Download User Manual

(B) 220V : 3-40HP, 440V : 3-75HP (NEMA4 to 20HP)
．JNTMBG
□□□□ JK---
．JNTMBG
□□□□ AZ---
NF B
In stall fa st a ction
fu se
Br akin g Res si tor
MC
Ma in Ckt
Po wer Supp ly
B1 /P
B2
R/L1
U/T1
S/L2
V/T2
W/T3
T/L 3
IM
F acto ry Pr ese t
E
FW D/STOP
1
F WD
(" Close ": FWD)
REV/STOP
2
REV
(" Close ": REV)
Extern al F au lt
3
Eb
Fa ult RESET
4
Mu lti-Ste p
Spee d Re f.1
5
Mu lti-Ste p
Spee d Re d.2
6
Jog ging
7
Acc. & De c.
Switch
8
Ana log
Ou tpu t 1
Ana log
Outp ut 2
(* 2 )
TP2 :
EXTERNAL FREQUENCY
COM MAND
AIN M aste r Sp eed Ref.
TP2 :
SINK
0V ~ 10 V & -1 0V~10 V
, ( 20k Ω)
4 ~ 2 0 m A, (2 50 Ω )
P
IP12
IG1 2
AUX Mu lti-F un ction
An alog Inp ut
DO1
Mu lti-F un ction Out put 1
(Op en Colle ctor 48 V, 50 mA)
0 ~ 1 0V, ( 20k Ω )
GND Analo g sig nal Co mm on
TP1
OPEN
IP12
PUL L UP
PG INPUT
(A PHASE)
R2C
DOG
P
( *1 )
EXTERNAL PG
DC VO LTAGE
M ulti- Fu nctio n Con tact Out put
2 50V AC, <1 A
3 0V DC, < 1A
R1C
SOURCE
+1 2V o r - 12 Po wer Supp ly ( +12 V or -12 V, 20 mA)
fo r Spe ed Ref.
VIN M aste r Sp eed Ref.
0V
GND
R2A
4 ~ 20 mA
0 ~ +1 0V
Anal og M on itor 1, 2
(DC 0 ~ 10 V)
R1B
M ulti-F un ction
Con tact Inp ut
E Shie ld She ath
P
AO2
R1A
2 4V
( So urc e Com m on)
-10 V ~ +1 0V
AO1
RESET
2 4VG
(Sin k Com mo n)
2kΩ
1/2 W
Gr oun ding Le ad
(< 10 0 Ω)
S( +)
S( -)
RS- 485 Por t
A(+ )
A(- )
Shiel d
Shield ed
P
Wire
Twisted Wire
(*1)
Wire or SOURCE type inp ut interface, when setting 1 ~ 8 as si nk typ e
(*2) TheShield
termin
al 1 ~ P8 Shielde
can b eTwisted
set as SINK
Wire
i nput, the short ju mp er of TP2 must be set to SINK position, an d set to SOURCE posi ti on for source type inp ut.
(*2) The terminalc and j can be set as SINK or SOURCE type input interface, when settingc~j as sink type input, the short jumper of TP2
2 4 VG
1
3
5
7
24V VIN AIN AUX DO 1 DOG IP1 2 A(+ ) A( -)
(*3) The
termin
arranposit
gement
must be
set toalSINK
ion, and set toE SOURCE
source
type
2
4 position
6
8for+1
2VG ND
GNDinput.
AO1 AO2 E
IG12 S(+ ) S(-)
R2 A R2C R1 A R1B R1 C
(*1)
(*3) For 220V 25-40HP, 440V 25-75HP inverters, VIN Ref. can be set in two input methods as 0~10V or -10~+10V
(*4) The contro l b oard code No. : 4 P1 01C006000 2
(*4) The terminal A(+), A(-) can be the output terminal of Pulse Input Frequency Command.
(*5) Pulse Input Frequency Command: 50Hz~32KHz, 3~12V High Voltage Level, input resistor 2.7KΩ
3
5
7 24V VIN AIN AUX DO1 DOG IP12 A(+) A(-)
(*6) The terminal arrangement 24VG 1
E
2
6
8 +12V -12V GND AO1 AO2 E IG12 S(+) S(-)
4
R2A R2C R1A R1B R1C
(*7) The control board code No. ：4P101C0060002 (220V 3-20HP, 440V 3-20HP), 4H300D6740006 (220V 25HP, 440V 25-30HP),
4H300D6750001 (220V 30-40HP, 440V 40-75HP)
Fig. 2-b
2-b Standard
Standard connection
connection diagram
diagram
Fig.
1-9