Download ceiling mounted cassette type
Transcript
PCSPH1411 Ask a installer or contractor to install this product. Do not try to install the product by yourself. Improper installation can result in water or refrigerant leakage, electrical shock, or explosion. Warning Use only those parts and accessories supplied or by Daikin. Ask a installer or contractor to install those parts and accessories. Use of unauthorised parts and accessories or improper installation of parts and accessories can result in water or refrigerant leakage, electrical or explosion. shock, Read the User's Manual carefully before using this product. The User's Manual provides important safety instructions and warnings. Be sure to follow these instructions and warnings. If you have any enquiries, please contact your local importer, distributor and/or retailer. Cautions on product corrosion 1. Air conditioners should not be installed in areas where corrosive gases, such as acid gas or alkaline gas, are produced. 2. If the outdoor unit is to be installed close to the sea shore, direct exposure to the sea breeze should be avoided. If you need to install the outdoor unit close to the sea shore, contact your local distributor. Dealer: 2nd Floor, Hanston Square, 17 San Miguel Avenue, Ortigas Center, Pasig City, 1605 Tel. No.: (02) 942-6800/942-6792 Fax No.: (02) 942-6793 out notice. c All rights reserved 02/14 SS Daikin meets your needs with this full lineup of inverters for various types of indoor units and power supplies. 2HP 50 Series CEILING MOUNTED CASSETTE TYPE NEW 2.5HP 60 3HP 71 4HP 100 NEW 5HP 125 NEW 6HP 140 NEW Round Flow FCQ50KVEA Indoor unit FCQ60KVEA CEILING SUSPENDED TYPE FCQ71KVEA NEW NEW FHQ71CAVEB Indoor unit WALL MOUNTED TYPE NEW FCQ140KVEA NEW FHQ125CAVEB FHQ100CAVEB FHQ140CAVEB NEW Pair NEW FCQ125KVEA FCQ100KVEA FAQ71CVEA Indoor unit 1 Phase, 220–230 V DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE NEW FLOOR STANDING TYPE NEW Simultaneous Twin Multi Indoor unit NEW NEW FBQ50DAVET Indoor unit FAQ100CVEA FBQ60DAVET NEW FVQ50CVE FBQ71DAVET NEW FVQ60CVE FBQ125DAVET FBQ100DAVET NEW FVQ71CVEB NEW NEW FVQ100CVEB NEW FVQ125CVEB NEW CEILING MOUNTED CASSETTE TYPE FBQ140DAVET FVQ140CVEB NEW Round Flow FCQ60KVEAX2 Indoor unit NEW DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE FCQ71KVEAX2 NEW FBQ60DAVETX2 Indoor unit NEW FLOOR STANDING TYPE NEW FVQ60CVEX2 Indoor unit FBQ71DAVETX2 FVQ71CVEBX2 OUTDOOR UNIT 1 Phase, 220–230 V Outdoor unit RZR50LVVM RZR60LVVM RZR100LVVM RZR125LVVM RZR140LVVM FCQ100KVLT FCQ125KAVLT FCQ140KAVLT Indoor unit FBQ100DAVET FBQ125DAVET FBQ140DAVET 3 Phase, 220 V Outdoor unit RZQ100KCTLT RZQ125KCTLT RZQ140KCTLT 3 Phase, 380 V Outdoor unit RZQ100LUYLT RZQ125LUYLT RZQ140LUYLT RZR71LVVM NEW CEILING MOUNTED CASSETTE TYPE 1 Pair 3 Phase, 220V/380 V Round Flow Indoor unit DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE NEW OUTDOOR UNIT 2 Full Lineup of Inverter Series Daikin meets your needs with this full lineup of inverters for various types of indoor units and power supplies. 100 125 4 Pair CEILING SUSPENDED TYPE 3 WALL MOUNTED TYPE FLOOR STANDING TYPE 1 CEILING MOUNTED CASSETTE TYPE Round Flow Twin 3.40 2.85 2 DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE 3.60 3.57 Cooling* CEILING MOUNTED CASSETTE TYPE Round Flow 1 Phase, 220–230 V 4.30 140 FCQ50KVEA RZR50LVVM DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE FCQ60KVEA RZR60LVVM Cooling* 71 Cooling* 60 4.83 : Continuous Cooling* 50 COP Cooling* 34 new combinations added! Achieved higher COP Cooling* : New Lineup Energy saving CEILING MOUNTED CASSETTE TYPE Round Flow Note : *Rated cooling capacities are based on the following conditions: Indoor temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24.0°CWB. Equiv. refrigeration piping, 7.5 m (horizontal). DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE Comfortable CEILING MOUNTED CASSETTE TYPE Round Flow DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE Enhanced comfort with Inverter Simultaneous Twin Multi Operation Comfortable currents of air are sent to every corner of the room. For example, four indoor units are judiciously spaced in this wide single-floor restaurant to deliver comfortable currents of air to every corner of the room. Inverter performs variable control of frequency, which determines air conditioner’s power performance. At startup, full power is used to achieve the set temperature quickly. Then, the capacity is adjusted according to the outdoor temperature changes and subtle indoor load changes to achieve fine capacity control resulting in a more stable room temperature. Non-inverter type air conditioners must be switched on and off repeatedly, causing large fluctuations of the room temperature. At startup, inverter raises frequency smoothly, eliminating the starting current spike. Non-inverter Current Pair Pair 3 Phase, 220 V COP is equal to capacity (kW) divided by power consumption (kW), and the larger the COP value, the higher the energy efficiency, enabling cooling and heating with less electricity and increasing the energy saving performance. 3 Phase, 380 V Round Flow (1 Phase, 220–230 V) FCQ71KVEA FCQ100KVEA FCQ125KVEA FCQ140KVEA RZR71LVVM RZR100LVVM RZR125LVVM RZR140LVVM What is COP (Coefficient of Performance) FLOOR STANDING TYPE CEILING MOUNTED CASSETTE TYPE Cooling operation Temp Starting current Running current Inverter Cools a room in less time Refrigerant branch piping kit for Twin Multi operation Time Current Set temp Small temp. difference Time Inverter power control Non-inverter type air conditioner Running current Time 2 sets of Twin Multi 3 4 CEILING MOUNTED CASSETTE TYPE Round Flow Cassette air conditioner with 360° uniform airflow sets the standard Avoids uneven temperature and discomfort caused by drafts. Comfort enhanced by Round Flow! FCQ50/60/71/100/125/140K 360° airflow Air movement is gentle with Round Flow With uniform temperature distribution Enhanced Comfort 360° airflow can maintain comfort even if air discharge speed is lower. Airflow distribution Creates uniform comfort throughout the space If you raise the set temperature by 1 to 1.5°C,and velocity is decreased by 25%, you still obtain the same feeling temperature and comfort. Greater comfort Improved energy saving Option Accessory required for indoor unit Navigation Remote Controller Adapts easily to the installation space. (Wired Remote Controller) Because air flows out from corner outlets, comfort spreads more widely. BRC1E62 Typical flow patterns Note: Remote controller cable not included. Cables must be procured locally. Wireless LCD remote controller A signal receiver must be added to the indoor unit. There are a total of 23 flow patterns. All-round flow 3-way flow (E.g., installed in middle of ceiling) (E.g., installed near a wall) L-shaped 2-way flow (E.g., installed in a corner) Opposite 2-way flow (E.g., installed in a long room) 4-way flow also possible. BRC7F633F Note: Whatever the discharge direction, the same type of panel is used. If installing for other than all-round flow, an air discharge outlet sealing material (option) must be used to close each unused outlet. Operation sound increases when using 2-way or 3-way flow. Signal receiver unit (Installed type) Grime prevention and bactericidal coating: Make cleaning easier. Wireless remote controller and signal receiver unit are sold as a set. External panels are treated with a coating that Treated Untreated repels dirt. surface surface Features *1Applicable when wired remote controller is used *2For the outdoor units *3Applicable when BRC1E62 is used *4Applicable when BRC1C61 is used 5 • • • *2 • • • *2 • • • • • • • • • • • • Others Anti corrosion treated heat exchangers Ultra long-life filter Fresh air intake kit High-efficiency filter Options DIII-NET communication standard Interlock control Central remote control Control by 2 remote controllers Group control by 1 remote controller External command control Auto-restart Self-diagnosis function Control features Emergency operation Low gas pressure detection *4 Ceiling soiling prevention *3 Filter sign On/Off timer *3 Long-life filter Off timer (programmed) *3 Pre charged for up to 30 m Weekly schedule timer *3 Drain pump mechanism Setpoint range set *2 Silver ion anti-bacterial drain pan Setpoint auto reset *1 Work & Servicing Cleanliness Anti-bacterial air filter Night quiet operation • • • • • Remote controller Two selectable temperature-sensors High ceiling application Programme "Dry" Switchable fan speed (2 step) Swing pattern selection Auto swing Comfort *2 To prevent dirt sticking to the external panels, they have been coated with a surface treatment. Resists soiling Grimy surface • Condition after exposure to the smoke of 600 cigarettes in 1 m3 enclosed space. Silver ion anti-bacterial drain pan Non-flocking flaps Filter has anti-mould and bactericidal treatment Mould-proof drain pan includes a silver ion antibacterial agent that assists in preventing the growth of slime, bacteria, and mould that cause smells and clogging. Condensation does not easily form on and dirt does not cling to non-flocking flaps. It is easy to clean. Prevents mould and microorganisms growing out of the dust and moisture that adheres to the filters. 6 CEILING MOUNTED CASSETTE TYPE Fine square panels Compact body and quiet operation mm 95 0m Indoor unit High Low 50K 60K 71K 100K 125K 140K 35 35 35 43 44 44 28 28 28 32 34 36 Same for all models m Optimal comfort and convenience assured by air discharge modes Note: Air direction is set to the standard position when the unit is shipped from the factory. The position can be changed from the remote controller. Air direction Standard setting Setting to prevent soiling of ceiling* Desired situation Standard position to prevent draft. Recommended for shops with light coloured ceilings that must be kept spotless. Note : Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions. Quick and easy to install 5-levels air direction setting Auto-swing between 15° and 60° Auto-swing between 25° and 60° Settable to 5 different levels between 25° and 60° Settable to 5 different levels between 15° and 60° The air direction is set automatically to the memorised position of the previous air direction. Auto air direction control *Closing of the corner discharge outlets is recommended. Suitable for high ceilings Even in spaces with high ceilings, a comfortable airflow is carried down to the floor level. Criteria for ceiling height and number of air discharge outlets (Ceiling height is reference value) Number of air discharge outlets used Standard Ceiling High ceiling height High ceiling 50K–71K 100K–140K All round 4-way 3-way 2-way flow flow flow flow All round 4-way 3-way 2-way flow flow flow flow 2.7 m 3.1 m 3.0 m 3.5 m 3.0 m 3.4 m 3.3 m 3.8 m 3.5 m 4.0 m 3.5 m - 3.2 m 3.4 m 3.6 m 4.2 m 3.6 m 3.9 m 4.0 m 4.2 m 4.2 m 4.5 m 4.2 m - The condition of the drain pan and drain water can be checked by removing the drain plug and intake grille. 256 mm *1 266 mm *2 Easy height adjustment Each corner of the unit has an Adjuster Pocket that lets you easily adjust the unit's suspended height. Note: If the wireless remote control option is installed, a light receptor unit is housed in one of the adjuster pockets. All models can be installed without using lifter because of the light weight. Installable in any direction Since the orientation of the intake grill can be adjusted after installing, the direction of the intake grill lines can be unified when multiple units are installed. Drain pump is equipped as standard accessory with 850 mm lift. Both indoor unit and wired remote controller (option (BRC1D61,BRC1E62) ) contain temperature- sensors. Temperature sensing can be set at the unit or, to further improve comfort level, closer to the target area at the wired remote control. This feature must be set during commissioning by the technicians. *Temperature-sensor on indoor unit must be used when the air conditioner is controlled from another room. **Wireless remote controller does not have a temperature-sensor. Switchable fan speed: High/Low High setting provides maximum reach while low setting minimises drafts. On/Off timer Operation starts when the preset time of the ON timer elapses and stops when the preset time of the OFF timer elapses. 