Download Centurion - MedWrench

Instruction
and
Technical
Manual
D
2000 & K/R
INDEX
Part One
(This Section must be read and utilised for safety)
• General Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
• Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
• Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
• Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
• Fault Finding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
• Chemical Resistance Tables . . . . . . . . . . . . . . . . . . . . . . 9
Part Two
EB Range:
• Operating Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
• User Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
• Circuit Board diagrams . . . . . . . . . . . . . . . . . . . . . . . . . 16
• General Technical Information . . . . . . . . . . . . . . . . . . . . 18
Part Three
1000 Series:
• Operating Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
• Troubleshooting Guide. . . . . . . . . . . . . . . . . . . . . . . . . . 23
• Circuit Board diagrams . . . . . . . . . . . . . . . . . . . . . . . . . 27
• General Technical Information . . . . . . . . . . . . . . . . . . . . 32
Part Four
2000 Series, K Series and KR Series:
• Operating Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
• Troubleshooting Guide. . . . . . . . . . . . . . . . . . . . . . . . . . 39
• Operating Manual KR Series (Refrigerated) . . . . . . . . . . . . 40
• Troubleshooting Guide. . . . . . . . . . . . . . . . . . . . . . . . . . 41
• Circuit Board diagrams . . . . . . . . . . . . . . . . . . . . . . . . . 42
• General Technical Information . . . . . . . . . . . . . . . . . . . . 48
• Test 13/16 Via LED Display. . . . . . . . . . . . . . . . . . . . . . . 54
Part Four
2000 Series, K Series and KR Series:
2030 (6,000rpm Cell Washer centrifuge with rotor)
2050
(2,000rpm Cytology centrifuge with rotor)
2010
(13,300rpm centrifuge with choice of rotor)
2010H
(12,000rpm Haematocrit centrifuge with rotor)
2015
(15,000rpm centrifuge with choice of rotor)
2020
(6,000rpm centrifuge with choice of rotor)
2040
(3,800rpm centrifuge with rotor and adaptors)
2041
(6,000rpm centrifuge with choice of rotor)
MULTI ROTOR CENTRIFUGES:
K2080
(13,300rpm centrifuge with choice of rotor)
K2042
(12,000rpm centrifuge with choice of rotor)
K220
(15,000rpm centrifuge with choice of rotor)
K240
(15,000rpm centrifuge with choice of rotor)
K240R
(15,000rpm refrigerated centrifuge with rotors)
K280R
(15,000rpm refrigerated centrifuge with rotors)
37
38
Lid Open
Press when LED display
indicates OPEn.
Acceleration/Deceleration
Start/Stop
To start, shut lid and press Start.
Centrifuge will run to set time and then
automatically brake to STOP.
Press STOP if you need to stop before
timer ends
To Increment Accel Rate:
Hold down Function and press
Speed Up (see Accel LED on speed
display)
To Increment Decel Rate:
Hold down Function and press
Speed Down (see Decel LED on
speed display)
To Increment Memory No’s:
Hold down Function and press
Pulse (see memory LED on speed
display)
For Rcf/Rpm mode:
Hold down Function and press Lid
Open (see correct dot on speed
display)
Function
Scientific
Centurion
Time
Pulse (secs)
Hold down Pulse to run
centrifuge. Time (in seconds)
counted up from zero on
time display.
Release button when desired
time is reached.
Memory
2000 and K MODELS
OPERATING MANUAL
This will recall the required program.
While still holding Function, press
Recall.
Hold down Function and press
Memory until no. 6 shows in display.
To Recall a Program:
e.g from memory number 6
This will save the information to the
required number.
While still holding Function, press
Store.
Select Speed and Time parameters.
Hold down Function and press
Memory until no. 6 shows in display.
To Set a Program:
e.g in memory number 6
Programs
39
WAIt
You have tried to open the lid. Please wait for 10
seconds and try again. If the lid still does not
open: check that the rotor has stopped turning,
insert lid release tool into side hole (on right) and
lever down. The lid will ‘pop’ open.
Lid?
The lid has opened during the run. The motor
will now brake. After it has come to a complete
stop you may open the lid. Check that the lid is
correctly shut. If Lid? still showing please
contact your service department.
OPEn
The rotor has stopped spinning. You may now
open the lid. Press the ‘Lid Open’ button.
tAcho?
