Download ceiling mounted cassette type

PCSPH1411
Ask a
installer or contractor to install this product. Do not try to install the product by yourself.
Improper installation can result in water or refrigerant leakage, electrical shock,
or explosion.
Warning
Use only those parts and accessories supplied or
by Daikin. Ask a
installer or
contractor to install those parts and accessories. Use of unauthorised parts and accessories or
improper installation of parts and accessories can result in water or refrigerant leakage, electrical
or explosion.
shock,
Read the User's Manual carefully before using this product. The User's Manual provides important
safety instructions and warnings. Be sure to follow these instructions and warnings.
If you have any enquiries, please contact your local importer, distributor and/or retailer.
Cautions on product corrosion
1. Air conditioners should not be installed in areas where corrosive gases, such as acid gas or alkaline gas, are produced.
2. If the outdoor unit is to be installed close to the sea shore, direct exposure to the sea breeze should be avoided. If you need to install
the outdoor unit close to the sea shore, contact your local distributor.
Dealer:
2nd Floor, Hanston Square, 17 San Miguel Avenue,
Ortigas Center, Pasig City, 1605
Tel. No.: (02) 942-6800/942-6792
Fax No.: (02) 942-6793
out notice.
c All rights reserved 02/14
SS
Daikin meets your needs with this full lineup of inverters for various types
of indoor units and power supplies.
2HP
50
Series
CEILING MOUNTED
CASSETTE TYPE
NEW
2.5HP
60
3HP
71
4HP
100
NEW
5HP
125
NEW
6HP
140
NEW
Round Flow
FCQ50KVEA
Indoor unit
FCQ60KVEA
CEILING SUSPENDED
TYPE
FCQ71KVEA
NEW
NEW
FHQ71CAVEB
Indoor unit
WALL MOUNTED TYPE
NEW
FCQ140KVEA
NEW
FHQ125CAVEB
FHQ100CAVEB
FHQ140CAVEB
NEW
Pair
NEW
FCQ125KVEA
FCQ100KVEA
FAQ71CVEA
Indoor unit
1 Phase, 220–230 V
DUCT CONNECTION
MIDDLE and HIGH STATIC
PRESSURE TYPE
NEW
FLOOR STANDING TYPE
NEW
Simultaneous Twin Multi
Indoor unit
NEW
NEW
FBQ50DAVET
Indoor unit
FAQ100CVEA
FBQ60DAVET
NEW
FVQ50CVE
FBQ71DAVET
NEW
FVQ60CVE
FBQ125DAVET
FBQ100DAVET
NEW
FVQ71CVEB
NEW
NEW
FVQ100CVEB
NEW
FVQ125CVEB
NEW
CEILING MOUNTED
CASSETTE TYPE
FBQ140DAVET
FVQ140CVEB
NEW
Round Flow
FCQ60KVEAX2
Indoor unit
NEW
DUCT CONNECTION
MIDDLE and HIGH STATIC
PRESSURE TYPE
FCQ71KVEAX2
NEW
FBQ60DAVETX2
Indoor unit
NEW
FLOOR STANDING TYPE
NEW
FVQ60CVEX2
Indoor unit
FBQ71DAVETX2
FVQ71CVEBX2
OUTDOOR UNIT
1 Phase, 220–230 V Outdoor unit
RZR50LVVM
RZR60LVVM
RZR100LVVM
RZR125LVVM
RZR140LVVM
FCQ100KVLT
FCQ125KAVLT
FCQ140KAVLT
Indoor unit
FBQ100DAVET
FBQ125DAVET
FBQ140DAVET
3 Phase, 220 V
Outdoor unit
RZQ100KCTLT
RZQ125KCTLT
RZQ140KCTLT
3 Phase, 380 V
Outdoor unit
RZQ100LUYLT
RZQ125LUYLT
RZQ140LUYLT
RZR71LVVM
NEW
CEILING MOUNTED
CASSETTE TYPE
1
Pair
3 Phase, 220V/380 V
Round Flow
Indoor unit
DUCT CONNECTION
MIDDLE and HIGH STATIC
PRESSURE TYPE
NEW
OUTDOOR UNIT
2
Full Lineup of Inverter Series
Daikin meets your needs with this full lineup of inverters
for various types of indoor units and power supplies.
100
125
4
Pair
CEILING SUSPENDED TYPE
3
WALL MOUNTED TYPE
FLOOR STANDING TYPE
1
CEILING MOUNTED CASSETTE TYPE
Round Flow
Twin
3.40
2.85
2
DUCT CONNECTION MIDDLE and
HIGH STATIC PRESSURE TYPE
3.60
3.57
Cooling*
CEILING MOUNTED CASSETTE TYPE
Round Flow
1 Phase, 220–230 V
4.30
140
FCQ50KVEA
RZR50LVVM
DUCT CONNECTION MIDDLE and
HIGH STATIC PRESSURE TYPE
FCQ60KVEA
RZR60LVVM
Cooling*
71
Cooling*
60
4.83
: Continuous
Cooling*
50
COP
Cooling*
34 new combinations added!
Achieved higher COP
Cooling*
: New Lineup
Energy saving
CEILING MOUNTED CASSETTE TYPE
Round Flow
Note :
*Rated cooling capacities are based on
the following conditions: Indoor temp.,
27°CDB, 19.0°CWB; outdoor temp.
35°CDB, 24.0°CWB. Equiv.
refrigeration piping, 7.5 m (horizontal).
DUCT CONNECTION MIDDLE and
HIGH STATIC PRESSURE TYPE
Comfortable
CEILING MOUNTED CASSETTE TYPE
Round Flow
DUCT CONNECTION MIDDLE and
HIGH STATIC PRESSURE TYPE
Enhanced comfort with Inverter
Simultaneous Twin Multi Operation
Comfortable currents of air
are sent to every corner of
the room.
For example, four indoor units
are judiciously spaced in this wide
single-floor restaurant to deliver comfortable
currents of air to every corner of the room.
Inverter performs variable control of frequency, which determines air
conditioner’s power performance.
At startup, full power is used to achieve the set temperature
quickly. Then, the capacity is adjusted according to the outdoor
temperature changes and subtle indoor load changes to
achieve fine capacity control resulting in a more stable room
temperature.
Non-inverter type air conditioners must be switched on
and off repeatedly, causing large fluctuations
of the room temperature.
At startup, inverter
raises frequency
smoothly, eliminating
the starting current
spike.
Non-inverter
Current
Pair
Pair
3 Phase,
220 V
COP is equal to capacity (kW) divided by power consumption (kW), and the larger the COP value, the higher the energy
efficiency, enabling cooling and heating with less electricity and increasing the energy saving performance.
3 Phase,
380 V
Round Flow
(1 Phase, 220–230 V)
FCQ71KVEA FCQ100KVEA FCQ125KVEA FCQ140KVEA
RZR71LVVM RZR100LVVM RZR125LVVM RZR140LVVM
What is COP (Coefficient of Performance)
FLOOR STANDING TYPE
CEILING MOUNTED
CASSETTE TYPE
Cooling operation
Temp
Starting current
Running
current
Inverter
Cools a room
in less time
Refrigerant branch
piping kit for Twin Multi
operation
Time
Current
Set temp
Small temp.
difference
Time
Inverter power control
Non-inverter type air conditioner
Running current
Time
2 sets of Twin Multi
3
4
CEILING MOUNTED CASSETTE TYPE
Round Flow
Cassette air conditioner with 360°
uniform airflow sets the standard
Avoids uneven temperature and discomfort caused by drafts.
Comfort enhanced by Round Flow!
FCQ50/60/71/100/125/140K
360° airflow
Air movement is gentle with Round Flow
With uniform temperature
distribution
Enhanced Comfort
360° airflow can
maintain comfort
even if air
discharge speed is
lower.
Airflow
distribution
Creates uniform
comfort throughout
the space
If you raise the set
temperature by 1 to
1.5°C,and velocity is
decreased by 25%,
you still obtain the same
feeling temperature and
comfort.
Greater comfort
Improved energy saving
Option
Accessory required for indoor unit
Navigation Remote Controller
Adapts easily to the installation space.
(Wired Remote Controller)
Because air flows out from corner outlets, comfort spreads more widely.
BRC1E62
Typical flow patterns
Note: Remote controller
cable not included.
Cables must be
procured locally.
Wireless LCD remote
controller
A signal receiver must be added to the indoor unit.
There are a total of 23 flow patterns.
All-round flow
3-way flow
(E.g., installed in
middle of ceiling)
(E.g., installed
near a wall)
L-shaped
2-way flow
(E.g., installed in
a corner)
Opposite
2-way flow
(E.g., installed in
a long room)
4-way flow also possible.
BRC7F633F
Note: Whatever the discharge direction, the same type of panel is used. If installing for other than all-round flow, an air discharge outlet sealing material (option) must be used to
close each unused outlet.
Operation sound increases when using 2-way or 3-way flow.
Signal
receiver unit
(Installed type)
Grime prevention and bactericidal coating: Make cleaning easier.
Wireless remote controller
and signal receiver unit are
sold as a set.
External panels are treated with a coating that
Treated
Untreated
repels dirt.
surface
surface
Features
*1Applicable when wired remote controller is used
*2For the outdoor units
*3Applicable when BRC1E62 is used
*4Applicable when BRC1C61 is used
5
• • •
*2
• • •
*2
• • • • • • • • • • • •
Others
Anti corrosion treated
heat exchangers
Ultra long-life filter
Fresh air intake kit
High-efficiency filter
Options
DIII-NET communication
standard
Interlock control
Central remote control
Control by 2 remote
controllers
Group control by 1 remote
controller
External command
control
Auto-restart
Self-diagnosis function
Control features
Emergency operation
Low gas pressure
detection
*4
Ceiling soiling prevention
*3
Filter sign
On/Off timer
*3
Long-life filter
Off timer (programmed)
*3
Pre charged for
up to 30 m
Weekly schedule timer
*3
Drain pump mechanism
Setpoint range set
*2
Silver ion anti-bacterial
drain pan
Setpoint auto reset
*1
Work & Servicing
Cleanliness
Anti-bacterial air filter
Night quiet operation
• • • • •
Remote controller
Two selectable
temperature-sensors
High ceiling application
Programme "Dry"
Switchable fan speed
(2 step)
Swing pattern selection
Auto swing
Comfort
*2
To prevent dirt sticking to the
external panels, they have
been coated with a surface
treatment.
Resists
soiling
Grimy
surface
• Condition after exposure
to the smoke of 600
cigarettes in 1 m3
enclosed space.
Silver ion anti-bacterial
drain pan
Non-flocking flaps
Filter has anti-mould and
bactericidal treatment
Mould-proof drain pan includes a silver ion
antibacterial agent that assists in
preventing the growth of slime, bacteria,
and mould that cause smells and clogging.
Condensation does not easily form on
and dirt does not cling to non-flocking
flaps.
It is easy to clean.
Prevents mould and microorganisms
growing out of the dust and moisture
that adheres to the filters.
6
CEILING MOUNTED CASSETTE TYPE
Fine square panels
Compact body and quiet operation
mm
95
0m
Indoor unit
High
Low
50K
60K
71K
100K
125K
140K
35
35
35
43
44
44
28
28
28
32
34
36
Same for
all models
m
Optimal comfort and convenience
assured by air discharge modes
Note: Air direction is set to the standard position when the unit is shipped from the factory.
The position can be changed from the remote controller.
Air direction
Standard setting
Setting to prevent soiling of ceiling*
Desired
situation
Standard position to
prevent draft.
Recommended for shops with
light coloured ceilings that
must be kept spotless.
Note : Anechoic chamber
conversion value, measured
according to JIS parameters
and criteria. During
operation these values are
somewhat higher owing to
ambient conditions.
Quick and easy to install
5-levels
air direction
setting
Auto-swing between
15° and 60°
Auto-swing between
25° and 60°
Settable to 5 different
levels between 25° and 60°
Settable to 5 different
levels between 15° and 60°
The air direction is set automatically to the
memorised position of the previous air direction.
Auto air
direction control
*Closing of the corner discharge outlets is recommended.
Suitable for high ceilings
Even in spaces with high ceilings, a comfortable airflow is carried down to
the floor level.
Criteria for ceiling height and number of air discharge outlets
(Ceiling height is reference value)
Number of air discharge outlets used
Standard
Ceiling
High ceiling
height
High ceiling
50K–71K
100K–140K
All round 4-way 3-way 2-way
flow
flow
flow
flow
All round 4-way 3-way 2-way
flow
flow
flow
flow
2.7 m 3.1 m 3.0 m 3.5 m
3.0 m 3.4 m 3.3 m 3.8 m
3.5 m 4.0 m 3.5 m -
3.2 m 3.4 m 3.6 m 4.2 m
3.6 m 3.9 m 4.0 m 4.2 m
4.2 m 4.5 m 4.2 m -
The condition of the drain pan and
drain water can be checked by
removing the drain plug and
intake grille.
256 mm *1
266 mm *2
Easy height adjustment
Each corner of the unit has an Adjuster Pocket that
lets you easily adjust the unit's suspended height.
Note: If the wireless remote control option is installed, a light receptor
unit is housed in one of the adjuster pockets.
All models can be installed without
using lifter because of the light weight.
Installable in
any direction
Since the orientation of
the intake grill can be
adjusted after installing,
the direction of the intake
grill lines can be unified
when multiple units
are installed.
Drain pump is equipped as standard
accessory with 850 mm lift.
Both indoor unit and wired remote controller (option (BRC1D61,BRC1E62) ) contain
temperature- sensors. Temperature sensing can be set at the unit or, to
further improve comfort level, closer to the target area at the wired remote
control. This feature must be set during commissioning by the technicians.
*Temperature-sensor on indoor unit must be used when the air conditioner is controlled from another room.
