Download User`s Manual
Transcript
owner's Manual REVO LINE ARRAY SPEAKER ENCLOSURES PASSIVE MODELS SEIKAKU TECHNICAL GROUP LIMITED NO. 1, Lane 17, Sec. 2, Han Shi West Road, Taichung 40151, Taiwan www.altoproaudio.com Tel: 886-4-22313737 email:[email protected] Fax: 886-4-22346757 All rights reserved to ALTO. All features and content might be changed without prior notice. Any photocopy, translation, or reproduction of part of this manual without written permission is forbidden. Copyright c 2008 Seikaku Group www.altoproaudio.com Version 1.1 JUL. 2008 English 14. WARRANTY IMPORTANT SAFETY INSTRUCTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK PLEASE DO NOT REMOVE THE COVER OR THE BACK PANEL OF THIS EQUIPMENT. THERE ARE NO PARTS NEEDED BY USER INSIDE THE EQUIPMENT. FOR SERVICE, PLEASE CONTACT QUALIFIED SERVICE CENTERS. This symbol, wherever used, alerts you to the presence of un-insulated and dangerous voltages within the product enclosure. These are voltages that may be sufficient to constitute the risk of electric shock or death. This symbol, wherever used, alerts you to important operating and maintenance instructions. Please read. Protective Ground Terminal AC mains (Alternating Current) Hazardous Live Terminal ON: Denotes the product is turned on. OFF: Denotes the product is turned off. CAUTION Describes precautions that should be observed to prevent damage to the product. 1. Read this Manual carefully before operation. 2. Keep this Manual in a safe place. 3. Be aware of all warnings reported with this symbol. 4. Keep this Equipment away from water and moisture. 5. Clean it only with dry cloth. Do not use solvent or other chemicals. 6. Do not damp or cover any cooling opening. Install the equipment only in accordance with the Manufacturer's instructions. 7. Power Cords are designed for your safety. Do not remove Ground connections! If the plug does not fit your AC outlet, seek advice from a qualified electrician. Protect the power cord and plug from any physical stress to avoid risk of electric shock. Do not place heavy objects on the power cord. This could cause electric shock or fire. 8. Unplug this equipment when unused for long periods of time or during a storm. 9. Refer all service to qualified service personnel only. Do not perform any servicing other than those instructions contained within the User's Manual. 10. To prevent fire and damage to the product, use only the recommended fuse type as indicated in this manual. Do not short-circuit the fuse holder. Before replacing the fuse, make sure that the product is OFF and disconnected from the AC outlet. WARNING To reduce the risk of electric shock and fire, do not expose this equipment to moisture or rain. 1. WARRANTY REGISTRATION CARD To obtain Warranty Service, the buyer should first fill out and return the enclosed Warranty Registration Card within 10 days of the Purchase Date. All the information presented in this Warranty Registration Card gives the manufacturer a better understanding of the sales status, so as to provide amore effective and efficient after-sales warranty Dispose of this product should not be placed in municipal waste and should be separate collection. 