The rotor has not turned in 5 seconds. Check
that nothing is preventing the rotor from turning
i.e tall tubes or packaging. If tAcho? still
showing please contact your service department.
TROUBLESHOOTING
rotor?
K2 Series only.
The rotor has not been recognised. Safety speed
will automatically be selected. Try and run
again, check its max speed. If rotor? still
showing please contact your service department.
baL?
An imbalance has occurred. Check that the
tubes are correctly placed in the rotor. If tubes
are correctly placed and baL? still showing please
contact your service department.
40
Lid Open
Press when LED display
indicates OPEn.
Temperature Up/Down
Memory
Time
Pulse (secs)
Hold down Pulse to run
centrifuge. Time (in seconds)
counted up from zero on
time display.
Release button when desired
time is reached.
Acceleration/
Deceleration
K SERIES REFRIGERATED MODELS
OPERATING MANUAL
Start/Stop
To start, shut lid and press Start.
Centrifuge will run to set time and then
automatically brake to STOP.
Press STOP if you need to stop before
timer ends
To Increment Accell Rate:
Hold down Function and press
Speed Up (see Accel LED on speed
display)
To Increment Decell Rate:
Hold down Function and press
Speed Down (see Decel LED on
speed display)
To Increment Memory No’s:
Hold down Function and press
Pulse (see memory LED on speed
display)
For Rcf/Rpm mode:
Hold down Function and press Lid
Open (see correct dot on speed
display)
Function
Scientific
Centurion
This will recall the required program.
While still holding Function, press
Recall.
Hold down Function and press
Memory until no. 6 shows in display.
To Recall a Program:
e.g from memory number 6
This will save the information to the
required number.
While still holding Function, press
Store.
Select Speed and Time parameters.
Hold down Function and press
Memory until no. 6 shows in display.
To Set a Program:
e.g in memory number 6
Programs
41
WAIt
You have tried to open the lid. Please wait for 10
seconds and try again. If the lid still does not
open: check that the rotor has stopped turning,
insert lid release tool into side hole (on right) and
lever down. The lid will ‘pop’ open.
Lid?
The lid has opened during the run. The motor
will now brake. After it has come to a complete
stop you may open the lid. Check that the lid is
correctly shut. If Lid? still showing please
contact your service department.
OPEn
The rotor has stopped spinning. You may now
open the lid. Press the ‘Lid Open’ button.
tAcho?
The rotor has not turned in 5 seconds. Check
that nothing is preventing the rotor from turning
i.e tall tubes or packaging. If tAcho? still
showing please contact your service department.
TROUBLESHOOTING
rotor?
K2 Series only.
The rotor has not been recognised. Safety speed
will automatically be selected. Try and run
again, check its max speed. If rotor? still
showing please contact your service department.
baL?
An imbalance has occurred. Check that the