**Wireless remote controller does not have a temperature-sensor.
Switchable fan speed: High/Low
High setting provides maximum reach while low
setting minimises drafts.
On/Off timer
Operation starts when the preset time of the ON timer elapses and stops
when the preset time of the OFF timer elapses.
7
Drain plug
Options required for specific operating environments
Ultra long-life filter
Panel spacer
Even in smoky environments where
the air conditioning is on most of
the time, the ultra long-life filter only
has to be changed once a year.
Use when only minimal space is available between drop
ceilings and ceiling slabs.
Smoky atmosphere: annual filter change
*For dust concentration of 0.3 mg/m3 (Requires separately sold Air Cleaner.)
1 year (Approx. 5,000 hr) 15 hr/day x 28 day/month x 12 month/year
40mm
Ordinary store or office: filter change every 4 years
Panel spacer
*For dust concentration of 0.15 mg/m3
4 years (Approx. 10,000 hr) 8 hr/day x 25 day/month x 4 years
Note: Some ceiling constructions may hinder installation.
Contact your Daikin Dealer before installing your unit.
High-efficiency filter
Available in two types: 65% and 90% colorimetry.
Sealing material of air discharge outlet
Fresh air intake kit
Using this kit, a
duct can be fitted
to increase the
intake of outdoor
air.
Outside
A round duct can be attached without the need for a chamber.
Chamber type
(without T-joint pipe and fan)
850 mm
175 mm
Because the drain socket is
transparent, after the drain piping
has been installed, it is easy to
check if the drain come out
through the socket.
A flanged port for direct connection of a round duct is
provided. An existing branch duct chamber can also be fitted
(square slit hole).
The units can be installed in the following different ways.
Chamber type
(with T-joint pipe and without fan)
KDDP55B160
Transparent drain socket
Sealing material block air discharge openings not used in
2-way or 3-way blow.
Branch duct (direct-connection round duct)
Note: *Connecting ducts, insect nets, fire dampers, air filters, and other
parts should, as required, be procured locally.
**Outside Air fan interlocked with air conditioning unit is necessary.
Optional PCB(KRP1C63)is required for interlocking.
***It is recommended that the volume of outdoor air introduced
through the kit is limited to 10% of the maximum airflow rate of the
indoor unit. Introducing higher quantities will increase the
operating sound and may also influence temperature sending.
Note: Factory settings are for standard ceiling height and all-round flow.
High ceiling settings (1) and (2) are set with the remote controller by field setting.
Two selectable temperature-sensors
e
en th !
p
o
t
e
Jus ke grill
inta
With Ultra long-life filters (option), maintenance is not required in normal shops or offices
for up to four years.
Just 256 mm high. Installable in tight
ceiling spaces (50K-71K)
*1 298 mm high with 100K–140K
*2 308 mm high with 100K–140K
Auto-swing
Easier to maintain
dB(A)
Panel size is same for all models, FCQ50-140K.
It is easy to maintain a neat appearance when
multiple units are installed.
950
Round Flow
KDDP55B160K
Flexible duct
(procured locally)
Flexible duct
T-joint pipe
(procured locally)
T-joint pipe
Suction
chamber
Intake duct
Connection (procured locally)
chamber
(duct length: 4 m max.)
Suction
chamber
Intake duct
Connection (procured locally)
chamber
(duct length: 4 m max.)
Direct installation type
KDDP55X160
Duct flange
(with insulation
material)
Intake duct
(procured locally)
Note: Use of options will increase operating sound.
Connection to a centralised control
system is available without option
Low gas pressure detection
8
CEILING SUSPENDED TYPE
Comfortable airflow travels
throughout the room
NEW
The latest stylish
model
Sophisticated
design
Flexible installation
The unit fits more snugly
into tight spaces.
Flap neatly closes
when not in use.
FHQ71/100/125/140CA
Installation flexibility for
freedom of design
30 mm
30 mm
or more
or more
*Water used in the test-run can now be drained from the
air discharge opening rather than from the side as was
formerly the case.
Fresh white colour.
Drain pump kit (option) can
be easily incorporated
Drain pipe connection can be done
inside the unit. refrigerant and drain
pipe outlets are at the same opening.
Comfortable
The technology of the DC fan motor, wide
sirocco fan, and large heat exchanger
combine for greater airflow and quiet
operation. High/Middle/Low : 46/42/38 db(A)
Auto swing (up and down) and louvers
(left and right by hand) bring comfort to
the room
Option
Accessory required for indoor unit
Navigation Remote Controller
BRC1E62
Drain pump kit
(built inside
main unit)
Connection to a centralised control system is
available, without option.
All wiring and internal servicing can be done
from under the unit
Pipes more easily rigged
Easy maintenance
Installable on ceilings
4.3 m high
Note: Remote controller
cable not included.
Cables must be
procured locally.
mm
Low gas pressure detection
Louver manually
adjusts for straight
or wide angle airflow
(Wired Remote Controller)
600
Long-life filter lasts up to 6 months*
* For dust concentration of 0.15 mg/m3
Two time settings (2500 hrs and 1250 hrs) are available to match the installation
environment. Maintenance time warning is displayed on the remote controller (filter
sign).
Two selectable temperature-sensors
Wireless LCD remote
controller
Both indoor unit and wired remote controller (option (BRC1E62) )
contain temperature- sensors. Temperature sensing can be
set at the unit or, to further improve comfort level, closer to
the target area at the wired remote control. This feature
requires initial setting by the installer.
A signal receiver must be added to the indoor unit.
BRC7GA56
*Temperature-sensor on indoor unit must be used when the air conditioner is
controlled from another room.
**Wireless remote controller does not have a temperature-sensor.
Wireless remote controller and
signal receiver unit are sold as
a set.
("Auto" is applicable when BRC1E62 is used.)
Easy-clean, flat surfaces
Programme "Dry"
Features
9
•
•
*3
• • • • • • • • •
•
Anti corrosion treated
heat exchangers
Fresh air intake kit
DIII-NET communication
standard
Options Others
Interlock control
Central remote control
External command
control
*3
Group control by 1 remote
controller
*5
Control by 2 remote
controllers
*4
Auto-restart
Off timer (programmed)
*4
Control features
Self-diagnosis function
Weekly schedule timer
*4
Emergency operation
Setpoint range set
*4
Low gas pressure
detection
Setpoint auto reset
*3
Filter sign
Night quiet operation
*2
Pre charged for
up to 30 m
Two selectable
temperature-sensors
*1
Work & Servicing
Drain pump mechanism
High ceiling application
Programme "Dry"
Switchable fan speed
(3 step)
Auto swing
• • •
*1Installable on max. 4.3 m high ceiling
*2Applicable when wired remote controller is used
*3For the outdoor units
*4Applicable when BRC1E62 is used
*5Option
Anti-bacterial air filter
Remote controller Cleanliness
Comfort
Non-flocking flap
Condensation does not easily form on and
dirt does not cling to non-flocking flap.
Non-flocking flap
It is easy to clean.
Switchable fan speed:
High/Middle/Low and Auto
Signal receiver unit (Installed type)
Drain pump kit (option) includes a silver ion
antibacterial agent that assists in preventing
the growth of slime, bacteria, and mould that
cause smells and clogging.
*3
Dehumidification is a microprocessor controlled to prevent
abrupt and uncomfortable changes in air temperature.
Oil resistant grille
Quiet operation
Oil-resistant plastic is used for the air suction grille. This satisfies
durability in restaurants and other similar environments.
dB(A)
Indoor unit
High
Middle
Low
71CA
38
42
44
46
36
38
41
42
34
34
37
38
100CA
125CA
140CA
Note : Anechoic
chamber conversion
value, measured
according to JIS
parameters and criteria.
During operation these
values are somewhat
higher owing to ambient
conditions.
Note: Intended for use in salons, dining rooms, and ordinary sales floors, this specification
is not suitable for kitchens or other harsh environments.
10
WALL MOUNTED TYPE
Compact design and
easy installation
NEW
Easy installing and
servicing
Compact &
Sophisticated design
FAQ100
FAQ71/100C
9kg lighter
340
mm
FAQ71C
1,200mm
370mm shorter
FAQ100BV FAQ100C
Height
360mm
340mm
Width
1,570mm
1,200mm
Depth
200mm
240mm
Weight
26kg
17kg
Left pipe
Back-left pipe
Bottom-left pipe
Back-right pipe
Right pipe
Bottom-right pipe
Maintenance possible from the front
of the unit
Flaps neatly close when not
in use
FAQ100C
6-direction piping offers
greater installation
flexibility.
All maintenance tasks can be carried out via front
access. During service work, attachment and
detachment of parts is easier.
Drain pump kit is available as option.
Installs onto side of unit.
Comfortable
Option
Accessory required for indoor unit
Auto swing (up and
down) and
wide-angle louvers
(left and right by
hand) facilitate
even room
temperature
Navigation Remote Controller
(Wired Remote Controller)
BRC1E62
Note: Remote controller
cable not included.
Cables must be
procured locally.
An air discharge
modes ensure
comfortable air
distribution across
the entire room
Wireless LCD remote
controller
A signal receiver must be added to the indoor unit.
Height of drain up
Refrigerant
piping
1,000 mm
Wide-angle
louvers
(by hand)
Drain pump kit
Drain pump kit can be installed
on either left and right side of
the air conditioner.
Soft material
louver bends
airflow over a
wider area
Auto-swing
5-level air direction setting
Gettable to 5
different levels
BRC7EB519
Comfort even on the far side of the room
Wireless remote controller and
signal receiver unit are sold as
a set.
•
•
*3
• • • • • • • • •
Anti corrosion treated
heat exchangers
DIII-NET communication
standard
Others
Interlock control
Central remote control
External command
control
Group control by 1 remote
controller
*3
Control by 2 remote
controllers
*5
Auto-restart
*4
Control features
Self-diagnosis function
*1
Emergency operation
*1
Low gas pressure
detection
On/Off timer
*1
Filter sign
Off timer (programmed)
*1
Pre charged for
up to 30 m
Weekly schedule timer
*3
Drain pump mechanism
Setpoint range set
*2
Mould-proof air filter
Setpoint auto reset
• •
*1Applicable when BRC1E62 is used
*2Applicable when wired remote controller is used
*3For the outdoor units
*4Applicable when BRC1C61 is used
*5Option
Work & Servicing
Cleanliness
Night quiet operation
Programme "Dry"
Remote controller
Two selectable
temperature-sensors
*1
High fan speed mode
Auto airflow rate
Switchable fan speed
(3 step)
Comfort
Auto swing
Easy cleaning
Removable and washable grille
Flat panel, easy to wipe dust off
Features
11
Connection to a centralised control
system is available without option
To carry air to the far side of long
rooms, extra-high airflow adds 10%
more fan speed the "high" setting.
Air discharge strength is selected
from the remote controller by field
setting.
Signal receiver unit (Installed type)
• •
Indoor unit
Two selectable temperature-sensors
Switchable fan speed: High/Middle/Low
Non-flocking flaps
Condensation does not easily form on and dirt does not
cling to non-flocking flaps.
It is easy to clean.
Auto airflow rate (When BRC1E62 is used)
*3
Programme "Dry"
Dehumidification is microprocessor controlled to prevent abrupt and
uncomfortable changes in air temperature.
12
DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE
Enhance comfort using cleverly
placed ducts
Increased freedom of
design thanks to variable
control over external
static pressure
FBQ50/60/71/100/125/140DA
Comfort airflow achieved in accordance with
conditions such as duct length.
Using a DC fan motor, the external static pressure can be
controlled within a range of 50 Pa to 200 Pa.
When testing standard integrated ceiling units that employ duct
work, much time used to be required to adjust airflow to the right
level. Thanks to the ability provided by Daikin to automatically
perform this troublesome adjustment using a remote controller,
this step is now quick and easy. (Adjust by H tap .)
1. Adjust to approximately ±10% of the rated H tap airflow.
2. Once actual operation has begun, adjustment of the rated airflow is not possible.
Easier connection with the centralised
control system
dB(A)
200 Pa
Set to low static
pressure when ducts
are short.
Option
Use remote controller to adjust airflow
Quiet operation
Freely control external static pressure
50 Pa
Reduced installation time
Set to high static pressure for
advanced needs such as when
using dampers and long ducts.
High
Low
50/60/71DA
37
32
100DA
38
33
125/140DA
40
36
Note : Anechoic chamber conversion value, measured according to JIS parameters and criteria.
During operation these values are somewhat higher owing to ambient conditions.
Accessory required for indoor unit
Easy maintenance
Navigation Remote Controller
(Wired Remote Controller)
Thin, lightweight indoor
unit makes delivery and
installation easy.
BRC1E62
Note: Remote controller
cable not included.
Cables must be
procured locally.
With a height of only 300 mm, installation is
possible even in buildings with narrow ceiling
spaces.
Wireless LCD remote
controller
Clean
Silver ion anti-bacterial drain pan
Mould-proof drain pan includes a silver ion antibacterial agent
that assists in preventing the growth of slime, bacteria, and mould
that cause smells and clogging.
Comfortable
A signal receiver must be added to the indoor unit.
300mm
BRC4C64
Maintenance is easy because the drain pan can be removed.
Two selectable temperature-sensors
Signal
receiver unit
(Separate type)
Indoor unit
50/60/71DA
Height (mm)
Wireless remote controller
and signal receiver unit are
sold as a set.
Width
(mm)
Depth
(mm)
Machine weight (kg)
100DA
125/140DA
300
1,000
1,400
700
36
Both indoor unit and wired remote controller (option) contain
temperature- sensors. Temperature sensing can be set at the unit
or, to further improve comfort level, closer to the target area at the
wired remote control.
This feature requires initial setting by the installer.
*Temperature-sensor on indoor unit must be used when the air conditioner is controlled from another
room.