7 Drain plug Options required for specific operating environments Ultra long-life filter Panel spacer Even in smoky environments where the air conditioning is on most of the time, the ultra long-life filter only has to be changed once a year. Use when only minimal space is available between drop ceilings and ceiling slabs. Smoky atmosphere: annual filter change *For dust concentration of 0.3 mg/m3 (Requires separately sold Air Cleaner.) 1 year (Approx. 5,000 hr) 15 hr/day x 28 day/month x 12 month/year 40mm Ordinary store or office: filter change every 4 years Panel spacer *For dust concentration of 0.15 mg/m3 4 years (Approx. 10,000 hr) 8 hr/day x 25 day/month x 4 years Note: Some ceiling constructions may hinder installation. Contact your Daikin Dealer before installing your unit. High-efficiency filter Available in two types: 65% and 90% colorimetry. Sealing material of air discharge outlet Fresh air intake kit Using this kit, a duct can be fitted to increase the intake of outdoor air. Outside A round duct can be attached without the need for a chamber. Chamber type (without T-joint pipe and fan) 850 mm 175 mm Because the drain socket is transparent, after the drain piping has been installed, it is easy to check if the drain come out through the socket. A flanged port for direct connection of a round duct is provided. An existing branch duct chamber can also be fitted (square slit hole). The units can be installed in the following different ways. Chamber type (with T-joint pipe and without fan) KDDP55B160 Transparent drain socket Sealing material block air discharge openings not used in 2-way or 3-way blow. Branch duct (direct-connection round duct) Note: *Connecting ducts, insect nets, fire dampers, air filters, and other parts should, as required, be procured locally. **Outside Air fan interlocked with air conditioning unit is necessary. Optional PCB(KRP1C63)is required for interlocking. ***It is recommended that the volume of outdoor air introduced through the kit is limited to 10% of the maximum airflow rate of the indoor unit. Introducing higher quantities will increase the operating sound and may also influence temperature sending. Note: Factory settings are for standard ceiling height and all-round flow. High ceiling settings (1) and (2) are set with the remote controller by field setting. Two selectable temperature-sensors e en th ! p o t e Jus ke grill inta With Ultra long-life filters (option), maintenance is not required in normal shops or offices for up to four years. Just 256 mm high. Installable in tight ceiling spaces (50K-71K) *1 298 mm high with 100K–140K *2 308 mm high with 100K–140K Auto-swing Easier to maintain dB(A) Panel size is same for all models, FCQ50-140K. It is easy to maintain a neat appearance when multiple units are installed. 950 Round Flow KDDP55B160K Flexible duct (procured locally) Flexible duct T-joint pipe (procured locally) T-joint pipe Suction chamber Intake duct Connection (procured locally) chamber (duct length: 4 m max.) Suction chamber Intake duct Connection (procured locally) chamber (duct length: 4 m max.) Direct installation type KDDP55X160 Duct flange (with insulation material) Intake duct (procured locally) Note: Use of options will increase operating sound. Connection to a centralised control system is available without option Low gas pressure detection 8 CEILING SUSPENDED TYPE Comfortable airflow travels throughout the room NEW The latest stylish model Sophisticated design Flexible installation The unit fits more snugly into tight spaces. Flap neatly closes when not in use. FHQ71/100/125/140CA Installation flexibility for freedom of design 30 mm 30 mm or more or more *Water used in the test-run can now be drained from the air discharge opening rather than from the side as was formerly the case. Fresh white colour. Drain pump kit (option) can be easily incorporated Drain pipe connection can be done inside the unit. refrigerant and drain pipe outlets are at the same opening. Comfortable The technology of the DC fan motor, wide sirocco fan, and large heat exchanger combine for greater airflow and quiet operation. High/Middle/Low : 46/42/38 db(A) Auto swing (up and down) and louvers (left and right by hand) bring comfort to the room Option Accessory required for indoor unit Navigation Remote Controller BRC1E62 Drain pump kit (built inside main unit) Connection to a centralised control system is available, without option. All wiring and internal servicing can be done from under the unit Pipes more easily rigged Easy maintenance Installable on ceilings 4.3 m high Note: Remote controller cable not included. Cables must be procured locally. mm Low gas pressure detection Louver manually adjusts for straight or wide angle airflow (Wired Remote Controller) 600 Long-life filter lasts up to 6 months* * For dust concentration of 0.15 mg/m3 Two time settings (2500 hrs and 1250 hrs) are available to match the installation environment. Maintenance time warning is displayed on the remote controller (filter sign). Two selectable temperature-sensors Wireless LCD remote controller Both indoor unit and wired remote controller (option (BRC1E62) ) contain temperature- sensors. Temperature sensing can be set at the unit or, to further improve comfort level, closer to the target area at the wired remote control. This feature requires initial setting by the installer. A signal receiver must be added to the indoor unit. BRC7GA56 *Temperature-sensor on indoor unit must be used when the air conditioner is controlled from another room. **Wireless remote controller does not have a temperature-sensor. Wireless remote controller and signal receiver unit are sold as a set. ("Auto" is applicable when BRC1E62 is used.) Easy-clean, flat surfaces Programme "Dry" Features 9 • • *3 • • • • • • • • • • Anti corrosion treated heat exchangers Fresh air intake kit DIII-NET communication standard Options Others Interlock control Central remote control External command control *3 Group control by 1 remote controller *5 Control by 2 remote controllers *4 Auto-restart Off timer (programmed) *4 Control features Self-diagnosis function Weekly schedule timer *4 Emergency operation Setpoint range set *4 Low gas pressure detection Setpoint auto reset *3 Filter sign Night quiet operation *2 Pre charged for up to 30 m Two selectable temperature-sensors *1 Work & Servicing Drain pump mechanism High ceiling application Programme "Dry" Switchable fan speed (3 step) Auto swing • • • *1Installable on max. 4.3 m high ceiling *2Applicable when wired remote controller is used *3For the outdoor units *4Applicable when BRC1E62 is used *5Option Anti-bacterial air filter Remote controller Cleanliness Comfort Non-flocking flap Condensation does not easily form on and dirt does not cling to non-flocking flap. Non-flocking flap It is easy to clean. Switchable fan speed: High/Middle/Low and Auto Signal receiver unit (Installed type) Drain pump kit (option) includes a silver ion antibacterial agent that assists in preventing the growth of slime, bacteria, and mould that cause smells and clogging. *3 Dehumidification is a microprocessor controlled to prevent abrupt and uncomfortable changes in air temperature. Oil resistant grille Quiet operation Oil-resistant plastic is used for the air suction grille. This satisfies durability in restaurants and other similar environments. dB(A) Indoor unit High Middle Low 71CA 38 42 44 46 36 38 41 42 34 34 37 38 100CA 125CA 140CA Note : Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions. Note: Intended for use in salons, dining rooms, and ordinary sales floors, this specification is not suitable for kitchens or other harsh environments. 10 WALL MOUNTED TYPE Compact design and easy installation NEW Easy installing and servicing Compact & Sophisticated design FAQ100 FAQ71/100C 9kg lighter 340 mm FAQ71C 1,200mm 370mm shorter FAQ100BV FAQ100C Height 360mm 340mm Width 1,570mm 1,200mm Depth 200mm 240mm Weight 26kg 17kg Left pipe Back-left pipe Bottom-left pipe Back-right pipe Right pipe Bottom-right pipe Maintenance possible from the front of the unit Flaps neatly close when not in use FAQ100C 6-direction piping offers greater installation flexibility. All maintenance tasks can be carried out via front access. During service work, attachment and detachment of parts is easier. Drain pump kit is available as option. Installs onto side of unit. Comfortable Option Accessory required for indoor unit Auto swing (up and down) and wide-angle louvers (left and right by hand) facilitate even room temperature Navigation Remote Controller (Wired Remote Controller) BRC1E62 Note: Remote controller cable not included. Cables must be procured locally. An air discharge modes ensure comfortable air distribution across the entire room Wireless LCD remote controller A signal receiver must be added to the indoor unit. Height of drain up Refrigerant piping 1,000 mm Wide-angle louvers (by hand) Drain pump kit Drain pump kit can be installed on either left and right side of the air conditioner. Soft material louver bends airflow over a wider area Auto-swing 5-level air direction setting Gettable to 5 different levels BRC7EB519 Comfort even on the far side of the room Wireless remote controller and signal receiver unit are sold as a set. • • *3 • • • • • • • • • Anti corrosion treated heat exchangers DIII-NET communication standard Others Interlock control Central remote control External command control Group control by 1 remote controller *3 Control by 2 remote controllers *5 Auto-restart *4 Control features Self-diagnosis function *1 Emergency operation *1 Low gas pressure detection On/Off timer *1 Filter sign Off timer (programmed) *1 Pre charged for up to 30 m Weekly schedule timer *3 Drain pump mechanism Setpoint range set *2 Mould-proof air filter Setpoint auto reset • • *1Applicable when BRC1E62 is used *2Applicable when wired remote controller is used *3For the outdoor units *4Applicable when BRC1C61 is used *5Option Work & Servicing Cleanliness Night quiet operation Programme "Dry" Remote controller Two selectable temperature-sensors *1 High fan speed mode Auto airflow rate Switchable fan speed (3 step) Comfort Auto swing Easy cleaning Removable and washable grille Flat panel, easy to wipe dust off Features 11 Connection to a centralised control system is available without option To carry air to the far side of long rooms, extra-high airflow adds 10% more fan speed the "high" setting. Air discharge strength is selected from the remote controller by field setting. Signal receiver unit (Installed type) • • Indoor unit Two selectable temperature-sensors Switchable fan speed: High/Middle/Low Non-flocking flaps Condensation does not easily form on and dirt does not cling to non-flocking flaps. It is easy to clean. Auto airflow rate (When BRC1E62 is used) *3 Programme "Dry" Dehumidification is microprocessor controlled to prevent abrupt and uncomfortable changes in air temperature. 12 DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE Enhance comfort using cleverly placed ducts Increased freedom of design thanks to variable control over external static pressure FBQ50/60/71/100/125/140DA Comfort airflow achieved in accordance with conditions such as duct length. Using a DC fan motor, the external static pressure can be controlled within a range of 50 Pa to 200 Pa. When testing standard integrated ceiling units that employ duct work, much time used to be required to adjust airflow to the right level. Thanks to the ability provided by Daikin to automatically perform this troublesome adjustment using a remote controller, this step is now quick and easy. (Adjust by H tap .) 1. Adjust to approximately ±10% of the rated H tap airflow. 