11. Move this Equipment only with a cart, stand, tripod, or bracket, specified by the manufacturer, or sold with the Equipment. When a cart is used, use caution when moving the cart / equipment combination to avoid possible injury from tip-over. 12. Permanent hearing loss may be caused by exposure to \ extremely high noise levels. The US. Government's Occupational Safety and Health Administration (OSHA) has specified the permissible exposure to noise level. These are shown in the following chart: HOURS X DAY SPL EXAMPLE 8 6 4 3 2 1,5 1 0,5 0,25 or less 90 92 95 97 100 102 105 110 115 Small gig train Subway train High level desktop monitors Classic music concert service. Please fill out all the information carefully and genuinely, miswriting or absence of this card will void your warranty service. 2. RETURN NOTICE 2.1 In case of return for any warranty service, please make sure that the product is well packed in its original shipping carton, and it can protect your unit from any other extra damage. 2.2 Please provide a copy of your sales receipt or other proof of purchase with the returned machine, and give detail information about your return address and contact telephone number. 2.3 A brief description of the defect will be appreciated. 2.4 Please prepay all the costs involved in the return shipping, handling and insurance. 3. TERMS AND CONDITIONS 3.1 LTO warrants that this product will be free from any defects in materials and/or workmanship for a period of 1 year from the purchase date if you have completed the Warranty Registration Card in time. 3.2 The warranty service is only available to the original consumer, who purchased this product directly from the retail dealer, and it can not be transferred. 3.3 During the warranty service, LTO may repair or replace this product at its own option at no charge to you for parts or for labor in accordance with the right side of this limited warranty. 3.4 This warranty does not apply to the damages to this product that occurred as the following conditions: Instead of operating in accordance with the user's manual thoroughly, any abuse or misuse of this product. Normal tear and wear. Rock concert According to OSHA, an exposure to high SPL in excess of these limits may result in the loss of hear. To avoid the potential damage of heat, it is recommended that Personnel exposed to equipment capable of generating high SPL use hearing protection while such equipment is under operation. The apparatus shall be connected to a mains socket outlet with a protective earthing connection. The product has been altered or modified in any way. Damage which may have been caused either directly or indirectly by another product / force / etc. Abnormal service or repairing by anyone other than the qualified personnel or technician. And in such cases, all the expenses will be charged to the buyer. 3.5 In no event shall LTO be liable for any incidental or consequential damages. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you. 3.6 This warranty gives you the specific rights, and these rights are compatible with the state laws, you may also have other statutory rights that may vary from state to state. The mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. 