**Wireless remote controller does not have a temperature-sensor.
46
Emergency operation
Self-diagnosis function
Auto-restart
Control by 2 remote
controllers
Group control by 1 remote
controller
External command
control
Central remote
control
Interlock control
DIII-NET communication
standard
High efficiency filter
Anti corrosion treated
heat exchangers
*2
*3
*3
*3
*4
*5
•
*2
*5
•
Low gas pressure
detection
•
*3
Filter sign
•
*2
Long-life filter
•
Anti-bacterial air filter
•
On/Off timer
•
Off timer (programmed)
•
Weekly schedule timer
•
Setpoint range set
•
Setpoint auto reset
•
*1
*1Applicable when wired remote controller is used
*2For the outdoor units
*3Applicable when BRC1E62 is used
*4Applicable when BRC1C61 is used
*5Option
13
•
Night quiet operation
Programme "Dry"
•
Work & Servicing
Two selectable
temperature-sensors
Switchable fan speed
(2 step)
•
Cleanliness
Pre charged for
up to 30 m
Remote controller
Comfort
Silver ion anti-bacterial
drain pan
Features
*2
Control features
Option Others
Simultaneous air conditioning of two rooms and ventilation grille (ventilation opening)
When air conditioning two rooms
simultaneously, the air discharged into each
room must be circulated back to the air
conditioner. To achieve this, a ventilation
duct should be installed for each room or one
of the indicated ventilation grilles should be
installed on the partitioning wall or under the
door between the rooms.
Door-installed
ventilation grille
Partitioning wall
Wall-installed
ventilation grille
Under-door cutout
Ventilates air through
the partitioning wall.
(See right)
Ventilation grille
Ventilation grille
Under-door cutout
Note: The under-door cutout method should be used only when there is a small volume of airflow.
14
Floor Standing Type
New airflow control for
more comfort
New comfortable airflow control
1) Left and right directions (by remote controller)
Auto swing direction is selectable from 3 patterns to suit the layout of the room.
Pattern 1
Wide swing toward the front
Pattern 2
Swing on the left side
Pattern 3
Swing on the right side
FVQ50/60/71/100/125/140C
NEW
When installed in the center of a wall.
When installed in the corner of a room.
2) Up and down directions (by hand)
Independent up-and-down airflow directions facilitate even room temperature and help save energy.
Freely select
both up and
down airflow
direction with
8-louver
(horizontal
blade)
operation.
BRC1E62
can be
incorporated
into the
main unit.
Example applications
New unit
Upper louver (1)
Lower interlocking louvers (2)
Lower louver (1)
Each set of louvers to
can be independently
adjusted. (Manual adjustment)
Comfortable fan speed
control
Option
Switchable fan speed:
High/Middle/Low and Auto
Accessory required for
indoor unit
("Auto" is applicable when BRC1E62 is used.)
Navigation Remote Controller
Airflow rate is automatically controlled in accordance with the
difference between room temperature and set temperature.
High fan speed mode (applicable for FVQ50-100)
Note: Remote controller
cable not included.
Cables must be
procured locally.
To carry airflow to the far side of the room, airflow rate can be
increased 5% or 10% depending on the installation condition or
customer's request. (Field setting by remote controller.)
Programme "Dry"
Dehumidification is microprocessor controlled to prevent abrupt
and uncomfortable changes in air temperature.
Features
*1Applicable when BRC1E62 is used
*2Applicable for FVQ50-100
*3For the outdoor units
*4Applicable when BRC1C61 is used
15
•
*3
• •
*3
• • • • • • • • •
Anti corrosion treated
heat exchangers
DIII-NET communication
standard
Others
Interlock control
Central remote control
External command
control
Group control by 1 remote
controller
Control by 2 remote
controllers
Auto-restart
Control features
Self-diagnosis function
*4
Emergency operation
*1
Low gas pressure
detection
On/Off timer
*1
Filter sign
Off timer (programmed)
*1
Long-life filter
Weekly schedule timer
*1
Pre charged for
up to 30 m
Setpoint range set
*3
Anti-bacterial air filter
Setpoint auto reset
• •
Night quiet operation
*2
Two selectable
temperature-sensors
High fan speed mode
*1
Programme "Dry"
Auto airflow rate
Switchable fan speed
(3 step)
Independent up-and-down
airflow
Auto swing
• • •
Work & Servicing
Cleanliness
Quiet operation
dB(A)
Indoor unit
50/60/71C
100C
125C
140C
High
43
50
51
53
Middle
41
47
48
51
Low
38
44
46
48
Auto airflow rate is selectable.
BRC1E62
Remote controller
Turning louvers
and upward
and leaving
and horizontal
will reduce
uneven room
temperature.
Note : Anechoic chamber conversion value, measured according to JIS parameters and criteria.
During operation these values are somewhat higher owing to ambient conditions.
(Wired Remote Controller)
Comfort
When cooling
Upper interlocking louvers (4)
Energy saving
A DC fan motor improves efficiency.
Quick and easy installation
and maintenance
Lightweight indoor unit
Enables smooth transport and installation of the indoor unit.
Indoor unit
50/60/71C
Weight
39
100C
125C
(kg)
140C
47
Long-life filter lasts about 1year *
maintenance not required
* For dust concentration of 0.15 mg/ m3
Employs a safety lock function of suction grill.
*3
The grill will not open even upon impact.
Easier connection with the centralised control
system.
16
OUTDOOR UNIT
Technology for energy efficiency
New Compact Outdoor unit
RZR100LVVM
Easy installation and maintenance
Energy saving
Pre charged for up to
30 metres
4-direction piping offers greater
layout freedom (RZR/RZQ100-140 only)
If refrigerant piping length does not
exceed 30 m, there is no need for
on-site gas charging.
The outer panel for the
piping connection part of the
front, right side and
backside can be removed
and is easier for
post-installation piping work.
Through use of a V-cut
propeller fan that imitates
the efficiency of the swan, a
migratory bird, airflow
becomes smooth and loss is
reduced.
Long piping length
Allowed refrigerant piping length
and level difference
70 m
50 m
Max. length (Equivalent
length 70m) (Equivalent length 90m)
Max. level
difference
Conventional
NEW
(RZQ71KC)
(RZR71LV)
770 mm
Weight
68 kg
NEW
(RZQ100KC)
(RZR100LV)
Weight
1,170 mm
98 kg
Reduced by
175 mm
mm
RZQ71KCVLT
Reduced by
25 kg
RZR71LVVM
AC motor
30
60
90
120
Large load
High capacity
Note: Data are based on studies conducted under
controlled conditions at a Daikin laboratory.
990
990 mm
78 kg
Reduced by
20 kg
mm
The Automatic night quiet mode will initiate 8 hours after the peak temperature is reached in
the daytime, and normal operation will resume 10 hours after that.
Sound level (dB(A))
Rated
Night Quiet Mode
RZR50/60/71LV
48
44
RZR100LV
RZQ100/125/140KC
RZQ100LU
49
45
RZR125LV
RZQ125/140LU
50
45
RZR140LV
50
46
Note : 1Anechoic chamber conversion value, measured according to JIS
parameters and criteria. During operation these values are
somewhat higher owing to ambient conditions.
2
Value when cooling. Value will differ when heating.
22:003
8:003
100
8 hours
50
Load (%)
Operation
Sound4 (dB(A))
1
Capacity (%)
Peak in outdoor temperature
10 hours
Use of an optimised sine wave
smoothes motor rotation, further
improving operating efficiency.
Sine wave DC inverter
RZR50/60/71/100LV
>> Swing compressor
As the bottom frame is subject to
corrosion, corrosion-proof galvarium steel
plate is adopted to enhance the durability.
Energy savings is
realised, eliminating
the friction and the
leakage of
refrigerant gas.
Heat exchange fins provided with
anti-corrosion treatment
Non-treated fin
Aluminium
Anti corrosion
treated heat
exchangers
Hydrophilic film
Aluminium
Corrosion resistant
acrylic resin
2
Swing bushing
Refrigerant gas
Piston by incorporated
blade and roller.
RZR125/140LV, RZQ100/125/140KC, RZQ100/125/140LU
Sucked gas is compressed in the
scrolling part before the heated motor,
so that the machine compress
the non-expanded gas, resulting Discharge
in high efficiency compression.
Smooth Air Inlet Bell Mouth and Aero Spiral Fan
(RZR/RZQ100-140 only)
With the bent
blade edge
Scroll section
Motor section
Without the bent
blade edge
These two features work to reduce noise. Guides
are added to the bell mouth intake to reduce
turbulence in the airflow generated by fan suction.
The Aero Spiral Fan features fan blades with the
bent blade edges, further reducing turbulence.
Escaping eddies are sucked in by
the bent blade edges, reducing
overall turbulence.
(RZR/RZQ100-140 only)
The maximum capacity is
maintained within a set level of
power consumption, which makes it
possible to keep comfort and
effective demand control.
Suction
>> The structural scroll
3
DC fan motor
Efficiency improved in all areas compared to AC
motors, especially at low speeds.
DC fan motor structure
Limitation
0
49
Power
consumption
Reducing noise will reduce capacity slightly.
>> Smooth sine wave DC inverter
Imitating the performance
of the swan
Demand Control
Function
RZR100LVVM
Night time quiet operation function
2
*1. A neodymium magnet is approximately 10 times stronger
than a standard ferrite magnet.
*2. The torque created by the change in power between the iron
and magnet parts.
Construction
Reduced by
180 mm
RZQ100KCVLT
17
70
Small load
Low capacity
Durability
595
595 mm
43 kg
Conventional
Height
Conventional
DC motor
More than 20%
Rotational speed (rps)
Effective gas monitoring reduces the labor required
for operation, maintenance, and repairs.
Comparison of outdoor units
Height
80
0
Low gas pressure detection function
Reduced installation work thanks to
light, compact outdoor unit.
1
50
30 m
Compact and lightweight
2
Reluctance
DC motor
Reluctance DC Motor
90
*Pump-down function is available for pre-charged refrigerant amount.
Note : 1Additional refrigerant charging is
required if the refrigerant pipe is
longer than the length.
3
60
(Refrigerant recovery function)
A pump-down switch is provided to make it easier to
collect refrigerant if the unit is to be moved or layout
modified.
30 m
Compressor equiped with Reluctance DC motor
Daikin DC Inverter models are equipped with the Reluctance DC
motor for compressor.
The Reluctance DC motor uses 2 different types of torque,
neodymium magnet*1 and reluctance torque*2.
This motor can save energy because it generates more power with a
smaller electric power than an AC or conventional DC motor.
Φ550
V-cut propeller fan
Facilitates pump down
RZR50-140LV RZQ100-140KC/LU
Pre charged1
Separation
available
1
Motor efficiency (%)
RZR50LVVM
RZR60LVVM
RZR71LVVM
The high efficiency compressor to
achieve a high COP
RZR125LVVM
RZR140LVVM
RZQ100KCTLT
RZQ125KCTLT
RZQ140KCTLT
RZQ100LUYLT
RZQ125LUYLT
RZQ140LUYLT
Rated
45 Quiet mode
8:00
12:00 16:00 20:00
Quiet mode
0:00
4:00
8:00
Note : 3In case of RZQ series, period selectable from 22-8:00, 22-6:00, and 20-8:00.
4
In case of RZR100
8:00
12:00
16:00
20:00 Time
* Required for KRP58M51 (Option)
18
LCD REMOTE CONTROLLER
Optional accessory
Easy-to-read LCD remote controller allows various system
control configurations and can control multiple indoor units.
Remote controller options are shown on the page introducing each indoor unit model.
Navigation Remote Controller
(Wired Remote Controller BRC1E62)
Wired LCD remote controller
Easy to read because of large LCD screen.
The rubber switch and the
oil-resistant plastic casing are
adopted for durability.
This simple, modern designed remote controller with fresh
white colour matches your interior design. Operation is
much easier and smoother, just follow the indications on
the navigation remote controller.
NEW
Only 17 mm thick. Can be
installed either recessed or
exposed.
Wired remote controller has
built-in temperature-sensor
(Applies to wired remote controllers (BRC1C61/1E62))
Enables temperature sensing closer to target
area for improved comfort. (When using remote
control from another room, temperature-sensor in
indoor unit's air inlet must be selected.)
Facilitates maintenance and repair
All initial settings can be set from the remote
controller. After interior construction is complete,
ceiling mounted cassette type can be remotely
set without having to use stepladder access for
manual setting.
BRC1C61
Setting contents: High ceiling use, air direction, filter type, address
Clear Display
LCD wireless remote controller
Dot matrix display
Backlight
display
A combination of fine dots
enables various icons.
Large text display is easy to
see.
Light receptor mounted type
The wireless remote controller is
supplied in a set with a signal
receiver.
Shape of signal receiver unit
differs according to the indoor
unit.
BRC7F633F
Energy saving
NEW
Setpoint auto reset
NEW
- Even if the set temperature is changed, it returns to the preset temperature
after apreset period of time.
- Period selectable from 30min/60min/90min/120min.
Restaurant sample
Restaurant opened
Temperature is set to 27ºC
Full tables at lunchtime
Then is lowered to 24ºC for
crowded room
27 °C
After 30 minutes*
Automatically returns to preset
temperature (27ºC)
Returns to
27 °C
24 °C
Setpoint range set
- Saves energy by limiting the
min. and max. set temperature.
- Avoids excessive heating or
cooling.
- This function is convenient when
the remote controller is installed
at a place where any number of
people may operate it.
Wireless remote
controller
Signal receiver unit
(For ceiling mounted
cassette type)
Remote controller is equipped with model name
and failure display functions. This facilitates
service in the unlikely event of a malfunction.
(Applies to wired remote controller (BRC1E62))
SkyAir shares common control with
Heat Reclaim Ventilator and the
other Daikin air-conditioning units,
thus simplifying interlocking
operations.
Easily adaptable to large-scale, high-function,
centralised remote control systems.
