Download LS Drive Series iG5A Catalog

www.lsis.com
Compact & Powerful Drive
iG5A
0.4~1.5kW (0.5~2HP) 1phase 200~230Volts
0.4~22kW (0.5~30HP) 3Phase 200~230Volts
0.4~22kW (0.5~30HP) 3Phase 380~480Volts
Drive
Starvert iG5A
LS Starvert iG5A is very competitive in its price and shows an upgraded functional strength.
User-friendly interface, extended drive ranges up to 22kW,
superb torque competence and small size of iG5A provides an optimum use environment.
Standard
compliance
Compactness
iG5A
High
performance
Userfriendliness
& Easy
maintenance
2
Compact & Powerful Drive iG5A
Contents
4
8
9
11
13
15
16
18
20
23
25
42
43
Overview
Model & Type
Standard Specifications
Wiring
Terminal Configurations
Keypad Features
Parameter Setting
Trial Run
Dimensions
Braking Resistors and Peripheral Devices
Function List
Protective Functions
Fault Remedy
Drive Starvert iG5A Series
3
iG5A
Powerful & Upgraded Performance
iG5A provides sensorless vector control, PID control,
and ground-fault protection through powerful built-in functions.
Sensorless vector control
Ground-fault protection
during running
The ground-fault protection of output terminal
is possible during running.
Vector Control Mode: Auto tuning Measure maximum
Condition: Sensorless
torque (%) at each speed (1/5/10/20/30/40/50/60Hz)
Speed (Hz)
Torque (%)
The built-in sensorless vector control provides
the superb speed control and powerful high
torque.
Speed vs Torque Characteristics
Analog control from -10V to 10V
Inputting analog signals from -10V to 10V
provides user-friendly operation.
+10
Forward
Reverse
-10
Built-in PID control
The built-in PID function enables to control
flow-rate, oil-pressure, temperature, etc
without any extra controller.
PID control
Pl control
PI
Built-in dynamic braking circuit
The built-in dynamic braking circuit minimizes
deceleration time via braking resistors.
Speed
Built-in 485 communication
The built-in RS-485 communication supports
remote control and monitoring between iG5A
and other equipment.
Wide product range
iG5A consists of the product range from 0.4 to 22KW.
4
With braking resistor
Normal state
Reducing
deceleration time
Time
Compact & Powerful Drive iG5A
RS-485 communication
Connected to PC
RS-485 - 232C converter
Monitoring
Checking operation status
(Voltage, Current, Frequency, etc)
Checking modified parameters
Windows support
Remote Control
Convenient remote control to modify operation status
(Forward/Reverse operation, Frequency, etc)
Easy parameter setting
Available to control up to 31 Drives
RS-485, Modbus communication
Connected to XGT panel
Monitoring
Checking operation time
Automatic list-up of trip record
Language support (Korean, English, Chinese)
Remote Control
Convenient remote control to modify operation status
(Forward/Reverse operation, Frequency, etc)
Easy parameter setting
Available to control up to 31 Drives
RS-485, Modbus communication
Drive Starvert iG5A Series
5
iG5A
User-friendly Interface & Easy Maintenance
The parameter setting becomes easier by adopting the 4 directions key. And iG5A supports
easy maintenance via diagnosis and fan changeable structure.
Diagnosis of output module
Through easy parameter setting, iG5A can diagnose the
status of output module.
Easy change of fan
iG5A is designed to be the fan changeable structure in
preparation for a fan breakdown.
Cooling fan control
By controlling the cooling fan, iG5A provides a virtually
quiet environment according to the status of operation.
User-friendly interface
The 4 directions key provides easy handling and
monitoring.
External loader (Optional)
The external loader away from a panel enables to control
and monitor conveniently. And the parameters made by
external loader can be copied and applicable to other
Drives.
Loader type + External type (Optional)
Model name
INV, REMOTE KPD 2M (SV-iG5A)
INV, REMOTE KPD 3M (SV-iG5A)
INV, REMOTE KPD 5M (SV-iG5A)
6
Remarks
2m
3m
5m
Compact & Powerful Drive iG5A
Compact Size
The compact size achieves cost-efficiency and various applications.
Same height from 0.4 to 4.0kW (128mm)
Global standard compliance
CE UL
Global standard
iG5A series complies with CE and UL standards.
PNP/NPN input
Both PNP and NPN inputs become possible and these enable to
use the outer power.
To do so, users will be given wider choices of selecting the
controller.
Drive Starvert iG5A Series
7
iG5A
Model & Type
Applicable motor ranges
1 Phase 200V
3 Phase 200V
3 Phase 400V
0.4kW (0.5HP)
SV004iG5A-1
SV004iG5A-2
SV004iG5A-4
0.75kW (1HP)
SV008iG5A-1
SV008iG5A-2
SV008iG5A-4
1.5kW (2HP)
SV015iG5A-1
SV015iG5A-2
SV015iG5A-4
2.2kW (3HP)
SV022iG5A-2
SV022iG5A-4
3.7kW (5HP)
SV037iG5A-2
SV037iG5A-4
4.0kW (5.4HP)
SV040iG5A-2
SV040iG5A-4
5.5kW (7.5HP)
SV055iG5A-2
SV055iG5A-4
7.5kW (10HP)
SV075iG5A-2
SV075iG5A-4
11.0kW (15HP)
SV110iG5A-2
SV110iG5A-4
15.0kW (20HP)
SV150iG5A-2
SV150iG5A-4
18.5kW (25HP)
SV185iG5A-2
SV185iG5A-4
22.0kW (30HP)
SV220iG5A-2
SV220iG5A-4
SV
015
iG5A
STARVERT
Motor rating (kW)
(004: 0.4kW~220: 22kW)
iG5A series
Input voltage
(1: 1 phase 200~230[V], 2: 3 phase 200~230[V], 4: 3 phase 380~480[V])
8
2
Compact & Powerful Drive iG5A
Standard Specifications
1 Phase 200V
SV
iG5A-1
004
008
0.5
1
2
0.4
0.75
1.5
0.95
1.9
3.0
(HP)
Max.
capacity 1)
(kW)
Capacity (kVA) 2)
FLA (A) 3)
Output
rating
3 phase 200~230V 5)
Max voltage
1phase 200~230 VAC (+10%, -15%)
Rated voltage
Input
rating
8
5
400 [Hz] 4)
2.5
Max frequency
015
50~60 [Hz] (±5%)
Rated frequency
Cooling method
Forced air cooling
Weight (kg)
1.84
1.12
0.76
3 Phase 200V
SV
iG5A-2
(HP)
Max.
capacity 1)
(kW)
Capacity (kVA)
2)
FLA (A) 3)
Output
rating
004
008
015
022
037
040
055
075
110
150
185
220
0.5
1
2
3
5
5.4
7.5
10
15
20
25
30
0.4
0.75
1.5
2.2
3.7
4.0
5.5
7.5
11
15
18.5
22
0.95
1.9
3.0
4.5
6.1
6.5
9.1
12.2
17.5
22.9
28.2
33.5
2.5
5
8
12
16
17
24
32
46
60
74
88
4)
400 [Hz]
3 phase 200~230V 5)
Max frequency
Max voltage
3 phase 200~230 (+10%, -15%)
Rated voltage
Input
rating
Rated frequency
Cooling method
Weight (kg)
50~60 [Hz] (±5%)
N/C 6)
0.76
0.77
1.12
1.84
1.89
1.89
004
008
015
022
037
Forced air cooling
3.66
3.66
9.0
9.0
13.3
13.3
040
055
075
110
150
185
220
3 Phase 400V
SV
Max.
capacity 1)
Output
rating
iG5A-4
(HP)
0.5
1
2
3
5
5.4
7.5
10
15
20
25
30
(kW)
0.4
0.75
1.5
2.2
3.7
4.0
5.5
7.5
11
15
18.5
22
Capacity (kVA) 2)
0.95
1.9
3.0
4.5
6.1
6.5
9.1
12.2
18.3
22.9
29.7
34.3
FLA (A)
1.25
2.5
4
6
8
9
16
24
30
39
45
9.0
9.0
13.3
13.3
3)
Max frequency
3 phase 380~480V 5)
Max voltage
Input
rating
Weight (kg)
3 phase 380~480 VAC (+10%, -15%)
Rated voltage
Rated frequency
Cooling method
12
400 [Hz] 4)
50~60 [Hz] (±5%)
N/C 6)
0.76
0.77
1.12
1.84
1.89
1.89
Forced air cooling
3.66
3.66
1) Indicate the maximum applicable motor capacity when using 4 pole LS standard motor.
2) Rated capacity is based on 220V for 200V series and 440V for 400V series.
3) Refer to 15-3 of userʼs manual when carrier frequency setting (39) is above 3kHz.
4) Max. frequency setting range is extended to 300Hz when H40 (Control mode select) is set to 3 (Sensorless vector control).
5) Max. output voltage cannot be higher than the input voltage. It can be programmable below input voltage.
6) Self-Cooling
Drive Starvert iG5A Series
9
iG5A
Control
Standard Specifications
Control method
V/F, Sensorless vector control
Frequency setting resolution
Digital command: 0.01Hz
Analog command: 0.06Hz (Max. freq.: 60Hz)
Frequency accuracy
Digital command: 0.01% of Max. output frequency
Analog command: 0.1% of Max. output frequency
V/F pattern
Linear, Squared, User V/F
Overload capacity
150% per 1 min.
Torque boost
Manual/Auto torque boost
Dynamic
braking
Max. braking
torque
20% 1)
Max. Duty
150% when using optional DB resistor 2)
Operation mode
Keypad/ Terminal/ Communication option/ Remote keypad selectable
Frequency setting
Analog: 0~10V, -10~10V, 0~20mA
Digital: Keypad
Operation features
PID, Up-down, 3-wire
NPN/PNP selectable
Operation
Input
Multi-function
terminal
P1~P8
Open collector
terminal
Output
Multi-function relay
Analog output (AM)
Protective
function
Environ
ment
FWD/REV RUN, Emergency stop, Fault reset, Jog operation, Multi-step Frequency-High, Mid, Low,
Multi-step Accel/Decel-High, Mid, Low, DC braking at stop, 2nd motor select, Frequency UP/Down,
3-wire operation, External trip A, B, PID-Drive (V/F) operation bypass,
Option-drive (V/F) operation bypass, Analog Hold, Accel/Decel stop
Fault output and
drive status output
(N.O., N.C.) Less than AC 250V, 1A; Less than DC 30V, 1A
0~10Vdc (less than 10mA): Output freq, Output current, Output voltage, DC link selectable
Trip
Over voltage, Under voltage, Over current, Ground fault current detection, Drive overheat,
Motor overheat, Output phase open, Overload protection, Communication error,
Loss of speed command, Hardware fault, Fan trip
Alarm
Stall prevention, Overload
Momentary power loss
Below 15 msec.: Continuous operation (Should be within rated input voltage, rated output power.)