tubes are correctly placed in the rotor. If tubes
are correctly placed and baL? still showing please
contact your service department.
GND
VCC
100R
100R
R2
R1
J1
100n
C1
100n
C2
LID SOL OUT
HEATER OUT
LID SOL IN
HEATER IN
RS232 TX OUT
RS232 RX IN
BUZZER OUT
BUZZER IN
RS232 TX IN
RS232 RX OUT
TXD
RXD
J12
4
3
2
1
DRIVE RJ45
TSTS+
PSU RST
+12V
BUZZER
LID SOL
HEATER
J4
+12v
2
1
TS +VE
TS -VE
BAL SW
TACHO
LID SW
ROTOR SENSE
J2
+24V
4
3
2
1
LID SWITCH 1
LID SWITCH 2
LID SOLENOID 1
LID SOLENOID 2
BAL SW OUT
TACHO OUT
LID SW OUT
R SENSE OUT
J5
VCC
4
3
AC1
AC2
PSU RST
PSU10
PSU10.SCH
MP240D4
I/P-
I/P+
SSR1
Size:
A4
Number:
VS1161/C1
VS1161 Centrifuge Control - Main
Title
J3
+12V
BUZZER +VE
BAL SW IN
TACHO IN
LID SW IN
R SENSE IN
3
2
1
BUZZER 0V
UP10
UP10.SCH
2
1
9 VAC
9 VAC
IO10
IO10.SCH
VSS
VDD
Revision:1.0
GND
VCC
+24V
+12V
+5V
0v
AC2/-
AC1/+
J6
+24v
+12v
VCC
GND
2
1
HEATER
8
7
6
5
4
3
2
1
BALANCE SWITCH 1
BALANCE SWITCH 2
TACHO +VE
TACHO O/P
TACHO 0V
SENSE +VE
SENSE O/P
SENSE 0V
3
2
1
HEATER
42
43
AC2
AC1
470u
+ C12
D1
1N4006
1N4006
D2
100R
R3
BR1
W02G
2200u
+ C15
4700u
+ C13
C3
100n
R4
100k
4
1
DEL
VI
U1
L387A
GND
3
RST
VO
2
5
C5
100n
C6
100n
C7
100n
A4
Number:
VS1161/PSU
VS1161 Centrifuge Control - PSU
Size:
Title
100u
+ C14
C4
100n
Revision:1.0
C8
100n
C9
100n
0v
+5V
PSU RST
+12V
+24V
VCC
R13
1M
R10
1M
1M
R12
GND
C17
22p
11.059MHz
X1
BUZZER
PSU RST
PSU RESET
1u
+ C19
Q2
BC182B
1M
GND
100n
D5
1N4148
17
16
12
13
14
15
29
30
TEMP SENSOR
TS-
TS+
+12V
A0
GND
GND
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
7
5
6
13
12
10
9
5
4
2
1
3
20
22
10
9
8
7
6
5
4
3
25
24
21
23
2
26
27
1
2
1N4148
R14
74HC573
1D
2D
3D
4D
5D
6D
7D
8D
19
18
17
16
15
14
13
12
11
10
2
3
4
5
6
7
8
9
1Q
2Q
3Q
4Q
5Q
6Q
7Q
8Q
1
6
D6
1N4148
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
A8
A9
A10
A11
A12
A13
A14
A15
OC
C
U5
1
2
3
4
5
6
7
8
39
38
37
36
35
34
33
32
21
22
23
24
25
26
27
28
C10
R15
10k
Q1
BC212B
RD/P3.7
WR/P3.6
INT0/P3.2
INT1/P3.3
T0/P3.4
T1/P3.5
PSEN
ALE/PROG
TXD/P3.1
RXD/P3.0
T2/P1.0
T2EX/P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
A8
A9
A10
A11
A12
A13
A14
A15
D4
10k
TACHO
R11
1M
LID SOL
LID SOLENOID
TACHO
TXD
ROTOR SENSE
TXD
ROTOR SENSE
RXD
RXD
R16
HEATER
SAB80C32P
XTAL1
XTAL2
EA/VPP
RST
BUZZER
19
18
31
9
HEATER CONTROL
GND
C18
22p
GND
1
11
TLC549
CLK
CS
DO
U9
74CH00
74CH00
U11D
U11C
74CH00
74CH00
U11B
U11A
93C66
CLK
CS
ORG
DI
U4
DO
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
REF-
REF+
AIN
27C256/512
E
G/VPP
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
U2
3
1
2
11
8
6
3
4
11
12
13
15
16
17
18
19
+12V
GND
VCC
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
GND
R24
2k2
9
8
12
11
13
14
10
6
5
7
19
18
17
16
15
14
13
12
19
18
17
16
15
14
13
12
7
1
1D
2D
3D
4D
5D
6D
7D
8D
OC
C
1D
2D
3D
4D
5D
6D
7D
8D
OC
C
GND
+12V
6
5
LM2904N
3
U10A
2
GND
RV2
5k
ZERO
R23
R21
18k
DIG8
DIG7
DIG6
DIG5
DIG4
DIG3
DIG2
DIG1
18
21
22
17
20
23
16
15
2k2
VCC
SEGDP
SEGA
SEGB
SEGC
SEGD
SEGE