Installing and connecting control wiring between
SkyAir and other Daikin air-conditioning
equipment is easy.
Indoor units applicable for the remote controller
Signal receiver unit is contained inside decoration panel or indoor unit
CEILING MOUNTED CASSETTE TYPE
BRC7F633F
CEILING SUSPENDED TYPE
BRC7GA56
WALL MOUNTED TYPE
BRC7EB519
automatically
DUCT CONNECTION MIDDLE and
HIGH STATIC PRESSURE TYPE
Off timer (programmed)
Note: The signal receiver unit shown in the
photograph is for mounting inside
the decoration panel of the ceiling
mounted cassette type.
for centralised control (group control address is set automatically).
BRC4C64
*Setting possible for after 30, 60, 90, and 120
minutes.
- Sets and saves setting for an increment of time that automatically turns off air
conditioner after a preset period of time for each time operation starts.
- Period can be preset from 30 to 180 minutes in10-minute increments.
LCD panel shows operating status in letters, numbers, and motion.
Airflow / swing display
Preset temperature / operation mode display
Programming time display
Convenience
Weekly schedule
- 5 actions per day can be scheduled for each day
of the week.
- The holiday function will disable schedule timer
for the days that have been set as holiday.
NEW - 3 independent schedules can be set.
Self-diagnosis function
Displays auto-swing operating status and setting position of air discharge angle.
Displays preset room temperature and operating status (fan, dry, cool).
Operation start and stop time can be set for individual timers up to 72 hours. The LCD also shows
when it is time to clean the filter, when changeover is under centralised control, and ventilation/cleaning.
Monitors operating status within the system covering 40 items, and displays a message to indicate as soon as a malfunction occurs.
Multilingual display
Display is available in 11
languages.
(English, German, French, Spanish,
Italian, Portuguese, Greek, Dutch,
Russian, Turkish, and Polish).
(e.g. summer, winter, mid-season)
19
20
Simple system provides a diverse assortment LCD
of control
modes.
REMOTE CONTROLLER
Control pattern
Control by 1
remote controller
Wired remote controller
Wireless remote controller
Note: Some features only available on selected models. See model pages for full list of features applicable to each unit.
(Basic system)
Non-polar, double-core
(max. wiring length 500 m)
Control by 2
remote controllers
Abundance of functions that provide comfortable
air-conditioning in stores and offices.
Signal receiver unit installed
on indoor unit
Control by 1 wireless remote
controller and 1 wired remote
controller (See note 2, 3)
For control from 2
locations such as in
room and control room,
exits, etc.
Signal receiver unit installed
on indoor unit
Connects 2 wired remote
controllers (See note 1)
Comfort
Auto-swing
Delivers comfortable
air-conditioning to all areas, near
to and far from the air-conditioner.
Programme "Dry"
The air flow direction can be
fixed at your desited angle
by the remote controller.
Swing pattern selection
(standard, ceiling soiling prevention)
Group control
For simultaneous
control of up to 16
indoor units.
You can freely set 2 air discharge setting by remote controller.
Automatic address setting function
Automatic address setting function
Signal receiver unit installed
on 1 indoor unit
Control by
external command
Operation and
surveillance is carried out
using the contact signal
from the operation control
box in the building
surveillance (security)
room.
(2) Air direction in ceiling
soiling prevention
setting
Optional wiring adaptor for
electrical appendices is necessary
Optional wiring adaptor for
electrical appendices is necessary
Central remote controller (option)
Centralised remote
control
(1) Air direction in
standard setting
Central remote controller (option)
Centralised control of
up to 64 indoor groups
from remote location
up to 1 kilometer away.
Independent up-and-down airflow
Independently adjust (manually) the eight horizontal blade
louvers in both up and down directions to achieve an airflow
that reduces uneven room temperature.
Switchable fan speed
High setting provides maximum reach while low setting
minimises drafts.
Dehumidification is microprocessor controlled to prevent abrupt
and uncomfortable changes in air temperature. Useful for reducing
uncomfortable humidity without uncomfortable cooling of the room.
High-ceiling application
Delivers
air-conditioning
comfort all the
way down to the
floor in
air-conditioning
zones with high
ceilings.
Note:When units are installed on high ceilings, depending on the model,
various restrictions concerning maximum height, air discharge direction,
and choice of options may apply.
Two selectable temperature-sensors
Temperature-sensors are included in the indoor unit and
optional wired remote controller. Temperature sensing closer
to target area is possible to further increase the comfort level.
Use the temperature-sensor in the
indoor unit when controlling air
conditioning from another room.
Auto airflow rate
Heat Reclaim
Ventilator
Heat Reclaim
Ventilator
Link by remote
controller group control.
Interlock control
with Heat Reclaim
Ventilator
Can be operated simultaneously
or independently by remote controller
(set by ventilation mode)
Can be operated simultaneously
by remote controller
(set by ventilation mode)
Central remote controller (option)
Zone link control by
centralised control.
Central remote controller (option)
Heat Reclaim
Ventilator
Heat Reclaim
Ventilator
Heat Reclaim Ventilator for indoor units within
a zone are operated by interlocking Can also be
operated independently by remote controller.
Heat Reclaim Ventilator for indoor units within
a zone are operated by interlocking
Note: 1BRC1E62 can connect to BRC1E62 only.
2
It is not possible to use two wireless remote controllers.
3
BRC1E62 cannot connect to wireless remote controller.
Airflow rate is automatically controlled in accordance with the
difference between room temperature and set temperature.
High fan speed mode
You can increase fan speed approximately 10% higher than the
"high" setting.
Applicable for wall mounted type
Setpoint auto reset
Even if the set temperature is changed, it returns to the preset
temperature after a preset period of time.
Weekly schedule timer
control system.
DCS302CA61 (Option)
DCS301BA61 (Option)
The Automatic night quiet mode will initiate 8 hours after the
peak temperature is reached in the daytime, and normal
operation will resume 10 hours after that.
Off timer (programmed)
Sets and saves setting for an increment of time that
automatically turns off air conditioner after a preset period of
time for each time operation starts.
Setpoint range set
Easily adaptable to large-scale, high-function, centralised remote
Unified on/off controller
Night quiet operation
Remote Controller
Saves energy by limiting the minimum and maximum set
temperatures. Avoids excessive heating and cooling.
Central remote controller
Note: Wireless remote controllers have no
temperature-sensor.
Schedule timer
DST301BA61 (Option)
DCS601C51 (Option)
On/Off timer
Operation starts when the preset time of the ON timer elapses
and stops when the preset time of the OFF timer elapses.
Up to five operation ON/OFF settings can be programmed per
day for each day of the week. Not only can the time be set for
the operation ON setting, but also the temperature.
Cleanliness
Anti-bacterial air filter
The Air filter has a anti-bacterial treatment to help prevent the
growth of bacteria and mould on it.
Centralised control, with setting
as simple as it is with a standard
remote controller, of up to 64
groups (1,024 indoor units) is
possible.
21
Centralised control of on/off by
group or all at once for up to 256
indoor units.
Unified control of weekly
schedule for up to 1,024 indoor
units.
Schedule timer sets on/off time in 1 minute
units to be executed twice a day for a week
at a time.
With its high functionality, the full
colour “all-in-one” graphic
controller facilitates management
of SkyAir System in a variety of
ways.
Silver ion anti-bacterial drain pan
Mould-proof drain pan includes a silver ion antibacterial agent
that assists in preventing the growth of slime, bacteria, and
mould that cause smells and clogging.
Mould-proof air filter
Sanitary filter has mould-resistant treatment.
22
Note: Some features only available on selected models. See model pages for full list of features applicable to each unit.
CEILING MOUNTED CASSETTE TYPE
Work and Servicing
Drain pump mechanism
Steeper gradient realises more
efficient condensate drainage.
High-lift is especially useful for
long lengths of drain piping.
50
Ceiling soiling prevention function
Daikin's innovative air discharge mechanism keeps airflow
away from the ceiling. Ceiling cleaning is less frequently
required.
Low gas pressure detection
Pre charged for up to 30 metres
If refrigerant piping length does not exceed 30 m, there is no
need for on-site gas charging.
Long-life filter
Maintenance is not required for one year (two years when a
ceiling mounted cassette type is used).
SPECIFICATIONS
Model
Name
Power supply
Cooling capacity1,2
Rated (Min. - Max.)
Power consumption
COP
Indoor
unit
Insufficient gas charging is normally hard to detect. During
post-installation trials and regular inspection procedures, the
refrigerant level is monitored by microprocessor to maintain
proper gas pressure. Reliability is assured and maintenance
and inspection can be carried out more quickly.
If there is a malfunction elsewhere in the system, the fan or
compressor can still be operated.
Filter sign
The filter sign warns you when it is time to clean the filter.
*When using a wired remote controller the sign is displayed in the LCD.
When using a wireless remote controller the filter sign lamp illuminates on
the signal receiver unit.
The operating parameters of indoor and outdoor units, and
sensor data at critical locations throughout the system, are
constantly monitored using a microcomputer. To facilitate
quick response in the event of a malfunction, a message
appears on the LCD of the remote controller and an LED on
the unit illuminates.
If there is a power outage while the equipment is operating,
operations will restart in the same mode as before the power
cut when electricity is restored.
Control by 2 remote controllers
Using 2 remote controllers you can operate the equipment
locally or from a remote location.
Note: When a wireless remote controller is used, remote control by two remote controllers is
not possible.
Group control by 1 remote controller
You can turn up to 16 indoor units on/off with a single remote
controller. (When using connected indoor units, the settings
must all be the same and on/off will be simultaneous.)
Two types are available: 65% and 90% colorimetry.
Ultra long-life filter
Requires no maintenance for about 4 years* (10,000h) in
stores and offices.
*For dust concentration of 0.15 mg/m3
kW
W/W
5.0
(2.3-5.6)
6.0
(2.6-6.3)
7.1
(3.2-8.0)
1.03
4.87
1.40
4.30
1.99
3.57
2.78
3.60
Unit
Decoration panel
Certified Operation range Cooling
Colour
Type
Compressor
Motor output
Refrigerant charge (R-410A)
Cooling
Night quiet mode
Dimensions (HXWXD)
Machine weight
Certified Operation range Cooling
Liquid (Flare)
Piping
connections
Gas (Flare)
Drain
Indoor unit
Outdoor unit
m3/min
cfm
dB(A)
mm
21/13.5
741/477
35/28
256X840X840
mm
kg
kg
21
*Required for KRP58M51 (Option)
Central remote control
Optional central remote controller enables centralised control of
up to 1024 indoor units (64 groups) from up to 1 kilometer away.
kW
Hermetically sealed swing type
1.35
1.76
1.12
Cooling
Colour
Note: *Connecting ducts, insect nets, fire dampers, air filters, and other parts
should, as required, be procured locally.
**Outside Air fan interlocked with air conditioning unit is necessary. Optional
PCB(KRP1C63)is required for interlocking.
***It is recommended that the volume of outdoor air introduced through the kit
is limited to 10% of the maximum airflow rate of the indoor unit. Introducing
higher quantities will increase the operating noise and may also influence
temperature sending.
Cooling
Night quiet mode
Dimensions (HXWXD)
Machine weight
Certified Operation range Cooling
Liquid (Flare)
Piping
connections
Gas (Flare)
Drain
Indoor unit
Outdoor unit
Max. interunit piping length
Max. installation level difference
Heat insulation
21/13.5
741/477
35/28
256X840X840
21
2.4
2.03
Hermetically sealed scroll type
3.1
2.4
48
44
595X845X300
43
49
50
45
46
1,170X900X320
97
45
990X940X320
78
21 to 46
o/ 9.5
o/ 15.9
3.1
46
VP25 (I.D o/ 25XO.D o/ 32)
o/ 26.0 (Hole)
50 (Equivalent length 70)
30
100
125
140
100
125
140
FCQ100KVLT
FCQ125KAVLT
FCQ140KAVLT
FCQ100KVLT
FCQ125KAVLT
FCQ140KAVLT
RZQ100KCTLT
RZQ125KCTLT
RZQ140KCTLT
RZQ100LUYLT
RZQ125LUYLT
RZQ140LUYLT
10.0
(5.0–11.4)
3 Phase, 220V, 60Hz
12.5
(6.0–14.3)
13.3
(6.2–15.8)
10.0
(5.0–11.4)
3 Phase, 380V, 60Hz
12.5
(6.0–14.3)
13.1
(6.2–15.8)
2.77
3.61
3.47
3.60
3.91
3.40
2.77
3.61
3.51
3.56
3.85
3.40
----------
Unit
Decoration panel
Unit
Decoration panel
Certified Operation range Cooling
Colour
Type
Compressor
Motor output
Sound level3
You can provide air-conditioning with fresh air from outside.
Convenient for places where a ventilation fan cannot be installed.
kW
W/W
Refrigerant charge (R-410A)
Fresh-air intake kit
4.91
2.85
3.15
(Charged for 30 m)
mm
mm
m
m
kW
Machine
weight
Outdoor
unit
3.68
3.40
2.7
(Charged for 30 m)
Outdoor unit
Sound level (H/L)3
Unit
Dimensions
(HXWXD)
Decoration panel
DIII-NET communication standard
Standardly equipped interface enables connection to
centralised control system without need of an adaptor.
4.91
2.85
1.6
(Charged for 30 m)
dB(A)
dB(A)
mm
kg
°CDB
mm
mm
Outdoor unit
Airflow rate (H/L)
Enables interlocking control with external equipment such as
Heat Reclaim Ventilator.
14.0
(6.2-15.4)
14 to 25
Ivory white
kg
Indoor unit
Power supply
Cooling capacity1,2
Rated (Min. - Max.)