2. Once actual operation has begun, adjustment of the rated airflow is not possible. Easier connection with the centralised control system dB(A) 200 Pa Set to low static pressure when ducts are short. Option Use remote controller to adjust airflow Quiet operation Freely control external static pressure 50 Pa Reduced installation time Set to high static pressure for advanced needs such as when using dampers and long ducts. High Low 50/60/71DA 37 32 100DA 38 33 125/140DA 40 36 Note : Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions. Accessory required for indoor unit Easy maintenance Navigation Remote Controller (Wired Remote Controller) Thin, lightweight indoor unit makes delivery and installation easy. BRC1E62 Note: Remote controller cable not included. Cables must be procured locally. With a height of only 300 mm, installation is possible even in buildings with narrow ceiling spaces. Wireless LCD remote controller Clean Silver ion anti-bacterial drain pan Mould-proof drain pan includes a silver ion antibacterial agent that assists in preventing the growth of slime, bacteria, and mould that cause smells and clogging. Comfortable A signal receiver must be added to the indoor unit. 300mm BRC4C64 Maintenance is easy because the drain pan can be removed. Two selectable temperature-sensors Signal receiver unit (Separate type) Indoor unit 50/60/71DA Height (mm) Wireless remote controller and signal receiver unit are sold as a set. Width (mm) Depth (mm) Machine weight (kg) 100DA 125/140DA 300 1,000 1,400 700 36 Both indoor unit and wired remote controller (option) contain temperature- sensors. Temperature sensing can be set at the unit or, to further improve comfort level, closer to the target area at the wired remote control. This feature requires initial setting by the installer. *Temperature-sensor on indoor unit must be used when the air conditioner is controlled from another room. **Wireless remote controller does not have a temperature-sensor. 46 Emergency operation Self-diagnosis function Auto-restart Control by 2 remote controllers Group control by 1 remote controller External command control Central remote control Interlock control DIII-NET communication standard High efficiency filter Anti corrosion treated heat exchangers *2 *3 *3 *3 *4 *5 • *2 *5 • Low gas pressure detection • *3 Filter sign • *2 Long-life filter • Anti-bacterial air filter • On/Off timer • Off timer (programmed) • Weekly schedule timer • Setpoint range set • Setpoint auto reset • *1 *1Applicable when wired remote controller is used *2For the outdoor units *3Applicable when BRC1E62 is used *4Applicable when BRC1C61 is used *5Option 13 • Night quiet operation Programme "Dry" • Work & Servicing Two selectable temperature-sensors Switchable fan speed (2 step) • Cleanliness Pre charged for up to 30 m Remote controller Comfort Silver ion anti-bacterial drain pan Features *2 Control features Option Others Simultaneous air conditioning of two rooms and ventilation grille (ventilation opening) When air conditioning two rooms simultaneously, the air discharged into each room must be circulated back to the air conditioner. To achieve this, a ventilation duct should be installed for each room or one of the indicated ventilation grilles should be installed on the partitioning wall or under the door between the rooms. Door-installed ventilation grille Partitioning wall Wall-installed ventilation grille Under-door cutout Ventilates air through the partitioning wall. (See right) Ventilation grille Ventilation grille Under-door cutout Note: The under-door cutout method should be used only when there is a small volume of airflow. 14 Floor Standing Type New airflow control for more comfort New comfortable airflow control 1) Left and right directions (by remote controller) Auto swing direction is selectable from 3 patterns to suit the layout of the room. Pattern 1 Wide swing toward the front Pattern 2 Swing on the left side Pattern 3 Swing on the right side FVQ50/60/71/100/125/140C NEW When installed in the center of a wall. When installed in the corner of a room. 2) Up and down directions (by hand) Independent up-and-down airflow directions facilitate even room temperature and help save energy. Freely select both up and down airflow direction with 8-louver (horizontal blade) operation. BRC1E62 can be incorporated into the main unit. Example applications New unit Upper louver (1) Lower interlocking louvers (2) Lower louver (1) Each set of louvers to can be independently adjusted. (Manual adjustment) Comfortable fan speed control Option Switchable fan speed: High/Middle/Low and Auto Accessory required for indoor unit ("Auto" is applicable when BRC1E62 is used.) Navigation Remote Controller Airflow rate is automatically controlled in accordance with the difference between room temperature and set temperature. High fan speed mode (applicable for FVQ50-100) Note: Remote controller cable not included. Cables must be procured locally. To carry airflow to the far side of the room, airflow rate can be increased 5% or 10% depending on the installation condition or customer's request. (Field setting by remote controller.) Programme "Dry" Dehumidification is microprocessor controlled to prevent abrupt and uncomfortable changes in air temperature. Features *1Applicable when BRC1E62 is used *2Applicable for FVQ50-100 *3For the outdoor units *4Applicable when BRC1C61 is used 15 • *3 • • *3 • • • • • • • • • Anti corrosion treated heat exchangers DIII-NET communication standard Others Interlock control Central remote control External command control Group control by 1 remote controller Control by 2 remote controllers Auto-restart Control features Self-diagnosis function *4 Emergency operation *1 Low gas pressure detection On/Off timer *1 Filter sign Off timer (programmed) *1 Long-life filter Weekly schedule timer *1 Pre charged for up to 30 m Setpoint range set *3 Anti-bacterial air filter Setpoint auto reset • • Night quiet operation *2 Two selectable temperature-sensors High fan speed mode *1 Programme "Dry" Auto airflow rate Switchable fan speed (3 step) Independent up-and-down airflow Auto swing • • • Work & Servicing Cleanliness Quiet operation dB(A) Indoor unit 50/60/71C 100C 125C 140C High 43 50 51 53 Middle 41 47 48 51 Low 38 44 46 48 Auto airflow rate is selectable. BRC1E62 Remote controller Turning louvers and upward and leaving and horizontal will reduce uneven room temperature. Note : Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions. (Wired Remote Controller) Comfort When cooling Upper interlocking louvers (4) Energy saving A DC fan motor improves efficiency. Quick and easy installation and maintenance Lightweight indoor unit Enables smooth transport and installation of the indoor unit. Indoor unit 50/60/71C Weight 39 100C 125C (kg) 140C 47 Long-life filter lasts about 1year * maintenance not required * For dust concentration of 0.15 mg/ m3 Employs a safety lock function of suction grill. *3 The grill will not open even upon impact. Easier connection with the centralised control system. 16 OUTDOOR UNIT Technology for energy efficiency New Compact Outdoor unit RZR100LVVM Easy installation and maintenance Energy saving Pre charged for up to 30 metres 4-direction piping offers greater layout freedom (RZR/RZQ100-140 only) If refrigerant piping length does not exceed 30 m, there is no need for on-site gas charging. The outer panel for the piping connection part of the front, right side and backside can be removed and is easier for post-installation piping work. Through use of a V-cut propeller fan that imitates the efficiency of the swan, a migratory bird, airflow becomes smooth and loss is reduced. Long piping length Allowed refrigerant piping length and level difference 70 m 50 m Max. length (Equivalent length 70m) (Equivalent length 90m) Max. level difference Conventional NEW (RZQ71KC) (RZR71LV) 770 mm Weight 68 kg NEW (RZQ100KC) (RZR100LV) Weight 1,170 mm 98 kg Reduced by 175 mm mm RZQ71KCVLT Reduced by 25 kg RZR71LVVM AC motor 30 60 90 120 Large load High capacity Note: Data are based on studies conducted under controlled conditions at a Daikin laboratory. 990 990 mm 78 kg Reduced by 20 kg mm The Automatic night quiet mode will initiate 8 hours after the peak temperature is reached in the daytime, and normal operation will resume 10 hours after that. Sound level (dB(A)) Rated Night Quiet Mode RZR50/60/71LV 48 44 RZR100LV RZQ100/125/140KC RZQ100LU 49 45 RZR125LV RZQ125/140LU 50 45 RZR140LV 50 46 Note : 1Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions. 2 Value when cooling. Value will differ when heating. 22:003 8:003 100 8 hours 50 Load (%) Operation Sound4 (dB(A)) 1 Capacity (%) Peak in outdoor temperature 10 hours Use of an optimised sine wave smoothes motor rotation, further improving operating efficiency. Sine wave DC inverter RZR50/60/71/100LV >> Swing compressor As the bottom frame is subject to corrosion, corrosion-proof galvarium steel plate is adopted to enhance the durability. Energy savings is realised, eliminating the friction and the leakage of refrigerant gas. Heat exchange fins provided with anti-corrosion treatment Non-treated fin Aluminium Anti corrosion treated heat exchangers Hydrophilic film Aluminium Corrosion resistant acrylic resin 2 Swing bushing Refrigerant gas Piston by incorporated blade and roller. RZR125/140LV, RZQ100/125/140KC, RZQ100/125/140LU Sucked gas is compressed in the scrolling part before the heated motor, so that the machine compress the non-expanded gas, resulting Discharge in high efficiency compression. Smooth Air Inlet Bell Mouth and Aero Spiral Fan (RZR/RZQ100-140 only) With the bent blade edge Scroll section Motor section Without the bent blade edge These two features work to reduce noise. Guides are added to the bell mouth intake to reduce turbulence in the airflow generated by fan suction. The Aero Spiral Fan features fan blades with the bent blade edges, further reducing turbulence. Escaping eddies are sucked in by the bent blade edges, reducing overall turbulence. (RZR/RZQ100-140 only) The maximum capacity is maintained within a set level of power consumption, which makes it possible to keep comfort and effective demand control. Suction >> The structural scroll 3 DC fan motor Efficiency improved in all areas compared to AC motors, especially at low speeds. DC fan motor structure Limitation 0 49 Power consumption Reducing noise will reduce capacity slightly. >> Smooth sine wave DC inverter Imitating the performance of the swan Demand Control Function RZR100LVVM Night time quiet operation function 2 *1. A neodymium magnet is approximately 10 times stronger than a standard ferrite magnet. *2. The torque created by the change in power between the iron and magnet parts. Construction Reduced by 180 mm RZQ100KCVLT 17 70 Small load Low capacity Durability 595 595 mm 43 kg Conventional Height Conventional DC motor More than 20% Rotational speed (rps) Effective gas monitoring reduces the labor required for operation, maintenance, and repairs. Comparison of outdoor units Height 80 0 Low gas pressure detection function Reduced installation work thanks to light, compact outdoor unit. 1 50 30 m Compact and lightweight 2 Reluctance DC motor Reluctance DC Motor 90 *Pump-down function is available for pre-charged refrigerant amount. Note : 1Additional refrigerant charging is required if the refrigerant pipe is longer than the length. 3 60 (Refrigerant recovery function) A pump-down switch is provided to make it easier to collect refrigerant if the unit is to be moved or layout modified. 30 m Compressor equiped with Reluctance DC motor Daikin DC Inverter models are equipped with the Reluctance DC motor for compressor. The Reluctance DC motor uses 2 different types of torque, neodymium magnet*1 and reluctance torque*2. This motor can save energy because it generates more power with a smaller electric power than an AC or conventional DC motor. Φ550 V-cut propeller fan Facilitates pump down RZR50-140LV RZQ100-140KC/LU Pre charged1 Separation available 1 Motor efficiency (%) RZR50LVVM RZR60LVVM RZR71LVVM The high efficiency compressor to achieve a high COP RZR125LVVM RZR140LVVM RZQ100KCTLT RZQ125KCTLT RZQ140KCTLT RZQ100LUYLT RZQ125LUYLT RZQ140LUYLT Rated 45 Quiet mode 8:00 12:00 16:00 20:00 Quiet mode 0:00 4:00 8:00 Note : 3In case of RZQ series, period selectable from 22-8:00, 22-6:00, and 20-8:00. 