Above 15 msec.: Auto restart enable
Protection degree
IP 20, NEMA1 (Optional)
Ambient temp
-10℃~50℃
Storage temp
-20℃~65℃
Humidity
Altitude/Vibration
Below 90% RH (No condensation)
Below 1,000m, 5.9m/sec 2 (0.6G)
Atmospheric pressure
70~106 kPa
Location
Protected from corrosive gas, Combustible gas, Oil mist or dust
1) Means average braking torque during Decel to stop of a motor.
2) Refer to Chapter 16 of userʼs manual for DB resistor specification.
10
Less than DC 24V, 50mA
Compact & Powerful Drive iG5A
Wiring
0.4~7.5kW
DB resistor
(Optional)
3 phase AC input
(Rated input voltage)
B1
B2
U
R
S
V
T
W
G
Ground
24 24V output
P1 FX (Forward run)
P2 RX (Reverse run)
AM
Multi-function
analog output
signal: 0~10V
CM
CM Input signal common
P3 BX (Emergency stop)
P4 RST (Trip reset)
P5 JOG (Jog operation)
3A A contact output
CM Input signal common
3C A/B contact common
P6 Multi-step freq. - Low
P7 Multi-step freq. - Middle
3B B contact output
P8 Multi-step freq. - High
MO Multi-function open
collector output
Potentiometer
(1kohm, 1/2W)
VR 10V power supply for potentiometer
V1 Freq. Setting Voltage signal input: -10~10V
I
Freq. Current signal input: 0~20mA
CM Input signal common
MG MO Common
S+
S-
RS-485 communication terminal
Drive Starvert iG5A Series
11
iG5A
Wiring
11.0~22.0kW
DC reactor
3 phase AC input
(Rated input voltage)
P1(+)
DB resistor
(Optional)
B1 B2
N(-)
R
U
S
V
T
W
G
Ground
24 24V output
AM
Multi-function
analog output
signal: 0~10V
P1 FX (Forward run)
P2 RX (Reverse run)
CM
CM Input signal common
P3 BX (Emergency stop)
P4 RST (Trip reset)
P5 JOG (Jog operation)
3A A contact output
CM Input signal common
3C A/B contact common
P6 Multi-step freq. - Low
P7 Multi-step freq. - Middle
3B B contact output
P8 Multi-step freq. - High
MO Multi-function open
collector output
Potentiometer
(1kohm, 1/2W)
VR 10V power supply for potentiometer
V1 Freq. Setting Voltage signal input: -10~10V
I
S+
Freq. Current signal input: 0~20mA
CM Input signal common
12
MG MO Common
S-
RS-485 communication terminal
Compact & Powerful Drive iG5A
Wiring
Specifications for power terminal block wiring
R
T
B1
B2
U
V
R
S
T
W
B1
B2
U
V
B2
U
W
V
R(L1)
R, S, T wire
SV0004iG5A-1
W
R
T
B1
• 2.2~4.0kW (3 phase)
R
S
• 11~22kW (3 phase)
• 5.5kW~7.5kW (3 phase)
B1
• 1.5kW (1 phase)
• 0.4kW~1.5kW (3 phase)
• 0.4kW~0.75kW (1 phase)
U, V, W wire
S(L2)
T(L3) P1(+)
Ground wire
B2
U
V
W
T
B1
B2
U
V
W
B1
B2
N(-)
U
V
W
mm2
AWG
mm2
AWG
mm2
AWG
Terminal
Screw Size
Screw Torque
(kgf.cm) / lb-in
2
14
2
14
3.5
12
M3.5
10/8.7
SV0008iG5A-1
2
2
14
3.5
12
M3.5
10/8.7
SV0015iG5A-1
14
2
14
2
14
3.5
12
M4
15/13
SV0004iG5A-2
2
2
14
3.5
12
M3.5
10/8.7
SV0008iG5A-2
14
2
14
2
14
3.5
12
M3.5
10/8.7
SV0015iG5A-2
2
2
14
3.5
12
M3.5
10/8.7
SV0022iG5A-2
14
2
14
2
14
3.5
12
M4
15/13
SV0037iG5A-2
3.5
3.5
12
3.5
12
M4
15/13
SV0040iG5A-2
12
3.5
12
3.5
12
3.5
12
M4
15/13
SV0055iG5A-2
5.5
5.5
10
5.5
10
M5
32/28
SV0075iG5A-2
10
8
8
8
8
5.5
10
M5
32/28
SV0110iG5A-2
14
14
6
14
6
M6
30.7/26.6
SV0150iG5A-2
6
22
22
4
14
6
M6
30.7/26.6
SV0185iG5A-2
4
30
2
30
2
22
4
M8
30.5/26.5
SV0220iG5A-2
38
30
2
22
4
M8
30.5/26.5
SV0004iG5A-4
2
2
14
2
14
2
14
M3.5
10/8.7
SV0008iG5A-4
2
2
14
2
14
M3.5
10/8.7
SV0015iG5A-4
14
2
14
2
14
2
14
M4
15/13
SV0022iG5A-4
2
2
14
2
14
M4
15/13
SV0037iG5A-4
14
2
14
2
14
2
14
M4
15/13
SV0040iG5A-4
2
2
14
2
14
M4
15/13
SV0055iG5A-4
14
3.5
12
2
14
3.5
12
M5
32/28
SV0075iG5A-4
3.5
12
3.5
12
3.5
12
M5
32/28
10
8
8
M5
30.7/26.6
30.7/26.6
SV0110iG5A-4
5.5
SV0150iG5A-4
10
5.5
14
8
8
8
8
M5
SV0185iG5A-4
6
14
6
8
8
14
6
M6
30.5/26.5
SV0220iG5A-4
22
4
14
6
14
6
M6
30.5/26.5
Drive Starvert iG5A Series
13
iG5A
Terminal Configuration
Control terminal specifications
MO MG
3A
Terminal
P1~P8
3B
3C
Description
Multi-function input T/M 1-8
24
P5
CM
P1
P6
P2
CM
P7
P8
Wire size (mm2)
P3
VR
P4
S-
S+
I
AM
V1
Torque (Nm)
1.5
M2.6
0.4
1.5
M2.6
0.4
Stranded
1.0
1.0
Specification
CM
Common terminal
VR
Power supply for external
potentiometer
1.0
1.5
M2.6
0.4
V1
Input terminal for voltage operation
1.0
1.5
M2.6
0.4
Max. input voltage:
-12V~+12V input
I
Input terminal for current operation
1.0
1.5
M2.6
0.4
0~20mA input
Internal resistor: 500ohm
AM
Multi-function analog output terminal
1.0
1.5
M2.6
0.4
Max. output voltage: 11V
Max. output current: 100mA
MO
Multi-function terminal for open collector
1.0
1.5
M2.6
0.4
Below DC 26V,100mA
Ground terminal for external power supply
1.0
1.5
M2.6
0.4
24V external power supply
1.0
1.5
M2.6
0.4
Max. output current: 100mA
Multi-function relay output A contact
1.0
1.5
M2.6
0.4
Below AC 250V, 1A
Multi-function relay output B contact
1.0
1.5
M2.6
0.4
Below DC 30V, 1A
Common for multi-function relays
1.0
1.5
M2.6
0.4
MG
24
3A
3B
3C
1) Use the recommended tightening torque when securing terminal screws.
※ When you use external power supply (24V) for multi-function input terminal (P1~P8), apply voltage higher than 12V to activate.
※ Tie the control wires more than 15cm away from the control terminals. Otherwise, it interferes front cover reinstallation.
14
1)
Screw size
Single wire
Output voltage: 12V
Max. output current: 100mA
Potentiometer: 1~5kohm
Compact & Powerful Drive iG5A
Keypad Features
Display
KEY
LED
1)
Description
Term
RUN
Run key
Run command
STOP/RESET
STOP/RESET key
STOP: Stop command during operation,
RESET: Reset command when a fault occurs.
▲
Up key
Down key
Used to scroll through codes or increase parameter value
▼
▶
Right key
Used to jump to other parameter groups or move a cursor to
the right to change the parameter value
◀
Left key
Used to jump to other parameter groups or move a cursor to
the left to change the parameter value
●
Enter key
FWD
Forward run
Used to set the parameter value or save the changed parameter value
REV
Reverse run
Lit during reverse run
Run key
Lit during operation
Setting
Lit during parameter setting
RUN
SET
Used to scroll through codes or decrease parameter value
Lit during forward run
1) 4 LEDs above are set to blink when a fault occurs.
ENT
RESET
65.6
STOP
RUN
2-Φ4.5
36.2
FWD
REV
72.4
SET
RUN
3.4
95
83
70
C
L
Dimensions
5
2.1
13.9
23.1
Drive Starvert iG5A Series
15
iG5A
Moving to Other Groups
Parameter groups
There are 4 different parameter groups in iG5A series as shown below.
Parameter group
Description
Drive group
Basic parameters necessary for the drive to run. Parameters such as Target frequency, Accel/Decel time settable.
Function group 1
Basic function parameters to adjust output frequency and voltage.
Function group 2
Advanced function parameters to set parameters for such as PID Operation and second motor operation.
I/O (Input/Output) group
Parameters necessary to make up a sequence using multi-function input/output terminal.
Moving to other groups
Moving to other groups using the Right (▶) key
Moving to other groups using the Left (◀) key
1)
1) Target frequency can be set at 0.0 (the 1st code of drive group). Even though the preset value is 0.0, it is user-settable.
The changed frequency will be displayed after it is changed.
16
1)
Compact & Powerful Drive iG5A
When changing ACC time from 5.0 sec to 16.0 sec
1
2
•In the first code “0.00”, press the Up (▲) key once to go to the second code.
•ACC [Accel time] is displayed.
•Press the Ent (●) key once.
3
•Preset value is 5.0, and the cursor is in the digit 0.
•Press the Left (◀) key once to move the cursor to the left.
4
•The digit 5 in 5.0 is active. Then press the Up (▲) key once.
5
•The value is increased to 6.0
•Press the Left (◀) key to move the cursor to the left.
6
•0.60 is displayed. The first 0 in 0.60 is active.
•Press the Up (▲) key once.
7
•16.0 is set.
•Press the Ent (●) key once.
•16.0 is blinking. 1)
•Press the Ent (●) key once again to return to the parameter name.
8
•ACC is displayed. Accel time is changed from 5.0 to 16.0 sec.
1) Pressing the Left (◀)/Right (▶)/Up (▲)/Down (▼) key while a cursor is blinking will cancel the parameter value change.
Pressing the Ent (●) key in this status will enter the value into memory.
※ In step 7, pressing the Left (◀) or Right (▶) key while 16.0 is blinking will disable the setting.
Code change in Drive group
1
•In the 1st code in Drive group “0.00”,
press the Up (▲) key once.
2
•The 2nd code in Drive group “ACC”is displayed.
•Press the Up (▲) key once.
3
•The 3rd code “dEC” in Drive group is displayed.
•Keep pressing the Up (▲) key until the last code appears.
4
•The last code in Drive group “drC” is displayed.
•Press the Up (▲) key again.
5
•Return to the first code of Drive group.