Power consumption
Interlock control
3.68
3.40
12.5
(5.7-14.0)
Both liquid and gas piping
Model
Name
COP
Indoor
unit
140
14.0
(6.2-15.4)
Fresh white
32/20
33/22.5
1,130/706
1,165/794
43/32
44/34
44/36
298X840X840
50X950X950
24
5.5
°CWB
External command control
Operation and surveillance is carried out using the contact signal from
the operation control box in the building surveillance (security) room.
125
----------
Unit
Decoration panel
Sound level3
140
1 Phase, 220–230 V, 60 Hz
10.0
12.5
(5.0-11.2)
(5.7-14.0)
Heat insulation
Options
High-efficiency filter unit
Cooling
Max. interunit piping length
Max. installation level difference
Control features
Auto-restart
kW
Colour
125
RZR50LVVM RZR60LVVM RZR71LVVM RZR100LVVM RZR125LVVM RZR140LVVM RZR125LVVM RZR140LVVM
Outdoor unit
Machine
weight
Self diagnosis function
100
Outdoor unit
Sound level (H/L)3
Unit
Dimensions
(HXWXD)
Decoration panel
Outdoor
unit
71
FCQ50KVEA FCQ60KVEA FCQ71KVEA FCQ100KVEA FCQ125KVEA FCQ140KVEA FCQ60KVEAx2 FCQ71KVEAx2
Airflow rate (H/L)
Emergency operation
60
Indoor unit
Fresh white
m3/min
cfm
dB(A)
mm
32/20
1,130/706
43/32
33/22.5
1,165/794
44/34
mm
kg
kg
°CWB
kW
1.9
14 to 25
Ivory white
Hermetically sealed scroll type
2.9
1.8
2.4
mm
mm
m
m
33/22.5
1,165/794
44/34
44/36
2.4
2.9
3.7
(Charged for 30 m)
kg
dB(A)
dB(A)
mm
kg
°CDB
mm
mm
32/20
1,130/706
44/36
43/32
298X840X840
50X950X950
24
5.5
49
50
45
1,170X900X320
101
99
-5 to 50
o/ 9.5
o/ 15.9
VP25 (I.D o/ 25XO.D o/ 32)
o/ 26.0 (Hole)
70 (Equivalent length 90 m)
30
Both liquid and gas piping
Note :
1
Rated cooling capacities are based on the following conditions: Indoor temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal).
2
Capacities are net, including a deduction for cooling for indoor fan motor heat.
3
Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions.
Others
Anti corrosion treated heat exchangers
To achieve increased durability by improved resistance to salt corrosion and atmospheric pollution, coated Anti corrosion treated heat
exchangers (with special acryl pretreatment) are used for the heat exchanger of the outdoor unit.
In high corrosive areas, regular maintenance needs to be carried out.
23
24
SPECIFICATIONS
CEILING SUSPENDED TYPE
Indoor unit
Model
Name
Outdoor unit
Power supply
100
125
140
FHQ71CAVEB
FHQ100CAVEB
FHQ125CAVEB
FHQ140CAVEB
RZR71LVVM
RZR100LVVM
RZR125LVVM
Cooling
Power consumption
COP
Colour
Indoor
Airflow rate (SH/H/L)
unit
Sound level (H/M/L)3
Dimensions (HXWXD)
Machine weight
Certified operation range
Colour
Type
Compressor
Refrigerant charge
(R-410A)
Motor
output
Refrigerant charge (R-410A)
Sound level3
Cooling
Night quiet mode
Dimensions (HXWXD)
Machine weight
Certified operation range
Piping
connections
Liquid (Flare)
Gas (Flare)
Drain
Indoor unit
Outdoor unit
Max. interunit piping length
Max. installation level difference
Heat insulation
kW
7.1
(3.2-8.0)
10.0
(5.0-11.2)
12.5
(5.7-14.0)
13.3
(6.2-15.4)
kW
W/W
2.37
3.00
3.03
3.30
4.01
3.12
4.68
2.84
m3/min
cfm
dB(A)
mm
20.5/17/14
724/600/494
38/36/34
235X1,270X690
32
28/24/20
988/847/706
42/38/34
31/27/23
1,094/953/812
44/41/37
235X1,590X690
38
34/29/24
1,200/1,024/847
46/42/38
Fresh white
kg
°CWB
kW
kg
dB(A)
dB(A)
mm
kg
°CDB
mm
mm
mm
mm
m
m
Hermetically sealed swing type
1.76
2.03
1.6
(Charged for 30 m)
2.7
(Charged for 30 m)
3.15
(Charged for 30 m)
48
44
595X845X300
43
49
50
45
46
990X940X320
78
1,170X900X320
97
21 to 46
o/ 9.5
o/ 15.9
VP20 (I.D o/ 20XO.D o/ 26)
o/ 26.0 (Hole)
50 (Equivalent length 70)
30
Both liquid and gas piping
Indoor unit
Outdoor unit
FAQ100CVEA
RZR71LVVM
Cooling1
kW
W/W
Colour
Airflow rate (H/M/L)
Dimensions (HXWXD)
Machine weight
Certified Operation range
Colour
Type
Compressor
Motor output
Refrigerant charge (R-410A)
Cooling
Sound level3
Night quiet mode
Dimensions (HXWXD)
Machine weight
Certified Operation range
Piping
Liquid (Flare)
connections
Gas (Flare)
Drain
Indoor unit
Outdoor unit
Max. interunit piping length
Max. installation level difference
Heat insulation
RZR100LVVM
1 Phase, 220–240 V, 50 Hz/220–230 V, 60 Hz
kW
Sound level (H/M/L)3
Outdoor
unit
FAQ71CVEA
Outdoor unit
COP
Indoor
unit
100
7.1
(3.2-8.0)
10.0
(5.0-11.2)
2.19
3.24
3.37
2.97
kW
kg
dB(A)
dB(A)
mm
kg
°CDB
mm
mm
mm
mm
m
m
18/16/14
635/565/494
45/42/40
290X1,050X238
13
14 to 25
Ivory white
Hermetically sealed swing type
1.76
1.6 (Charged for 30 m)
48
44
595X845X300
43
21 to 46
o/ 9.5
o/ 15.9
VP13 (O.D o/ 18 X I.D o/ 13)
o/ 26.0 (Hole)
50 (Equivalent length 70m)
30
Both liquid and gas piping
Note :
1
Rated cooling capacities are based on the following conditions: Indoor temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal).
2
Capacities are net, including a deduction for cooling for indoor fan motor heat.
3
Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions.
25
6.0
(2.6-6.3)
7.1
(3.2-8.0)
10.0
(5.0-11.2)
12.5
(5.7-14.0)
14.0
(6.2-15.4)
12.5
(5.7-14.0)
14.0
(6.2-15.4)
Cooling
kW
W/W
1.39
3.60
1.69
3.56
2.22
3.20
2.82
3.55
3.73
3.35
4.71
2.97
3.73
3.35
4.71
2.97
Cooling
m3/min
cfm
18/15
635/530
32/23
1,130/812
37/32
38/33
300X1,000X700
36
Hermetically sealed swing type
1.76
1.35
1.12
37/32
40/36
---------- 5
300X1,400X700
300X1,000X700
46
36
14 to 25
Ivory white
Hermetically sealed scroll type
2.9
2.03
2.4
2.4
2.9
1.6
(Charged for 30 m)
2.7
(Charged for 30 m)
3.15
(Charged for 30 m)
48
44
595X845X300
43
49
50
45
46
1,170X900X320
97
dB(A)
dB(A)
mm
kg
45
990X940X320
78
21 to 46
o/ 9.5
o/ 15.9
VP25 (I.D o/ 25XO.D o/ 32)
o/ 26.0 (Hole)
50 (Equivalent length 70)
30
Both liquid and gas piping
°CDB
mm
mm
mm
mm
m
m
46
100
125
140
100
125
140
Indoor unit
FBQ100DAVET
FBQ125DAVET
FBQ140DAVET
FBQ100DAVET
FBQ125DAVET
FBQ140DAVET
Outdoor unit
RZQ100KCTLT
RZQ125KCTLT
RZQ140KCTLT
RZQ100LUYLT
RZQ125LUYLT
RZQ140LUYLT
1 Phase, 220V, 60Hz
10.0
(5.0–11.4)
3 Phase, 220V, 60Hz
12.5
(6.0–14.3)
13.3
(6.2–15.8)
10.0
(5.0–11.4)
3 Phase, 380V, 60Hz
12.5
(6.0–14.3)
13.1
(6.2–15.8)
W/W
3.13
3.19
3.96
3.16
4.22
3.15
3.13
3.19
3.96
3.16
4.16
3.15
m3/min
cfm
32 / 23
1,130 / 812
kW
kW
Cooling
----------
Colour
Airflow rate
(H/L)
Cooling
External static pressure
(Middle-High)
4
Sound level Cooling (H/L)
Air filter
Dimensions (HXWXD)
Machine weight
Certified Operation range Cooling
39 / 28
1,377 / 988
dB(A)
Type
Motor output
Refrigerant charge (R-410A)
Sound level4 Cooling
Night quiet mode
38 / 33
40 /36
mm
kg
°CWB
Dimensions (HXWXD)
Machine weight
Certified Operation range Cooling
Liquid (Flare)
Piping
connections
Gas (Flare)
Drain
Indoor unit
Outdoor unit
Max. interunit piping length
Max. installation level difference
kW
kg
dB(A)
dB(A)
mm
kg
°CDB
mm
mm
mm
mm
m
m
39 / 28
1,377 / 988
32 / 23
1,130 / 812
50-200 3
Pa
Colour
Compressor
Heat insulation
18/15
635/530
39/28
1,377/988
50-200 3
Pa
Indoor unit
Outdoor unit
Cooling capacity1,2
Rated (Min. - Max.)
Power consumption
Outdoor
unit
2.03
2.7 (Charged for 30 m)
49
45
900X940X320
78
5.0
(2.3-5.6)
4
Power supply
26/23/19
918/812/671
49/45/41
340X1,200X240
17
140
kW
Cooling
Night quiet mode
Dimensions (HXWXD)
Machine weight
Certified Operation range Cooling
Piping
Liquid (Flare)
connections
Gas (Flare)
Indoor unit
Drain
Outdoor unit
Max. interunit piping length
Max. installation level difference
Heat insulation
Fresh white
m3/min
cfm
dB(A)
mm
kg
°CWB
125
1 Phase, 220 V, 60 Hz
1 Phase, 220–230 V, 60 Hz
Sound level4 Cooling (H/L)
dB(A)
Air filter
mm
Dimensions (HXWXD)
kg
Machine weight
Certified Operation range Cooling
°CWB
Colour
Type
Compressor
Motor output
kW
Refrigerant charge
kg
(R-410A)
Fan
140
----------
Sound level
COP
Indoor
unit
125
RZR50LVVM RZR60LVVM RZR71LVVM RZR100LVVM RZR125LVVM RZR140LVVM RZR125LVVM RZR140LVVM
Airflow rate
(H/L)
Model
Name
71
100
Outdoor unit
External static pressure
(Middle-High)
Outdoor
unit
71
FBQ50DAVET FBQ60DAVET FBQ71DAVET FBQ100DAVET FBQ125DAVET FBQ140DAVET FBQ60DAVETx2 FBQ71DAVETx2
Indoor unit
Outdoor unit
Fan
unit
60
Indoor unit
Cooling capacity1,2
Rated (Min. - Max.)
Power consumption
COP
Colour
Indoor
Hermetically sealed scroll type
2.4
3.1
WALL MOUNTED TYPE
Power supply
Cooling capacity1,2
Rated (Min. - Max.)
Power consumption
Power supply
14 to 25
Ivory white
Note :
1
Rated cooling capacities are based on the following conditions: Indoor temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal).
2
Capacities are net, including a deduction for cooling for indoor fan motor heat.
3
Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions.
Model
Name
50
Model
Name
RZR140LVVM
1 Phase, 220–240 V, 50 Hz/
220–230 V, 60 Hz
1 Phase, 220–230 V, 60 Hz
Outdoor unit
Cooling capacity1,2
Rated (Min. - Max.)
Outdoor
unit
DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE
71
1.9
2.4
38 / 33
---------- 5
300X1,400X700
46
14 to 25
Ivory white
Hermetically sealed scroll type
2.9
1.8
3.7 (Charged for 30 m)
40 /36
2.4
2.9
50
49
45
1,170X900X320
99
101
-5 to 50
o/ 9.5
o/ 15.9
VP25 (I.D o/ 25XO.D o/ 32)
o/ 26.0 (Hole)
70 (Equivalent length 90 m)
30
Both liquid and gas piping
Note :
1
Rated cooling capacities are based on the following conditions: Suction temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal)
2
Capacities are net, including a deduction for cooling for indoor fan motor heat.
3
Initial setting is standard.
4
Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions.
5
Air filter is not standard accessory, but please mount it in the duct system of the suction side. Select its dust collection efficiency(gravity method) 50% or more.
26
Round flow type: List of optional parts required to achieve different flow patterns
SPECIFICATIONS
For each flow pattern – all round, 4-way, 3-way, 2-way, branch duct connection – the compatibility of each independently installed option
(shown in the column on the left) to accessory options (listed across the top of each table) is shown in the cells where the relevant row and column intersect.
A circle (o) indicates compatibility, and a cross (x) indicates incompatibility. Any options not shown below are not suitable for independent or accessory installation.