SEGF
SEGG
PB1
4
27
3
1
25
2
24
26
GND
GND
GND
VDD
68k
D8
D7
D6
D5
D4
D3
D2
D1
DP
SEGA
SEGB
SEGC
SEGD
SEGE
SEGF
SEGG
2
3
4
5
6
7
8
9
1
11
2
3
4
5
6
7
8
9
1
11
FN1
R20
100n
C11
ICM7228AIPI
MODE
WRITE
ID0
ID1
ID2
ID3
ID4(SHUT)
ID5(DEC)
ID6(HEXA)
ID7(DATA)
U8
74HC573
1Q
2Q
3Q
4Q
5Q
6Q
7Q
8Q
U7
74HC573
1Q
2Q
3Q
4Q
5Q
6Q
7Q
8Q
LM2904N
U10B
SCALE
RV1
20k
A0
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
U6
VDD
PB2
PB3
TIME +
LED1
DA56-11GWB
PB4
PB6
SPEED HI
PB5
PB7
FN5
FN4
PB8
9
7
12
5
6
8
10
11
13
4
17
18
1
2
3
15
16
14
SEGDP
SEGG
SEGC
SEGB
SEGA
SEGF
SEGE
SEGD
DIG1
SEGDP
SEGG
SEGC
SEGB
SEGA
SEGF
SEGE
SEGD
DIG2
DIG7
SEGA
SEGB
SEGC
SEGD
SEGE
SEGF
SEGG
SEGDP
DIG8
SEGA
SEGB
SEGC
SEGD
SEGE
SEGF
SEGG
SEGDP
14
16
15
3
2
1
18
17
4
13
11
10
8
6
5
12
7
9
GND
b
dp
U3
TIME a
g
c
4
f
d
8
FN2
b
e
dp
c
dp2
g2
f2
e2
d2
c2
b2
a2
com2
dp1
g1
f1
e1
d1
c1
b1
a1
com1
a
g
d
LED3
DA56-11GWB
e
f
d
g
a
dp
e
f
TE M P
c
b
c
b
dp
PB9
10k
10k
R19
10k
R18
R17
RP1
10k
Size:
A3
1
LID SWITCH
2
3
4
5
6
7
8
9
BALANCE SWITCH
PB11
LID SW
PB10
GND
BAL SW
TEMP -
TEMP +
LED2
DA56-11GWB
e
f
d
g
a
dp
e
f
SPEED LO
c
b
d
g
a
LED4
DA56-11GWB
e
f
d
g
a
dp
f
e
T IM E
c
b
d
g
a
Number:
VS1161/UP
Revision:1.0
VS1161 Centrifuge Control - uP/Keys/Display
Title
d
g
a
com1
a1
b1
c1
d1
e1
f1
g1
dp1
com2
a2
b2
c2
d2
e2
f2
g2
dp2
FN3
DIG3
SEGA
SEGB
SEGC
SEGD
SEGE
SEGF
SEGG
SEGDP
DIG4
SEGA
SEGB
SEGC
SEGD
SEGE
SEGF
SEGG
SEGDP
14
16
15
3
2
1
18
17
4
13
11
10
8
6
5
12
7
9
c
b
dp
com1
a1
b1
c1
d1
e1
f1
g1
dp1
com2
a2
b2
c2
d2
e2
f2
g2
dp2
DIG5
SEGA
SEGB
SEGC
SEGD
SEGE
SEGF
SEGG
SEGDP
DIG6
SEGA
SEGB
SEGC
SEGD
SEGE
SEGF
SEGG
SEGDP
14
16
15
3
2
1
18
17
4
13
11
10
8
6
5
12
7
9
c
b
dp
com1
a1
b1
c1
d1
e1
f1
g1
dp1
com2
a2
b2
c2
d2
e2
f2
g2
dp2
f
e
44
SPEED -
SPEED +
VCC
45
GND
9
74HC14
U12D
8
GND
RS232 TX IN
RS232 RX OUT
LID SOL IN
HEATER IN
BUZZER IN
R SENSE IN
TACHO IN
BAL SW IN
LID SW IN
13
74HC14
U12F
12
R33
4k7
VCC
R36
4k7
VCC
R38
470R
VCC
R39
470R
VCC
GND
100k
10k
C22
10n
R7
R27
GND
100k
10k
C23
10n
R8
R28
GND
100k
47k
C21
10n
R6
R26
C20
10n
100k
47k
GND
R5
R25
VCC
R9
4k7
5
11
3
1
100n
C25
GND
GND
VCC
GND
R22
4k7
74HC14
U12C
74HC14
U12E
74HC14
U12B
74HC14
U12A
13
8
11
10
1
3
6
10
4
2
R1 IN
R2 IN
T1 IN
T2 IN
C1+
C1 -
100n
100n
C24
C16
R29
4k7
4k7
R32
4k7
R31
4k7
R30
VCC
2
6
16
GND
R1 OUT
R2 OUT
T1 OUT
T2 OUT
C2+
C2 -
U13
MAX202CPE
V+
VVCC
GND
15
12
9
14
7
4
5
Q4
BC182B
100n
C26
Q5
BC182B
GND
Q6
BC182B
R35
4k7
+12V
4k7
R34
GND
+24V
TACHO OUT
Size:
A3
Number:
VS1161/IO
Revision: 1.0
RS232 TX OUT
RS232 RX IN
LID SOL OUT
HEATER OUT
BUZZER OUT
R SENSE OUT
VS1161 Centrifuge Control - I/O
Title
Q3
BUZ71A
D3
1N4006
LID SW OUT
BAL SW OUT
VS1161/C1 ISS A Part list
Itm Qty References Description
1 . . . . . . 1. . . . . . . BR1 . . . . . . . . . . . Bridge Rectifier 1.5A 200V Glass pass, W02G, Any, W02G (RS 659-826)
2 . . . . . . 2. . . . . . . C17. . . . . . . . . . . . C18 Capacitor Min Ceramic Plate, 22p, Phillips, 680 34229 (RS 167-0442)