•Use Down (▼) key for the opposite order.
Drive Starvert iG5A Series
17
iG5A
Trial Run
Multi-step operation + Run/Stop via FX/RX + Max. frequency change
Operation condition
Operation command:
Run/Stop via FX/RX
Frequency command:
Multi-step operation [Low (20), Middle (30), High (80)]
Max. frequency change:
From 60Hz to 80Hz
Wiring
P1 (Forward)
S1
P2 (Reverse)
S2
3 phase
AC input
P6 (Low)
S3
S
V
T
W
S/W
P8 (High)
S5
U
G
P7 (Middle)
S4
R
P1 (Forward)
P2 (Reverse)
CM
P6 (Low)
P7 (Middle)
P8 (High)
CM
1. Please make sure that R, S, T are connected to 3 phase AC input, and
U, V, W are also motor connection terminals.
2. After supplying the power, please set the frequency of multi-step among
Low, Middle, and High.
VR
3. If P1 (FX) turns on, the motor operates in forward. And after turning off,
it stops according to the deceleration time.
CM
V1
4. If P2 (RX) turns on, the motor operates in reverse. And after turning off,
it stops according to the deceleration time.
Parameter setting
18
Step
Command
Code
Default
After change
1
Max. frequency change (FU1)
F21
Change Max. frequency.
Description
60Hz
80Hz
2
Multi-step frequency (DRV)
st1
Set ‛Low’ step.
10Hz
20Hz
3
Multi-step frequency (DRV)
st2
Set ‛Middle’ step.
20Hz
30Hz
4
Multi-step frequency (I/O)
I30
Set ‛High’ step.
30Hz
80Hz
5
Forward run (P1: FX)
I17
The default is FX. This value may change.
FX
FX
6
Reverse run (P2: RX)
I18
The default is RX. This value may change.
RX
RX
Compact & Powerful Drive iG5A
Potentiometer (Volume) + Run/Stop via FX/RX + Accel/Decel time change
Operation condition
Operation command:
Run/Stop via FX/RX
Frequency command:
0~60Hz analog input via potentiometer
Accel/Decel time:
Accel-10sec, Decel-20sec
Wiring
Potentiometer 1~5kohm, 1/2W
3
2
Motor
VR
R
S
T
G
3 phase
AC input
V1
1
CM
U
V
W
0~60Hz
P1 (FX) Forward
P2 (RX) Reverse
CM
1. Please make sure that R, S, T are connected to 3 phase AC input,
and U, V, W are also motor connection terminals.
2. After supplying the power, please set the frequency of multi-step
among Low, Middle, and High.
3. If P1 (FX) turns on, the motor operates in forward. And after
turning off, it stops according to the deceleration time.
VR
V1
CM
Potentiometer
1~5kohm, 1/2W
4. If P2 (RX) turns on, the motor operates in reverse. And after
turning off, it stops according to the deceleration time.
5. Control the motorʼs speed via potentiometer.
Parameter setting
Step
Command
Code
Description
1
Operation command
(DRV group)
Drv
Turn on/off motor via terminal.
1 (FX/RX-1)
1 (FX/RX-1)
2
Analog input
(DRV group)
Frq
Change keypad command to analog voltage command.
0 (Keypad-1)
3 (V1: 0~10V)
3
Accel/Decel time
(DRV group)
ACC
dEC
Set Accel time to 10sec in ACC
5sec (Accel)
10sec (Decel)
10sec (Accel)
20sec (Decel)
4
Forward run
(P1: FX)
I17
The default is FX. This value may change
FX
FX
5
Reverse run
(P2: RX)
I18
The default is RX. This value may change.
RX
RX
Set Decel time to 20sec in dEC.
Default
After change
Drive Starvert iG5A Series
19
iG5A
Dimensions
SV004iG5A-2 / SV008iG5A-2, SV004iG5A-4 / SV008iG5A-4
W
A
A
W1
H1
Φ
H
D
B
W1
mm (inches)
Drive model
(kW)
W (mm)
W1 (mm)
H (mm)
H1 (mm)
D (mm)
SV004IG5A-2
SV008IG5A-2
SV004IG5A-4
SV008IG5A-4
0.4
0.75
0.4
0.75
70
70
70
70
65.5
65.5
65.5
65.5
128
128
128
128
119
119
119
119
130
130
130
130
Φ
4.0
4.0
4.0
4.0
A (mm)
B (mm)
(kg)
4.5
4.5
4.5
4.5
4.0
4.0
4.0
4.0
0.76
0.77
0.76
0.77
SV015iG5A-2 / SV015iG5A-4
W
W1
A1
A
H1
Φ
H
D
B
W1
mm (inches)
20
Drive model
(kW)
W (mm)
W1 (mm)
H (mm)
H1 (mm)
D (mm)
Φ
A (mm)
B (mm)
(kg)
SV015IG5A-2
SV015IG5A-4
1.5
1.5
100
100
95.5
95.5
128
128
120
120
130
130
4.5
4.5
4.5
4.5
4.5
4.5
1.12
1.12
Compact & Powerful Drive iG5A
SV022iG5A-2 / SV037iG5A-2 / SV040iG5A-2, SV022iG5A-4 / SV037iG5A-4 / SV040iG5A-4
W
A
Φ
H1
C
L
H
D
B
B
W1
mm (inches)
Drive model
(kW)
W (mm)
W1 (mm)
H (mm)
H1 (mm)
D (mm)
Φ
A (mm)
B (mm)
(kg)
SV022IG5A-2
SV037IG5A-2
SV040IG5A-2
SV022IG5A-4
SV037IG5A-4
SV040IG5A-4
2.2
3.7
4.0
2.2
3.7
4.0
140
140
140
140
140
140
132
132
132
132
132
132
128
128
128
128
128
128
120.5
120.5
120.5
120.5
120.5
120.5
155
155
155
155
155
155
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
4.5
1.84
1.89
1.89
1.84
1.89
1.89
SV055iG5A-2 / SV075iG5A-2, SV055iG5A-4 / SV075iG5A-4
W
A
Φ
W
A
H1
H
D
B
B
W
mm (inches)
Drive model
(kW)
W (mm)
W1 (mm)
H (mm)
H1 (mm)
D (mm)
Φ
A (mm)
B (mm)
(kg)
SV055IG5A-2
SV075IG5A-2
SV055IG5A-4
SV075IG5A-4
5.5
7.5
5.5
7.5
180
180
180
180
170
170
170
170
220
220
220
220
210
210
210
210
170
170
170
170
4.5
4.5
4.5
4.5
5
5
5
5
4.5
4.5
4.5
4.5
3.66
3.66
3.66
3.66
Drive Starvert iG5A Series
21
iG5A
Dimensions
SV110iG5A-2 / SV150iG5A-2 / SV110iG5A-4 / SV150iG5A-4
W
A
W1
Φ
A
H1
H
D
B
B
W1
mm (inches)
Drive model
(kW)
W (mm)
W1 (mm)
H (mm)
H1 (mm)
D (mm)
Φ
A (mm)
B (mm)
(kg)
SV110iG5A-2
SV150iG5A-2
SV110iG5A-4
SV150iG5A-4
11.0
15.0
11.0
15.0
235
235
235
235
219
219
219
219
320
320
320
320
304
304
304
304
189.5
189.5
189.5
189.5
7.0
7.0
7.0
7.0
8.0
8.0
8.0
8.0
7.0
7.0
7.0
7.0
9.00
9.00
9.00
9.00
SV0185iG5A-2 / SV0220iG5A-2 / SV0185iG5A-4 / SV0220iG5A-4
W
Φ A
W1
A
H1
H
D
B
W1
B
mm (inches)
22
Drive model
(kW)
W (mm)
W1 (mm)
H (mm)
H1 (mm)
D (mm)
Φ
A (mm)
B (mm)
(kg)
SV185iG5A-2
SV220iG5A-2
SV185iG5A-4
SV220iG5A-4
18.5
22.0
18.5
22.0
260
260
260
260
240
240
240
240
410
410
410
410
392
392
392
392
208.5
208.5
208.5
208.5
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
13.3
13.3
10.0
10.0
Compact & Powerful Drive iG5A
Braking Resistors and Peripheral Devices
Braking resistors
Voltage
100% braking
Drive
Resistor [Ω]
400
200
100
60
40
30
20
15
11
9
8
1,800
900
450
300
200
120
90
60
45
35
30
0.4
0.75
1.5
2.2
3.7
5.5
7.5
11.0
15.0
18.5
22.0
0.4
0.75
1.5
2.2
3.7
5.5
7.5
11.0
15.0
18.5
22.0
200V Series
400V Series
Watt [W]1)
50
100
200
300
500
700
1,000
1,400
2,000
2,400
2,800
50
100
200
300
500
700
1,000
1,400
2,000
2,400
2,800
150% braking
Resistor [Ω]
300
150
60
50
33
20
15
10
8
5
5
1,200
600
300
200
130
85
60
40
30
20
20
Watt [W] 1)
100
150
300
400
600
800
1,200
2,400
2,400
3,600
3,600
100
150
300
400
600
1,000
1,200
2,000
2,400
3,600
3,600
1) The wattage is based on Enable Duty (%ED) with continuous braking time 15sec.
Breakers
Voltage
1-Phase
200V
3-Phase
200V
3-Phase
400V
Capacity
[kW]
0.4
0.75
1.5
0.4
0.75
1.5
2.2
3.7
4
5.5
7.5
11
15
18.5
22
0.4
0.75
1.5
2.2
3.7
4
5.5
7.5
11
15
18.5
22
Model
Circuit Breaker (MCCB)
Model
Rated Current [A]
ABS33c
UTE100
ABS33c
ABS53c
ABS63c
ABS103c
ABS203c
ABS33c
ABS53c
ABS63c
ABS103c
5
10
15
5
10
15
20
30
30
50
60
100
125
150
175
3
5
10
10
15
20
30
30
50
60
75
100
UTE100
UTS150
UTS250
UTE100
Rated Current [A]
15
15
15
15
15
15
20
30
30
50
60
90
125
150
175
15
15
15
15
15
20
30
30
50
60
80
90
Leakage Breaker (ELCB)
Model
Rated Current [A]
EBS33c
EBS33c
EBS53c
EBS63c
EBS103c
EBS203c
EBS33c
EBS53c
EBS63c
EBS103c
5
10
15
5
10
15
20
30
30
50
60
100
125
150
175
5
5
10
10
15
20
30
30
50
60
75
100
Note) 1. The capacity of the MCCB should be 1.5 to 2 times the rated output current of the drive.
2. Use an MCCB keep the drive from faulting out instead of using overheat protection (150% for one minute at the rated output current.)