FLOOR STANDING TYPE
Indoor unit
Model
Name
Outdoor unit
Power supply
Outdoor
unit
60
71
FVQ50CVE
FVQ60CVE
Fan
Airflow rate
(H/M/L)
Cooling
Cooling
Night quiet mode
Dimensions (HXWXD)
Machine weight
Certified Operation range Cooling
Piping
Liquid (Flare)
connections
Gas (Flare)
Indoor unit
Drain
Outdoor unit
Max. interunit piping length
Max. installation level difference
Heat insulation
140
125
140
Optional accessory parts
Independently installable optional parts
1 Phase, 220–240 V, 50 Hz/220–230 V, 60 Hz
kW
W/W
5.0
(2.3-5,6)
1.27
3.94
6.0
(2.6-6.3)
1.84
3.26
7.1
(3.2-8.0)
2.58
2.75
18/16/14
635/565/494
43/41/38
1,850X600X270
39
3
m /min
cfm
dB(A)
mm
kg
Sound level3 Cooling (H/M/L)
Dimensions (HXWXD)
Machine weight
Certified Operation range Cooling
°CWB
Colour
Type
Compressor
Motor output
kW
Refrigerant charge
kg
(R-410A)
Sound level3
125
RZR50LVVM RZR60LVVM RZR71LVVM RZR100LVVM RZR125LVVM RZR140LVVM RZR125LVVM RZR140LVVM
kW
Cooling
100
FVQ71CVEB FVQ100CVEB FVQ125CVEB FVQ140CVEB FVQ60CVEx2 FVQ71CVEBx2
Outdoor unit
Cooling capacity1,2
Rated (Min. - Max.)
Power consumption
COP
Colour
Indoor
unit
All round flow 4-way flow
50
1.12
Hermetically sealed swing type
1.35
1.76
1.6
(Charged for 30 m)
48
44
595X845X300
43
dB(A)
dB(A)
mm
kg
°CDB
mm
mm
mm
mm
m
m
12.5
13.5
12.5
13.5
10.0
(5.7-14.0)
(6.2-15.4)
(5.7-14.0)
(6.2-15.4)
(5.0-11.2)
5.40
5.40
4.39
3.28
4.39
2.50
2.50
2.85
3.05
2.85
Fresh white
18/16/14
28/25/22
28/26/24
30/28/26
635/565/494
988/883/777
988/918/847 1,059/988/918
43/41/38
50/47/44
51/48/46
53/51/48
1,850X600X350
1,850X600X270
47
39
14 to 25
Ivory white
Hermetically sealed scroll type
3.1
2.03
2.4
3.1
2.4
2.7
(Charged for 30 m)
49
45
990X940X320
78
21 to 46
o/ 9.5
o/ 15.9
VP20 (I.D o/ 20XO.D o/ 26)
o/ 26.0 (Hole)
50 (Equivalent length 70)
30
Both liquid and gas piping
3.15
(Charged for 30 m)
50
45
46
1,170X900X320
97
Panel spacer1
o
Panel/grille related
Panel spacer1
Operation control related
Wireless remote controller
Auxillary function related
Fresh air intake kit (Chamber type)1,2
o
o
o
x
o
o
Fresh air intake kit (direct mount)
High-humidity operation kit
Filter related
Wireless
Fresh air intake kit Fresh air intake kit
remote controller (Chamber type)1,2
(direct mount)
High-efficiency filter2
Ultra-long-life filter2
o
o
o
o
o
o
o
o
o
x
x
x
o
o
o
o
o
High-humidity
operation kit
High-efficiency
filter2
Ultra-long-life
filter2
x
o
x
o
o
o
o
o
x
o
o
o
o
x
x
x
x
x
High-humidity
operation kit
High-efficiency
filter2
x
o
x
o
x
x
x
x
x
x
x
High-humidity
operation kit
High-efficiency
filter2
Ultra-long-life
filter2
x
x
x
x
x
x
o
o
o
3-way flow 2-way flow
Optional accessory parts
Independently installable optional parts
Panel spacer1
o3
Panel/grille related
Panel spacer1
Operation control related
Wireless remote controller
Auxillary function related
Fresh air intake kit (Chamber type)1,2
o3
o3
o3
x
o3
Fresh air intake kit (direct mount)
High-humidity operation kit
Filter related
Wireless
Fresh air intake kit Fresh air intake kit
remote controller (Chamber type)1,2
(direct mount)
Ultra-long-life filter2
o
o
o
o
o3
o
x
o3
o
x
x
o
o
o
Ultra-long-life
filter2
o3
o
o
o
x
46
97
Note :
1
Rated cooling capacities are based on the following conditions: Suction temp., 27°CDB, 19.0°CWB; outdoor temp. 35°CDB, 24°CWB. Equiv. refrigeration piping, 7.5 m (horizontal)
2
Capacities are net, including a deduction for cooling for indoor fan motor heat.
3
Anechoic chamber conversion value, measured according to JIS parameters and criteria. During operation these values are somewhat higher owing to ambient conditions.
Branch duct connection
Optional accessory parts
Independently installable optional parts
duct1
Branch
(Chamber type)
(Round duct type)
Panel spacer1
1-way branch / unit 3-way flow
2-way branch / unit 2-way flow
1-way branch / unit 2-way flow
Wireless
Fresh air intake kit Fresh air intake kit
remote controller (Chamber type)1,2
(direct mount)
o
x
x
o
o
o
o
o
o
o
o
o
4
4
4
1
In some cases, depending on how the unit is embedded in the ceiling, use of branch ducts and fresh air intake kits may not be possible. Before starting installation work make sure to check
whether or not joint installation is possible. In particular, ensure that the lower fixing position caused by the addition of panel spacers is acceptable.
2
Use a chamber connection kit if two different types of optional chamber are used together. In this case, the fresh air intake kit must be installed in the upper position.
3
It is not possible to use panel spacers in a 2-way flow installation.
4
It is not possible to install a branch duct on the same side to which a fresh air intake kit (direct mount) is installed.
Indoor unit
CEILING SUSPENDED TYPE
Name of option
Long-life filter
Fresh air intake kit
Drain pump kit
L-type piping kit (for upward direction)
Remote controller
OPTIONS
Indoor unit
CEILING MOUNTED CASSETTE TYPE
Name of option
Remark
Decoration panel
Sealing material of air discharge outlet
Panel spacer
Without the T-joint pipe and fan
Fresh air
Chamber
type
intake kit1
With the T-joint pipe, without fan
Direct installation type
Chamber connection kit2
Insulation kit for high humidity
(Colorimetric method 65%)
High-efficiency filter
(including chamber)
(Colorimetric method 90%)
Replacement
(Colorimetric method 65%)
high-efficiency filter
(Colorimetric method 90%)
Filter chamber
Replacement long-life filter
Ultra long-life filter
Replacement ultra long-life filter
Branch duct chamber
Wireless type
Cooling only
Remote controller
Wired type3
Navigation Remote Controller
Wired type3
Central remote controller4
Unified ON/OFF controller4
Schedule timer4
Touch Controller4
Adaptor for wiring5
Wiring adaptor for electrical appendices5
Installation box for adaptor PCB
Remote sensor (for indoor temperature)
Kit name
FCQ50KVEA FCQ60KVEA FCQ71KVEA FCQ100KVEA FCQ125KVEA FCQ140KVEA FCQ100KVLT FCQ125KAVLT FCQ140KAVLT
BYCP125K-W1
KDBH55K160F
KDBP55H160FA
KDDP55B160
KDDP55B160K
KDDP55X160
KKSJ55KA160
KDTP55K160
KDTP55K80
KAFP556B160
KAFP556B80
KAFP557B160
KAFP557B80
KAFP552B160
KAFP552B80
KAFP553B160
KAFP553B80
KDDFP55B160
KAFP551K160
KAFP55B160
KAFP55H160H
KDJP55B80
KDJP55B160
BRC7F633F
BRC1C61
BRC1E62
DCS302CA61
DCS301BA61
DST301BA61
DCS601C51
KRP1C63
KRP4AA53
KRP1H98
KRCS01-4B
Note: 1Refer to page 8 for the details.
2
Required for installing high-efficiency filter or ultra long-life filter.
3
Wiring for wired remote controller to be procured locally.
4
The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary.
5
Installation box for adaptor PCB (KRP1H98) is necessary.
27
Remark
Wireless type
Wired type1
Wired type1
FHQ71CAVEB
KAFP501A80
Cooling only
Navigation Remote Controller
Central remote controller2
Unified ON/OFF controller2
Schedule timer2
Touch Controller2
Adaptor for wiring
Wiring adaptor for electrical appendices3
Installation box for adaptor PCB
Remote sensor (for indoor temperature)
Electrical box with earth terminal (3 blocks)
Electrical box with earth terminal (2 blocks)
Kit name
FHQ100CAVEB
FHQ125CAVEB
KAFP501A160
KDDQ50A140
KDU50P140VE
KHFP5N160
BRC7GA56
BRC1C61
BRC1E62
DCS302CA61
DCS301BA61
DST301BA61
DCS601C51
KRP1BA54
KRP4AA52
KRP1D93A
KRCS01-4B
KJB311AA
KJB212AA
FHQ140CAVEB
Note: 1Wiring for wired remote controller to be procured locally.
2
The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary.
3
Installation box for adaptor PCB is necessary.
WALL MOUNTED TYPE
Name of option
Drain-up kit
Remote controller
Kit name
Remark
Wireless type
Wired type1
Wired type1
FAQ100CVEA
FAQ71CVEA
Cooling only
Navigation Remote Controller
Remote sensor (for Indoor temperature)
Central remote controller2
Unified ON/OFF controller2
Schedule timer2
Touch Controller2
Wiring adaptor for electrical appendices3
Installation box for adaptor PCB
Electrical box with earth terminal (3 blocks)
Electrical box with earth terminal (2 blocks)
Noise filter ( For electromagnetic interface use only)
K-KDU572EVE
BRC7EB519
BRC1C61
BRC1E62
KRCS01-4B
DCS302CA61
DCS301BA61
DST301BA61
DCS601C51
KRP4AA51
KRP4AA93
KJB311AA
KJB212AA
KEK26-1A
Note: 1Wiring for wired remote controller to be procured locally.
2
The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary.
3
Installation box for adaptor PCB (KRP4AA93) is necessary.
28
OPTIONS
DIMENSIONS
Indoor unit
(Unit: mm)
CEILING MOUNTED CASSETTE TYPE
DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE
[FCQ50-71]
[FCQ100-140]
16-M4 Hole
350
157
350
A
35 or less
(Note 4)
Connection position
of branch duct
(square-shaped type)
Connection position
of branch duct
(round shape type)
Connection position
of fresh air intake kit
(direct installation type)
157
350
67
95
29
157
350
2x100=200 80
25
160
80
C/L
213
C/L
160
80
130
256
167
93
Connection position
of branch duct
(square-shaped type)
20-M4
Prepared hole
124
27-M4 Prepared hole
5
2x100=200
25
213
60
105
2
280
330
55
42
150
35 or less
(Note 4)
Connection position
of branch duct
(round shape type)
157
840
81 2x100=200 85
64
124
50
[FCQ100-140]
160
124
109
95
80
55
3
95
110
124
16-M4 Prepared hole
55 Connection position
of branch duct
(square-shaped type)
1
167
[FCQ50-71]
Connection position
of branch duct
(square-shaped type)
20-M4
Prepared hole
[FCQ50-71]
4
B arrow view
90
183
ø10
(kn 0
ock
hole
)
Connection position
of branch duct
(round shape type)
Connection position
of fresh air intake kit
(direct installation type)
C arrow view
90
7
90
Hanging bolt
4-M8~M10
Connection position
of branch duct
(round shape type)
29
95
95
110
B arrow view
6
Connection position
of branch duct
(square-shaped type)
Drain Connection
Side
1500 or more
(required space) 160
From the floor side 2500 or more
For height installation
20 C/L
16-M4 Hole
157
350
Connection position
of branch duct
(square-shaped type)
A arrow view
840
340
80 2x100=200 80
124
Connection position
85 of branch duct
(round shape type)
2x100=200
160
C/L
93
160
124
157
350
950
C
81
160
67
8
[FCQ50-71]
55
Note 2
Piping Connection
Side
Connection position
85 of branch duct
(round shape type)
2x100=200
124
C/L
81
950
420
160
246
10
Note: 1If installing a high efficiency filter on the unit, an assembly chamber for either bottom or rear suction is required.
2
Wiring for wired remote controller to be procured locally.
3
The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary.
4
Mounting plate for adaptor PCB is necessary for each adaptor marked .
5
Up to 2 adaptors can be fixed for each mounting plate.
6
Only one mounting plate can be installed for each indoor unit.
9
860~910(Ceiling opening space) (Note 4)
710(Hanging bolt pitch)
420
780(Hanging bolt pitch)
Cooling only
300
or less
860~910(Ceiling opening space) (Note 4)
Wireless type
Wired type2
Navigation Remote Controller
Wired type2
Adaptor for wiring (interlock for fresh air intake fan)
Wiring adaptor for electrical appendices
Remote sensor
Mounting plate for adaptor PCB.4
Central remote controller3
Unified ON/OFF controller3
Schedule timer3
Touch Controller3
[FCQ50-140]
B
125
165
256
Air discharge adaptor
Remote controller
[FCQ50-140]
95
110
124
Filter chamber
Replacement long life filter
Replacement long life filter chamber kit
Service panel
FBQ125DAVET FBQ140DAVET
KAF372AA160
KAF373AA160
KDDF37AA160
KAF371AA160
KAF375AA160
KTB25KA160W
KTBJ25K160F
KTBJ25K160T
KDAJ25K140A
850
Adjustable(0~675)
65%
90%
High-efficiency filter1
Kit name
FBQ50DAVET FBQ60DAVET FBQ71DAVET FBQ100DAVET
KAF372AA80
KAF373AA80
KDDF37AA80
KAF371AA80
KAF375AA80
KTB25KA80W
KTBJ25K80F
KTBJ25K80T
KDAJ25K71A
BRC4C64
BRC1C61
BRC1E62
KRP1C64
KRP4AA51
KRCS01-4B
KRP4A96 5,6
DCS302CA61
DCS301BA61
DST301BA61
DCS601C51
175
Remark
50
40
Name of option
90
196
ø10
(kn 0
ock
hole
)
C arrow view
FLOOR STANDING TYPE
Outdoor unit
Name of option
Central drain plug
Wire fixture for preventing overturning
Fixture for preventing overturning
Demand adaptor
Refrigerant branch piping kit
RZR50LVVM
For twin multi
Name of option
Central drain plug
Fixture for preventing overturning
Demand adaptor
29
Base stationary type
Wire type
Kit name
RZR60LVVM RZR71LVVM RZR100LVVM RZR125LVVM RZR140LVVM
KKP014A4
KKPJ5G280
KKPJ5F180
------------------K-KYZP15C
KPT-60B160
---------KKTP5B112
KRP58M51
------------------KHRP58P216T
[FCQ100-140]
Required space
200mm or more
16-M4 Prepared hole
Hanging bolt
4-M8~M10
Connection position
of branch duct
(round shape type)
157
280
330
4
1
2
35 or less
(Note 4)
Connection position
of branch duct
(round shape type)
55
27-M4 Prepared hole
5
95
167
93
29
60
42
125
165
20 C/L
350
3
840
81 2x100=200 85
160
64
50
130
Connection position
of branch duct
(square-shaped type)
105
340
80 2x100=200 80
160
55
150
55
840
160
298
55
256
157
350
A
1500 or more 67
(required space) 160
From the floor side 2500 or more
For height installation
Note: 1Wiring for wired remote controller to be procured locally.
