Download OWNER`S MANUAL - Bowtech Archery

O W N E R ’S M A N U A L
90554 Highway 99 North
Eugene, OR 97402
www.DiamondArchery.com
1
2
THANK YOU
Congratulations on your recent purchase! We at Diamond know that you have a choice when it
comes to your archery equipment, and we want to thank you for choosing us as your hunting
partner. Your feedback is important to us, as it is our desire to provide you with the absolute
finest products and customer service in the industry. Please take the time to go online and
register your new Fear No Evil Bow. It is equally important to read through this owner’s manual
as there are valuable tips to help keep your Fear No Evil bow trouble free for many seasons.
We encourage you to contact and utilize your local Dick’s Sporting Goods store as they can
assist you with purchases, services and accessories. To locate the Dick’s Sporting Goods store
nearest you, visit www.DicksSportingGoods.com/storeLocator. Frequently asked questions and
additional contact information can also be found at DicksSportingGoods.com.
BEFORE USING YOUR NEW FEAR NO EVIL BOW, READ AND UNDERSTAND THE FOLLOWING
MATERIAL OUTLINED IN THIS MANUAL. FAILURE TO FOLLOW ANY OF THESE WARNINGS
AND INSTRUCTIONS CAN DAMAGE THE BOW AND MAY CAUSE SERIOUS INJURY TO
YOURSELF AND/OR OTHERS.
DISCLAIMER OF LIABILITY: By accepting a Diamond product, the buyer agrees to hold
harmless Diamond and all associated parties from liability for any damage to persons or
property, which may result, for any reason, from the use of this product.
QUALITY
Every Fear No Evil bow has undergone a comprehensive quality control process and is built
from the highest quality components available. Most have been individually shot, tested and
measured to ensure compliance with our strict performance standards.
Lifetime Warranty
The Fear No Evil bow comes with a nontransferable lifetime warranty to the
registered original owner. This warranty
protects against any failures of the product
due to defects in material or workmanship
and does not include any damage due to
abuse, misuse or modification to the bow’s
design. The following exclusions apply.
Exclusions
Strings and cables, bearings, paint and/or
hydrographic film transferred finishes,
accessories to include: sights, arrow rests,
string silencers, quivers, or any other
components included as part of an accessory
package.
Damage caused by abuse, mishandling, dryfiring, alteration or modification to original
product. Other excluded damages are those
resulting from either loose module screws
or shooting arrows less than five grains per
pound of draw weight.
For the warranty to be enforceable the
original purchaser must complete and submit
the online registration form within 30 days of
purchase.
Dick’s Sporting Goods Stores
The Diamond Warranty covers product
purchased from Dick’s Sporting Goods
Stores. Fear No Evil bows purchased through
the Internet will not be warranted if not
purchased through a Dick’s Sporting Goods
store. Contact Dick’s Sporting Goods to
confirm that your purchase is through a Dick’s
Sporting Goods store.
4
Lifetime Warranty
cont.
Warranty Service
Our goal with all warranty returns is to have
the bow shipped out the door and on its
way back to your Dick’s Sporting Goods
store within 3 business days of receiving it
at our facilities in Eugene, Oregon. You are
our greatest asset, and we will give you the
highest quality and most efficient service
possible.
All products requiring warranty service must
be returned to a Dick’s Sporting Goods store
for inspection and diagnosis of any problem.
Your Dick’s Sporting Goods store can
determine whether factory service is required,
or if the service needed can be performed
at the store’s facility. In the event that a
bow must be returned for factory service, a
Return Authorization (RA) number must first
be obtained by your store. Bows returned to
the factory without an RA number will not be
accepted.
The bow owner is responsible for the
return prepaid freight to Diamond. No COD
shipments will be accepted. Diamond will
perform the warranty service required and
return the product to the store prepaid.
u All methods of shipping by UPS or FED-EX
only. Sender should insure all shipments.
u If your bow cannot be repaired, we reserve
the right to replace your bow with a newer
model of equal or greater value.
u Diamond reserves the right to substitute
any parts required for warranty coverage at
its sole discretion and for any reason.
Adjusting draw length
It is very important that your Fear No Evil bow is adjusted to fit you properly. Assistance in
achieving a proper fit should be provided by your Dick’s Sporting Goods store.
The Fear No Evil bow is preset to factory specifications with 29 inches draw length. You may need
to adjust your bow to match your draw length. Any other alterations to the factory setup will
likely inhibit performance.
The draw length of the Fear No Evil bow can be adjusted without draw length specific modules.
The Rotating Mod System makes this feature possible. By simply rotating the module clockwise
or counterclockwise, your draw length can be adjusted, typically in 1/2 inch increments. Refer to
Figure 1 and Chart 1
Module Screws
Cam
Indexing
Mark
Module
Indexing
Mark
Figure 1: Throttle Cam Tech Draw Length Adjustment
5
Adjusting draw length
1. Diamond recommends that you take your
bow to your Dick’s Sporting Goods store for
adjustment of your bow’s draw length.
cont.
bow was shipped with the indexing mark in
the #2 position at 29 inches of draw length,
you would place it in the #3 position for a 28
inch draw length.