3. In case magnetic contactor is used on single-phase product, wire R and T phases.
Magnetic Contactor (MC)
Model
Rated Current [A]
MC-6a
9
MC-9a, MC-9b
11
MC-18a, MC-18b
18
MC-6a
9
MC-9a, MC-9b
11
MC-18a, MC-18b
18
MC-22b
22
32
MC-32a
32
MC-50a
55
MC-65a
65
MC-85a
85
MC-130a
130
MC-150a
150
MC-185a
185
7
MC-6a
7
MC-9a, MC-9b
9
MC-12a, MC-12b
12
18
MC-18a, MC-18b
18
MC-22b
22
MC-32a
32
MC-50a
50
MC-65a
65
MC-75a
75
MC-85a
85
Drive Starvert iG5A Series
23
iG5A
Braking Resistors and Peripheral Devices
Fuses & AC reactors
Model
004iG5A-1
008iG5A-1
015iG5A-1
004iG5A-2
008iG5A-2
015iG5A-2
022iG5A-2
037iG5A-2
040iG5A-2
055iG5A-2
075iG5A-2
110iG5A-2
150iG5A-2
185iG5A-2
220iG5A-2
004iG5A-4
008iG5A-4
015iG5A-4
022iG5A-4
037iG5A-4
040iG5A-4
055iG5A-4
075iG5A-4
110iG5A-4
150iG5A-4
185iG5A-4
220iG5A-4
24
AC external fuse
Current [A]
10 A
10 A
15 A
10 A
10 A
15 A
25 A
30 A
30 A
30 A
50 A
70 A
100 A
100 A
125 A
5A
10 A
10 A
10 A
20 A
20 A
20 A
30 A
35 A
45 A
60 A
70 A
Voltage [V]
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
600V
AC reactor
DC reactor
4.20 mH, 3.5 A
2.13 mH, 5.7 A
1.20 mH, 10 A
4.20 mH, 3.5 A
2.13 mH, 5.7 A
1.20 mH, 10 A
0.88 mH, 14 A
0.56 mH, 20 A
0.56 mH, 20 A
0.39 mH, 30 A
0.28 mH, 40 A
0.20 mH, 59 A
0.15 mH, 75 A
0.12 mH, 96 A
0.10 mH, 112 A
18.0 mH, 1.3 A
8.63 mH, 2.8 A
4.81 mH, 4.8 A
3.23 mH, 7.5 A
2.34 mH, 10 A
2.34 mH, 10 A
1.22 mH, 15 A
1.14 mH, 20 A
0.81 mH, 30 A
0.61 mH, 38 A
0.45 mH, 50 A
0.39 mH, 58 A
0.74 mH, 56 A
0.57 mH, 71 A
0.49 mH, 91 A
0.42 mH, 107 A
2.76 mH, 29 A
2.18 mH, 36 A
1.79 mH, 48 A
1.54 mH, 55 A
Compact & Powerful Drive iG5A
Function List
Drive Group
LED
display
Address for
communication
Parameter
name
Min/Max
range
dEC
A100
[Frequency 0 ~ 400
command][Hz]
A101
[Accel time]
A102
[Decel time]
0 ~ 6000
[Sec]
A103
[Drive mode]
0~3
A104
[Frequency setting method]
0~7
A105
A106
frequency 1]
[Multi-Step frequency 2]
St3
[Multi-Step
A107
frequency 3]
CUr
A108
[Output current]
rPM
A109
[Motor RPM]
A10A
vOL
A10B
FX: Run/Stop enable
10.0
O
1
X
Keypad setting 1
3
V1 2: 0 ~ +10 [V]
4
RX: Reverse rotation select
Digital
1
Analog
5
Keypad setting 2
V1 1: -10 ~ +10 [V]
Terminal I: 0 ~ 20 [mA]
Terminal V1 setting 1 + Terminal I
Terminal V1 setting 2+ Terminal I
7
RS485 communication
9
Set to Field Bus communication 1)
8
[Multi-Step RX: Motor reverse run
Set to Field Bus communication 1)
6
FX: Motor forward run
RS485 communication
2
dCL
O
Run/Stop via Run/Stop key on the keypad
1
Terminal operation
2
0
5.0
Accel/Decel time 0.
4
St2
During Multi-Accel/Decel operation, this parameter serves as
3
St1
O
During Multi-step operation:
0
Frq
During Run: Output Frequency
It cannot be set greater than F21- [Max frequency].
drv
During Stop: Frequency Command
Multi-step frequency 0.
0.00
to output.
ACC
Adj.
during run
This parameter sets the frequency that the drive is commanded
0.00
Factory
defaults
Description
[Hz]
[Drive DC
link voltage]
[User display
select]
Torque
30.00
O
-
-
-
-
-
-
vOL
-
This parameter displays the item selected at H73- [Monitoring
tOr
O
Displays DC link voltage inside the drive.
Output power
20.00
Displays the number of Motor RPM.
Output voltage
10.00O
Displays the output current to the motor.
POr
Sets Multi-Step frequency 3 during Multi-step operation.
vOL
Sets Multi-Step frequency 2 during Multi-step operation.
item select].
X
Digital Volume
Sets Multi-Step frequency 1 during Multi-step operation.
0 ~ 400
0
1) This function can be available with iG5A Communication Option Module.
Drive Starvert iG5A Series
25
iG5A
Function List
Drive Group
LED
display
nOn
Address for
communication
Parameter
name
A10C
[Fault Display]
drC
A10D
Min/Max
range
Displays the types of faults, frequency and operating status at
the time of the fault
A10E
motor rotation select]
F, r
to either 0 or 1.
F
r
0
[Drive mode 2]
0~3
4
0
Frq2 1) A10F
[Frequency setting 0~7
method 2]
Run/Stop via Run/Stop key on the keypad
RX: Motor reverse run
FX: Run/Stop enable
RX: Reverse rotation select
RS-485 communication
Set to Filed Bus Communication 3)
Terminal I: 0 ~ 20 [mA]
Terminal V1 setting 2+ Terminal I
7
RS485 communication
9
Set to Filed Bus Communication 3)
Digital Volume
If H58 is 0, it is expressed as a [Hz] unit.
PID control
If H58 is 1, it is expressed as a [%] unit.
It indicates a feedback amount in PID control.
0
X
0.00
0
-
-
Factory
defaults
Adj.
during run
Sets the parameter code number to jump.
1
O
0
Fwd and rev run enable
Reverse run disable
If H58 is 0, it is expressed as a [Hz] unit.
If H58 is 1, it is expressed as a [%] unit.
amount
Analog
5
In [Hz] unit, you canʼt set Max. frequency more than (F21).
0~100 [%]
In [%] unit, 100% means Max. frequency.
Terminal V1 setting 1 + Terminal I
4
value setting
feedback
X
Fbk 2) A111
1
V1 2: 0 ~ +10 [V]
V1 1: -10 ~ +10 [V]
0~400[Hz]
or
O
3
Keypad setting 2
PID control standard F
Keypad setting 1
A110
-
Digital
1
8
-
FX: Motor forward run
6
2)
Reverse
2
rEF
Forward
1
Terminal operation
2
3
Adj.
during run
Sets the direction of motor rotation when drv - [Drive mode] is set [Direction of drv2
Factory
defaults
Description
1) Only displayed when one of the Multi-function input terminals 1-8 [I17~I24] is set to “22”.
2) It is indicated when H49(PID control selection) is 1.
3) This function can be available with iG5A Communication Option Module.
Function group 1
LED
display
F0
F1
F2
F3
26
Address for
communication
Parameter
name
Min/Max
range
A200
[Jump code]
0 ~ 71
[Forward/ A201
Reverse run A202
[Accel pattern]
A203
[Decel pattern]
0~2
Description
1
2
disable]
0~1
Forward run disable
0
Linear
1
S-curve
0
X
0
X
Compact & Powerful Drive iG5A
Function group 1
LED
display
Address for
communication
Parameter
name
Min/Max
range
A204
[Stop mode
F 8 1) A208
[DC Brake 0.1 ~ 60
[DC Brake 0 ~ 60
[DC Brake 0 ~ 200
F4
A209
F9
A20A
F10
A20B
F11
select]
start frequency]
wait time]
0~3
[Hz]
[sec]
voltage] [%]
[DC Brake time]
0 ~ 60
[sec]
[DC Brake start 0 ~ 200
F12
A20C
F13
[DC Brake start 0 ~ 60
A20D
time] [sec]
F14
A20E
voltage][%]
[Time for magnetizing a motor]
A214
[Jog frequency]
F20
0 ~ 60
[sec]
0 ~ 400
[Hz]
A215
[Max frequency]
F21 2) 40 ~ 400
A216
[Base frequency]
30 ~ 400
F22
A217
[Start frequency]
F23
A218
F24
F25
F26
F27
F28
F29
3)
A219
A21A
A21B
A21C
[Frequency high
/low limit select]
[Hz]
[Hz]
0.1 ~ 10
[Hz]
0~1
[Frequency 0 ~ 400
[Frequency 0.1 ~ 400
high limit]
low limit]
[Torque Boost select]
[Torque boost in forward direction]
[Torque boost A21D
in reverse direction]
[Hz]
[Hz]
0~1
0 ~ 15
[%]
Description
Factory
defaults
Adj.
during run
0
Decelerate to stop
2
Free run to stop
0
X
5.00
X
0.1
X
50
X
motor while motor is at a stop.
1.0
X
starts to run.
50
X
0
X
1
3
DC brake to stop
Power Braking stop
This parameter sets DC brake start frequency.
It cannot be set below F23 - [Start frequency].
When DC brake frequency is reached, the drive holds the output
for the setting time before starting DC brake.
This parameter sets the amount of DC voltage applied to a motor.
It is set in percent of H33 - [Motor rated current].
This parameter sets the time taken to apply DC current to a
This parameter sets the amount of DC voltage before a motor
It is set in percent of H33 - [Motor rated current].
DC voltage is applied to the motor for DC Brake start time before
motor accelerates.
This parameter applies the current to a motor for the set time
before motor accelerates during Sensorless vector control.
0.1
X
10.00
O
This parameter sets the frequency for Jog operation.
It cannot be set above F21 - [Max frequency].
This parameter sets the highest frequency the drive can output.
It is frequency reference for Accel/Decel (See H70)
60.00
Caution
X
Any frequency cannot be set above Max frequency except Base frequency
The drive outputs its rated voltage to the motor at this frequency
60.00
X
0.50
X
0
X
It cannot be set above F21 - [Max frequency].
60.00
X
It cannot be set above F25 - [Frequency high limit] and below
0.50
X
(see motor nameplate).
The drive starts to output its voltage at this frequency.
It is the frequency low limit.
This parameter sets high and low limit of run frequency.
This parameter sets high limit of the run frequency.
This parameter sets low limit of the run frequency.
F23 - [Start frequency].
0
1
Manual torque boost
Auto torque boost
This parameter sets the amount of torque boost applied to a motor
during forward run. It is set in percent of Max output voltage.
This parameter sets the amount of torque boost applied to a motor
during reverse run. It is set as a percent of Max output voltage.
1) Only displayed when F 4 is set to 1 (DC brake to stop).
2) If H40 is set to 3 (Sensorless vector), Max. frequency is settable up to 300Hz.
3) Only displayed when F24 (Frequency high/low limit select) is set to 1.