3 . . . . . . 14 . . . . . C1 C2 C3 C4 C5 C6 . . Capacitor Multilayer Ceramic 50v, 100n, Any, (RS 264-4949)
C7 C8 C9 C10 C16
C24 C25 C26
4 . . . . . . 1. . . . . . . C11 . . . . . . . . . . . . Capacitor Multilayer Ceramic 50v, 100n, Any, (RS 264-4949) [RF]
5 . . . . . . 4. . . . . . . C20 C21 C22 C23 . . . Capacitor Multilayer Ceramic 50v, 10n, Any, (RS 264-4832)
6 . . . . . . 1. . . . . . . C14. . . . . . . . . . . . Capacitor Radial Al Elec (low ESR) 25v, 100u, ELNA RSH Series, (FEC 108-834)
7 . . . . . . 1. . . . . . . C15. . . . . . . . . . . . Capacitor Radial Al Elec 25v, 2200u, Rubcon YXF series, (RS 191-7791)
8 . . . . . . 1. . . . . . . C12. . . . . . . . . . . . Capacitor Radial Al Elec 25v, 470u, Rubicon YXF series, (RS 191-7779)
9 . . . . . . 1. . . . . . . C13. . . . . . . . . . . . Capacitor Radial Snap in 35V, 4700u, Any, (RS 127-458)
10. . . . . . 1. . . . . . . C19. . . . . . . . . . . . Capacitor sub min Radial Al Elec 50v , 1u, Any, (RS 205-1959)
11. . . . . . 1. . . . . . . J12 . . . . . . . . . . . . Connector RJ45 4/4 Vertical, CON4, Stewart Connector Systems Inc, SS-6544-NF
(RS 437-187)
12. . . . . . 1. . . . . . . X1. . . . . . . . . . . . . Crystal HC18U AT Cut, 11.059MHz, Any, (RS 226-1774)
13. . . . . . 3. . . . . . . D1 D2 D3 . . . . . . . . Diode Power 1A 800v, 1N4006, Any, (RS 261-974)
14. . . . . . 3. . . . . . . D4 D5 D6 . . . . . . . . Diode Signal, 1N4148, Any, (RS 271-606)
15. . . . . . 1. . . . . . . J3. . . . . . . . . . . . . Header 0.1” 3W Friction Lock, CON3, AMP, MTA series (RS 132-0361) [N]
16. . . . . . 1. . . . . . . J5. . . . . . . . . . . . . Header Pin PCB 2W, CON2, Molex, 26-48-1245 (part) (FEC 151-899)
17. . . . . . 1. . . . . . . J6. . . . . . . . . . . . . Header Pin PCB 3W, CON3, Molex, 26-48-1245 (part) (FEC 151-899) [RF]
18. . . . . . 1. . . . . . . J4. . . . . . . . . . . . . Header straight 0.1” 2W , CON2, AMP, MTA series (RS 132--0355) [RF]
19. . . . . . 1. . . . . . . J2. . . . . . . . . . . . . Header straight 0.1” 4W , CON4, AMP, MTA series (RS 132-0377)
20. . . . . . 1. . . . . . . J1. . . . . . . . . . . . . Header straight 0.1” 8W , CON8, AMP, MTA series (RS 132-0377)
21. . . . . . 1. . . . . . . U9. . . . . . . . . . . . . IC ADC 8 bit serial, TLC549, Texas Inst, TLC549IP (RS 650-093) [RF]
22 . . . . . 1. . . . . . . U2. . . . . . . . . . . . . IC CMOS EPROM 256k 200ns, 27C256/512, Any,(Any)
23 . . . . . 1. . . . . . . U4. . . . . . . . . . . . . IC CMOS Serial EEPROM 4k, 93C66, SGS, ST93C66B1 (RS 322-3874)
24. . . . . . 1. . . . . . . U12. . . . . . . . . . . . IC HC CMOS Hex Schmitt Inverter, 74HC14, Any, (RS 300-568)
25. . . . . . 3. . . . . . . U5 U6 U7 . . . . . . . . IC HC CMOS Octal transparent latch, 74HC573, Any, (RS 300-754)
26. . . . . . 1. . . . . . . U11. . . . . . . . . . . . IC HC CMOS Quad NAND, 74CH00, Any, (RS 301-224)
27. . . . . . 1. . . . . . . U8. . . . . . . . . . . . . IC LED Display driver, ICM7228AIPI, Intersil, (RS 648-696)
