Download Instruction Manual
Transcript
Thank you for choosing CYmodel Global : www.cymodel.com Australia : www.austars-model.com Italia : www.biellaexpress.com FW-190 Item Nr: CY8142B Instruction Manual Before commencing assembly,please read these instructions thoroughly. ALMOST - READY - TO - FLY SAFETY PRECAUTIONS This radio control model is not a toy! lFirst-time builders should seek advice from people having building experience in order to assemble the model correctly and to produce its performance to full extent. lAssemble this kit only in places out of children ,s reach! lTake enough safety precautions prior to operating this model. You are responsible for this model,s assembly and safe operation! lAlways keep this instruction manual ready at hand for quick reference,even after completing the assembly. lCould cause serious injury or even death SPECIFICATION Wing Span: 2120mm (83.5in) 2 Wing Area: 63.8dm (989sq.in) Total Length: 1790 mm (70.5 in) Engine 35-:50cc gas engine Radio : 6 channels ,9 servos REQUIRED FOR OPERATION (Purchase separately) A minimum 6channel radio for airplanes (with 9servos). And dry batteries. 1 ! 5 B Glue A CAUTION: Only use a minimum 6channel radio for airplanes! (No other radio may be used!) Epoxy Glue 6 A minimum 4 channel transmitter for airplanes. required for engine starting ! receiver 12 AA-size Batteries Instant glue Glow engine fuel only. WARNING: Normal gasoline cannot be used with glow engines. remote control For handing the radio properly.refer to its instruction manual. 2 Battery (need 2) 3 Servo(need 9 servos ) 4 Switch (need 2) Fuel Pump 7 8 Engine and Muffler Model A irplane engine:35-50cc gas engine Muffler Silicone Tube Fuel Filter Other equipment for enhancing airplane operation & perormance Ignition Engine Starter 9 Ignition Muffler Plug Wrench 12V Battery (for starter) Purchase a propeller that will match your engine TOOLS REQUIRED ( Purchase separately) Sharp Hobby Knife Phillips Screw Driver Awl Needle Nose Pliers Wire Cutters Scissors BEFORE YOU BEGIN . Read through the manual before you begin ,so you will have an overall idea of what to do. 2 . Check all parts .if you find any defective or missing parts .contact your local dealer. 1 Symbols used throughout this instruction manual,comprise. 3 A B Drill holes with the specified Diameter(here:2mm) Must be purchased separately! Apply instant glue (CA glue,super glue). Ensure smooth non-binding movement while assembling. Pay close attention here! Assemble left and right Sides the same way. Cut off shaded portion. Cut off excess. 2mm ! Warning! 50 2 Apply epoxy glue. C.A L R 2 Do not overlook this symbol. 3 Accessory list for this page. ! 3mm Lock nut 3X16 Screw L 8 8 2.5X85mm rod Install the servo R 4 Rod adjuster Rod adjuster 4 4 HORN 8 2.6X12mm Tp Screw 16 Hinge --------8 Hinge --------4 1 4 Install the aileron L Aileron Install the servo of aileron L R R A B Flap 3mm Lock nut Servo line 3X16 Screw A B 4 4 2.5X85mm rod 2 Make sure hinges are mounted in the same line Aileron Rod adjuster Flap Hinge --------8 2 Rod adjuster 2 HORN A B Hinge --------4 2 Please notice the illustration below when epoxy the pin hinges to the aileron 5 L Bottom view 4 2.6X12mm Tp Screw A B 8 Install the servo of flap R Servo line Tailing edge 3mm A B L 3mm Lock nut R 3X16 Screw 4 4 2.5X85mm rod 2 Aileron Rod adjuster Rod adjuster Warning! Aileron Flap Securely glue together. If coming off during flights,you'll lose control of your airplane which leads to accidents! 