4 In case of RZR100 8:00 12:00 16:00 20:00 Time * Required for KRP58M51 (Option) 18 LCD REMOTE CONTROLLER Optional accessory Easy-to-read LCD remote controller allows various system control configurations and can control multiple indoor units. Remote controller options are shown on the page introducing each indoor unit model. Navigation Remote Controller (Wired Remote Controller BRC1E62) Wired LCD remote controller Easy to read because of large LCD screen. The rubber switch and the oil-resistant plastic casing are adopted for durability. This simple, modern designed remote controller with fresh white colour matches your interior design. Operation is much easier and smoother, just follow the indications on the navigation remote controller. NEW Only 17 mm thick. Can be installed either recessed or exposed. Wired remote controller has built-in temperature-sensor (Applies to wired remote controllers (BRC1C61/1E62)) Enables temperature sensing closer to target area for improved comfort. (When using remote control from another room, temperature-sensor in indoor unit's air inlet must be selected.) Facilitates maintenance and repair All initial settings can be set from the remote controller. After interior construction is complete, ceiling mounted cassette type can be remotely set without having to use stepladder access for manual setting. BRC1C61 Setting contents: High ceiling use, air direction, filter type, address Clear Display LCD wireless remote controller Dot matrix display Backlight display A combination of fine dots enables various icons. Large text display is easy to see. Light receptor mounted type The wireless remote controller is supplied in a set with a signal receiver. Shape of signal receiver unit differs according to the indoor unit. BRC7F633F Energy saving NEW Setpoint auto reset NEW - Even if the set temperature is changed, it returns to the preset temperature after apreset period of time. - Period selectable from 30min/60min/90min/120min. Restaurant sample Restaurant opened Temperature is set to 27ºC Full tables at lunchtime Then is lowered to 24ºC for crowded room 27 °C After 30 minutes* Automatically returns to preset temperature (27ºC) Returns to 27 °C 24 °C Setpoint range set - Saves energy by limiting the min. and max. set temperature. - Avoids excessive heating or cooling. - This function is convenient when the remote controller is installed at a place where any number of people may operate it. Wireless remote controller Signal receiver unit (For ceiling mounted cassette type) Remote controller is equipped with model name and failure display functions. This facilitates service in the unlikely event of a malfunction. (Applies to wired remote controller (BRC1E62)) SkyAir shares common control with Heat Reclaim Ventilator and the other Daikin air-conditioning units, thus simplifying interlocking operations. Easily adaptable to large-scale, high-function, centralised remote control systems. Installing and connecting control wiring between SkyAir and other Daikin air-conditioning equipment is easy. Indoor units applicable for the remote controller Signal receiver unit is contained inside decoration panel or indoor unit CEILING MOUNTED CASSETTE TYPE BRC7F633F CEILING SUSPENDED TYPE BRC7GA56 WALL MOUNTED TYPE BRC7EB519 automatically DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE Off timer (programmed) Note: The signal receiver unit shown in the photograph is for mounting inside the decoration panel of the ceiling mounted cassette type. for centralised control (group control address is set automatically). BRC4C64 *Setting possible for after 30, 60, 90, and 120 minutes. - Sets and saves setting for an increment of time that automatically turns off air conditioner after a preset period of time for each time operation starts. - Period can be preset from 30 to 180 minutes in10-minute increments. LCD panel shows operating status in letters, numbers, and motion. Airflow / swing display Preset temperature / operation mode display Programming time display Convenience Weekly schedule - 5 actions per day can be scheduled for each day of the week. - The holiday function will disable schedule timer for the days that have been set as holiday. NEW - 3 independent schedules can be set. Self-diagnosis function Displays auto-swing operating status and setting position of air discharge angle. Displays preset room temperature and operating status (fan, dry, cool). Operation start and stop time can be set for individual timers up to 72 hours. The LCD also shows when it is time to clean the filter, when changeover is under centralised control, and ventilation/cleaning. Monitors operating status within the system covering 40 items, and displays a message to indicate as soon as a malfunction occurs. Multilingual display Display is available in 11 languages. (English, German, French, Spanish, Italian, Portuguese, Greek, Dutch, Russian, Turkish, and Polish). (e.g. summer, winter, mid-season) 19 20 Simple system provides a diverse assortment LCD of control modes. REMOTE CONTROLLER Control pattern Control by 1 remote controller Wired remote controller Wireless remote controller Note: Some features only available on selected models. See model pages for full list of features applicable to each unit. (Basic system) Non-polar, double-core (max. wiring length 500 m) Control by 2 remote controllers Abundance of functions that provide comfortable air-conditioning in stores and offices. Signal receiver unit installed on indoor unit Control by 1 wireless remote controller and 1 wired remote controller (See note 2, 3) For control from 2 locations such as in room and control room, exits, etc. Signal receiver unit installed on indoor unit Connects 2 wired remote controllers (See note 1) Comfort Auto-swing Delivers comfortable air-conditioning to all areas, near to and far from the air-conditioner. Programme "Dry" The air flow direction can be fixed at your desited angle by the remote controller. Swing pattern selection (standard, ceiling soiling prevention) Group control For simultaneous control of up to 16 indoor units. You can freely set 2 air discharge setting by remote controller. Automatic address setting function Automatic address setting function Signal receiver unit installed on 1 indoor unit Control by external command Operation and surveillance is carried out using the contact signal from the operation control box in the building surveillance (security) room. (2) Air direction in ceiling soiling prevention setting Optional wiring adaptor for electrical appendices is necessary Optional wiring adaptor for electrical appendices is necessary Central remote controller (option) Centralised remote control (1) Air direction in standard setting Central remote controller (option) Centralised control of up to 64 indoor groups from remote location up to 1 kilometer away. Independent up-and-down airflow Independently adjust (manually) the eight horizontal blade louvers in both up and down directions to achieve an airflow that reduces uneven room temperature. Switchable fan speed High setting provides maximum reach while low setting minimises drafts. Dehumidification is microprocessor controlled to prevent abrupt and uncomfortable changes in air temperature. Useful for reducing uncomfortable humidity without uncomfortable cooling of the room. High-ceiling application Delivers air-conditioning comfort all the way down to the floor in air-conditioning zones with high ceilings. Note:When units are installed on high ceilings, depending on the model, various restrictions concerning maximum height, air discharge direction, and choice of options may apply. Two selectable temperature-sensors Temperature-sensors are included in the indoor unit and optional wired remote controller. Temperature sensing closer to target area is possible to further increase the comfort level. Use the temperature-sensor in the indoor unit when controlling air conditioning from another room. Auto airflow rate Heat Reclaim Ventilator Heat Reclaim Ventilator Link by remote controller group control. Interlock control with Heat Reclaim Ventilator Can be operated simultaneously or independently by remote controller (set by ventilation mode) Can be operated simultaneously by remote controller (set by ventilation mode) Central remote controller (option) Zone link control by centralised control. Central remote controller (option) Heat Reclaim Ventilator Heat Reclaim Ventilator Heat Reclaim Ventilator for indoor units within a zone are operated by interlocking Can also be operated independently by remote controller. Heat Reclaim Ventilator for indoor units within a zone are operated by interlocking Note: 1BRC1E62 can connect to BRC1E62 only. 2 It is not possible to use two wireless remote controllers. 3 BRC1E62 cannot connect to wireless remote controller. Airflow rate is automatically controlled in accordance with the difference between room temperature and set temperature. High fan speed mode You can increase fan speed approximately 10% higher than the "high" setting. Applicable for wall mounted type Setpoint auto reset Even if the set temperature is changed, it returns to the preset temperature after a preset period of time. Weekly schedule timer control system. DCS302CA61 (Option) DCS301BA61 (Option) The Automatic night quiet mode will initiate 8 hours after the peak temperature is reached in the daytime, and normal operation will resume 10 hours after that. Off timer (programmed) Sets and saves setting for an increment of time that automatically turns off air conditioner after a preset period of time for each time operation starts. Setpoint range set Easily adaptable to large-scale, high-function, centralised remote Unified on/off controller Night quiet operation Remote Controller Saves energy by limiting the minimum and maximum set temperatures. Avoids excessive heating and cooling. Central remote controller Note: Wireless remote controllers have no temperature-sensor. Schedule timer DST301BA61 (Option) DCS601C51 (Option) On/Off timer Operation starts when the preset time of the ON timer elapses and stops when the preset time of the OFF timer elapses. Up to five operation ON/OFF settings can be programmed per day for each day of the week. Not only can the time be set for the operation ON setting, but also the temperature. Cleanliness Anti-bacterial air filter The Air filter has a anti-bacterial treatment to help prevent the growth of bacteria and mould on it. Centralised control, with setting as simple as it is with a standard remote controller, of up to 64 groups (1,024 indoor units) is possible. 21 Centralised control of on/off by group or all at once for up to 256 indoor units. Unified control of weekly schedule for up to 1,024 indoor units. Schedule timer sets on/off time in 1 minute units to be executed twice a day for a week at a time. With its high functionality, the full colour “all-in-one” graphic controller facilitates management of SkyAir System in a variety of ways. Silver ion anti-bacterial drain pan Mould-proof drain pan includes a silver ion antibacterial agent that assists in preventing the growth of slime, bacteria, and mould that cause smells and clogging. Mould-proof air filter Sanitary filter has mould-resistant treatment. 22 Note: Some features only available on selected models. See model pages for full list of features applicable to each unit. CEILING MOUNTED CASSETTE TYPE Work and Servicing Drain pump mechanism Steeper gradient realises more efficient condensate drainage. High-lift is especially useful for long lengths of drain piping. 