28. . . . . . 1. . . . . . . U3. . . . . . . . . . . . . IC Microprocessor 80C32 12MHz, SAB80C32P, Any, (RS 427-720)
29. . . . . . 1. . . . . . . U13. . . . . . . . . . . . IC RS232 Transceiver, MAX202CPE, Any, (Any)
30 . . . . . 1. . . . . . . U1. . . . . . . . . . . . . IC Voltage Regulator +5v with reset output, L387A, SGS, L387A (RS 263-267)
31. . . . . . 1. . . . . . . U10. . . . . . . . . . . . IC dual op-amp, LM2904N, Nati Semi, LM2904N (RS 810-273) [RF]
32. . . . . . 3. . . . . . . LED1 LED2 LED4. . . . LED Dual 7 Segment Display Green Common Anode, DA56-11GWB, Kingbright,
DA56-11GWB (????)
33. . . . . . 1. . . . . . . LED3 . . . . . . . . . . . LED Dual 7 Segment Display Green Common Anode, DA56-11GWB, Kingbright,
DA56-11GWB (????) [RF]
34 . . . . . 1. . . . . . . Q3. . . . . . . . . . . . . MOSFET N Channel 50v 16A, BUZ71A, Any, (RS 325-9479)
35. . . . . . 1. . . . . . . RP1. . . . . . . . . . . . R Pack 8 commoned 9 pin SIL 5%, 10k, Any, (RS 140-978)
36 . . . . . 1. . . . . . . SSR1 . . . . . . . . . . . Relay Solid state 4A 240vac, MP240D4, CRYDOM, MP240D4 (RS 291-1823) [RF]
37. . . . . . 1. . . . . . . R3. . . . . . . . . . . . . Resistor Carbon Film 1W 5%, 100R, Any, (RS 131-772)
38 . . . . . 2. . . . . . . R1 R2. . . . . . . . . . . Resistor Metal Film 0.25W 1%, 100R, Any, (RS 148-269)
39. . . . . . 5. . . . . . . R4 R5 R6 R7 R8 . . . . Resistor Metal Film 0.25W 1%, 100k, Any, (RS 148-972)
40 . . . . . 7. . . . . . . R15 R16 R17 R18 R19 Resistor Metal Film 0.25W 1%, 10k, Any, (RS R27 R28 148-736)
41. . . . . . 1. . . . . . . R21. . . . . . . . . . . . Resistor Metal Film 0.25W 1%, 18k, Any, (RS 148-792) [RF]
42. . . . . . 5. . . . . . . R10 R11 R12 R13 R14 Resistor Metal Film 0.25W 1%, 1M, Any, (RS 149-228)
43. . . . . . 2. . . . . . . R23 R24. . . . . . . . . Resistor Metal Film 0.25W 1%, 2k2, Any, (RS 148-584) [RF]
44 . . . . . 2. . . . . . . R38 R39. . . . . . . . . Resistor Metal Film 0.25W 1%, 470R, Any, (RS 148-427)
45. . . . . . 2. . . . . . . R25 R26. . . . . . . . . Resistor Metal Film 0.25W 1%, 47k, Any, (RS 148-893)
46 . . . . . 8. . . . . . . R9 R29 R30 R32 R33 Resistor Metal Film 0.25W 1%, 4k7, Any, (RS R34 R35 R36 148-663)
47. . . . . . 2. . . . . . . R22 R31. . . . . . . . . Resistor Metal Film 0.25W 1%, 4k7, Any, (RS 148-663) [RF]
48 . . . . . 1. . . . . . . R20. . . . . . . . . . . . Resistor Metal Film 0.25W 1%, 68k, Any, (RS 148-938) [RF]
49. . . . . . 1. . . . . . . RV1. . . . . . . . . . . . Resistor POT vertical 20T, 20k, Bourns, 3296W (RS 160-102) [RF]
50 . . . . . 1. . . . . . . RV2. . . . . . . . . . . . Resistor POT vertical 20T, 5k, Bourns, 3296W (RS 160-089) [RF]
51. . . . . . 7. . . . . . . PB2 PB3 PB4. . . . . . Switch Push Button , SW-PB, ITT, D6 Flat PB7 PB8 (Arrow 525017)
PB5 PB6
52. . . . . . 1. . . . . . . PB11 . . . . . . . . . . . Switch Push Button , SW-PB, ITT, D6 Flat (Arrow 525017) [N]