2 2 HORN 4 A B 2.6X12mm Tp Screw 3 8 ! Accessory list for this page. 8 Install the missile 9 Install the missile 2mm plywood - - - - -1 8mm nylon Nut -----2 8mm nylon screw -----2 6 Install the missile 50 2 8mm C.A 2mm plywood -------1 7 8mm nylon Nut 8mm nylon screw 8mm -----2 -----2 10 Main wing Install the missile Top view A B Servo line Servo line 4 13 Accessory list for this page. 4X30mm screw -----2 4mm Washer -----1 2 Retainer -----1 -----2 C.A Rod (1.8X80mm) 3X20mm Tp screw -----8 R screw -----2 4mm Lock nut L After glue the PVC cover, cut off its excess part. Rod adjuster -----1 2X8mm Install the main landing gear 50 ! -----1 Air line -----2 11 Main wing.Before installing screw, the tube need to drill a hole 14 Install the main landing gear Ply wood - - - - - - - - - - - -2 3X5mm screw - - - - - - - - - - - -4 4.2mm 4X30mm screw -----2 L 4mm Washer Bottom view -----2 R 15 12 Install the main landing gear Install the main landing gear 4mm Lock nut 3-way pressure inlet -----2 3X20mm Tp screw Strut 3-way pressure inlet Strut -----8 Air inlet 3-way pressure inlet Air tank Quick release connector Quick release connector Switch L Please insure the sealing of the retract system before flight . Pleas notice the inner diameter for each side of the pressure reduction inlet. R 5 Rod adjuster -----1 Retainer 2X8mm Rod (1.8X80mm) screw -----1 -----1 -----1 Air line -----2 ! 18 Main wing Accessory list for this page. 5X45mm screw -----2 5mm Bind nut -----2 5mm Washer A -----2 A -----2 Warning! Hinge Securely glue together ,if coming off during flights. You lose control of your airplane which leads to accidents! --------8 16 A A 8X40mm Carbon tube 19 Main wing Install the elevator L 135 135 R 8mm 8mm A B Make sure hinges are mounted in the same line 8X40mm Carbon tube Hinge --------8 -----2 17 20 Main wing Install the elevator Tailing edge 4mm A B Aileron 5X45mm screw 5mm -----2 5mm Bind nut -----2 Warning! Aileron Securely glue together. If coming off during flights,you'll lose control of your airplane which leads to accidents! 5mm Washer -----2 6 23 Accessory list for this page. ! 3mm Lock nut 4X16mm 4 3X16 Screw Install the elevator, put the servo line into the fuselage screw ----2 4 4mm Washer 2.5X85mm rod 2 --------2 Rod adjuster 2 Rod adjuster 2 HORN 4 2.3X10mm Tp screw 4X16mm screw 4mm Washer Hinge 4 2 Before installing screw, the tube need to drill a hole 4.2mm 2 8 21 Install the servo of elevator 24 Install the rudder A B A B Hinge --------8 A B L 22 L R Make sure hinges are mounted in the same line 25 Install the servo of elevator Horizontal/Vertical tail R D D 3mm Lock nut Servo line 3X16 Screw D 4 4 2.5X60mm rod 2 Rod adjuster Rod adjuster 2 2 HORN Securely glue together ,if coming off during flights. You lose control of your airplane which leads to accidents! 4 A B 2.3X10mm Tp screw 4 7 D ! 28 Accessory list for this page. Install the servo of rudder Rod 2 Aluminium tube 2 Steel wire 2 HORN 2 Rod adjuster 2 3mm Lock nut 2 3X16 Screw 2 Spring 2 A B 26 Install the rudder and tail wheel 29 Install the rudder and tail wheel Rod 2 Aluminium tube 2 Rod adjuster 3mm Lock nut 3X16 Screw 27 6mm nut 6X9 screw Install the engine. Engine:50cc 30 Install the rudder and tail wheel Fuel tank 1 1 M3X20 Tp screw 3 3.2mm Rocker 1 3.2mm Nylon Collar 1 3.2mm Collar 3X3mm Screw Linkage Stopper ----1 2 2mm 3 Nut 3X3mm Screw ----1 8 1.8X350mm Rod ------1 ------1 2 2 2 ! 33 Accessory list for this page. Install the canopy Cut away the surplus pats of canopy care fully along the shaded line. 31 34 Assembly of the full tank Install the canopy After confirming the position(see front of fuel tank). Insert and tighten the screw. Air pressure line Fuel pipe Fuel supply line 3X30mm screw 3mm Washer 32 35 Radio Equipment 3mm rubber band 2.3X10mm Tp screw ----2 - - - - -8 -----2 -----2 Install the cowling Spinner Propeller 3X16mm screw -----5 3mm Bind nut Battery Receiver -----5 3mm Washer 3mm -----5 3mm rubber band Cowling Playwood ----5 A B 6mm Playwood ----5 9 36 38 Adjustment. Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. Adjustment Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. Rudder AILERON 45 Aileron Side view 45 Side view 45 45 Flap 90 Top view 37 Top view 39 Adjustment. Never fly before checking the Cg s required position. In order to obtain the CG specified ,reposition the receiver and battery. Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. ELEVATOR Side view Adjustment. 45 135mm 45 CG Top view ! 10 Warning! NEVER fly the model without well balancing.