2
The indoor unit is equipped standardly with the interface adaptor for SkyAir series. An option is unnecessary.
3
Installation box for adaptor PCB (KRP4AA95) is necessary.
[FCQ100-140]
95
167
Wired
Wired type1
Kit name
FVQ71CVEB FVQ100CVEB FVQ125CVEB FVQ140CVEB
KAFJ95L160
BRC1C61
BRC1E62
DCS302CA61
DCS301BA61
DST301BA61
DCS601C51
KRP1BA57
KRP4AA52
KRP4AA95
850
Adjustable(0~675)
type1
FVQ60CVE
175
29
Replacement long-life filter
Remote controller
Navigation Remote Controller
Central remote controller2
Unified ON/OFF controller2
Schedule timer2
Touch Controller2
Adaptor for wiring3
Wiring adaptor for electrical appendices
Installation box for adaptor PCB
FVQ50CVE
160
288
10
Remark
50
40
Name of option
1500mm or more
1500mm
or more
1500mm
or more
200mm
or more
1500mm or more
The necessary space is 500mm or more when the
air-outlet is blocked with the accessory.
Moreover when the corner areas are blocked
(both right and left of the blocked air outlet),
the necessary space is 200mm or more.
35 or less
(Note 4)
Connection position
of branch duct
(square-shaped type)
Notes:
1
Sticking location for manufacture's label
manufacture's label for indoor unit:
Suction grille inner side's electric components box's lid surface
manufacture's label for decoration panel :
Decoration panel's corner decoration cover inner surface
2
In case of using wireless remote controller, this position will be a signal receiver. Refer to the drawing of wireless remote controller
in detail.
3
When the temperature and humidity in the ceiling exceed 30˚C and RH 80% or the fresh air is inducted into the ceiling or the unit
continues 24 hour operation, an additional insulation (thickness 10mm or more of glasswool or polyethylene form) is required.
4
Though the installation is acceptable up to maximum of 910mm square ceiling opening, keep the clearance of 35mm or less
between the indoor unit and the ceiling opening so that
the panel overlap allowance can be ensured.
5
Please do not place the thing been damp and troubled under an indoor unit.
When the case where humidity is 80% or more, and the drain outlet are choked up and the air filter are dirty, dew may fall.
1
2
3
4
5
6
7
8
9
Liquid piping connection
Gas piping connection
Drain piping connection
Transmission wiring connection
Remote controller wiring
connection
Air-outlet
Suction grille
Corner decoration cover
Drain hose (accessory)
Kit name
RZQ100KCTLT RZQ125KCTLT RZQ140KCTLT RZQ100LUYLT RZQ125LUYLT RZQ140LUYLT
KKPJ5F180
KPT-60B160
K-KYZP15C
KRP58M51
30
(Unit: mm)
WALL MOUNTED TYPE
CEILING SUSPENDED TYPE
157 63
115
1230
4
11
5
57
6
30 or more
(Service space)
30 or more
(Service space)
1270
Obstacle
Floor side
214
221
268
268
6
3
2
7
83
105
156
5
4
Notes:
1
Location of unit's Name Plate: Bottom of fan housing inside the suction grille.
2
In case of using wireless remote controller, this position will be a signal receiver.
Refer to the drawing of wireless remote controller in detail.
3
Please do not place the thing been damp and troubled under an indoor unit.
When the case where humidity is 80% or more, and the drain outlet are choked up and the air filter are dirty, dew may fall.
Piping direction
1
Name plate Note)2
Piping direction
1050
104
50 or more
(Requred space)
894
2500 or more
For installation
in high spaces
120 or less
52
φ80 hole
Piping and
Wiring intake
Outside line
φ80 hole
60
Mounting location
6
5
4
Approx.345
1
2
3
4
5
6
7
8
9
98
Approx.390
Approx.475
Notes:
1
Location of unit's of Name Plate:Right side surface of casing
2
In case of using wireless remote controller, this position will be a signal receiver. Refer to the drawing of wireless remote contorller in detail.
3
Please do not place the thing been damp and troubled under an indoor unit. when the case where humidity is 80% or more,
and the drain outlet are choked up and the air filter are dirty, dew may fall.
Front panel
Front grill
Air outlet
Gas piping
Liquid piping
Drain hose
Earth terminal
Right side piping connection hole
Left side piping connection hole
Connection position of fresh air intake kit
φ100(Knock out hole)
120
90
12
10
157 63
115
90
175
92
51 60
50 or more
(Required space)
116
Piping direction
9
40
260
[FAQ100CVEA]
Approx.440
63
134 59
242
240
Position slit hole for taking out in piping back
(View from the front)
7
30 or more
(Service space)
1590
Obstacle
Floor side
30 or more
(Service space)
The Front
Brand name plate
(Note.2)
Drain piping connection VP20
(For left piping)
214
221
268
268
6
76
3
2
7
5
83
105
156
4
Notes:
1
Location of unit's Name Plate: Bottom of fan housing inside the suction grille.
2
In case of using wireless remote controller, this position will be a signal receiver.
Refer to the drawing of wireless remote controller in detail.
3
Please do not place the thing been damp and troubled under an indoor unit.
When the case where humidity is 80% or more, and the drain outlet are choked up and the air filter are dirty, dew may fall.
6
o/ 45
14
Position : Hole of wall for taking out in piping back
(View from the front)
1 Air discharge grille
2 Air suction grille
3 Air filter
4 Gas piping connection
5 Liquid piping connection
6 Drain piping connection
7 Earth terminal (inside the control box) (M4)
8 Hanger
9 Rear piping penetration cover
10 Top panel penetration cover
11 Right side piping connection
12 Left back drain piping connection
13 Left side drain piping connection
14 Right side drain piping connection
15 Hole of wall for taking out in piping back
16 Upward drain piping connection
17 Upward gas piping connection
18 Upward liquid piping connection
19 Power supply wiring and a unit wiring back connection
20 Power supply wiring and a unit wiring upper connection
9
2
1
30 or more
(Required space)
50 or more
(Requred space)
Piping direction
1200
79.5
3
Name plate Note)2
Piping direction
1085
2500 or more
For installation
in high spaces
50 or more
(Requred space)
8
120 or less
35.5
φ80 hole
Outside line
Piping and
Wiring intake
φ80 hole
6
65
5
Mounting location
4
Approx.400
89
Approx.460
Approx.465
Notes:
1
Location of unit's of Name Plate:Right side surface of casing
2
In case of using wireless remote controller, this position will be a signal receiver. Refer to the drawing of wireless remote contorller in detail.
3
Please do not place the thing been damp and troubled under an indoor unit. when the case where humidity is 80% or more,
and the drain outlet are choked up and the air filter are dirty, dew may fall.
114
235
300 or more
(Required space)
57 13
57
Dimensions for
full open
front panel
45
11
91
131
197
5
220
103
14.5
4
1
19 15
45
Hanging bolt
4-M8~M10
175
690
340
1550
(Hanging bolt pitch)
5
(Required space)
8
5
(Required space)
For height installation
(Hanging
bolt pitch)
210
18 17 20 16
210
156
105
102
131 57
30
87
100
163
189
195 35
[FHQ100-140CAVEB]
From the floor side 2500 or more 197
2
WALL MOUNTED TYPE
CEILING SUSPENDED TYPE
31
8
3
9
50 or more
(Requred space)
1 Air discharge grille
2 Air suction grille
3 Air filter
4 Gas piping connection
5 Liquid piping connection
6 Drain piping connection
7 Earth terminal (inside the control box) (M4)
8 Hanger
9 Rear piping penetration cover
10 Top panel penetration cover
11 Right side piping connection
12 Left back drain piping connection
13 Left side drain piping connection
14 Right side drain piping connection
15 Hole of wall for taking out in piping back
16 Upward drain piping connection
17 Upward gas piping connection
18 Upward liquid piping connection
19 Power supply wiring and a unit wiring back connection
20 Power supply wiring and a unit wiring upper connection
Brand name plate
(Note.2)
76
Position : Hole of wall for taking out in piping back
(View from the front)
14
o/ 45
The Front
Drain piping connection VP20
(For left piping)
Dimensions
for full open
front panel
105
13
57
300 or more
(Required space)
235
91
131
197
1
220
103
44
Hanging bolt
4-M8~M10
19 15
7
14.5
690
240
238
Position slit hole for taking out in piping back
(View from the front)
(Hanging bolt pitch)
50 or more
(Required space)
10
Approx.400
63
134 59
12
30 or more
(Required space)
60
5
175 (Required space)
5
(Required space)
For height installation
90
92
51
Piping direction
290
116
9
90
8
From the floor side 2500 or more 197
Connection position of fresh air intake kit
φ100(Knock out hole)
120
40
260
(Hanging
bolt pitch)
210
18 17 20 16
[FAQ71CVEA]
175
210
156
105
102
131 57
30
87
100
163
189
195
35
[FHQ71CAVEB]
44
DIMENSIONS
1
2
3
4
5
6
7
8
9
Front panel
Front grill
Air outlet
Gas piping
Liquid piping
Drain hose
Earth terminal
Right side piping connection hole
Left side piping connection hole
32
DIMENSIONS
(Unit: mm)
DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE
Suction grille
stopper
P
150
B
Ceiling
Inspection hatch
700
Inspection hatch 2 or more
(same as the indoor
View B-1
unit size or more)
(From the Air outlet)
18-8X12 oblong hole
(All around)
513
541
616
80
According to any one of below 1) ~3), secure a space for service works, such as, checking and maintenance of control box, etc.
1) One inspection hatch (450X450) on the control box side and a space of 300mm or more under the unit. (Fig.A)
2) One inspection hatch (450X450) on the control box side and 2 (two) inspection hatches under the unit. (Arrow View B-1)
3) 3 (three) inspection hatches under the unit and the control box. (Arrow View B-2)
95
A
B
200
223
253
34
(From the Air inlet)
Floor surface
Notes)
Location of MANUFACTURE'S LABEL: Control box surface
2
Mount the air filter at the suction side. (Select its colorimethod (gravity method) 50% or more.)
3
Do not locate things should not be wet under the indoor unit. Dews may drop when humidity reaches over 80%, or a drain gets stuck, or air filters are not clean.
4
Space for Service Works
1
50
Liquid pipe connection
Gas pipe connection
Drain pipe connection
Ground terminal (Terminal in Control box)
Control box (Inside)
Remote control wiring connection
Power-source wiring
and a unit wiring connection
8 Air discharge flange
9 Air suction flange
10 Hook
950
100
1
2
3
4
5
6
7
925
C
[FBQ100/125/140DAVET]
326
300
20
342
7
Air inlet
200
or less
300
or more
131
Control box
5
4
30
6
6
6
H
J
K
L
184
184
A
B
C
D
FVQ50/60CVE, 71CVEB 50 110 186 270
FVQ100/125/140CVEB
130 190 266 350
mo
Required space
E
45
44
F
50
49
G
H
J
K
L
50 110 180 186 242
130 190 260 266 322
M
57
79
N
P
144 149
202 229
78
573.5
80
8X150=1200
1325
1350
(From the Air inlet)
Floor surface
Notes:
1
Location of MANUFACTURE'S LABEL: Control box surface
2
Mount the air filter at the suction side.(Select its colorimethod (gravity method) 50% or more.
3
Do not locate things should not be wet under the indoor unit.Dews may drop when humidity reaches over 80%,or a drain gets stuck,or air filters are not clean.
4
Space for Service Works
According to any one of below 1)~3),secure a space for service works,such as,checking and maintenance of control box,etc.