50 Ceiling soiling prevention function Daikin's innovative air discharge mechanism keeps airflow away from the ceiling. Ceiling cleaning is less frequently required. Low gas pressure detection Pre charged for up to 30 metres If refrigerant piping length does not exceed 30 m, there is no need for on-site gas charging. Long-life filter Maintenance is not required for one year (two years when a ceiling mounted cassette type is used). SPECIFICATIONS Model Name Power supply Cooling capacity1,2 Rated (Min. - Max.) Power consumption COP Indoor unit Insufficient gas charging is normally hard to detect. During post-installation trials and regular inspection procedures, the refrigerant level is monitored by microprocessor to maintain proper gas pressure. Reliability is assured and maintenance and inspection can be carried out more quickly. If there is a malfunction elsewhere in the system, the fan or compressor can still be operated. Filter sign The filter sign warns you when it is time to clean the filter. *When using a wired remote controller the sign is displayed in the LCD. When using a wireless remote controller the filter sign lamp illuminates on the signal receiver unit. The operating parameters of indoor and outdoor units, and sensor data at critical locations throughout the system, are constantly monitored using a microcomputer. To facilitate quick response in the event of a malfunction, a message appears on the LCD of the remote controller and an LED on the unit illuminates. If there is a power outage while the equipment is operating, operations will restart in the same mode as before the power cut when electricity is restored. Control by 2 remote controllers Using 2 remote controllers you can operate the equipment locally or from a remote location. Note: When a wireless remote controller is used, remote control by two remote controllers is not possible. Group control by 1 remote controller You can turn up to 16 indoor units on/off with a single remote controller. (When using connected indoor units, the settings must all be the same and on/off will be simultaneous.) Two types are available: 65% and 90% colorimetry. Ultra long-life filter Requires no maintenance for about 4 years* (10,000h) in stores and offices. *For dust concentration of 0.15 mg/m3 kW W/W 5.0 (2.3-5.6) 6.0 (2.6-6.3) 7.1 (3.2-8.0) 1.03 4.87 1.40 4.30 1.99 3.57 2.78 3.60 Unit Decoration panel Certified Operation range Cooling Colour Type Compressor Motor output Refrigerant charge (R-410A) Cooling Night quiet mode Dimensions (HXWXD) Machine weight Certified Operation range Cooling Liquid (Flare) Piping connections Gas (Flare) Drain Indoor unit Outdoor unit m3/min cfm dB(A) mm 21/13.5 741/477 35/28 256X840X840 mm kg kg 21 *Required for KRP58M51 (Option) Central remote control Optional central remote controller enables centralised control of up to 1024 indoor units (64 groups) from up to 1 kilometer away. kW Hermetically sealed swing type 1.35 1.76 1.12 Cooling Colour Note: *Connecting ducts, insect nets, fire dampers, air filters, and other parts should, as required, be procured locally. **Outside Air fan interlocked with air conditioning unit is necessary. Optional PCB(KRP1C63)is required for interlocking. ***It is recommended that the volume of outdoor air introduced through the kit is limited to 10% of the maximum airflow rate of the indoor unit. Introducing higher quantities will increase the operating noise and may also influence temperature sending. Cooling Night quiet mode Dimensions (HXWXD) Machine weight Certified Operation range Cooling Liquid (Flare) Piping connections Gas (Flare) Drain Indoor unit Outdoor unit Max. interunit piping length Max. installation level difference Heat insulation 21/13.5 741/477 35/28 256X840X840 21 2.4 2.03 Hermetically sealed scroll type 3.1 2.4 48 44 595X845X300 43 49 50 45 46 1,170X900X320 97 45 990X940X320 78 21 to 46 o/ 9.5 o/ 15.9 3.1 46 VP25 (I.D o/ 25XO.D o/ 32) o/ 26.0 (Hole) 50 (Equivalent length 70) 30 100 125 140 100 125 140 FCQ100KVLT FCQ125KAVLT FCQ140KAVLT FCQ100KVLT FCQ125KAVLT FCQ140KAVLT RZQ100KCTLT RZQ125KCTLT RZQ140KCTLT RZQ100LUYLT RZQ125LUYLT RZQ140LUYLT 10.0 (5.0–11.4) 3 Phase, 220V, 60Hz 12.5 (6.0–14.3) 13.3 (6.2–15.8) 10.0 (5.0–11.4) 3 Phase, 380V, 60Hz 12.5 (6.0–14.3) 13.1 (6.2–15.8) 2.77 3.61 3.47 3.60 3.91 3.40 2.77 3.61 3.51 3.56 3.85 3.40 ---------- Unit Decoration panel Unit Decoration panel Certified Operation range Cooling Colour Type Compressor Motor output Sound level3 You can provide air-conditioning with fresh air from outside. Convenient for places where a ventilation fan cannot be installed. kW W/W Refrigerant charge (R-410A) Fresh-air intake kit 4.91 2.85 3.15 (Charged for 30 m) mm mm m m kW Machine weight Outdoor unit 3.68 3.40 2.7 (Charged for 30 m) Outdoor unit Sound level (H/L)3 Unit Dimensions (HXWXD) Decoration panel DIII-NET communication standard Standardly equipped interface enables connection to centralised control system without need of an adaptor. 4.91 2.85 1.6 (Charged for 30 m) dB(A) dB(A) mm kg °CDB mm mm Outdoor unit Airflow rate (H/L) Enables interlocking control with external equipment such as Heat Reclaim Ventilator. 14.0 (6.2-15.4) 14 to 25 Ivory white kg Indoor unit Power supply Cooling capacity1,2 Rated (Min. - Max.) Power consumption Interlock control 3.68 3.40 12.5 (5.7-14.0) Both liquid and gas piping Model Name COP Indoor unit 140 14.0 (6.2-15.4) Fresh white 32/20 33/22.5 1,130/706 1,165/794 43/32 44/34 44/36 298X840X840 50X950X950 24 5.5 °CWB External command control Operation and surveillance is carried out using the contact signal from the operation control box in the building surveillance (security) room. 125 ---------- Unit Decoration panel Sound level3 140 1 Phase, 220–230 V, 60 Hz 10.0 12.5 (5.0-11.2) (5.7-14.0) Heat insulation Options High-efficiency filter unit Cooling Max. interunit piping length Max. installation level difference Control features Auto-restart kW Colour 125 RZR50LVVM RZR60LVVM RZR71LVVM RZR100LVVM RZR125LVVM RZR140LVVM RZR125LVVM RZR140LVVM Outdoor unit Machine weight Self diagnosis function 100 Outdoor unit Sound level (H/L)3 Unit Dimensions (HXWXD) Decoration panel Outdoor unit 71 FCQ50KVEA FCQ60KVEA FCQ71KVEA FCQ100KVEA FCQ125KVEA FCQ140KVEA FCQ60KVEAx2 FCQ71KVEAx2 Airflow rate (H/L) Emergency operation 60 Indoor unit Fresh white m3/min cfm dB(A) mm 32/20 1,130/706 43/32 33/22.5 1,165/794 44/34 mm kg kg °CWB kW 1.9 14 to 25 Ivory white Hermetically sealed scroll type 2.9 1.8 2.4 mm mm m m 33/22.5 1,165/794 44/34 44/36 2.4 2.9 3.7 (Charged for 30 m) kg dB(A) dB(A) mm kg °CDB mm mm 32/20 1,130/706 44/36 43/32 298X840X840 50X950X950 24 5.5 49 50 45 1,170X900X320 101 99 -5 to 50 o/ 9.5 o/ 15.9 VP25 (I.D o/ 25XO.D o/ 32) o/ 26.0 (Hole) 70 (Equivalent length 90 m) 30 Both liquid and gas piping Note : 1 Rated cooling capacities are based on the following conditions: Indoor temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal). 2 Capacities are net, including a deduction for cooling for indoor fan motor heat. 3 Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions. Others Anti corrosion treated heat exchangers To achieve increased durability by improved resistance to salt corrosion and atmospheric pollution, coated Anti corrosion treated heat exchangers (with special acryl pretreatment) are used for the heat exchanger of the outdoor unit. In high corrosive areas, regular maintenance needs to be carried out. 23 24 SPECIFICATIONS CEILING SUSPENDED TYPE Indoor unit Model Name Outdoor unit Power supply 100 125 140 FHQ71CAVEB FHQ100CAVEB FHQ125CAVEB FHQ140CAVEB RZR71LVVM RZR100LVVM RZR125LVVM Cooling Power consumption COP Colour Indoor Airflow rate (SH/H/L) unit Sound level (H/M/L)3 Dimensions (HXWXD) Machine weight Certified operation range Colour Type Compressor Refrigerant charge (R-410A) Motor output Refrigerant charge (R-410A) Sound level3 Cooling Night quiet mode Dimensions (HXWXD) Machine weight Certified operation range Piping connections Liquid (Flare) Gas (Flare) Drain Indoor unit Outdoor unit Max. interunit piping length Max. installation level difference Heat insulation kW 7.1 (3.2-8.0) 10.0 (5.0-11.2) 12.5 (5.7-14.0) 13.3 (6.2-15.4) kW W/W 2.37 3.00 3.03 3.30 4.01 3.12 4.68 2.84 m3/min cfm dB(A) mm 20.5/17/14 724/600/494 38/36/34 235X1,270X690 32 28/24/20 988/847/706 42/38/34 31/27/23 1,094/953/812 44/41/37 235X1,590X690 38 34/29/24 1,200/1,024/847 46/42/38 Fresh white kg °CWB kW kg dB(A) dB(A) mm kg °CDB mm mm mm mm m m Hermetically sealed swing type 1.76 2.03 1.6 (Charged for 30 m) 2.7 (Charged for 30 m) 3.15 (Charged for 30 m) 48 44 595X845X300 43 49 50 45 46 990X940X320 78 1,170X900X320 97 21 to 46 o/ 9.5 o/ 15.9 VP20 (I.D o/ 20XO.D o/ 26) o/ 26.0 (Hole) 50 (Equivalent length 70) 30 Both liquid and gas piping Indoor unit Outdoor unit FAQ100CVEA RZR71LVVM Cooling1 kW W/W Colour Airflow rate (H/M/L) Dimensions (HXWXD) Machine weight Certified Operation range Colour Type Compressor Motor output Refrigerant charge (R-410A) Cooling Sound level3 Night quiet mode Dimensions (HXWXD) Machine weight Certified Operation range Piping Liquid (Flare) connections Gas (Flare) Drain Indoor unit Outdoor unit Max. interunit piping length Max. installation level difference Heat insulation RZR100LVVM 1 Phase, 220–240 V, 50 Hz/220–230 V, 60 Hz kW Sound level (H/M/L)3 Outdoor unit FAQ71CVEA Outdoor unit COP Indoor unit 100 7.1 (3.2-8.0) 10.0 (5.0-11.2) 2.19 3.24 3.37 2.97 kW kg dB(A) dB(A) mm kg °CDB mm mm mm mm m m 18/16/14 635/565/494 45/42/40 290X1,050X238 13 14 to 25 Ivory white Hermetically sealed swing type 1.76 1.6 (Charged for 30 m) 48 44 595X845X300 43 21 to 46 o/ 9.5 o/ 15.9 VP13 (O.D o/ 18 X I.D o/ 13) o/ 26.0 (Hole) 50 (Equivalent length 70m) 30 Both liquid and gas piping Note : 1 Rated cooling capacities are based on the following conditions: Indoor temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal). 2 Capacities are net, including a deduction for cooling for indoor fan motor heat. 3 Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions. 25 6.0 (2.6-6.3) 7.1 (3.2-8.0) 10.0 (5.0-11.2) 12.5 (5.7-14.0) 14.0 (6.2-15.4) 12.5 (5.7-14.0) 14.0 (6.2-15.4) Cooling kW W/W 1.39 3.60 1.69 3.56 2.22 3.20 2.82 3.55 3.73 3.35 4.71 2.97 3.73 3.35 4.71 2.97 Cooling m3/min cfm 18/15 635/530 32/23 1,130/812 37/32 38/33 300X1,000X700 36 Hermetically sealed swing type 1.76 1.35 1.12 37/32 40/36 ---------- 5 300X1,400X700 300X1,000X700 46 36 14 to 25 Ivory white Hermetically sealed scroll type 2.9 2.03 2.4 2.4 2.9 1.6 (Charged for 30 m) 2.7 (Charged for 30 m) 3.15 (Charged for 30 m) 48 44 595X845X300 43 49 50 45 46 1,170X900X320 97 dB(A) dB(A) mm kg 45 990X940X320 78 21 to 46 o/ 9.5 o/ 15.9 VP25 (I.D o/ 25XO.D o/ 32) o/ 26.0 (Hole) 50 (Equivalent length 70) 30 Both liquid and gas piping °CDB mm mm mm mm m m 46 100 125 140 100 125 140 Indoor unit FBQ100DAVET FBQ125DAVET FBQ140DAVET FBQ100DAVET FBQ125DAVET FBQ140DAVET Outdoor unit RZQ100KCTLT RZQ125KCTLT RZQ140KCTLT RZQ100LUYLT RZQ125LUYLT RZQ140LUYLT 1 Phase, 220V, 60Hz 10.0 (5.0–11.4) 3 Phase, 220V, 60Hz 12.5 (6.0–14.3) 13.3 (6.2–15.8) 10.0 (5.0–11.4) 3 Phase, 380V, 60Hz 12.5 (6.0–14.3) 13.1 (6.2–15.8) W/W 3.13 3.19 3.96 3.16 4.22 3.15 3.13 3.19 3.96 3.16 4.16 3.15 m3/min cfm 32 / 23 1,130 / 812 kW kW Cooling ---------- Colour Airflow rate (H/L) Cooling External static pressure (Middle-High) 4 Sound level Cooling (H/L) Air filter Dimensions (HXWXD) Machine weight Certified Operation range Cooling 39 / 28 1,377 / 988 dB(A) Type Motor output Refrigerant charge (R-410A) Sound level4 Cooling Night quiet mode 38 / 33 40 /36 mm kg °CWB Dimensions (HXWXD) Machine weight Certified Operation range Cooling Liquid (Flare) Piping connections Gas (Flare) Drain Indoor unit Outdoor unit Max. interunit piping length Max. installation level difference kW kg dB(A) dB(A) mm kg °CDB mm mm mm mm m m 39 / 28 1,377 / 988 32 / 23 1,130 / 812 50-200 3 Pa Colour Compressor Heat insulation 18/15 635/530 39/28 1,377/988 50-200 3 Pa Indoor unit Outdoor unit Cooling capacity1,2 Rated (Min. - Max.) Power consumption Outdoor unit 2.03 2.7 (Charged for 30 m) 49 45 900X940X320 78 5.0 (2.3-5.6) 4 Power supply 26/23/19 918/812/671 49/45/41 340X1,200X240 17 140 kW Cooling Night quiet mode Dimensions (HXWXD) Machine weight Certified Operation range Cooling Piping Liquid (Flare) connections Gas (Flare) Indoor unit Drain Outdoor unit Max. interunit piping length Max. installation level difference Heat insulation Fresh white m3/min cfm dB(A) mm kg °CWB 125 1 Phase, 220 V, 60 Hz 1 Phase, 220–230 V, 60 Hz Sound level4 Cooling (H/L) dB(A) Air filter mm Dimensions (HXWXD) kg Machine weight Certified Operation range Cooling °CWB Colour Type Compressor Motor output kW Refrigerant charge kg (R-410A) Fan 140 ---------- Sound level COP Indoor unit 125 RZR50LVVM RZR60LVVM RZR71LVVM RZR100LVVM RZR125LVVM RZR140LVVM RZR125LVVM RZR140LVVM Airflow rate (H/L) Model Name 71 100 Outdoor unit External static pressure (Middle-High) Outdoor unit 71 FBQ50DAVET FBQ60DAVET FBQ71DAVET FBQ100DAVET FBQ125DAVET FBQ140DAVET FBQ60DAVETx2 FBQ71DAVETx2 Indoor unit Outdoor unit Fan unit 60 Indoor unit Cooling capacity1,2 Rated (Min. - Max.) Power consumption COP Colour Indoor Hermetically sealed scroll type 2.4 3.1 WALL MOUNTED TYPE Power supply Cooling capacity1,2 Rated (Min. - Max.) Power consumption Power supply 14 to 25 Ivory white Note : 1 Rated cooling capacities are based on the following conditions: Indoor temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal). 