Transcript
User Manual 2901 Bluetooth Headset Contents Safety Approvals and Certification..............................................................………….3 FCC Notices FCC RF Exposure requirements CE Statement Introduction....................................................................................................………..4 Operation instructions Introduction Power on Power off Pairing Power-saving mode.......................................................................................………..5 Receiving an incoming call Voice dialing Power-saving mode Receiving an incoming call Voice dialing Rejecting an incoming call Last number redialing Volume adjustment Low-batter warning Redial automatically Charging End speaking Low-batter warning....................................................................................……..…….6 Redial automatically Charging End speaking Performance parameter Important information.....................................................................................………..7 Trouble clearing Storage environment..................................................................................…………..8 GFM Guarantee ......................................................................................…...…….…9 2 Safety Approvals and Certification Users are advised not to make changes or modify the device in any way. Changes or modifications not expressly approved by GFM will void the warranty. FCC Notices This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. FCC RF Exposure requirements: This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCECAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONSCOULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. User’s authority to operate the equipment Note: this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful inter ference in a residential installation. this equipment generates, used in accordance with the instructions, may cause harmful interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : - Reorient or relocate te receiving antenna - Increase the separation between the equipment and receiver - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio TV technician for help. CE Statement Important Notice: This device is a 2.4GHz FHSS Bluetooth headset, intended for office and home uses in all EU and EFTA member states. The Bluetooth trademarks are owned by Bluetooth SIG, Inc., U.S.A. and licensed to OMIZ. 3 Introduction 1.1 Bluetooth technology Bluetooth is a standard of wireless communication. Bluetooth technology is a kind of short distance wireless communication technology and an open global criterion. The Bluetooth products work on universal industry, science, medical (ISM) frequency. In order to avoid interference, adopt jumping frequency technique, divide 2.4GHz ~ 2.4835GHz into 79 channels, transmit data at 1600 time/sec. The transmission distance is about 10m (Class Ⅱ). ISM frequency of 2.4GHz is free open frequency, no need to apply for license. Operation instructions Introduction BT-020C Bluetooth headset key-press and key-press function explanation MF B Ca sing V o L+ In dica to r Vo L- M IC Ch arging to uch spot A. MFB key-press: realize power on, power off, receiving, voice dialing, hang-up, pairing etc. B. Volume +: realize increasing volume, mute, rejecting incoming call, redialing etc C. Volume -: realize decreasing volume etc. Power on In the state of power off, long press MFB, speaker will give off short BEEP sound. Blue light fleshes. Then BT-020C will power on. Power off In the standby state, long press MFB, speaker will give off long BEEP sound. Blue light closes. Then BT-020C will power off. Pairing Firstly, confirm BT-020C Bluetooth headset is in the state of power off and is in the effective distance with other Bluetooth devices. 4 will flash alternately. Then BT-020C will in pairing state. b. Open Bluetooth function of mobile phone, choose Bluetooth device on mobile phone to search function, and proceed to search for BT-020 Bluetooth headset until BT-020C shows on mobile phone. c. Select Bluetooth device d. Input ID code 0000, and confirm, then mobile phone pairing with BT-020C Bluetooth headset. e. After successful pairing, Blue and red indicator flash alternately changes to blue light flashes. Then the whole pairing process is over automatically. Power-saving mode a. When BT-020C Bluetooth headset fail in the process of pairing, after about 60sec, enter the standby state automatically, after more 10 sec, BT-020C will power off automatically. b. When BT-020C Bluetooth headset disconnect with any Bluetooth device in the state of power on, it will close automatically after 5 minute. Receiving an incoming call When BT-020C Bluetooth headset is power on and connects with mobile phone, telephone in. a. Short press MFB. b. Then blue indicator changes from slow flash to quick flash. c. If BT-020C Bluetooth headset has no power on, please open it firstly. After redialing mobile phone automatically (press one time to