1)One inspection hatch (450X450) on the control box side and a space of 300mm or more under the unit.(Fig.A)
2)One inspection hatch (450X450) on the control box side and 2 (two) inspection hatches under the unit.(Arrow View B-1)
3)3 (three) inspection hatches under the unit and the control box.(Arrow View B-2)
Earth terminal
in switch box
595
200
or less
Wiring inlet
60
105
20-8X12 oblong hole
(All around)
Name plate
Service port
1
2
3
4
5
6
7
8
9
10
11
12
Liquid piping connection
Gas piping connection
Drain piping connection
Earth terminal
(Terminal in Control box)
Control box(Inside)
Remote control wiring
connection
Power supply wiring and a
transmission wiring
Air discharge flange
Air suction flange
Hanger
Socket (for maintenance)
Drain hose(Accessory)
272
713
or less
Hole for anchor bolts
(M8 or M10)
112
View
(From the Air outlet)
B
Inspection
Ceiling
hatch
700
700
Inspection hatch 2
or more
or more
(SAME AS THE
View B-1 View B-2
INDOOR UNIT
SIZE OR MORE)
163
300 12
Inspection hatch 1
(450mmX450mm)
Control box
Inspection hatch 3
(SAME AS THE
INDOOR UNIT
SIZE +300 OR
MORE)
Control box
269
49
150
277
247
150
300
3X65=195
700
300 or more
(Note.4)
2500 or more
(A case without
the ceiling)
(467 or less)
212
144
40
2X65=130
700 or less
232 Adjustable
Air inlet
(Note.2)
CASE 2),3)
20
or more
165
7X150=1050
700 or more
(Service space)
Ceiling
33
Unit base
1400
or more
635
245
215
150
200
or less
65
450 or more
(Service space)
(SAME AS THE INDOOR
UNIT SIZE OR MORE)
20-8X12 oblong hole
(All around)
1185
28 7 4
1
or
Fig.A
1160
5
Control box
Air outlet
1400
Inspection hatch
Ceiling
9
169
11
290
re
0
50
300
1700
or more
19X65=1235
Control box
Air inlet
2 6
845
Inspection hatch 1
(450mmX450mm)
48- 4.7 Hole
(All around)
1205
16X65=1040
1438(Hanging bolt pitch)
CASE 1)
10
8
Air outlet
mo
Drain outlet
I.D. 18 hose for connection
631
(Hanging bolt pitch)
167 3 1
3
F
598
Notes:
1
Sticking location for manufacturer’s label: on the surface of
cover of switch box inside the suction grille.
or
OUTDOOR UNIT // RZR50/60/71LVVM
DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE
Inspection hatch 450 or more
G
E
6X150=900
Ceilling
Full open
position of
suction grille
825
150
247
277
(Note.4)
2500 or more
(A case without
the ceiling)
700
150
300
28
4
3X65=195
290
7
300 or more
26
2X65=130
212
144
3
130
Approx.46
10
50
1 Suction grille
2 Air filter
3 Through hole for side piping
(70x90 oblong slit hole)
4 Through hole for side piping
( 80 slit hole)
5 Through hole for side piping
( 27 slit hole)
6 Through hole for rear
piping/wiring
(80x130 oblong slit hole)
7 Through hole for bottom
piping/wiring
(126x130 square hole)
8 Liquid pipe connection
9 Gas pipe connection
10 Drain pipe connection
1
9
Air outlet
169
2-7X15
oblong hole
(For wood screw)
95
Air inlet
(Note.2)
5
mo
2
50
6
8
700
or more
View B-2
or
re
Fixture
(Accessory)
75
2
1000
200
or more or less
20
or more
150
785
50
re
100
215
245
200
or less
65
450 or more
(Service space)
760
1
Inspection hatch 1
(450mmX450mm)
Control box
Inspection hatch 3
(Same as the indoor
unit size + 300 or more)
Control box
Control box
43
Air inlet
Fig.A
330
740 or more
(Pull out dimension of air-filter)
Air
outlet
D
Pull out
direction
of air-filter
314
Ceiling
CASE2), 3)
5X150=750
N
Unit base
9
Inspection hatch 450 or more
Air outlet
In case of fixing it at the bottom
In case vibration resistance is
required, fix it at both the bottom
and the rear.
View
68
600
677
Inspection
hatch
Detail
(Two both sides)
1850
16-8X12 oblong hole
(All around)
435
700 or more
(Service space)
27
This model to be fixed with fixture
as shown below.
126
0.7
1300
or more
Air inlet
Inspection hatch 1
(450mmX450mm)
Control box
200
or less
300
or more
1000
13X65=845
805
CASE 1)
Control box
View
40- 4.7 Hole
(All around)
130 215
7
11X65=715
1038 (Suspention bolt position)
4- 14 Hole
(For bolt)
18
36-φ4.7 hole
(All around)
8
Air outlet
260
10
631
(Suspention bolt position)
30-φ4.7 hole (All around)
M
[FBQ50/60/71DAVET]
FLOOR STANDING TYPE
144
20
Liquid stop valve
( 9.5CuT)
Service port
Gas stop valve
( 15.9CuT)
Drain outlet
21
94
Drain outlet
200
299
419
449
479
509
559
34
DIMENSIONS
(Unit: mm)
OUTDOOR UNIT // RZR100LVVM
REMOTE CONTROLLER
350
(345~355)
30
Hole for anchor bolt 4-M12
Wireless type
37
55
320
•
Remote controller dimensions
CEILING SUSPENDED TYPE
• Receiver installation procedure
CEILING MOUNTED CASSETTE TYPE <Round Flow>
• Receiver installation procedure
Transmitting part
The Front
30
Refrigerant
piping side
620
157
91
160
Receiver
Receiver
38
160
940
30
3
62
4
7
2
7
6
6
5
5
7
•
55
Remote controller
holder
223
53
53
84
95
19
142
Decoration panel
• Receiver detail
Liquid crystal
remote controller
(wireless)
55
340
95
19
89
6
53
89
339
60
5
Remote controller holder
installation procedure
<installation to wall surface>
• Receiver detail
95
990
1
Drain piping
side
17.5
80
52
WALL MOUNTED TYPE
• Receiver installation procedure
DUCT CONNECTION MIDDLE and HIGH STATIC PRESSURE TYPE
13
145
•
67
Receiver detail
2-5x9 Slot
90
Receiver
16
(Ceiling opening)
3 Service port
4 Earth terminal
5
72
83.5
106
68
120
1 Gas piping connection
2 Liquid piping connection
161
260
279
285
16
8
• Receiver
detail
5 Refrigerant piping intake
6 Power supply wiring intake
36
61
7 Transmission wiring intake
8 Drain piping connection
262
416
595
70
0.5
35
18
49
(Ceiling opening)
Switch box
(field Supplied parts)
Service space for ceiling installation
Wired type
• Remote controller dimensions
BRC1C61
320
61
43
• Installation method
A Exposed body, exposed cord
B Exposed body, embedded cord
17
Staple
620
42
140
117
0~5
900
30
84
38
94
140
120
4
17
18
Cord
outlet
hole
23 28
3
(Between remote
controller and
control box)
17
Size
0.75~1.25 mm
Total length
500 m
6
6
5
BRC1E62
Upper case
A Exposed cord
42
40
5X7 oblong hole
80
52
145
13
28
23
46
5X15 oblong hole
48.5
48.5
Left outlet
19
Lower case portion
Note)2
28
Through hole
Switch box for one switch
( 8- 10)
ex.) KJB111A
(optional accessory)
Lower case
67
Note)
1. Remote controller cord and staple are not attached. They are field
supplied parts.
16
16
58
70 102 117
35
376
191
19
Code outlet hole
19
Specifications of cord
45
Condit
C Embedded cord
(use switch box)
19
84
95
223
B Embedded cord
Staple
Top center
outlet
40
120
55
Operation
lamp
(Green)
120
53
19
5
Note)
1. Remote controller cord and staple are not
attached.
They are field supplied parts.
• Installation method
Lower case
Top left
outlet
55
54
54
89
60
84
95
95
422
423
5
71
2
84
1170
7
5
8
Shield wire (insulated thickness: 1 mm or more)
7
6
142
Control box
Type
7
Through hole
( 12- 16)
Specifications of cord
1
19
17
46
2
89
Remote
controller
Remote
controller
120
30
41
C Exposed body, embedded code
Conduit
Remote
controller
84
350
(345~355)
30
Hole for anchor
bolt 4-M12
Note :
Do not install more than 3 receivers in
the vicinity of one another.
With 4 or more units, there is always
the possibility of malfunction
More than 90
(Srevice space)
OUTDOOR UNIT // RZR125/140LVVM, RZQ100/125/140KCTLT, RZQ100/125/140LUYLT
1 Gas piping connection
2 Liquid piping connection
3 Service port
4 Earth terminal
Type
Vinyl cord with sheath or cable (insulated thickness: 1mm or more)
Size
0.75~1.25 mm2
Total length
500 m
46
0~5
Switch box for two switch (Between remote
ex.) KJB211A
controller and
(optional accessory)
control box)
Switch box
portion
[field supplied part]
2.If the hole size is too large or the location
is not proper, the hole may come out from
the remote controller.
5 Refrigerant piping intake
6 Power supply wiring intake
7 Transmission wiring intake
8 Drain outlet
36
Installation service space for outdoor unit
For RZR50-140LVVM
For RZQ100-140KCTLT, 100-140LUYLT
2.RZR100-140LVVM
1 When there is an obstruction on the inlet side
2 When there is an obstruction on the outlet side
1) When the overhead space is open
1) When the overhead space is open
1
1. For single
unit installation
2
re
or
mo
0
10 ore
m
or
1
10
25
0o
rm
ore
0o
25
0o
rm
0
10
ore
mo
or
rm
ore
re
10
0
1
or
0
10 ore
m
or
mo
re
0
00
or
mo
re
1
0
00
or
mo
2. For multiple units installation
(more than two units)
10
0
mo or
re 10
0
mo or
re
re
100
or m
ore
re
100
or m
ore
2) When there is an obstruction in the overhead space
When there are obstructions on both sides
50
2
0o
r le
An obstruction
in the overhead
space
ss
1
50
0o
r le
ss
2
r
0o
10
10
00
or
ss
r le
0o
1. For single unit installation
An obstruction
in the overhead space
mo
re
00
o
rm
0o
ore
mo
re
0
50
50
1
0o
r le
1. For single unit installation
2
50
0o
r
An obstruction
in the overhead
space
2
25
0o
rm
ore
0
10
0o
o
rm
An obstruction
in the overhead
space
re
0
10
0
0o
m
or
mo
0
10 ore
m
or
When there are obstructions on the inlet side and
both lateral sides
An obstruction
in the overhead
space
15
0o
r le
ss
2
o
rm
re
or 150
mo
re
or 150
mo
re
1. For single unit
installation
1
1
or 000
mo
re
or 250
mo
re
(There is no limit to the height of the obstruction on the
outlet side.)
or m
150
e
or
rm
o
50
or m
ore
1
1. For single unit installation
50 ore
m
or
L
H
0
50 ore
m
or
0
10 ore
m
or
les
s
1
or 200
mo
re
10
0
mo or
re
An obstruction
in the overhead
space
10
or
mo
rm
ore
ore
00
10 ore
m
or
0
10 ore
m
or
10
0
mo or
re 10
0
mo or
re
0
30 ore
m
or
L
H
00
10 ore
m
or
0
30 ore
m
or
H
0
20 ore
m
or
37 Note : As for other patterns of installation, please refer to Installation manual or Engineering Data Book.
0
50 ore
m
or
re
2
rm
H
2. For multiple units installation
(more than two units)
10
0o
rm
ore
0o
0o
ss
r le
0o
50
20
25
0
30 ore
m
or
When there are obstructions
on the inlet side and
both sides
00
L
50
0
20 ore
m
or
L
L
2. For series installation (more than two units)
r
0o
1
or 000
mo
re
or 250
mo
re
1) When the overhead space is open
2
0
50 ore
m
or
1000 or more
5
1000 or more
00
(When the obstruction on the outlet side is higher than the
unit itself)
2. For multiple units installation (more than two units)
0
15 ore
m
or
An obstruction
in the overhead
space
2
ss
150
3 When there are obstructions on both
the inlet and outlet sides
(There is no limit to the height of the obstruction on the
outlet side.)
When there are obstructions on the inlet side and
both lateral sides
le
or
ss
r le
0o
50
ore
1) When the overhead space is open
2. For series installation (more than two units)
1
An obstruction
in the overhead
space
re
mo
e
or
When there are obstructions
on the inlet side and
both sides
(When the obstruction on the outlet side is higher than the
unit itself)
or
H
or 250
mo
re
5
o
00
An obstruction
in the overhead
space
rm
3 When there are obstructions on both
the inlet and outlet sides
10
0o
rm
ore
00
10
0o
H
s
r
0o
50
10
L
or 150
mo
re
50
les
1000 or more
1
r
0o
1000 or more
or
An obstruction
in the overhead space
s
les
ore
re
0
10
ss
r le
0o
50
10
0
mo or
re
1. For single unit installation
When there is an
obstruction on the
inlet side
mo
L
ss
r le
50
2. For multiple units installation
(more than two units)
2) When there is an obstruction
in the overhead space
ss
ss
mo
1000 or more
r le
1000
or more
0o
s
les
1000 or more
When there is an obstruction on the inlet side
50
ore
ore
2. For series installation (more than two units)
2) When there is an obstruction in the overhead space
1
m
or
or
or
H
rm
50
r
0o
0
30
1000 or more
0o
0
20 ore
m
or
or 250
mo
re
0
30 ore
m
or
rm
1000 or more
20
1000 or more
or 250
mo
re
0
50
re
20
ore
1000 or more
1
or 000
mo
re
mo
50
re
10
or
10
2) When there is an obstruction
in the overhead space
10
0
mo or
re 10
0
mo or
re
When there are
obstructions on
both sides
00
re
mo
2. For multiple units installation
(more than two units)
1. For single unit installation
2. For series installation (more than two units)
1
ore
rm
0o
10
1000 or more
ore
re
mo
or
0
50
2
2
rm
0o
When there is an
obstruction only
on the inlet side
re
When there are obstructions
on both sides
1
0o
50
o
rm
2. For series installation (more than two units)
When there are obstructions on
both sides
10
1. For single unit installation
1. For single unit installation
0
50 ore
m
or
50
1) When the overhead space is open
1) When the overhead space is open
2
1000 or more
When there is an
obstruction only
on the inlet side
2 When there is an obstruction on the outlet side
1000 or more
1. For single unit installation
1
1 When there is an obstruction on the inlet side
1000 or more
1.RZR50/60/71LVVM
L
H
00
10 ore
m
or
0
30 ore
m
or
Note : As for other patterns of installation, please refer to Installation manual or Engineering Data Book.
38