17 13. CONTROL ELEMENTS: D4 Amplifier IN THIS MANUAL: Front Panel 1. INTRODUCTION TO THE REVO SAT208P ..........................................................................2 2. REVO SAT208P TECHNICAL SPECIFICATION ....................................................................3 3. INTRODUCTION TO THE REVO SUB118P..........................................................................4 D4 SIG CLIP PROT 20 18 SIG CLIP PROT 18 22 16 26 CH1 30 (dB) 16 24 26 28 6 CH2 20 18 22 12 28 6 20 16 24 12 SIG CLIP PROT 24 26 28 6 CH3 30 (dB) 18 22 12 750W SIG CLIP PROT 30 (dB) 20 5. LAYOUT OF CONNECTOR PANEL REVO SAT 208P.............................................................6 22 16 24 26 12 28 6 CH4 30 (dB) 6. HIGH FREQUENCY CONFIGURATOR (HFC) ......................................................................7 7. REVO MAXIMUM ARRAY SIZE .......................................................................................8 3 18 20 SIG CLIP PROT 18 22 16 24 26 12 28 6 CH1 30 (dB) 20 SIG CLIP PROT 18 22 16 26 28 6 CH2 30 (dB) 20 16 24 12 1 4 2 SIG CLIP PROT 18 22 26 28 6 CH3 6 8. DEPLOYING THE SYSTEM IN SUSPENSION & COMPRESSION ..........................................9 SIG CLIP PROT 24 12 4. REVO SUB118P TECHNICAL SPECIFICATION ...................................................................5 4 30 (dB) 20 9. SPEAKER MANAGEMENT: MAXIDRIVE3.4+ ....................................................................10 22 16 24 26 12 10. HOOK-UP: 12XSAT208P+8XSUB118P CONFIGURATION...............................................11 28 6 CH4 30 (dB) 10. HOOK-UP: 8XSAT208P+4XSUB118P CONFIGURATION.................................................12 5 10. HOOK-UP: 4XSAT208P+2XSUB118P CONFIGURATION.................................................13 1 Power Switch & Indicator LED 4 Protection LED 2 Signal LED 5 Gain Controls 3 Clip LED 6 Cooling Vents 11. REVO LINE ARRAY HARDWARE PARTS .......................................................................14 12. CONTROL ELEMENTS: MAXIDRIVE3.4+ PROCESSOR ...................................................15 13. CONTROL ELEMENTS: D4 AMPLIFIER..........................................................................16 14. WARRANTY .............................................................................................................17 Rear Panel PUSH PUSH CH1 LOCK CH1/CH2 CH2 PARALLEL STEREO BRIDGED CH1 BRIDGED MONO LOCK CH2 MODEL 1+ 1 CH2 2+ 2 BRIDGED LF 30HZ FILTER SERIAL 1+ 2+ OFF ON BRIDGED OUTPUT INPUT PUSH PUSH CH3 MADE IN CHINA DESIGNED IN ITALY LOCK CH3/CH4 CH4 PARALLEL STEREO BRIDGED CH3 BRIDGED MONO CH3 LOCK 1+ 1 CH4 1+ 1 8 2+ 2 BRIDGED 1+ 2+ 220 -240V ~50/60Hz Rated Power Consumption 3000W OFF ON INPUT 13 OUTPUT 9 12 14 11 10 7 Circuit Breaker 11 Binding Post Outputs 8 IEC Socket for AC Power Cable 12 Low Frequency Filter 9 Combo Balanced Input Connectors 13 Output Mode Selector 10 Speakon Outputs 7 BREAKER CH4 CH4 LF 30HZ FILTER BRIDGED 16 CH1 1+ 1 CH2 14 Cooling Fan 1 12. CONTROL ELEMENTS: MAXIDRIVE3.4+ PROCESSOR 1. INTRODUCTION TO THE REVO SAT208P Front Panel 5 2 PREV 12 8 NEXT ENTER CLIP PRESET 6 DELAY EDIT MODE CLIP CLIP CLIP CLIP CLIP CLIP LIMIT LIMIT LIMIT LIMIT LIMIT LIMIT 6 12 ESC 18 24 UTILITY A B INPUT LEVEL 6 6 6 6 6 12 OUTPUT LEVEL 12 OUTPUT LEVEL 12 OUTPUT LEVEL 12 OUTPUT LEVEL 12 OUTPUT LEVEL 12 OUTPUT LEVEL 24 1 24 2 24 3 24 4 24 5 24 