Transcript
1 - Microphone 2 - Function Button 3 - Volume Up ( +) 4 - LED Indicator 5 - Play Back Headset Functions 1. Charging Your Headset : To prolong the battery life, it is recommended to fully charge your headset. The red LED indicator will light up showing that the unit is being charged. When charging is complete, the red LED will turn off. When the battery is running low, the LED will flash red. 6 - Volume Down ( -) 7 - Forward 8 - Charging Port 9 - Strap Holder (Strap not included) 10 - 3.5mm Audio Output 3. Power ON your Headset : Press and hold the Function button for 4 seconds until you hear a short beep and the indicator light flashes blue 3 times. Now the headset will enter into STANDBY MODE. If no paired phone is in range or no phone has been paired, the “N550” will enter Standby mode. 4. Power OFF your Headset : Press and hold the Function button 4 seconds until you hear a short beep and the indicator light flashes red 3 times. 2. Pairing Your Headset : 1. First turn the phone OFF and then back ON again to refresh its memory. 2. Bring the phone to about 30cm from NoiseHush “N550” headset. 3. Find the Bluetooth menu in your phone. Turn Bluetooth ON. (See your phone’s user guide) 4. With the NoiseHush headset OFF, press and hold the Function button for about 8 seconds until the LED flashes blue to red. 5. Your headset is now ready to be discovered by your Bluetooth phone. 5. Answering/Ending a Call : Press the Function button once when there is an incoming call to Answer. Press the Function button once again to end the call. 6. Perform a Bluetooth device discovery on your phone to add a new device. It takes a few seconds to discover other Bluetooth devices around you. 7. When Bluetooth devices are found, the phone will display NoiseHush “N550”. Scroll to it and press OK to confirm that you want to pair with it. 8. Enter the Passkey "0000" when your phone prompts you. The phone will now pair with the headset. 9. If your Bluetooth phone menu supports it "set as authorized "or" add to trusted devices". 10. Again, select the NoiseHush "N550” or press the Function button to connect with the phone. 7. Redialing Last Number : Press and hold Function button for 2 seconds until you hear the beep, then release immediately. 11. If the pairing is not successful, the Headset will return to the standby mode after awhile, please repeat the pairing process to try the pairing again. 12. Refer to your phone’s user manual for any additional steps. 9. Music Features : 1. Play/Pause Function : Once the music is selected from your phone (See your phone’s user guide), press the Function button once for music to pause and press again to play. **Blue LED indicator blinks once every 4 seconds when it’s paired with your phone and once every 8 seconds when it is not paired. 2. To Forward (>>) arrow down Press the Function button to skip and play the next song. 6. To Activate Voice Dialing : Rapidly press the Function button twice, then you will hear two beeps. Say the voice tag as soon as you hear the beep. Make sure your phone supports the voice dialing function, and you have prerecorded the voice tag into your phone. (See your phone’s user guide) 8. To Adjust the Volume : Click the Volume Up or Volume Down button during a call. Adjust to the desired level. The volume level you set will be remembered by the NoiseHush “N550” and used on the next call. * To use these functions, your phone/device must support the Bluetooth Handsfree Profile. 3. To Play Back (<<) arrow up Press the Function button to return to the last song. Note: Make sure your phone supports AVRCP Bluetooth Profile for remote-control functions and A2DP for Music capability. Note: To conserve battery, NoiseHush “N550” will automatically turn off if it’s not paired with your phone. Contact Us For additional help or to purchase accessories such as AC/DC, please visit us at www.noisehush.com. 10. Disconnecting : Please turn off paired “N550” headset or disconnect the headset from the Bluetooth menu of your phone.