Download SMS8RX_Manual_250208..

Proudly Designed in Australia
Narrow Band Wireless Receiver with 2 x Code Hopping Remote Controls For SMS8 Control Panel.
N517
F:\Current_Instructions\Standard Home Alarm\sms8rx[ASTRO28].doc
Description
Product Description & Features
Remote Control Function
Master Default Setting
Programming Remote Controls
Programming Wireless Detectors
Wireless Detector Supervision
Wireless Detector Low Battery & Tamper Warning
Page
1
2
3
4
5
6
6
Your SMS8RX is a state- of- the-art narrow band wireless receiver, designed to operate with
the SMS8RX most alarm control panels.
Main Features include:
Simple Installation.
Code Hopping Remote Control Technology (remotes can not be copied by scanning or
code grabbing).
Remote Functions include Arm/Disarm, Home Arm & Panic.
Ability to quickly add or erase detectors from your system.
8 Wireless Detector Zones Available.
Wireless Detector Supervision
Low Battery Warning
Detector Tamper Warning
Intelligent Detector Learning Program to prevent accidental code duplication.
Memory Recall Function to identify individual detectors sending low battery or tamper
codes.
Wireless Detectors available include PIR's, Internal or External Reed Switches &
Smoke Sensors
1
DISARMING: Pressing the button 1 once. This will
disarm the system from away and stay mode.
2
3
1
AWAY ARMING: Press the button 2 to arm the
system in AWAY mode. The system will arm instantly
even if a delay is programmed on the panel.
STAY ARMING: Press the button 3. This will arm
the system in STAY mode and the exit delay applies.
PANIC: Press and hold the button 2 and 3 together
to activate panic.
LED'S
Receive
Red
Valid
Red
Program
Yellow
Run
Green
Receive: On when any data packets are received - even
if codes are not programmed.
Valid: On while valid data is decoded e.g. while Tx is
pressed or PIR transmitting. Flashes 6 times when in
program mode and valid data is received for storage.
Program: On when any switch is in the “on” position,
flashes when more than one switch is in the on position.
Run: Normally flashing at 0.5 Hz - indicates
microprocessor is running.
Antenna
Wire
Add
Delete
ON
1 2 3 4 5 6 7 8
8 8
Bank 1
The SMS8 Panel
must have the
latest software
version. You can
identify this by
reading the letters
RF on one of the
main chips on the
SMS8 Panel.
+12VDC
Ground
+ BUS
- BUS
OFF
Keep the antenna vertical &
straight, and away from
metal. Mount the receiver
inside the top of your panel
box, with the maximum
possible length of antenna
extending from the top.
For normal operation ensure that all dipswitches are down (off) after programming. If the
switches are not down it may cause the unit to respond incorrectly.
2
After connecting your SMS8RX to your panel as per the connection diagram on
page 2,
Carry out the default procedure outlined below.
You can default your SMS8RX in case you make a mistake, or are unsure of your receiver setup.
"Defaulting" your receiver will cause all detector & remote codes to be erased.
To default your receiver, follow these steps:
1. Set all dipswitches on Bank 1 to ON.
ON
1
2
3
4
5
6
7 8
OFF
Bank 1
2. Press & Hold the delete button for 3 seconds.
Delete
3 seconds press
3. All LED's on the receiver stop flashing to confirm that the receiver has been defaulted.
4. Return all dip switches back to the OFF position.
In ‘zone programming’ (option sub-menu 2) ‘enable’ or turn on each wireless zone as
an ‘RF Zone’.
Also you can program to enable or disable the ‘RF remote’ and ‘RF tamper’ in the
menu ‘control timers’ (option sub-menu 4).
PLEASE ENSURE THE PANEL IS PROGRAMMED TO ENABLE EACH RF
FEATURE as described above.
IF YOU ENCOUNTER ANY PROBLEMS WITH YOUR SMS8RX, OR REQUIRE
ADDITIONAL TECHNICAL INFORMATION NOT CONTAINED IN THIS MANUAL,
PLEASE CONTACT YOUR RHINO DEALER.
3
TO ADD A REMOTE CONTROL
1. On Bank 1, set dipswitch number 7 and 8 to ON. The yellow Program LED will come on.
ON
1
2
3
4
5
6
77 8
NOTE WHEN
PROGRAMMING REMOTES
& WIRELESS DETECTORS:
OFF
Bank 1
2. Press & Hold the button on your remote
3. Press the Add Button. The red Valid LED will start flashing at 0.5Hz.
Add
…
Due
to
the
excellent
performance of the receiver,
you are likely to "swamp" the
receiver with too much RF
signal if you transmit within 5
metres of the receiver. To
prevent this from occurring,
simply remove the antenna
from your receiver whilst
programming. You will now
have to be within approx 1m of
the
receiver
whilst
programming.