6 MUTE MUTE MUTE MUTE MUTE MAXIDRIVE3.4+ 3-WAY STEREO DIGITAL CROSSOVER MUTE CARD 1 REVO is a compact two-way passive, line array system, intended for use in arrays with fixed curvature, up to six cabinets of SAT208P. The REVO is a versatile loudspeaker system for medium & large Indoor venues. it is suitable in small and medium outdoor scale application, or as a delay tower for large scale sound reinforcement system. The REVO was born for make a line-array with fixed curvature, with 100 horizontal & 40 Vertical coverage pattern, aim to simulate a coherent waveguide with six enclosure. A main frame hardware defines the tilting of the complete array system between +20 /-25 . The SAT208P includes a dual angle pole socket, plus the accessory for a suspension options. It is easy to use integral rigging hardware, and give the possibility to assemble a max of 6 x SAT208P in suspension or 1x SUB118P plus 4 x SAT208P in the same way as a single source. A high frequency selector is included in the passive crossover for giving you more flexibility to define an amplitude shading of the REVO. The 0dB position is normally used to coverage the near field audience. The +3dB position is normally used to coverage the far field audience. The SAT208P is normally used in Passive mode, and no restriction exist for use in Bi-Amp mode with the way of Passive Active selector. The SAT208P is equipped with two custom high power 8" Mid-Bass of the 2" sandwich copper voice coil on fiberglass former, and two1"high frequency drivers with 1.4" voice coil of titanium diaphragm are used on double proprietary waveguide horn. 3 7 4 6 9 10 11 1 MODE Button 2 LEDs 3 Display DIAL Knob 5 PREV/NEXT Button 6 Navigation Cursor Keys 8 ENTER Key 9 ESC key 4 7 Memory Card Slot 10 Input Level LEDs 12 Output Level LEDs 11 Mute Switches Rear Panel AC INPUT Apparaten skall anslutas till 14W jordat uttag nar den ansluts 95-240V 50/60Hz FUSE: 95-120V T500mAL till ett natverk 210-240V T315mAL PUSH PUSH DESIGNED IN ITALY MADE IN CHINA PUSH OUTPUTS NEW PWR NEW ON A102 OFF 13 14 TIDE NEW 3 2 DIGITAL IN 15 2 RS485 OUT 16 NEW TIDE TIDE 2 3 1 PUSH TIDE 1 RS485 IN RS232 17 18 6 5 3 4 2 19 13 AC Inlet and Fuse Holder 14 Power Switch 15 Digital In 16 Rs485 OUT 17 Rs485 IN 18 RS 232 19 OUTPUTS 20 INPUTS 1 1 2 1 3 3 INPUT B INPUT A 20 Dimension Drawings for REVO SAT208P 620 271.5 7.5 423.5 REVO1 SAT 208P 0dB POWER HANDLING: 400 W AES 1600 W PEAK IMPEDANCE: 8 Ohm BI-AMP PIN1+1-: LO-MID PIN2+2-: HIGH HIGH +3dB INPUT BI-AMP LO-MID: 400 W HIGH: 75 W IMPEDANCE: LO-MID: 8 Ohm HIGH: 8 Ohm THRU PASSIVE BI-AMP PASSIVE PIN1+1-: INPUT PIN2+2-: N/C MODEL SERIAL Designed in Italy 2 15 2. REVO SAT208P TECHNICAL SPECIFICATION 11. REVO LINE ARRAY HARDWARE PARTS 23 700 1 2 3 4 5 6 7 8 9 10 11 12 13 14 682 20.1 17.5 14.9 12.1 Model No. Configuration Operating Frequency Range Frequency Response Maximum Peak SPL Power Rating (AES Standard) REVO SAT 208P Two-way, Passive or Bi-Amp, with a total of four speakers device 65 Hz/20 kHz (-10 dB) 77 Hz/18 kHz (+/-3 dB) 126 dB SPL (calculated) 400 W/800 W/1600W passive mode Bi-amp Low 400 W/800 W Bi-amp High 75 W/150 W 100 nominal, single unit 7.5 variable with array configuration 2 x 8" Mid-Bass, 2" high-power voice coil, ceramic magnet, Weather