0
X
2
X
2
X
Drive Starvert iG5A Series
27
iG5A
Function List
Function group 1
LED
display
F30
F31 1)
F32
F33
F34
F35
F36
F37
F38
F39
F40
F50
Address for
communication
A21E
[V/F pattern]
A21F
frequency 1]
A220
A221
A222
A223
A224
A225
A226
A232
A233
A234
F54
F55
[Hz]
[User V/F ]
0 ~ 100
voltage 1
[User V/F 0 ~ 100
[User V/F [User V/F [User V/F A235
A236
A237
[Electronic 0~1
above those of higher-numbered.
50 ~ 200
[%]
[%]
This parameter adjusts the amount of output voltage.
The set value is the percentage of input voltage.
This parameter decreases output voltage according to load
status.
This parameter is activated when the motor is overheated (timeinverse).
continuously for 1 minute.
The set value is the percentage of H33 - [Motor rated current].
It cannot be set below F52 - [Electronic thermal level for
This parameter sets the amount of current to keep the motor
running continuously.
It cannot be set higher than F51 - [Electronic thermal level for 1
minute].
Standard motor having cooling fan directly connected to
0
the shaft
[Motor cooling warning level]
[Overload warning time]
30 ~ 150
[%]
0 ~ 30
[Sec]
X
30.00
X
50
X
45.00
X
75
X
60.00
X
100
X
100
X
0
0
0
0
150
0
1000
0
0
signal at a relay or multi-function output terminal (see I54, I55).
150
0
This parameter issues an alarm signal when the current greater
0~1
method]
1A motor using a separate motor to power a cooling fan.
[Overload 25
continuous].
50 ~ 150
X
This parameter sets max current capable of flowing to the motor
thermal level for
continuous]
voltage].
0 ~ 100
thermal select]
15.00
The values of the lower-numbered parameters cannot be set
[%]
[Hz]
[User V/F thermal level for
It cannot be set above F21 - [Max frequency].
0 ~ 400
voltage 4]
[Electronic
[Hz]
[%]
frequency 4] 1 minute]
{User V/F}
{Square}
The value of voltage is set in percent of H70 - [Motor rated
0 ~ 100
voltage 3]
[Electronic 2
1
[%]
0 ~ 400
frequency 3]
X
[Hz]
[User V/F 0
{Linear}
0 ~ 400
voltage 2]
Adj.
during run
0
[%]
frequency 2]
Factory
defaults
Description
0 ~ 400 It is used only when V/F pattern is set to 2(User V/F)
[User V/F 1) Set F30 to 2(User V/F) to display this parameter.
2) Set F50 to 1 to display this parameter.
28
0~2
[Energy-saving 0 ~ 30
A228
level] [%]
F53
Min/Max
range
[Output voltage 40 ~ 110
A227
adjustment][%]
F51 2) F52
Parameter
name
This parameter sets the amount of current to issue an alarm
The set value is the percentage of H33- [Motor rated current].
than F54- [Overload warning level] flows to the motor for F55[Overload warning time].
10
0
Compact & Powerful Drive iG5A
Function group 1
LED
display
F56
F57
F58
Address for
communication
A238
A239
A23A
Parameter
name
Min/Max
range
[Overload 0~1
trip select]
[Overload
30 ~ 200
[Overload 0 ~ 60
trip level]
[%]
trip time]
[Sec]
Factory
defaults
Adj.
during run
1
0
The value is the percentage of H33- [Motor rated current].
180
0
[Overload trip level] of current flows to the motor for F58-
60
0
Description
This parameter turns off the drive output when motor is
overloaded.
This parameter sets the amount of overload current.
This parameter turns off the drive output when the F57[Overload trip time].
during deceleration.
A23B
[Stall prevention
select]
0~7
-
-
6
A23C
5
A23F
[Stall prevention
level]
30 ~ 200
[%]
[When Stall limit select
[Save up/down
frequency select]
0~1
0~1
[Up-down mode
A241
select]
A242
[Up-down step 0~2
0~400
frequency][Hz]
[Draw rate]
0
-
0~100[%]
X
-
-
This parameter sets the amount of current to activate stall
150
prevention function during Accel, Constant or Decel run.
X
The set value is the percentage of the H33- [Motor rated current]. In Stall prevention run during deceleration, if you want to limit
output voltage, select 1
This parameter decides whether to save the specified frequency
during up/down operation.
When 1 is selected, the up/down frequency is saved in F64.
Increases goal frequency as a standard of Max.
0
frequency/Min. frequency
1
2
In case of choosing F65 as a 1 or 2, it means increase or
decrease of frequency according to up-down input
0
Drive doesnʼt run as a draw mode
2
I(0~20mA) input draw run
1
3
V1(0~10V) input draw run
V1(-10~10V) input draw run
Sets rate of draw
X
0.00
X
0
Increases as many as step frequency according to edge input
Available to combine 1 and 2
0
We can select up-down mode among three thing
A247
-
saves the frequency before the drive stops or decelerated.
[Draw run mode A246
0~3
select]
-
Bit 0
If ʻSave up/down frequencyʼ is selected at F63, this parameter
-
7
[Save up/down
F64 2) A240
frequency]
F71
-
-
prevention during A23D
F61 1)
deceleration, voltage
F70
-
-
During constant run During Accel
Bit 1
4
F66
1
2
During Decel
Bit 2
F65
0
3
F63
decelerating during constant speed run and stops decelerating
F60
This parameter stops accelerating during acceleration,
F59
X
0.00
X
0
X
0.00
0
1) It is indicated when setting bit 2 of F59 as 1
2) Set F63 to 1 to display this parameter.
Drive Starvert iG5A Series
29
iG5A
Function List
Function group 2
LED
display
H0
H1
H2
H3
H4
H5
H6
Address for
communication
Parameter
name
Min/Max
range
A300
[Jump code]
0~95
A302
A301
A303
A304
A305
A306
H7
H8
H10
H11 1)
H12
H13
H14
H15
H16
H17
H18
H19
H21
-
[Fault history 3]
Stores information on the types of faults, the frequency, the
-
latest fault is automatically stored in the H 1- [Fault history 1].
-
[Fault history 4]
[Fault history 5]
-
[Reset fault 0~1
history]
A308
[Dwell time]
A30A
[Skip frequency A30B
[Skip frequency A30C
[Skip frequency
A30D
A30E
A30F
current and the Accel/Decel condition at the time of fault. The
0~1
[Skip frequency
low limit 2]
[Skip frequency [Hz]
high limit 2]
[Dwell frequency] can be set within the range of F21- [Max
frequency] and F23- [Start frequency].
Sets the frequency range to skip to prevent undesirable
resonance and vibration on the structure of the machine.
The frequency values of the low numbered parameters cannot
be set above those of the high numbered ones. Settable within
the range of F21 and F23.
[Skip frequency
[Skip frequency
[S-Curve accel/
1~100
Set the speed reference value to form a curve at the start during
[S-Curve accel/
1~100
Set the speed reference value to form a curve at the end during
A311
A312
A313
low limit 3]
high limit 3]
decel start side]
decel end side]
[Input/output phase loss protection select]
A314
Start select]
[Restart after A315
[Power On fault reset selection]
[%]
accel/decel. If it is set higher, linear zone gets smaller.
[%]
accel/decel. If it is set higher, linear zone gets smaller.
0~3
0~1
0
Disabled
1
Output phase protection
Input phase Input/output phase 2
3
protection protection
This parameter is activated when drv is set to 1 or 2 (Run/Stop
via Control terminal).
Motor starts acceleration after AC power is applied while FX or
-
nOn
-
nOn
nOn
nOn
O
5.00
X
0.0
X
0
X
10.00
X
15.00
X
20.00
X
25.00
X
30.00
X
35.00
X
40
X
40
X
0
O
0O
RX terminal is ON.
This parameter is activated when drv is set to 1 or 2 (Run/Stop
0 ~1
via Control terminal).
Motor accelerates after the fault condition is reset while the FX or
RX terminal is ON.
1) only displayed when H10 is set to 1. # H17, H18 are used when F2, F3 are set to 1 (S-curve)
30
nOn
dwell frequency is applied to the motor during H8- [Dwell time].
A310
O
When run frequency is issued, motor starts to accelerate after
Run frequency cannot be set within the range of H11 thru H16.
0.1~400
1
0
low limit 1]
high limit 1]
Adj.
during run
Clears the fault history saved in H 1-5.
0~10 [sec] Sets the time for dwell operation.
select]
Sets the code number to jump.
-
0.1~400
A307
[Dwell frequency]
[Hz]
H20
[Fault history 1]
[Fault history 2]
Factory
defaults
Description
0
O
Compact & Powerful Drive iG5A
Function group 2
LED
display
Address for
communication
Parameter
name
Min/Max
range
This parameter is active to prevent any possible fault when the
drive outputs its voltage to the running motor.
1. H20- 2. Restart
3. Operation 4. Normal
-
2
-
3
4
[Speed Search
1) A316
0 ~ 15
H22
Select]
H25
during Speed A318
[P gain during H26
H27
H30
H31
-
1. H20- [Power On start]
A31A
A31B
A31E
A31F
2. Restart
after instant power failure
-
-
after fault
6
-
-
80~200
search]
Speed search]
[I gain during speed search]
[Number of Auto
Restart try]
[Auto Restart
time]
[Motor type
select]
[Number of motor poles]
[%]
Bit 1
Bit 0
-
-
-
8
-
10
-
-
accel
-
-
-
-
-
-
-
-
-
This parameter limits the amount of current during speed search.
The set value is the percentage of the H33- [Motor rated current].
100
O
0~9999
It is the Proportional gain used for Speed Search PI controller.
100
O
0~9999
It is the Integral gain used for Speed search PI controller.
200
O
0
O
1.0
O
This parameter sets the number of restart tries after a fault
3. Operation 4. Normal
Bit 3
5
Bit 2
O
-
-
15
[Current level A317
A319
-
-
0
-
14
-
13
power failure
12
-
Adj.
during run
accel after fault
-
-
11
H24
-
9
On start]
after instant 7
[Power 0
1
H23
Factory
defaults
Description
0 ~10
0~60
[sec]
occurs. Auto Restart is deactivated if the fault outnumbers the
restart tries. This function is active when [drv] is set to 1 or 2
{Run/Stop via control terminal}. Deactivated during active
protection function (OHT, LVT, EXT, HWT etc.).
This parameter sets the time between restart tries.
0.2
0.2~ 22.0 ~
22.0
2 ~ 12
0.2kW
2)
~ 7.5
22.0kW
X
4
X
This setting is displayed via rPM in drive group.
1) Normal acceleration has first priority. Even though #4 is selected along with other bits, Drive performs Speed search #4.
2) H30 is preset based on drive rating.