4. Now release the button on the remote. The red valid light will turn off.
ACOM
5. Repeat steps 2 - 4 for any extra remotes that you wish to add. Maximum of 5 can be used.
6. Return dip switches 7 & 8 to the OFF position. The yellow program light will turn off.
NOTE: if the unit is wired to the panel via the BUS connections the system will now arm and
disarm etc.
TO DELETE ALL REMOTE CONTROLS
1. On Bank 1, set dipswitch Number 7 & 8 to ON. The yellow Program LED will come on. (If the LED
flashes, check that, you don't have more than one dipswitch set to on).
ON
1
2
3
4
5
6
7 8
Bank 1
2. Press the Delete Button.
Delete
OFF
!
IMPORTANT
When programming,
make sure that no
detectors are
transmitting, as they
will interfere with your
programming
procedure.
3. All remote controls will now have been erased from the memory of
the receiver.
4. Return dip switches 7 & 8 to the OFF position. The yellow Program light will turn off.
IMPORTANT NOTE: When installing any wireless device,
make sure that it is at least 5 METRES AWAY from the receiver.
4
Wireless PIR, Wireless Reed Switch, Wireless Smoke Sensor)
TO ADD A DETECTOR
1. On Bank 1, select the Zone (1-8) that you wish to program a detector into. The yellow Program
ON
E.g. programming a detector into Zone 1
1
2
3
4
5
6
7 8
OFF
Bank 1
LED will come on. (If the LED flashes, check that, you don't have more than one dipswitch set to
on).
Note: Learning a new detector into a zone which already had a detector learnt into that zone, will
erase the original detector's code & replace it with the new detector's code. Furthermore, if that
detector code has previously been learnt into another zone, the receiver will determine this as being
an error, and will automatically delete the code duplication by erasing the code from the other zone.
2. Press the Add Button. The red Valid LED will start flashing at 0.5Hz.
Add
…
3. Now trigger the sensor. The valid light will stop flashing once the detector has been successfully
programmed.
4. Return all dip switches back to the OFF position. The yellow program light will turn off.
TO DELETE A DETECTOR
!
1. On Bank 1, select the Zone (1-8) that you wish to delete a sensor from. The yellow Program LED
will come on. (If the LED flashes, check that, you don't have more than one dipswitch set to on).
ON
E.g. deleting a detector from Zone 1
1
2
3
4
5
6
7 8
OFF
Bank 1
2. Press the Delete Button.
Delete
3. The detector will now have been erased from the receiver's memory. You can test this by
triggering the detector, and watching that the Valid LED no longer illuminates on your receiver
when the detector transmits, and also by watching that the system no longer is triggered by that
detector.
4. Return all dip switches back to the OFF position. The yellow program light will turn off.
5
All of your individual wireless detectors (i.e. Wireless PIR, Wireless Reed, or Wireless Smoke
Detectors) can send a supervision report to your receiver to confirm that they are fully functional.
Supervision is always enabled, the receiver will be expecting to receive the individual supervision
code from each detector approximately every 2.4 hours i.e. at least 10 reports per day, per detector.
The SMS8RX only requires one report from each detector during the 24 hour period to satisfy the
supervision criteria. An extra 9 reports are still given to ensure that the supervision report is received.
If all 10 supervision reports are missed from one detector during the 24 hour time frame, then the
SMS8 keypad will display “SERVICE”. You then access the service menu and it will advise of a
‘Supervision’ failure on the particular zone.
Low battery signals will only be fixed by opening the detector to send a tamper signal to the
SMS8RX. Replace the old batteries with new ones and replace the detector cover.
Supervision signals will only be fixed by fixing the particular detector so that is able to transmit to the
SMS8RX.
Tamper and Zone alarms open the particular zone for 1 second. A restore will be sent 1 second after
the detector sends the trigger signal.
Your detectors will automatically transmit a low battery report to your SMS8RX receiver when the
batteries are nearly flat.
The low battery report code is also transmitted after the alarm code, every time a detector is
triggered.
After the individual detector has sent a low battery, the SMS8RX will display a ‘service’
message. After accessing the service menu it will display a ‘supervision’ fault for the particular
zone with a low battery. Please note: Your SMS8RX identifies a different low battery code for
each individual detector. When you replace the batteries, your receiver will automatically see that
the low battery code is no longer being sent from that detector.
The tamper signal will display “SERVICE” on the SMS8 Keypad whenever the front case is
removed and the tamper switch is released on a Wireless PIR Detector or Wireless Reed Switch.
6
This page intentionally blank.
7
8