2. Use a 3/32 inch hex wrench to remove the
module screws that attach the modules to
the cams.
6. Replace both module screws on each cam
and retighten. We recommend applying blue
Loctite 242 to the threads before replacing
them at your desired setting. This will prevent
the screws from loosening during normal use
of the bow.
3. Notice the numbered indexing mark on
the module and the indexing mark on the
cam. All bows are factory preset to a 29 inch
draw length, with the indexing marks aligned
for the this draw length setting. The lowest
numbered mark corresponds to the longest
draw length setting.
7. After repositioning the module, you will
need to reposition the draw stop posts. To do
this, use a 3/32 inch hex wrench to remove the
post from its current position.
4. To lengthen the draw length, rotate the
module so that the indexing mark on the cam
is aligned with a lower numbered indexing
mark on the module. For example, if your bow
was shipped with the indexing mark in the
#2 position at 29 inches of draw length, you
would place it in the #1 position for a 30 inch
draw length.
8. Replace the post in the position that
matches the position that you placed the
module in. For example, if the module was
placed in the #3 position, the draw stop post
should also be placed in the #3 position.
9. Please note that no bow press is typically
required to change the draw length of your
Fear No Evil bow. However, placing the
module in the #5 position may require the
use of a bow press.
5. To shorten the draw length, rotate the
module so that the indexing mark on the cam
is aligned with a higher numbered indexing
mark on the module. For example, if your
Chart 1: Throttle Cam Tech
Module & Post Settings
Fear No Evil bow
Module
Position
Draw Length
Module/Post
Setting
1
30
1
1.5
29.5
1.5
2
29
2
2.5
28.5
2.5
3
28
3
3.5
27.5
3.5
4
27
4
4.5
26.5
4.5
5
26
5
6
Cam timing
CENTER SHOT
Cable Centered
Between Marks
CAM TIMING
There are small indentations or “timing
marks” on the module-side of the cam
near its perimeter. When viewing the bow
directly from the module side of the cam,
the cable should be approximately centered
in between the timing marks as shown in
Figure 2. Adjusting the timing requires that
the bow be put in a press, and as such, your
Dick’s Sporting Goods store should perform
all timing adjustments.
SETTING THE DRAW
WEIGHT
Draw weights are adjustable 10 pounds
downward. For example, a 60 pound Fear
No Evil bow can be adjusted down to 50
pounds draw weight. Consult your local
Dick’s Sporting Goods store for information
regarding weight adjustment for your bow
model. All bows perform best at peak weight.
Draw weight can be adjusted by using a hex
wrench to either tighten or loosen the limb
bolt. The specific method for adjusting draw
length is described below.
WARNING: DO NOT TURN THE LIMB BOLTS
OUT MORE THAN THE RECOMMENDED
AMOUNT. Doing so could cause the limbs
to break out of their pockets and result in
bodily injury.
Limb Bolt
Pocket
Locking
Screw
Slot
Pocket
Pivot
Screw
Pocket
Locking
Screw
Figure 3: Draw Weight Adjustment (Dead Eye)
7
Center shot can be set by measuring from the
back of the riser to the arrow and then from
the front of the riser to the arrow. Once this is
equal, you are at the approximate center shot
of your bow (see Figure 5). This is a good
starting point when tuning your Fear No Evil
bow. Keep in mind, not all bows tune at exact
center shot due to the variances in arrow
spine, hand position, and your specific bow
poundage. Adjust your arrow rest until the
two measurements are equal.
Measure
Here
Measure
Here
Figure 5: Determining Center Shot
Figure 2: Throttle Cam Tech Timing
Bow Maintenance
Draw weight on the Fear No Evil bow can be
adjusted 10 pounds down from the bow’s
peak draw weight. For example, if the bow
is shipped as a 60 pound model, the draw
weight can be adjusted down to 50 pounds.
The procedure is as follows (See Figure 3):
1. Using a 5/32” hex wrench, loosen the
four pocket locking screws. The screws do
not need to be completely removed, only
loosened.
2. Using a 1/4” hex wrench, tighten or loosen
the limb bolts to increase or decrease draw
weight. One full turn equals approximately
2 pounds of draw weight. DO NOT back out
the limb bolt any more than 6 turns. When
the bow is backed out six turns, the pocket
locking screws will be near the end of their
slot. The top and bottom limb bolts should be
tightened and loosened equally.
3. Once the bow has been set as desired and
the limb bolts are adjusted equally, retighten
the pocket locking screws.
4. It is possible that adjusting the limb bolts
may have caused the pocket pivot screw to
loosen. For this reason, use a 5/32 inch hex
wrench to ensure that the pocket pivot screw
is tight.
Your Fear No Evil bow was made with the highest quality components to last for a lifetime of
use in the field with proper maintenance. It is important that you NEVER draw and release a
bow without an arrow on the string. This could not only hurt you, but can damage your bow. If
the bow is dry fired at any time, take it to your local Dick’s Sporting Goods store for a complete
inspection. Never leave your Fear No Evil bow in an area of extreme temperatures. This will cause
your string and cables to stretch which effects timing.