Drive Starvert iG5A Series
31
iG5A
Function List
Function group 2
LED
display
Address for
communication
Parameter
name
Min/Max
range
H32
fs = fr -
A320
[Rated slip 0 ~ 10
frequency][Hz]
Factory
defaults
Adj.
during run
1)
2.33
X
Description
[
rpm X p
]
120
Where, fs = Rated slip frequency
fr = Rated frequency
rpm = Motor nameplate RPM
p = Number of Motor poles
H33
A321
H34
H36
[Motor rated
0.5~150
current]
[A]
[No Load Motor 0.1~ 50
A322
Current] [A]
50~100
A324
[Motor efficiency]
[%]
H37
A325
[Load inertia rate]
0~2
H39
H40
A327
[Carrier
1 ~ 15
frequency
[kHz]
select]
A328
[Control mode
select]
0~3
H41
H42
[Stator resistance 0 ~ 28
A32A
(Rs)] [Ω]
H44
H45 2)
H46
H47
A329
A32C
A32D
H49
[Leakage A32F
A330
A331
0~1
0~ 300.0
inductance (Lσ )][mH]
[Sensorless P gain]
[Sensorless
A32E
I gain]
H48
[Auto tuning]
[Sensorless torque limit]
PWM mode
select
PID select
0~ 32767
100~220
[%]
0~1
0~1
1) H32 ~ H36 factory default values are set based on OTIS-LG motor.
2) Set H40 to 3 (Sensorless vector control) to display this parameter.
32
Enter the current value detected when the motor is rotating in
rated rpm after the load connected to the motor shaft is removed.
Enter the 50% of the rated current value when it is difficult to
measure H34 - [No Load Motor Current].
Enter the motor efficiency (see motor nameplate).
Select one of the following according to motor inertia.
0
1
2
Enter motor rated current on the nameplate.
Less than 10 times
About 10 times
More than 10 times
This parameter affects the audible sound of the motor, noise
emission from the drive, drive temp, and leakage current. If the
set value is higher, the drive sound is quieter but the noise from
the drive and leakage current will become greater.
0
1
3
{Volts/frequency Control}
{Slip compensation control}
{Sensorless vector control}
If this parameter is set to 1, it automatically measures
26.3
X
11
X
87
X
0
X
3
O
0
X
0
X
This is the value of the motor stator resistance.
-
X
This is leakage inductance of the stator and rotor of the motor.
-
X
P gain for Sensorless control
1000
O
I gain for Sensorless control
100
O
180.0
X
0
X
0
X
parameters of the H42 and H44.
Limits output torque in sensorless mode.
If you want to limit a drive leakage current, select 2 phase PWM
mode.
It has more noise in comparison to Normal PWM mode.
0
1
Normal PWM mode
2 phase PWM mode
Selects whether using PID control or not
Compact & Powerful Drive iG5A
Function group 2
LED
display
H50 1) H51
H52
H53
H54
H55
H56
Address for
communication
Parameter
name
Min/Max
range
A332
[PID F/B select]
0~1
A333
[P gain for PID]
A334
A335
A336
A337
A338
H57
A339
[Differential time 0 ~ 30.0
for PID [sec]
for PID (D gain)]
[sec]
[PID control
0~1
mode select]
[PID output 0.1 ~ 400
[Hz]
limit]
[PID output frequency low 1
Terminal I input (0 ~ 20 mA)
Terminal V1 input (0 ~ 10 V)
0.1 ~ 400
[Hz]
limit]
0
X
300.0
O
1.0
O
0.0
O
This parameter sets the gains for the PID controller.
Selects PID control mode
1
0
0
Normal PID control
Process PID control
This parameter limits the amount of the output frequency through 60.00
X
O
the PID control.
and F23 - [Start frequency].
0.50
O
Loader digital setting 2
0
X
I terminal setting: 0~20mA
The value is settable within the range of F21 ? [Max frequency]
Selects PID standard value.
[PID standard
0~4
0
1
value select]
2
4
A33A
H60
0.1~32.0
frequency high 0
[%]
[Integral time Adj.
during run
Standard value is indicated in “rEF” of Drive group.
H58
0~ 999.9
Factory
defaults
Description
A33C
3
PID control
unit select
0~1
[Self-diagnostic 0~3
select] Loader digital setting 1
V1 terminal setting 2: 0~10V
Setting as a RS-485 communication
Selects a unit of the standard value or feedback amount.
0
Frequency[Hz]
0
Self-diagnostic disabled
1
1
2
3
0
X
Percentage[%]
IGBT fault/Ground fault
Output phase short & open/ Ground fault
0
X
Ground fault (This setting is unable when more than 11kW) H61 2) A33D
[Sleep delay time] 0~2000[s] Sets a sleep delay time in PID drive.
60.0
X
H62
A33E
[Sleep frequency] 0~400[Hz] control drive.
0.00
O
A33F
35.0
O
H63
H64
H65
H66
H67
H70
A340
A341
A342
A343
A346
Sets a sleep frequency when executing a sleep function in PID
[Wake up level]
[KEB drive select]
0~100[%] Sets a wake up level in PID control drive.
[KEB action start level]
[KEB action stop level]
[KEB action gain]
[Frequency Reference for Accel/Decel]
You canʼt set more than Max. frequency(F21)
0~1
110~140
[%]
110~145
[%]
1~20000
0~1
Sets KEB drive.
0
X
Sets KEB action start level according to level.
125.0
X
Sets KEB action stop level according to level.
130.0
X
1000
X
0
X
Sets KEB action gain.
0
Based on Max freq (F21)
1
Based on Delta freq.
1) Set H49 to 1 (PID control) to display this parameter.
2) Set H49 as a 1
3): it is indicated when setting H64(KEB drive select) as a 1 (KEB does not operate when cut power after loading ting input (about 10%).
Drive Starvert iG5A Series
33
iG5A
Function List
Function group 2
LED
display
H71
Address for
communication
Parameter
name
Min/Max
range
0
[Accel/Decel
1
A347
0~2
time scale]
2
Settable unit: 0.01 second.
Settable unit: 0.1 second.
Settable unit: 1 second.
This parameter selects the parameter to be displayed on the
keypad when the input power is first applied.
0
Frequency command
2
Decel time
1
H73
H75
H76
9
10
Motor rpm
Drive DC link voltage
User display select (H73)
13
15
17
select].
12
14
16
One of the following can be monitored via vOL - [User display
A349
[Monitoring
item select]
0~2
A34A
[Gain for Motor 1 ~ 1000
operating rate 0~1
[DB resistor 0 ~ 30
A34B
A34C
rpm display]
[DB resistor limit select]
operating rate]
A34D
H77 1)
[Cooling fan [Operating H79
Output current
11
H78
Multi-Step frequency 3
8
H74
display]
A34E
A34F
control]
method select when cooling fan
malfunctions]
[S/W version]
0
[%]
0~1
0~1
0 ~ 10.0
Fault display
Direction of motor rotation select
Output current 2
Motor rpm 2
Drive DC link voltage 2
User display select 2
Output voltage [V]
1
Output power [kW]
2
[%]
Torque [kgf, m]
This parameter is used to change the motor rotating speed (r/
min) to mechanical speed (m/mi) and display it.
0
0
1
Use DB resistor for the H76 set time.
during one sequence of operation.
0 Always ON
1
Keeps ON when its temp is higher than drive protection
limit temp. Activated only during operation when its temp
is below that of drive protection limit.
0
Continuous operation when cooling fan malfunctions.
1
Operation stopped when cooling fan malfunctions.
This parameter displays the drive software version.
O
Unlimited
Set the percent of DB resistor operating rate to be activated
O
0
1) Exception: Since SV004iG5A-2/SV004iG5A-4 is Natural convection type, this code is hidden.
34
Multi-Step frequency 2
7
Multi-Step frequency 1
6
0 ~ 15
O
Frequency mode
5
[Power on 1
Drive mode
4
A348
Adj.
during run
Accel time
3
H72
Factory
defaults
Description
100O
1
O
10O
0
O
0
O
1.0
X
Compact & Powerful Drive iG5A
Function group 2
LED
display
Parameter
Min/Max
name
range
[2nd motor A351
H81 1)
Accel time]
0 ~ 6000
[2nd motor [sec]
H82 A352
Decel time]
[2nd motor 30 ~ 400
H83 A353
base frequency]
[Hz]
[2nd motor 0~2
H84 A354
V/F pattern]
[2nd motor forward
H85 A355
torque boost]
0 ~ 15
[2nd motor reverse [%]
H86 A356
torque boost]
[2nd motor stall 30~150
H87 A347
prevention level]
[%]
[2nd motor 50~200
A358
Electronic thermal H88 [%]
level for 1 min]
[2nd motor H89
Address for
communication
A359
H90
Electronic thermal level for A35B
[Parameter read]
0~1
H92
A35C
[Parameter write]
0~1
H93
initialize]
0~5
H94
A35E
H95
A35F
[Password register]
[Parameter lock]
10.0
O
60.00
X
0
X
5
X
5
X
150
X
Copy the parameters from drive and save them into remote
loader.
drive.
0
-
2
Only Drive group is initialized.
4
Only Function group 2 is initialized.
O
100O
26.3
X
0
X
0
X
Copy the parameters from remote loader and save them into
All parameter groups are initialized to factory default
1
value.
0
3
5
0 ~ FFFF
O
factory default value.
[Parameter
5.0
150
This parameter is used to initialize parameters back to the
A35D
Adj.
during run
[%]
H91 2) This parameter actives when the selected terminal is ON after I17-I24 is set to 12 {2nd motor select}.
50~150
continuous]
[2nd motor 0.1~100
A35A
rated current]
[A]
Factory
defaults
Description
X
Only Function group 1 is initialized.
Only I/O group is initialized.
Password for H95-[Parameter lock].
Set as Hexa value.
0O
This parameter is able to lock or unlock parameters by typing
0 ~ FFFF
password registered in H94.
UL (Unlock)
L (Lock)
Parameter change enable
0
O
Parameter change disable
1) It is indicated when choosing I17~I24 as a 12 (2nd motor select).
2) H91,H92 parameters are displayed when Remote option is installed.
Drive Starvert iG5A Series
35
iG5A
Function List
Input/output group
LED
display
I0
I2
I3
I4
I5
I6
I7
I8
I9
I10
I11
I12
I13
I14
I15
I16
I17
I18
I19
I20
Address for
communication
Parameter
name
Min/Max
range
A400
[Jump code]
0 ~ 87
A402
[NV input Min voltage] 0 ~ -10
[V]
[Frequency 0 ~ 400
A403
corresponding to I 2] [Hz]
A404
[NV input Max voltage] 0 ~ -10
[V]
[Frequency 0 ~ 400
A405
corresponding to I 4][Hz]
A406
A407
Adj.
during run
1
O
0.00
O
0.00
O
10.0
O
60.00
O
10
O
0
O
0.00
O
10
O
60.00
O
10
O
4.00
O
0.00
O
20.00
O
60.00
O
activated below half of set value.
0
O
Forward run command
Sets the code number to jump.
Sets the minimum voltage of the NV (-10V~0V) input.
Sets the drive output minimum frequency at minimum voltage of
the NV input.
Sets the maximum voltage of the NV input.
Sets the drive output maximum frequency at maximum voltage of
the NV input.