2 Capacities are net, including a deduction for cooling for indoor fan motor heat. 3 Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions. Model Name 50 Model Name RZR140LVVM 1 Phase, 220–240 V, 50 Hz/ 220–230 V, 60 Hz 1 Phase, 220–230 V, 60 Hz Outdoor unit Cooling capacity1,2 Rated (Min. - Max.) Outdoor unit DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE 71 1.9 2.4 38 / 33 ---------- 5 300X1,400X700 46 14 to 25 Ivory white Hermetically sealed scroll type 2.9 1.8 3.7 (Charged for 30 m) 40 /36 2.4 2.9 50 49 45 1,170X900X320 99 101 -5 to 50 o/ 9.5 o/ 15.9 VP25 (I.D o/ 25XO.D o/ 32) o/ 26.0 (Hole) 70 (Equivalent length 90 m) 30 Both liquid and gas piping Note : 1 Rated cooling capacities are based on the following conditions: Suction temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal) 2 Capacities are net, including a deduction for cooling for indoor fan motor heat. 3 Initial setting is standard. 4 Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions. 5 Air filter is not standard accessory, but please mount it in the duct system of the suction side. Select its dust collection efficiency(gravity method) 50% or more. 26 Round flow type: List of optional parts required to achieve different flow patterns SPECIFICATIONS For each flow pattern – all round, 4-way, 3-way, 2-way, branch duct connection – the compatibility of each independently installed option (shown in the column on the left) to accessory options (listed across the top of each table) is shown in the cells where the relevant row and column intersect. A circle (o) indicates compatibility, and a cross (x) indicates incompatibility. Any options not shown below are not suitable for independent or accessory installation. FLOOR STANDING TYPE Indoor unit Model Name Outdoor unit Power supply Outdoor unit 60 71 FVQ50CVE FVQ60CVE Fan Airflow rate (H/M/L) Cooling Cooling Night quiet mode Dimensions (HXWXD) Machine weight Certified Operation range Cooling Piping Liquid (Flare) connections Gas (Flare) Indoor unit Drain Outdoor unit Max. interunit piping length Max. installation level difference Heat insulation 140 125 140 Optional accessory parts Independently installable optional parts 1 Phase, 220–240 V, 50 Hz/220–230 V, 60 Hz kW W/W 5.0 (2.3-5,6) 1.27 3.94 6.0 (2.6-6.3) 1.84 3.26 7.1 (3.2-8.0) 2.58 2.75 18/16/14 635/565/494 43/41/38 1,850X600X270 39 3 m /min cfm dB(A) mm kg Sound level3 Cooling (H/M/L) Dimensions (HXWXD) Machine weight Certified Operation range Cooling °CWB Colour Type Compressor Motor output kW Refrigerant charge kg (R-410A) Sound level3 125 RZR50LVVM RZR60LVVM RZR71LVVM RZR100LVVM RZR125LVVM RZR140LVVM RZR125LVVM RZR140LVVM kW Cooling 100 FVQ71CVEB FVQ100CVEB FVQ125CVEB FVQ140CVEB FVQ60CVEx2 FVQ71CVEBx2 Outdoor unit Cooling capacity1,2 Rated (Min. - Max.) Power consumption COP Colour Indoor unit All round flow 4-way flow 50 1.12 Hermetically sealed swing type 1.35 1.76 1.6 (Charged for 30 m) 48 44 595X845X300 43 dB(A) dB(A) mm kg °CDB mm mm mm mm m m 12.5 13.5 12.5 13.5 10.0 (5.7-14.0) (6.2-15.4) (5.7-14.0) (6.2-15.4) (5.0-11.2) 5.40 5.40 4.39 3.28 4.39 2.50 2.50 2.85 3.05 2.85 Fresh white 18/16/14 28/25/22 28/26/24 30/28/26 635/565/494 988/883/777 988/918/847 1,059/988/918 43/41/38 50/47/44 51/48/46 53/51/48 1,850X600X350 1,850X600X270 47 39 14 to 25 Ivory white Hermetically sealed scroll type 3.1 2.03 2.4 3.1 2.4 2.7 (Charged for 30 m) 49 45 990X940X320 78 21 to 46 o/ 9.5 o/ 15.9 VP20 (I.D o/ 20XO.D o/ 26) o/ 26.0 (Hole) 50 (Equivalent length 70) 30 Both liquid and gas piping 3.15 (Charged for 30 m) 50 45 46 1,170X900X320 97 Panel spacer1 o Panel/grille related Panel spacer1 Operation control related Wireless remote controller Auxillary function related Fresh air intake kit (Chamber type)1,2 o o o x o o Fresh air intake kit (direct mount) High-humidity operation kit Filter related Wireless Fresh air intake kit Fresh air intake kit remote controller (Chamber type)1,2 (direct mount) High-efficiency filter2 Ultra-long-life filter2 o o o o o o o o o x x x o o o o o High-humidity operation kit High-efficiency filter2 Ultra-long-life filter2 x o x o o o o o x o o o o x x x x x High-humidity operation kit High-efficiency filter2 x o x o x x x x x x x High-humidity operation kit High-efficiency filter2 Ultra-long-life filter2 x x x x x x o o o 3-way flow 2-way flow Optional accessory parts Independently installable optional parts Panel spacer1 o3 Panel/grille related Panel spacer1 Operation control related Wireless remote controller Auxillary function related Fresh air intake kit (Chamber type)1,2 o3 o3 o3 x o3 Fresh air intake kit (direct mount) High-humidity operation kit Filter related Wireless Fresh air intake kit Fresh air intake kit remote controller (Chamber type)1,2 (direct mount) Ultra-long-life filter2 o o o o o3 o x o3 o x x o o o Ultra-long-life filter2 o3 o o o x 46 97 Note : 1 Rated cooling capacities are based on the following conditions: Suction temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal) 2 Capacities are net, including a deduction for cooling for indoor fan motor heat. 3 Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions. Branch duct connection Optional accessory parts Independently installable optional parts duct1 Branch (Chamber type) (Round duct type) Panel spacer1 1-way branch / unit 3-way flow 2-way branch / unit 2-way flow 1-way branch / unit 2-way flow Wireless Fresh air intake kit Fresh air intake kit remote controller (Chamber type)1,2 (direct mount) o x x o o o o o o o o o 4 4 4 1 In some cases, depending on how the unit is embedded in the ceiling, use of branch ducts and fresh air intake kits may not be possible. Before starting installation work make sure to check whether or not joint installation is possible. In particular, ensure that the lower fixing position caused by the addition of panel spacers is acceptable. 2 Use a chamber connection kit if two different types of optional chamber are used together. In this case, the fresh air intake kit must be installed in the upper position. 3 It is not possible to use panel spacers in a 2-way flow installation. 4 It is not possible to install a branch duct on the same side to which a fresh air intake kit (direct mount) is installed. Indoor unit CEILING SUSPENDED TYPE Name of option Long-life filter Fresh air intake kit Drain pump kit L-type piping kit (for upward direction) Remote controller OPTIONS Indoor unit CEILING MOUNTED CASSETTE TYPE Name of option Remark Decoration panel Sealing material of air discharge outlet Panel spacer Without the T-joint pipe and fan Fresh air Chamber type intake kit1 With the T-joint pipe, without fan Direct installation type Chamber connection kit2 Insulation kit for high humidity (Colorimetric method 65%) High-efficiency filter (including chamber) (Colorimetric method 90%) Replacement (Colorimetric method 65%) high-efficiency filter (Colorimetric method 90%) Filter chamber Replacement long-life filter Ultra long-life filter Replacement ultra long-life filter Branch duct chamber Wireless type Cooling only Remote controller Wired type3 Navigation Remote Controller Wired type3 Central remote controller4 Unified ON/OFF controller4 Schedule timer4 Touch Controller4 Adaptor for wiring5 Wiring adaptor for electrical appendices5 Installation box for adaptor PCB Remote sensor (for indoor temperature) Kit name FCQ50KVEA FCQ60KVEA FCQ71KVEA FCQ100KVEA FCQ125KVEA FCQ140KVEA FCQ100KVLT FCQ125KAVLT FCQ140KAVLT BYCP125K-W1 KDBH55K160F KDBP55H160FA KDDP55B160 KDDP55B160K KDDP55X160 KKSJ55KA160 KDTP55K160 KDTP55K80 KAFP556B160 KAFP556B80 KAFP557B160 KAFP557B80 KAFP552B160 KAFP552B80 KAFP553B160 KAFP553B80 KDDFP55B160 KAFP551K160 KAFP55B160 KAFP55H160H KDJP55B80 KDJP55B160 BRC7F633F BRC1C61 BRC1E62 DCS302CA61 DCS301BA61 DST301BA61 DCS601C51 KRP1C63 KRP4AA53 KRP1H98 KRCS01-4B Note: 1Refer to page 8 for the details. 2 Required for installing high-efficiency filter or ultra long-life filter. 3 Wiring for wired remote controller to be procured locally. 4 The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary. 5 Installation box for adaptor PCB (KRP1H98) is necessary. 27 Remark Wireless type Wired type1 Wired type1 FHQ71CAVEB KAFP501A80 Cooling only Navigation Remote Controller Central remote controller2 Unified ON/OFF controller2 Schedule timer2 Touch Controller2 Adaptor for wiring Wiring adaptor for electrical appendices3 Installation box for adaptor PCB Remote sensor (for indoor temperature) Electrical box with earth terminal (3 blocks) Electrical box with earth terminal (2 blocks) Kit name FHQ100CAVEB FHQ125CAVEB KAFP501A160 KDDQ50A140 KDU50P140VE KHFP5N160 BRC7GA56 BRC1C61 BRC1E62 DCS302CA61 DCS301BA61 DST301BA61 DCS601C51 KRP1BA54 KRP4AA52 KRP1D93A KRCS01-4B KJB311AA KJB212AA FHQ140CAVEB Note: 1Wiring for wired remote controller to be procured locally. 2 The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary. 3 Installation box for adaptor PCB is necessary. WALL MOUNTED TYPE Name of option Drain-up kit Remote controller Kit name Remark Wireless type Wired type1 Wired type1 FAQ100CVEA FAQ71CVEA Cooling only Navigation Remote Controller Remote sensor (for Indoor temperature) Central remote controller2 Unified ON/OFF controller2 Schedule timer2 Touch Controller2 Wiring adaptor for electrical appendices3 Installation box for adaptor PCB Electrical box with earth terminal (3 blocks) Electrical box with earth terminal (2 blocks) Noise filter ( For electromagnetic interface use only) K-KDU572EVE BRC7EB519 BRC1C61 BRC1E62 KRCS01-4B DCS302CA61 DCS301BA61 DST301BA61 DCS601C51 KRP4AA51 KRP4AA93 KJB311AA KJB212AA KEK26-1A Note: 1Wiring for wired remote controller to be procured locally. 2 The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary. 3 Installation box for adaptor PCB (KRP4AA93) is necessary. 28 OPTIONS DIMENSIONS Indoor unit (Unit: mm) CEILING MOUNTED CASSETTE TYPE DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE [FCQ50-71] [FCQ100-140] 16-M4 Hole 350 157 350 A 35 or less (Note 4) Connection position of branch duct (square-shaped type) Connection position of branch duct (round shape type) Connection position of fresh air intake kit (direct installation type) 157 350 67 95 29 157 350 2x100=200 80 25 160 80 C/L 213 C/L 160 80 130 256 167 93 Connection position of branch duct (square-shaped type) 20-M4 Prepared hole 124 27-M4 Prepared hole 5 2x100=200 25 213 60 105 2 280 330 55 42 150 35 or less (Note 4) Connection position of branch duct (round shape type) 157 840 81 2x100=200 85 64 124 50 [FCQ100-140] 160 124 109 95 80 55 3 95 110 124 16-M4 Prepared hole 55 Connection position of branch duct (square-shaped type) 1 167 [FCQ50-71] Connection position of branch duct (square-shaped type) 20-M4 Prepared hole [FCQ50-71] 4 B arrow view 90 183 ø10 (kn 0 ock hole ) Connection position of branch duct (round shape type) Connection position of fresh air intake kit (direct installation type) C arrow view 90 7 90 Hanging bolt 4-M8~M10 Connection position of branch duct (round shape type) 29 95 95 110 B arrow view 6 Connection position of branch duct (square-shaped type) Drain Connection Side 1500 or more (required space) 160 From the floor side 2500 or more For height installation 20 C/L 16-M4 Hole 157 350 Connection position of branch duct (square-shaped type) A arrow view 840 340 80 2x100=200 80 124 Connection position 85 of branch duct (round shape type) 2x100=200 160 C/L 93 160 124 157 350 950 C 81 160 67 8 [FCQ50-71] 55 Note 2 Piping Connection Side Connection position 85 of branch duct (round shape type) 2x100=200 124 C/L 81 950 420 160 246 10 Note: 1If installing a high efficiency filter on the unit, an assembly chamber for either bottom or rear suction is required. 2 Wiring for wired remote controller to be procured locally. 3 The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary. 4 Mounting plate for adaptor PCB is necessary for each adaptor marked . 5 Up to 2 adaptors can be fixed for each mounting plate. 