Download User`s Manual

BPU-124V2-S
SS
BPU
U‐124V2‐SS
Hard
dware Information: Rear V
View BPU
U‐124V2‐SS
7
10
8
11
9
12
13
14
15
18
Pictture C‐1 16 17
Picture
P
B
Picture C‐2
Securi ty Lock B7: 155pin SATA powerr connector The Lockaable Design keep s the HDDs stayying inside the u
unit and preventts HDDs B8 & B
B9: 40mm Cooli ng Fan being takken out while thhey are running . B10, B
B12, B14, B16: Primary Chann el (black)  fo r SATA or SAS HDD H
data p
ports B11, B
B13, B15, B17: Secondary Chan
nnel (yellow)   for SAS HDD data d
ports & advanced use
ers. *Note for Conn
nections: A
A.
For SATA HD
DDs, they are su pported by Prim
mary ports (B10,, B12, B14, a nd B16) only. B
B.




For SAS HDDss, they are supportted by both Primary & Secondary channels. C
C.
Accesso
ories: Dual channel SAS control card o
or two systems (PC
C) are needed if bo
oth primary & s econdary ports need to be use d simultaneouslly. HDD LED Switch Indication desccription: B18: H
a) Wh
hen it is set to “X” Position, th
he front LED do
oes NOT blink while w
HDD i s being accesse d. pin up when th
he system powe
er is In thi s case, the harrd drives will sp
turned
d on. b) Wh
hen it is set to “O” “
position, fr ont LED blinkin g in blue/red while w
the HD
DD is being acce
essed. In thi s case, the HDD
D will not spin up until the SA
ATA initial signaal is receivved. 1 maanual 2 keeys 4 SA
ATA cables Neceessary screws iStarUSSAcare: We will hhelp you navigate our website to find the information that you needd. Go to www.istarrusa.com, and click on live chat bubble above thhe Search Bar. Our techhnicians are standing by to take yourr questions. Visit http://istaarusa.com/supportt/ , and you will reeceive a technical ssupport ticket to hhelp track your req
quests from the beeginning to the end
d. Or you can coontact us @ 888‐9989‐1189. (c) Th e default settingg for B18 (HDD LED Switch) is t o “O” position (HDD LED Enable). HDD
D Installation
n: A.
FFor 2.5” SATA HD
DD (SSD): P
Put HDD onto th e tray as shown on Picture C‐1 and use the p
provided screws to secure HDD on the tray one by one. B.
diation Norm
FCC and CE Rad
FCC
This equipment haas been tested and found to com
mply with limits for Class B digital device pursuant to Part 15 of Fe
ederal Communications Commiss
sion (FCC)
rules.
CE
This equipment haas been tested and found to com
mply with the limits of the Europea
an Council Directive on the appro
oximation of the law of the memb
ber states
relating to electrom
magnetic compatibility (89/336/E
EEC) according to EN 55022 Classs B.
FCC and CE Com
mpliance Statement
These limits are ddesigned to provide reasonable pprotection against frequency interrference in residential installation
n. This equipment generates uses
s and can
radiate radio frequuency energy, and if not installedd or used in accordance with the instructions may cause harmful iinterference to radio communication. However,
there is no guaranntee that interference will not occcur in television reception, which can be determined by turning the
e equipment off and on. The user is encouraged
to try and correct the interference by one or more of the following measures: Reorrient or relocate the receiving anttenna, Increase the separation be
etween the
equipment and thhe receiver, connect the equipme nt into an outlet on a circuit differrent from that to which the receivver is connected to.
CAUTION!
mmunications Commission warns the user that changes or modificcations to the unit not expressly a
approved by the party responsible
e for the
The Federal Com
compliance couldd void the user’s authority to operrate the equipment.
FFor 2.5” SAS HDD
D or HDD’s thickkness is more th an 10.5mm: Loo
ose t he cover‐mountting screw and rremove the top cover. Mount th
he SSAS HDD or the tthick HDD on th e open tray. ( Note: after SAS HDD installed, do not put on th
he top cover (se
ee P
Picture C‐2.) putt the top cover i n a safe place, iin case you need
d it n
next time.)
BPU‐124V2‐SS
B
BPU‐124V2‐SS