[Filter time constant 0 ~ 9999 Adjusts the responsiveness of V1 input (0 ~ +10V).
for V1 input] [V1 input Min 0 ~ 10
voltage] [V]
[Frequency 0 ~ 400
A408
corresponding to I 7][Hz]
A409
Factory
defaults
Description
[V1 input Max 0 ~ 10
voltage] [V]
[Frequency 0 ~ 400
A40A
corresponding to I 9][Hz]
Sets the minimum voltage of the V1 input.
Sets the drive output minimum frequency at minimum voltage of
the V1 input.
Sets the maximum voltage of the V1 input.
Sets the drive output maximum frequency at maximum voltage of
the V1 input.
Sets the input sectionʼs internal filter constant for I input.
[Filter time
A40B
constant for I input] 0 ~ 9999
A40C
A40D
A40E
[I input Min 0 ~ 20
Sets the minimum current of I input.
[Frequency 0 ~ 400
Sets the drive output minimum frequency at minimum current of I
[I input Max 0 ~ 20
Sets the Maximum current of I input.
current] [mA]
corresponding to I 12][Hz]
current] [mA]
input.
[Frequency 0 ~ 400
A40F
corresponding to I 14][Hz]
Sets the drive output maximum frequency at maximum current of
1
A410
[Criteria for Analog Input Signal loss]
[Multi-function P1 define]
A411
A412
A413
A414
0~2
I input.
0
Disabled
2
activated below set value.
0
input terminal
Reverse run command
2
Emergency Stop Trip
3
Reset when a fault occurs {RST}
4
Jog operation command
5
Multi-Step freq - Low
[Multi-function
6
Multi-Step freq - Mid
P4 define]
7
Multi-Step freq - High
[Multi-function
input terminal
P2 define]
[Multi-function
input terminal
P3 define]
input terminal
0 ~ 27
* See °∞Chapter 14 Troubleshooting and maintenance°± for External trip A/B contact.
* Each multi-function input terminal must be set differently.
36
0
1
1
2
3
O
O
O
O
Compact & Powerful Drive iG5A
Input/output group
LED
display
I21
I22
I23
Address for
communication
Parameter
name
[Multi-function
8
Multi Accel/Decel - Low
P5 define]
9
Multi Accel/Decel - Mid
[Multi-function
10
Multi Accel/Decel - High
P6 define]
11
DC brake during stop
[Multi-function
12
2nd motor select
P7 define]
13
-Reserved-
A415
A416
A417
Min/Max
range
input terminal
input terminal
input terminal
14
15
0 ~ 27
-Reserved
Up-down
16
I24
I25
I26
A418
External trip: B Contact (EtB)
I31
I32
I33
I34
I35
I36
22
25
27
24
26
A419
A41A
A41B
I30
21
P8 define]
A41E
[Output terminal
constant for Multi-function
1 ~ 15
A423
Accel/Decel Disable
Up/Down Save Freq. Initialization
JOG-FX
JOG-RX
P7
P6
P5 P4
BIT2 BIT1 BIT0
P3
[Multi-Step [Hz]
[Multi-Accel time 1]
[Multi-Decel time 1]
[Multi-Accel
A424
time 2]
0~ 6000
[sec]
P2
BIT0
P1
MO
is getting slower.
It cannot be set greater than F21 - [Max frequency].
0
O
0
O
If the value is set higher, the responsiveness of the Input terminal
[Multi-Step frequency 6]
O
Analog Hold
frequency 4]
[Multi-Step
A421
frequency 7]
A422
2nd Source
Input terminal]
0 ~ 400
7
Change from PID operation to V/F operation
3AC
[Filtering time O
Self-diagnostic function
BIT1
status display]
[Multi-Step
A41F
frequency 5]
A420
P8
status display]
O
External trip: A Contact (EtA)
BIT7 BIT6 BIT5 BIT4 BIT3
[Input terminal
O
Frequency decrease command (DOWN)
19
20
input terminal 4
5
Frequency increase (UP) command
3-wire operation
23
I27
[Multi-function
Adj.
during run
6
17
18
Factory
defaults
Description
4
O
30.00
O
25.00
O
20.00
O
15.00
O
3.0
O
3.0
4.0
Drive Starvert iG5A Series
37
iG5A
Function List
Input/output group
LED
display
I37
I38
I39
I40
I41
I42
I43
I44
I45
I46
I47
Address for
communication
A425
Parameter
name
Min/Max
range
[Multi-Decel time 2]
[Multi-Accel
A426
time 3]
[Multi-Decel
A427
time 3]
A42A
[Multi-Accel time 5]
6.0
6.0
0~ 6000
[Multi-Decel
A42B
time 5]
7.0
8.0
8.0
[Multi-Accel
A42E
time 7]
9.0
[Multi-Decel
A42F
time 7]
A432
A433
I52
A434
I53
I54
A435
A436
I55
[Analog output
item select]
[Analog output
level adjustment]
[Frequency detection level]
[Frequency detection
9.0
A437
0~3
10~200
[%]
[Hz]
bandwidth]
output terminal
select]
[Multi-function
relay select]
Output item
Output to 10[V]
1
150 %
0
Output freq.
2
Output voltage
3
Output current
Drive DC link voltage
Based on 10V.
Cannot be set higher than F21.
Max frequency
AC 282V
DC 400V
400V
0
O
100
O
30.00
O
10.00
O
AC 564V
DC 800V
0
FDT-1
12
2
FDT-3
1
3
4
0 ~ 19
200V 0 ~ 400 Used when I54 or I55 is set to 0-4.
[Multi-function 38
[Multi-Decel
A42D
time 6]
I51
7.0
[sec]
[Multi-Accel
A42C
time 6]
4.0
5.0
[Multi-Accel
A428
time 4]
[Multi-Decel
A429
time 4]
Adj.
during run
5.0
I50
Factory
defaults
Description
5
6
7
8
9
FDT-2
FDT-4
FDT-5
Overload (OLt)
Drive Overload (IOLt)
Motor stall (STALL)
Over voltage trip (Ovt)
Low voltage trip (Lvt)
17
O
Compact & Powerful Drive iG5A
Input/output group
LED
display
Address for
communication
Parameter
name
Min/Max
range
I55
10
Drive Overheat (OHt)
12
During Run
11
A437
[Multi-function relay select]
13
0 ~ 19
14
15
16
17
18
19
A438
[Fault relay output]
0~7
I57
A439
I59
I60
I61
select when communication
0~3
error occurs] auto restart try] occurs
[Communication 0 ~1
A43C
[Drive number]
1 ~ 250
A43D
protocol select] [Baud rate]
0~4
I62
A43E
occurs
0
-
Bit 2
1
-
-
Bit 1
-
-
-
-
-
1
-
of frequency
command]
-
1
-
-
LS BUS
Set for RS485 communication
Select the Baud rate of the RS485.
1200 [bps]
2
4800 [bps]
1
2400 [bps]
2
0
O
0
X
1
O
3
O
19200 [bps]
Continuous operation at the frequency before its
0
command is lost.
1
9600 [bps]
RS485.
0~2
Multi-function output terminal
Modbus RTU
0
Bit 0
3
Set communication protocol.
0
-
It is used when freq command is given via V1 /I terminal or
[Drive mode select after loss Multi-function relay -
-
Bit 1
0
O
low voltage trip
Bit 0
-
4
voltage trip
3
H26 - [Number of other than low 2
A43B
Brake signal select
2
Warning for cooling fan trip
7
[Output terminal O
Multi-function relay select
When the
2
17
Wait time for run signal input
6
During speed searching
5
During constant run
4
During Stop
When setting the When the trip 3
Adj.
during run
Command loss
I56
Factory
defaults
Description
0
O
Free Run stop (Output cut-off)
Decel to stop
Drive Starvert iG5A Series
39
iG5A
Function List
Input/output group
LED
display
I63
I64
Address for
communication
[Wait time after
[Communication A440
I67
I68
I69
I70
I71
I72
I73
I74
I75
I76
I77
I78
I79
I80
I81
This is the time drive determines whether there is the input
A441
A442
time setting]
[Parity/stop bit
setting]
[Read address A443
[Read address
A445
A446
A447
A448
A449
A44A
A44B
A44C
A44D
A44E
A44F
A450
A451
182 1) A452
[ms]
0~3
A444
2 ~ 100
0
Parity: None, Stop Bit: 1
2
Parity: Even, Stop Bit: 1
1
Parity: None, Stop Bit: 2
Parity: Odd, Stop Bit: 1
5
O
O
O
7
register 3]
[Read address
0~42239
register 5]
The user can register up to 8 discontinuous addresses and read
them all with one Read command.
8
9
O
[Read address
10
register 6]
[Read address
11
register 7]
[Read address
12
register 8]
[Write address 5
register 1]
[Write address 6
register 2]
[Write address 7
register 3] [Write address
[Write address
O
6
[Read address
register 4]
1.0
5
register 2]
[Read address
Adj.
during run
When the protocol is set, the communication format can be set.
3
0~42239
register 5]
The user can register up to 8 discontinuous addresses and write
them all with one Write command
7
register 7]
[Write address
current]
5
O
[Write address
[Brake open 6
register 6]
register 8]
8
[Write address
1) It is indicated when choosing I54~I55 as a 19 (Brake signal).
40
Frame communication time
register 1] register 4]
Factory
defaults
Description
0.1 ~ 120 frequency command or not. If there is no frequency command
A43F
loss of frequency
[sec]
input during this time, drive starts operation via the mode
command]
selected at I62.
I66
Min/Max
range
I65
Parameter
name
8
0~180
[%]
Sets current level to open the brake.
It is set according to H33ʼs (motor rated current) size
50.0
O
Compact & Powerful Drive iG5A
Input/output group
LED
display
183
184
185
186
187
Address for
communication
A453
A454
A455
`
A456
A457
Parameter
name
Min/Max
range
[Brake open 0~10
[Brake open FX 0~400
[Brake open RX 0~400
[Brake close 0~19
[Brake close 0~400
delay time]
[s]
frequency][Hz]
frequency][Hz]
delay time]
[s]
frequency[Hz]
Factory
defaults
Adj.
during run
Sets Brake open dely time.
1.00
X
Sets FX frequency to open the brake
1.00
X
Sets RX frequency to open the brake
1.00
X
Sets delay time to close the brake
1.00
X
Sets frequency to close the brake
2.00
X
Description
Drive Starvert iG5A Series
41
iG5A
Protective Functions
Keypad display
Protective functions
Descriptions
The drive turns off its output when the output current of the drive flows more than 200% of the drive rated
current.
The drive turns off its output when a ground fault occurs and the ground fault current is more than the internal
setting value of the drive.
The drive turns off its output when the output current of the drive flows more than the rated level (150% for 1
minute).
The drive turns off its output if the output current of the drive flows at 150% of the drive rated current for more
than the current limit time (1min).
The drive turns off its output if the heat sink overheats due to a damaged cooling fan or an alien substance in
the cooling fan by detecting the temperature of the heat sink.
