Download 1 Press - Alpine

Adjusting and Storing the Crossover
Settings (CDA-9815/CDA-9813 only)
Before performing the following procedures, refer to “About the
Crossover”(page 15).
1
Press and hold T.CORR/X-OVER for at least 2
seconds.
5
Adjustable output level: -12 to 0 dB.
To store the adjusted contents
1) Press and hold any one of the preset buttons (1
through 6) for at least 2 seconds into which you wish to
store the adjusted contents.
6
2 WAY System
2
Press BAND/TEL. to select desired parameter.
LOW (Subwoofer) → REAR → FRONT → LOW (Subwoofer)
3
Press g or f to select desired cut-off
frequency point (cross over point).
Turn the Rotary encoder to select the desired
output level.
7
For setting another channel, repeat the steps 2 to
5.
After setting, press T.CORR/X-OVER to return to
normal mode.
• About the 2way/3way system
You can switch to 2way/3way system mode with the 2way/3way
switch on the side of the unit (page 38).
Adjustable frequency bands: 20Hz to 200Hz (in 1/3
octave steps)
4
5
Adjustable slope: 0 (FLAT (OFF)), 1 (-6 dB/oct.),
2 (-12 dB/oct.), 3 (-18 dB/oct.),
4 (-24 dB/oct.)
Turn the Rotary encoder to select the desired
output level.
To store the adjusted contents
1) Press and hold any one of the preset buttons (1
through 6) for at least 2 seconds into which you wish to
store the adjusted contents.
7
For setting another channel, repeat the steps 2 to
5.
After setting, press T.CORR/X-OVER to return to
normal mode.
• Crossover mode is automatically canceled if no operation is
performed within 15 seconds.
3 WAY System
2
Press BAND/TEL. to select desired parameter.
LOW → MID-L → MID-H → HIGH (HI) → LOW
3
Press g or f to select desired cut-off
frequency point (cross over point).
Adjustable frequency bands:
LOW
MID-L
MID-H
HIGH
4
F/R Sub. W
Press SOURCE/POWER to select desired slope.
Adjustable output level: -12 to 0 dB.
6
When setting to “3 WAY ”:
The unit can be operated in a 3 way system.
: 20Hz to 200Hz (in 1/3 octave steps)
: 20Hz to 200Hz (in 1/3 octave steps)
: 20Hz to 20kHz (in 1/3 octave steps)
: 1kHz to 20kHz (in 1/3 octave steps)
Press SOURCE/POWER to select the desired
slope.
Adjustable slope: 0 (FLAT (OFF))*, 1 (-6 dB/oct.),
2 (-12 dB/oct.), 3 (-18 dB/oct.),
4 (-24 dB/oct.)
* FLAT cannot be set for the HIGH slope.
16-EN
3WAY
When setting to “F/R/Sub.W ”:
The unit can be operated in a 2 way system.
• Crossover mode is automatically canceled if no operation is
performed within 15 seconds.
Recalling the Stored Crossover Settings
(CDA-9815/CDA-9813 only)
1
2
3
Press and hold T.CORR/X-OVER for at least 2
seconds.
Press any one of the preset buttons (1 through
6) that has your desired crossover settings in
memory.
Press T.CORR/X-OVER to return to normal mode.
• Crossover mode is automatically canceled if no operation is
performed within 15 seconds.