1
Download User`s Manual
Transcript
12 SUBL1 SUBL2 Subwoofer REVO SUB118P REVO SAT208P SATL4 SATL3 SATL2 SATL1 LEFT ARRAY A102 30 (dB) CH1 CH2 6 18 26 24 28 30 (dB) 22 20 16 12 SIG CLIP PROT 26 24 28 22 20 18 SIG CLIP PROT 6 CH3 6 16 12 18 20 26 24 28 30 (dB) 22 SIG CLIP PROT CH4 6 16 12 18 20 26 24 28 30 (dB) 22 SIG CLIP PROT SBL1 SUB 1 14W Apparaten skall anslutas till SBR1 SUB 3 OFF ON PWR 3 1 TIDE DIGITAL IN 2 NEW PUSH jordat uttag nar den ansluts 95-240V 50/60Hz FUSE: 95-120V T500mAL till ett natverk 210-240V T315mAL AC INPUT SBL2 SUB 2 RS485 OUT 3 1 TIDE RS485 IN 2 NEW SR5 SR4 SL5 SL4 SR3 SR2 SL3 SL2 BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH BRIDGED PUSH CH2 CH4 CH2 INPUT CH4 CH2 CH4 INPUT CH2 INPUT CH4 INPUT BRIDGED CH3 INPUT BRIDGED CH1 BRIDGED CH3 BRIDGED CH1 INPUT PARALLEL CH3 INPUT PARALLEL CH1 PARALLEL CH3 INPUT PARALLEL CH1 PUSH PUSH PUSH PUSH PUSH PUSH PUSH PUSH NEXT RS232 DESIGNED IN ITALY MADE IN CHINA REVO1-CNP PUSH SBR2 SUB 4 CARD PREV ALTO Power Amplifiers: 4 D4 ALTO Connetor pack REVO -CNP 16 12 PRESET DELAY UTILITY EDIT SUBL1 SUBL2 SUBR1 SUBR2 MODE A 3 1 TIDE 5 SR5 2 4 3 1 OUTPUTS 3 SL4 2 NEW CH2 CH4 CH2 CH4 CH2 CH4 CH2 CH4 BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO BRIDGED MONO CH1 CH3 CH1 CH3 CH1 CH3 CH1 CH3 OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT CLIP 3 1 TIDE SL5 2 NEW 4 2 CLIP 2 1 3 1 TIDE PUSH NEW CLIP 1 TIDE 1 3 2 INPUT A 3 1 NEW INPUT B 2 NEW TIDE 3 PUSH 2 NEW LINK 3 750W 4 D4 3-WAY STEREO DIGITAL CROSSOVER MAXIDRIVE3.4+ MUTE TIDE 6 OUTPUT LEVEL PUSH 24 12 6 LIMIT MUTE IN 3 5 OUTPUT LEVEL SL1 24 12 6 LIMIT MUTE OUTPUT LEVEL LINK 2 24 12 6 LIMIT MUTE SR1 3 OUTPUT LEVEL SR3 SL3 SR2 SL2 6 SR4 1 TIDE 3 NEW IN 2 PUSH 2 NEW 6 12 24 SL1 MUTE TIDE LINK 1 2 CLIP OUTPUT LEVEL LIMIT 24 12 6 MUTE CLIP 1 LIMIT OUTPUT LEVEL 6 24 12 CLIP LIMIT B 6 24 18 12 CLIP INPUT LEVEL PUSH IN 1 SR1 ESC ENTER SBR2 SBR1 SBL2 SBL1 SATR4 SATR3 SATR2 SATR1 SATL4 SATL3 SATL2 SATL1 ALTO Processor MAXIDRIVE3.4+ REVO SAT208P SATR4 SATR3 SATR2 SATR1 RIGHT ARRAY SUBR1 SUBR2 Subwoofer REVO SUB118P Hardware for four REVO SAT208P 4 REVO SAT-HD-L per array 4 REVO SAT-HD-R per array Deploy in suspension or compression Hardware for each REVO SUB118P 1 REVO SUB-HD-L 1 REVO SUB-HD-R REVO1 SERIES STEREO LINE ARRAY WITH SUBS (8 STA208P+4 SUB118P) HOOK 10. HOOK-UP:8xSAT208P+4xSUB118P CONFIGURATION 4. REVO SUB118P TECHNICAL SPECIFICATION UP Model No. Configuration Operating Frequency Range Frequency Response Maximum Peak SPL Power Rating (AES Standard) Transducers Low Crossover modes System Sensitivity (1w@1mt) Nominal Impedance Suspension / Mounting Enclosure Input Connectors Dimension (H x W x D) Net Weight (Kg/lbs) REVO SUB 118P DIRECT INPUT REVO SUB 118P Vented Subwoofer, Passive or Direct 37 Hz~200 Hz (-10 dB) 43 Hz~200 Hz (+/- 3 dB) 129 dB SPL (calculated) 750 W/1500 W 18" Subwoofer, 4" high-power voice coil Ceramic magnet, weather resistant cone. Passive, Active with externally selector in direct connection 97 dB SPL, passive version 8 ohm, nominal Single 36 mm pole socket, four integrated point For line array suspension, two handle, four optional wheel 18 mm calibrated plywood, black finish, perforated metal grille Two SPK N-L 4 type, Passive, Input 1+/1- Output 1+/1Direct 1+/1- ( 2 SPK parallel ) with externally selector 620 mm x 620 mm x 700 mm (24.4" x 24.4" x 27.5") 51.8 Kg (113.4 lbs) 1. "Frequency Response" is measured in half-space condition. 2. AES filtered pink noise with 6 dB crest factor for 2 hours. Rear panel REVO SUB 118P BLOCK DIAGRAM POWER HANDLING: 750 W AES 1500 W PEAK IMPEDANCE: 8 Ohm SERIAL MODEL Designed in Italy PASSIVE THRU/OUTPUT 5