The drive turns off its output when the one or more of the output (U, V, W) phase is open. The drive detects
the output current to check the phase loss of the output.
The drive turns off its output if the DC voltage of the main circuit increases higher than 400V when the motor
decelerates. This fault can also occur due to a surge voltage generated at the power supply system.
The drive turns off its output if the DC voltage is below 180V because insufficient torque or overheating of the
motor can occur when the input voltage of the drive drops.
The internal electronic thermal of the drive determines the overheating of the motor. If the motor is overloaded, the drive turns off
the output. The drive cannot protect the motor when driving a motor having more than 4 poles or multi motors.
Drive output is blocked when one of R, S, T is open or the electrolytic capacitor needs to be replaced.
Displayed when IGBT damage, output phase short, output phase ground fault or output phase open occurs.
Displayed when user-setting parameters fails to be entered into memory.
Displayed when an error occurs in the control circuitry of the drive.
Displayed when the drive cannot communicate with the keypad.
Displayed when the drive and the remote keypad do not communicate with each other.
It does not stop drive operation.
Displayed after the drive resets the keypad when
a keypad error occurs and this ....
Displayed when a fault condition occurs in the drive cooling fan.
Used for the emergency stop of the drive. The drive instantly turns off the output when the EST terminal is turned on.
Caution: The drive starts to regular operation when turning off the EST terminal while FX or RX terminal is ON.
When multi-function input terminal (I20-I24) is set to 19
{External fault signal input A: (Normal Open Contact)}, the drive turns off the output.
When multi-function input terminal (I20-I24) is set to 19
{External fault signal input B: (Normal Close Contact)}, the drive turns off the output.
When drive operation is set via analog input (0-10V or 0-20mA input) or option (RS-485) and no signal is applied,
operation is done according to the method set in I62 (Operating method when the frequency reference is lost).
42
Compact & Powerful Drive iG5A
Fault Remedy
Keypad display
Cause
Remedy
Caution: W
hen an overcurrent fault occurs, operation must be started after the cause is removed
to avoid damage to IGBT inside the drive.
Accel/Decel time is too short compared to the GD2 of
the load.
Load is greater than the drive rating.
Drive output is issued when the motor is free running.
Output short circuit or ground fault has occurred.
Mechanical brake of the motor is operating too fast.
→ Increase the Accel/Decel time.
→ Replace the drive with appropriate capacity.
→ R
esume operation after stopping the motor or use
H22 (Speed search).
→ Check output wiring.
→ Check the mechanical brake.
Ground fault current
Ground fault has occurred at the output wiring of the drive.
The insulation of the motor is damaged due to heat.
→ Check the wiring of the output terminal.
→ Replace the motor.
Drive overload
Load is greater than the drive rating.
Overload trip
Torque boost scale is set too large.
→ U
pgrade the capacity of motor and drive or reduce
the load weight.
→ Reduce torque boost scale.
Heat sink overheat
Cooling system has faults.
An old cooling fan is not replaced with a new one.
Ambient temperature is too high.
→ Check for alien substances clogged in the heat sink.
→ R
eplace the old cooling fan with a new one.
→ Keep ambient temperature under 50°C.
Output Phase loss
Faulty contact of magnetic switch at output.
Faulty output wiring.
Cooling fan fault
An alien substance is clogged in a ventilating slot.
Drive has been in use without changing a cooling fan.
→ M
ake connection of magnetic switch
at output of the drive securely.
→ Check output wiring.
→ C
heck the ventilating slot and remove
the clogged substances.
→ Replace the cooling fan.
Decel time is too short compared to the GD2 of the load.
Regenerative load is at the drive output.
Line voltage is too high.
→ Increase the Decel time.
→ Use Dynamic Brake Unit.
→ Check whether line voltage exceeds its rating.
Line voltage is low.
Load larger than line capacity is connected to line
(ex: welding machine, motor with high starting current
connected to the commercial line).
Faulty magnetic switch at the input side of the drive.
→ Check whether line voltage is below its rating.
→ C
heck the incoming AC line.
Adjust the line capacity corresponding to the load.
Overcurrent
Over voltage
Low voltage
Electronic thermal
External fault A
contact input
Motor has overheated.
Load is greater than drive rating.
ETH level is set too low.
Drive capacity is incorrectly selected.
Drive has been operated at low speed for too long.
→
→
→
→
→
→
Change a magnetic switch.
Reduce load weight and operating duty.
Change drive with higher capacity.
Adjust ETH level to an appropriate level.
Select correct drive capacity.
Install a cooling fan with a separate power supply.
The terminal set to “18 (External fault- A)" or
“19 (External fault-B)” in I20-I24 in I/O group is ON.
→ E
liminate the cause of fault at circuit connected to
external fault terminal or cause of external fault input.
Operating method
when the frequency
command is lost
No frequency command is applied to V1 and I.
→ C
heck the wiring of V1 and I and frequency
reference level.
Remote keypad
communication error
Communication error between drive
keypad and remote keypad.
→ C
heck for connection of communication line and
connector.
- EEP: Parameter save error
- HWT: Hardware fault
- Err: Communication Error
- COM: Keypad error
→ Contact your LSIS sales distributor.
External fault B
contact input
Drive Starvert iG5A Series
43
•For your safety, please read user's manual thoroughly before operating.
•Contact the nearest authorized service facility for examination, repair, or adjustment.
Safety Instructions
•Please contact a qualified service technician when you need maintenance.
Do not disassemble or repair by yourself!
•Any maintenance and inspection shall be performed by the personnel having expertise concerned.
© 2005.5 LSIS Co.,Ltd. All rights reserved.
■HEAD OFFICE
LS Tower, 127, LS-ro, Dongan-gu, Anyang-si, Gyeonggi-do, Korea
■EMEA +82-2-2034-4901 / [email protected]
■Asia Pacific / Americas +82-2-2034-4620 / [email protected]
Overseas Branches
●
●
●
●
LSIS(Wuxi) Co., Ltd._Wuxi, China
No. 1, Lexing Road, Wuxi National High &New Tech Industrial Development Area, Wuxi214028, Jiangsu, P.T.China
Tel : 86-510-8534-6666-8005 / Fax : 86-510-8534-4078
●
●
●
LS Hukai Electric(Hubei) Co., Ltd._ Hubei, China
1st. Floor, Tupolevlaan 48, 1119NZ,Schiphol-Rijk, The Netherlands
Tel : 31-20-654-1420 / Fax : 31-20-654-1429
●
LSIS Japan Co., Ltd._Tokyo, Japan
Tokyo Club Building 13F, 2-6, Kasumigaseki 3-chome, Chiyoda-ku, Tokyo, 100-0013
Tel : 81-3-6268-8241 / Fax : 81-3-6268-8240
●
●
LSIS USA Inc._ Chicago, U.S.A.
2000 Millbrook Drive, Lincolnshire, Chicago, IL 60069, United States
Tel : 847-941-8240 / Fax : 847-941-8259
Specifications in this catalog are subject to change without notice due to
continuous product development and improvement.
2015. 01
LSIS Chengdu Office, China
Room1710, 17/F Huamin Empire Plaza, NO.1 Fuxin Road, Chengdu, P.R. China
Tel : 86-28-8670-3200 / Fax : 86-28-8670-3203
●
LSIS ShenYang Office, China
Room 803, Hongyuan Building, 52 South Nanjing Road, Heping District, Shenyang, P.R. China
Tel : 86-24-2321-9050 / Fax : 86-24-8386-7210
●
LSIS Europe B.V._Netherlands
LSIS Qingdao Office, China
Room 2001, Galaxy Building, 29 ShanDong Road, ShiNan District, QingDao, ShanDong, P.R. China
Tel : 86-532-8501-6058 / Fax : 86-532-8501-6057
Nguyen Khe, Dong Anh, Hanoi, Vietnam
Tel : 84-4-6275-8055 / Fax : 84-4-3882-0220
LOB 19-205, JAFZA View Tower, Jebel Ali Free Zone, Dubai, United Arab Emirates
Tel : 971-4-886-5360 / Fax : 971-4-886-5361
●
●
●
LSIS(ME) FZE_Dubai, U.A.E.
LSIS Guangzhou Office, China
Room 1818-1820, Xinyuan Building,NO.898 Tianhe North Road, Tianhe District, Guangzhou, P.R China
Tel : 86-20-8326-6784 / Fax : 86-20-8326-6287
No. 100, Tanjiahe Road, Dianjun District, Yichang City, Hubei Province, 443004, China
Tel : 86-717-667-7339 / Fax : 86-717-667-7559
LS-VINA Industrial Systems Co., Ltd._Hanoi, Vietnam
LSIS Beijing Office, China
Room 2306, Building B Landgent Center, No.24 Middle Road, East 3rd Ring Road, Chaoyang District, Beijing, P.R. China
Tel : 86-10-5761-3127 / Fax : 86-10-5761-3128
LSIS(Dalian) Co., Ltd._Dalian, China
No. 15, Liaohexi 3-Road, Economic and Technical Development Zone, Dalian 116600, China
Tel : 86-411-8730-7510 / Fax : 86-411-8730-7560
LSIS Shanghai Office, China
32nd Floor, International Corporate City, No.3000 NorthZhongshan Road, Putuo District, Shanghai, China, 200063
Tel : 86-21-5237-9977 / Fax : 86-21-5237-7189
●
Overseas Subsidiaries
www.lsis.com
LSIS Jinan Office, China
Room 317, Chuangzhan Center, No. 201, Shanda Road, Lixia District, Jinan, Shandong, P. R. China
Tel : 86-531-8699-7826 / Fax : 86-531-8697-7628
LSIS Co., Ltd. Tokyo Office, Japan
Tokyo Club Building 13F, 2-6, Kasumigaseki 3-chome, Chiyoda-ku, Tokyo, 100-0013
Tel : 81-3-6268-8241 / Fax : 81-3-6268-8240
●
LSIS Co., Ltd. Rep. Office, Vietnam
Gema Dept Tower 18F, 6 Le Thanh Ton, District 1, HCM, Vietnam
Tel : 84-8-3823-7890
●
LSIS Detroit Office, U.S.A.
5700 Crooks Rd, Suite 211, Troy, MI 48098, USA
Tel : 1-248-792-2637~8 / Fax : 1-248-792-2642
●
LSIS Co., Ltd. India Office, India
109 First Floor, Park Central, Sector-30, Gurgaon- 122 002, Haryana, India
Tel : 91-1244-930-077 / Fax : 91-1244-930-066
●
LSIS Moscow Office, Russia
123610, Krasnopresnenskaya, nab., 12, building 1, office №1005, Moscow, Russia
Tel : 7-495-258-1466/1467 / Fax : 7-495-258-1466/1467
●
LSIS U.K. Office, United Kingdom
G17 Bedford I-Lab, Stannard Way, Priory Business Park, Bedford, MK44 3RZ, U.K.
Tel : 44-012-3483-4774 / Fax : 44-012-3483-4775
STARVERT iG5A (E) 2005. 05/(22) 2014. 06 Printed in Korea Pacomkorea