53. . . . . . 3. . . . . . . PB1 PB9 PB10 . . . . . Switch Push Button , SW-PB, ITT, D6 Flat (Arrow 525017) [RF]
54 . . . . . 3. . . . . . . Q2 Q4 Q6. . . . . . . . Transistor Small Signal NPN, BC182B, Any, (Any)
55 . . . . . 1. . . . . . . Q5. . . . . . . . . . . . . Transistor Small Signal NPN, BC182B, Any, (Any) [RF]
56 . . . . . 1. . . . . . . Q1. . . . . . . . . . . . . Transistor Small Signal PNP, BC212B, Any, (Any)
46
Additional parts
Socket for U2
Heatsink and clip for U1
Build Options
[RF] = refrigerated version only
[N] = normal version only
47
Tachometer
• The Tachometer is a horseshoe LED type, 5volt, sensing dark and light current off the butterfly interrupter.
• The only adjustment necessary is to make sure the sensor is central to the horseshoe array.
• Apart from a light haired brush to the sensors, to remove dust no other maintenance is necessary.
Tacho sensor
Tacho connection to J1 (near C1/C23)
Lid Locking Mechanism and Solenoid
• The two point locking mechanism is released by a 12-volt solenoid, capacitor at 20 volts, for a brief period.
• This method gives maximum power for a short period without the possibility of burning out the Solenoid
Coil, by remaining on, thus by constantly pressing the lid open button, a wait message appears on the LED
this is while the capacitor charges (approximately 4 seconds).
• The lid open sensor is a V3 microswitch, wired normally open.
• The actuation is on the latch arm; adjustments can be made only by removing the front panel and trimming
the V3 microswitch arm. The switch is situated front right above the Solenoid (see Picture below).
• The Solenoid plug is a 4 way connection to J5 on the Circuit Board (see Picture below)
• Apart from adjustment to the Microswitch, or Lid latches (on the lid) dependant on wear.
• No other maintenance is necessary
Solenoid and Microswitch:
Microswitch arm
48
Lid latch to lid
(correct position aligned to side)
Lid System Connection:
Lid system plug J2
Imbalance Detector
• The imbalance Detector is a V3 microswitch wired normally closed.
• A break in the circuit actuates the motor brake and the rotor comes
to a safe stop.
• The circuit is 5 volt from the main board.
• The adjustment is by two pozihead screws on the underside of the
base plate.
• Release and push forward or backwards to adjust.
Imbalance arm
NOTE: a 3mm gap should be between the stop and the detector arm for normal use.
Imbalance plug to board position J1
(near C21)
Correct gap (3mm)
49
Mains Inlet Filter
• The Mains inlet is double fused, with an IEC Socket for the power source.
• It is held in place with 2 Countersunk M3 Screws.
• Fuses are 5 x 20mm 6.3 (TA) Slow blow only. R Version is 10 amp (TA)
• Wiring to filter is shown as below.
• Wiring to Inverter is EARTH to EARTH, BROWN to L1 and BLUE to L2/N
Mains inlet wiring
Mains connection to Inverter
Blue (Neutral)
Brown (Live)
Brown (Live)
Blue (Neutral)
Filter
To comply with EMC regulations a 5 amp filter is fitted.
