Download FIPSOC User Manual

Transcript
SIDSA
SW Breakpoints Interrupt Vector (h0000 after Reset)
Address
$B5,$B4
Name
VDBG
$B4
$B5
Byte
VDBGL
VDBGH
Description
DEBUG Interrupt Vector.
Pseudovector
used
when
extended interrupt mode is
enabled (INTM = 1), external
interrupt and DBGint are
enabled and a memory
location is debbuged (a
breakpoint is reached).
DBG Interrupt Vector Low Byte
DBG Interrupt Vector High Byte
Semiconductor Design Solutions
Extended Interrupt Mask Register 0 (h00 after Reset)
Address
$C0
Name
EIMR0
EIMR0.7
EIMR0.6
EIMR0.5
Programmable Hardware vector 3 (h0000 after
Reset)
Address
$B7,$B6
Name
VHW3
$B6
$B7
Byte
VHW3L
VHW3H
Description
HW3
Interrupt
Vector.
Pseudovector
used
when
extended interrupt mode is
enabled (INTM = 1), external
interrupt and HW3int are
enabled and an Interrupt from
the Plblock happens through
HW3INT input.
HW3 Interrupt Vector Low Byte
HW3 Interrupt Vector High Byte
Programmable Hardware vector 4 (h0000 after
Reset)
Address
$BD,$BC
Name
VHW4
$BC
$BD
Byte
VHW4L
VHW4H
EIMR0.4
EIMR0.3
EIMR0.2
EIMR0.1
EIMR0.0
$BF,$BE
Name
VANA
Byte
Address
$C1
Name
EIMR1
Description
HW4
Interrupt
Vector.
Pseudovector
used
when
extended interrupt mode is
enabled, external interrupt
and HW4int are enabled and
an Interrupt from the PLblock
happens through HW4INT
input.
HW4 Interrupt Vector Low Byte
HW4 Interrupt Vector High Byte
$BE
VANAL
$BF
VANAH
Description
Analog
Interrupt
Vector.
Pseudovector
used
when
extended interrupt mode is
enabled (INTM = 1), external
interrupt and analog inerrupt
enabled
and
an
A-D
conversion is finished.
Analog Interrupt Vector Low
Byte
Analog Interrupt Vector High
Byte
Description
Extended Interrupt Mask
Register
for
External
Interrupt 0. A 0 means that
the corresponding source is
masked.
Enable or Disable PLL interrupt
through IX0
HW1 / COM interrupt through
External Int 0 (if 1, HW1 is
selected)
Enable or Disable CLK interrupt
through External Int 0
Enable or Disable HW2 interrupt
through External Int 0
Enable or Disable DBG interrupt
through External Int 0
Enable or Disable HW3 interrupt
through External Int 0
Enable or Disable HW4 interrupt
through External Int 0
Enable or Disable ANA interrupt
through External Int 0
Extended Interrupt Mask Register 1 (h00 after Reset)
Bit
EIMR1.7
EIMR1.6
EIMR1.5
EIMR1.4
EIMR1.3
End of Conversion Interrupt Vector (h0000 after
Reset)
Address
Bit
EIMR1.2
EIMR1.1
EIMR1.0
Description
Extended Interrupt Mask
Register
for
External
Interrupt 1. A 0 means that
the corresponding source is
masked
Enable or Disable PLL interrupt
through External Int 1
Enable or Disable HW1 interrupt
through External Int 1
Enable or Disable CLK interrupt
through External Int 1
Enable or Disable HW2 interrupt
through External Int 1
Enable or Disable DBG interrupt
through External Int 1
Enable or Disable HW3 interrupt
through External Int 1
Enable or Disable HW4 interrupt
through External Int 1
Enable or Disable ANA interrupt
through External Int 1
Polarity Register 0 (h00 after Reset)
Address
$C2
Name
SGNI0
Byte
Description
Inverting extended external
Interrupts through Ext. Int. 0
For each bit of this register, if
1, inverts the corresponding
interrupt input (high level or
rising edge interrupts).
Polarity Register 1 (h00 after Reset)
Address
$C3
Chapter 6. External Interrupts Controller
Name
SGNI1
Byte
Description
Inverting extended external
Interrupts through Ext. Int. 1
For each bit of this register, if
1, inverts the corresponding
interrupt input (high level or
rising edge interrupts).
5