Download User`s Manual

ELE
C T
RI
C
G3INV-20DHT-R
AP
PL
IA
N
CE
S
User’sGLASSManual
PANEL HEATER
ELE
C T
RI
C
AP
PL
IA
N
CE
S
ENGLISH
Thank you for choosing INVENTOR
electrical appliances. For correct use
of this unit, please read this manual
carefully and and keep it for future
reference.
Air Outlet
Control Unit
Switch
Castor Wheel Stand
Model Number
G3INV-20DHT-R
Rated Power
Rated Voltage
2000W/1000W
Dimensions ( mm )
220V-240V~50Hz
820*100*450
Heating element
Temperature sensor
Switch
Tip over switch
KSD thermostat
KSD thermostat
13
12
11
7
15
14
IO N
10
1
TEM P
T IM ER
HIGH
ION
LOW
9
4
5
S et
6
8
2
3
4
5
6
7
Temperature( ) Indicator
Timer Indicator
Ionizer Indicator
Setting Button
Up Button
Down Button
Power button
High Heating Indicator
Low Heating Indicator
Heating Element Working Indicator
Children Safety Lock Indicator
LED Number Display
13 Temperature Unit Indicator
14 Low/ high Heating Selection
15 Generator(ION) Button
2.Operation Guide
Plug in the unit, the power indicator lights up after a short buzz . Press “ 7 ” to turn on the unit,
room temperature is displayed while the whole screen will be light up and the
default-factory set temperature is 25℃.
Press“ 4 ” to set the temperature, “ 12 ” and“ 1 ” will flash , then press“ 5 ” or“ 6 ” arrow buttons
to add 1℃ or reduce 1℃. The maximum setting temperature is 36℃, while the minimum
one is 5℃. Keeping pressing“ 5 ”or“ 6 ”to add or reduce 1℃ in 0.5 S. Thelast setting
temperature is the valid one. If no operation within 3S, the system will return the running
state, “ 1 ”indicator will not flesh while room temperature is displayed.
Press“ 4 ” once again to set timer, setting time is displayed while timer indicator flesh (the
timer unite is hour). Pressing“ 5 ”or“ 6 ”to add or reduce 1 hour, the timer range is 0-24 hour.
Keeping pressing“ 5 ”or“ 6 ”to add or reduce 1 hour in 0.5 second. The factory-set timer is 0
hour. With indicator lighting, the system starts to time according to last setting time if there is
no operation for 5 seconds. Each time“ 5 ”or“ 6 ”is pressed to set timer, system restarts to
time by new time, or it does by original one till timing is over, then turns off and stops working.
The unit is turned off without buzz hint when timing is over.
Keeping pressing“ 7 ”in any status to turn off the unit and power indicator keep light.
Under the working mode, press both“ 5 ” or “ 6 ”at the same time for 3 seconds to lock the
system. Then a square“ 11 ”is displayed.
Methods to unlock: 1) Shut off the electric machine.
2) Press both“ 5 ” or “ 6 ”for 3 seconds.
When did not enter any models, pressing“ 5 ”to select the output power, the heater will work
the full rated output while “ 8 ”is displayed . Pressing “ 6 ”to switch to “ 9 ”heating mode . Or
through high /low on the remote control switch button“ 8 ”to choose the output power.
8
(Optional Function)
ION indicator keep light, pressing the generator(ION)button“ 15 ”, the ionizer function will
be on or off.
9
Press any button there have buzzer ringing sound.
3
5
7
8
9
REPLACEMENT OF SUPPLY CORD
The supply cord damaged must be replaced by a service agent or
equivalent qualified person in order to prevent a hazard.
If you do not plan to use the heater for extended periods of time, it is
recommended that the heater is cleaned and then stored (preferably
in its original packaging) in a cool dry place.
Mo u n tin g G u id e
Specification
H
H1
L1
L
MODEL
G3INV-20DHT-R 2000/1000
820
450
522
344
Pull up the heater 5mm,
then move to left 10mm
to take down the heater.
Wall mounted mode
Take down the heater from wall
Caster Installation&removal
if the installation is complete,
it’s will hear a sound click.
press the button up,
take down the caster
Lock function for castor
Press down the lock button,
then the castor be locked