This has been tested and complies with radiated and transmitted
specifications.
Connections are as on the Filter and should NOT be reversed
(see photograph)
Blue (Neutral)
Brown (Live)
Buzzer and Fitment (optional extra)
• The buzzer is a 12 volt type, fitted to the front panel by a tape backing.
• The connection is to J3, a 3 pin connector.
• The buzzer sounds at the end of the run, stays on for a few minutes and then shuts off (so as not to be
intrusive)
• No maintenance is necessary.
Motor Connection to Inverter
}
BLACK 11 to TH1A
BLACK to M1/U
YELLOW
BLACK 12 to TH1B
BROWN to M2/V
GREEN GROUP CONNECTOR
BLUE to M3/W
WHITE
50
Transformer and Connection
• The transformer is a 12 volt 20Va type, held in position with two flat washers, spring washers and M4 nuts.
This unit powers the circuit board (regulated down further to 5 volts), lid lock and buzzer.
• The wiring from the top is Mains voltage (brown wires). Area dependent.
• The two lower wires (as marked are 12 volt) DO NOT USE mains power here.
• These 12 volt (blue wires) pass into a Molex two pin plug to J5 on the circuit board.
Transformer position
Transformer plug position J5
Rotor Recognition Sensor (K series only)
• A Hall effect sensor, fixed to the motor top, senses magnet flux from placed magnets in the required rotor.
• A Rotor must be used with the K Series.
• The amount of small magnets per rotor are pertinent to the maximum speed of each rotor.
• The sensor counts the flux number per rotation, advising a look up table and setting the rotors paramaters
for safety.
• Maintenance. Other than checking the distance from sensor to magnet (2-6mm max) no other maintenance
is necessary.
Rotor recognition sensor
Connections to J1 near C22
51
K Refrigerated Series only:
Temperature Probe
• The Temperature probe is an AD592AN: IC Transducer.
• Wiring is to the two outer legs only, the centre leg is removed.
• The transducer is mounted in a Stainless steel M8 Shroud with Heat sink compound. The Assembly is then
bolted in position to the outer rim of the bowl (as shown).
• Twin wires are taken forward to the Circuit Board to socket J4
Replacement of Probe
• After extracting the probe and replacing, the new probe will require calibrating.
• RV1 and RV2 on the circuit Board will require “trimming” to the correct temperature.
• A thermometer accurate to 0.5ºC will be required.
• By placing the thermometer near the probe in the bowl, calibrate RV1 to 0ºC then RV2 to ambient, go back
to RV1 to recheck.
• For K280R a 7ºC offset is required and the K240R a 5ºC offset. These offsets are to allow for bowl mixing
of temperature variation over its depth.
Temperature probe connection to J4
Temperature probe housing to bowl
Refrigeration (KR Series only)
• The Compressor is a standard unit Electrolux GL60 PB charged with R134A gas at a charge 120Gms. An
equivalent can be used that has the same footprint.
• Capillary length is 3 metres of .031mm bore.
• Suction line length is 76Cm of 5/16” tubing, the dryer is a 10gm type.
• Fan is a standard mains type.
• Wiring to the compressor is shown here.
Mains power
Fan power
Refrigerated unit compressor from rear
52
Heater Wiring (KR Series only)
• The Heater is a 5.77 metre coil of 30 Ohm shrouded wire.
• This is wound between the Cooling coils and controls the temperature by pulsing on off via a solid-state
relay (SSR1).
• This is controlled by a PID system (Proportional, Integral, Derivative) for accuracy.
Connection to board is as below. Mains wiring to connector is also shown.
Heater wire plug to J6
Mains plug for compressor fan
and heater
Inverter Connections 2000, K & KR series only
• By Stuart Plug connections
Inverter connection
Board connection J12
53
E SOLD
W
RI
ON
E
OUT TH
CENT
U
RIF
TH
O
G
ES
AR
R
UG
H
OR
LD
T
CEN
U
Distributed by:
Manufactured by:
Centurion Scientific Ltd
Unit A2 Ford Airfield Industrial Estate,
Ford, Arundel, West Sussex. BN18 0HY. UK
Tel: + (0) 10 100
Fax: +44 (0) 1903 725496
e-mail: [email protected]
www.centurionscientific.co.uk