connect with mobile phone), press MFB again, then you can receive the incoming call. Voice dialing When BT-020C Bluetooth headset is power on and connects with mobile phone, you want to voice dialing. The function demands Bluetooth mobile phone to have voice recognition function. a. Short press MFB, you can hear short BEEP sound, then enter voice dialing. b. Speak the person's name saved in telephone book of mobile phone. c. Mobile phone will dial according to the number in telephone book of mobile phone. Rejecting an incoming call When BT-020C Bluetooth headset is power on and connects with mobile phone, telephone in but not to receive, long press VOL+, then the incoming call is rejected. Last number redialing In the standby state, long press volume +. Volume adjustment 5 In the state of standby, speaking and calling etc, short pressing volume + or volume -, you can adjust volume. Short press volume + one time, the volume adds one step; Short press volume -, the volume decreases one step. When volume is adjusted to maximum or minimum, it will sound a warning. Low battery warning When the battery of BT-020C Bluetooth headset is not enough, blue light closes, red light flashes, and speaker send short BEEP sound. Then you should charge BT-020C Bluetooth headset. Rebind automatically When BT-020C Bluetooth headset is power on and disconnects with devices, also in effective distance with mobile phone, if mobile phone connects and pairs with BT-020C, it will rebuild connection with mobile phone automatically. Charging Plug DC head of power adapter into charging interface of charging socket, then place BT-020C Bluetooth headset into charging socket, close the upper cover of charging socket, and then plug in power supply of power adapter, red light turns on, which means charging begin; red light goes out, which means charging end. End speaking In the process of speaking, short press MFB, it can end speaking. Performance parameter Item Parameter Standard Effective range Audio frequency Frequency Connection Speaking time Standby time after pairing Standby time while power on and non-pairing RF Power Power consumption of power supply Battery capacity Battery70mAh 6 Bluetooth V2.0 10m without obstacle 15bits S/N 70db 2.4GHZ-2.4835GHZ ISM Band Point-to-Point 4-5hrs About 70hrs Close automatically after 5 minute 0dBm (class Ⅱ) 18~25mA when speaking Rechargeable Lithium Polymer Storage temperature Pairing code 0000 Pairing evice but need to connect by turns Operation voltage Receiving sensitivity Standard allocation charging socket, charger(5V+0.2), s -20℃ to +85℃ One-to-one, allow many primary 3.0~4.2V -70dBm Headset main body, headset, c d Storage environment a. Working temperature environment: 0℃ to 60℃without loss of function b. Storage temperature require: -20℃ to 60℃without any damage to the Kit’s contents c. Humidity range: 30﹪-90﹪humidity @ 60℃ without loss of function h p Important information Product maintenance a. Keep the product dry at all times. Only use a clean soft cloth to clean Bluetooth headset surface. b. Store headset away from areas containing high dust levels, and away from extremely high or low temperatures. c. Do not attempted to disassemble or repair the headset by yourself as this will cause damage to the product. d. Product should be disposed of properly. e. Dropping, throwing or any other forms of abuse to the headset will cause damage. GFM Guarantee: If you are not totally satisfied with this GFM product, you may return it to any Meijer store for a full refund within 6 months (180 days) of purchase when accompanied by a receipt. WHAT IS COVERED: Meijer will pay the cost of labor and repair or replacement parts in the event Your Covered Product fails to operate as a result of a mechanical or electrical failure caused by defects in workmanship and/or materials. A mechanical or electrical failure caused by a direct result of a power surge is also covered. Parts will be replaced with those of like kind and quality, and may be new or remanufactured. If the Covered Product Dist. by Wholesale Merchandisers, Inc., 2929 Walker, NW, Grand Rapids, MI 49544 Made in China Trouble Shooting Phenomenon Reason Solving method Can not power on Low battery Charging up headset 2 -3 hrs No voice after pairing Incorrective pairing Pairing again Can speak but red light Low battery, red light flashes Charging flashes Charging without indication up headset immediately AC adapter without voltage Check AC adapter if plug or output the switch of power supply is open. Headset shuts down Low battery Charging up headset 2 -3 hrs Headset has echo. Volume is too loud or the environment is too noisy Change your setting or adjust Hearing noise from headset There is environmental interference or the headset is too far from the source device Change your setting or pull The headset is producing only low volume from the other end The pairing of headset is not Adjust the position of headset automatically B volume headset and device closer. correct. 7 8 9