resistant cone. Impedance 16 ohm 2x1, 4" Titanium diaphragm, neodymium magnet,1"exit Impedance 16 ohm 95 dB SPL (passive mode) Passive or Bi-Amp with externally selector High frequency externally level selector, Used for far field (+3 dB) or Near field(0dB) 97 dB SPL, passive version Bi-Amp Low 97 dB (device parallel) Bi-Amp High 107 dB (2 device parallel) Passive 8 ohm Bi-Amp Low 8 ohm (2 device parallel) Bi-Amp High 8 ohm (2 device parallel) Integrated hardware for suspension in Line Array, dual pole socket, two handle 18mm calibrated plywood, black finish, Perforated metal grille, black finish Two Speakon N-L 4 type, Passive, Input 1+/1- Output 1+/1Bi-Amp, Low 1+/1- High 2+/ 2271.5 mm x 620 mm x 423.5 mm (10.7" x 24.4" x 16.7") 21.8 kg (48 lbs) Coverage Horizontal Coverage Vertical Transducers Low-Mid 0.8 2.1 5 7.8 10.6 13.4 16.1 18.7 21.3 23.7 Transducers High Crossover modes System Sensitivity (1w@1mt) Nominal Impedance REVO FB-1 Suspension / Mounting Enclosure Input Connectors REVO SH Dimension (H x W x D) Net Weight (Kg/lbs) 1. "Frequency Response" is measured in half-space condition. 2. AES filtered pink noise with 6 dB crest factor for 2 hours. REVO SAT-HD-R REVO SUB-HD-L REVO SAT208P BLOCK DIAGRAM LOW FREQ HIGH FREQ REVO SAT-HD-L 14 REVO SUB-HD-R LOW FREQ HIGH FREQ 3 HOOK 3. INTRODUCTION TO THE REVO SUB118P 10. HOOK-UP: 4xSAT208P+2xSUB118P CONFIGURATION SUBR1 Hardware for two REVO SAT208P 2 REVO SAT-HD-L per array 2 REVO SAT-HD-R per array Deploy in suspension or compression UP The SUB118P is a vented subwoofer equipped with a single custom high power 18" Subwoofer with 4" high-power sandwich copper voice coil on fiberglass former, double spider, ceramic magnet, and weather resistant cone. The enclosure is made with a 18mm multi-layer plywood, finished with anti-scratch black paint, with a strong perforated metal grille, two metal handles, one pole socket for satellite and four wheels. Dimension Drawings for REVO SUB118P 792.5 700 620 REVO1 SUB 118P POWER HANDLING: 750 W AES 1500 W PEAK IMPEDANCE: 8 Ohm MODEL SERIAL Designed in Italy DIRECT INPUT PASSIVE THRU/OUTPUT 620 4 13 12 SUBL1 SUBL2 Subwoofer REVO SUB118P REVO SAT208P SATL4 SATL3 SATL2 SATL1 LEFT ARRAY A102 30 (dB) CH1 CH2 6 18 26 24 28 30 (dB) 22 20 16 12 SIG CLIP PROT 26 24 28 22 20 18 SIG CLIP PROT 6 CH3 6 16 12 18 20 26 24 28 30 (dB) 22 SIG CLIP PROT CH4 6 16 12 18 20 26 24 28 30 (dB) 22 SIG CLIP PROT SBL1 SUB 1 14W Apparaten skall anslutas till SBR1 SUB 3 OFF ON PWR 3 1 TIDE DIGITAL IN 2 NEW PUSH jordat uttag nar den ansluts 95-240V 50/60Hz FUSE: 95-120V T500mAL till ett natverk 210-240V T315mAL AC INPUT SBL2 SUB 2 RS485 OUT 3 1 TIDE RS485 IN 2 NEW SR5 SR4 SL5 SL4 SR3 SR2 SL3 SL2 BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH CH2 CH4 CH2 INPUT CH4 CH2 CH4 INPUT CH2 INPUT CH4 INPUT BRIDGED CH3 INPUT BRIDGED CH1 BRIDGED CH3 BRIDGED CH1 INPUT PARALLEL CH3 INPUT PARALLEL CH1 PARALLEL CH3 INPUT PARALLEL CH1 PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH NEXT RS232 DESIGNED IN ITALY MADE IN CHINA REVO1-CNP PUSH SBR2 SUB 4 CARD PREV ALTO Power Amplifiers: 4 D4 ALTO Connetor pack REVO -CNP 16 12 PRESET DELAY UTILITY EDIT SUBL1 SUBL2 SUBR1 SUBR2 MODE A 3 1 TIDE 5 SR5 2 4 3 1 OUTPUTS 3 SL4 2 NEW CH2 CH4 CH2 CH4 CH2 CH4 CH2 CH4 BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO CH1 CH3 CH1 CH3 CH1 CH3 CH1 CH3 OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT CLIP 3 1 TIDE SL5 2 NEW 4 2 CLIP 2 1 3 1 TIDE PUSH NEW CLIP 1 TIDE 1 3 2 INPUT A 3 1 NEW INPUT B 2 NEW TIDE 3 PUSH 2 NEW LINK 3 750W 4 D4 3-WAY STEREO DIGITAL CROSSOVER MAXIDRIVE3.4+ MUTE TIDE 6 OUTPUT LEVEL PUSH 24 12 6 LIMIT MUTE IN 3 5 OUTPUT LEVEL SL1 24 12 6 LIMIT MUTE OUTPUT LEVEL LINK 2 24 12 6 LIMIT MUTE SR1 3 OUTPUT LEVEL SR3 SL3 SR2 SL2 6 SR4 1 TIDE 3 NEW IN 2 PUSH 2 NEW 6 12 24 SL1 MUTE TIDE LINK 1 2 CLIP OUTPUT LEVEL LIMIT 24 12 6 MUTE CLIP 1 LIMIT OUTPUT LEVEL 6 24 12 CLIP LIMIT B 6 24 18 12 CLIP INPUT LEVEL PUSH IN 1 SR1 ESC ENTER SBR2 SBR1 SBL2 SBL1 SATR4 SATR3 SATR2 SATR1 SATL4 SATL3 SATL2 SATL1 ALTO Processor MAXIDRIVE3.4+ REVO SAT208P SATR4 SATR3 SATR2 SATR1 RIGHT ARRAY SUBR1 SUBR2 Subwoofer REVO SUB118P Hardware for four REVO SAT208P 4 REVO SAT-HD-L per array 4 REVO SAT-HD-R per array Deploy in suspension or compression Hardware for each REVO SUB118P 1 REVO SUB-HD-L 1 REVO SUB-HD-R REVO1 SERIES STEREO LINE ARRAY WITH SUBS (8 STA208P+4 SUB118P) HOOK 10. HOOK-UP:8xSAT208P+4xSUB118P CONFIGURATION 4. REVO SUB118P TECHNICAL SPECIFICATION UP Model No. Configuration Operating Frequency Range Frequency Response Maximum Peak SPL Power Rating (AES Standard) Transducers Low Crossover modes System Sensitivity (1w@1mt) Nominal Impedance Suspension / Mounting Enclosure Input Connectors Dimension (H x W x D) Net Weight (Kg/lbs) REVO SUB 118P DIRECT INPUT REVO SUB 118P Vented Subwoofer, Passive or Direct 37 Hz~200 Hz (-10 dB) 43 Hz~200 Hz (+/- 3 dB) 129 dB SPL (calculated) 750 W/1500 W 18" Subwoofer, 4" high-power voice coil Ceramic magnet, weather resistant cone. Passive, Active with externally selector in direct connection 97 dB SPL, passive version 8 ohm, nominal Single 36 mm pole socket, four integrated point For line array suspension, two handle, four optional wheel 18 mm calibrated plywood, black finish, perforated metal grille Two SPK N-L 4 type, Passive, Input 1+/1- Output 1+/1Direct 1+/1- ( 2 SPK parallel ) with externally selector 620 mm x 620 mm x 700 mm (24.4" x 24.4" x 27.5") 51.8 Kg (113.4 lbs) 1. "Frequency Response" is measured in half-space condition. 2. AES filtered pink noise with 6 dB crest factor for 2 hours. Rear panel REVO SUB 118P BLOCK DIAGRAM POWER HANDLING: 750 W AES 1500 W PEAK IMPEDANCE: 8 Ohm SERIAL MODEL Designed in Italy PASSIVE THRU/OUTPUT 5 +60 20 6 50 100 200 500 Hz 1k 2k 5k 10k 20k 4 SL4 6 CH3 28 26 24 30 (dB) 22 CH4 6 16 12 18 20 28 26 24 30 (dB) 22 SIG CLIP PROT SATL1 MUTE 6 24 12 2 CLIP 24 12 6 LIMIT MUTE OUTPUT LEVEL 3 CLIP 24 12 6 LIMIT MUTE OUTPUT LEVEL 4 CLIP 24 12 6 LIMIT MUTE OUTPUT LEVEL 5 CLIP 24 12 6 LIMIT MUTE OUTPUT LEVEL ALTO Connetor pack REVO1-CNP 1 CLIP LIMIT 6 4 SERIAL SUBR1 SUBR2 SUBR3 SUBR4 750W D4 3-WAY STEREO DIGITAL CROSSOVER MAXIDRIVE3.4+ MUTE OUTPUT LEVEL R LTO SR3 BI-AMP +70 LINK 1 CH2 SR2 LINK 2 SR1 LINK 3 SATR1 SATR3 SATR2 SATR1 Subwoofer REVO SUB118P SUBL3 SUBL4 SATL6 SUB 2 SBL2 SUB 2 Apparaten skall anslutas till ON PWR OFF 3 1 TIDE DIGITAL IN 2 NEW PUSH RS485 OUT SUB 4 3 1 TIDE R LTO REVO1-CNP RS232 DESIGNED IN ITALY MADE IN CHINA REVO1-CNP RS485 IN 2 NEW PUSH SBL4 SUB 4 SL12 SL11 SL10 SL9 SL8 SL7 SL6 BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH CH2 CH4 CH2 CH4 INPUT CH2 INPUT CH4 INPUT CH2 INPUT CH4 INPUT INPUT BRIDGED CH3 BRIDGED CH1 BRIDGED CH3 BRIDGED CH1 PARALLEL CH3 PARALLEL CH1 INPUT PARALLEL CH3 INPUT PARALLEL CH1 PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH RACK1 ALTO Power Amplifiers: 4 D4 A102 14W SUB 3 jordat uttag nar den ansluts 95-240V 50/60Hz FUSE: 95-120V T500mAL till ett natverk 210-240V T315mAL AC INPUT SUB 3 SBL3 ALTO Processor MAXIDRIVE3.4+ SUB 1 SBL1 SUB 1 3 1 TIDE 3 1 TIDE CH3 CH1 CH3 CH1 CH3 CH1 CH3 CH1 SR3 6 SL3 2 NEW PUSH IN 1 SL8 2 NEW PUSH 3 1 TIDE 3 BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO 5 1 TIDE SL3 2 NEW LINK 1 2 NEW CH4 CH2 CH4 CH2 CH4 CH2 CH4 2 NEW 3 1 TIDE 3 1 TIDE 3 1 TIDE 3 1 TIDE OUTPUTS OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT 3 SL2 SL2 2 1 SR1 2 TIDE SL1 1 3 1 TIDE SL1 2 NEW PUSH 1 3 1 INPUT A 2 NEW TIDE 3 INPUT B 2 NEW TIDE 1 TIDE PUSH 3 PUSH 2 NEW LINK 3 1 TIDE 3 IN 3 3 NEW LINK 2 IN 2 2 NEW PUSH SL4 SL12 2 NEW LINK 3 SL5 SL11 2 NEW PUSH IN 3 SL5 SL6 SL10 2 NEW LINK 2 SL7 SL9 SR2 CH2 IN 2 PUSH SBL4 SBL3 SBL2 SBL1 SATL6 SATL5 SATL4 SATL3 SATL2 SUB 2 SBR2 SUB 2 SUB 3 SBR3 SUB 3 SUB 4 SBR4 SUB 4 R REVO1-CNP LTO REVO1-CNP IN 1 SR12 SR11 PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED CH2 CH4 CH2 CH4 INPUT CH2 INPUT CH4 INPUT CH2 INPUT CH4 INPUT INPUT BRIDGED CH3 BRIDGED CH1 BRIDGED CH3 BRIDGED CH1 PARALLEL CH3 PARALLEL CH1 INPUT PARALLEL CH3 INPUT PARALLEL CH1 PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH 3 1 TIDE 2 NEW 1 RACK2 3 TIDE PUSH IN 1 CH3 CH1 CH3 CH1 CH3 CH1 CH3 CH1 SR8 2 NEW PUSH ALTO Power Amplifiers: 4 D4 SR10 SR9 SL8 SL7 SL6 SUB 1 SBR1 SUB 1 3 1 TIDE 3 1 TIDE BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO 2 NEW LINK 1 2 NEW CH4 CH2 CH4 CH2 CH4 CH2 CH4 IN 2 3 1 TIDE 3 1 TIDE OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT SR9 2 NEW PUSH IN 2 SR5 SR7 2 NEW PUSH 3 1 TIDE 3 1 TIDE SR10 2 NEW LINK 2 SR6 2 NEW IN 3 3 1 TIDE 3 1 TIDE 3 1 TIDE 2 NEW 3 1 TIDE LINK 3 SR4 2 NEW SR11 SR12 2 NEW PUSH IN 3 SR4 SR5 2 NEW PUSH SBR4 SBR3 SBR2 SBR1 SATR6 SATR5 SATR4 SATR3 SATR2 E O 1 S A T 2 0 8 P SUBR3 SUBR4 Subwoofer REVO SUB118P SUBR1 SUBR2 Hardware for six REVO1 SAT208P 6 REVO SAT-HD-L per array 6 REVO SAT-HD-R per array Deploy in suspension or compression Hardware for each REVO SUB118P 1 REVO SUB-HD-L 1 REVO SUB-HD-R R SATR6 V RIGHT ARRAY SATR5 LINK 1 28 30 (dB) 18 24 OUTPUT LEVEL PASSIVE PIN1+1-: INPUT PIN2+2-: N/C SATL5 IN 1 16 12 B 6 12 THRU SATR4 LTO R 6 CH2 26 24 24 INPUT LEVEL A CLIP LIMIT INPUT SATL4 28 30 (dB) 6 CH1 22 20 18 SIG CLIP PROT 16 12 20 26 24 SIG CLIP PROT 22 20 18 SIG CLIP PROT CARD 12 The High Frequency Configurator gives you the possibility to define the best sound pressure level in front of the audience. The HFC is included in the passive crossover and work only in Passive-Mode. SUBL1 SUBL2 +90 SUBL1 SUBL2 SUBL3 SUBL4 +100 REVO S AT208P +80 ALTO Connetor pack REVO -CNP 16 12 UTILITY REVO SAT208P + SUB118P + MAXIDRIVE3.4+ SATL3 +110 MODE The frequency response is visible to the HFC in the two different position of the selector, 0dB (dotted line) and +3dB (continuous). 