Before shooting your bow, always inspect the string and cables and check the limbs for any
visible damage. If damage is found, take the bow to your local Dick’s Sporting Goods store for
inspection or repair.
Your Fear No Evil bow comes equipped with sealed bearings for both the cam and idler. There is
no need to lubricate the bearings.
String & Cables
Your Diamond custom bowstring is manufactured to provide long string life and absolute
consistency, shot after shot. This results in greater accuracy and less time spent re-tuning your
equipment.
It is recommended that you cycle the bow 10-20 times to settle the string as a result of relaxation
during packaging and shipping.
Wax the string often. We recommend BCYML 6 synthetic string wax or an equivalent product.
To wax the string, apply wax liberally to entire length of string. Rub briskly with fingers until the
string appears slick. Remove all excess wax with a clean cloth. We recommend that you wax every
other time you shoot your bow to lengthen the life of your string and cable sets.
If you need assistance with setting up, tuning or solving an arrow flight problem, contact your
Dick’s Sporting Goods store.
8
SAFETY AND GENERAL INFORMATION
Your new Fear No Evil bow is a highly tuned,
precise shooting machine. It requires special
care and handling to achieve and maintain
peak performance. The string, cables and
limbs are under extreme tension, which
creates an incredible source of energy that
must not be taken for granted. Please respect
this power and use it properly.
The Fear No Evil bow has been standardized
to fit most manufacturers’ accessories and will
perform best when shot with a release.
ADULT SUPERVISION OF ALL CHILDREN
UNDER THE AGE OF 18 IS REQUIRED
Diamond has designed your bow to be a
safe and fun product. However, as with any
shooting style product, safety rules must be
observed. It is HIGHLY recommended that
these rules be read before using any bow.
Bows and arrows are NOT toys. For maximum
safety and enjoyment, always exercise caution
and common sense when shooting any bow.
WARNING: NEVER DRY FIRE THE BOW
NEVER draw a bow without an arrow nocked.
Doing so could cause personal injury and/or
damage the bow. When drawing a bow for
inspection or demonstration, never release
the string at full draw to let down. Hold onto
the string and do not let it slip out of your
hands. Without the resistance of a properly
weighted arrow to absorb the energy, you
may damage the bow and cause personal
injury to yourself and/or others.
ALWAYS wear safety glasses when operating
or adjusting your bow.
ALWAYS use an appropriate backstop for
maximum safety. An appropriate backstop
must be constructed of a durable material
and must extend beyond the perimeter of the
target. The recommended backstop size is
determined by the accuracy and ability of the
9
Owner’s Record
shooter. With a low level of shooter accuracy,
the backstop perimeter requirement must be
increased appropriately.
Date of Purchase:
NEVER aim or draw any bow in the direction of
a person. Aim and draw ONLY in the direction
of an appropriate target. ALWAYS have a full
view of the path to and beyond the target
when shooting.
Serial Number: Brace Height:
Draw Length: Draw Weight:
ALWAYS check all arrow components prior
to shooting, including nock, insert and tip.
Loose components can cause unbalanced
arrow flight and partial dry firing of the bow.
If an arrow has been damaged, or if you
believe it has been damaged, do not shoot it
again, as it could break on release, and sharp
arrow pieces could strike and injure you or
someone nearby.
NEVER retrieve arrows or allow anyone else to
do so until all arrows have been shot.
NEVER draw the bow without properly
adjusted limb bolts (see “Adjusting Draw
Weight” section for more information).
Make sure the string and cables are properly
attached to the correct post and in the correct
tracks in order to avoid possible injury.
Purchase Price:
Bow Model & Year:
IBO Speed Rating:
String Length:
Cable Length:
Store Purchased From:
Store’s Address:
City:
State:
Zip:
Phone No:
Email Address:
We encourage you to contact and utilize your local Dick’s Sporting Goods store as
they can assist you with purchases, services and accessories. To locate the dealer
nearest you, visit DicksSportingGoods.com/storeLocator. Frequently asked questions
and additional contact information can also be found at DicksSportingGoods.com.
SIGN UP FOR THE LIFETIME WARRANTY at
Registeryourbow.com
DO NOT attach anything to the cables or
string that could create excessive wear or slice
the string material. This will void the warranty.
DO NOT cross cables in any configuration
other than the configuration set by the
factory. This will have an adverse effect on the
performance and shootability of your bow.
Further, it may cause extreme wear to the
string, cable, and cable-slide/roller guard.
Any alteration from the factory specifications
or the adjustments outlined herein will void
the factory warranty. ALL maintenance must
be performed at a Dick’s Sporting Goods
store.
Every effort has been made to ensure the accuracy of information and typographical content within our owner’s
manual. Diamond reserves the right to modify and/or discontinue products without notice and at its discretion.
© 2013 Diamond Archery by BowTech. All rights reserved.
10