6 Only one mounting plate can be installed for each indoor unit. 9 860~910(Ceiling opening space) (Note 4) 710(Hanging bolt pitch) 420 780(Hanging bolt pitch) Cooling only 300 or less 860~910(Ceiling opening space) (Note 4) Wireless type Wired type2 Navigation Remote Controller Wired type2 Adaptor for wiring (interlock for fresh air intake fan) Wiring adaptor for electrical appendices Remote sensor Mounting plate for adaptor PCB.4 Central remote controller3 Unified ON/OFF controller3 Schedule timer3 Touch Controller3 [FCQ50-140] B 125 165 256 Air discharge adaptor Remote controller [FCQ50-140] 95 110 124 Filter chamber Replacement long life filter Replacement long life filter chamber kit Service panel FBQ125DAVET FBQ140DAVET KAF372AA160 KAF373AA160 KDDF37AA160 KAF371AA160 KAF375AA160 KTB25KA160W KTBJ25K160F KTBJ25K160T KDAJ25K140A 850 Adjustable(0~675) 65% 90% High-efficiency filter1 Kit name FBQ50DAVET FBQ60DAVET FBQ71DAVET FBQ100DAVET KAF372AA80 KAF373AA80 KDDF37AA80 KAF371AA80 KAF375AA80 KTB25KA80W KTBJ25K80F KTBJ25K80T KDAJ25K71A BRC4C64 BRC1C61 BRC1E62 KRP1C64 KRP4AA51 KRCS01-4B KRP4A96 5,6 DCS302CA61 DCS301BA61 DST301BA61 DCS601C51 175 Remark 50 40 Name of option 90 196 ø10 (kn 0 ock hole ) C arrow view FLOOR STANDING TYPE Outdoor unit Name of option Central drain plug Wire fixture for preventing overturning Fixture for preventing overturning Demand adaptor Refrigerant branch piping kit RZR50LVVM For twin multi Name of option Central drain plug Fixture for preventing overturning Demand adaptor 29 Base stationary type Wire type Kit name RZR60LVVM RZR71LVVM RZR100LVVM RZR125LVVM RZR140LVVM KKP014A4 KKPJ5G280 KKPJ5F180 ------------------K-KYZP15C KPT-60B160 ---------KKTP5B112 KRP58M51 ------------------KHRP58P216T [FCQ100-140] Required space 200mm or more 16-M4 Prepared hole Hanging bolt 4-M8~M10 Connection position of branch duct (round shape type) 157 280 330 4 1 2 35 or less (Note 4) Connection position of branch duct (round shape type) 55 27-M4 Prepared hole 5 95 167 93 29 60 42 125 165 20 C/L 350 3 840 81 2x100=200 85 160 64 50 130 Connection position of branch duct (square-shaped type) 105 340 80 2x100=200 80 160 55 150 55 840 160 298 55 256 157 350 A 1500 or more 67 (required space) 160 From the floor side 2500 or more For height installation Note: 1Wiring for wired remote controller to be procured locally. 2 The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary. 3 Installation box for adaptor PCB (KRP4AA95) is necessary. [FCQ100-140] 95 167 Wired Wired type1 Kit name FVQ71CVEB FVQ100CVEB FVQ125CVEB FVQ140CVEB KAFJ95L160 BRC1C61 BRC1E62 DCS302CA61 DCS301BA61 DST301BA61 DCS601C51 KRP1BA57 KRP4AA52 KRP4AA95 850 Adjustable(0~675) type1 FVQ60CVE 175 29 Replacement long-life filter Remote controller Navigation Remote Controller Central remote controller2 Unified ON/OFF controller2 Schedule timer2 Touch Controller2 Adaptor for wiring3 Wiring adaptor for electrical appendices Installation box for adaptor PCB FVQ50CVE 160 288 10 Remark 50 40 Name of option 1500mm or more 1500mm or more 1500mm or more 200mm or more 1500mm or more The necessary space is 500mm or more when the air-outlet is blocked with the accessory. Moreover when the corner areas are blocked (both right and left of the blocked air outlet), the necessary space is 200mm or more. 35 or less (Note 4) Connection position of branch duct (square-shaped type) Notes: 1 Sticking location for manufacture's label manufacture's label for indoor unit: Suction grille inner side's electric components box's lid surface manufacture's label for decoration panel : Decoration panel's corner decoration cover inner surface 2 In case of using wireless remote controller, this position will be a signal receiver. Refer to the drawing of wireless remote controller in detail. 3 When the temperature and humidity in the ceiling exceed 30˚C and RH 80% or the fresh air is inducted into the ceiling or the unit continues 24 hour operation, an additional insulation (thickness 10mm or more of glasswool or polyethylene form) is required. 4 Though the installation is acceptable up to maximum of 910mm square ceiling opening, keep the clearance of 35mm or less between the indoor unit and the ceiling opening so that the panel overlap allowance can be ensured. 5 Please do not place the thing been damp and troubled under an indoor unit. When the case where humidity is 80% or more, and the drain outlet are choked up and the air filter are dirty, dew may fall. 1 2 3 4 5 6 7 8 9 Liquid piping connection Gas piping connection Drain piping connection Transmission wiring connection Remote controller wiring connection Air-outlet Suction grille Corner decoration cover Drain hose (accessory) Kit name RZQ100KCTLT RZQ125KCTLT RZQ140KCTLT RZQ100LUYLT RZQ125LUYLT RZQ140LUYLT KKPJ5F180 KPT-60B160 K-KYZP15C KRP58M51 30 (Unit: mm) WALL MOUNTED TYPE CEILING SUSPENDED TYPE 157 63 115 1230 4 11 5 57 6 30 or more (Service space) 30 or more (Service space) 1270 Obstacle Floor side 214 221 268 268 6 3 2 7 83 105 156 5 4 Notes: 1 Location of unit's Name Plate: Bottom of fan housing inside the suction grille. 2 In case of using wireless remote controller, this position will be a signal receiver. Refer to the drawing of wireless remote controller in detail. 3 Please do not place the thing been damp and troubled under an indoor unit. When the case where humidity is 80% or more, and the drain outlet are choked up and the air filter are dirty, dew may fall. Piping direction 1 Name plate Note)2 Piping direction 1050 104 50 or more (Requred space) 894 2500 or more For installation in high spaces 120 or less 52 φ80 hole Piping and Wiring intake Outside line φ80 hole 60 Mounting location 6 5 4 Approx.345 1 2 3 4 5 6 7 8 9 98 Approx.390 Approx.475 Notes: 1 Location of unit's of Name Plate:Right side surface of casing 2 In case of using wireless remote controller, this position will be a signal receiver. Refer to the drawing of wireless remote contorller in detail. 3 Please do not place the thing been damp and troubled under an indoor unit. when the case where humidity is 80% or more, and the drain outlet are choked up and the air filter are dirty, dew may fall. Front panel Front grill Air outlet Gas piping Liquid piping Drain hose Earth terminal Right side piping connection hole Left side piping connection hole Connection position of fresh air intake kit φ100(Knock out hole) 120 90 12 10 157 63 115 90 175 92 51 60 50 or more (Required space) 116 Piping direction 9 40 260 [FAQ100CVEA] Approx.440 63 134 59 242 240 Position slit hole for taking out in piping back (View from the front) 7 30 or more (Service space) 1590 Obstacle Floor side 30 or more (Service space) The Front Brand name plate (Note.2) Drain piping connection VP20 (For left piping) 214 221 268 268 6 76 3 2 7 5 83 105 156 4 Notes: 1 Location of unit's Name Plate: Bottom of fan housing inside the suction grille. 2 In case of using wireless remote controller, this position will be a signal receiver. Refer to the drawing of wireless remote controller in detail. 3 Please do not place the thing been damp and troubled under an indoor unit. When the case where humidity is 80% or more, and the drain outlet are choked up and the air filter are dirty, dew may fall. 6 o/ 45 14 Position : Hole of wall for taking out in piping back (View from the front) 1 Air discharge grille 2 Air suction grille 3 Air filter 4 Gas piping connection 5 Liquid piping connection 6 Drain piping connection 7 Earth terminal (inside the control box) (M4) 8 Hanger 9 Rear piping penetration cover 10 Top panel penetration cover 11 Right side piping connection 12 Left back drain piping connection 13 Left side drain piping connection 14 Right side drain piping connection 15 Hole of wall for taking out in piping back 16 Upward drain piping connection 17 Upward gas piping connection 18 Upward liquid piping connection 19 Power supply wiring and a unit wiring back connection 20 Power supply wiring and a unit wiring upper connection 9 2 1 30 or more (Required space) 50 or more (Requred space) Piping direction 1200 79.5 3 Name plate Note)2 Piping direction 1085 2500 or more For installation in high spaces 50 or more (Requred space) 8 120 or less 35.5 φ80 hole Outside line Piping and Wiring intake φ80 hole 6 65 5 Mounting location 4 Approx.400 89 Approx.460 Approx.465 Notes: 1 Location of unit's of Name Plate:Right side surface of casing 2 In case of using wireless remote controller, this position will be a signal receiver. Refer to the drawing of wireless remote contorller in detail. 3 Please do not place the thing been damp and troubled under an indoor unit. when the case where humidity is 80% or more, and the drain outlet are choked up and the air filter are dirty, dew may fall. 114 235 300 or more (Required space) 57 13 57 Dimensions for full open front panel 45 11 91 131 197 5 220 103 14.5 4 1 19 15 45 Hanging bolt 4-M8~M10 175 690 340 1550 (Hanging bolt pitch) 5 (Required space) 8 5 (Required space) For height installation (Hanging bolt pitch) 210 18 17 20 16 210 156 105 102 131 57 30 87 100 163 189 195 35 [FHQ100-140CAVEB] From the floor side 2500 or more 197 2 WALL MOUNTED TYPE CEILING SUSPENDED TYPE 31 8 3 9 50 or more (Requred space) 1 Air discharge grille 2 Air suction grille 3 Air filter 4 Gas piping connection 5 Liquid piping connection 6 Drain piping connection 7 Earth terminal (inside the control box) (M4) 8 Hanger 9 Rear piping penetration cover 10 Top panel penetration cover 11 Right side piping connection 12 Left back drain piping connection 13 Left side drain piping connection 14 Right side drain piping connection 15 Hole of wall for taking out in piping back 16 Upward drain piping connection 17 Upward gas piping connection 18 Upward liquid piping connection 19 Power supply wiring and a unit wiring back connection 20 Power supply wiring and a unit wiring upper connection Brand name plate (Note.2) 76 Position : Hole of wall for taking out in piping back (View from the front) 14 o/ 45 The Front Drain piping connection VP20 (For left piping) Dimensions for full open front panel 105 13 57 300 or more (Required space) 235 91 131 197 1 220 103 44 Hanging bolt 4-M8~M10 19 15 7 14.5 690 240 238 Position slit hole for taking out in piping back (View from the front) (Hanging bolt pitch) 50 or more (Required space) 10 Approx.400 63 134 59 12 30 or more (Required space) 60 5 175 (Required space) 5 (Required space) For height installation 90 92 51 Piping direction 290 116 9 90 8 From the floor side 2500 or more 197 Connection position of fresh air intake kit φ100(Knock out hole) 120 40 260 (Hanging bolt pitch) 210 18 17 20 16 [FAQ71CVEA] 175 210 156 105 102 131 57 30 87 100 163 189 195 35 [FHQ71CAVEB] 44 DIMENSIONS 1 2 3 4 5 6 7 8 9 Front panel Front grill Air outlet Gas piping Liquid piping Drain hose Earth terminal Right side piping connection hole Left side piping connection hole 32 DIMENSIONS (Unit: mm) DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE Suction grille stopper P 150 B Ceiling Inspection hatch 700 Inspection hatch 2 or more (same as the indoor View B-1 unit size or more) (From the Air outlet) 18-8X12 oblong hole (All around) 513 541 616 80 According to any one of below 1) ~3), secure a space for service works, such as, checking and maintenance of control box, etc. 1) One inspection hatch (450X450) on the control box side and a space of 300mm or more under the unit. (Fig.A) 2) One inspection hatch (450X450) on the control box side and 2 (two) inspection hatches under the unit. (Arrow View B-1) 3) 3 (three) inspection hatches under the unit and the control box. (Arrow View B-2) 95 A B 200 223 253 34 (From the Air inlet) Floor surface Notes) Location of MANUFACTURE'S LABEL: Control box surface 2 Mount the air filter at the suction side. (Select its colorimethod (gravity method) 50% or more.) 3 Do not locate things should not be wet under the indoor unit. Dews may drop when humidity reaches over 80%, or a drain gets stuck, or air filters are not clean. 4 Space for Service Works 1 50 Liquid pipe connection Gas pipe connection Drain pipe connection Ground terminal (Terminal in Control box) Control box (Inside) Remote control wiring connection Power-source wiring and a unit wiring connection 8 Air discharge flange 9 Air suction flange 10 Hook 950 100 1 2 3 4 5 6 7 925 C [FBQ100/125/140DAVET] 326 300 20 342 7 Air inlet 200 or less 300 or more 131 Control box 5 4 30 6 6 6 H J K L 184 184 A B C D FVQ50/60CVE, 71CVEB 50 110 186 270 FVQ100/125/140CVEB 130 190 266 350 mo Required space E 45 44 F 50 49 G H J K L 50 110 180 186 242 130 190 260 266 322 M 57 79 N P 144 149 202 229 78 573.5 80 8X150=1200 1325 1350 (From the Air inlet) Floor surface Notes: 1 Location of MANUFACTURE'S LABEL: Control box surface 2 Mount the air filter at the suction side.(Select its colorimethod (gravity method) 50% or more. 3 Do not locate things should not be wet under the indoor unit.Dews may drop when humidity reaches over 80%,or a drain gets stuck,or air filters are not clean. 4 Space for Service Works According to any one of below 1)~3),secure a space for service works,such as,checking and maintenance of control box,etc. 1)One inspection hatch (450X450) on the control box side and a space of 300mm or more under the unit.