18 2 Frequency Response 6 CLIP Designed in Italy SATL2 S P L +3dB SATL1 d B PASSIVE ESC BI-AMP LO-MID: 400 W HIGH: 75 W IMPEDANCE: LO-MID: 8 Ohm HIGH: 8 Ohm ENTER POWER HANDLING: 400 W AES 1600 W PEAK IMPEDANCE: 8 Ohm NEXT MODEL HIGH PREV BI-AMP PIN1+1-: LO-MID PIN2+2-: HIGH 0dB EDIT The +3 dB position is normally used for the SAT208P that work in array, for covering the more distant audience. The 0dB is normally used for covering the nearest audience. DELAY PRESET REVO SAT 208P HOOK LEFT ARRAY 5. LAYOUT OF THE CONNECTOR PANEL REVO SAT208P 10. HOOK-UP: 12xSAT208P+8xSUB118P CONFIGURATION UP 1 High Frequency Configurator (HFC) 11 9. Speaker management: MAXIDRIVE3.4+ ! 6. HIGH FREQUENCY CONFIGURATOR (HFC) 1 Medium Array Configuration USER PRESET:2S18+6208U13 The below is an example of applying the HFC in four SAT208P in array. In this particular configuration, the HFC on the top speaker is set at +3 dB, and the bottom speaker 0 dB. REVO MAXIDRIVE3.4+ EDIT XOVER OP1&2 OP3&4 OP5&6 EDIT OUT EQ OP1&2 OP3&4 OP5&6 User Preset:2S18+6208U13 FILTER TYPE FILTER SHAPE FILTER FREQ LPF HPF LPF HPF LPF HPF LR24 LR24 Thru LR24 Thru LR24 125,0Hz 37,2Hz 2K00Hz 82,5Hz 2K00Hz 82,5Hz 0 +3dB 0 FILTER TYPE FILTER FREQ FLITER Q FILTER GAIN PEAK PEAK PEAK PEAK PEAK PEAK Hish6 PEAK PEAK PEAK 37,2Hz 101,0Hz 2K00 2K00 2K00 4K76Hz 10K93Hz 8K28Hz 2K00 2K00 1,95 1,95 1,00 1,00 1,00 1,0 1,95 1,00 1,00 +3,0 +6,0 0,0 0,0 0,0 -6,0 -3,0 +3,0 0,0 0,0 PEAK 4K76Hz 1,0 -6,0 Hish6 PEAK PEAK PEAK 10K93Hz 8K28Hz 2K00 1,95 1,00 1,00 -3,0 +3,.0 0,0 0,0 Default Default EQ1 EQ2 EQ3 EQ4 Default 2K00 OUTPUT GAIN OP1&2 OP3&4 OP5&6 -3dB 0dB(Default) 0dB(Default) +3dB 0dB FILTER SELECT Default Default Default +3dB 0 EQ1 EQ2 EQ3 EQ4 EQ5 EQ1 EQ2 EQ3 EQ4 EQ5 EQ5 Default EDIT PHASE FLOOR 2 Small Array Configuration This is the example of the HFC application at two SAT208P in a small array, with tilted speaker set at +3 dB and the bottom speaker at 0 dB. Do not stack more than two SAT208P speaker on the pole. Be sure to lock the two speaker cabinets, with the original hardware. +3dB EDIT POLARITY OP1&2 OP3&4 OP5&6 EDIT OP1&2 OP3&4 OP5&6 10 0dB NORMAL NORMAL NORMAL COMP./LIM SLOW FAST LIM. LIM. 16.0 14.0 FAST LIM. 14.0 7 8. DEPLOYING THE SYSTEM IN SUSPENSION & COMPRESSION 7. REVO MAXIMUM ARRAY SIZE 1 REVO Array Frame 1 Suspension The following table defines the maximum number of speakers that may be suspended using the REVO FB-1 array frame. A security design factor is maintained for the speaker configurations indicated in the table. +3dB Maximum quantity of REVO SAT208P in array Maximum quantity of REVO SUB118P in array 2xSAT 0 3xSAT 4xSAT 5xSAT 6xSAT 1xSUB 1xSUB 0 Max 0 +3dB Max +3dB 2 Suspension Safety Warning +3dB +3dB +3dB 45 Never exceed the maximum recommended speaker cabinet listed on the table. Research and understand the local regulation and requirements of the country where you intend to install the line array. A correct assemble of all REVO hardware is required for safety suspension system. +3dB 30 +3dB 3 Array Frame Connection REVO FB-1frame is connected to REVO SAT-HD-L and REVO SAT-HD-R with ALTO quick release pins. 0dB 0dB 2 Compression 30 +3dB +3dB +3dB 4 Lock The Loudspeakers Together +3dB +3dB 15 Any time two or more SAT208P and SUB118P are arrayed together, they must be mechanically secured to each other. See the diagram below for details. 0dB FLOOR 8 9