16
SN74LVC2G07
OMIT
VCC
1A
2A
U15
SN74LVC2G07
OMIT
2
6
4
2
6
4
2
6
4
2
6
4
2
6
4
PC5
PC6
PC3
PC4
PC1
PC2
PB2
PC0
PB0
PB1
R35
10K, 5%
OMIT
R33
10K, 5%
OMIT
R31
10K, 5%
OMIT
R29
10K, 5%
OMIT
R27
10K, 5%
OMIT
R36
10K, 5%
OMIT
VCC_5PC
R34
10K, 5%
OMIT
VCC_5PC
R32
10K, 5%
OMIT
VCC_5PC
R30
10K, 5%
OMIT
VCC_5PC
R28
10K, 5%
OMIT
VCC_5PC
PA0
PA2
PA4
PC0
PC2
PC4
PC6
PB0
PB2
50
48
46
44
42
40
38
36
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
49
47
45
43
41
39
37
35
33
31
29
27
25
23
21
19
17
15
13
11
9
7
5
3
1
PA1
PA3
PA5
PB1
PC1
PC3
PC5
VCC_5PC
P22
HEADER 25X2 (HTST-125-01-L-D)
OMIT
APPENDIX — SCHEMATICS continued:
Figure 6: Factory Automation (not populated)
© Copyright 2013 Janus Remote Communications Specifications subject to change without notice
Date: 08/26/13
Not intended for life support applications.
Terminus Plug-In Modules
Evaluation Kit User Guide
Revision Revision Date
Note
A00
05/15/10
A01
06/28/10
P00
01/17/12
P01
04/05/12
P02
11/15/12
P03
07/10/13
P04
08/26/13
Preliminary Release
Updates to Eval Board Descriptions & Specs
Updated Power Supply Interfaces, Schematic, DIP
Switches. Moved to Preliminary Status
Added HSPA910CF Description and Specs
Added EVDO910CF Description and Specs
New Board Photo Update
Updated Page 14 information - P15 should be P14 & Legal Statement
Division of The Connor-Winfield Corporation
2111 Comprehensive Drive • Aurora, Illinois 60505
630.499.2121 • Fax: 630.851.5040
www.janus-rc.com
Janus Remote Communications Europe Bay 143
Shannon Industrial Estate
Shannon, Co. Clare, Ireland
Phone: +353 61 475 666