(Fig.A) 2)One inspection hatch (450X450) on the control box side and 2 (two) inspection hatches under the unit.(Arrow View B-1) 3)3 (three) inspection hatches under the unit and the control box.(Arrow View B-2) Earth terminal in switch box 595 200 or less Wiring inlet 60 105 20-8X12 oblong hole (All around) Name plate Service port 1 2 3 4 5 6 7 8 9 10 11 12 Liquid piping connection Gas piping connection Drain piping connection Earth terminal (Terminal in Control box) Control box(Inside) Remote control wiring connection Power supply wiring and a transmission wiring Air discharge flange Air suction flange Hanger Socket (for maintenance) Drain hose(Accessory) 272 713 or less Hole for anchor bolts (M8 or M10) 112 View (From the Air outlet) B Inspection Ceiling hatch 700 700 Inspection hatch 2 or more or more (SAME AS THE View B-1 View B-2 INDOOR UNIT SIZE OR MORE) 163 300 12 Inspection hatch 1 (450mmX450mm) Control box Inspection hatch 3 (SAME AS THE INDOOR UNIT SIZE +300 OR MORE) Control box 269 49 150 277 247 150 300 3X65=195 700 300 or more (Note.4) 2500 or more (A case without the ceiling) (467 or less) 212 144 40 2X65=130 700 or less 232 Adjustable Air inlet (Note.2) CASE 2),3) 20 or more 165 7X150=1050 700 or more (Service space) Ceiling 33 Unit base 1400 or more 635 245 215 150 200 or less 65 450 or more (Service space) (SAME AS THE INDOOR UNIT SIZE OR MORE) 20-8X12 oblong hole (All around) 1185 28 7 4 1 or Fig.A 1160 5 Control box Air outlet 1400 Inspection hatch Ceiling 9 169 11 290 re 0 50 300 1700 or more 19X65=1235 Control box Air inlet 2 6 845 Inspection hatch 1 (450mmX450mm) 48- 4.7 Hole (All around) 1205 16X65=1040 1438(Hanging bolt pitch) CASE 1) 10 8 Air outlet mo Drain outlet I.D. 18 hose for connection 631 (Hanging bolt pitch) 167 3 1 3 F 598 Notes: 1 Sticking location for manufacturer’s label: on the surface of cover of switch box inside the suction grille. or OUTDOOR UNIT // RZR50/60/71LVVM DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE Inspection hatch 450 or more G E 6X150=900 Ceilling Full open position of suction grille 825 150 247 277 (Note.4) 2500 or more (A case without the ceiling) 700 150 300 28 4 3X65=195 290 7 300 or more 26 2X65=130 212 144 3 130 Approx.46 10 50 1 Suction grille 2 Air filter 3 Through hole for side piping (70x90 oblong slit hole) 4 Through hole for side piping ( 80 slit hole) 5 Through hole for side piping ( 27 slit hole) 6 Through hole for rear piping/wiring (80x130 oblong slit hole) 7 Through hole for bottom piping/wiring (126x130 square hole) 8 Liquid pipe connection 9 Gas pipe connection 10 Drain pipe connection 1 9 Air outlet 169 2-7X15 oblong hole (For wood screw) 95 Air inlet (Note.2) 5 mo 2 50 6 8 700 or more View B-2 or re Fixture (Accessory) 75 2 1000 200 or more or less 20 or more 150 785 50 re 100 215 245 200 or less 65 450 or more (Service space) 760 1 Inspection hatch 1 (450mmX450mm) Control box Inspection hatch 3 (Same as the indoor unit size + 300 or more) Control box Control box 43 Air inlet Fig.A 330 740 or more (Pull out dimension of air-filter) Air outlet D Pull out direction of air-filter 314 Ceiling CASE2), 3) 5X150=750 N Unit base 9 Inspection hatch 450 or more Air outlet In case of fixing it at the bottom In case vibration resistance is required, fix it at both the bottom and the rear. View 68 600 677 Inspection hatch Detail (Two both sides) 1850 16-8X12 oblong hole (All around) 435 700 or more (Service space) 27 This model to be fixed with fixture as shown below. 126 0.7 1300 or more Air inlet Inspection hatch 1 (450mmX450mm) Control box 200 or less 300 or more 1000 13X65=845 805 CASE 1) Control box View 40- 4.7 Hole (All around) 130 215 7 11X65=715 1038 (Suspention bolt position) 4- 14 Hole (For bolt) 18 36-φ4.7 hole (All around) 8 Air outlet 260 10 631 (Suspention bolt position) 30-φ4.7 hole (All around) M [FBQ50/60/71DAVET] FLOOR STANDING TYPE 144 20 Liquid stop valve ( 9.5CuT) Service port Gas stop valve ( 15.9CuT) Drain outlet 21 94 Drain outlet 200 299 419 449 479 509 559 34 DIMENSIONS (Unit: mm) OUTDOOR UNIT // RZR100LVVM REMOTE CONTROLLER 350 (345~355) 30 Hole for anchor bolt 4-M12 Wireless type 37 55 320 • Remote controller dimensions CEILING SUSPENDED TYPE • Receiver installation procedure CEILING MOUNTED CASSETTE TYPE <Round Flow> • Receiver installation procedure Transmitting part The Front 30 Refrigerant piping side 620 157 91 160 Receiver Receiver 38 160 940 30 3 62 4 7 2 7 6 6 5 5 7 • 55 Remote controller holder 223 53 53 84 95 19 142 Decoration panel • Receiver detail Liquid crystal remote controller (wireless) 55 340 95 19 89 6 53 89 339 60 5 Remote controller holder installation procedure <installation to wall surface> • Receiver detail 95 990 1 Drain piping side 17.5 80 52 WALL MOUNTED TYPE • Receiver installation procedure DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE 13 145 • 67 Receiver detail 2-5x9 Slot 90 Receiver 16 (Ceiling opening) 3 Service port 4 Earth terminal 5 72 83.5 106 68 120 1 Gas piping connection 2 Liquid piping connection 161 260 279 285 16 8 • Receiver detail 5 Refrigerant piping intake 6 Power supply wiring intake 36 61 7 Transmission wiring intake 8 Drain piping connection 262 416 595 70 0.5 35 18 49 (Ceiling opening) Switch box (field Supplied parts) Service space for ceiling installation Wired type • Remote controller dimensions BRC1C61 320 61 43 • Installation method A Exposed body, exposed cord B Exposed body, embedded cord 17 Staple 620 42 140 117 0~5 900 30 84 38 94 140 120 4 17 18 Cord outlet hole 23 28 3 (Between remote controller and control box) 17 Size 0.75~1.25 mm Total length 500 m 6 6 5 BRC1E62 Upper case A Exposed cord 42 40 5X7 oblong hole 80 52 145 13 28 23 46 5X15 oblong hole 48.5 48.5 Left outlet 19 Lower case portion Note)2 28 Through hole Switch box for one switch ( 8- 10) ex.) KJB111A (optional accessory) Lower case 67 Note) 1. Remote controller cord and staple are not attached. They are field supplied parts. 16 16 58 70 102 117 35 376 191 19 Code outlet hole 19 Specifications of cord 45 Condit C Embedded cord (use switch box) 19 84 95 223 B Embedded cord Staple Top center outlet 40 120 55 Operation lamp (Green) 120 53 19 5 Note) 1. Remote controller cord and staple are not attached. They are field supplied parts. • Installation method Lower case Top left outlet 55 54 54 89 60 84 95 95 422 423 5 71 2 84 1170 7 5 8 Shield wire (insulated thickness: 1 mm or more) 7 6 142 Control box Type 7 Through hole ( 12- 16) Specifications of cord 1 19 17 46 2 89 Remote controller Remote controller 120 30 41 C Exposed body, embedded code Conduit Remote controller 84 350 (345~355) 30 Hole for anchor bolt 4-M12 Note : Do not install more than 3 receivers in the vicinity of one another. With 4 or more units, there is always the possibility of malfunction More than 90 (Srevice space) OUTDOOR UNIT // RZR125/140LVVM, RZQ100/125/140KCTLT, RZQ100/125/140LUYLT 1 Gas piping connection 2 Liquid piping connection 3 Service port 4 Earth terminal Type Vinyl cord with sheath or cable (insulated thickness: 1mm or more) Size 0.75~1.25 mm2 Total length 500 m 46 0~5 Switch box for two switch (Between remote ex.) KJB211A controller and (optional accessory) control box) Switch box portion [field supplied part] 2.If the hole size is too large or the location is not proper, the hole may come out from the remote controller. 5 Refrigerant piping intake 6 Power supply wiring intake 7 Transmission wiring intake 8 Drain outlet 36 Installation service space for outdoor unit For RZR50-140LVVM For RZQ100-140KCTLT, 100-140LUYLT 2.RZR100-140LVVM 1 When there is an obstruction on the inlet side 2 When there is an obstruction on the outlet side 1) When the overhead space is open 1) When the overhead space is open 1 1. For single unit installation 2 re or mo 0 10 ore m or 1 10 25 0o rm ore 0o 25 0o rm 0 10 ore mo or rm ore re 10 0 1 or 0 10 ore m or mo re 0 00 or mo re 1 0 00 or mo 2. For multiple units installation (more than two units) 10 0 mo or re 10 0 mo or re re 100 or m ore re 100 or m ore 2) When there is an obstruction in the overhead space When there are obstructions on both sides 50 2 0o r le An obstruction in the overhead space ss 1 50 0o r le ss 2 r 0o 10 10 00 or ss r le 0o 1. For single unit installation An obstruction in the overhead space mo re 00 o rm 0o ore mo re 0 50 50 1 0o r le 1. For single unit installation 2 50 0o r An obstruction in the overhead space 2 25 0o rm ore 0 10 0o o rm An obstruction in the overhead space re 0 10 0 0o m or mo 0 10 ore m or When there are obstructions on the inlet side and both lateral sides An obstruction in the overhead space 15 0o r le ss 2 o rm re or 150 mo re or 150 mo re 1. For single unit installation 1 1 or 000 mo re or 250 mo re (There is no limit to the height of the obstruction on the outlet side.) or m 150 e or rm o 50 or m ore 1 1. For single unit installation 50 ore m or L H 0 50 ore m or 0 10 ore m or les s 1 or 200 mo re 10 0 mo or re An obstruction in the overhead space 10 or mo rm ore ore 00 10 ore m or 0 10 ore m or 10 0 mo or re 10 0 mo or re 0 30 ore m or L H 00 10 ore m or 0 30 ore m or H 0 20 ore m or 37 Note : As for other patterns of installation, please refer to Installation manual or Engineering Data Book. 0 50 ore m or re 2 rm H 2. For multiple units installation (more than two units) 10 0o rm ore 0o 0o ss r le 0o 50 20 25 0 30 ore m or When there are obstructions on the inlet side and both sides 00 L 50 0 20 ore m or L L 2. For series installation (more than two units) r 0o 1 or 000 mo re or 250 mo re 1) When the overhead space is open 2 0 50 ore m or 1000 or more 5 1000 or more 00 (When the obstruction on the outlet side is higher than the unit itself) 2. For multiple units installation (more than two units) 0 15 ore m or An obstruction in the overhead space 2 ss 150 3 When there are obstructions on both the inlet and outlet sides (There is no limit to the height of the obstruction on the outlet side.) When there are obstructions on the inlet side and both lateral sides le or ss r le 0o 50 ore 1) When the overhead space is open 2. For series installation (more than two units) 1 An obstruction in the overhead space re mo e or When there are obstructions on the inlet side and both sides (When the obstruction on the outlet side is higher than the unit itself) or H or 250 mo re 5 o 00 An obstruction in the overhead space rm 3 When there are obstructions on both the inlet and outlet sides 10 0o rm ore 00 10 0o H s r 0o 50 10 L or 150 mo re 50 les 1000 or more 1 r 0o 1000 or more or An obstruction in the overhead space s les ore re 0 10 ss r le 0o 50 10 0 mo or re 1. For single unit installation When there is an obstruction on the inlet side mo L ss r le 50 2. For multiple units installation (more than two units) 2) When there is an obstruction in the overhead space ss ss mo 1000 or more r le 1000 or more 0o s les 1000 or more When there is an obstruction on the inlet side 50 ore ore 2. For series installation (more than two units) 2) When there is an obstruction in the overhead space 1 m or or or H rm 50 r 0o 0 30 1000 or more 0o 0 20 ore m or or 250 mo re 0 30 ore m or rm 1000 or more 20 1000 or more or 250 mo re 0 50 re 20 ore 1000 or more 1 or 000 mo re mo 50 re 10 or 10 2) When there is an obstruction in the overhead space 10 0 mo or re 10 0 mo or re When there are obstructions on both sides 00 re mo 2. For multiple units installation (more than two units) 1. For single unit installation 2. For series installation (more than two units) 1 ore rm 0o 10 1000 or more ore re mo or 0 50 2 2 rm 0o When there is an obstruction only on the inlet side re When there are obstructions on both sides 1 0o 50 o rm 2. For series installation (more than two units) When there are obstructions on both sides 10 1. For single unit installation 1. For single unit installation 0 50 ore m or 50 1) When the overhead space is open 1) When the overhead space is open 2 1000 or more When there is an obstruction only on the inlet side 2 When there is an obstruction on the outlet side 1000 or more 1. For single unit installation 1 1 When there is an obstruction on the inlet side 1000 or more 1.RZR50/60/71LVVM L H 00 10 ore m or 0 30 ore m or Note : As for other patterns of installation, please refer to Installation manual or Engineering Data Book. 38